ABB3009. High Speed Translator Buffer to LVDS ABB3009 FEATURES PIN CONFIGURATION
|
|
|
- Roderick Blair
- 5 years ago
- Views:
Transcription
1 FEATURES Differential output Single AC coupled input (min. 100mV swing). Input range from DC to 1.0 GHz. 2.5V to 3.3V operation. Available in 8-Pin SOIC or 3x3mm QFN. DESCRIPTION The is a low cost, high performance, high speed, buffer that reproduces any input frequency from DC to 1.0GHz. It provides a pair of differential output. Any input signal with at least 100mV swing can be used as reference signal. This chip is ideal for conversion from sine wave, TTL, CMOS, or PECL to. PIN CONFIGURATION (TOP VIEW) OE^ Note: ^ denotes internal pull up BLOCK DIAGRAM Input Amplifier Esperanza., Rancho Santa Margarita, Ca Ph: Fax: /21/05 Page 1
2 PIN DESCRIPTIONS Name 8pin SOIC 3x3mm QFN Pin number Pin number Type Description 1,3,7 1,2,4,5, 9,13,14,15 P Ground. 5,8 7,10,11,12 P Power supply. 2 3 I Reference input signal. The frequency of this signal will be reproduced at the output (after translation to level). 4 6 O True output. 7 8 O Complementary output. OE N/A 16 I Output enable ( 1 for enable). Internal pull-up (default is 1 ). ELECTRICAL SPECIFICATIONS 1. Absolute Maximum Ratings PARAMETERS SYMBOL MIN. MAX. UNITS Supply Voltage 4.6 V Input Voltage, dc VI V Output Voltage, dc VO V Storage Temperature TS C Ambient Operating Temperature* TA C Junction Temperature TJ 125 C Lead Temperature (soldering, 10s) 260 C ESD Protection, Human Body Model 2 kv Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permanent damage to the device and affect product reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other conditions above the operational limits noted in this specification is not implied. * Note: Operating Temperature is guaranteed by design for all parts (COMMERCIAL and INDUSTRIAL), but tested for COMMERCIAL grade only. 2. AC Specifications PARAMETERS CONDITIONS MIN. TYP. MAX. UNITS Input Frequency MHz Input signal swing input 100 mv Output Frequency MHz Esperanza., Rancho Santa Margarita, Ca Ph: Fax: /21/05 Page 2
3 3. Electrical Characteristics PARAMETERS SYMBOL CONDITIONS MIN. TYP. MAX. UNITS Output Differential Voltage VOD mv Magnitude Change VOD mv Output High Voltage VOH RL = 100 Ω V Output Low Voltage VOL (see figure) V Offset Voltage VOS V Offset Magnitude Change VOS mv Power-off Leakage IOXD Vout = or V DD = 0V ±1 ±10 ua Output Short Circuit Current IOSD ma 4. Switching Characteristics PARAMETERS SYMBOL CONDITIONS MIN. TYP. MAX. UNITS Differential Clock Rise Time tr RL = 100 Ω ns Differential Clock Fall Time tf CL = 10 pf (see figure) ns Levels Test Circuit Switching Test Circuit 50Ω C L = 10pF V OD V OS V DIFF R L = 100Ω 50Ω C L = 10pF Transistion Time Waveform 0V (Differential) 80% 80% V DIFF 0V 20% 20% t R t F Esperanza., Rancho Santa Margarita, Ca Ph: Fax: /21/05 Page 3
4 PACKAGE INFORMATION 8 PIN ( dimensions in mm ) Narrow SOIC Symbol Min. Max. A A B C D E H L e 1.27 BSC A 1 e B D C E H L A Esperanza., Rancho Santa Margarita, Ca Ph: Fax: /21/05 Page 4
5 ORDERING INFORMATION For part ordering, please contact our Sales Department: Esperanza., Rancho Santa Margarita, Ca Ph: Fax: PART NUMBER The order number for this device is a combination of the following: Device number, Package type and Operating temperature range S C PART NUMBER TEMPERATURE C=COMMERCIAL I=INDUSTRAL PACKAGE TYPE S=SOIC; Q=QFN Order Number Marking Package Option QC-T A3009QC QFN - Tape and Reel QC A3009QC QFN - Tube SC-T SC SOIC -Tape and Reel SC SC SOIC - Tube Abracon Corporation, reserves the right to make changes in its products or specifications, or both at any time without notice. The information furnished by Abracon is believed to be accurate and reliable. However, Abracon makes no guarantee or warranty concerning the accuracy of said information and shall not be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon this product. LIFE SUPPORT POLICY: Abracon s products are not authorized for use as critical components in life support devices or systems without the express written approval of the President of Abracon Corporation Esperanza., Rancho Santa Margarita, Ca Ph: Fax: /21/05 Page 5
PL High Speed Translator Buffer to LVDS FEATURES PIN CONFIGURATION
FEATURES Differential output Single AC coupled input (min. 100mV swing). Input range from 0 to 1.0GHz. 2.5V to 3.3V operation. Available in 8-Pin SOP or 3x3mm QFN GREEN/RoHS compliant packaging. PIN CONFIGURATION
12-27 MHz XO IC with 1 Pair of LVDS and 1 CMOS Outputs
FETURES Low jitter XO for the 2MHz to 27MHz range. Integrated crystal load capacitor: no external load capacitor required. pair of LVDS outputs and CMOS output. 2-27 MHz fundamental crystal input. Low
[S3,S0] REF_SEL. PLL (Phase Locked Loop)
![[S3,S0] REF_SEL. PLL (Phase Locked Loop)](/thumbs/84/91188749.jpg "[S3,S0] REF_SEL. PLL (Phase Locked Loop)")
ABX02 FEATURES Selectable multipliers (x2.5, x2.75, x3, x4.25, x5, x5.5, x5.75, x6, x6.25, x0, x, x.5, x2, x2.5). Crystal input range, 3MHz to 3MHz (see Selection Table for detailed acceptable input ranges).
