Rigid, Modular Workholding Pallets & Towers

Transcription

1 Rigid, Modular Workholding Pallets & Towers Unique SeraLock and WedgeLock Designs For Ultimate Precision, High Density Workholding

2 Seralock & Wedgelock Kurt s newest family of modular workholding... The SeraLock Towers, SeraLock Pallets and WedgeLock Module system are the latest innovation for achieving high density, highly repeatable part clamping. SeraLock Towers and SeraLock Pallets are designed with interlocking V shaped serrated surfaces for precise and repeatable alignment of WedgeLock clamping modules. SeraLock Towers are available in four sided, two sided and single sided towers with a base that will mount to your HMC or an indexer for VMC applications. SeraLock pallets are available in sizes that will accommodate most vertical machining centers. A custom, high density workholding system can be configured quickly when our WedgeLock modular system of single and double sided clamping jaws are used with the SeraLock Tower or SeraLock Pallet. Check these SeraLock features: Self-aligning Multiple components may be used at the same time Like and unlike workpieces may be machined all in the same setup Mix and match components Allows creation of the equivalent of a custom fixture in less time than the custom fixture can be designed Modular components can be used over and over again Very economical Page 1

3 High Density Workholding Accuracy To The Ultimate Kurt SeraLock Towers and SeraLock Pallets are workholding systems that can be easily configured into custom fixtures utilizing WedgeLock modular components. These systems give you the advantage of building a custom workholding fixture utilizing standard modular components. The SeraLock Tower installation pictured at the right was setup with WedgeLocks to hold twelve parts to be machined. The parts being clamped are a member of a family of parts of various sizes. The manufacturer of these parts can change the setup to accommodate all sizes of parts within the family in a matter of minutes. The exclusive Kurt SeraLock mounting surfaces are the key to the quick, easy setups when changing over from one part to another. The mounting surfaces of the Kurt SeraLock allow quick, repeatable accuracy when repositioning modular clamping elements such as the WedgeLock. The serrations on the mounting surfaces of Kurt SeraLock products align and locate SeraLock clamping elements with accuracy and the speed needed in today s manufacturing environment. And because of the versatility inherent in the system, setups ranging from extremely high-density loads of small parts to single station configurations for very large workpieces can be accommodated on the same workholding surface. High density Key to the SeraLock system is the accuracy of the serrations in form and spacing. The serrations are a perfect match for both clamping surface (tower or subplate) and clamping module (clamps and stationary jaws). The spacing, or pitch, of the serrations allows the use of a variety of economical, short stroke clamping elements. The movable and stationary components of the clamp can be located relative to one another on the subplate or tower so that the needed stroke of the movable component need be little more than the pitch serration. Accuracy to the Ultimate Page 2

4 VMC SeraLock Pallet System Start with this Pallet + Add combinations of WedgeLock components Single clamp Contains stationary jaw on one side and movable jaw on back side. Primarily used for vertical surfaces. Provides 5000 lbs. clamping force at 70 ft. lbs. torque. Double clamp Contains two movable jaws. Used with stationary block to become a high density workholding solution. Clamp two parts with one screw. Provides 5000 lbs. clamping force at 70 ft. lbs. torque. Stationary block Used with single or double clamp. = Stationary block (double) Use when double clamps are used side by side. Dividing Jaw Use in between movable and stationary jaw when milling several identical parts. Jaw floats to accommodate slight part difference. Allows several parts to be clamped with one movable jaw. Page 3

5 HMC SeraLock Tower System Add combinations of WedgeLock components Single clamp Contains stationary jaw on one side and movable jaw on back side. Primarily used for vertical surfaces. Provides 5000 lbs. clamping force at 70 ft. lbs. torque. + Start with this Tower Double clamp Contains two movable jaws. Used with stationary block to become a high density workholding solution. Clamp two parts with one screw. Provides 5000 lbs. clamping force at 70 ft. lbs. torque. Stationary block Used with single or double clamp. Stationary block (double) Use when double clamps are used side by side. = Dividing Jaw Use in between movable and stationary jaw when milling several identical parts. Jaw floats to accommodate slight part difference. Allows several parts to be clamped with one movable jaw. Page 4

6 SeraLock Tower Options Tower Options Tower & Base Options SeraLock Base Options Base length options Base T-slot options Page 5

7 WedgeLock Clamping Options.144 STROKE SINGLE CLAMP WITH STATIONARY JAW 1.25 WIDE BODY SWSC1.144 STROKE SWDC1 DOUBLE CLAMP 1.25 WIDE BODY SWSB1 STATIONARY BLOCK 1.25 WIDE BODY DOUBLE STATIONARY BLOCK SWDSB DIVIDING JAW 1.25 WIDE BODY.125(JAW FLOAT) BOTH WAYS FROM CENTER SWDJ1 Page 6

8 WedgeLock Accessories JAW PLATES STANDARD LENGTH PARALLELS STANDARD LENGTH FLAT JAW PLATE W/M AGNET SWSC1-7-M AG X.500 X STEPPED/REVERSIBLE JAW PLATE SWSC C'BORED FOR #10 SHCS.125 X.625 X SERRATED JAW PLATE W/M AGNET SWSC1-47-M AG.125 X.750 X CARVABLE/REVERSIBLE ALUMINUM JAW PLATE SWSC WORK STOPS "V" JAW PLATE SWSC " DIA..38-1" DIA. REVERSIBLE WORK STOP SW1RWS Check out the new Kurt workholding website for new products, downloads and more. Kurt Manufacturing Industrial Products Division 1325 Quincy St. NE Minneapolis, MN Phone: (763) Toll Free: (800) Fax: (612) workholding@kurt.com Internet: