HIGH SPEED, EXTREMELY LOW NOISE LDO REGULATOR. Features

Transcription

1 General Description The series are positive voltage regulator ICs fabricated by CMOS process. Each of these ICs consists of a voltage reference, an error amplifier, a resistor network for setting output voltage, a current limit circuit for current protection. The series feature high supply voltage ripple rejection, low dropout voltage, low noise, high output voltage accuracy, and low current consumption which make them ideal for use in various battery-powered devices. The series have 1.2, 1.3, 1.5, 1.8, 2.5, 2.8, 3.0, 3.2, 3.3, 3.6, 4.0 and 5.0 versions. The are available in standard SOT-23, SOT-89 and TO-92 packages. Features Low Dropout oltage at I OUT =100mA: 200m Typical (Except 1.2, 1.3 and 1.5 ersions) Low Quiescent Current: 25μA Typical High Ripple Rejection: 65dB Typical (f=1khz) Output Current: More Than 150mA (250mA Limit) Extremely Low Noise: 15μrms@ OUT =1.2, 1.3, 1.5 (10Hz to 100kHz) Excellent Line Regulation: 4m Typical Excellent Load Regulation: 12m Typical High Output oltage Accuracy: ±2% Excellent Line Transient Response and Load Transient Response Compatible with Low ESR Ceramic Capacitor (as Low as 1μF) Applications Mobile Phones, Cordless Phones Wireless Communication Equipment Portable Games Cameras, ideo Recorders Sub-board Power Supplies for Telecom Equipment Battery Powered Equipment SOT-23 SOT-89 TO-92 (Bulk Packing) TO-92 (Ammo Packing) Figure 1. Package Types of 1

2 Pin Configuration N/NA Package (SOT-23) R Package (SOT-89) N NA IN GND GND OUT IN OUT GND IN OUT Z Package (TO-92 (Bulk Packing)) Z Package (TO-92 (Ammo Packing)) 3 OUT 3 OUT 2 IN 2 IN 1 GND 1 GND Figure 2. Pin Configuration of (Top iew) Pin Description Pin Number SOT-23 (N) SOT-23 (NA) SOT-89/ TO-92 Pin Name Function GND Ground OUT Regulated Output oltage IN Input oltage 2

3 Functional Block Diagram IN 3(1){2} 2(2){3} OUT REF CURRENT LIMIT 1(3){1} GND A(B){C} A for SOT-23 (N) B for SOT-23 (NA) C for SOT-89/TO-92 Figure 3. Functional Block Diagram of 3

4 Ordering Information - Circuit Type Package N/NA: SOT-23 R: SOT-89 Z: TO-92 G1: Green TR: Tape and Reel or Ammo Blank: Bulk 1.2: Fixed Output : Fixed Output : Fixed Output : Fixed Output : Fixed Output : Fixed Output : Fixed Output : Fixed Output : Fixed Output : Fixed Output : Fixed Output : Fixed Output 5.0 Package Temperature Range Output oltage Part Number Marking ID Packing Type 1.2(N) N-1.2TRG1 GR4 Tape & Reel 1.3(N) N-1.3TRG1 GR5 Tape & Reel 1.5(N) N-1.5TRG1 GR6 Tape & Reel 1.8(N) N-1.8TRG1 GR7 Tape & Reel 2.5(N) N-2.5TRG1 GR8 Tape & Reel SOT-23 SOT-23 SOT to 85 o C -40 to 85 o C -40 to 85 o C 2.8(N) N-2.8TRG1 GR9 Tape & Reel 3.0(N) N-3.0TRG1 GS2 Tape & Reel 3.2(N) N-3.2TRG1 GS3 Tape & Reel 3.3(N) N-3.3TRG1 GS4 Tape & Reel 3.6(N) N-3.6TRG1 GZ8 Tape & Reel 4.0(N) N-4.0TRG1 GZ9 Tape & Reel 5.0(N) N-5.0TRG1 GS5 Tape & Reel 3.3(NA) NA-3.3TRG1 GZ1 Tape & Reel 3.6(NA) NA-3.6TRG1 GAA Tape & Reel 4.0(NA) NA-4.0TRG1 GBA Tape & Reel 1.2 R-1.2TRG1 G13Q Tape & Reel 1.3 R-1.3TRG1 G17Q Tape & Reel 1.5 R-1.5TRG1 G22Q Tape & Reel 1.8 R-1.8TRG1 G27Q Tape & Reel 4