OE CLKC CLKT PL PL PL PL602-39
PL602-3x XIN VDD / * SEL0^ / VDD* SEL^ FEATURES Selectable 750kHz to 800MHz range. Low phase noise output -27dBc/Hz for 55.52MHz @ 0kHz offset -5dBc/Hz for 622.08MHz @ 0kHz offset LVCMOS (PL602-37), LVPECL
Dual, 3 V, CMOS, LVDS High Speed Differential Driver ADN4663
Dual, 3 V, CMOS, LVDS High Speed Differential Driver ADN4663 FEATURES ±15 kv ESD protection on output pins 600 Mbps (300 MHz) switching rates Flow-through pinout simplifies PCB layout 300 ps typical differential
PL600-27T CLK0 XIN/FIN 1. Xtal Osc CLK1 XOUT CLK2. Low Power 3 Output XO PIN ASSIGNMENT FEATURES DESCRIPTION CLK2 GND VDD FIN CLK0 SOT23-6L
FEATURES 3 LVCMOS outputs with OE tri -state control Low current consumption: o
PL XIN CLK XOUT VCON. Xtal Osc. Varicap. Low Phase Noise VCXO (17MHz to 36MHz) PIN CONFIGURATION FEATURES DESCRIPTION BLOCK DIAGRAM
FEATURES PIN CONFIGURATION VCXO output for the 17MHz to 36MHz range Low phase noise (-130dBc @ 10kHz offset at 35.328MHz) LVCMOS output with OE tri-state control 17 to 36MHz fundamental crystal input Integrated
19MHz to 800MHz Low Phase-Noise XO PIN CONFIGURATION
PL685-XX FEATURES < 0.5ps RMS phase jitter (12kHz to 20MHz) at 622.08MHz 30ps max peak to peak period jitter Ultra Low-Power Consumption о < 90 ma @622MHz PECL output о
Low-Power, 1.62V to 3.63V, 1MHz to 150MHz, 1:3 Fanout Buffer IC CLK2 VDD CLK0 SOT23-6L
FEATURES 3 LVCMOS Outputs 12mA Output Drive Strength Input/Output Frequency: o Reference Clock: 1MHz to 150MHz Supports LVCMOS or Sine Wave Input Clock Very Low Jitter and Phase Noise Low Current Consumption
Phase Detector. Selectable / 1,/ 2,/4,/8. Selectable / 1,/2
Programming Logic PL611-01 FEATURES Advanced programmable PLL design Very low Jitter and Phase Noise (30-70ps Pk-Pk typical) Up to 3 programmable outputs Output frequency up to 200MHz CMOS. Accepts Crystal
Low-Power, 1.62V to 3.63V, 1MHz To 150MHz, 1:2 Fanout Buffer IC OE CLK1. DFN-6L (2.0 x 1.3 x 0.6mm) FIN CLK1
FEATURES 2 LVCMOS Outputs Input/Output Frequency: 1MHz to 150MHz Supports LVCMOS or Sine Wave Input Clock Extremely low additive Jitter 8 ma Output Drive Strength Low Current Consumption Single 1.8V, 2.5V,
Analog Frequency Multiplier
Analog Frequency Multiplier DESCRIPTION Analog Frequency Multipliers TM (AFMs) are the industry s first Balanced Oscillator utilizing analog multiplication of the fundamental frequency (at double or quadruple
19MHz to 250MHz Low Phase-Noise XO PAD CONFIGURATION
FEATURES < 0.6ps RMS phase jitter (12kHz to 20MHz) at 155.52MHz 30ps max peak to peak period jitter 8bit Switch Capacitor for ±50PPM crystal CLoad tuning о Load Capacitance Tuning Range: 8pF to 12pF Ultra
PO74G139A. Pin Configuration. Logic Block Diagram. Pin Description. 74 Series Noise Cancellation GHz Logic FEATURES: DESCRIPTION:
FEATURES:. Patented technology. Operating frequency up to 1.125GHz with 2pf load. Operating frequency up to 800MHz with 5pf load. Operating frequency up to 350MHz with 15pf load. VCC Operates from 1.65V
PO74G2308A FEATURES: DESCRIPTION: Description. 700MHz TTL/CMOS Potato Chip. BUF_IN OUTPUT 1 to OUTPUT 8. Outputs. 1.2V - 3.6V 1:8 CMOS Clock Driver
FEATURES:. Patented technology. Operating frequency up to 700MHz with 2pf load. Operating frequency up to 550MHz with 5pf load. Operating frequency up to 350MHz with 15pf load. Operating frequency up to
Dual, 3 V, CMOS, LVDS Differential Line Receiver ADN4664
Dual, 3 V, CMOS, LVDS Differential Line Receiver ADN4664 FEATURES ±15 kv ESD protection on output pins 400 Mbps (200 MHz) switching rates Flow-through pinout simplifies PCB layout 100 ps channel-to-channel
3 V, LVDS, Quad, CMOS Differential Line Driver ADN4665
3 V, LVDS, Quad, CMOS Differential Line Driver ADN4665 FEATURES ±15 kv ESD protection on output pins 400 Mbps (200 MHz) switching rates 100 ps typical differential skew 400 ps maximum differential skew
PO54G14A, PO74G14A. Pin Configuration. 54, 74 Series Noise Cancellation GHz Logic FEATURES: DESCRIPTION: V CC 6A 6Y 5A 5Y 4A 4Y 1A 1Y 2A 2Y 3A 3Y GND
FEATURES:. Patented technology. Operating frequency up to 1.125GHz with 2pf load. Operating frequency up to 680MHz with 5pf load. Operating frequency up to 300MHz with 15pf load. Operating frequency up
Low Phase Noise, LVPECL VCXO (for 150MHz to 160MHz Fundamental Crystals) FEATURES. * Internal 60KΩ pull-up resistor
0.952mm VDD QB PL586-55/-58 FEATURES DIE CONFIGURATION Advanced non multiplier VCXO Design for High Performance Crystal Oscillators Input/Output Range: 150MHz to 160MHz Phase Noise Optimized for 155.52MHz:
Features. Applications
PCIe Fanout Buffer 267MHz, 8 HCSL Outputs with 2 Input MUX PrecisionEdge General Description The is a high-speed, fully differential 1:8 clock fanout buffer optimized to provide eight identical output
Single, 3 V, CMOS, LVDS Differential Line Receiver ADN4662
Data Sheet FEATURES ±15 kv ESD protection on input pins 400 Mbps (200 MHz) switching rates Flow-through pinout simplifies PCB layout 2.5 ns maximum propagation delay 3.3 V power supply High impedance outputs
PI90LV031A PI90LV027A PI90LV017A. 3V LVDS High-Speed Differential Line Drivers. Description. Features PI90LV027A PI90LV031A PI90LV017A
PI90LV03A PI90LV027A PI90LV07A 3V LVDS High-Speed Differential Line Drivers Features Signaling Rates >400Mbps (200 MHz) Single 3.3V Power Supply Design ±30mV Differential Swing Maximum Differential Skew
Programmable Low Voltage 1:10 LVDS Clock Driver ADN4670
Data Sheet Programmable Low Voltage 1:10 LVDS Clock Driver FEATURES FUNCTIONAL BLOCK DIAGRAM Low output skew
Low voltage 16-bit constant current LED sink driver with auto power-saving. Description
Low voltage 16-bit constant current LED sink driver with auto power-saving Datasheet - production data Features Low voltage power supply down to 3 V 16 constant current output channels Adjustable output
PI90LV031A. 3V LVDS High-Speed Differential Line Drivers. Description. Features. Applications PI90LV027A PI90LV031A PI90LV017A
P90LV03A P90LV027A P90LV07A 3V LVDS High-Speed Differential Line Drivers Features Signaling Rates >400Mbps (200 MHz) Single 3.3V Power Supply Design ±350mV Differential Swing Maximum Differential Skew
DIFFERENTIAL ECL-to-TTL TRANSLATOR
DIFFERENTIAL ECL-to-TTL TRANSLATOR FEATURES DESCRIPTION 2.6ns typical propagation delay Differential ECL inputs 24mA TTL outputs Flow-through pinouts Available in 8-pin SOIC package The is a differential
ICS LOW PHASE NOISE ZERO DELAY BUFFER AND MULTIPLIER. Description. Features. Block Diagram DATASHEET
DATASHEET ICS670-04 Description The ICS670-04 is a high speed, low phase noise, Zero Delay Buffer (ZDB) which integrates IDT s proprietary analog/digital Phase Locked Loop (PLL) techniques. It is identical
Phase Detector. Charge Pump. F out = F VCO / (4*P)
PL611-30 FEATURES Advanced programmable PLL design Very low Jitter and Phase Noise (< 40ps Pk -Pk typ.) Supports complementary LVCMOS outputs to drive LVPECL and LVDS i nputs. Output Frequencies: o < 400MHz
PL560/ VCXO Family
OSCOFF SEL GNDOSC VCON XIN VDDBUF QBAR Q GNDBUF (Prelim inary ) Analog Frequency Multiplier PRODUCT DESCRIPTION The Analog Frequency Multiplier (AFM) is the industry s first Balanced Oscillator utilizing
PO54G00A, PO74G00A. Pin Configuration. Pin Description. Logic Block Diagram. 54, 74 Series Noise Cancellation GHz Logic FEATURES: DESCRIPTION: V CC 1B
