TLE214x, TLE214xA, TLE214xY EXCALIBUR LOW-NOISE HIGH-SPEED PRECISION OPERATIONAL AMPLIFIERS

Transcription

1 Low Noise 10 Hz n/ Hz 1 khz n/ Hz pF Load Capability 20-mA Min Short-Circuit Output Current 27-/µs Min Slew Rate High Gain-Bandwidth Product MHz Low IO µ Max at 25 C description TLE214x, TLE214xA, TLE214xY Single or Split Supply...4 to 44 Fast Settling Time 340 ns to 0.1% 400 ns to 0.01% Saturation Recovery ns Large Output Swing CC +0.1 to CC+ 1 The TLE214x and TLE214xA devices are high-performance, internally compensated operational amplifiers built using Texas Instruments complementary bipolar Excalibur process. The TLE214xA is a tighter offset voltage grade of the TLE214x. Both are pin-compatible upgrades to standard industry products. The design incorporates an input stage that simultaneously achieves low audio-band noise of 10.5 n/ Hz with a 10-Hz 1/f corner and symmetrical 40-/µs slew rate typically with loads up to 800 pf. The resulting low distortion and high power bandwidth are important in high-fidelity audio applications. A fast settling time of 340 ns to 0.1% of a 10- step with a 2-kΩ/100-pF load is useful in fast actuator/positioning drivers. Under similar test conditions, settling time to 0.01% is 400 ns. The devices are stable with capacitive loads up to 10 nf, although the 6-MHz bandwidth decreases to 1.8 MHz at this high loading level. As such, the TLE214x and TLE214xA are useful for low-droop sample-and-holds and direct buffering of long cables, including 4-mA to 20-mA current loops. The special design also exhibits an improved insensitivity to inherent integrated circuit component mismatches as is evidenced by a 500-µ maximum offset voltage and 1.7-µ/ C typical drift. Minimum common-mode rejection ratio and supply-voltage rejection ratio are 85 db and 90 db, respectively. Device performance is relatively independent of supply voltage over the ± 2- to ± 22- range. Inputs can operate between CC 0.3 to CC+ 1.8 without inducing phase reversal, although excessive input current may flow out of each input exceeding the lower common-mode input range. The all-npn output stage provides a nearly rail-to-rail output swing of CC 0.1 to CC+ 1 under light current-loading conditions. The device can sustain shorts to either supply since output current is internally limited, but care must be taken to ensure that maximum package power dissipation is not exceeded. Both versions can also be used as comparators. Differential inputs of CC± can be maintained without damage to the device. Open-loop propagation delay with TTL supply levels is typically 200 ns. This gives a good indication as to output stage saturation recovery when the device is driven beyond the limits of recommended output swing. Both the TLE214x and TLE214xA are available in a wide variety of packages, including both the industry-standard 8-pin small-outline version and chip form for high-density system applications. The C-suffix devices are characterized for operation from 0 C to 70 C, I-suffix devices from 40 C to 105 C, and M-suffix devices over the full military temperature range of 55 C to 125 C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright 1998, Texas Instruments Incorporated POST OFFICE BOX DALLAS, TEXAS

2 TA 0 C to 70 C 40 C to 105 C IOmax AT 25 C 500 µ 900 µ 500 µ 900 µ SMALL OUT- LINE (D) TLE2141ACD TLE2141CD TLE2141AID TLE2141ID TLE2141 AAILABLE OPTIONS PACKAGED DEICES CHIP CARRIER (FK) CERAMIC DIP (JG) 500 µ TLE2141AMD TLE2141AMFK TLE2141AMJG 55 C to 125 C 900 µ TLE2141MD TLE2141MFK TLE2141MJG The D packages are available taped and reeled. Add R suffix to device type (e.g., TLE2141ACDR). Chip forms are tested at TA = 25 C only. PLASTIC DIP (P) TLE2141ACP TLE2141CP TLE2141AIP TLE2141IP TLE2141AMP TLE2141MP CHIP FORM (Y) TLE2141Y TA 0 C to70 C 40 C to105 C IOmax AT 25 C SMALL OUTLINE (D) TLE2142 AAILABLE OPTIONS PACKAGED DEICES CHIP CARRIER (FK) CERAMIC DIP (JG) PLASTIC DIP (P) TSSOP (PW) 750 µ TLE2142ACD TLE2142ACP 1200 µ TLE2142CD TLE2142CP TLE2142CPWLE 750 µ TLE2142AID TLC2142AIP 1200 µ TLE2142ID TLC2142IP 750 µ TLE2142AMD TLE2142AMFK TLE2142AMJG TLC2142AMP 55 C to125 C 1200 µ TLE2142MD TLE2142MFK TLE2142MJG TLC2142MP The D packages are available taped and reeled. Add R suffix to device type (e.g., TLC2142ACDR). The PW packages are available left-ended taped and reeled. Add LE the suffix to device type (e.g., TLC2142CPWLE). Chip forms are tested at TA = 25 C only. CHIP FORM (Y) TLE2142Y TA 0 C to 70 C 40 C to 105 C IOmax AT 25 C 1.5 m 2.4 m 1.5 m 2.4 m SMALL OUTLINE (DW) TLE2144CDW TLE2144IDW TLE2144MDW TLE2144 AAILABLE OPTIONS PACKAGED DEICES CHIP CARRIER (FK) TLE2144AMFK TLE2144MFK CERAMIC DIP (J) TLE2144AMJ TLE2144MJ PLASTIC DIP (N) TLE2144ACN TLE2144CN TLE2144AIN TLE2144IN TLE2144AMN TLE2144MN 1.5 m 55 C to 125 C 2.5 m The DW packages are available taped and reeled. Add R suffix to device type (e.g., TLE2144CDWR). Chip forms are tested at TA = 25 C only. CHIP FORM (Y) TLE2144Y 2 POST OFFICE BOX DALLAS, TEXAS 75265

3 TLE2141 D, JG, OR P PACKAGE (TOP IEW) TLE2142 PW PACKAGE (TOP IEW) TLE2142 D, JG, OR P PACKAGE (TOP IEW) OFFSET N1 IN IN+ CC TLE2141 FK PACKAGE (TOP IEW) CC + OUT OFFSET N2 1OUT 1OUT 1IN 1IN+ CC CC CC+ CC+ 2OUT 2IN 2IN+ 2IN+ 1OUT 1IN 1IN+ CC TLE2142 FK PACKAGE (TOP IEW) CC + 2OUT 2IN 2IN+ IN IN+ OFFSET N CC OFFSET N2 CC + OUT 1IN 1IN + 1OUT CC IN + CC 2OUT 2IN TLE2144 DW PACKAGE (TOP IEW) TLE2144 J OR N PACKAGE (TOP IEW) TLE2144 FK PACKAGE (TOP IEW) 1OUT 1IN 1IN+ CC + 2IN+ 2IN 2OUT No internal connection 4OUT 4IN 4IN+ CC 3IN+ 3IN 3OUT 1OUT 1IN 1IN+ CC + 2IN+ 2IN 2OUT OUT 4IN 4IN+ CC 3IN+ 3IN 3OUT 1IN+ CC + 2IN+ 1IN 1OUT 3OUT 4OUT 3IN 4IN IN 2OUT 4IN+ CC 3IN+ POST OFFICE BOX DALLAS, TEXAS