5 Ordering Information (Continued) Package Temperature Range Output oltage Part Number Marking ID Packing Type 2.5 R-2.5TRG1 G28Q Tape & Reel 2.8 R-2.8TRG1 G31Q Tape & Reel 3.0 R-3.0TRG1 G33Q Tape & Reel SOT-89 TO to 85 o C -40 to 85 o C 3.2 R-3.2TRG1 G37Q Tape & Reel 3.3 R-3.3TRG1 G41Q Tape & Reel 3.6 R-3.6TRG1 G42Q Tape & Reel 4.0 R-4.0TRG1 G43Q Tape & Reel 5.0 R-5.0TRG1 G70Q Tape & Reel 1.2 Z-1.2G1 2120Z-1.2G1 Bulk 1.2 Z-1.2TRG1 2120Z-1.2G1 Ammo 1.3 Z-1.3G1 2120Z-1.3G1 Bulk 1.3 Z-1.3TRG1 2120Z-1.3G1 Ammo 1.5 Z-1.5G1 2120Z-1.5G1 Bulk 1.5 Z-1.5TRG1 2120Z-1.5G1 Ammo 1.8 Z-1.8G1 2120Z-1.8G1 Bulk 1.8 Z-1.8TRG1 2120Z-1.8G1 Ammo 2.5 Z-2.5G1 2120Z-2.5G1 Bulk 2.5 Z-2.5TRG1 2120Z-2.5G1 Ammo 2.8 Z-2.8G1 2120Z-2.8G1 Bulk 2.8 Z-2.8TRG1 2120Z-2.8G1 Ammo 3.0 Z-3.0G1 2120Z-3.0G1 Bulk 3.0 Z-3.0TRG1 2120Z-3.0G1 Ammo 3.2 Z-3.2G1 2120Z-3.2G1 Bulk 3.2 Z-3.2TRG1 2120Z-3.2G1 Ammo 3.3 Z-3.3G1 2120Z-3.3G1 Bulk 3.3 Z-3.3TRG1 2120Z-3.3G1 Ammo 3.6 Z-3.6G1 2120Z-3.6G1 Bulk 3.6 Z-3.6TRG1 2120Z-3.6G1 Ammo 4.0 Z-4.0G1 2120Z-4.0G1 Bulk 4.0 Z-4.0TRG1 2120Z-4.0G1 Ammo 5.0 Z-5.0G1 2120Z-5.0G1 Bulk 5.0 Z-5.0TRG1 2120Z-5.0G1 Ammo BCD Semiconductor's products, as designated with "G1" suffix in the part number, are RoHS compliant and Green. 5

6 Absolute Maximum Ratings (Note 1) Parameter Symbol alue Unit Input oltage IN 6.5 Enable Input oltage CE -0.3 to IN +0.3 Output Current I OUT 300 ma Junction Temperature T J 150 o C Storage Temperature Range T STG -65 to 150 o C Lead Temperature (Soldering, 10sec) T LEAD 260 o C SOT Thermal Resistance (Note 2) θ JA SOT TO o C/W ESD (Human Body Model) ESD 2000 ESD (Machine Model) ESD 200 Note 1: Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "Recommended Operating Conditions" is not implied. Exposure to "Absolute Maximum Ratings" for extended periods may affect device reliability. Note 2: Absolute maximum ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating the device outside of its operating ratings. The maximum allowable power dissipation is a function of the maximum junction temperature, T J(max), the junction-to-ambient thermal resistance, θ JA, and the ambient temperature, T A. The maximum allowable power dissipation at any ambient temperature is calculated using: P D(max) =(T J(max) - T A )/θ JA. Exceeding the maximum allowable power dissipation will result in excessive die temperature. Recommended Operating Conditions Parameter Symbol Min Max Unit Input oltage IN 2 6 Operating Junction Temperature Range T J o C 6