FEATURES:. Patented technology. Specified From 40 C to 85 C, 40 C to 125 C, and 55 C to 125 C. Operating frequency up to 1.125GHz with 2pf load. Operating frequency up to 750MHz with 5pf load. Operating
15 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP
5 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP FEATURES Supports defense and aerospace applications (AQEC standard) Military temperature range ( 55 C to +25 C) Controlled manufacturing baseline
Dual, Ultralow Distortion, Ultralow Noise Op Amp AD8599
Dual, Ultralow Distortion, Ultralow Noise Op Amp FEATURES Low noise: 1 nv/ Hz at 1 khz Low distortion: 5 db THD @ khz
PL565-37/38 VCXO Family
(Preliminary) Analog Frequency Multiplier PRODUCT DESCRIPTION The Analog Frequency Multiplier (AFM) is the industry s first Balanced Oscillator utilizing analog multiplication of the fundamental frequency
STP16CP05. Low voltage 16-bit constant current LED sink driver. Description. Features
Low voltage 16-bit constant current LED sink driver Datasheet - production data Features Low voltage power supply down to 3 V 16 constant current output channels Adjustable output current through external
PL V-3.3V Low-Skew 1-4 Differential PECL Fanout Buffer
-48 FEATURES Four differential 2.5V/3.3V LVPECL output pairs. Output Frequency: 1GHz. Two selectable differential input pairs. Translates any standard single-ended or differential input format to LVPECL
ICS LOW PHASE NOISE CLOCK MULTIPLIER. Features. Description. Block Diagram DATASHEET
DATASHEET ICS601-01 Description The ICS601-01 is a low-cost, low phase noise, high-performance clock synthesizer for applications which require low phase noise and low jitter. It is IDT s lowest phase
10-Channel Gamma Buffer with VCOM Driver ADD8710
1-Channel Gamma Buffer with VCOM Driver ADD871 FEATURES Single-supply operation: 4.5 V to 18 V Upper/lower buffers swing to VS/GND Gamma continuous output current: >1 ma VCOM peak output current: 25 ma
PO74G553A. Pin Configuration. Logic Block Diagram. Pin Description. 800MHz Noise Cancellation TTL/CMOS Potato Chip
FEATURES:. Patented technology. Operating frequency up to 800Mz with 2pf load. Operating frequency up to 600Mz with 5pf load. Operating frequency up to 300Mz with 15pf load. Operating frequency up to 150Mz
CLK1 GND. Phase Detector F VCO = F REF * (2 * M/R) VCO. P-Counter (14-bit) F OUT = F VCO / (2 * P) Programming Logic
PL611s-19 PL611s-19 FEATURES Designed for Very Low-Power applications Input Frequency, AC Coupled: o Reference Input: 1MHz to 125MHz o Accepts >0.1V input signal voltage Output Frequency up to 125MHz LVCMOS
Low-Power 2.25V to 3.63V DC to 150MHz 1:6 Fanout Buffer IC DESCRIPTION
FEATURES 1:6 LVCMOS output fanout buffer for DC to 150MHz 8mA Output Drive Strength Low power consumption for portable applications Low input-output delay Output-Output skew less than 250ps Low Additive
500MHz TTL/CMOS Potato Chip
FEATURES:. Patent pending technology. Max input frequency > 1GHz. Operating frequency up to 500MHz with 2pf load. Operating frequency up to 450MHz with 5pf load. Operating frequency up to 300MHz with 15pf
ICS LOW PHASE NOISE ZERO DELAY BUFFER AND MULTIPLIER. Description. Features. Block Diagram DATASHEET
DATASHEET ICS670-02 Description The ICS670-02 is a high speed, low phase noise, Zero Delay Buffer (ZDB) which integrates IDT s proprietary analog/digital Phase Locked Loop (PLL) techniques. Part of IDT
AS393/393A. Description. Pin Assignments. Features. Applications. Typical Applications Circuit LOW POWER LOW OFFSET VOLTAGE DUAL COMPARATORS
LOW POWER LOW OFFSET VOLTAGE DUAL COMPARATORS Description Pin Assignments The consist of two independent precision voltage comparators with a typical offset voltage of 1.0mV and high gain. They are specifically
