CURRIES Tech Data Frame Section. Revised Oct., 2018

Transcription

1 CURRIES Tech Data Frame Section Revised Oct., 2018

2 i Index August, 2017 DESCRIPTION PAGE(S) Anchors Drywall Frame Base Anchor...35 Compression Anchor...34, 36, 39 Multipurpose Anchor Installation...17 Steel Channel Anchor Installation Security Anchor...34 Anchors Flush Frame (Masonry) Ceiling Strut...18 Conduit Compatible Electric Steel Channel...14 Existing Wall Anchors...9, 11, 12 Floor Anchor (Foot Clip) oose Spline Masonry Anchors Mullion Stirrup Anchor...18 Multipurpose Anchor...16 Steel Channel Anchor Steel Channel Anchor Installation Wire Truss Anchor...15 Wood Stud Anchor...15 Borrowed ite Frames Cabinet Jamb Frames...90 CCW Stick ength Components Communicating Frames/Mullion...96 Curriseal Frames Custom Frame Profiles Double Egress Frames...2, 107 Drywall Frames Corner Detail Installation...40 Profiles Throat Filler...43 KD Frame Assembly Instructions Electroynx System Fabricaton Frame Corner Details Cutting and Notching Field Splice...24 Welded Corner Details Flush Masonry Frames Corner Details Profiles...3-5

3 ii Index October, 2018 DESCRIPTION PAGE(S) Grout Hole...85 Hardware ocations Preparations Automatic Flush Bolts...87 Closer Preparations Coordinator Preparations...84 Deadlock Strike Preparations...67 Electric Strike Preparations...74, 88, 89 ock Exit Device Preparations Rim Exit...73 Vertical Rod Exit...72 Flush Bolt Preparations Hinge Preparations 4-1/ Anchor Hinge Preparation...58 Continuous Hinge Preparation...55 Electric Hinges...52, 57 Double Acting Hinges...59 Full width Hinge Reinforcement...54 High Frequency Hinge Reinforcement...53 Pocket Pivot Preparation...60 Security Hinge...56 Mullion (Hardware Removable)...83 Pivots...63, 64 Strikes...61, 65, 66, 70 Surface Bolt Preparation...83 Hospital Stops KD Frame Assembly Instructions KD Sideight Frame ead ined Frame Steel Channel...19 Mullion Construction Removable Mullion Vertical / Horzontal Pocket Door Frame Rabbet Dimensions...49 Rescue Hardware...62 Rough Buck Frames...91 Security Sidelite Frames Silencers Slip-on Drywall Frames Slip-on Hybrid Drywall Frames Spats...99 Stainless Steel Frames...25, 26 Mercury Thermal Break Frame...123, 124 Mercury Thermal Break Frame with Stucco Flange Thermal Break Frames Transom Frame Removable Panel Installation Wall construction Details Masonry...8

4 1 Flush Masonry KD Miter Corner Joint March, 2015 BEND TABS TOWARD WA #8 SCREW (MS002485) (REQUIRED ON A FIRE RATED KD FRAMES) HEAD CORNER ASSEMBY 2 (50.8) HEAD JAMB HEAD SPOT WEDS 2-7/16 (61.9) BREAK AWAY CORNER CIP 1-13/16 (46) JAMB USING THE BREAK-OFF TOO, BEND CIP BACK AND FORTH TOWARD OPPOSITE FACE OF FRAME. DO NOT BEND PAST THE OUTSIDE FACE TO AVOID DEFORMING THE FACE. BREAK OFF TOO JAMB NOTE: USING PIERS TO BREAK OFF THE CORNER CIP MAY RESUT IN DAMAGE TO THE FACE OF FRAME

5 2 Masonry KD 4 Face Head March, 2015 #8 SCREW (REQUIRED ON A FIRE RATED KD FRAMES) HEAD FIER CORNER CIP BEND TABS TOWARD WA Masonry KD Double Egress Frame #8 SCREW (REQUIRED ON A FIRE RATED KD FRAMES) 1/2 * (12.7) 4-3/4-14 (120.6) - (355.6) 1-3/8 (34.9) JAMB DEM 2-5/8 (66.7) BEND TABS TOWARD WA 1/2 * (12.7) 2 (50.8) 4-3/4-14 (120.6) - (355.6) HEAD GE 2-5/8 (66.7) * 5-3/4 (146.1) JAMB DEPTH HAS 7/16 (11.1) RETURN

6 3 Masonry KD G Profile - Corner Details March, 2015 #8 SCREW (REQUIRED ON A FIRE RATED KD FRAMES) BEND TABS TOWARD WA JAMB HEAD CORNER ASSEMBY Masonry KD 2 Face Flush Frame Unequal Rabbet 1-15/16 (49.2) VARIES 1-9/16 (39.7) 5/8 (15.9) 2 (50.8) M 1/2 (12.7) KD M TYPE FUSH GAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9) VARIABE SOFFIT JAMB DEPTH 4-1/2 (114.3) THRU 14 (355.6) (1/8 (3.2) INCREMENTS) AVAIABE WITH 4 (101.6) FACE HEADS NOTE: 5-3/4 (146.1) JAMB DEPTH STANDARD WITH 7/16 (11.1) RETURNS TO PROVIDE 4-7/8 (123.8) THROAT OPENING

7 4 Masonry 1", 1-1/4", 1-1/2", 1-3/4", Face Flush KD Frame Unequal Rabbet April, /16" (49.2) VARIES 1-9/16" (39.7) 5/8" (15.9) 1" (25.4), 1-1/4" (31.8) 1-1/2" (38.1), 1-3/4" (44.5) M 1/2" (12.7) KD M TYPE FUSH GAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9) VARIABE SOFFIT JAMB DEPTH 4-1/2" (114.3) THRU 14" (355.6) (1/8"(3.2) INCREMENTS) NOT AVAIABE WITH 4" (101.6) FACE HEADS NOTE: WHEN CCW MATERIA IS USED IN CONJUNCTION WITH ABOVE, COORDINATE RABBET AND FACE DIMENSIONS 5-3/4" (146.1) JAMB DEPTH STANDARD WITH 7/16" (11.1) RETURNS TO PROVIDE 4-7/8" (123.8) THROAT OPENING. Masonry Flush KD Frame Equal Rabbet 5/8" (15.9) 1-15/16" (49.2) OR 1-9/16" (39.7) VARIES 1-15/16" (49.2) OR 1-9/16" (39.7) 1" (25.4), 1-1/4" (31.8) 1-1/2" (38.1), 1-3/4" (44.5) 2" (50.8) M 1/2" (12.7) KD M TYPE FUSH GAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9) VARIABE SOFFIT JAMB DEPTH 4-7/8" (114.3) THRU 14" (355.6) (1/8"(3.2) INCREMENTS) AVAIABE WITH 4" (101.6) FACE HEADS WITH 2" FACE JAMBS ONY NOTE: WHEN CCW MATERIA IS USED IN CONJUNCTION WITH ABOVE, COORDINATE RABBET AND FACE DIMENSIONS. 5-3/4" (146.1) JAMB DEPTH STANDARD WITH 7/16" (11.1) RETURNS TO PROVIDE 4-7/8" (123.8) THROAT OPENING.

8 5 Masonry Face Flush KD Frame Cased Opening April, 2002 VARIES 3" (76.2) MINIMUM * 1" (25.4) 1-1/4" (31.8) 1-1/2" (30.1) 1-3/4" (44.5) 2" (50.8) MK 1/2" (12.7) KD MK TYPE FUSH GAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9) JAMB DEPTH 3" (76.2) THRU 14" (355.6) (1/8" (3.2) INCREMENTS) NOTE: AVAIABE WITH 4" (101.6) FACE HEAD WITH 4-1/2" (114.3) MINIMUM JAMB DEPTH 5-3/4" (146.1) JAMB DEPTH STANDARD WITH 7/16" (11.1) RETURNS TO PROVIDE 4-7/8" (123.8) THROAT OPENING. * TOTA DOOR ONY MAY BE ABEED Masonry Flush KD G Profile Frame 5/8" (15.9) 1-15/16" (49.2) OR 1-9/16" (39.7) VARIES 2" (50.8) G 2-5/8" (66.7) 1/2" (12.7) KD G TYPE FUSH GAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9) JAMB DEPTH 3" (76.2) THRU 14" (355.6) (1/8" (3.2) INCREMENTS) MIN. 4" JAMB DEPTH FOR ABEED FRAME WITH 1-15/16" RABBET AND 3-1/4" JAMB DEPTH FOR 1-9/16" RABBET. NOTE: 2" (50.8) AND 2-5/8" (66.7) FACE ON JAMBS AVAIABE WITH 4" (101.6) FACE HEAD WITH 4-1/2" (114.3) MINIMUM JAMB DEPTH. 5-3/4" (146.1) JAMB DEPTH STANDARD WITH 7/16" (11.1) RETURNS TO PROVIDE 4-7/8" (123.8) THROAT OPENING.

9 6 Standard Foot Clips April, " (50.8) STANDARD P0030 STANDARD FOOT CIP 16 GA. (1.4) 2" (50.8) 9/32" (7.1) DIA. FACE MINUS 3/8" (9.5) ABE REQUIREMENTS: FACE MINUS 1/2" (12.7) MAXIMUM P GA. FOR FACE WIDTH OVER 4" P GA. P GA. P0030 C TYPE FRAME P0081 DOUBE EGRESS FOOT CIPS FACE MINUS 3/8" (9.5) ABE REQUIREMENTS: FACE MINUS 1/2" (12.7) MAXIMUM P0080 G PROFIE JAMB DEPTH 4" (101.6) OR ESS P0081 G PROFIE GREATER THAN 4" (101.6) JAMB DEPTH

10 7 Adjustable Foot Clip April, 2002 ANCHOR PART NUMBER: P0078 FOOT CIP SHIPPED OOSE WITH 2-#12 SHEET META SCREWS 5/8" (15.7) 3/4" (19.1) 1/2" (12.7) 16 GA. (1.4) 3-5/8" (92) 4-5/8" (117.5) 1/4" (6.4) PER JAMB DEPTH 9/32" (7.1) DIA. 16 GA. (1.4) PER FACE DIMENSION Adjustable Foot Clip - Cased Opening ANCHOR PART NUMBER: P0151 5/8" (15.7) 3/4" (19.1) 1/2" (12.7) FOOT CIP SHIPPED OOSE WITH 2-#12 SHEET META SCREWS 3-5/8" (92) 16 GA. (1.4) 4-5/8" (117.5) 1/4" (6.4) 9/32" (7.1) DIA. PER JAMB DEPTH 16 GA. (1.4) PER FACE DIMENSION

11 8 Common Walls For Masonry Anchor April, 2002 GROUT FU BUTTED MASONRY-BRICK-TIE OR CMU SHIM AS REQUIRED EXISTING MASONRY OR POURED CONCRETE. GROUT OPTIONA WRAP MASONRY-BRICK-TIE OR CMU BUTTED MASONRY-BRICK-TIE OR CMU BUTTED MASONRY-BRICK-TIE OR CMU

12 9 Masonry Wire Anchor April, /2" (63.5) ANCHOR PART NUMBER: P0098 ORDER CODE OOSE: MW 9" (228.6) WIRE DIA. 3/16" (4.8) GAV. ANCHOR MAY BE BENT TO SUIT JAMB DEPTH Concealed Existing Opening Anchor COUNTERSINK HOE FOR 3/8" (9.5) F.H. BOT 9/16" (14.3) DIA. ANCHOR PART NUMBER: CF ANCHORS W/PASTIC PUG PASTIC PUG PART NUMBER: MS PASTIC PUGS 1-1/16" (27) 1-7/8" (47.6) 5-5/8" (142.9) PASTIC PUG 3/8" (9.5) BOT & EXPANSION SHE (NOT PROVIDED) 3/4" (19.1) HOE IN CENTER OF SOFFIT NOT DRIED BY CURRIES NOTE: ANCHORS AVAIABE FOR 5-3/4" (146.1) JAMB DEPTH 2" FACE ONY AVAIABE AS SHIP OOSE PART ONY

13 10 Masonry "T" Anchor June, 2012 ANCHOR PART NUMBER: P0069 ORDER CODE OOSE: M 16 GA. (1.4) 10" (254.0) 2" (50.8) Weld in Type Masonry Anchor ANCHOR PART NUMBER: P0002 ORDER CODE OOSE: M ORDER CODE WEDED: WM 16 GA. (1.4) 10-3/4" (273.1) 2" (50.8)