7 Electrical Characteristics -1.2 Electrical Characteristics ( IN =2.2, T J =25 o C, C IN =1μF, C OUT =1μF, Bold typeface applies over -40 o C T J 85 o C, unless otherwise specified.) Parameter Symbol Conditions Min Typ Max Unit Output oltage IN =2.2 OUT 1mA I OUT 30mA Input oltage IN 6 Output Current I OUT IN - OUT =1 150 ma Load Regulation IN =2.2 RLOAD 1mA I OUT 80mA m 2.2 Line Regulation IN 6 RLINE 4 16 m I OUT =10mA Dropout oltage DROP I OUT =100mA I OUT =150mA m I OUT =200mA Quiescent Current I Q IN =2.2, I OUT =0mA μa Power Supply Rejection Ratio PSRR Ripple 0.5p-p, f=1khz IN = db Output oltage Temperature Coefficient Δ OUT /ΔT ±120 μ/ o C (Δ OUT / OUT )/ΔT ±100 ppm/ o C Short Current Limit I LIMIT OUT =0 50 ma RMS Output Noise NOISE T A =25 o C, I OUT =0 10Hz f 100kHz 15 μrms 7

8 Electrical Characteristics (Continued) -1.3 Electrical Characteristics ( IN =2.3, T J =25 o C, C IN =1μF, C OUT =1μF, Bold typeface applies over -40 o C T J 85 o C, unless otherwise specified.) Parameter Symbol Conditions Min Typ Max Unit Output oltage IN =2.3 OUT 1mA I OUT 30mA Input oltage IN 6 Output Current I OUT IN - OUT =1 150 ma Load Regulation IN =2.3 RLOAD 1mA I OUT 80mA m 2.3 Line Regulation IN 6 RLINE 4 16 m I OUT =10mA Dropout oltage DROP I OUT =100mA I OUT =150mA m I OUT =200mA Quiescent Current I Q IN =2.3, I OUT =0mA μa Power Supply Rejection Ratio PSRR Ripple 0.5p-p, f=1khz IN = db Output oltage Temperature Coefficient Δ OUT /ΔT ±130 μ/ o C (Δ OUT / OUT )/ΔT ±100 ppm/ o C Short Current Limit I LIMIT OUT =0 50 ma RMS Output Noise NOISE T A =25 o C, I OUT =0 10Hz f 100kHz 15 μrms 8

9 Electrical Characteristics (Continued) -1.5 Electrical Characteristics ( IN =2.5, T J =25 o C, C IN =1μF, C OUT =1μF, Bold typeface applies over -40 o C T J 85 o C, unless otherwise specified.) Parameter Symbol Conditions Min Typ Max Unit Output oltage IN =2.5 OUT 1mA I OUT 30mA Input oltage IN 6 Output Current I OUT IN - OUT =1 150 ma Load Regulation IN =2.5 RLOAD 1mA I OUT 80mA m 2.3 Line Regulation IN 6 RLINE 4 16 m I OUT =10mA Dropout oltage DROP I OUT =100mA I OUT =150mA m I OUT =200mA Quiescent Current I Q IN =2.5, I OUT =0mA μa Power Supply Rejection Ratio PSRR Ripple 0.5p-p, f=1khz IN = db Output oltage Temperature Coefficient Δ OUT /ΔT ±150 μ/ o C (Δ OUT / OUT )/ΔT ±100 ppm/ o C Short Current Limit I LIMIT OUT =0 50 ma RMS Output Noise NOISE T A =25 o C, I OUT =0 10Hz f 100kHz 15 μrms 9