4 symbol OFFSET N1 (see Note A) IN + IN + OUT OFFSET N2 (see Note A) NOTES: A. OFFSET N1 AND OFFSET N2 are only availiable on the TLE2241x devices. TLE2141Y chip information This chip, when properly assembled, displays characteristics similar to the TLE2141. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive epoxy or a gold-silicon preform. BONDING PAD ASSIGNMENTS (7) (6) (5) OFFSET N1 IN + IN OFFSET N2 (1) (3) (2) (5) CC+ (7) + (4) CC (6) OUT 64 (1) CHIP THICKNESS: 15 TYPICAL BONDING PADS: 4 4 MINIMUM (2) (3) (4) TJmax = 150 C TOLERAES ARE ±10%. ALL DIMENSIONS ARE IN MILS POST OFFICE BOX DALLAS, TEXAS 75265

5 TLE2142Y chip information This chip, when properly assembled, displays characteristics similar to the TLE2142. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive epoxy or a gold-silicon preform. BONDING PAD ASSIGNMENTS (2) (1) (8) (7) 1IN+ 1IN 2OUT (3) (2) (7) + CC+ (8) + (1) (5) (6) 1OUT 2IN+ 2IN (4) CC 90 (3) (6) CHIP THICKNESS: 15 TYPICAL BONDING PADS: 4 4 MINIMUM TJmax = 150 C TOLERAES ARE ±10%. (4) (5) 80 ALL DIMENSIONS ARE IN MILS. PIN 4 IS INTERNALLY CONNECTED TO BACKSIDE OF CHIP. POST OFFICE BOX DALLAS, TEXAS

6 TLE2144Y chip information This chip, when properly assembled, displays characteristics similar to the TLE2144. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive epoxy or a gold-silicon preform. (12) (13) BONDING PAD ASSIGNMENTS (11) (10) (9) 1IN+ 1IN (3) (2) CC + (4) + (1) 1OUT (14) (8) 2IN+ 2IN (5) (6) + (7) 2OUT 103 3IN+ 3IN (10) (9) + (8) 3OUT (1) (2) (3) (4) 140 (5) (7) (6) 4IN+ 4IN (12) (13) + (11) CC CHIP THICKNESS: 15 TYPICAL BONDING PADS: 4 4 MINIMUM (14) 4OUT TJmax = 150 C TOLERAES ARE ±10%. ALL DIMENSIONS ARE IN MILS. 6 POST OFFICE BOX DALLAS, TEXAS 75265

7 equivalent schematic CC + R1 Q3 R4 R7 R14 R18 R19 R21 D1 Q5 Q8 Q10 Q13 Q22 Q26 Q30 Q34 Q37 R24 POST OFFICE BOX DALLAS, TEXAS IN IN + OFFSET N1 (see Note A) OFFSET N2 (see Note A) Q1 R2 Q4 Q2 R3 Q6 Q7 R5 C1 R6 Q9 Q11 Q12 NOTE A: OFFSET N1 AND OFFSET N2 are only availiable on the TLE2241x devices. D2 Q14 R8 Q15 Q16 R9 R10 Q17 C2 R11 Q18 CC Q19 R12 Q20 D3 C4 Q21 D4 R13 C3 Q24 ACTUAL DEICE COMPONENT COUNT COMPONENT TLE2241 TLE2242 TLE2244 Transistors Resistors Diodes Capacitors Epi-FET Q23 R15 R16 D5 Q25 Q27 R17 Q28 D6 D7 Q29 D8 Q31 Q32 Q33 R20 R23 Q36 Q35 R22 OUT TLE214x, TLE214xA, TLE214xY

8 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, CC+ (see Note 1) Supply voltage, CC Differential input voltage, ID (see Note 2) ± 44 Input voltage range, I (any input) CC+ to CC 0.3 Input current, I I (each input) ±1 ma Output current, I O ±80 ma Total current into CC ma Total current out of CC ma Duration of short-circuit current at (or below) 25 C (see Note 3) unlimited Continuous total dissipation See Dissipation Rating Table Operating free-air temperature range, T A : C suffix C to 70 C I suffix C to 105 C M suffix C to 125 C Storage temperature range C to 150 C Case temperature for 60 seconds: FK package C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, DW, N, P, or PW package C Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J or JG package C Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between CC+ and CC. 2. Differential voltages are at IN+ with respect to IN. Excessive current flows if input is brought below CC The output may be shorted to either supply. Temperature and /or supply voltages must be limited to ensure that the maximum dissipation rating is not exceeded. DISSIPATION RATING TABLE PACKAGE TA A 25 C DERATING FACTOR TA A = 70 C TA A = 105 C TA A = 125 C POWER RATING ABOE TA = 25 C POWER RATING POWER RATING POWER RATING D 725 mw 5.8 mw/ C 464 mw 261 mw 145 mw DW 1025 mw 8.2 mw/ C 656 mw 369 mw 205 mw FK 1375 mw 11.0 mw/ C 880 mw 495 mw 275 mw J 1375 mw 11.0 mw/ C 880 mw 495 mw 275 mw JG 1050 mw 8.4 mw/ C 672 mw 378 mw 210 mw N 1150 mw 9.2 mw/ C 736 mw 414 mw 230 mw P 1000 mw 8.0 mw/ C 640 mw 360 mw 200 mw PW 525 mw 4.2 mw/ C 336 mw recommended operating conditions C SUFFIX I SUFFIX M SUFFIX MIN MAX MIN MAX MIN MAX Supply voltage, CC± ±2 ±22 ±2 ±22 ±2 ±22 CC = Common-mode mode input voltage, IC CC± = ± Operating free-air temperature, TA C 8 POST OFFICE BOX DALLAS, TEXAS 75265

