POLAR BEAR. by Barb Halvorson

Transcription

1 POLAR BEAR by Barb Halvorson EXCLUSIVE

2 Polar Bear by Barb Halvorson PALETTE Buttermilk #13003 Traditional Burnt Umber #13221 Lamp (Ebony) Black #13067 Lavender #13034 Light Buttermilk #13164 Slate Grey #13068 Turquoise Blue #13258 Warm White #13239 Wedgewood Blue #13038 Yellow Ochre #13008 SURFACE Basswood Country Round Large #63288 MISC. SUPPLIES Royal Palette Paper 40 sheets #70560 Large Sanding Pad Fine/Medium #70796 Gray Graphite Paper 18x36 #70141 Tack Cloth 18 x 36 #70104 Pro Art Tracing Pad #83176 Paper towels Sanding paper MEDIUMS DecoArt Multi Purpose Sealer #87392 DecoArt Drying Time Extender* To keep your paint wet use a drop of DecoArt Drying Time in each puddle of paint or pick up a little on your brush as you paint. Media Gesso White #87415 Dura Clear Satin Varnish #87394 Blue Mix: Warm White + Ultramarine Blue + Lamp Black to grey the blue down. Purple Mix: Lavender + Wedgewood Blue + a touch of Lamp Black. Add Warm White to lighten. A sample of the color is shown on the worksheet. *Discontinued by DecoArt BRUSHES 2 inch foam brush (from set #87423) Papillon by the Artists Club Round size 2 #20158 Round size 6 #20163 Liner size 0 #20146 Glaze Wash size 1 inch #20103 Comb 3 Piece set #20154 PREPARATION Sand and seal the Wood Round with DecoArt Multi Purpose Sealer. Once this is dry wipe away any sanding dust with the Tack Cloth. Basecoat the front of the piece with two coats of gesso using the sponge brushes. Sand lightly between coats. Next basecoat with one coat of Slate Grey. This does not have to be fully covered. Sand lightly again. Transfer the pattern lines with Grey Graphite paper. At the end finish with several coats of Dura Clear Satin Varnish. Basecoat with two coats of Slate Grey, apply your pattern with Grey Graphite. Note from the Artist: This piece is not hard to do; however, white objects are harder to paint. If you were to paint a pure white subject with the color white you would not see it. You may notice a build-up of paint on my sample; I kept going over and over it trying to put more color into it. For those of you that float (I don t) there are areas that would work very well for floating rather than building up large amounts of paint. I have enclosed a worksheet. Please follow it carefully. I have put three colors on the left side, these are the three color mixes I used most often. PAINTING INSTRUCTIONS Eyes, Nose, and Mouth Paint the eyes, nose, and mouth with Lamp Black. Add the dash and dot with Slate Grey. This is shown on the worksheet. Use a small round or liner brush. Paint the nose Lamp Black. Paint the dash with the Blue Mix then follow with a brighter highlight on the center with Warm White. Fill in the mouth with Lamp Black, shadow on the bottom of the nose with Slate Grey and a touch of Lamp Black. I added a touch of Traditional Burnt Umber above the nose as seen on the worksheet, the Purple Mix on the right side of the nose and the Blue Mix on the left side. Add some longer hairs on the bottom of the mouth (chin area) using the horizontal part of the 1/4 inch comb brush with Warm White. Basing in Light and Dark Areas Make sure before you base in the bear you let a little of the pattern lines show. Base the right side of the bear with the Purple Mix and the light side with the Blue Mix. It is fine if some of the Slate Grey basecoat shows through. Remember to pay close attention to the natural growth direction and length of the hairs on the bear. Let the base color tack up a bit and start adding individual clumps of hair with the rake brush. On the right side of the face I used lighter shades of the Purple Mix + Warm White and on the left side I added Warm White to the Blue Mix. As you can see 2 artistsclub.com

3 artistsclub.com 3

4 I have a build-up of paint although that was not my intention. I sanded between coats and kept layering. I guess I forgot I was not painting on a canvas : I added Light Buttermilk to the right side and Warm White to the left side. I added touches of Turquoise with Warm White mainly on the left side and just a touch on the right side. I kept layering individual hairs and defined the white folds with Warm White on both sides of the Polar bear. I used the flat of the 1/4 inch Comb Brush for the shorter folds on the face and the chisel edge of the 1/2 inch brush for the longer hairs on the shoulder area. White Patches Around the Eyes Watch the stroke direction very carefully and using the ¼ inch rake start pulling individual White hair strokes in toward the edges of the patches. Add touches of the Blue Mix, Purple Mix with Warm White. Add just a touch of Traditional Burnt Umber in the corners of the eye. Use touches of Buttermilk to the left side. Ears Base in the ears with Lamp Black. On the tops of the ears I used heavier white paint and pulled individual hairs with a 1/4 inch Comb brush. To put the hairs inside the ears, take the chisel edge of the 1/4 inch Comb brush and stroke in the correct direction. Follow the sample. Claws I did not make detailed claws on this project, only an indication. Follow the worksheet Indication of Claws. Add a Black curved lines for the claws and add Warm White to the center of the claws. Cover them with hair folds using the 1/2 inch Comb Brush with downward strokes and at an angle. Rock in front There is a rock foundation that the polar bear is laying on. I debated between Slate Grey or Traditional Burnt Umber. I ended up trying both colors but chose the brown to match the edges of the wood round. I just color booked since in with a #8 flat brush and highlighted it in the center with a dash of Warm White while the Traditional Burnt Umber was still wet. Underneath the claws of the bear shadow with Wedgewood Blue. FINISHING Allow the wood round to dry. Repeat steps as necessary and varnish. Thanks for allowing me to share this piece with you. 4 artistsclub.com

5 artistsclub.com 5

6 6 artistsclub.com

7 artistsclub.com 7

8 8 artistsclub.com

9 Pattern at 100% 1" x 1" To ensure your pattern is at 100%, this box should measure 1" x 1" when printed. artistsclub.com 9

10 10 artistsclub.com

11 Pattern at 100% 1" x 1" To ensure your pattern is at 100%, this box should measure 1" x 1" when printed. artistsclub.com 11

12 Copyright 2018 by Barb Halvorson and Crafts Group, LLC. All Rights Reserved. # No. *A332432* Artist s Club. All rights reserved. For private, non-commercial use only. Please see our web site for terms of use.