10 Electrical Characteristics (Continued) -1.8 Electrical Characteristics ( IN =2.8, T J =25 o C, C IN =1μF, C OUT =1μF, Bold typeface applies over -40 o C T J 85 o C, unless otherwise specified.) Parameter Symbol Conditions Min Typ Max Unit Output oltage IN =2.8 OUT 1mA I OUT 30mA Input oltage IN 6 Output Current I OUT IN - OUT =1 150 ma Load Regulation IN =2.8 RLOAD 1mA I OUT 80mA m 2.3 Line Regulation IN 6 RLINE 4 16 m Dropout oltage DROP I OUT =100mA m I OUT =10mA I OUT =150mA Quiescent Current I Q IN =2.8, I OUT =0mA μa Power Supply Rejection Ratio PSRR Ripple 0.5p-p, f=1khz IN = db Output oltage Temperature Coefficient Δ OUT /ΔT ±180 μ/ o C (Δ OUT / OUT )/ΔT ±100 ppm/ o C Short Current Limit I LIMIT OUT =0 50 ma RMS Output Noise NOISE T A =25 o C 10Hz f 100kHz 30 μrms 10

11 Electrical Characteristics (Continued) -2.5 Electrical Characteristics ( IN =3.5, T J =25 o C, C IN =1μF, C OUT =1μF, Bold typeface applies over -40 o C T J 85 o C, unless otherwise specified.) Parameter Symbol Conditions Min Typ Max Unit Output oltage IN =3.5 OUT 1mA I OUT 30mA Input oltage IN 6 Output Current I OUT IN - OUT =1 150 ma Load Regulation IN =3.5 RLOAD 1mA I OUT 80mA m 3 Line Regulation IN 6 RLINE 4 16 m Dropout oltage DROP I OUT =100mA m I OUT =10mA I OUT =150mA Quiescent Current I Q IN =3.5, I OUT =0mA μa Power Supply Rejection Ratio PSRR Ripple 0.5p-p, f=1khz IN = db Output oltage Temperature Coefficient Δ OUT /ΔT ±250 μ/ o C (Δ OUT / OUT )/ΔT ±100 ppm/ o C Short Current Limit I LIMIT OUT =0 50 ma RMS Output Noise NOISE T A =25 o C 10Hz f 100kHz 30 μrms 11

12 Electrical Characteristics (Continued) -2.8 Electrical Characteristics ( IN =3.8, T J =25 o C, C IN =1μF, C OUT =1μF, Bold typeface applies over -40 o C T J 85 o C, unless otherwise specified.) Parameter Symbol Conditions Min Typ Max Unit Output oltage IN =3.8 OUT 1mA I OUT 30mA Input oltage IN 6 Output Current I OUT IN - OUT =1 150 ma Load Regulation IN =3.8 RLOAD 1mA I OUT 80mA m 3.3 Line Regulation IN 6 RLINE 4 16 m Dropout oltage DROP I OUT =100mA m I OUT =10mA I OUT =150mA Quiescent Current I Q IN =3.8, I OUT =0mA μa Power Supply Rejection Ratio PSRR Ripple 0.5p-p, f=1khz IN = db Output oltage Temperature Coefficient Δ OUT /ΔT ±280 μ/ o C (Δ OUT / OUT )/ΔT ±100 ppm/ o C Short Current Limit I LIMIT OUT =0 50 ma RMS Output Noise NOISE T A =25 o C 10Hz f 100kHz 30 μrms 12

