STGB10NC60KD, STGD10NC60KD STGF10NC60KD, STGP10NC60KD

Size: px

Start display at page:

Download "STGB10NC60KD, STGD10NC60KD STGF10NC60KD, STGP10NC60KD"

Reginald Hampton
6 years ago
Views:

1 STGB10NC60KD, STGD10NC60KD STGF10NC60KD, STGP10NC60KD 10 A, 600 V shortcircuit rugged IGBT Features Lower on voltage drop (V CE(sat) ) Lower C RES / C IES ratio (no crossconduction susceptibility) Very soft ultra fast recovery antiparallel diode Shortcircuit withstand time 10µs Description TAB 1 TAB D 2 PAK TAB DPAK This IGBT utilizes the advanced PowerMESH process resulting in an excellent tradeoff between switching performance and low otate behavior. TO220FP TO Applicatio High frequency motor controls SMPS and PFC in both hard switch and resonant topologies Motor drives Figure 1. Internal schematic diagram Table 1. Device summary Order codes Marking Packages Packaging STGB10NC60KDT4 GB10NC60KD D 2 PAK STGD10NC60KDT4 GD10NC60KD DPAK STGF10NC60KD GF10NC60KD TO220FP STGP10NC60KD GP10NC60KD TO220 Tape and reel Tube November 2009 Doc ID Rev 6 1/

2 Contents STGx10NC60KD Contents 1 Electrical ratings Electrical characteristics Electrical characteristics (curves) Test circuits Package mechanical data Packaging mechanical data Revision history /20 Doc ID Rev 6

3 STGx10NC60KD Electrical ratings 1 Electrical ratings Table 2. Absolute maximum ratings Value Symbol Parameter D²PAK TO220 DPAK TO220FP Unit V CES Collectoremitter voltage (V GE = 0) 600 V (1) I C Continuous collector current at T C = 25 C 20 9 A I (1) C Continuous collector current at T C = 100 C 10 6 A I (2) CL Turnoff latching current 30 A I (3) CP Pulsed collector current 30 A V GE Gateemitter voltage ±20 V I F Diode RMS forward current at Tc=25 C 10 A I FSM Surge non repetitive forward current T p = 10 ms sinusoidal 20 A P TOT Total dissipation at T C = 25 C W V ISO t scw T stg T j Iulation withstand voltage (RMS) from all three leads to external heat sink (t=1s;t C =25 C) Shortcircuit withstand time V CE = 0.5 V CES, T j = 125 C, R G = 10 Ω, V GE = 12 V Storage temperature Operating junction temperature 2500 V 10 µs 55 to 150 C 1. Calculated according to the iterative formula I C ( T C ) T jmax ( ) T C R thj c V CE( sat) ( max) T jmax = ( ( ), I C ( T C )) 2. Vclamp = 80 % V CES, V GE = 15 V, R G = 10 Ω, T J = 150 C 3. Pulse width limited by maximum junction temperature and turnoff within RBSOA Doc ID Rev 6 3/20

4 Electrical ratings STGx10NC60KD Table 3. Thermal data Value Symbol Parameter TO220 D²PAK DPAK TO220FP Unit R thjcase Thermal resistance junctioncase IGBT R thjcase Thermal resistance junctioncase diode C/W R thjamb Thermal resistance junctionambient /20 Doc ID Rev 6

5 STGx10NC60KD Electrical characteristics 2 Electrical characteristics (T j =25 C unless otherwise specified) Table 4. Static Symbol Parameter Test conditio Min. Typ. Max. Unit V (BR)CES Collectoremitter breakdown voltage (V GE = 0) I C = 1mA 600 V V CE(sat) Collectoremitter saturation voltage V GE = 15V, I C = 5A V GE = 15V, I C = 5A, T j = 125 C V V V GE(th) Gate threshold voltage V CE = V GE, I C = 250µA V I CES Collector cutoff current (V GE = 0) V CE = 600 V V CE =600 V, T j = 125 C µa ma I GES Gateemitter leakage current (V CE = 0) V GE = ±20V ±100 na g fs (1) Forward traconductance V CE = 15V, I C = 5A 15 S 1. Pulse test: pulse duration < 300 µs, duty cycle < 2 % Table 5. Dynamic Symbol Parameter Test conditio Min. Typ. Max. Unit C ies C oes C res Input capacitance Output capacitance Reverse trafer capacitance V CE = 25V, f = 1MHz, V GE = pf pf pf Q g Q ge Q gc Total gate charge Gateemitter charge Gatecollector charge V CE = 390V, I C = 5A, V GE = 15V, (see Figure 19) nc nc nc Doc ID Rev 6 5/20