14 11 EWA Anchor November, 2004 FOR STANDARD RABBETED FRAMES 1-15/16" (49.2) X 1-9/16" (39.7) THE EWA ANCHOR IS AVAIABE IN 5-1/2" (139.7) & 8-1/2" (215.9) SIZES TO FIT 5-3/4" (146.1) & 8-3/4" (222.3) STANDARD RABBETED FRAMES RESPECTIVEY. 3/8" FAT HEAD BOT RECOMMENDED. ANCHOR PART NUMBER: P0070 ORDER CODE OOSE: EWA ORDER CODE WEDED: WEWA -AVAIABE AS SHIP-OOSE ANCHOR -AVAIABE FROM WAREHOUSE AS STOCK #CF SPECIFY 5-1/2" (139.7) OR 8-1/2" (215.9) SIZE 5-1/2" (139.7) 8-1/2" (215.9) 2-9/16" (65.1) 4-1/16" (103.2) 1-1/2" MIN. 18, 16, 14 GA. (38.1) MINIMUM 2-15/16" (74.6) 4-7/16" (112.7) 2-9/16" (65.1) 5-3/4" (146.1) 8-3/4" (222.3) ARC WED 1" (25.4) 15/16" (23.8) 5-3/4" (146.1) 8-3/4" (222.3) DIAMETER 3/8" (9.5) X 1-3/4" (44.5) EMBEDMENT ENGTH OR STEE EXPANSION SHE OR 3/8" (9.5) FATHEAD BOT THE EWA ANCHOR MAY BE TRIMMED TO FIT ANY FRAME OF STANDARD RABBET OR SINGE RABBET 8-3/4" (222.3) OR ESS IN JAMB DEPTH AND EQUA RABBET 8-3/8" (212.7) OR ESS IN JAMB DEPTH * 1-1/2" MINIMUM 12 GA. NOTE: 1-7/8 MIN. STOP WIDTH FOR QM PROFIE

15 12 Pipe Spacer Anchor April, 2002 ANCHOR PART NUMBER: P0044 ORDER CODE OOSE: PS ORDER CODE WEDED: WPS NOTE: FACE DIMENSION FOR PROFIE MUST BE EQUA 3/4" I.D. (19.1) DIAMETER 3/8" (9.5) X 1-3/4" (44.5) EMBEDMENT ENGTH OR STEE EXPANSION SHE OR 3/8" (9.5) FATHEAD BOT 1-1/4" (31.7) MIN. 18, 16, 14 GA.* 1" (25.4) COUNTERSUNK FATHEAD BOT Spacing Bracket Anchor ARC WED * 1-1/2" MIN. FOR 12 GA. ANCHOR PART NUMBER: P0146 ORDER CODE OOSE: SB ORDER CODE WEDED: WSB 16 GA. (1.4) DIAMETER 3/8" (9.5) X 1-3/4" (44.5) EMBEDMENT ENGTH OR STEE EXPANSION SHE OR 3/8" (9.5) FATHEAD BOT VARIES 1-1/4" (31.7) MIN. 18, 16, 14 GA.* 1-13/64" (30.6) COUNTERSUNK FATHEAD BOT 1-13/64" (30.6) 1/2" (12.7) DIA. * 1-1/2" MIN. FOR 12 GA.

16 13 Steel Channel Anchor - Slip-In November, 2014 STANDARD (FUSH) ORDER CODE OOSE: SCF OPTIONA (RECESSED) ORDER CODE OOSE: SCR DOUBE RABBET SINGE RABBET/DE NOTE: MINIMUM FACE OF 1-1/4" (31.8) REQUIRED FOR THIS ANCHOR TYPE

17 14 Steel Channel Anchor-Welded November, 2014 STANDARD (FUSH) ORDER CODE: WSCF OPTIONA (RECESSED) ORDER CODE: WSCR DOUBE RABBET SINGE RABBET/DE EECTRICA CONDUIT (RECESSED) ORDER CODE: ESCR NOTE: FUSH ANCHORS AOW FOR 3/4" (19) DRYWA. NEED TO SPECIFY IF GREATER. FUSH ANCHORS CAN BE USED WITH EECTRICA CONDUIT.

18 15 Wood Stud Anchor January, 2017 SIP IN WOOD STUD ANCHOR - M SERIES FRAME ONY ORDER CODE OOSE: WS A DIMENSIONS ANCHOR PART NUMBER: P SPECIFY STUD WIDTH 16 GA. (1.4) 3-1/4 (82.6) 9/64 (3.6) DIA. 16 GA. (1.4) A 1 (25.4) WED IN WOOD STUD ANCHOR ORDER CODE OOSE: WWS ANCHOR PART NUMBER: 9/64 (3.6) DIA. A 1 (25.4) A DIMENSIONS P SPECIFY STUD WIDTH SIP IN WOOD STUD ANCHOR ORDER CODE OOSE: WS ANCHOR PART NUMBER: A DIMENSIONS P SPECIFY STUD WIDTH Wood Stud Anchors - Double Egress 9/64 (3.6) DIA. 16 GA. (1.4) 1 (25.4) A WED IN WOOD STUD ANCHOR ORDER CODE OOSE: WWS ANCHOR PART NUMBER: 9/64 (3.6) DIA. 16 GA. (1.4) 1 (25.4) A DIMENSIONS P SPECIFY STUD WIDTH A NOTE: SPECIFY JAMB OR HEAD ANCHOR WHEN ORDERING. CURRIES WOOD STUD ANCHORS CAN BE USED WITH WOOD AND META STUDS. BOTH ARE ABE APPROVED.

19 16 Adjustable Multipurpose Anchor October, 2010 ANCHOR PART NUMBER: P0027 ANCHOR CODE: AMP A DIMENSION = JAMB DEPTHS OF 4-3/8" (111.1) THRU 6-3/4" (171.5) 2" (50.8) FACE FUSH M SERIES OR DRYWA C SERIES FIED ADJUSTED TO JAMB DEPTH. AVAIABE AS SHIP OOSE PART ONY FOR USE AS: WOOD STUD ANCHOR WIRE TRUSS ANCHOR STEE CHANNE ANCHOR #12-24 X 1/2" (12.7) SOTTED HEX WASHER HEAD 1/8" (3.2) DIA. A 16 GA. (1.4) BEND OR TRIM EGS TO SUIT WA CONDITIONS Multipurpose Anchor ANCHOR PART NUMBER: P0045 ANCHOR CODE: MP JAMB DEPTHS OF 4-3/4" (120.7) THRU 9-3/4" (247.6) 2" (50.8) FACE FUSH M SERIES OR DRYWA C SERIES 2" (50.8) X 2-5/8" (66.67) G SERIES OR DRYWA CG SERIES BEND OR TRIM EGS TO SUIT WA CONDITIONS 5/32" (4) DIA. NUMBER OF STIFFENERS DEPEND ON JAMB DEPTHS 18 GA. (1.4) UNEQUA RABBETS ONY ON MASONRY WAS