13 Electrical Characteristics (Continued) -3.0 Electrical Characteristics ( IN =4, T J =25 o C, C IN =1μF, C OUT =1μF, Bold typeface applies over -40 o C T J 85 o C, unless otherwise specified.) Parameter Symbol Conditions Min Typ Max Unit Output oltage IN =4 OUT mA I OUT 30mA Input oltage IN 6 Output Current I OUT IN - OUT =1 150 ma Load Regulation IN =4 RLOAD m 1mA I OUT 80mA Line Regulation RLINE 3.5 IN m Dropout oltage DROP I OUT =100mA I OUT =10mA I OUT =150mA m Quiescent Current I Q IN =4, I OUT =0mA μa Power Supply Rejection Ratio PSRR Ripple 0.5p-p, f=1khz IN =4 65 db Output oltage Temperature Coefficient Δ OUT /ΔT ±300 μ/ o C (Δ OUT / OUT )/ΔT ±100 ppm/ o C Short Current Limit I LIMIT OUT =0 50 ma RMS Output Noise NOISE T A =25 o C 10Hz f 100kHz 30 μrms 13

14 Electrical Characteristics (Continued) -3.2 Electrical Characteristics ( IN =4.2, T J =25 o C, C IN =1μF, C OUT =1μF, Bold typeface applies over -40 o C T J 85 o C, unless otherwise specified.) Parameter Symbol Conditions Min Typ Max Unit Output oltage IN =4.2 OUT 1mA I OUT 30mA Input oltage IN 6 Output Current I OUT IN - OUT =1 150 ma Load Regulation IN =4.2 RLOAD 1mA I OUT 80mA m 3.7 Line Regulation IN 6 RLINE 4 16 m Dropout oltage DROP I OUT =100mA m I OUT =10mA I OUT =150mA Quiescent Current I Q IN =4.2, I OUT =0mA μa Power Supply Rejection Ratio PSRR Ripple 0.5p-p, f=1khz IN = db Output oltage Temperature Coefficient Δ OUT /ΔT ±320 μ/ o C (Δ OUT / OUT )/ΔT ±100 ppm/ o C Short Current Limit I LIMIT OUT =0 50 ma RMS Output Noise NOISE T A =25 o C 10Hz f 100kHz 30 μrms 14

15 Electrical Characteristics (Continued) -3.3 Electrical Characteristics ( IN =4.3, T J =25 o C, C IN =1μF, C OUT =1μF, Bold typeface applies over -40 o C T J 85 o C, unless otherwise specified.) Parameter Symbol Conditions Min Typ Max Unit Output oltage IN =4.3 OUT 1mA I OUT 30mA Input oltage IN 6 Output Current I OUT IN - OUT =1 150 ma Load Regulation IN =4.3 RLOAD 1mA I OUT 80mA m 3.8 Line Regulation IN 6 RLINE 4 16 m Dropout oltage DROP I OUT =100mA m I OUT =10mA I OUT =150mA Quiescent Current I Q IN =4.3, I OUT =0mA μa Power Supply Rejection Ratio PSRR Ripple 0.5p-p, f=1khz IN = db Output oltage Temperature Coefficient Δ OUT /ΔT ±330 μ/ o C (Δ OUT / OUT )/ΔT ±100 ppm/ o C Short Current Limit I LIMIT OUT =0 50 ma RMS Output Noise NOISE T A =25 o C 10Hz f 100kHz 30 μrms 15

16 Electrical Characteristics (Continued) -3.6 Electrical Characteristics ( IN =4.6, T J =25 o C, C IN =1μF, C OUT =1μF, Bold typeface applies over -40 o C T J 85 o C, unless otherwise specified.) Parameter Symbol Conditions Min Typ Max Unit Output oltage IN =4.6 OUT 1mA I OUT 30mA Input oltage IN 6 Output Current I OUT IN - OUT =1 150 ma Load Regulation IN =4.6 RLOAD 1mA I OUT 80mA m 4.6 Line Regulation IN 6 RLINE 4 16 m Dropout oltage DROP I OUT =100mA m I OUT =10mA I OUT =150mA Quiescent Current I Q IN =4.6, I OUT =0mA μa Power Supply Rejection Ratio PSRR Ripple 0.5p-p, f=1khz IN = db Output oltage Temperature Coefficient Δ OUT /ΔT ±330 μ/ o C (Δ OUT / OUT )/ΔT ±100 ppm/ o C Short Current Limit I LIMIT OUT =0 50 ma RMS Output Noise NOISE T A =25 o C 10Hz f 100kHz 30 μrms 16