SGM8706 Micro-Power, RRIO, 1.8V, Push-Pull Output Comparator with Integrated Voltage Reference GENERAL DESCRIPTION FEATURES APPLICATIONS
Micro-Power, RRIO, 1.V, Push-Pull Output GENERAL DESCRIPTION The is a low power comparator with a typical power supply current of 2.2µA. It features an uncommitted on-chip voltage reference, comparator
Description. Benefits CONTROL LOGIC. Rev 1.2, December 21, 2010 Page 1 of 12
3-Channel Clock Distribution Buffer Key Features Low current consumption: - 2.7mA-typ (VDD=1.8V, CL=0) 1.70V to 3.65V power supply operation MHz to 52MHz CLKIN range Supports LVCMOS or Sine Inputs Supports
Ultraprecision, 36 V, 2.8 nv/ Hz Dual Rail-to-Rail Output Op Amp AD8676
FEATURES Very low voltage noise 2.8 nv/ Hz @ khz Rail-to-rail output swing Low input bias current: 2 na maximum Very low offset voltage: 2 μv typical Low input offset drift:.6 μv/ C maximum Very high gain:
Low Power Hex ECL-to-TTL Translator
Low Power Hex ECL-to-TTL Translator General Description The 100325 is a hex translator for converting F100K logic levels to TTL logic levels. Differential inputs allow each circuit to be used as an inverting,
NOT RECOMMENDED FOR NEW DESIGNS
NOT RECOMMENDED FOR NEW DESIGNS 3.3V, DUAL DIFFERENTIAL LVPECL-TO-LVTTL TRANSLATOR FEATURES 3.3V power supply 2.0ns typical propagation delay
(Prelim inary ) Analog Frequency Multiplier. Oscillator Amplifier
OSCOFF SEL GNDOSC VCON XIN VDDBUF QBAR Q GNDBUF (Prelim inary ) Analog Frequency Multiplier PRODUCT DESCRIPTION The Analog Frequency Multiplier (AFM) is the industry s first Balanced Oscillator utilizing
3.3V CMOS 16-BIT REGISTER (3-STATE)
3. CMOS 16-BIT REGISTER (3-STATE) 3. CMOS 16-BIT REGISTER (3-STATE) IDT74FCT163374A/C FEATURES: 0.5 MICRON CMOS Technology Typical tsk(o) (Output Skew) < 250ps ESD > 200 per MIL-STD-883, Method 3015; >
3.3V CMOS 20-BIT BUFFER
3. CMOS 20-BIT BUFFER 3. CMOS 20-BIT BUFFER IDT74FCT163827A/C FEATURES: 0.5 MICRON CMOS Technology Typical tsk(o) (Output Skew) < 250ps ESD > 200 per MIL-STD-883, Method 3015; > 20 using machine model
SY88993AL. Features. General Description. Applications. Markets. 3.3V 3.2Gbps High-Speed Limiting Post Amplifier with High Input Sensitivity
3.3V 3.2Gbps High-Speed Limiting Post Amplifier with High Input Sensitivity General Description The limiting post amplifier, with its wide bandwidth, is ideal for use as a post amplifier in fiber-optic
AS339/339A. Description. Pin Assignments. Features. Applications LOW POWER LOW OFFSET VOLTAGE QUAD COMPARATORS AS339/339A
LOW POWER LOW OFFSET VOLTAGE QUAD COMPARATORS Description Pin Assignments The consist of four independent precision voltage comparators with a typical offset voltage of 2.0mV and high gain. They are specifically
3.3V ZERO DELAY CLOCK BUFFER, SPREAD SPECTRUM COMPATIBLE
3.3V ZERO DELAY CLOCK BUFFER, SPREAD SPECTRUM COMPATIBLE IDT23S05 FEATURES: Phase-Lock Loop Clock Distribution 10MHz to 133MHz operating frequency Distributes one clock input to one bank of five outputs
SGM8701 Micro-Power, CMOS Input, RRIO, 1.4V, Push-Pull Output Comparator
SGM871 GENERAL DESCRIPTION The SGM871 is an ultra low power comparator with a typical power supply current of 3nA. It has the best-in-class power supply current versus propagation delay performance. The
PO74G16240A. Pin Configuration. Logic Block Diagram. Truth Table. 74 Series Noise Cancellation GHz Logic DESCRIPTION: FEATURES:
FEATURES:. Patented technology. Operating frequency up to.25ghz with 2pf load. Operating frequency up to 700MHz with 5pf load. Operating frequency up to 300MHz with 5pf load. Operating frequency up to
Features. Applications
267MHz 1:2 3.3V HCSL/LVDS Fanout Buffer PrecisionEdge General Description The is a high-speed, fully differential 1:2 clock fanout buffer with a 2:1 input MUX optimized to provide two identical output
FAST CMOS 16-BIT BIDIRECTIONAL 3.3V TO 5V TRANSLATOR
FAST CMOS 16-BIT BIDIRECTIONAL 3. TO 5V TRANSLATOR FAST CMOS 16-BIT BIDIRECTIONAL 3. TO 5V TRANSLATOR IDT74FCT164245T FEATURES: 0.5 MICRON CMOS Technology Bidirectional interface between 3. and 5V buses
SCM3401A Half-duplex Transceiver
SCM3401A Half-duplex Transceiver Features Package 5.0V single supply operation Baud Rate Up to 1Mbps 1/8 Unit Load Up to 256 Nodes on a Bus Low Quiescent Power 0.3mA Active Mode 50nA Shutdown Mode Bus-Pin
ICS558A-02 LVHSTL TO CMOS CLOCK DIVIDER. Description. Features. Block Diagram DATASHEET
DATASHEET ICS558A-02 Description The ICS558A-02 accepts a high-speed LVHSTL input and provides four CMOS low skew outputs from a selectable internal divider (divide by 3, divide by 4). The four outputs
Features. Applications. Micrel Inc Fortune Drive San Jose, CA USA tel +1 (408) fax + 1 (408)
Flexible Ultra-Low Jitter Clock Synthesizer Clockworks FLEX General Description The SM802xxx series is a member of the ClockWorks family of devices from Micrel and provide an extremely low-noise timing
PCI-EXPRESS CLOCK SOURCE. Features
DATASHEET ICS557-01 Description The ICS557-01 is a clock chip designed for use in PCI-Express Cards as a clock source. It provides a pair of differential outputs at 100 MHz in a small 8-pin SOIC package.
3 V LVDS Quad CMOS Differential Line Driver ADN4667
FEATURES ±15 kv ESD protection on output pins 400 Mbps (200 MHz) switching rates Flow through pinout simplifies PCB layout 300 ps typical differential skew 400 ps maximum differential skew 1.7 ns maximum
ICS571 LOW PHASE NOISE ZERO DELAY BUFFER. Description. Features. Block Diagram DATASHEET
DATASHEET Description The is a high speed, high output drive, low phase noise Zero Delay Buffer (ZDB) which integrates IDT s proprietary analog/digital Phase Locked Loop (PLL) techniques. IDT introduced
Features. Applications. Markets
3.3V, 3.2Gbps PECL Limiting Post Amplifier with Wide Signal-Detect Range General Description The low-power limiting post amplifiers are designed for use in fiber-optic receivers. These devices connect
Note: ^ Deno tes 60K Ω Pull-up resisto r. Phase Detector F VCO = F REF * (M/R) F OUT = F VCO / P
FEATURES Advanced programmable PLL with Spread Spectrum Crystal or Reference Clock input o Fundamental crystal: 10MHz to 40MHz o Reference input: 1MHz to 200MHz Accepts 0.1V reference signal input voltage
1.25Gbps HIGH-SPEED LIMITING POST AMPLIFIER Not recommended for new designs
1.25Gbps HIGH-SPEED LIMITING POST AMPLIFIER Not recommended for new designs FEATURES DESCRIPTION Up to 1.25Gbps operation Low noise Chatter-Free Generation Open Collector TTL Output TTL /EN Input Differential
FAST CMOS BUFFER CLOCK/DRIVER
FAST CMOS BUFFER CLOCK/DRIVER IDT49FCT806BT/CT FEATURES: 0. MICRON CMOS Technology Guaranteed low skew < 00ps (max.) Very low duty cycle distortion < 600ps (max.) Low CMOS power levels TTL compatible inputs
Low Power, Rail-to-Rail Output, Precision JFET Amplifiers AD8641/AD8642/AD8643
Data Sheet Low Power, Rail-to-Rail Output, Precision JFET Amplifiers AD864/AD8642/AD8643 FEATURES Low supply current: 25 μa max Very low input bias current: pa max Low offset voltage: 75 μv max Single-supply
FAST CMOS 8-BIT IDENTITY COMPARATOR
FAST CMOS 8-BIT IDENTITY COMPARATOR IDT74FCT521AT/CT FEATURES: A and C grades Low input and output leakage 1µA (max.) CMOS power levels True TTL input and output compatibility: VOH = 3. (typ.) VOL = 0.
TSX3702. Micropower dual CMOS voltage comparators. Related products. Applications. Description. Features
Micropower dual CMOS voltage comparators Datasheet - production data Input common-mode voltage range includes ground Push-pull output High input impedance: 10 12 Ω typ Fast response time: 2.7 µs typ. for
IDT74FCT257AT/CT/DT FAST CMOS QUAD 2-INPUT MULTIPLEXER
FAST CMOS QUAD 2-INPUT MULTIPLEXER IDT74FCT257AT/CT/DT FEATURES: A, C, and D grades Low input and output leakage 1µA (max.) CMOS power levels True TTL input and output compatibility: VOH = 3. (typ.) VOL
PO3B402A. High Bandwidth Potato Chip OE1 Y1+ Y1- GND SEL3 SEL1 D3- D3+ OE2 Y2+ Y2- Y3+ M3- M3+ OE3 SEL2 OE3 Y3+ Y3- SEL3 OE4 Y4+ Y4- SEL4
FEATURES: Patented technology High signal -3db passing bandwidth at GHz Near-Zero propagation delay CC =.65 to 3.6 Ultra-Low Quiescent Power: 0.µA typical Ideally suited for low power applications Industrial
Quad, Wide-Bandwidth SPDT Video Analog Switch
GERAL DESCRIPTION The is a Quad, bidirectional, single-pole/doublethrow (SPDT) CMOS Video analog switches (Mux/DeMux) designed to operate at a single +5V supply. This 2-channel multiplexer/demultiplexer
IDT5V60014 LOW PHASE NOISE ZERO DELAY BUFFER. Description. Features. Block Diagram DATASHEET
DATASHEET IDT5V60014 Description The IDT5V60014 is a high speed, high output drive, low phase noise Zero Delay Buffer (ZDB) which integrates IDT s proprietary analog/digital Phase Locked Loop (PLL) techniques.
SGM8705 Micro-Power, CMOS Input, RRIO, 1.4V, Push-Pull Output Comparator
SGM87 Micro-Power, CMOS Input, RRIO, 1.4V, GENERAL DESCRIPTION The SGM87 is a dual low power comparator with a typical power supply current of 3nA (per channel). It has the best-in-class power supply current
2.5Gbps HIGH-SPEED LIMITING POST AMPLIFIER Not recommended for new designs
2.5Gbps HIGH-SPEED LIMITING POST AMPLIFIER Not recommended for new designs FEATURES DESCRIPTION Up to 2.5Gbps operation Low noise Chatter-Free generation Open Collector TTL output TTL /EN Input Differential
5V/3.3V TTL-TO-DIFFERENTIAL PECL TRANSLATOR
5V/3.3V TTL-TO-DIFFERENTIAL PECL TRANSLATOR FEATURES 3.3V and 5V power supply options 300ps typical propagation delay Low power Differential PECL output PNP TTL input for minimal loading Flow-through pinouts
ICS542 CLOCK DIVIDER. Features. Description. Block Diagram DATASHEET. NOTE: EOL for non-green parts to occur on 5/13/10 per PDN U-09-01
DATASHEET ICS542 Description The ICS542 is cost effective way to produce a high-quality clock output divided from a clock input. The chip accepts a clock input up to 156 MHz at 3.3 V and produces a divide
IXYS IXI848A. High-Side Current Monitor. General Description. Features: Applications: Ordering Information. General Application Circuit
High-Side Current Monitor Features: High-Side Current Sense Amplifier 2.7V to 60V Input Range 0.7 Typical Full Scale Accuracy Scalable Output Voltage SOIC Package Applications: Power Management Systems
5V/3.3V DUAL DIFFERENTIAL 2:1 MULTIPLEXER
5V/3.3V DUAL DIFFERENTIAL 2:1 MULTIPLEXER FEATURES DESCRIPTION 3.3V and 5V power supply options 440ps propagation delay Separate and common select High bandwidth output transitions Internal 75KΩ input
AD864/AD8642/AD8643 TABLE OF CONTENTS Specifications... 3 Electrical Characteristics... 3 Absolute Maximum Ratings... 5 ESD Caution... 5 Typical Perfo
FEATURES Low supply current: 25 µa max Very low input bias current: pa max Low offset voltage: 75 µv max Single-supply operation: 5 V to 26 V Dual-supply operation: ±2.5 V to ±3 V Rail-to-rail output Unity-gain
FAST CMOS 16-BIT REGISTER (3-STATE)
FAST CMOS 16-BIT REGISTER (3-STATE) IDT74FCT16374AT/CT/ET FEATURES: 0.5 MICRON CMOS Technology High-speed, low-power CMOS replacement for ABT functions Typical tsk(o) (Output Skew) < 250ps Low input and
Low Power, Precision, Auto-Zero Op Amps AD8538/AD8539 FEATURES Low offset voltage: 13 μv maximum Input offset drift: 0.03 μv/ C Single-supply operatio
Low Power, Precision, Auto-Zero Op Amps FEATURES Low offset voltage: 3 μv maximum Input offset drift:.3 μv/ C Single-supply operation: 2.7 V to 5.5 V High gain, CMRR, and PSRR Low input bias current: 25
DUAL OP AMP AND VOLTAGE REFERENCE General Description. Features
General Description The is a monolithic IC specifically designed to regulate the output current and voltage levels of switching battery chargers and power supplies. The device contains two Op Amps and
SGM8551XN Single-Supply, Single Rail-to-Rail I/O Precision Operational Amplifier
PRODUCT DESCRIPTION The SGM8551XN is a single rail-to-rail input and output precision operational amplifier which has low input offset voltage, and bias current. It is guaranteed to operate from 2.5V to
ICS GLITCH-FREE CLOCK MULITPLEXER. Features. Description. Block Diagram DATASHEET
DATASHEET ICS580-01 Description The ICS580-01 is a clock multiplexer (mux) designed to switch between two clock sources with no glitches or short pulses. The operation of the mux is controlled by an input
IDT74FCT540AT/CT FAST CMOS OCTAL BUFFER/LINE DRIVER DESCRIPTION: FUNCTIONAL BLOCK DIAGRAM FEATURES:
FAST CMOS OCTAL BUFFER/LINE DRIVER IDT74FCT540AT/CT FEATURES: Low input and output leakage 1µ A (max.) CMOS power levels True TTL input and output compatibility VOH = 3. (typ.) VOL = 0. (typ.) Meets or
3.3V DIFFERENTIAL LVPECL-to-LVTTL TRANSLATOR
3.3V DIFFERENTIAL LVPECL-to-LVTTL TRANSLATOR FEATURES 3.3V power supply 2.0ns typical propagation delay Low power Differential LVPECL inputs 24mA TTL outputs Flow-through pinouts Available in 8-pin SOIC
TS3021H. Automotive rail-to-rail 1.8 V high-speed comparator. Related products. Applications. Description. Features SOT23-5
Automotive rail-to-rail 1.8 V high-speed comparator Datasheet - production data Related products TS3021 for standard temperature range (-40 C to 125 C) OUT IN+ 1 2 SOT23-5 + - Features AEC-Q100 and Q003
FAST CMOS OCTAL LATCHED TRANSCEIVER
FAST CMOS OCTAL LATCHED TRANSCEIVER IDT74FCT543AT/CT FEATURES: A and C grades Low input and output leakage 1µA (max.) CMOS power levels True TTL input and output compatibility: VOH = 3. (typ.) VOL = 0.
SY88903AL. General Description. Features. Applications. Markets
3.3V, Burst Mode 1.25Gbps PECL High- Sensitivity Limiting Post Amplifier with TTL Loss-of-Signal General Description The, burst mode, high-sensitivity limiting post amplifier is designed for use in fiber-optic
Rail-to-Rail, High Output Current Amplifier AD8397
Rail-to-Rail, High Output Current Amplifier FEATURES Dual operational amplifier Voltage feedback Wide supply range from 3 V to 24 V Rail-to-rail output Output swing to within.5 V of supply rails High linear
ICS1885. High-Performance Communications PHYceiver TM. Integrated Circuit Systems, Inc. General Description. Pin Configuration.
Integrated Circuit Systems, Inc. ICS1885 High-Performance Communications PHYceiver TM General Description The ICS1885 is designed to provide high performance clock recovery and generation for either 25.92
ICS507-01/02 PECL Clock Synthesizer
Description The ICS507-01 and ICS507-02 are inexpensive ways to generate a low jitter 155.52 MHz (or other high speed) differential PECL clock output from a low frequency crystal input. Using Phase-Locked-
DESCRIPTION CLKA1 CLKA2 CLKA3 CLKA4 CLKB1 CLKB2 CLKB3 CLKB4
PL123-05 PL123-09 FEATURES DESCRIPTION Frequency Range 10MHz to 134 MHz Output Options: o 5 outputs PL123-05 o 9 outputs PL123-09 Zero input - output delay Optional Drive Strength: Standard (8mA) High
BCT MHz DPDT Analog Switch for USB2.0 Hi-Speed
BCT4227 700MHz DPDT Analog Switch for USB2.0 Hi-Speed Features VCC Operating Range: 1.65V to V Rail-to-Rail Signal Range ON-Resistance Matching: 0.05 Ω (TYP) ON-Resistance Flatness: 0.08Ω (TYP) High Off
LOW SKEW 1 TO 4 CLOCK BUFFER. Features
DATASHEET ICS651 Description The ICS651 is a low skew, single input to four output, clock buffer. Part of IDT s ClockBlocks TM family, this is a low skew, small clock buffer. IDT makes many non-pll and
The PL is an advanced Spread Spectrum clock generator (SSCG), and a member of PicoPLL Programmable Clock family.
FEATURES Advanced programmable PLL with Spread Spectrum Reference Clock input o 1MHz to 200MHz Output Frequency o
ICS553 LOW SKEW 1 TO 4 CLOCK BUFFER. Description. Features. Block Diagram DATASHEET
DATASHEET ICS553 Description The ICS553 is a low skew, single input to four output, clock buffer. Part of IDT s ClockBlocks TM family, this is our lowest skew, small clock buffer. See the ICS552-02 for