20 17 Multipurpose Anchor Installation - Drywall Return Frame November, 2004 P BEND EGS OF ANCHOR 90 AS SHOWN IN DETAI A (EGS MAY HAVE TO BE BENT FURTHER IN ATER STEPS). DETAI A 2. INSERT ANCHOR INTO FRAME THROAT TITED AT APPROXIMATEY A 50 ANGE AS SHOWN IN DETAI B. 3. THE ANCHOR MUST ASO BE INSERTED AT APPROXIMATEY A 20 ANGE FROM THE RABBETS OF THE FRAME AS SHOWN IN DETAI B. THE FANGES ON THE ANCHOR MUST CEAR THE BACKBEND RETURNS DETAI B PUSH 4. TWIST THE ANCHOR INTO PACE BY APPYING PRESSURE IN THE OPPOSITE DIRECTIONS TO EACH SIDE OF THE ANCHOR AS SHOWN IN DETAI C. 5. ONCE THE ANCHOR HAS SNAPPED INTO PACE, DETAI D, TURN IT UP INTO THE CORRECT POSITION AS SHOWN IN DETAI E EGS SHOUD BE BENT BACK TO THE ORIGINA POSITION IF NECESSARY. DETAI C PUSH DETAI D IFT UP DETAI E

21 18 Ceiling Strut Anchor September, " (101.6) 3/8" (9.5) DIA. 2 PS. 1" (25.4) ANCHOR PART NUMBER: P /8" (28.6) VARIES VARIES 1/4" (6.4) STRUT 1/4" (6.4) X 1" (25.4) STEE BAR 1 REQ D WEDGES STRUT GUIDE 16 GA. (1.4) 2 REQ D 1-1/8" (28.6) 1/4" (6.4) 1/16" (1.6) 1-9/16" (39.7) Mullion Stirrup Anchor 1-1/4" (31.8) WEDGE ANCHOR PART NUMBER: P0089 DIMENSION B VARIES WITH FACE DIMENSION 2" (50.8) FACE MUION B EQUAS 1-1/2" (38.1) 9/32" (7.1) DIA. B 1-1/2" (38.1) VARIES WITH JAMB DEPTH FIED INSTA #8 SMS MINIMUM EACH FACE 12 GA. (2.6)

22 19 Steel Channel Anchor for ead ined Frames November, 2014 STANDARD (FUSH) WED CODE: WSCF- OPTIONA (RECESSED) WED CODE: WSCR- Full Weld KD CONTINUOUS WED JOINTS OF RABBET AND SOFFIT CONTINUOUS WED FACE SEAM GRIND AND FINISH SMOOTH WED CODE: FW BEND TABS TOWARD WA

23 20 Seam Weld Flush KD February, 2013 WED CODE SW (KD) BEND TABS TOWARD WA CONTINUOUS WED FACE SEAM GRIND AND FINISH SMOOTH Saw Miter Weld WED CODE SMT WED CODE SMW GRIND FACE AND FINISH SMOOTH TACK WED RABBET AND SOFFIT GRIND FACE AND FINISH SMOOTH CONTINUOUS WED INSIDE OF MITER

24 21 Saw Butt Weld April, 2002 WED CODE BEW (<3) WED CODE BET (<3) WED CODE SBW (>3) WED CODE SBT (>3)

25 22 Corner Welds July, 2003 WED CODE BEF 10

26 23 Splice Joints April, 2002 WED CODE FSP WED CODE WSP NOTE: FACTORY WEDED FRAMES EXCEEDING 9' X 14' WI BE PROVIDED WITH FIED SPICES Saw Miter Only WED CODE SMO NOTE: PREPARED FOR DISTRIBUTOR WEDING WED CODE SBE WED CODE EBE EXACT NOTCH TOP JAMBS NOTCH BOTH ENDS. (BANK OR HEADS) EXACT NO NOTCH

27 24 Field Splice Frames June, 2010 FRAMES FACTORY WEDED AT CURRIES: PROVIDE FIED SPICES FOR FRAMES THAT EXCEED OVERA SIZE SHOWN. 9'0" (2743) HEIGHT 14'0"(4267) HEIGHT 14'0"(4267) WIDTH 9'0" (2743) WIDTH FRAMES FACTORY WEDED AT REGIONA SERVICE CENTERS: 9'0" (2743) HEIGHT 14'0"(4267) HEIGHT 14'0"(4267) WIDTH 9'0" (2743) WIDTH

28 25 Die Mitered Weld Stainless Steel February, 2014 FU FACE WED AND INTERMITTENT SOFFET AND RABBET WEDS THROAT OPENING 1" (25.4) ESS THAN JAMB DEPTH JAMB DEPTH JAMB DEPTH THROAT OPENING 1" (25.4) ESS THAN JAMB DEPTH HEAD JAMB 304 OR 316 STAINESS STEE FINISH: 2B MI #4 BRUSHED SATIN #6 FINE SATIN #8 MIRROR XB X BEND

29 26 Stainless Steel Sidelight Frame February, 2014 VERTICA MEMBERS BUTT AT SI AND HEAD JAMB DEPTH 304 OR 316 STAINESS STEE FINISH: 2B MI #4 BRUSHED SATIN #6 FINE SATIN #8 MIRROR XB X BEND WEDED JAMB DEPTH

30 27 Half Sidelite Window Option July, 2003 OPTION B MOST COMMON REMOVE BACKSIDE OF MUION NOTE: MAY BE ABEED WHEN PROPERY WEDED. FIER PATE WITH STOP EXPOSED SEAM UNESS FACTORY WEDED SEAM OPTION C AS REQUIRED OPTION A AS REQUIRED SPICE WED SECTION TO MUION FI AND GROUND SMOOTH, ABEED WHEN FUY WEDED.

31 28 Cut and Notch Options April, 2002 CORNER: KD STANDARD WHEN POSSIBE MUST MEET KD PARAMETERS SAW MITER:* IF FACES OF HEAD AND JAMB ARE EQUA 1. EXCEPT: 4" (101.6) FACE HEAD TO 2" (50.8) FACE JAMB BUTT END:* IF FACES ARE UNEQUA * SMO OR SBE MUST BE NOTED IN CONSTRUCTION COUMN. NOTE: MAY BE ABEED WHEN PROPERY WEDED SAW MITER KD BUTT END NOTE: MAY BE ABEED WHEN FACE WEDED

32 29 Cut and Notch Options April, 2002 STRIKE MUION: NOTCH TOP EXCEPTION: WI RUN THROUGH HEAD IF HEAD PROFIE IS DIFFERENT ON GASS SIDE EXAMPE: M PROFIE AT DOOR OPENING G PROFIE AT WINDOW SIDE RUN MUION THROUGH IF HEAD FACES ARE DIFFERENT FROM DOOR SIDE TO GASS SIDE OR IF FIED SPICE IS REQUIRED NOTE: MAY BE ABEED WHEN PROPERY WEDED NOTE: PROVIDES ACCESS FOR EECTRICA CONDUIT OR GROUT