17 Electrical Characteristics (Continued) -4.0 Electrical Characteristics ( IN =5.0, T J =25 o C, C IN =1μF, C OUT =1μF, Bold typeface applies over -40 o C T J 85 o C, unless otherwise specified.) Parameter Symbol Conditions Min Typ Max Unit Output oltage IN =5.0 OUT 1mA I OUT 30mA Input oltage IN 6 Output Current I OUT IN - OUT =1 150 ma Load Regulation IN =5.0 RLOAD 1mA I OUT 80mA m 5 Line Regulation IN 6 RLINE 4 16 m Dropout oltage DROP I OUT =100mA m I OUT =10mA I OUT =150mA Quiescent Current I Q IN =5.0, I OUT =0mA μa Power Supply Rejection Ratio PSRR Ripple 0.5p-p, f=1khz IN = db Output oltage Temperature Coefficient Δ OUT /ΔT ±330 μ/ o C (Δ OUT / OUT )/ΔT ±100 ppm/ o C Short Current Limit I LIMIT OUT =0 50 ma RMS Output Noise NOISE T A =25 o C 10Hz f 100kHz 30 μrms 17

18 Electrical Characteristics (Continued) -5.0 Electrical Characteristics ( IN =6.0, T J =25 o C, C IN =1μF, C OUT =1μF, Bold typeface applies over -40 o C T J 85 o C, unless otherwise specified.) Parameter Symbol Conditions Min Typ Max Unit Output oltage IN =6.0 OUT 1mA I OUT 30mA Input oltage IN 6 Output Current I OUT IN - OUT =1 150 ma Load Regulation IN =4.3 RLOAD 1mA I OUT 80mA m 5.5 Line Regulation IN 6 RLINE 4 16 m Dropout oltage DROP I OUT =100mA m I OUT =10mA I OUT =150mA Quiescent Current I Q IN =6.0, I OUT =0mA μa Power Supply Rejection Ratio PSRR Ripple 0.5p-p, f=1khz IN = db Output oltage Temperature Coefficient Δ OUT /ΔT ±330 μ/ o C (Δ OUT / OUT )/ΔT ±100 ppm/ o C Short Current Limit I LIMIT OUT =0 50 ma RMS Output Noise NOISE T A =25 o C 10Hz f 100kHz 30 μrms 18

19 Typical Performance Characteristics Output oltage () IN = Output Current (A) -2.5 T C =-40 o C T C =25 o C T C =85 o C Output oltage () I OUT =10mA IN =3.5 I OUT =50mA I OUT =100mA I OUT =150mA Case Temperature ( o C) Figure 4. Output oltage vs. Output Current Figure 5. Output oltage vs. Case Temperature Quiescent Current (μa) Input oltage () -2.5 T C =-40 o C I OUT =0 T C =25 o C T C =85 o C Quiescent Current (μa) T C =-40 o C IN =3.5 T C =25 o C T C =85 o C Output Current (A) Figure 6. Quiescent Current vs. Input oltage Figure 7. Quiescent Current vs. Output Current 19

20 Typical Performance Characteristics (Continued) Quiescent Current (μa) IN =3.5 I OUT =0 Dropout oltage () T C =-40 o C T C =25 o C T C =85 o C Case Temperature ( o C) Output Current (A) Figure 8. Quiescent Current vs. Case Temperature Figure 9. Dropout oltage vs. Output Current 450 Dropout oltage () I OUT =10mA I OUT =80mA I OUT =150mA OUT (50m/Div) I OUT (50mA/Div) Case Temperature ( o C) Figure 10. Dropout oltage vs. Case Temperature Figure 11. Load Transient (I OUT =0 to 150mA) 20