9 TLE2141C electrical characteristics at specified free-air temperature, CC = 5 (unless otherwise noted) IO αio IIO IIB ICR TLE2141C TLE2141AC PARAMETER TEST CONDITIONS TA MIN TYP MAX MIN TYP MAX Input offset voltage Temperature coefficient of input offset voltage Input offset current Input bias current Common-mode input voltage range O = 2.5 RS = 50 Ω, IC = 2.5 RS =50Ω Ω IOH = 150 µa OH High-level output voltage IOH = 1.5 ma IOH = 15 ma IOL = 150 µa OL Low-level output voltage IOL =15mA 1.5 AD IOL =15mA 25 C Full range µ Full range µ/ C 25 C Full range C Full range C Full range to to C Full range C Full range C Full range C Full range C Full range C Full range Large-signal g differential CC = ±2.5, RL = 2 kω, 25 C voltage amplification O = 1 to 1.5 Full range ri Input resistance 25 C MΩ ci Input capacitance 25 C pf zo Open-loop output impedance f = 1 MHz 25 C Ω Common-mode rejection 25 C CMRR =ICRmin =50Ω ratio IC ICRmin, RS Ω db Full range Supply-voltage rejection CC ± = ±2.5 to ±15, 25 C ksr ratio ( CC± / IO) RS = 50 Ω Full range ICC Supply current Full range is 0 C to 70 C. O O = 2.5, No load, 25 C IC = 2.5 Full range na µa m /m db ma POST OFFICE BOX DALLAS, TEXAS

10 TLE2141C operating characteristics, CC = 5, T A = 25 C PARAMETER TEST CONDITIONS TLE2141C TLE2141AC MIN TYP MAX MIN TYP MAX SR + Positive slew rate AD = 1, RL = 2 kω,, SR Negative slew rate CL = 500 pf, AD = 1, To 0.1% ts Settling time 2.5- step To 0.01% n N(PP) In Equivalent input noise voltage RS = 20 Ω, f = 10 Hz RS = 20 Ω, f = 1 khz Peak-to-peak equivalent input f = 0.1 Hz to 1 Hz noise voltage f = 0.1 Hz to 10 Hz Equivalent input noise current THD+N Total harmonic distortion O = = kω, O 1 to 3, RL 2 plus noise AD = 2, f = 10 khz f = 10 Hz f = 1 khz % 0052% % 0052% /µs µs n/ Hz µ pa/ Hz B1 Unity-gain bandwidth RL = 2 kω, CL = 100 pf MHz BOM Gain-bandwidth product RL = 2 kω, f = 100 khz CL = 100 pf, MHz Maximum output-swing O(PP) = 2, RL = 2 kω, khz bandwidth AD = 1, CL = 100 pf φm Phase margin at unity gain RL = 2 kω, CL = 100 pf RL and CL terminated to POST OFFICE BOX DALLAS, TEXAS 75265

11 TLE2141C electrical characteristics at specified free-air temperature, CC± = ±15 (unless otherwise noted) IO αio IIO IIB ICR TLE2141C TLE2141AC PARAMETER TEST CONDITIONS TA MIN TYP MAX MIN TYP MAX Input offset voltage Temperature coefficient of input offset voltage Input offset current Input bias current Common-mode input voltage range IC = 0, RS = 50 Ω, O = 0 RS =50Ω Ω IO = 150 µa Maximum positive peak OM+ output voltage swing IO = 1.5 ma OM AD Maximum negative peak output voltage swing Large-signal g differential voltage amplification IO = 15 ma IO = 150 µa IO =15mA 1.5 IO =15mA O = ±10 25 C Full range µ Full range µ/ C 25 C Full range C Full range C Full range C Full range C Full range C Full range C Full range C Full range C Full range C Full range ri Input resistance RL = 2 kω 25 C MΩ ci Input capacitance 25 C pf zo Open-loop output impedance CMRR Common-mode =ICRmin =50Ω rejection ratio IC ICRmin, RS Ω ksr IOS Supply-voltage rejection ratio ( CC ± / IO) Short-circuit output current f = 1 MHz 25 C Ω CC ± = ±2.5 to ±15, RS = 50 Ω O = 0 ID = 1 ID = 1 ICC Supply current O = 0, No load Full range is 0 C to 70 C. 25 C Full range C Full range C C Full range na µa /m db db ma ma POST OFFICE BOX DALLAS, TEXAS

12 TLE2141C operating characteristics, CC± = ±15, T A = 25 C PARAMETER TEST CONDITIONS TLE2141C TLE2141AC MIN TYP MAX MIN TYP MAX SR + Positive slew rate AD = 1, RL = 2 kω, SR Negative slew rate CL = 500 pf AD = 1, To 0.1% ts Settling time 10- step To 0.01% n N(PP) In Equivalent input noise voltage RS = 20 Ω, f = 10 Hz RS = 20 Ω, f = 1 khz Peak-to-peak equivalent input f = 0.1 Hz to 1 Hz noise voltage f = 0.1 Hz to 10 Hz Equivalent input noise current THD+N Total harmonic distortion plus = 20, RL = 2 kω, O(PP) noise AD = 10, f = 10 khz f = 10 Hz f = 1 khz % 01% 0.01% 01% B1 Unity-gain bandwidth RL = 2 kω, CL = 100 pf 6 6 MHz BOM RL = 2 kω, Gain-bandwidth product L f = 100 khz CL L = 100 pf, Maximum output-swing O(PP) = 20, RL = 2 kω, bandwidth AD = 1, CL = 100 pf /µs µs n/ Hz µ pa/ Hz MHz khz φm Phase margin at unity gain RL = 2 kω, CL = 100 pf POST OFFICE BOX DALLAS, TEXAS 75265

13 TLE2142C electrical characteristics at specified free-air temperature, CC = 5 (unless otherwise noted) IO αio IIO IIB ICR TLE2142C TLE2142AC PARAMETER TEST CONDITIONS TA MIN TYP MAX MIN TYP MAX Input offset voltage Temperature coefficient of input offset voltage Input offset current Input bias current Common-mode input voltage range O = 2.5, RS = 50 Ω, IC = 2.5 RS =50Ω Ω IOH = 150 µa OH High-level output voltage IOH = 1.5 ma IOH = 15 ma IOL = 150 µa OL Low-level output voltage IOL =15mA 1.5 AD IOL =15mA 25 C Full range µ Full range µ/ C 25 C Full range C Full range C Full range to to C Full range C Full range C Full range C Full range C Full range C Full range Large-signal g differential CC = ±2.5, RL = 2 kω, 25 C voltage amplification O = 1 to 1.5 Full range ri Input resistance 25 C MΩ ci Input capacitance 25 C pf zo Open-loop output impedance f = 1 MHz 25 C Ω Common-mode 25 C CMRR =ICRmin =50Ω rejection ratio IC ICRmin, RS Ω db Full range na µa m /m Supply-voltage rejection CC ± = ±2.5 to ±15, 25 C ksr ratio ( CC± / IO) RS = 50 Ω Full range O = 2.5, No load, 25 C ICC Supply current IC = 2.5 Full range Full range is 0 C to 70 C. db ma POST OFFICE BOX DALLAS, TEXAS

14 TLE2142C operating characteristics, CC = 5, T A = 25 C PARAMETER TEST CONDITIONS TLE2142C TLE2142AC MIN TYP MAX MIN TYP MAX SR + Positive slew rate = = kω, AD 1, RL 2 SR Negative slew rate CL = 500 pf AD = 1, To 0.1% ts Settling time 2.5- step To 0.01% n N(PP) In Equivalent input noise voltage RS = 20 Ω, f = 10 Hz RS = 20 Ω, f = 1 khz Peak-to-peak equivalent f = 0.1 Hz to 1 Hz input noise voltage f = 0.1 Hz to 10 Hz Equivalent input noise current THD+N Total harmonic distortion plus = 1 to 3, O RL = 2 kω, noise AD = 2, f = 10 khz f = 10 Hz f = 1 khz % 0052% % 0052% B1 Unity-gain bandwidth RL = 2 kω, CL = 100 pf MHz BOM Gain-bandwidth product RL = 2 kω, f = 100 khz CL = 100 pf, Maximum output-swing O(PP) = 2, RL = 2 kω, bandwidth AD = 1, CL = 100 pf /µs µs n/ Hz µ pa/ Hz MHz khz φm Phase margin at unity gain RL = 2 kω, CL = 100 pf RL terminates at POST OFFICE BOX DALLAS, TEXAS 75265

15 TLE2142C electrical characteristics at specified free-air temperature, CC± = ±15 (unless otherwise noted) IO αio IIO IIB ICR TLE2142C TLE2142AC PARAMETER TEST CONDITIONS TA MIN TYP MAX MIN TYP MAX Input offset voltage Temperature coefficient of input offset voltage Input offset current Input bias current Common-mode input voltage range IC = 0, RS = 50 Ω, O = 0 RS =50Ω Ω IO = 150 µa Maximum positive peak OM+ output voltage swing IO = 1.5 ma OM AD Maximum negative peak output voltage swing Large-signal g differential voltage amplification IO = 15 ma IO = 150 µa IO =15mA 1.5 IO =15mA O = ±10 25 C Full range µ Full range µ/ C 25 C Full range C Full range C Full range C Full range C Full range C Full range C Full range C Full range C Full range C Full range ri Input resistance RL = 2 kω 25 C MΩ ci Input capacitance 25 C pf zo Open-loop output impedance f = 1 MHz 25 C Ω Common-mode = ICRmin, 25 C CMRR IC rejection ratio RS = 50 Ω Full range ksr Supply-voltage rejection CC ± = ± 2.5 to ±15, 25 C ratio ( CC± / IO) RS = 50 Ω Full range IOS Short-circuit output current O =0 ID = 1 ID = 1 ICC Supply current O =0 0, No load Full range is 0 C to 70 C. 25 C C Full range na µa /m db db ma ma POST OFFICE BOX DALLAS, TEXAS

16 TLE2142C operating characteristics, CC± = ±15, T A = 25 C PARAMETER TEST CONDITIONS TLE2142C TLE2142AC MIN TYP MAX MIN TYP MAX SR + Positive slew rate AD = 1, RL = 2 kω, SR Negative slew rate CL = 500 pf AD = 1, To 0.1% ts Settling time 10- step To 0.01% n N(PP) In Equivalent input noise voltage RS = 20 Ω, f = 10 Hz RS = 20 Ω, f = 1 khz Peak-to-peak equivalent input f = 0.1 Hz to 1 Hz noise voltage f = 0.1 Hz to 10 Hz Equivalent input noise current THD+N Total harmonic distortion plus = 20, RL = 2 kω, O(PP), noise AD = 10, f = 10 khz f = 10 Hz f = 1 khz % 01% 0.01% 01% B1 Unity-gain bandwidth RL = 2 kω, CL = 100 pf 6 6 MHz BOM RL = 2 kω,, Gain-bandwidth product L f =100 khz CL L = 100 pf, Maximum output-swing O(PP) = 20, RL = 2 kω,, bandwidth AD = 1, CL = 100 pf /µs µs n/ Hz µ pa/ Hz MHz khz φm Phase margin at unity gain RL = 2 kω, CL = 100 pf POST OFFICE BOX DALLAS, TEXAS 75265

17 TLE2144C electrical characteristics at specified free-air temperature, CC = 5 (unless otherwise noted) IO αio IIO IIB ICR OH OL AD TLE2144C TLE2144AC PARAMETER TEST CONDITIONS TA MIN TYP MAX MIN TYP MAX Input offset voltage Temperature coefficient of input offset voltage O = 2.5, Input offset current IC = 2.5 Input bias current Common-mode input voltage range High-level output voltage Low-level output voltage RS =50Ω Ω IOH = 150 µa IOH = 1.5 ma IOH = 15 ma IOL = 150 µa IOL =15mA 1.5 IOL =15mA RS = 50 Ω, 25 C Full range m Full range µ/ C 25 C Full range C Full range C Full range C Full range C Full range C Full range C Full range C Full range C Full range Large-signal g differential CC = ±2.5, RL L = 2 kω, 25 C voltage amplification O = 1 to 1.5 Full range ri Input resistance 25 C MΩ ci Input capacitance 25 C pf zo Open-loop output impedance CMRR Common-mode =ICRmin =50Ω rejection ratio IC ICRmin, RS Ω ksr ICC Supply-voltage rejection ratio ( CC ± / IO) Supply current Full range is 0 C to 70 C. f = 1 MHz 25 C Ω CC ± = ±2.5 to ±15, RS = 50 Ω 25 C Full range C Full range O O = 2.5, No load, 25 C IC = 2.5 Full range na µa m /m db db ma POST OFFICE BOX DALLAS, TEXAS

18 TLE2144C operating characteristics, CC = 5, T A = 25 C TLE2144C TLE2144AC PARAMETER TEST CONDITIONS MIN TYP MAX MIN TYP MAX SR + Positive slew rate AD = 1, RL L = 2 kω, SR Negative slew rate CL = 500 pf AD = 1, To 0.1% ts Settling time 2.5- step To 0.01% n Equivalent input RS = 20 Ω, f = 10 Hz noise voltage RS = 20 Ω, f = 1 khz N(PP) Peak-to-peak equivalent f = 0.1 Hz to 1 Hz input noise voltage f = 0.1 Hz to 10 Hz In Equivalent input f = 10 Hz noise current f = 1 khz /µs µs n/ Hz µ pa/ Hz THD+N Total harmonic distortion plus = 1 to 3, RL = 2 kω, O % 0052% % 0052% noise AD = 2, f = 10 khz B1 Unity-gain bandwidth RL = 2 kω, CL = 100 pf MHz RL = 2 kω, CL = 100 pf, Gain-bandwidth product MHz f = 100 khz Maximum output-swing O(PP) = 2, RL = 2 kω, BOM khz bandwidth AD = 1, CL = 100 pf φm Phase margin at unity gain RL = 2 kω, CL = 100 pf RL terminates at POST OFFICE BOX DALLAS, TEXAS 75265