33 30 Cut and Notch Options April, 2002 HORIZONTA MUION: NOTCH BOTH ENDS TO BUTT BETWEEN VERTICA MEMBERS IS STANDARD PREPARATION NOTE: MAY BE ABEED WHEN PROPERY WEDED NOTCH STOP OF JAMB TO RECEIVE MUION TYPICA REMOVABE MUION PREPARATION OPTIONA STANDARD

34 31 Cut and Notch Options April, 2002 MUION: NOTCH TOP AND BOTTOM, WI RUN THROUGH FROM HEAD TO TOP OF SI 1. EXCEPTION: WI RUN MUION THROUGH TO FOOR RATHER THAN SPICE 2 SECTIONS OF SI TOGETHER 2. EXCEPTION: RUN MUION THROUGH HEAD AND SI IF FIED SPICE IS REQUIRED NOTE: MAY BY ABEED WHEN PROPERY WEDED SIS: NOTCH BOTH ENDS TO BUTT BETWEEN VERTICA MEMBERS STANDARD STANDARD OPTIONA

35 32 Saw Butt End June, 2009 WA NOTCH JAMB FOR DRYWA WA CONSTRUCTION NOTE: MAY BE ABEED WHEN PROPERY WEDED OPTIONA STANDARD Drywall KD CG Profile Corner Details #8 SCREW (MS002485) (REQUIRED ON A FIRE RATED FRAMES)

36 33 Drywall KD Frame Corner Clip Detail June, 2009 C PROFIE CORNER 2-3/8" (60.3) HEAD 2" FACE 2-3/8" (60.3) WED PROJECTIONS JAMB 3-1/2" (88.9) #8 SCREW (MS002485) (REQUIRED ON A FIRE RATED FRAMES) *RETURN FIER: P0071 HEAD 2" (50.8) FACE SPOT WEDS BY CURRIES HEAD 4" (101.6) FACE JAMB

37 34 Security Anchor April, 2002 ANCHOR PART NUMBER: P /2" (88.9) VARIES 16 GA. (1.4) COMPRESSION ANCHOR PER JAMB DEPTH 1-1/8" (28.6) 1-1/8" (28.6) SECURITY ANCHOR 45" (1143) TYPICA BOTTOM OF FRAME Drywall Frame Compression Anchor ANCHOR PART NUMBER: P0026 (2" FACE) ANCHOR PART NUMBER: P0018 (1-1/2" TO 1-3/4" FACE) 1" (25.4) MIN. 5/8" (15.8) MAXIMUM TRAVE 3-1/2" (88.9) COMPRESSION ANCHOR

38 35 Drywall KD Frame Standard Base Anchor November, 2004 ANCHOR HOES COUNTERSUNK #6 SCREW BOTH SIDES 2" FACE ONY 3/4" (19.1) 5/8" (15.9) MINIMUM JAMB DEPTH 3-3/8 (85.7) 2" (50.8) Drywall KD Frame Optional Base Anchor ANCHOR PART NUMBER: P0087 7/8" (22.2) 16 GA. (1.4) 1" (25.4) 1/2" (12.7) 1/2" (12.7) 3/4" (19) C 3-1/4" (82.6) 3/16" (4.8) DIA. FOOR NOTE: REQUIRED ON 1-1/2" (38.1), 1-3/4" (44.5) FACE DRYWA FRAMES. 3", 3-1/8", 3-1/4", JAMB DEPTHS.

39 36 Drywall CG Profiles April, 2002 VARIES JAMB DEPTHS 3" (76.2) 14" (355.6) 1-15/16" (49.2) OR 1-9/16" (39.7) 5/8" (25.9) 2-5/8" (66.7) CG 2" (50.8) 3/8" (9.5) 3/8" (9.5) 1/2" (12.7) 1/2" (12.7) GAUGE - 18 GA. (1.2), 16 GA. (1.4) NOTE: AVAIABE WITH 4" (101.6) FACE HEAD WITH 4-1/2" (114.3) MINIMUM JAMB DEPTH Compression Anchor System Narrow Jamb Depth CG PROFIE * 1-3/8" (34.9) DOOR - 3" (76.2) JAMB DEPTH 1-3/4" (44.5) DOOR - 3" (76.2), 3-1/8" (79.4), 3-1/4" (82.6), 3-3/8" (85.7) JAMB DEPTH C -COMPRESSION ANCHORS 3-1/2" (88.9) ROUGH OPENING WIDTH EQUAS NOMINA DOOR OPENING: PUS 2-13/16" (71.4) ROUGH OPENING HEIGHT EQUAS NOMINA DOOR OPENING: PUS 3/4" - 1" MAX (19.1) - (25.4) STRAP BASE ANCHOR STROKE 3/4" (19.1) * CG PROFIE JAMB DEPTHS NOT ISTED ABOVE USE STD. DRYWA ROUGH OPENING DIMENSIONS

40 37 Drywall KD Frame Unequal Rabbet April, /16" (49.2) VARIES 1-9/16" (39.7) 5/8" (15.9) 1-1/2" (38.1) 1-3/4" (44.5) 2" (50.8) C 3/8" (9.5) 1/2" (12.7) KD DRYWA GAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9) * UNEQUA RABBET JAMB DEPTH 4-1/2" (114.3) THRU 14" (355.6) (1/8" (3.2) INCREMENTS) 2" (50.8) FACE AVAIABE WITH 4" (101.6) HEADS NOTE: 14 GA. AVAIABE WITH 2" (50.8) FACE ONY Drywall KD Frame Equal Rabbet 1-15/16" (49.2) OR 1-9/16" (39.7) VARIES 1-15/16" (49.2) OR 1-9/16" (39.7) 5/8" (15.9) 1-1/2" (38.1) 1-3/4" (44.5) 2" (50.8) C 3/8" (9.5) 1/2" (12.7) KD DRYWA GAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9) * UNEQUA RABBET JAMB DEPTH 4-7/8" (123.8) THRU 14" (355.6) (1/8" (3.2) INCREMENTS) 2" (50.8) FACE AVAIABE WITH 4" (101.6) HEADS AVAIABE IN COMMUNICATING FRAMES NOTE: 14 GA. AVAIABE WITH 2" (50.8) FACE ONY

41 38 Drywall KD Frame Cased Opening April, 2002 VARIES 3" (76.2) MINIMUM 1-1/2" (38.1) 1-3/4" (44.45) 2" (50.8) CK 3/8" (9.5) 1/2" (12.7) KD DRYWA GAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9) JAMB DEPTH 3" (76.2) THRU 14" (355.6) (1/8" (3.2) INCREMENTS) 14 GA. AVAIABE W/2" FACE ONY NOTE: AVAIABE WITH 4" (101.6) FACE HEAD WITH 4-1/2" (114.3) MINIMUM JAMB DEPTH WITH 2" FACE JAMBS ONY. Drywall KD CG Profile Frame 1-15/16" (49.2) OR 1-9/16" (39.7) VARIES 5/8" (50.8) 2" (50.8) CG 2-5/8" (66.7) 3/8" (9.5) 1/2" (12.7) KD CG PROFIE DRYWA GAUGE - 18 GA. (1.2), 16 GA. (1.4) JAMB DEPTH 3" (76.2) THRU 14" (355.6) (1/8" (3.2) INCREMENTS) NOTE: 2" (50.8) AND 2-5/8" (66.7) FACE ONY

42 39 Drywall Cased Opening Compression Anchor April, 2013 STIFFENER PART NUMBER: P0093 2" (50.8) EG 16 GA. (1.4) 2" (50.8) VARIES 3/4" (19.1) NOTE: STIFFENER ADDED TO PREVENT DISTORTION OF FRAME WHEN TIGHTENING ANCHOR CM Profile Frames CM 3-1/2" (88.9) - 14" (355.6) CMG 3" (76.2) - 14" (355.6) 2" (50.8) 3/8" (9.5) CM CMG 1/2" (12.7) CM PROFIE FRAMES DO NOT HAVE THE COMPRESSION BAR NOR BASE ANCHORS. THEY DO HAVE FOOTCIPS WEDED IN AND ARE FURNISHED WITH OOSE DRY- WA ANCHORS, WEDED IN ANCHORS ARE OPTIONA. SAME K.D. CORNER CAPABIITIES AS THE C FRAME. FOOTCIPS

43 40 Drywall KD Frame ("C" Profile) Installation Instructions July, CONSTRUCT WA WITH ROUGH OPENING HEIGHT EQUA TO FINISHED OPENING HEIGHT PUS 3/4" (19.1) TO 1" (25.4) MAX., ROUGH OPENING WIDTH IS AS FOOWS: A) FOR 2" (50.8) FACE FRAMES-OPENING WIDTH PUS 2-1/8" (54.0) TO 2-3/8" (60.3) B) FOR 1-3/4" (44.5) AND 1-1/2" (38.1) FACE FRAMES-OPENING WIDTH PUS 2" (50.8) C) FOR C AND CG PROFIES, 3" (76.2) JAMB DEPTH 1-9/16" (39.7) RABBET AND 3" (76.2), 3-1/8" (79.4), 3-1/4" (82.6) AND 3-3/8" (85.7) JAMB DEPTH 1-15/16" (49.2) RABBET FRAMES-OPENING WIDTH PUS 2-13/16" (71.4), A OTHER C AND CG PROFIE FRAMES-OPENING WIDTH PUS 2-1/8" (54.0) TO 2-3/8" (60.3) d) FOR 2" (508) FACE CASED OPENING - OPENING WIDTH PUS 2-1/4" (572) 2. BOTTOM OF FRAME MUST SET ON A SOID SURFACE. 3. IF WRAP-AROUND BASE ANCHOR IS USED, NOTCH DRYWA IN THAT AREA. 4. RETRACT COMPRESSION BARS IN THE JAMBS BY TURNING SCREWS COUNTER COCKWISE AND INSTA ONE JAMB IN POSITION ON WA. 5. INSERT FRAME HEAD UNDER THE CORNER CIPS OF THE JAMB AND RAISE INTO POSITION. 6. INSERT THE CORNER CIPS OF THE REMAINING JAMB INTO THE OPPOSITE END OF THE HEAD AND POSITION JAMB ON WA. 7. OCATE A REMOVABE FRAME SPACING BAR AT BASE OF CENTERED FRAME TO MAINTAIN PROPER OPENING WIDTH DURING INSTAATION. 8. EVE, SQUARE AND PUMB FRAME AND INSTA BASE ANCHOR SCREWS THROUGH COUNTERSINK HOES IN FRAME FACE AND INTO FOOR PATE. 9. SQUARE TOP OF FRAME AND TIGHTEN COMPRESSION BARS BY TURNING SCREWS COCKWISE. (DO NOT OVERTIGHTEN). 10. INSTA (4) NO. 8 X 1/2" (12.7) SHEET META SCREWS AT THE CORNERS OF THE HEAD TO ATTACH HEAD TO JAMBS (REQUIRED FOR FIRE RATED FRAMES).

44 41 Drywall KD Borrowed ite July, 2007 NOTE A: NOTE B: ROUGH OPENING HEIGHT FOR 2" (50.8) FACE FRAMES EQUAS GASS OPENING SIZE PUS 2-1/2" (63.5) INCUDING CASED OPENING NOTE A: ROUGH OPENING HEIGHT FOR 1-1/2" (38.1) & 1-3/4" (44.5) FACE FRAMES EQUAS GASS OPENING SIZE PUS 2" (50.8) ROUGH OPENING WIDTH FOR 2" (50.8) FACE FRAMES EQUAS GASS OPENING SIZE PUS 2-1/2" (63.5) INCUDING CASED OPENING ROUGH OPENING WIDTH FOR 1-1/2" (38.1) & 1-3/4" (44.5) FACE FRAMES EQUAS GASS OPENING SIZE PUS 2" (50.8) VARIABE FACE OVERA FRAME WIDTH GASS OPENING 1'6" (457.2) MINIMUM NOTE: 5/8" (15.8) X 5/8" (15.8) GASS STOPS ARE PUNCHED AND CUT TO ENGTH REMOVABE STOPS MATCH FIXED STOP ENGTH AND ARE SHIPPED OOSE C C ROUGH OPENING HEIGHT SEE NOTE A COMP. BAR COMP. BAR GASS OPENING STD. STD. OVERA FRAME HEIGHT C C 4" (101.6) FACE HEADS & SIS ARE NOT AVAIABE CG PROFIE - SEE NEXT PAGE ROUGH OPENING WIDTH SEE NOTE B VARIABE FACE KD BORROWED ITE (DRYWA FRAME ONY) ORDER OF INSTAATION - A) PACE RIGHT SIDE VERTICA JAMB MEMBER INTO OPENING; B) INSTA SI MEMBER AND ASSEMBE COR- NER #1; C) THEN INSTA HEAD MEMBER AND ASSEMBE CORNER #2 D) WHIE INSTAING THE REMAINING EFT VERTICA JAMB MEMBER IT MAY BE NECESSARY TO EXTEND THE HEAD (CORNER #3) AND SI (CORNER #4) TO THEIR ROUGH OPENING IMITATIONS FOR EASIER IN- STAATION; E) THEN ASSEMBE CORNER #3 AND FINAY SNAP INTO POSITION THE REMAINING CORNER #4; F) INSTA SCREWS THROUGH FRAME RETURNS INTO CORNER CIPS; G) ADJUST COMPRESSION BARS UNTI EVE AND PUMB.

