Low Noise, High Speed Amplifier for 16-Bit Systems AD8021
|
|
- Kelly Joseph
- 5 years ago
- Views:
Transcription
1 Low Noise, High Speed Amplifier for -Bit Systems AD FEATURES Low noise. nv/ Hz input voltage noise. pa/ Hz input current noise Custom compensation Constant bandwidth from G = to G = High speed MHz (G = ) 9 MHz (G = ) Low power 4 mw or.7 ma typical for V supply Output disable feature,. ma Low distortion 9 dbc second harmonic, fc = MHz dbc third harmonic, fc = MHz DC precision mv maximum input offset voltage. µv/ C input offset voltage drift Wide supply range, V to 4 V Low price Small packaging Available in SOIC- and MSOP- APPLICATIONS ADC preamp and driver Instrumentation preamp Active filters Portable instrumentation Line receivers Precision instruments Ultrasound signal processing High gain circuits PRODUCT DESCRIPTION The AD is an exceptionally high performance, high speed voltage feedback amplifier that can be used in -bit resolution systems. It is designed to have both low voltage and low current noise (. nv/ Hz typical and. pa/ Hz typical) while operating at the lowest quiescent supply current (7 ± V) among today s high speed, low noise op amps. The AD operates over a wide range of supply voltages from. V to V, as well as from single V supplies, making it ideal for high speed, low power instruments. An output disable pin allows further reduction of the quiescent supply current to. ma. CONNECTION DIAGRAM LOGIC REFERENCE IN +IN 4 AD 7 DISABLE V OUT C COMP Figure. SOIC- (R-) and MSOP- (RM-) The AD allows the user to choose the gain bandwidth product that best suits the application. With a single capacitor, the user can compensate the AD for the desired gain with little trade-off in bandwidth. The AD is a very well behaved amplifier that settles to.% in ns for a V step. It has a fast overload recovery of ns. The AD is stable over temperature with low input offset voltage drift and input bias current drift,. µv/ C and na/ C, respectively. The AD is also capable of driving a 7 Ω line with ± V video signals. The AD is both technically superior and priced considerably less than comparable amps drawing much higher quiescent current. The AD is a high speed, general-purpose amplifier, ideal for a wide variety of gain configurations, and can be used throughout a signal processing chain and in control loops. The AD is available in both standard -lead SOIC and MSOP packages in the industrial temperature range of 4 C to + C. CLOSED-LOOP 4 9 V OUT = mv p-p G =, R F = kω, R G = Ω, R IN = Ω, C C = pf G =, R F = kω, R G = Ω, R IN =.Ω, C C =.pf G =, R F =, R G = 49Ω, R IN =.4Ω, C C = 4pF G =, R F =, R G =, R IN =.Ω, C C = 7pF.M M M M G Figure. Small Signal Frequency Response - - Rev. E Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9, Norwood, MA -9, U.S.A. Tel: Fax: 7.4. Analog Devices, Inc. All rights reserved.
2 AD TABLE OF CONTENTS Specifications... Absolute Maximum Ratings... 7 Maximum Power Dissipation... 7 ESD Caution... 7 Pin Configuration and Function Descriptions... Typical Performance Characteristics... 9 Test Circuits... 7 Applications... 9 Theory of Operation... PCB Layout Considerations... Driving -Bit ADCs... Differential Driver... Using the AD in Active Filters... Driving Capacitive Loads... Outline Dimensions... Ordering Guide... Using the Disable Feature... REVISION HISTORY / Rev. D to Rev. E Updated Format...Universal Change to Figure 9... Change to Figure... Change to Table 7 and Table... Change to Driving -Bit ADCs Section... / Data Sheet Changed from Rev. C to Rev. D. Updated format...universal 7/ Data Sheet Changed from Rev. B to Rev. C. Deleted all references to evaluation board...universal Replaced Figure... Updated OUTLINE DIMENSIONS... / Data Sheet Changed from Rev. A to Rev. B. Edits to Evaluation Board Applications... Edits to Figure 7... / Data Sheet Changed from Rev. to Rev. A. Edits to SPECIFICATIONS... Rev. E Page of
3 SPECIFICATIONS VS = ± TA = C, RL = kω, gain = +, unless otherwise noted. Rev. E Page of AD Table. ADAR/ADARM Parameter Conditions Min Typ Max Unit DYNAMIC PERFORMANCE db Small Signal Bandwidth G = +, CC = pf, VO =. V p-p 49 MHz G = +, CC = 7 pf, VO =. V p-p MHz G = +, CC = pf, VO =. V p-p MHz G = +, CC = pf, VO =. V p-p MHz Slew Rate, V Step G = +, CC = pf 9 V/µs G = +, CC = 7 pf V/µs G = +, CC = pf V/µs G = +, CC = pf 4 V/µs Settling Time to.% VO = V step, RL = Ω ns Overload Recovery (%) ±. V input step, G = + ns DISTORTION/NOISE PERFORMANCE f = MHz HD VO = V p-p 9 dbc HD VO = V p-p dbc f = MHz HD VO = V p-p 7 dbc HD VO = V p-p dbc Input Voltage Noise f = khz.. nv/ Hz Input Current Noise f = khz. pa/ Hz Differential Gain Error NTSC, RL = Ω. % Differential Phase Error NTSC, RL = Ω.4 Degrees DC PERFORMANCE Input Offset Voltage.4. mv Input Offset Voltage Drift TMIN to TMAX. µv/ C Input Bias Current +Input or input 7.. µa Input Bias Current Drift na/ C Input Offset Current.. ±µa Open-Loop Gain db INPUT CHARACTERISTICS Input Resistance MΩ Common-Mode Input Capacitance pf Input Common-Mode Voltage Range 4. to +4. V Common-Mode Rejection Ratio VCM = ±4 V 9 db OUTPUT CHARACTERISTICS Output Voltage Swing. to +.. to +.4 V Linear Output Current ma Short-Circuit Current 7 ma Capacitive Load Drive for % Overshoot VO = mv p-p/ V p-p / pf DISABLE CHARACTERISTICS Off Isolation f = MHz 4 db Turn-On Time VO = V to V, % logic to % output 4 ns Turn-Off Time VO = V to V, % logic to % output ns DISABLE Voltage Off/On VDISABLE VLOGIC REFERENCE.7/.9 V Enabled Leakage Current LOGIC REFERENCE =.4 V 7 µa DISABLE = 4. V µa Disabled Leakage Current LOGIC REFERENCE =.4 V µa DISABLE =.4 V µa POWER SUPPLY Operating Range ±. ± ±. V Quiescent Current Output enabled ma Output disabled.. ma +Power Supply Rejection Ratio VCC = +4 V to + V, VEE = V 9 db Power Supply Rejection Ratio VCC = + V, VEE = V to 4 V 9 db
4 AD VS = ± TA = C, RL = kω, gain = +, unless otherwise noted. Table. ADAR/ADARM Parameter Conditions Min Typ Max Unit DYNAMIC PERFORMANCE db Small Signal Bandwidth G = +, CC = pf, VO =. V p-p MHz G = +, CC = 7 pf, VO =. V p-p 7 MHz G = +, CC = pf, VO =. V p-p 7 MHz G = +, CC = pf, VO =. V p-p MHz Slew Rate, V Step G = +, CC = pf V/µs G = +, CC = 7 pf 4 7 V/µs G = +, CC = pf 4 V/µs G = +, CC = pf 4 4 V/µs Settling Time to.% VO = V step, RL = Ω ns Overload Recovery (%) ± V input step, G = + 9 ns DISTORTION/NOISE PERFORMANCE f = MHz HD VO = V p-p 9 dbc HD VO = V p-p dbc f = MHz HD VO = V p-p 7 dbc HD VO = V p-p dbc Input Voltage Noise f = khz.. nv/ Hz Input Current Noise f = khz. pa/ Hz Differential Gain Error NTSC, RL = Ω. % Differential Phase Error NTSC, RL = Ω.4 Degrees DC PERFORMANCE Input Offset Voltage.4. mv Input Offset Voltage Drift TMIN to TMAX. µv/ C Input Bias Current +Input or input. µa Input Bias Current Drift na/ C Input Offset Current.. ±µa Open-Loop Gain 4 db INPUT CHARACTERISTICS Input Resistance MΩ Common-Mode Input Capacitance pf Input Common-Mode Voltage Range. to +. V Common-Mode Rejection Ratio VCM = ± V 9 db OUTPUT CHARACTERISTICS Output Voltage Swing. to +9.. to +. V Linear Output Current 7 ma Short-Circuit Current ma Capacitive Load Drive for % VO = mv p-p/ V p-p / pf Overshoot DISABLE CHARACTERISTICS Off Isolation f = MHz 4 db Turn-On Time VO = V to V, % logic to % output 4 ns Turn-Off Time VO = V to V, % logic to % output ns DISABLE Voltage Off/On VDISABLE VLOGIC REFERENCE./.9 V Enabled Leakage Current LOGIC REFERENCE =.4 V 7 µa DISABLE = 4. V µa Disabled Leakage Current LOGIC REFERENCE =.4 V µa DISABLE =.4 V µa Rev. E Page 4 of