19 TLE2144C electrical characteristics at specified free-air temperature, CC± = ±15 (unless otherwise noted) IO αio IIO IIB ICR TLE2144C TLE2144AC PARAMETER TEST CONDITIONS TA MIN TYP MAX MIN TYP MAX Input offset voltage Temperature coefficient of input offset voltage IC = 0, RS = 50 Ω, Input offset current O = 0 Input bias current Common-mode input voltage range RS =50Ω Ω IO = 150 µa Maximum positive peak OM+ output voltage swing IO = 1.5 ma OM AD Maximum negative peak output voltage swing Large-signal g differential voltage amplification IO = 15 ma IO = 150 µa IO =15mA 1.5 IO =15mA O = ±10 25 C Full range m Full range µ/ C 25 C Full range C Full range C Full range C Full range C Full range C Full range C Full range C Full range C Full range C Full range ri Input resistance RL = 2 kω 25 C MΩ ci Input capacitance 25 C pf zo Open-loop output impedance CMRR Common-mode =ICRmin =50Ω rejection ratio IC ICRmin, RS Ω ksr IOS Supply-voltage rejection ratio ( CC ± / IO) Short-circuit output current f = 1 MHz 25 C Ω CC ± = ±2.5 to ±15, RS = 50 Ω O =0 ID = 1 ID = 1 ICC Supply current O =0 0, No load Full range is 0 C to 70 C. 25 C Full range C Full range C C Full range na µa /m db db ma ma POST OFFICE BOX DALLAS, TEXAS

20 TLE2144C operating characteristics, CC± = ±15, T A = 25 C PARAMETER TEST CONDITIONS TLE2144C TLE2144AC MIN TYP MAX MIN TYP MAX SR + Positive slew rate AD = 1, RL = 2 kω, SR Negative slew rate CL = 500 pf AD = 1, To 0.1% ts Settling time 10- step To 0.01% n N(PP) In Equivalent input noise voltage RS = 20 Ω, f = 10 Hz RS = 20 Ω, f = 1 khz Peak-to-peak equivalent input f = 0.1 Hz to 1 Hz noise voltage f = 0.1 Hz to 10 Hz Equivalent input noise current THD+N Total harmonic distortion plus = 20, RL = 2 kω, O(PP) noise AD = 10, f = 10 khz f = 10 Hz f = 1 khz % 01% 0.01% 01% B1 Unity-gain bandwidth RL = 2 kω, CL = 100 pf 6 6 MHz BOM RL = 2 kω, Gain-bandwidth product L f = 100 khz CL L = 100 pf, Maximum output-swing O(PP) = 20, RL = 2 kω, bandwidth AD = 1, CL = 100 pf /µs µs n/ Hz µ pa/ Hz MHz khz φm Phase margin at unity gain RL = 2 kω, CL = 100 pf POST OFFICE BOX DALLAS, TEXAS 75265

21 TLE2141I electrical characteristics at specified free-air temperature, CC = 5 (unless otherwise noted) IO αio IIO IIB ICR OH OL AD TLE2141I TLE2141AI PARAMETER TEST CONDITIONS TA MIN TYP MAX MIN TYP MAX Input offset voltage Temperature coefficient of input offset voltage Input offset current Input bias current Common-mode input voltage range High-level output voltage Low-level output voltage O = 2.5, RS = 50 Ω, IC = 2.5 RS =50Ω Ω 25 C Full range µ Full range µ/ C 25 C Full range C Full range C Full range IOH = 150 µa IOH = 1.5 ma 25 C IOH = 15 ma IOH = 100 µa IOH = 1 ma Full range IOH = 10 ma IOL = 150 µa IOL = 1.5 µa 25 C IOL = 15 ma IOL = 100 µa IOL = 1 ma Full range IOL = 10 ma Large-signal g differential CC = ±2.5, RL L = 2 kω, 25 C voltage amplification O = 1 to 1.5 Full range ri Input resistance 25 C MΩ ci Input capacitance 25 C pf zo Open-loop output impedance CMRR Common-mode =ICRmin =50Ω rejection ratio IC ICRmin, RS Ω f = 1 MHz 25 C Ω 25 C Full range Supply-voltage rejection CC ± = ±2.5 to ±15, 25 C ksr ratio ( CC± / IO) RS = 50 Ω Full range ICC Supply current Full range is 40 C to 105 C. O O = 2.5, No load, 25 C IC = 2.5 Full range na µa m m /m db db ma POST OFFICE BOX DALLAS, TEXAS

22 TLE2141I operating characteristics, CC = 5, T A = 25 C PARAMETER TEST CONDITIONS TLE2141I TLE2141AI MIN TYP MAX MIN TYP MAX SR + Positive slew rate = = kω, AD 1, RL 2 SR Negative slew rate CL = 500 pf AD = 1, To 0.1% ts Settling time 2.5- step To 0.01% n N(PP) In Equivalent input noise voltage RS = 20 Ω, f = 10 Hz RS = 20 Ω, f = 1 khz Peak-to-peak equivalent input f = 0.1 Hz to 1 Hz noise voltage f = 0.1 Hz to 10 Hz Equivalent input noise current THD+N Total harmonic distortion plus O = O 1 to 3, RL = 2 kω, noise AD = 2, f = 10 khz f = 10 Hz f = 1 khz % 0052% % 0052% B1 Unity-gain bandwidth RL = 2 kω, CL = 100 pf MHz BOM Gain-bandwidth product Maximum output-swing bandwidth RL = 2 kω f = 100 khz O(PP) = 2, AD = 1, CL = 100 pf, /µs µs n/ Hz µ pa/ Hz MHz RL = 2 kω, CL = 100 pf khz φm Phase margin at unity gain RL = 2 kω, CL = 100 pf RL and CL terminated to POST OFFICE BOX DALLAS, TEXAS 75265

23 TLE2141I electrical characteristics at specified free-air temperature, CC± = ±15 (unless otherwise noted) IO αio IIO IIB ICR TLE2141I TLE2141AI PARAMETER TEST CONDITIONS TA MIN TYP MAX MIN TYP MAX Input offset voltage Temperature coefficient of input offset voltage Input offset current Input bias current Common-mode input voltage range IC = 0, RS = 50 Ω, O = 0 RS =50Ω Ω 25 C Full range µ Full range µ/ C 25 C Full range C Full range C Full range IO = 150 µa IO = 1.5 A 25 C Maximum positive peak IO = 15 ma OM+ output voltage swing IO = 100 µa OM AD IO = 1 ma Full range IO = 10 ma IO = 150 µa IO = 1.5 ma 25 C Maximum negative peak IO = 15 ma output voltage swing IO = 100 µa Large-signal g differential voltage amplification IO = 1 ma Full range IO = 10 ma O = ±10, RL =2kΩ 25 C Full range ri Input resistance 25 C MΩ ci Input capacitance 25 C pf zo Open-loop output impedance CMRR Common-mode =ICRmin =50Ω rejection ratio IC ICRmin, RS Ω f = 1 MHz 25 C Ω 25 C Full range Supply-voltage rejection CC ± = ±2.5 to ±15, 25 C ksr ratio ( CC± / IO) RS = 50 Ω Full range IOS Short-circuit output current O =0 ID = 1 ID = 1 ICC Supply current O =0 0, No load Full range is 40 C to 105 C. 25 C C Full range na µa /m db db ma ma POST OFFICE BOX DALLAS, TEXAS

24 TLE2141I operating characteristics, CC± = ±15, T A = 25 C PARAMETER TEST CONDITIONS TLE2141I TLE2141AI MIN TYP MAX MIN TYP MAX SR + Positive slew rate AD = 1, RL = 2 kω, SR Negative slew rate CL = 500 pf AD = 1, To 0.1% ts Settling time 10- step To 0.01% n N(PP) In Equivalent input noise voltage RS = 20 Ω, f = 10 Hz RS = 20 Ω, f = 1 khz Peak-to-peak equivalent input f = 0.1 Hz to 1 Hz noise voltage f = 0.1 Hz to 10 Hz Equivalent input noise current THD+N Total harmonic distortion plus = 20, RL = 2 kω, O(PP) noise AD = 10, f = 10 khz f = 10 Hz f = 1 khz % 01% 0.01% 01% /µs µs n/ Hz µ pa/ Hz B1 Unity-gain bandwidth RL = 2 kω, CL = 100 pf 6 6 MHz BOM RL = 2 kω, Gain-bandwidth product L f = 100 khz CL L = 100 pf, Maximum output-swing O(PP) = 20, RL = 2 kω, bandwidth AD = 1, CL = 100 pf MHz khz φm Phase margin at unity gain RL = 2 kω, CL = 100 pf POST OFFICE BOX DALLAS, TEXAS 75265

25 TLE2142I electrical characteristics at specified free-air temperature, CC = 5 (unless otherwise noted) IO αio IIO IIB ICR OH OL AD TLE2142I TLE2142AI PARAMETER TEST CONDITIONS TA MIN TYP MAX MIN TYP MAX Input offset voltage Temperature coefficient of input offset voltage Input offset current Input bias current Common-mode input voltage range High-level output voltage Low-level output voltage O = 2.5, RS = 50 Ω, IC = 2.5 RS =50Ω Ω 25 C Full range µ Full range µ/ C 25 C Full range C Full range C Full range IOH = 150 µa IOH = 1.5 ma 25 C IOH = 15 ma IOH = 100 µa IOH = 1 ma Full range IOH = 10 ma IOl = 150 µa IOL = 1.5 ma 25 C IOL = 15 ma IOL = 100 µa IOL = 1 ma Full range IOL = 10 ma Large-signal g differential IC = ±2.5, RL = 2 kω, 25 C voltage amplification O = 1 to 1.5 Full range ri Input resistance 25 C MΩ ci Input capacitance 25 C pf zo Open-loop output impedance f = 1 MHz 25 C Ω Common-mode rejection 25 C CMRR =ICRmin =50Ω ratio IC ICRmin, RS Ω db Full range Supply-voltage rejection CC ± = ±2.5 to ±15, 25 C ksr ratio ( CC± / IO) RS = 50 Ω Full range ICC Supply current Full range is 40 C to 105 C. O O = 2.5, No load, 25 C IC = 2.5 Full range na µa m m /m db ma POST OFFICE BOX DALLAS, TEXAS

26 TLE2142I operating characteristics, CC = 5, T A = 25 C PARAMETER TEST CONDITIONS TLE2142I TLE2142AI MIN TYP MAX MIN TYP MAX SR + Positive slew rate = = kω, AD 1, RL 2 SR Negative slew rate CL = 500 pf AD = 1, To 0.1% ts Settling time 2.5- step To 0.01% n Equivalent input noise RS = 20 Ω, f = 10 Hz voltage RS = 20 Ω, f = 1 khz /µs µs n/ Hz N(PP) In Peak-to-peak equivalent input f = 0.1 Hz to 1 Hz noise voltage f = 0.1 Hz to 10 Hz Equivalent input noise f = 10 Hz current f = 1 khz µ pa/ Hz THD+N Total harmonic distortion O O = 1 to 3, RL = 2 kω, % 0052% % 0052% plus noise AD = 2, f = 10 khz B1 Unity-gain bandwidth RL = 2 kω, CL = 100 pf MHz Gain-bandwidth product RL = 2 kω, CL = 100 pf, MHz f = 100 khz Maximum output-swing O(PP) = 2, RL L = 2 kω, BOM khz bandwidth AD = 1, CL = 100 pf φm Phase margin at unity gain RL = 2 kω, CL = 100 pf RL terminates at POST OFFICE BOX DALLAS, TEXAS 75265

27 TLE2142I electrical characteristics at specified free-air temperature, CC± = ±15 (unless otherwise noted) IO αio IIO IIB ICR TLE2142I TLE2142I PARAMETER TEST CONDITIONS TA MIN TYP MAX MIN TYP MAX Input offset voltage Temperature coefficient of input offset voltage Input offset current Input bias current Common-mode input voltage range IC = 0, RS = 50 Ω, O = 0 RS =50Ω Ω 25 C Full range µ Full range µ/ C 25 C Full range C Full range C Full range IO = 150 µa IO = 1.5 ma 25 C Maximum positive peak IO = 15 ma OM+ output voltage swing IO = 100 µa OM AD IO = 1 ma Full range IO = 10 ma IO = 150 µa IO = 1.5 ma 25 C Maximum negative peak IO = 15 ma output voltage swing IO = 100 µa Large-signal g differential voltage amplification IO = 1 ma Full range IO = 10 ma O = ±10, RL =2kΩ 25 C Full range ri Input resistance 25 C MΩ ci Input capacitance 25 C pf zo Open-loop output impedance f = 1 MHz 25 C Ω Common-mode rejection IC = ICRmin 25 C CMRR ratio RS = 50 Ω Full range Supply-voltage rejection CC ± = ±2.5 to ± 15, 25 C ksr ratio ( CC± / IO) RS = 50 Ω Full range IOS Short-circuit output current O =0 ID = 1 ID = 1 ICC Supply current O =0 0, No load Full range is 40 C to 105 C. 25 C C Full range na µa /m db db ma ma POST OFFICE BOX DALLAS, TEXAS

28 TLE2142I operating characteristics, CC± = ±15, T A = 25 C PARAMETER TEST CONDITIONS TLE2142I TLE2142AI MIN TYP MAX MIN TYP MAX SR + Positive slew rate AD = 1, RL = 2 kω, SR Negative slew rate CL = 500 pf AD = 1, To 0.1% ts Settling time 10- step To 0.01% n N(PP) In Equivalent input noise voltage RS = 20 Ω, f = 10 Hz RS = 20 Ω, f = 1 khz Peak-to-peak equivalent input f = 0.1 Hz to 1 Hz noise voltage f = 0.1 Hz to 10 Hz Equivalent input noise current THD+N Total harmonic distortion plus = 20, RL = 2 kω, O(PP), noise AD = 10, f = 10 khz f = 10 Hz f = 1 khz % 01% 0.01% 01% B1 Unity-gain bandwidth RL = 2 kω, CL = 100 pf 6 6 MHz BOM RL = 2 kω, Gain-bandwidth product L f =100 khz CL L = 100 pf, Maximum output-swing O(PP) = 20, RL = 2 kω,, bandwidth AD = 1, CL = 100 pf /µs µs n/ Hz µ pa/ Hz MHz khz φm Phase margin at unity gain RL = 2 kω, CL = 100 pf POST OFFICE BOX DALLAS, TEXAS 75265

29 TLE2144I electrical characteristics at specified free-air temperature, CC = 5 (unless otherwise noted) IO αio IIO IIB ICR OH OL AD TLE2144I TLE2144AI PARAMETER TEST CONDITIONS TA MIN TYP MAX MIN TYP MAX Input offset voltage Temperature coefficient of input offset voltage IC = 0, RS = 50 Ω, Input offset current O = 0 Input bias current Common-mode input voltage range RS =50Ω Ω 25 C Full range m Full range µ/ C 25 C Full range C Full range C Full range IOH = 150 µa IOH = 1.5 ma 25 C High-level IOH = 15 ma output voltage IOH = 100 µa IOH = 1 ma Full range IOH = 10 ma IOL = 150 µa IOL = 1.5 µa 25 C Low-level IOL = 15 ma output voltage IOL = 100 µa m IOL = 1 ma Full range IOL = 10 ma Large-signal g differential IC = ±2.5, RL = 2 kω, 25 C voltage amplification O = 1 to 1.5 Full range ri Input resistance 25 C MΩ ci Input capacitance 25 C pf zo Open-loop output impedance f = 1 MHz 25 C Ω Common-mode 25 C CMRR =ICRmin =50Ω rejection ratio IC ICRmin, RS Ω db Full range na µa m /m ksr ICC Supply-voltage rejection ratio ( CC ± / IO) Supply current Full range is 40 C to 105 C. CC ± = ±2.5 to ±15, 25 C RS = 50 Ω Full range O O = 2.5, No load, 25 C IC = 2.5 Full range db ma POST OFFICE BOX DALLAS, TEXAS

30 TLE2144I operating characteristics, CC = 5, T A = 25 C PARAMETER TEST CONDITIONS TLE2144I TLE2144AI MIN TYP MAX MIN TYP MAX SR + Positive slew rate AD = 1, = kω, RL 2 SR Negative slew rate CL = 500 pf AD = 1, To 0.1% ts Settling time 2.5- step To 0.01% n N(PP) In Equivalent input noise voltage RS = 20 Ω, f = 10 Hz RS = 20 Ω, f = 1 khz Peak-to-peak equivalent input f = 0.1 Hz to 1 Hz noise voltage f = 0.1 Hz to 10 Hz Equivalent input noise current THD+N Total harmonic distortion plus = 1 to 3, RL = 2 kω, O noise AD = 2, f = 10 khz f = 10 Hz f = 10 khz % 0052% % 0052% B1 Unity-gain bandwidth RL = 2 kω, CL = 100 pf MHz BOM RL = 2 kω, Gain-bandwidth product f = 100 khz CL = 100 pf, Maximum output-swing O(PP) = 2, RL = 2 kω, bandwidth AD = 1, CL = 100 pf /µs µs n/ Hz µ pa/ Hz MHz khz φm Phase margin at unity gain RL = 2 kω, CL = 100 pf RL terminates at POST OFFICE BOX DALLAS, TEXAS 75265

31 TLE2144I electrical characteristics at specified free-air temperature, CC± = ±15 (unless otherwise noted) IO αio IIO IIB ICR TLE2144I TLE2144AI PARAMETER TEST CONDITIONS TA MIN TYP MAX MIN TYP MAX Input offset voltage Temperature coefficient of input offset voltage IC = 0, RS = 50 Ω, Input offset current O = 0 Input bias current Common-mode input voltage range RS =50Ω Ω 25 C Full range m Full range µ/ C 25 C Full range C Full range C Full range IO = 150 µa IO = 1.5 A 25 C Maximum positive peak IO = 15 ma OM+ output voltage swing IO = 100 µa OM AD Maximum negative peak output voltage swing Large-signal g differential voltage amplification IO = 1 ma Full range IO = 10 ma IO = 150 µa IO = 1.5 ma 25 C IO = 15 ma IO = 100 µa IO = 1 ma Full range IO = 10 ma O = ±10, RL =2kΩ 25 C Full range ri Input resistance 25 C MΩ ci Input capacitance 25 C pf zo Open-loop output impedance CMRR Common-mode =ICRmin =50Ω rejection ratio IC ICRmin, RS Ω ksr IOS Supply-voltage rejection ratio ( CC ± / IO) Short-circuit output current f = 1 MHz 25 C Ω CC ± = ±2.5 to ±15, RS = 50 Ω O =0 ID = 1 ID = 1 ICC Supply current O =0 0, No load Full range is 40 C to 105 C. 25 C Full range C Full range C C Full range na µa /m db db ma ma POST OFFICE BOX DALLAS, TEXAS