21 Typical Performance Characteristics (Continued) OUT (50m/Div) IN (1/Div) I OUT =150mA I OUT =10mA -2.5 Figure 12. Line Transient (Condition: IN =2.5 to 3.5,I OUT =10mA) Figure 13. PSRR vs. Frequency Input oltage -2.5 IN (0.5/Div) Output oltage OUT (0.5/Div) 0 Figure 14. Start-up 21

22 Typical Application IN= OUT=2.5 IN IN OUT OUT GND C OUT 1μF C IN 1μF Note: Filter capacitors are required at the 's input and output. 1μF capacitor is required at the input. The minimum output capacitance required for stability should be more than 1μF with ESR from 0.01Ω to 100Ω. Ceramic capacitors are recommended. Figure 15. Typical Application of 22

23 Mechanical Dimensions SOT-23 Unit: mm(inch) 0.500(0.020) 0.700(0.028) R0.100(0.004) 0.900(0.035) 1.100(0.043) 0.100(0.004) GAUGE PLANE 7.0 R0.100(0.004) (0.041)REF 2.800(0.110) 3.000(0.118) 0.010(0.0004) 0.100(0.004) 0.0 ~ (0.008)MIN 0.550(0.022)REF (0.003) 0.180(0.007) 2.300(0.091) 2.500(0.098) 1.200(0.047) 1.400(0.055) 0.890(0.035) 1.030(0.041) 1.900(0.075)REF 0.300(0.012) 0.510(0.020) 23

24 Mechanical Dimensions (Continued) SOT-89 Unit: mm(inch) 1.550(0.061)REF 4.400(0.173) 4.600(0.181) 1.030(0.041)REF 1.400(0.055) 1.600(0.063) (0.156) 4.250(0.167) 2.300(0.091) 2.600(0.102) 2.060(0.081)REF 0.900(0.035) 1.100(0.043) 0.320(0.013) 0.520(0.020) 3.000(0.118) TYP 0.320(0.013) 0.520(0.020) 0.480(0.019) (0.014) 0.450(0.018) (0.059) 1.800(0.071) 0.320(0.013)REF (0.087)REF 1.620(0.064)REF R0.150(0.006) 10 24

25 Mechanical Dimensions (Continued) TO-92 (Bulk Packing) Unit: mm(inch) 1.000(0.039) 1.400(0.055) 3.430(0.135) MIN 3.300(0.130) 3.700(0.146) 0.000(0.000) 0.380(0.015) Φ1.600(0.063) MAX 4.400(0.173) 4.800(0.189) 0.360(0. 014) 0.760(0.030) (0.492) (0.610) 0.320(0.013) 0.510(0.020) 4.300(0.169) 4.700(0.185) 1.270(0.050) TYP 2.420(0. 095) 2.660(0.105) 25

26 Mechanical Dimensions (Continued) TO-92 (Ammo Packing) Unit: mm(inch) 4.400(0.173) 4.800(0.189) (0.043) (0.055) 3.430(0.135) MIN 4.300(0.169) 4.700(0.185) 1.270(0.050) Typ 3.300(0.130) 3.800(0.150) 0.320(0.013) (0.020) 2.500(0.098) 4.000(0.157) 0.000(0.000) 0.380(0.015) Φ1.600(0.063) MAX (0.492) (0.571) (0. 512) (0.591) (0.015) 0.550(0.022 ) 2.540(0.100) Typ 26