5 AD ADAR/ADARM Parameter Conditions Min Typ Max Unit POWER SUPPLY Operating Range ±. ± ±. V Quiescent Current Output enabled 7.. ma Output disabled.7. ma +Power Supply Rejection Ratio VCC = + V to + V, VEE = V 9 db Power Supply Rejection Ratio VCC = + V, VEE = V to V db VS = TA = C, RL = kω, gain = +, unless otherwise noted. Table. ADAR/ADARM Parameter Conditions Min Typ Max Unit DYNAMIC PERFORMANCE db Small Signal Bandwidth G = +, CC = pf, VO =. V p-p 7 MHz G = +, CC = 7 pf, VO =. V p-p 9 MHz G = +, CC = pf, VO =. V p-p MHz G = +, CC = pf, VO =. V p-p 9 MHz Slew Rate, V Step G = +, CC = pf V/µs G = +, CC = 7 pf 4 V/µs G = +, CC = pf V/µs G = +, CC = pf 9 9 V/µs Settling Time to.% VO = V step, RL = Ω ns Overload Recovery (%) V to. V input step, G = + 4 ns DISTORTION/NOISE PERFORMANCE f = MHz HD VO = V p-p 4 dbc HD VO = V p-p 9 dbc f = MHz HD VO = V p-p dbc HD VO = V p-p dbc Input Voltage Noise f = khz.. nv/ Hz Input Current Noise f = khz. pa/ Hz DC PERFORMANCE Input Offset Voltage.4. mv Input Offset Voltage Drift TMIN to TMAX. µv/ C Input Bias Current +Input or input 7.. µa Input Bias Current Drift na/ C Input Offset Current.. ±µa Open-Loop Gain 7 7 db INPUT CHARACTERISTICS Input Resistance MΩ Common-Mode Input Capacitance pf Input Common-Mode Voltage Range.9 to 4. V Common-Mode Rejection Ratio. V to. V 4 9 db OUTPUT CHARACTERISTICS Output Voltage Swing. to.. to. V Linear Output Current ma Short-Circuit Current ma Capacitive Load Drive for % Overshoot VO = mv p-p/ V p-p / pf Rev. E Page of
6 AD ADAR/ADARM Parameter Conditions Min Typ Max Unit DISABLE CHARACTERISTICS Off Isolation f = MHz 4 db Turn-On Time VO = V to V, % logic to % output 4 ns Turn-Off Time VO = V to V, % logic to % output ns DISABLE Voltage Off/On VDISABLE VLOGIC REFERENCE./.7 V Enabled Leakage Current LOGIC REFERENCE =.4 V 7 µa DISABLE = 4. V µa Disabled Leakage Current LOGIC REFERENCE =.4 V µa DISABLE =.4 V µa POWER SUPPLY Operating Range ±. ± ±. V Quiescent Current Output enabled.7 7. ma Output disabled.. ma +Power Supply Rejection Ratio VCC = 4. V to. V, VEE = V 74 db Power Supply Rejection Ratio VCC = + V, VEE =. V to +. V 7 4 db Rev. E Page of
7 AD ABSOLUTE MAXIMUM RATINGS Table 4. Parameter Supply Voltage Power Dissipation Input Voltage (Common-Mode) Differential Input Voltage Differential Input Current Output Short-Circuit Duration Storage Temperature Operating Temperature Range Lead Temperature Range (Soldering, sec) C Rating.4 V Observed power derating curves ±VS ± V ±. V ± ma Observed power derating curves C to + C 4 C to + C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. The AD inputs are protected by diodes. Current-limiting resistors are not used in order to preserve the low noise. If a differential input exceeds ±. V, the input current should be limited to ± ma. MAXIMUM POWER DISSIPATION The maximum power that can be safely dissipated by the AD is limited by the associated rise in junction temperature. The maximum safe junction temperature for plastic encapsulated devices is determined by the glass transition temperature of the plastic, approximately C. Temporarily exceeding this limit may cause a shift in parametric performance due to a change in the stresses exerted on the die by the package. Exceeding a junction temperature of 7 C for an extended period can result in device failure. While the AD is internally short-circuit protected, this may not be sufficient to guarantee that the maximum junction temperature ( C) is not exceeded under all conditions. To ensure proper operation, it is necessary to observe the maximum power derating curves. MAXIMUM POWER DISSIPATION (mw).. -LEAD SOIC. -LEAD MSOP AMBIENT TEMPERATURE ( C) Figure. Maximum Power Dissipation vs. Temperature Specification is for device in free air: -lead SOIC: θja = C/W; -lead MSOP: θja = 4 C/W -4 ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. E Page 7 of
8 AD PIN CONFIGURATION AND FUNCTION DESCRIPTIONS LOGIC REFERENCE AD DISABLE IN 7 +IN V OUT 4 C COMP - Figure 4. Pin Configuration Table. Function Descriptions Pin No. Mnemonic Description LOGIC REFERENCE Reference for Pin Voltage Level. Connect to logic low supply. IN Inverting Input. +IN Noninverting Input. 4 VS Negative Supply Voltage. CCOMP Compensation Capacitor. Tie to VS. (See the Applications section for value.) VOUT Output. 7 +VS Positive Supply Voltage. DISABLE Disable, Active Low. When Pin (DISABLE) is higher than Pin (LOGIC REFERENCE) by approximately V or more, the part is enabled. When Pin is brought down to within about. V of Pin, the part is disabled. (See the Specifications tables for exact disable and enable voltage levels.) If the disable feature is not going to be used, Pin can be tied to +VS or a logic high source, and Pin can be tied to ground or logic low. Alternatively, if Pin and Pin are not connected, the part will be in an enabled state. Rev. E Page of
9 TYPICAL PERFORMANCE CHARACTERISTICS AD TA = C, VS = ± V, RL = kω, G = +, RF = RG = 499 Ω, RS = 49.9 Ω, RO = 97 Ω, RD =. Ω, CC = 7 pf, CL =, CF =, VOUT = V p-p, frequency = MHz, unless otherwise noted. CLOSED-LOOP 4 G =, R F = kω, R G = Ω, C C = pf G =, R F = kω, R G = 49Ω, C C = pf 9 G =, R F = R G =, C C = 7pF G =, R F = 7Ω, C C = pf.m M M M G M G = V S = ±.V ±V V S = ±.V M M ±V G - Figure. Small Signal Frequency Response vs. Frequency and Gain, VOUT = mv p-p, Noninverting. See Figure 4. Figure. Small Signal Frequency Response vs. Frequency and Supply, VOUT = mv p-p, Noninverting. See Figure 4. 4 G =, R F = kω, R G = Ω, R IN = Ω, C C = pf G = V S = ±.V ±V 9 G =, R F = kω, R G = Ω, R IN =.Ω, C C =.pf G =, R F =, R G = 49Ω, R IN =.4Ω, C C = 4pF 4 V S = ±V G =, R F =, R G =, R IN =.Ω, C C = 7pF.M M M M G - 7 M V S = ±.V M M G -9 Figure. Small Signal Frequency Response vs. Frequency and Gain, VOUT = mv p-p Inverting. See Figure 4. Figure 9. Small Signal Frequency Response vs. Frequency and Supply, VOUT = mv p-p, Inverting. See Figure. 9 G = C C = pf 9 G = 7 7pF 7 V OUT =.V AND mv p-p 4 9pF 4 V OUT = 4V p-p V p-p 7pF 9pF.M M M M G Figure 7. Small Signal Frequency Response vs. Frequency and Compensation Capacitor, VOUT = mv p-p. See Figure M M M Figure. Frequency Response vs. Frequency and VOUT, Noninverting. See Figure 4. G - Rev. E Page 9 of
10 AD 9 G = 9 G = R F = R G R F = R F = kω 7 4 kω 7 4 R F = Ω R F = Ω R L = Ω R F = 7Ω.M M M M G - R F = kω AND C F =.pf.m M M M G -4 Figure. Large Signal Frequency Response vs. Frequency and Load, Noninverting. See Figure 49. Figure 4. Small Signal Frequency Response vs. Frequency and RF, Noninverting, VOUT = mv p-p. See Figure G = + C + C 9 G = 4 + C V OUT = V p-p 4 C V OUT = mv p-p R S = 49.9Ω R S = Ω M + C 4 C M M G - 9 R S = 49Ω.M M M M G - Figure. Frequency Response vs. Frequency, Temperature, and VOUT, Noninverting. See Figure 4. Figure. Small Signal Frequency Response vs. Frequency and RS, Noninverting, VOUT = mv p-p. See Figure 4. G = pf pf 9 9 pf pf pf OPEN-LOOP PHASE (Degrees) 4 9 M M M G - k k M M M 9 G - Figure. Small Signal Frequency Response vs. Frequency and Capacitive Load, Noninverting, VOUT = mv p-p. See Figure 49 and Figure 7. Figure. Open-Loop Gain and Phase vs. Frequency, RG = Ω, RF = kω, RO = 97 Ω, RD =. Ω, CC = pf. See Figure. Rev. E Page of
11 AD.4 G =. V S = ±.V 4.. ±V ±V P OUT (dbm) 7 f =.MHz f f 97Ω P OUT.Ω Ω 9..4 M M -7 M FREQUENCY (MHz) -. Figure 7.. db Flatness vs. Frequency and Supply, VOUT = V p-p, RL = Ω, Noninverting. See Figure 49. Figure. Intermodulation Distortion vs. Frequency DISTORTION (dbc) R L = Ω R L = kω SECOND THIRD-ORDER INTERCEPT (dbm) 4 4 V S = ±.V V S = ±V.M THIRD M M - M FREQUENCY (MHz) - Figure. Second and Third Harmonic Distortion vs. Frequency and RL Figure. Third-Order Intercept vs. Frequency and Supply Voltage 4 DISTORTION (dbc) 7 THIRD SECOND V S = ±.V 9 SECOND V S = ±V THIRD SECOND k M V S = ±V M -9 M DISTORTION (dbc) 7 9 SECOND R L = Ω THIRD SECOND R L = kω THIRD 4 V OUT (V p-p) - Figure 9. Second and Third Harmonic Distortion vs. Frequency and VS Figure. Second and Third Harmonic Distortion vs. VOUT and RL Rev. E Page of
12 AD.. DISTORTION (dbc) 7 9 THIRD SECOND f C = MHz SECOND f C = MHz THIRD 4 V OUT (V p-p) - POSITIVE OUTPUT VOLTAGE (V) POSITIVE OUTPUT NEGATIVE OUTPUT LOAD (Ω) NEGATIVE OUTPUT VOLTAGE (V) - Figure. Second and Third Harmonic Distortion vs. VOUT and Fundamental Frequency (fc), G = + Figure. DC Output Voltage vs. Load. See Figure 4. 4 DISTORTION (dbc) 7 9 SECOND THIRD SECOND THIRD f C = MHz f C = MHz 4 V OUT (V p-p) -4 SHORT-CIRCUIT CURRENT (ma) 4 V S = ± V S = ±. V S = ±. 7 9 TEMPERATURE ( C) -7 Figure 4. Second and Third Harmonic Distortion vs. VOUT and Fundamental Frequency (fc), G = + Figure 7. Short-Circuit Current to Ground vs. Temperature DISTORTION (dbc) 7 9 f C = MHz R L = kω R F = R G G = + SECOND THIRD V OUT (mv) 4 G = R L = kω, Ω 4 FEEDBACK RESISTANCE (Ω) TIME (ns) - Figure. Second and Third Harmonic Distortion vs. Feedback Resistor (RF) Figure. Small Signal Transient Response vs. RL, VO = mv p-p. See Figure 49, Noninverting. Rev. E Page of
13 AD. V O = 4V p-p G =. V O = V p-p G =. R L = kω. V OUT (V) R L = Ω V OUT (V) V S = ±.V.. V S = ±V. 4 TIME (ns) TIME (ns) - Figure 9. Large Signal Transient Response vs. RL. See Figure 49, Noninverting. Figure. Large Signal Transient Response vs. VS. See Figure 4. 4 V O = 4V p-p G = V IN = ±V G = + V IN = V/DIV V OUT = V/DIV V OUT, R L = kω V IN R L = Ω VOLTS V OUT 4 TIME (ns) - V IN 4 TIME (ns) - Figure. Large Signal Transient Response. See Figure, Inverting. Figure. Overdrive Recovery vs. RL. See Figure 49.. C L = pf G = V O = 4V p-p G = V OUT (V).. C L = pf, pf OUTPUT SETTLING +.%.% ns. - VERT =.mv/div HOR = ns/div -4 4 TIME (ns) Figure. Large Signal Transient Response vs. CL. See Figure 4. Figure 4..% Settling Time, V Step Rev. E Page of
14 AD SETTLING (µv) 4 4 V PULSEWIDTH = ns PULSEWIDTH = µs INPUT CURRENT NOISE (pa/ Hz) V t 4 4 TIME (µs) Figure. Long-Term Settling, V to V, VS = ± V, G = + - k k k M M Figure. Input Current Noise vs. Frequency - 4 G = V OUT (mv) VOLTAGE OFFSET (mv) TIME (ns) TEMPERATURE ( C) -9 Figure. Small Signal Transient Response, VO = mv p-p, G = +. See Figure 4. Figure 9. VOS vs. Temperature.4. VOLTAGE NOISE (nv/ Hz).nV/ Hz INPUT BIAS CURRENT (µa) k k k M -7 M. 7 TEMPERATURE ( C) -4 Figure 7. Input Voltage Noise vs. Frequency Figure 4. Input Bias Current vs. Temperature Rev. E Page 4 of
15 AD 4 CMRR (db) 7 9 DISABLED ISOLATION (db) 4 7 k k M M M -4 9.M M M M G -44 Figure 4. CMRR vs. Frequency. See Figure. Figure 44. Input to Output Isolation, Chip Disabled. See Figure 4. k k k OUTPUT IMPEDANCE (Ω).. OUTPUT IMPEDANCE (Ω) k k k... k k M M M G -4 k k M M M G -4 Figure 4. Output Impedance vs. Frequency, Chip Enabled. See Figure. Figure 4. Output Impedance vs. Frequency, Chip Disabled. See Figure. 4V DISABLE V PSRR V V t EN = 4ns V OUTPUT t DIS = ns PSRR (db) 4 7 V S = ±.V +PSRR V S = ±V V S = ±V 4 TIME (ns) Figure 4. Enable (ten)/disable (tdis) Time vs. VOUT. See Figure k k M M M Figure 4. PSRR vs. Frequency and Supply Voltage. See Figure and Figure M Rev. E Page of
16 AD.. SUPPLY CURRENT (ma) TEMPERATURE ( C) Figure 47. Quiescent Supply Current vs. Temperature -47 Rev. E Page of
17 AD TEST CIRCUITS Ω Ω CABLE R IN 49.9Ω R S C C R O R D Ω CABLE Ω AD C C Ω HP7D NETWORK ANALYZER R R G F C F Figure 4. Noninverting Gain -4 R G 7pF R F Figure. Output Impedance, Chip Enabled - Ω CABLE R S FET PROBE 49.9Ω AD Ω R IN 49.9Ω C C C L R L.V 4V 49.9Ω 49.9Ω LOGIC REF DISABLE C C 97Ω.Ω R G R F 7pF C F Figure 49. Noninverting Gain and FET Probe Figure. Enable/Disable 49.9Ω R O Ω CABLE HP7D NETWORK ANALYZER Ω Ω CABLE RIN 49.9Ω R G C C R F Figure. Inverting Gain R D - Ω 49.9Ω 49.9Ω Ω LOGIC REF DISABLE AD Ω CABLE FET PROBE kω HP7D NETWORK ANALYZER C C 7pF Figure 4. Input to Output Isolation, Chip Disabled -4 Ω Ω AD C C 49.9Ω Ω AD Ω HP7D NETWORK ANALYZER.Ω 7pF - C C 7pF - Figure. CMRR Figure. Output Impedance, Chip Disabled Rev. E Page 7 of
18 AD BIAS BNC Ω HP7D NETWORK ANALYZER Ω BIAS BNC Ω HP7D NETWORK ANALYZER Ω Ω CABLE Ω CABLE 49Ω C C 7pF 49.9Ω, W 97Ω.Ω 49Ω 49.9Ω W C C 7pF 97Ω.Ω - -7 Figure. Positive PSRR Figure 7. Negative PSRR Rev. E Page of
19 AD APPLICATIONS The typical voltage feedback op amp is frequency stabilized with a fixed internal capacitor, CINTERNAL, using dominant pole compensation. To a first-order approximation, voltage feedback op amps have a fixed gain bandwidth product. For example, if its db bandwidth is MHz for a gain of G = +; at a gain of G = +, its bandwidth will be only about MHz. The AD is a voltage feedback op amp with a minimal CINTERNAL of about. pf. By adding an external compensation capacitor, CC, the user can circumvent the fixed gain bandwidth limitation of other voltage feedback op amps. Unlike the typical op amp with fixed compensation, the AD allows the user to Maximize the amplifier bandwidth for closed-loop gains between and, avoiding the usual loss of bandwidth and slew rate. Optimize the trade-off between bandwidth and phase margin for a particular application. Match bandwidth in gain blocks with different noise gains, such as when designing differential amplifiers (as shown in Figure ). OPEN-LOOP C C = pf C C = pf (B) (A) k k k M M M G G (B) (A) (C) Figure. Simplified Diagram of Open-Loop Gain and Phase Response Figure is the AD gain and phase plot that has been simplified for instructional purposes. Arrow A in Figure shows a bandwidth of about MHz and a phase margin at about when the desired closed-loop gain is G = + and the value chosen for the external compensation capacitor is CC = pf. If the gain is changed to G = + and CC is fixed at pf, then (as expected for a typical op amp) the bandwidth is degraded to about MHz and the phase margin increases to 9 (Arrow B). However, (C) 9 4 PHASE (Degrees) - by reducing CC to zero, the bandwidth and phase margin return to about MHz and (Arrow C), respectively. In addition, the slew rate is dramatically increased, as it roughly varies with the inverse of CC. COMPENSATION CAPACITANCE (pf) NOISE GAIN (V/V) Figure 9. Suggested Compensation Capacitance vs. Gain for Maintaining db Peaking Table and Figure 9 provide recommended values of compensation capacitance at various gains and the corresponding slew rate, bandwidth, and noise. Note that the value of the compensation capacitor depends on the circuit noise gain, not the voltage gain. As shown in Figure, the noise gain, GN, of an op amp gain block is equal to its noninverting voltage gain, regardless of whether it is actually used for inverting or noninverting gain. Thus, Noninverting GN = RF/RG + Inverting GN = RF/RG + R S + AD C COMP G = G N = NONINVERTING R F Ω R G Ω R G Ω R F Ω AD + C COMP INVERTING Figure. The Noise Gain of Both is G = 4 G N = -9 - Rev. E Page 9 of
20 AD Table. Recommended Component Values See Figure 49. CF = CL =, RL = kω, RIN = 49.9 Ω. Noise Gain (Noninverting Gain) RS (Ω) RF (Ω) RG (Ω) CCOMP (pf) db SS BW (MHz) Output Noise (AD Only) (nv/ Hz) Slew Rate (V/µs) 7 7 NA k k k k With the AD, a variety of trade-offs can be made to finetune its dynamic performance. Sometimes more bandwidth or slew rate is needed at a particular gain. Reducing the compensation capacitance, as illustrated in Figure 7, will increase the bandwidth and peaking due to a decrease in phase margin. On the other hand, if more stability is needed, increasing the compensation cap will decrease the bandwidth while increasing the phase margin. As with all high speed amplifiers, parasitic capacitance and inductance around the amplifier can affect its dynamic response. Often, the input capacitance (due to the op amp itself, as well as the PC board) has a significant effect. The feedback resistance, together with the input capacitance, can contribute to a loss of phase margin, thereby affecting the high frequency response, as shown in Figure 4. A capacitor (CF) in parallel with the feedback resistor can compensate for this phase loss. Output Noise (AD with Resistors) (nv/ Hz) Additionally, any resistance in series with the source will create a pole with the input capacitance (as well as dampen high frequency resonance due to package and board inductance and capacitance), the effect of which is shown in Figure. It must also be noted that increasing resistor values will increase the overall noise of the amplifier, and that reducing the feedback resistor value will increase the load on the output stage, thus increasing distortion (Figure ). USING THE DISABLE FEATURE When Pin (DISABLE) is higher than Pin (LOGIC REFERENCE) by approximately V or more, the part is enabled. When Pin is brought down to within about. V of Pin, the part is disabled. See Table for exact disable and enable voltage levels. If the disable feature is not going to be used, Pin can be tied to VS or a logic high source, and Pin can be tied to ground or logic low. Alternatively, if Pin and Pin are not connected, the part will be in an enabled state. Rev. E Page of
21 AD THEORY OF OPERATION The AD is fabricated on the second generation of Analog Devices proprietary High Voltage extra-fast Complementary Bipolar (XFCB) process, which enables the construction of PNP and NPN transistors with similar fts in the GHz region. The transistors are dielectrically isolated from the substrate (and each other), eliminating the parasitic and latch-up problems caused by junction isolation. It also reduces nonlinear capacitance (a source of distortion) and allows a higher transistor, ft, for a given quiescent current. The supply current is trimmed, which results in less part-to-part variation of bandwidth, slew rate, distortion, and settling time. As shown in Figure, the AD input stage consists of an NPN differential pair in which each transistor operates at a. ma collector current. This allows the input devices a high transconductance; thus, the AD has a low input noise of. nv/ khz. The input stage drives a folded cascode that consists of a pair of PNP transistors. The folded cascode and current mirror provide a differential to single-ended conversion of signal current. This current then drives the high impedance node (Pin ), where the CC external capacitor is connected. The output stage preserves this high impedance with a current gain of,, so that the AD can maintain a high open-loop gain even when driving heavy loads. Two internal diode clamps across the inputs (Pin and Pin ) protect the input transistors from large voltages that could otherwise cause emitter-base breakdown, which would result in degradation of offset voltage and input bias current. PCB LAYOUT CONSIDERATIONS As with all high speed op amps, achieving optimum performance from the AD requires careful attention to PC board layout. Particular care must be exercised to minimize lead lengths between the ground leads of the bypass capacitors and between the compensation capacitor and the negative supply. Otherwise, lead inductance can influence the frequency response and even cause high frequency oscillations. Use of a multilayer printed circuit board, with an internal ground plane, will reduce ground noise and enable a compact component arrangement. Due to the relatively high impedance of Pin and low values of the compensation capacitor, a guard ring is recommended. The guard ring is simply a PC trace that encircles Pin and is connected to the output, Pin, which is at the same potential as Pin. This serves two functions. It shields Pin from any local circuit noise generated by surrounding circuitry. It also minimizes stray capacitance, which would tend to otherwise reduce the bandwidth. An example of a guard ring layout may be seen in Figure. Also shown in Figure, the compensation capacitor is located immediately adjacent to the edge of the AD package, spanning Pin 4 and Pin. This capacitor must be a high quality surfacemount COG or NPO ceramic. The use of leaded capacitors is not recommended. The high frequency bypass capacitor(s) should be located immediately adjacent to the supplies, Pin 4 and Pin 7. +IN OUTPUT To achieve the shortest possible lead length at the inverting input, the feedback resistor RF is located beneath the board and just spans the distance from the output, Pin, to inverting input Pin. The return node of resistor RG should be situated as close as possible to the return node of the negative supply bypass capacitor connected to Pin 4. (TOP VIEW) IN C INTERNAL.pF LOGIC REFERENCE IN 7 DISABLE BYPASS CAPACITOR C COMP Figure. Simplified Schematic CC - +IN 4 C COMP V OUT GROUND PLANE METAL BYPASS CAPACITOR GROUND PLANE COMPENSATION CAPACITOR - Figure. Recommended Location of Critical Components and Guard Ring Rev. E Page of
22 AD DRIVING -BIT ADCS Low noise and adjustable compensation make the AD especially suitable as a buffer/driver for high resolution analogto-digital converters. As seen in Figure 9, the harmonic distortion is better than 9 dbc at frequencies between khz and MHz. This is a real advantage for complex waveforms that contain high frequency information, as the phase and gain integrity of the sampled waveform can be preserved throughout the conversion process. The increase in loop gain results in improved output regulation and lower noise when the converter input changes state during a sample. This advantage is particularly apparent when using -bit high resolution ADCs with high sampling rates. Figure shows a typical ADC driver configuration. The AD is in an inverting gain of 7., fc is khz, and its output voltage is V p-p. The results are listed in Table 7. Ω 9Ω R G Ω +V + AD C C pf V pf R F.kΩ IN HI IN HI +V AD7 7kSPS Figure. Inverting ADC Driver, Gain = 7., fc = khz Table 7. Summary of ADC Driver Performance fc = khz, VOUT = V p-p. Parameter Measurement Unit Second Harmonic Distortion. dbc Third Harmonic Distortion 9. dbc THD. dbc SFDR. dbc Ω +V Ω + Ω AD C C R G.Ω V R F 7Ω OPTIONAL C F IN HI IN LO BITS +V - AD7 7kSPS ADC Figure 4. Noninverting ADC Driver, Gain =, fc = khz BITS -4 Table. Summary of ADC Driver Performance fc = khz, VOUT = V p-p. Parameter Measurement Unit Second Harmonic Distortion 9. dbc Third Harmonic Distortion.4 dbc THD 4.4 dbc SFDR.4 dbc Figure 4 shows another ADC driver connection. The circuit was tested with a noninverting gain of. and an output voltage of approximately V p-p for optimum resolution and noise performance. No filtering was used. An FFT was performed using Analog Devices evaluation software for the AD7 -bit converter. The results are listed in Table. DIFFERENTIAL DRIVER The AD is uniquely suited as a low noise differential driver for many ADCs, balanced lines, and other applications requiring differential drive. If pairs of internally compensated op amps are configured as inverter and follower, the noise gain of the inverter will be higher than that of the follower section, resulting in an imbalance in the frequency response (see Figure ). A better solution takes advantage of the external compensation feature of the AD. By reducing the CCOMP value of the inverter, its bandwidth may be increased to match that of the follower, avoiding compromises in gain bandwidth and phase delay. The inverting and noninverting bandwidths can be closely matched using the compensation feature, thus minimizing distortion. Figure illustrates an inverter-follower driver circuit operating at a gain of, using individually compensated ADs. The values of feedback and load resistors were selected to provide a total load of less than kω, and the equivalent resistances seen at each op amp s inputs were matched to minimize offset voltage and drift. Figure 7 is a plot of the resulting ac responses of driver halves. V IN 49.9Ω 49Ω G = + + AD 7pF Ω G = + Ω AD pf 4Ω kω kω V OUT V OUT - Figure. Differential Amplifier Rev. E Page of
23 AD C 9 V IN R R C AD V OUT 9 G = G = + k M M M G Figure. AC Response of Two Identically Compensated High Speed Op Amps Configured for a Gain of + and a Gain of 9 - R G Figure. Schematic of a Second-Order Low-Pass Active Filter Table 9. Typical Component Values for Second-Order Low- Pass Filter of Figure Gain R (Ω) R (Ω) RF (Ω) RS (Ω) C C CC nf nf 7 pf nf nf pf 4 C C R F - G = ± G = G = 9 k M M M G Figure 7. AC Response of Two Dissimilarly Compensated AD Op Amps (Figure ) Configured for a Gain of + and a Gain of. Note the Close Gain Match. USING THE AD IN ACTIVE FILTERS The low noise and high gain bandwidth of the AD make it an excellent choice in active filter circuits. Most active filter literature provides resistor and capacitor values for various filters but neglects the effect of the op amp s finite bandwidth on filter performance; ideal filter response with infinite loop gain is implied. Unfortunately, real filters do not behave in this manner. Instead, they exhibit finite limits of attenuation, depending on the gain bandwidth of the active device. Good low-pass filter performance requires an op amp with high gain bandwidth for attenuation at high frequencies, and low noise and high dc gain for low frequency, pass-band performance. Figure shows the schematic of a -pole, low-pass active filter, and lists typical component values for filters having a Besseltype response with a gain of and a gain of. Figure 9 is a network analyzer plot of this filter s performance k k k M M Figure 9. Frequency Response of the Filter Circuit of Figure for Two Different Gains DRIVING CAPACITIVE LOADS When the AD drives a capacitive load, the high frequency response may show excessive peaking before it rolls off. Two techniques can be used to improve stability at high frequency and reduce peaking. The first technique is to increase the compensation capacitor, CC, which reduces the peaking while maintaining gain flatness at low frequencies. The second technique is to add a resistor, RSNUB, in series between the output pin of the AD and the capacitive load, CL. Figure 7 shows the response of the AD when both CC and RSNUB are used to reduce peaking. For a given CL, Figure 7 can be used to determine the value of RSNUB that maintains db of peaking in the frequency response. Note, however, that using RSNUB attenuates the low frequency output by a factor of RLOAD/(RSNUB + RLOAD). -9 Rev. E Page of
24 AD Ω 49.9Ω FET PROBE R SNUB pf C C R L kω C C = 7pF; R SNUB = Ω C C = pf; R SNUB = Ω R SNUB (Ω) 4 4 C C = pf; R SNUB = 7.4Ω.. FREQUENCY (MHz) CAPACITIVE LOAD (pf) -7 Figure 7. Peaking vs. RSNUB and CC for CL = pf Figure 7. Relationship of RSNUB vs. CL for db Peaking at a Gain of + Rev. E Page 4 of
25 AD OUTLINE DIMENSIONS. (.9) 4. (.9) 4. (.74). (.497) 4. (.44). (.4). (.9). (.4) COPLANARITY..7 (.) BSC SEATING PLANE.7 (.). (.). (.). (.). (.9).7 (.7). (.9). (.99) 4.7 (.).4 (.7) COMPLIANT TO JEDEC STANDARDS MS-AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN Figure 7. -Lead Standard Small Outline Package [SOIC] Narrow Body (R-) Dimension shown in millimeters and (inches). BSC. BSC BSC PIN. BSC.... COPLANARITY.. MAX SEATING PLANE.. COMPLIANT TO JEDEC STANDARDS MO-7AA...4 Figure 7. -Lead Mini Small Outline Package [MSOP] (RM-) Dimensions shown in millimeters ORDERING GUIDE Model Temperature Range Package Description Package Option Branding ADAR 4 C to + C -Lead SOIC R- ADAR-REEL 4 C to + C -Lead SOIC R- ADAR-REEL7 4 C to + C -Lead SOIC R- ADARZ 4 C to + C -Lead SOIC R- ADARZ-REEL 4 C to + C -Lead SOIC R- ADARZ-REEL7 4 C to + C -Lead SOIC R- ADARM 4 C to + C -Lead MSOP RM- HNA ADARM-REEL 4 C to + C -Lead MSOP RM- HNA ADARM-REEL7 4 C to + C -Lead MSOP RM- HNA ADARMZ 4 C to + C -Lead MSOP RM- HNA ADARMZ-REEL 4 C to + C -Lead MSOP RM- HNA ADARMZ-REEL7 4 C to + C -Lead MSOP RM- HNA Z = Pb-free part. Rev. E Page of
26 AD NOTES Rev. E Page of
27 AD NOTES Rev. E Page 7 of
28 AD NOTES Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C--/(E) Rev. E Page of
Low Noise, High Speed Amplifier for 16-Bit Systems AD8021
Low Noise, High Speed Amplifier for -Bit Systems AD FEATURES Low Noise. nv/ Hz Input Voltage Noise. pa/ Hz Input Current Noise Custom Compensation Constant Bandwidth from G = to G = High Speed MHz (G =
More informationLow Noise, High Speed Amplifier for 16-Bit Systems AD8021
Low Noise, High Speed Amplifier for -Bit Systems AD FEATURES Low noise. nv/ Hz input voltage noise. pa/ Hz input current noise Custom compensation Constant bandwidth from G = to G = High speed MHz (G =
More informationRail-to-Rail, High Output Current Amplifier AD8397
Rail-to-Rail, High Output Current Amplifier FEATURES Dual operational amplifier Voltage feedback Wide supply range from 3 V to 24 V Rail-to-rail output Output swing to within.5 V of supply rails High linear
More informationVery Low Distortion, Precision Difference Amplifier AD8274
Very Low Distortion, Precision Difference Amplifier AD8274 FEATURES Very low distortion.2% THD + N (2 khz).% THD + N ( khz) Drives Ω loads Excellent gain accuracy.3% maximum gain error 2 ppm/ C maximum
More informationREV. D Ultralow Distortion High Speed Amplifiers AD8007/AD8008 FEATURES CONNECTION DIAGRAMS Extremely Low Distortion Second Harmonic 88 5 MHz SO
Ultralow Distortion High Speed Amplifiers FEATURES CONNECTION DIAGRAMS Extremely Low Distortion Second Harmonic 88 dbc @ 5 MHz SOIC (R) SC7 (KS-5) 8 dbc @ MHz (AD87) AD87 AD87 NC V (Top View) 8 NC OUT
More informationDual, Current Feedback Low Power Op Amp AD812
a FEATURES Two Video Amplifiers in One -Lead SOIC Package Optimized for Driving Cables in Video Systems Excellent Video Specifications (R L = ): Gain Flatness. db to MHz.% Differential Gain Error. Differential
More information270 MHz, 400 μa Current Feedback Amplifier AD8005
Data Sheet 27 MHz, μa Current Feedback Amplifier AD85 FEATURES Ultralow power μa power supply current ( mw on ±5 VS) Specified for single supply operation High speed 27 MHz, 3 db bandwidth (G = +) 7 MHz,
More informationUltralow Distortion, High Speed Amplifiers AD8007/AD8008
Ultralow Distortion, High Speed Amplifiers AD87/AD88 FEATURES Extremely low distortion Second harmonic 88 dbc @ 5 MHz 8 dbc @ MHz (AD87) 77 dbc @ MHz (AD88) Third harmonic dbc @ 5 MHz 9 dbc @ MHz (AD87)
More informationImproved Second Source to the EL2020 ADEL2020
Improved Second Source to the EL ADEL FEATURES Ideal for Video Applications.% Differential Gain. Differential Phase. db Bandwidth to 5 MHz (G = +) High Speed 9 MHz Bandwidth ( db) 5 V/ s Slew Rate ns Settling
More information250 MHz, General Purpose Voltage Feedback Op Amps AD8047/AD8048
5 MHz, General Purpose Voltage Feedback Op Amps AD8/AD88 FEATURES Wide Bandwidth AD8, G = + AD88, G = + Small Signal 5 MHz 6 MHz Large Signal ( V p-p) MHz 6 MHz 5.8 ma Typical Supply Current Low Distortion,
More informationLow Cost, High Speed Differential Amplifier AD8132
Low Cost, High Speed Differential Amplifier FEATURES High speed 350 MHz, 3 db bandwidth 1200 V/μs slew rate Resistor set gain Internal common-mode feedback Improved gain and phase balance 68 db @ 10 MHz
More informationLow Power, 350 MHz Voltage Feedback Amplifiers AD8038/AD8039
Low Power, MHz Voltage Feedback Amplifiers AD88/AD89 FEATURES Low power: ma supply current/amp High speed MHz, db bandwidth (G = +) V/μs slew rate Low cost Low noise 8 nv/ Hz @ khz fa/ Hz @ khz Low input
More information200 ma Output Current High-Speed Amplifier AD8010
a FEATURES 2 ma of Output Current 9 Load SFDR 54 dbc @ MHz Differential Gain Error.4%, f = 4.43 MHz Differential Phase Error.6, f = 4.43 MHz Maintains Video Specifications Driving Eight Parallel 75 Loads.2%
More informationVery Low Distortion, Dual-Channel, High Precision Difference Amplifier AD8274 FUNCTIONAL BLOCK DIAGRAM +V S FEATURES APPLICATIONS GENERAL DESCRIPTION
Very Low Distortion, Dual-Channel, High Precision Difference Amplifier AD8273 FEATURES ±4 V HBM ESD Very low distortion.25% THD + N (2 khz).15% THD + N (1 khz) Drives 6 Ω loads Two gain settings Gain of
More informationLow Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifier AD8276
Low Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifier AD87 FEATURES Wide input range Rugged input overvoltage protection Low supply current: μa maximum Low power dissipation:. mw at VS
More informationLow Cost, General Purpose High Speed JFET Amplifier AD825
a FEATURES High Speed 41 MHz, 3 db Bandwidth 125 V/ s Slew Rate 8 ns Settling Time Input Bias Current of 2 pa and Noise Current of 1 fa/ Hz Input Voltage Noise of 12 nv/ Hz Fully Specified Power Supplies:
More informationHigh Performance, 145 MHz FastFET Op Amps AD8065/AD8066
High Performance, 45 MHz FastFET Op Amps AD8065/AD8066 FEATURE FET input amplifier pa input bias current Low cost High speed: 45 MHz, 3 db bandwidth (G = +) 80 V/μs slew rate (G = +2) Low noise 7 nv/ Hz
More informationAD864/AD8642/AD8643 TABLE OF CONTENTS Specifications... 3 Electrical Characteristics... 3 Absolute Maximum Ratings... 5 ESD Caution... 5 Typical Perfo
FEATURES Low supply current: 25 µa max Very low input bias current: pa max Low offset voltage: 75 µv max Single-supply operation: 5 V to 26 V Dual-supply operation: ±2.5 V to ±3 V Rail-to-rail output Unity-gain
More informationHigh Speed, G = +2, Low Cost, Triple Op Amp ADA4862-3
High Speed,, Low Cost, Triple Op Amp ADA4862-3 FEATURES Ideal for RGB/HD/SD video Supports 8i/72p resolution High speed 3 db bandwidth: 3 MHz Slew rate: 75 V/μs Settling time: 9 ns (.5%). db flatness:
More information1.5 GHz Ultrahigh Speed Op Amp AD8000
.5 GHz Ultrahigh Speed Op Amp AD8 FEATURES High speed.5 GHz, db bandwidth (G = +) 65 MHz, full power bandwidth (, VO = 2 V p-p) Slew rate: 4 V/µs.% settling time: 2 ns Excellent video specifications. db
More informationHigh-Speed, Low-Power Dual Operational Amplifier AD826
a FEATURES High Speed: MHz Unity Gain Bandwidth 3 V/ s Slew Rate 7 ns Settling Time to.% Low Power: 7. ma Max Power Supply Current Per Amp Easy to Use: Drives Unlimited Capacitive Loads ma Min Output Current
More informationADA485-/ADA485- TABLE OF CONTENTS Features... Applications... Pin Configurations... General Description... Revision History... Specifications... 3 Spe
NC NC NC NC 5 6 7 8 6 NC 4 PD 3 PD FEATURES Ultralow power-down current: 5 na/amplifier maximum Low quiescent current:.4 ma/amplifier High speed 75 MHz, 3 db bandwidth V/μs slew rate 85 ns settling time
More informationAD MHz, 20 V/μs, G = 1, 10, 100, 1000 i CMOS Programmable Gain Instrumentation Amplifier. Preliminary Technical Data FEATURES
Preliminary Technical Data 0 MHz, 20 V/μs, G =, 0, 00, 000 i CMOS Programmable Gain Instrumentation Amplifier FEATURES Small package: 0-lead MSOP Programmable gains:, 0, 00, 000 Digital or pin-programmable
More information1.5 GHz Ultrahigh Speed Op Amp AD8000
.5 GHz Ultrahigh Speed Op Amp AD8 FEATURES High speed.5 GHz, db bandwidth (G = +) 65 MHz, full power bandwidth (, VO = 2 V p-p) Slew rate: 4 V/µs.% settling time: 2 ns Excellent video specifications. db
More informationHigh Voltage, Low Noise, Low Distortion, Unity-Gain Stable, High Speed Op Amp ADA4898-1/ADA4898-2
FEATURES Ultralow noise.9 nv/ Hz.4 pa/ Hz. nv/ Hz at Hz Ultralow distortion: 93 dbc at 5 khz Wide supply voltage range: ±5 V to ±6 V High speed 3 db bandwidth: 65 MHz (G = +) Slew rate: 55 V/µs Unity gain
More informationQuad 150 MHz Rail-to-Rail Amplifier AD8044
a FEATURES Single AD84 and Dual AD842 Also Available Fully Specified at + V, +5 V, and 5 V Supplies Output Swings to Within 25 mv of Either Rail Input Voltage Range Extends 2 mv Below Ground No Phase Reversal
More informationUltralow Distortion, Wide Bandwidth Voltage Feedback Op Amps AD9631/AD9632
a Ultralow Distortion, Wide Bandwidth Voltage Feedback Op Amps / FEATURES Wide Bandwidth, G = +, G = +2 Small Signal 32 MHz 25 MHz Large Signal (4 V p-p) 75 MHz 8 MHz Ultralow Distortion (SFDR), Low Noise
More informationDual Precision, Low Cost, High Speed BiFET Op Amp AD712-EP
Dual Precision, Low Cost, High Speed BiFET Op Amp FEATURES Supports defense and aerospace applications (AQEC standard) Military temperature range ( 55 C to +125 C) Controlled manufacturing baseline One
More informationSingle Supply, Low Power, Triple Video Amplifier AD8013
a FEATURES Three Video Amplifiers in One Package Drives Large Capacitive Load Excellent Video Specifications (R L = 5 ) Gain Flatness. db to MHz.% Differential Gain Error. Differential Phase Error Low
More informationLow Cost, High Speed, Rail-to-Rail, Output Op Amps ADA4851-1/ADA4851-2/ADA4851-4
Low Cost, High Speed, Rail-to-Rail, Output Op Amps ADA485-/ADA485-/ADA485-4 FEATURES High speed 3 MHz, 3 db bandwidth 375 V/μs slew rate 55 ns settling time to.% Excellent video specifications. db flatness:
More informationSingle Supply, Low Power Triple Video Amplifier AD813
a FEATURES Low Cost Three Video Amplifiers in One Package Optimized for Driving Cables in Video Systems Excellent Video Specifications (R L = 15 ) Gain Flatness.1 db to 5 MHz.3% Differential Gain Error.6
More informationLow Power, Precision, Auto-Zero Op Amps AD8538/AD8539 FEATURES Low offset voltage: 13 μv maximum Input offset drift: 0.03 μv/ C Single-supply operatio
Low Power, Precision, Auto-Zero Op Amps FEATURES Low offset voltage: 3 μv maximum Input offset drift:.3 μv/ C Single-supply operation: 2.7 V to 5.5 V High gain, CMRR, and PSRR Low input bias current: 25
More informationSingle-Supply, Rail-to-Rail, Low Power FET-Input Op Amp AD820
Single-Supply, Rail-to-Rail, Low Power FET-Input Op Amp AD82 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5 V
More informationDual, Low Power Video Op Amp AD828
a FEATURES Excellent Video Performance Differential Gain and Phase Error of.% and. High Speed MHz db Bandwidth (G = +) V/ s Slew Rate ns Settling Time to.% Low Power ma Max Power Supply Current High Output
More informationSingle Supply, Rail to Rail Low Power FET-Input Op Amp AD820
a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from V to V Dual Supply Capability from. V to 8 V Excellent Load Drive
More informationLow Cost, High Speed Rail-to-Rail Amplifiers AD8091/AD8092
Low Cost, High Speed Rail-to-Rail Amplifiers AD891/AD892 FEATURES Low cost single (AD891) and dual (AD892) amplifiers Fully specified at +3 V, +5 V, and ±5 V supplies Single-supply operation Output swings
More informationSingle Supply, Rail to Rail Low Power FET-Input Op Amp AD820
a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from + V to + V Dual Supply Capability from. V to 8 V Excellent Load
More informationLow Cost, Precision JFET Input Operational Amplifiers ADA4000-1/ADA4000-2/ADA4000-4
Low Cost, Precision JFET Input Operational Amplifiers ADA-/ADA-/ADA- FEATURES High slew rate: V/μs Fast settling time Low offset voltage:.7 mv maximum Bias current: pa maximum ± V to ±8 V operation Low
More informationSingle-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820
Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD82 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5 V
More informationSingle-Supply, High Speed, Triple Op Amp with Charge Pump ADA4858-3
Single-Supply, High Speed, Triple Op Amp with Charge Pump FEATURES Integrated charge pump Supply range: 3 V to 5.5 V Output range: 3.3 V to.8 V 5 ma maximum output current for external use at 3 V High
More informationLow Power, Rail-to-Rail Output, Precision JFET Amplifiers AD8641/AD8642/AD8643
Data Sheet Low Power, Rail-to-Rail Output, Precision JFET Amplifiers AD864/AD8642/AD8643 FEATURES Low supply current: 25 μa max Very low input bias current: pa max Low offset voltage: 75 μv max Single-supply
More information15 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP
5 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP FEATURES Supports defense and aerospace applications (AQEC standard) Military temperature range ( 55 C to +25 C) Controlled manufacturing baseline