32 TLE2144I operating characteristics, CC± = ±15, T A = 25 C PARAMETER TEST CONDITIONS TLE2144I TLE2144AI MIN TYP MAX MIN TYP MAX SR + Positive slew rate AD = 1, RL = 2 kω, SR Negative slew rate CL = 500 pf AD = 1, To 0.1% ts Settling time 10- step To 0.01% n N(PP) In Equivalent input RS = 20 Ω, f = 10 Hz noise voltage RS = 20 Ω, f = 1 khz Peak-to-peak equivalent f = 0.1 Hz to 1 Hz input noise voltage f = 0.1 Hz to 10 Hz Equivalent input f = 10 Hz noise current f = 1 khz THD+N Total harmonic distortion plus = 20, RL = 2 kω, O(PP) noise AD = 10, f = 10 khz 0.01% 01% 0.01% 01% B1 Unity-gain bandwidth RL = 2 kω, CL = 100 pf 6 6 MHz BOM RL = 2 kω, Gain-bandwidth product L f = 100 khz CL L = 100 pf, Maximum output-swing O(PP) = 20, RL = 2 kω, bandwidth AD = 1, CL = 100 pf /µs µs n/ Hz µ pa/ Hz MHz khz φm Phase margin at unity gain RL = 2 kω, CL = 100 pf POST OFFICE BOX DALLAS, TEXAS 75265

33 TLE2141M electrical characteristics at specified free-air temperature, CC = 5 (unless otherwise noted) IO αio IIO IIB ICR OH TLE2141M TLE2141AM PARAMETER TEST CONDITIONS TA MIN TYP MAX MIN TYP MAX Input offset voltage Temperature coefficient of input offset voltage Input offset current Input bias current Common-mode input voltage range O = 2.5 RS = 50 Ω, IC = 2.5 RS =50Ω Ω 25 C Full range µ Full range µ/ C 25 C Full range C Full range C Full range IOH = 150 µa IOH = 1.5 ma 25 C High-level output IOH = 15 ma voltage IOH = 100 µa IOH = 1 ma Full range IOH = 10 ma IOL = 150 µa IOL = 1.5 µa 25 C Low-level output IOL = 15 ma OL voltage IOL = 100 µa m IOL = 1 ma Full range AD IOL = 10 ma Large-signal g differential IC = ±2.5, RL L = 2 kω,, 25 C voltage amplification O = 1 to 1.5 Full range 5 5 ri Input resistance 25 C MΩ ci Input capacitance 25 C pf zo Open-loop output impedance CMRR Common-mode =ICRmin =50Ω rejection ratio IC ICRmin, RS Ω f = 1 MHz 25 C Ω 25 C Full range Supply-voltage rejection CC ± = ±2.5 to ±15, 25 C ksr ratio ( CC± / IO) RS = 50 Ω Full range ICC Supply current Full range is 55 C to 125 C. O O = 2.5, No load, 25 C IC = 2.5 Full range na µa m /m db db ma POST OFFICE BOX DALLAS, TEXAS

34 TLE2141M operating characteristics, CC = 5, T A = 25 C PARAMETER TEST CONDITIONS TLE2141M TLE2141AM MIN TYP MAX MIN TYP MAX SR + Positive slew rate = = kω, AD 1, RL 2 SR Negative slew rate CL = 500 pf AD = 1, To 0.1% ts Settling time 2.5- step To 0.01% n N(PP) In THD + N Equivalent input noise voltage RS = 20 Ω, f = 10 Hz RS = 20 Ω, f = 1 khz Peak-to-peak equivalent input f = 0.1 Hz to 1 Hz noise voltage f = 0.1 Hz to 10 Hz Equivalent input noise current Total harmonic distortion plus noise f = 10 Hz f = 1 khz O = 1 to 3, AD = 2, RL = 2 kω, f = 10 khz % % /µs µs n/ Hz µ pa/ Hz B1 Unity-gain bandwidth RL = 2 kω, CL = 100 pf MHz Gain-bandwidth product RL = 2 kω, f = 100 khz CL = 100 pf, MHz BOM Maximum output-swing bandwidth O(PP) = 2, AD = 1 RL = 2 kω, khz φm Phase margin at unity gain RL = 2 kω, CL = 100 pf RL and CL terminated to POST OFFICE BOX DALLAS, TEXAS 75265

35 TLE2141M electrical characteristics at specified free-air temperature, CC± = ±15 (unless otherwise noted) IO αio IIO IIB ICR TLE2141M TLE2141AM PARAMETER TEST CONDITIONS TA MIN TYP MAX MIN TYP MAX Input offset voltage Temperature coefficient of input offset voltage Input offset current Input bias current Common-mode input voltage range IC = 0, RS = 50 Ω RS =50Ω Ω 25 C Full range µ Full range µ/ C 25 C Full range C Full range C Full range IO = 150 µa IO = 1.5 A 25 C Maximum positive peak IO = 15 ma OM+ output voltage swing IO = 100 µa OM AD IO = 1 ma Full range IO = 10 ma IO = 150 µa IO = 1.5 ma 25 C Maximum negative peak IO = 15 ma output voltage swing IO = 100 µa Large-signal g differential voltage amplification IO = 1 ma Full range IO = 10 ma O = ±10, RL =2kΩ 25 C Full range ri Input resistance 25 C MΩ ci Input capacitance 25 C pf zo Open-loop output impedance CMRR Common-mode =ICRmin =50Ω rejection ratio IC ICRmin, RS Ω f = 1 MHz 25 C Ω 25 C Full range Supply-voltage rejection CC ± = ±2.5 to ±15, 25 C ksr ratio ( CC± / IO) RS = 50 Ω Full range IOS ICC Short-circuit output current Supply current Full range is 55 C to 125 C. O = 0 ID = 1 ID = 1 25 C O O = 0, No load, 25 C IC = 2.5 Full range na µa /m db db ma ma POST OFFICE BOX DALLAS, TEXAS

36 TLE2141M operating characteristics, CC± = ±15, T A = 25 C PARAMETER TEST CONDITIONS TLE2141M TLE2141AM MIN TYP MAX MIN TYP MAX SR + Positive slew rate AD = 1, RL = 2 kω, SR Negative slew rate CL = 100 pf AD = 1, To 0.1% ts Settling time 10- step To 0.01% n N(PP) In Equivalent input noise voltage RS = 20 Ω, f = 10 Hz RS = 20 Ω, f = 1 khz Peak-to-peak equivalent input f = 0.1 Hz to 1 Hz noise voltage f = 0.1 Hz to 10 Hz Equivalent input noise current THD+N Total harmonic distortion plus = 20, RL = 2 kω, O(PP) noise AD = 10, f = 10 khz f = 10 Hz f = 1 khz % 01% 0.01% 01% /µs µs n/ Hz µ pa/ Hz B1 Unity-gain bandwidth RL = 2 kω, CL = 100 pf 6 6 MHz BOM RL = 2 kω, Gain-bandwidth product L f = 100 khz CL L = 100 pf, Maximum output-swing O(PP) = 20, RL = 2 kω, bandwidth AD = 1, CL = 100 pf MHz khz φm Phase margin at unity gain RL = 2 kω, CL = 100 pf POST OFFICE BOX DALLAS, TEXAS 75265