27 IMPORTANT NOTICE reserves the right to make changes without further notice to any products or specifications herein. does not assume any responsibility for use of any its products for any IMPORTANT NOTICE particular purpose, nor does assume any liability arising out of the application or use of any its products or circuits. does not convey any license under its patent rights or reserves the right to make changes without further notice to any products or specifications herein. does not assume any responsibility for use of any its products for any particular purpose, nor does assume any liability arising out of the application or use other rights nor the rights of others. MAIN SITE - of Headquarters any its products or circuits. BCD Semiconductor Manufacturing - Wafer Limited Fab does not convey any license under its patent rights or BCD other (Shanghai) rights Micro-electronics nor the rights Limited of others. Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd. No. 1600, Zi Xing Road, Shanghai ZiZhu Science-based Industrial Park, , P. R.C. 800 Yishan Road, Shanghai , China Tel: , Fax: Tel: , Fax: MAIN SITE BCD REGIONAL - Headquarters Semiconductor SALES Manufacturing OFFICE Limited - Wafer BCD FabSemiconductor Manufacturing Limited Shenzhen BCD - Wafer Semiconductor Fab Office Manufacturing Limited Taiwan Shanghai Office - IC Design SIM-BCD (Taipei) Group Semiconductor Manufacturing Co., Ltd. Shanghai No. 1600, Zi SIM-BCD Xing Road, Semiconductor Shanghai ZiZhu Manufacturing Science-based Co., Limited Industrial Ltd., Shenzhen Park, , Office China BCD 800 Semiconductor Yi Advanced Shan Road, Analog (Taiwan) Shanghai Circuits Company , (Shanghai) China Limited Corporation Unit Tel: 800, , A Yi Room Shan Road, 1203,Skyworth Shanghai Fax: Bldg., , Gaoxin ChinaAve.1.S., Nanshan District 3F, No.17, Tel: F, Lane Zone 171, B, 900, Sec. 1491, 2, Yi Fax: Jiu-Zong Shan Road, Rd., Shanghai Nei-Hu 0008Dist., , Taipei(114), China Taiwan, R.O.C Shenzhen Tel: , 1491, China Fax: Tel: Tel: , Fax: Tel: REGIONAL , SALES OFFICE Fax: Fax: / REGIONAL Shenzhen OfficeSALES OFFICE Taiwan Office USA Office Taiwan Shenzhen Shanghai Office SIM-BCD Office (Hsinchu) Semiconductor Manufacturing Co., Ltd., Shenzhen Office BCD Shanghai Unit A Semiconductor Room SIM-BCD 1203, Skyworth Semiconductor (Taiwan) Bldg., Company Gaoxin Manufacturing Limited Ave.1.S., Nanshan Co., Ltd. District, Shenzhen Shenzhen, Office 8F, Advanced China No.176, Analog Sec. 2, Gong-Dao Circuits (Shanghai) 5th Road, Corporation East District Shenzhen Office USA BCD Office Taiwan Semiconductor Office (Taiwan) Company Limited Korea OfficeUSA BCD Office Semiconductor Corp. BCD 4F, Semiconductor 298-1, BCD Rui Semiconductor Guang Corp. Road, (Taiwan) Nei-Hu District, Company Taipei, BCD Limited Semiconductor BCD Semiconductor Huntwood Limited Korea Ave. Corporation Hayward, office Taiwan Kato 4F, Road, 298-1, Fremont, Rui Guang CA Road, 94538, Nei-Hu USA District, Room Taipei, , CA Digital-Empire 94544, Huntwood USA Ave. II, 486 Hayward, Sin-dong, HsinChu Room Tel: E, City 5F, Noble 300, Taiwan, 7951 Center, No.1006, R.O.C 3rd Fuzhong Road, Futian District, Shenzhen , China Tel: Tel: Taiwan 2808 Yeongtong-Gu, CA Tel Suwon-city, : 94544, U.S.A Gyeonggi-do, Korea Tel: Fax: , Fax: Fax: Fax: Fax: Tel: Fax: Tel: Tel Fax: : Fax: