TECHNICAL DATA DOORS

Transcription

1 TECHNICA DATA DOORS GENERA ENGINEERING DETAIS for DOOR EDGE and MEETING STIES Note: Edge designs, shown as pairs of doors may in some cases be used in single door applications. Dimensions shown are standard for the application. Variations to suit the design conditions are available. SQUARE EDGE* VEE (OPPOSING) BEVES *Square edge configuration used on standard door products unless otherwise precluded by other requirements. Standard bevel is 1/8 in 2 PARAE BEVES Standard bevel is 1/8 in 2 RABBETED (OFFSET)** RABBETED (EQUA)** **May also be bevelled RADIUS (BU NOSE) 2 5/16 Radius 3/16 TYPICA PREPARATION FOR SEMI - MORTISED WEATHERSTRIPPING. TYPICA PREPARATION FOR FUY MORTISED WEATHERSTRIPPING. Weatherstripping Furnished and applied by others. Weatherstripping Furnished and applied by others. DOORS - GENERA

2 TECHNICA DATA DOORS GENERA ENGINEERING DETAIS for Standard TOP and BOTTOM CHANNE - 16 GA. TOP AND BOTTOM CHANNES -16 GA. SPOTWED 3 O.C. ¾ TYP HANGING HOES FOR PAINT CONVEYOR FIXTURE DOORS - GENERA

3 TECHNICA DATA DOORS GENERA ENGINEERING DETAIS for TOP and BOTTOM COSING CHANNE EXTRUDED VINY COSING CHANNE Not for use on Doors DOOR TOP CHANNE16 gage DOOR SKIN STEE COSING CHANNE PRE TENSIONED EG HODS CHANNE FIRMY AGAINST SIDES OF DOOR TOP CHANNE AND PROVIDES SIGHT CROWN. #20 GA. MIN. COSING CHANNE HED WITH TWO #6 x 1 ¼ SMS (#4 HEAD) DOOR TOP (OR BOTTOM) CHANNE 16 gage DOOR SKIN WITH DOOR SIZE FUSH TOP 20 GA. COSING PATE SPOTWEDED TO COSING CHANNE 20 GA. MIN. COSING CHANNE INSTAED FUSH WITH TWO #6 x 1 ¼ FATHEAD SCREWS ATERNATE STEE COSING CHANNE DESIGNED FOR USE IN OCKSEAM DOOR CONSTRUCTION DOOR TOP (OR BOTTOM) CHANNE 16 gage DOOR SKIN NOTCH FOR OCKSEAM DOORS - GENERA

4 TECHNICA DATA DOORS DETAI ENGINEERING DETAIS for MONORAI CUTOUT STANDARD MONORAI CUTOUT EDGE OF CUTOUT FINISHED SEAMESS ONY WHEN SPECIFIED GA. RETAINER Note: Gasket material supplied by pioneer, only when required, as an untrimmed piece of ¼ neoprene. Fitting, cutting, trimming and installation of the gasket by others. Retainer, screws and neoprene shipped loose. #6 x 1 SMS ¼ NEOPRENE GASKET Dimensions and sizes shown are standard for this feature. Variations to suite designed conditions are available. OPTIONA GASKETTED CUT OUT DOORS - GENERA

5 OCKSTIE OCKSTIE TECHNICA DATA DOORS GENERA 10 EEVATIONS 4 CEAR WIDTH CEAR HEIGHT V FINISH FOOR NV FINISH FOOR G FINISH FOOR M M 6 EQUA EQUA EQUA EQUA EQUA CEAR HEIGHT G4 (Add single vertical bar) FINISH FOOR G3 FINISH FOOR G6 (Add single vertical bar) G9 (Add two vertical bars) NG FINISH FOOR CEAR WIDTH NOTE: 12 x 12 ouver standard for 2 0 & 2-4 door all others 20 x 12, 20 x 24 ouver available TOP EAF CEAR HEIGHT K 3/16 N /16 12 FG 9-3/ /8 FINISH FOOR D (DUTCH) DOORS - GENERA

6 TECHNICA DATA GENERA DOOR HANDING ENGINEERING DETAIS for HANDING When viewed from the exterior side of the door, the hinge edge of the door determines the hand. When the hinge edge is at the left, the swing is left hand, if the door swings away from the viewer; left hand reverse if it swings toward the viewer. When the hinge edge is at the right, the swing is right hand if the door swings away from the viewer; right hand reverse if it swings toward the viewer. EFT HAND (.H.) RIGHT HAND (R.H.) EFT HAND REVERSE BEVE (.H.R.B) RIGHT HAND REVERSE BEVE (R.H.R.B) EFT HAND ACTIVE (.H.) PAIR RIGHT HAND ACTIVE (R.H.) PAIR EFT HAND REVERSE BEVE ACTIVE (.H.R.B) PAIR RIGHT HAND REVERSE BEVE ACTIVE (R.H.R.B) PAIR DOUBE ACTING DOUBE ACTING PAIR EFT HAND DOUBE EGRESS PAIR RIGHT HAND DOUBE EGRESS PAIR DOORS - GENERA