More informationPrecision, 16 MHz CBFET Op Amp AD845
a FEATURES Replaces Hybrid Amplifiers in Many Applications AC PERFORMANCE: Settles to 0.01% in 350 ns 100 V/ s Slew Rate 12.8 MHz Min Unity Gain Bandwidth 1.75 MHz Full Power Bandwidth at 20 V p-p DC PERFORMANCE:
More informationHigh Output Current Differential Driver AD815
a FEATURES Flexible Configuration Differential Input and Output Driver or Two Single-Ended Drivers Industrial Temperature Range High Output Power Thermally Enhanced SOIC 4 ma Minimum Output Drive/Amp,
More information800 MHz, 4:1 Analog Multiplexer ADV3221/ADV3222
8 MHz, : Analog Multiplexer ADV/ADV FEATURES Excellent ac performance db bandwidth 8 MHz ( mv p-p) 7 MHz ( V p-p) Slew rate: V/μs Low power: 7 mw, VS = ± V Excellent video performance MHz,. db gain flatness.%
More informationSingle-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822
Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 3 V
More informationDual Picoampere Input Current Bipolar Op Amp AD706
Dual Picoampere Input Current Bipolar Op Amp FEATURES High DC Precision V Max Offset Voltage.5 V/ C Max Offset Drift 2 pa Max Input Bias Current.5 V p-p Voltage Noise,. Hz to Hz 75 A Supply Current Available
More informationSingle-Supply 42 V System Difference Amplifier AD8205
Single-Supply 42 V System Difference Amplifier FEATURES Ideal for current shunt applications High common-mode voltage range 2 V to +65 V operating 5 V to +68 V survival Gain = 50 Wide operating temperature
More informationAD89/AD83/AD84 TABLE OF CONTENTS Specifications... 3 Specifications with ±5 V Supply... 3 Specifications with +5 V Supply... 4 Specifications with +3
Low Power, High Speed Rail-to-Rail Input/Output Amplifier AD89/AD83/AD84 FEATURES Low power.3 ma supply current/amplifier High speed 5 MHz, db bandwidth (G = +) 6 V/µs slew rate 8 ns settling time to.%
More informationZero Drift, Unidirectional Current Shunt Monitor AD8219
Zero Drift, Unidirectional Current Shunt Monitor FEATURES High common-mode voltage range 4 V to 8 V operating.3 V to +85 V survival Buffered output voltage Gain = 6 V/V Wide operating temperature range:
More informationSingle-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820
Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5
More informationHigh Common-Mode Voltage, Programmable Gain Difference Amplifier AD628
High Common-Mode Voltage, Programmable Gain Difference Amplifier AD628 FEATURES FUNCTIONAL BLOCK DIAGRAM High common-mode input voltage range ±20 V at VS = ±5 V Gain range 0. to 00 Operating temperature
More informationUltraprecision Operational Amplifier OP177
Ultraprecision Operational Amplifier FEATURES Ultralow offset voltage TA = 25 C, 25 μv maximum Outstanding offset voltage drift 0. μv/ C maximum Excellent open-loop gain and gain linearity 2 V/μV typical
More informationHigh Voltage, Current Shunt Monitor AD8215
High Voltage, Current Shunt Monitor AD825 FEATURES ±4 V HBM ESD High common-mode voltage range 2 V to +65 V operating 3 V to +68 V survival Buffered output voltage Wide operating temperature range 8-Lead
More informationDual/Quad Low Power, High Speed JFET Operational Amplifiers OP282/OP482
Dual/Quad Low Power, High Speed JFET Operational Amplifiers OP22/OP42 FEATURES High slew rate: 9 V/µs Wide bandwidth: 4 MHz Low supply current: 2 µa/amplifier max Low offset voltage: 3 mv max Low bias
More information16 V Rail-to-Rail, Zero-Drift, Precision Instrumentation Amplifier AD8230
V Rail-to-Rail, Zero-Drift, Precision Instrumentation Amplifier AD FEATURES Resistor programmable gain range: to Supply voltage range: ± V to ± V, + V to + V Rail-to-rail input and output Maintains performance
More informationAD8218 REVISION HISTORY
Zero Drift, Bidirectional Current Shunt Monitor FEATURES High common-mode voltage range 4 V to 8 V operating.3 V to 85 V survival Buffered output voltage Gain = 2 V/V Wide operating temperature range:
More informationADA4857-1/ADA Ultralow Distortion, Low Power, Low Noise, High Speed Op Amp. Data Sheet FEATURES CONNECTION DIAGRAMS APPLICATIONS
5 6 7 8 6 5 4 FEATURES High speed 85 MHz, db bandwidth (G =, RL = kω, LFCSP) 75 MHz, db bandwidth (G =, RL = kω, SOIC) 8 V/μs slew rate Low distortion: 88 dbc at MHz (G =, RL = kω) Low power: 5 ma/amplifier
More informationHigh Common-Mode Voltage Programmable Gain Difference Amplifier AD628
High Common-Mode Voltage Programmable Gain Difference Amplifier FEATURES High common-mode input voltage range ±12 V at VS = ±15 V Gain range.1 to 1 Operating temperature range: 4 C to ±85 C Supply voltage
More informationSelf-Contained Audio Preamplifier SSM2019
a FEATURES Excellent Noise Performance:. nv/ Hz or.5 db Noise Figure Ultra-low THD:
More informationPrecision, Very Low Noise, Low Input Bias Current Operational Amplifiers
Data Sheet Precision, Very Low Noise, Low Input Bias Current Operational Amplifiers AD8671/AD8672/AD8674 FEATURES Very low noise: 2.8 nv/ Hz, 77 nv p-p Wide bandwidth: 1 MHz Low input bias current: 12
More informationLow Power, Wide Supply Range, Low Cost Difference Amplifiers, G = ½, 2 AD8278/AD8279
Low Power, Wide Supply Range, Low Cost Difference Amplifiers, G = ½, 2 /AD8279 FEATURES Wide input range beyond supplies Rugged input overvoltage protection Low supply current: 2 μa maximum (per amplifier)
More informationHigh Voltage, Current Shunt Monitor AD8215
FEATURES ±4 V human body model (HBM) ESD High common-mode voltage range V to +6 V operating 3 V to +68 V survival Buffered output voltage Wide operating temperature range 8-Lead SOIC: 4 C to + C Excellent
More informationUltralow Offset Voltage Dual Op Amp AD708
Ultralow Offset Voltage Dual Op Amp FEATURES Very high dc precision 30 μv maximum offset voltage 0.3 μv/ C maximum offset voltage drift 0.35 μv p-p maximum voltage noise (0. Hz to 0 Hz) 5 million V/V minimum
More informationDual, Ultralow Distortion, Ultralow Noise Op Amp AD8599
Dual, Ultralow Distortion, Ultralow Noise Op Amp FEATURES Low noise: 1 nv/ Hz at 1 khz Low distortion: 5 db THD @ khz
More informationOBSOLETE. Parameter AD9621 AD9622 AD9623 AD9624 Units
a FEATURES MHz Small Signal Bandwidth MHz Large Signal BW ( V p-p) High Slew Rate: V/ s Low Distortion: db @ MHz Fast Settling: ns to.%. nv/ Hz Spectral Noise Density V Supply Operation Wideband Voltage
More informationHigh Speed, Low Noise Video Op Amp AD829
High Speed, Low Noise Video Op Amp AD89 FEATURES High speed MHz bandwidth, gain = V/μs slew rate 9 ns settling time to.% Ideal for video applications.% differential gain. differential phase Low noise.7
More informationHigh Resolution, Zero-Drift Current Shunt Monitor AD8217
High Resolution, Zero-Drift Current Shunt Monitor AD8217 FEATURES High common-mode voltage range 4.5 V to 8 V operating V to 85 V survival Buffered output voltage Wide operating temperature range: 4 C
More informationSingle-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822
Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 3 V to
More informationDual Picoampere Input Current Bipolar Op Amp AD706
Dual Picoampere Input Current Bipolar Op Amp FEATURES High DC Precision V Max Offset Voltage.5 V/ C Max Offset Drift 2 pa Max Input Bias Current.5 V p-p Voltage Noise,. Hz to Hz 75 A Supply Current Available
More informationPrecision Micropower Single Supply Operational Amplifier OP777
a FEATURES Low Offset Voltage: 1 V Max Low Input Bias Current: 1 na Max Single-Supply Operation: 2.7 V to 3 V Dual-Supply Operation: 1.35 V to 15 V Low Supply Current: 27 A/Amp Unity Gain Stable No Phase
More informationHigh Common-Mode Voltage, Programmable Gain Difference Amplifier AD628
High Common-Mode Voltage, Programmable Gain Difference Amplifier FEATURES High common-mode input voltage range ±2 V at VS = ± V Gain range. to Operating temperature range: 4 C to ±8 C Supply voltage range