6 Electrical characteristics STGx10NC60KD Table 6. Switching on/off (inductive load) Symbol Parameter Test conditio Min. Typ. Max. Unit t d(on) t r (di/dt) on Turnon delay time Current rise time Turnon current slope V CC = 390V, I C = 5A R G = 10Ω, V GE = 15V (see Figure 20) A/µs t d(on) t r (di/dt) on Turnon delay time Current rise time Turnon current slope V CC = 390V, I C = 5A R G = 10Ω, V GE = 15V, T j =125 C (see Figure 20) A/µs t r (V off ) t d ( off ) t f Off voltage rise time Turnoff delay time Current fall time V cc = 390V, I C = 5A, R GE = 10Ω, V GE = 15V (see Figure 20) t r (V off ) t d ( off ) t f Off voltage rise time Turnoff delay time Current fall time V cc = 390V, I C = 5A, R GE =10Ω, V GE =15V, T j =125 C (see Figure 20) Table 7. Switching energy (inductive load) Symbol Parameter Test conditio Min. Typ. Max. Unit E (1) on (2) E off E ts Turnon switching losses Turnoff switching losses Total switching losses V CC = 390V, I C = 5A R G =10Ω, V GE =15V (see Figure 20) µj µj µj E (1) on E (2) off E ts Turnon switching losses Turnoff switching losses Total switching losses V CC = 390V, I C = 5A R G =10Ω, V GE = 15V, T j = 125 C (see Figure 20) µj µj µj 1. Eon is the tunon losses when a typical diode is used in the test circuit in figure 2. If the IGBT is offered in a package with a copak diode, the copack diode is used as external diode. IGBTs & Diode are at the same temperature (25 C and 125 C) 2. Turnoff losses include also the tail of the collector current 6/20 Doc ID Rev 6

7 STGx10NC60KD Electrical characteristics Table 8. Collectoremitter diode Symbol Parameter Test conditio Min Typ. Max. Unit V F Forward onvoltage I F =5 A I F =5 A, T j =125 C V V t rr Q rr I rrm Reverse recovery time Reverse recovery charge Reverse recovery current I F =5 A, V R =40 V, di/dt=100 A/µs (see Figure 5) nc A t rr Q rr I rrm Reverse recovery time Reverse recovery charge Reverse recovery current I F =5 A, V R =40 V, T j =125 C, di/dt=100 A/µs (see Figure 5) nc A Doc ID Rev 6 7/20

8 Electrical characteristics STGx10NC60KD 2.1 Electrical characteristics (curves) Figure 2. Output characteristics Figure 3. Trafer characteristics Figure 4. Traconductance Figure 5. Collectoremitter on voltage vs temperature Figure 6. Gate charge vs gatesource voltage Figure 7. Capacitance variatio 8/20 Doc ID Rev 6

9 STGx10NC60KD Electrical characteristics Figure 8. Normalized gate threshold voltage vs temperature Figure 9. Collectoremitter on voltage vs collector current Figure 10. Normalized breakdown voltage vs temperature Figure 11. Switching losses vs temperature Figure 12. Switching losses vs gate resistance Figure 13. Switching losses vs collector current Doc ID Rev 6 9/20

10 Electrical characteristics STGx10NC60KD Figure 14. Thermal impedance for D²PAK, DPAK and TO220 Figure 15. Turnoff SOA Figure 16. Emittercollector diode characteristics Figure 17. Thermal impedance for TO220FP 10/20 Doc ID Rev 6

11 STGx10NC60KD Test circuits 3 Test circuits Figure 18. Test circuit for inductive load switching Figure 19. Gate charge test circuit Figure 20. Switching waveform Figure 21. Diode recovery time waveform Doc ID Rev 6 11/20

12 Package mechanical data STGx10NC60KD 4 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specificatio, grade definitio and product status are available at: ECOPACK is an ST trademark. 12/20 Doc ID Rev 6

13 STGx10NC60KD Package mechanical data Table 9. Dim. D 2 PAK package mechanical data mm inch Min. Typ. Max. Min. Typ. Max. A A b b c c D D E E e e H J L L L R V Figure 22. D 2 PAK package drawing _M Doc ID Rev 6 13/20

14 Package mechanical data STGx10NC60KD Table 10. Dim. DPAK package mechanical data mm Min. Typ Max. A A A b b c c D D E E e 2.28 e H L 1 L L L R 0.20 V2 0 o 8 o Figure 23. DPAK package drawing _G 14/20 Doc ID Rev 6

15 STGx10NC60KD Package mechanical data Table 11. Dim. TO220FP package mechanical data mm Min. Typ. Max. A B D E F F F G G H L2 16 L L L L L Dia Figure 24. TO220FP package drawing L7 E A B Dia L6 L5 D F1 F2 F H G1 G L2 L4 L _Rev_K Doc ID Rev 6 15/20

16 Package mechanical data STGx10NC60KD Table 12. TO220 type A mechanical data mm Dim. Min. Typ. Max. A b b c D D E e e F H J L L L L P Q Figure 25. TO220 type A package drawing _S 16/20 Doc ID Rev 6

17 STGx10NC60KD Packaging mechanical data 5 Packaging mechanical data D 2 PAK FOOTPRINT TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm inch MIN. MAX. MIN. MAX. A B C D G N T TAPE MECHANICAL DATA DIM. mm inch MIN. MAX. MIN. MAX. A B D D E F K P P P R T W BASE QTY BULK QTY Doc ID Rev 6 17/20

18 Packaging mechanical data STGx10NC60KD DPAK FOOTPRINT All dimeio are in millimeters TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm inch MIN. MAX. MIN. MAX. A B C D G N T TAPE MECHANICAL DATA DIM. mm inch MIN. MAX. MIN. MAX. A B B D D E F K P P P R W BASE QTY BULK QTY /20 Doc ID Rev 6

19 STGx10NC60KD Revision history 6 Revision history Table 13. Document revision history Date Revision Changes 14Jun New release. 19Jul Complete version. 27Jan Ierted ecopack indication. 01Mar The document has been reformatted. 08Feb Modified value on Table 6.: Switching on/off (inductive load). 24Nov Ierted DPAK package option. Doc ID Rev 6 19/20

20 STGx10NC60KD Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ( ST ) reserve the right to make changes, correctio, modificatio or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST s terms and conditio of sale. Purchasers are solely respoible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No licee, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a licee grant by ST for the use of such third party products or services, or any intellectual property contained therein or coidered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER S OWN RISK. Resale of ST products with provisio different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners STMicroelectronics All rights reserved STMicroelectronics group of companies Australia Belgium Brazil Canada China Czech Republic Finland France Germany Hong Kong India Israel Italy Japan Malaysia Malta Morocco Philippines Singapore Spain Sweden Switzerland United Kingdom United States of America 20/20 Doc ID Rev 6

21 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: STMicroelectronics: STGP10NC60KD STGF10NC60KD STGB10NC60KDT4 STGD10NC60KDT4

STGB14NC60KD STGF14NC60KD, STGP14NC60KD

STGB14NC60KD STGF14NC60KD, STGP14NC60KD 14 A, 600 V shortcircuit rugged IGBT Features Short circuit withstand time 10µs. TAB 2 TAB Low onvoltage drop (V CE(sat) ) Low C res / C ies ratio (no cross conduction