More informationSingle-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822
Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp FEATURES True Single-Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single-Supply Capability from 3 V to 36
More informationHigh Voltage Current Shunt Monitor AD8212
High Voltage Current Shunt Monitor FEATURES Adjustable gain High common-mode voltage range 7 V to 65 V typical 7 V to >500 V with external pass transistor Current output Integrated 5 V series regulator
More informationHigh Common-Mode Voltage Difference Amplifier AD629
a FEATURES Improved Replacement for: INAP and INAKU V Common-Mode Voltage Range Input Protection to: V Common Mode V Differential Wide Power Supply Range (. V to V) V Output Swing on V Supply ma Max Power
More informationADA4857-1/ADA Ultralow Distortion, Low Power, Low Noise, High Speed Op Amp. Data Sheet FEATURES CONNECTION DIAGRAMS APPLICATIONS
OUT 5 V S 6 PD 7 FB 8 FB PD FEATURES High speed 85 MHz, db bandwidth (G =, RL = kω, LFCSP) 75 MHz, db bandwidth (G =, RL = kω, SOIC) 8 V/µs slew rate Low distortion: 88 dbc @ MHz (G =, RL = kω) Low power:
More informationMicropower Precision CMOS Operational Amplifier AD8500
Micropower Precision CMOS Operational Amplifier AD85 FEATURES Supply current: μa maximum Offset voltage: mv maximum Single-supply or dual-supply operation Rail-to-rail input and output No phase reversal
More informationUltraprecision, 36 V, 2.8 nv/ Hz Dual Rail-to-Rail Output Op Amp AD8676
FEATURES Very low voltage noise 2.8 nv/ Hz @ khz Rail-to-rail output swing Low input bias current: 2 na maximum Very low offset voltage: 2 μv typical Low input offset drift:.6 μv/ C maximum Very high gain:
More informationDual, High Voltage Current Shunt Monitor AD8213
Dual, High Voltage Current Shunt Monitor AD823 FEATURES ±4 V HBM ESD High common-mode voltage range 2 V to +6 V operating 3 V to +68 V survival Buffered output voltage Wide operating temperature range
More information150 μv Maximum Offset Voltage Op Amp OP07D
5 μv Maximum Offset Voltage Op Amp OP7D FEATURES Low offset voltage: 5 µv max Input offset drift:.5 µv/ C max Low noise:.25 μv p-p High gain CMRR and PSRR: 5 db min Low supply current:. ma Wide supply
More informationLow Cost, Dual, High Current Output Line Driver with Shutdown ADA4311-1
Low Cost, Dual, High Current Output Line Driver with Shutdown ADA4311-1 FEATURES High speed 3 db bandwidth: 310 MHz, G = +5, RLOAD = 50 Ω Slew rate: 1050 V/μs, RLOAD = 50 Ω Wide output swing 20.6 V p-p
More informationSingle-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822
Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 3 V
More informationLow Power. Video Op Amp with Disable AD810 REV. A. Closed-Loop Gain and Phase vs. Frequency, G = +2, R L = 150, R F = 715 Ω
CLOSED-LOOP db SHIFT Degrees DIFFERENTIAL % DIFFERENTIAL Degrees a FEATURES High Speed MHz Bandwidth ( db, G = +) MHz Bandwidth ( db, G = +) V/ s Slew Rate ns Settling Time to.% ( = V Step) Ideal for Video
More informationQuad Low Offset, Low Power Operational Amplifier OP400
Quad Low Offset, Low Power Operational Amplifier OP4 FEATURES Low input offset voltage 5 μv max Low offset voltage drift over 55 C to 25 C,.2 pv/ C max Low supply current (per amplifier) 725 μa max High
More informationTABLE OF CONTENTS Features... Applications... Pin Configurations... General Description... Revision History... 2 Specifications... 3 Absolute Maximum
FEATURES Offset voltage: 2.5 mv maximum Single-supply operation: 2.7 V to 5.5 V Low noise: 8 nv/ Hz Wide bandwidth: 24 MHz Slew rate: V/μs Short-circuit output current: 2 ma No phase reversal Low input
More informationKM4110/KM mA, Low Cost, +2.7V & +5V, 75MHz Rail-to-Rail Amplifiers
+ + www.fairchildsemi.com KM411/KM41.5mA, Low Cost, +.7V & +5V, 75MHz Rail-to-Rail Amplifiers Features 55µA supply current 75MHz bandwidth Power down to I s = 33µA (KM41) Fully specified at +.7V and +5V
More informationQuad 7 ns Single Supply Comparator AD8564
Quad 7 ns Single Supply Comparator AD8564 FEATURES 5 V single-supply operation 7 ns propagation delay Low power Separate input and output sections TTL/CMOS logic-compatible outputs Wide output swing TSSOP,
More informationSingle-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822
Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD8 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5 V to
More informationGeneral-Purpose CMOS Rail-to-Rail Amplifiers AD8541/AD8542/AD8544
General-Purpose CMOS Rail-to-Rail Amplifiers AD854/AD8542/AD8544 FEATURES Single-supply operation: 2.7 V to 5.5 V Low supply current: 45 μa/amplifier Wide bandwidth: MHz No phase reversal Low input currents:
More informationUltralow Offset Voltage Operational Amplifier OP07
Ultralow Offset Voltage Operational Amplifier OP07 FEATURES Low VOS: 75 μv maximum Low VOS drift:.3 μv/ C maximum Ultrastable vs. time:.5 μv per month maximum Low noise: 0.6 μv p-p maximum Wide input voltage
More informationHigh Voltage Current Shunt Monitor AD8211
High Voltage Current Shunt Monitor AD8211 FEATURES Qualified for automotive applications ±4 V HBM ESD High common-mode voltage range 2 V to +65 V operating 3 V to +68 V survival Buffered output voltage
More informationPrecision, Low Power, Micropower Dual Operational Amplifier OP290
a FEATURES Single-/Dual-Supply Operation, 1. V to 3 V,. V to 1 V True Single-Supply Operation; Input and Output Voltage Ranges Include Ground Low Supply Current (Per Amplifier), A Max High Output Drive,
More information4 MHz, 7 nv/ Hz, Low Offset and Drift, High Precision Amplifier ADA EP
Enhanced Product FEATURES Low offset voltage and low offset voltage drift Maximum offset voltage: 9 µv at TA = 2 C Maximum offset voltage drift:.2 µv/ C Moisture sensitivity level (MSL) rated Low input
More information16 V, 4 MHz RR0 Amplifiers AD8665/AD8666/AD8668
6 V, MHz RR Amplifiers AD8665/AD8666/AD8668 FEATURES Offset voltage:.5 mv max Low input bias current: pa max Single-supply operation: 5 V to 6 V Dual-supply operation: ±.5 V to ±8 V Low noise: 8 nv/ Hz
More informationDual Picoampere Input Current Bipolar Op Amp AD706. Data Sheet. Figure 1. Input Bias Current vs. Temperature
Data Sheet Dual Picoampere Input Current Bipolar Op Amp Rev. F Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by
More informationUltralow Input Bias Current Operational Amplifier AD549
Ultralow Input Bias Current Operational Amplifier AD59 FEATURES Ultralow input bias current 60 fa maximum (AD59L) 250 fa maximum (AD59J) Input bias current guaranteed over the common-mode voltage range
More informationSingle Supply, High Speed, Rail-to-Rail Output, Triple Op Amp ADA4855-3
FEATURES Voltage feedback architecture Rail-to-rail output swing:. V to 4.9 V High speed amplifiers 4 MHz, 3 db bandwidth, G = 2 MHz, 3 db bandwidth, G = 2 Slew rate: 87 V/µs 53 MHz,. db large signal flatness
More informationUltraprecision, 36 V, 2.8 nv/ Hz Dual Rail-to-Rail Output Op Amp AD8676
Ultraprecision, 36 V, 2. nv/ Hz Dual Rail-to-Rail Output Op Amp AD676 FEATURES Very low voltage noise: 2. nv/ Hz @ khz Rail-to-rail output swing Low input bias current: 2 na maximum Very low offset voltage:
More informationLow Cost Low Power Instrumentation Amplifier AD620
Low Cost Low Power Instrumentation Amplifier AD60 FEATURES Easy to use Gain set with one external resistor (Gain range to 0,000) Wide power supply range (±.3 V to ±8 V) Higher performance than 3 op amp
More informationZero Drift, Digitally Programmable Instrumentation Amplifier AD8231-EP OP FUNCTIONAL BLOCK DIAGRAM FEATURES ENHANCED PRODUCT FEATURES
Zero Drift, Digitally Programmable Instrumentation Amplifier AD8231-EP FEATURES Digitally/pin-programmable gain G = 1, 2, 4, 8, 16, 32, 64, or 128 Specified from 55 C to +125 C 5 nv/ C maximum input offset
More information