45 42 Single Rabbet Drywall KD Borrowed ite July, 2007 CG PROFIE - COMPRESSION BAR RABBET MOUNTED. JAMB DEPTHS INCUDE 3" (76.2), 3-1/8" (79.4), 3-1/4" (82.5), 3-3/8" (85.7) X 1-15/16" (49.2) RABBET AND 3" (76.2) X 1-9/16" (39.7) RABBET NOTE A: NOTE B: ROUGH OPENING HEIGHT FOR 2" (50.8) FACE FRAMES EQUAS GASS OPENING SIZE PUS 2-3/4" (69.8) ROUGH OPENING WIDTH FOR 2" (50.8) FACE FRAMES EQUAS GASS OPENING SIZE PUS 2-1/2" (63.5) OVERA FRAME WIDTH VARIABE FACE GASS OPENING 1'6" (457.2) MINIMUM C C HEIGHT WIDTH SEE NOTE A COMP. BAR COMP. BAR GASS OPENING OVERA FRAME HEIGHT 4" (101.6) 4" (101.6) #8 SHEET C C META SCREW (8 PACES) ROUGH OPENING WIDTH SEE NOTE B VARIABE FACE KD BORROWED ITE (DRYWA FRAME ONY) ORDER OF INSTAATION - A) PACE RIGHT SIDE VERTICA JAMB MEMBER INTO OPENING; B) INSTA SI MEMBER AND ASSEMBE COR- NER #1; C) THEN INSTA HEAD MEMBER AND ASSEMBE CORNER #2 D) WHIE INSTAING THE REMAINING EFT VERTICA JAMB MEMBER IT MAY BE NECESSARY TO EXTEND THE HEAD (CORNER #3) AND SI (CORNER #4) TO THEIR ROUGH OPENING IMITATIONS FOR EASIER IN- STAATION; E) THEN ASSEMBE CORNER #3 AND FINAY SNAP INTO POSITION THE REMAINING CORNER #4; F) INSTA SCREWS THROUGH FRAME RETURNS INTO CORNER CIPS. G) ADJUST COMPRESSION BARS UNTI EVE AND PUMB.

46 43 Throat Filler for Drywall Frames April, 2002 DOUBE FACE TAPE 1/8" (3.2) FU SIZE ONE FIER STRIP TWO FIER STRIPS THROAT REDUCED BY 1/8" (3.2) THROAT FIER STRIPS ARE MADE OF WHITE RIGID PVC WITH RESIIENT DOUBE FACE TAPE FOR APPICATION TO THE FRAME BACKBEND OR AFTER THE FRAME HAS BEEN INSTAED. SUPPIED IN ENGTHS OF 7 FT. 3 IN. (2209.8) TO ACCOMMODATE MOST JAMB HEIGHTS WITH A CONTINUOUS STRIP. THROAT REDUCED BY 1/4" (6.4) NOTE: THROAT FIER IS NOT AOWED ON ABE FRAMES INSTAATION 1. FOR BEST RESUTS INSTA FRAME IN OPENING FIRST. DO NOT TIGHTEN COMPRESSION ANCHORS. 2. CUT JAMB FIER STRIPS TO OVERA ENGTH OF JAMB BACKBEND. CUT HEAD FIER STRIP 1" (25.4) UNDER OVERA ENGTH OF HEAD BACKBEND. 3. REMOVE PROTECTIVE FIM FROM ADHESIVE TAPE AND APPY FIER STRIPS TO FRAME BACKBENDS WITH 1/8" (3.2) THICK EG BETWEEN BACKBEND RETURN AND WA. APPY PRESSURE TO SEAT FIRMY. 4. SQUARE FRAME, TIGHTEN COMPRESSION ANCHORS, INSTA BASE ANCHORS AND RESEAT FIER STRIPS IF NECESSARY. 1/2" (12.7) OVERA ENGTH OF HEAD BACKBEND ENGTH OF HEAD FIER 1/2" (12.7) FIER EQUAS OVERA ENGTH OF BACKBEND

47 44 CURRIES Standard Hinge & Strike ocations for 1-3/4" Frames September, 2013 SIZE A B C 6 8 (2032) 7-1/4 (184.2) 30-1/4 (768.4) 12-1/4 (311.2) 6 10 (2082.8) 7-1/4 (184.2) 31-1/4 (793.8) 12-1/4 (311.2) 7 0 (2133.6) 7-1/4 (184.2) 32-1/4 (819.2) 12-1/4 (311.2) 7 2 (2184.4) 7-1/4 (184.2) 33-1/4 (844.6) 12-1/4 (311.2) 7 10 (2387.6) 7-1/4 (184.2) 37-1/4 (946.2) 12-1/4 (311.2) 8 0 (2438.4) 7-1/4 (184.2) 38-1/4 (971.6) 12-1/4 (311.2) HINGE SIZE MAY VARY C OCATION REMAINS THE SAME HINGE BACKSET: 5/16" (7.9) FOR 1-3/4" (44.5) DOOR 5/8" (15.9) FOR 2" (50.8) DOOR 5/8" (15.9) FOR 2-1/4" (57.2) DOOR DOOR RABBETS: 1-15/16" (49.2) FOR 1-3/4" (44.5) DOOR 2-3/16" (55.6) FOR 2" (50.8) DOOR FOR USE WITH THREE HINGES 4-1/2" (114.3) OR 5" (127) * A C B 4-7/8" (123.8) STRIKE C C B C C 40" (1016) STANDARD NOTE: FOR FRAMES UNDER 60" TA WE WI CENTER THE STRIKE FOR A MANUFACTURERS OCATIONS UNESS NOTED OTHERWISE ON THE ORDER. * STRIKE BACKSET: 5/16" (7.9) FOR 1-3/4" (44.5) DOOR 1/2" (12.7) FOR 2" (50.8) DOOR

48 45 CURRIES Standard Hinge & Strike ocations for 1-3/4" Frames September, 2013 SIZE A B C 6'8" (2032) 7-1/4" (184.2) 20-1/8" (511.2) 12-3/8" (314.3) 6'10" (2082.8) 7-1/4" (184.2) 20-7/8" (530.2) 12-1/8" (308) 7'0" (2133.6) 7-1/4" (184.2) 21-1/2" (546.1) 12-1/4" (311.2) 7'2" (2184.4) 7-1/4" (184.2) 22-1/8" (562) 12-3/8" (314.3) 7'10" (2387.6) 7-1/4" (184.2) 24-7/8" (631.8) 12-1/8" (308) 8'0" (2438.4) 7-1/4" (184.2) 25-1/2" (647.7) 12-1/4" (311.2) 9'0" (2743.2) 7-1/4" (184.2) 29-1/2" (749.3) 12-1/4" (311.2) 10'0" (3048) 7-1/4" (184.2) 33-1/2" (850.9) 12-1/4" (311.2) HINGE SIZE MAY VARY C OCATION REMAINS THE SAME. HINGE BACKSET: 5/16" (7.9) FOR 1-3/4" (44.5) DOOR. 5/8" (15.9) FOR 2" (50.8) DOOR DOOR RABBETS: 1-15/16" (49.2) FOR 1-3/4" (44.5) DOOR. 2-3/16" (55.6) FOR 2" (50.8) DOOR. FOR USE WITH FOUR HINGES 4-1/2" (114.3) OR 5" (127) * A C B C 4-7/8" (123.8) STRIKE B C C B C C * STRIKE BACKSET: 5/16" (7.9) FOR 1-3/4" (44.5) DOOR 1/2" (12.7) FOR 2" (50.8) DOOR 40" (1016) STANDARD NOTE: FOR FRAMES UNDER 60" TA WE WI CENTER THE STRIKE FOR A MANUFACTURERS OCATIONS UNESS NOTED OTHERWISE ON THE ORDER.

49 46 CURRIES Standard Hinge & Strike ocations for 1-3/8" Frames September, 2013 SIZE A B C 6'8" (2032) 9-3/4" (247.7) 59-7/8" (1520.8) 10-3/8" (263.5) 6'10" (2082.8) 9-3/4" (247.7) 61-7/8" (1571.6) 10-3/8" (263.5) 7'0" (2133.6) 9-3/4" (247.7) 63-7/8" (1622.4) 10-3/8" (263.5) 7'2" (2184.4) 9-3/4" (247.7) 65-7/8" (1673.2) 10-3/8" (263.5) HINGE SIZE MAY VARY, C OCATION REMAINS THE SAME. HINGE BACKSET: 5/16" (7.9) FOR USE WITH TWO HINGES 1-3/8" (34.9) DOOR 3-1/2" (88.9) OR 4" (101.6) STRIKE BACKSET 3/16" (4.8) A C 2-3/4" (69.9) STRIKE B C 40-5/16" (1023.9) STANDARD C C NOTE: FOR FRAMES UNDER 60" TA WE WI CENTER THE STRIKE FOR A MANUFACTURERS OCATIONS UNESS NOTED OTHERWISE ON THE ORDER.

50 47 CURRIES Standard Hinge & Strike ocations for 1-3/8" Frame September, 2013 SIZE A B C 6'8" (2032) 9-3/4" (247.7) 29-15/16" (760.4) 10-3/8" (263.5) 6'10" (2082.8) 9-3/4" (247.7) 30-15/16" (785.8) 10-3/8" (263.5) 7'0" (2133.6) 9-3/4" (247.7) 31-15/16" (811.2) 10-3/8" (263.5) 7'2" (2184.4) 9-3/4" (247.7) 32-15/16" (836.6) 10-3/8" (263.5) HINGE SIZE MAY VARY, HINGE BACKSET: 5/16" (7.9) OCATION REMAINS THE SAME. C FOR USE WITH THREE HINGES 1-3/8" (34.9) DOOR 3-1/2" (88.9) OR 4" (101.6) STRIKE BACKSET 3/16" (4.8) A C B 2-3/4" (69.9) STRIKE C C B 40-5/16" (1023.9) STANDARD C C NOTE: FOR FRAMES UNDER 60" TA WE WI CENTER THE STRIKE FOR A MANUFACTURERS OCATIONS UNESS NOTED OTHERWISE ON THE ORDER.

51 48 CURRIES Standard Hinge & Strike ocations for 1-3/4" Dutch Frame November, 2004 SIZE A B C D E 6'8" (2032) 7-1/4" (184.2) 24-1/4" (616) 13-1/2" (342.9) 22-3/4" (577.9) 12-1/4" (311.2) 6'10" (2082.8) 7-1/4" (184.2) 26-1/4" (666.6) 13-1/2" (342.9) 22-3/4" (577.9) 12-1/4" (311.2) 7'0" (2133.6) 7-1/4" (184.2) 28-1/4" (717.6) 13-1/2" (342.9) 22-3/4" (577.9) 12-1/4" (311.2) 7'2" (2184.4) 7-1/4" (184.2) 30-1/4" (768.4) 13-1/2" (342.9) 22-3/4" (577.9) 12-1/4" (311.2) 7'10" (2387.6) 7-1/4" (184.2) 35-1/4" (895.4) 16-1/2" (419.1) 22-3/4" (577.9) 12-1/4" (311.2) 8'0" (2438.4) 7-1/4" (184.2) 37-1/4" (946.2) 16-1/2" (419.1) 22-3/4" (577.9) 12-1/4" (311.2) 9'0" (2743.2) 7-1/4" (184.2) 49-1/4" (1251) 16-1/2" (419.1) 22-3/4" (577.9) 12-1/4" (311.2) 10 0" (3048) 7-1/4" (184.2) 61-1/4" (1555.8) 16-1/2" (419.1) 22-3/4" (577.9) 12-1/4" (311.2) HINGE SIZE MAY VARY, C OCATION REMAINS THE SAME. HINGE BACKSET: 5/16" (7.9) STRIKE BACKSET 5/16" (7.9) DUTCH DOOR 4-1/2" (114.3) OR 5" (127) A C 4-7/8" (123.8) STRIKE B C NOTE: MAXIMUM FIRE ABE WIDTH: 3'8" (1117.6) C C SHEF HEIGHT IS 42" (1066.8) STANDARD C C PEASE INDICATE WHEN ADA COMPIANCE IS REQUIRED. 48" C IS NOT PRACTICA WITH SOME DEADOCKS. D 35" (889) STANDARD 50" (1270) STANDARD * * E C

52 49 Frame Standard Rabbet Dimensions April, 2002 DOOR THICKNESS DIMENSIONS 1-3/8" 1-9/16" (39.7) 1-3/4" 1-15/16" (49.2) 2"* 2-3/16" (55.5) 2-1/4"* 2-7/16" VARIES DOOR THICKNESS DIMENSIONS 1-3/8" 1-15/16" (49.2) 1-3/4" 1-9/16" (39.7) 2"* 1-9/16" (39.7) 2-1/4"* 1-9/16" (39.7) 5/8" (15.8) 2" (50.8) DOUBE RABBET 1/2" (12.7) DOOR THICKNESS DIMENSIONS 1-3/8" 1-9/16" (39.7) 1-3/4" 1-15/16" (49.2) 2"* 2-3/16" (55.5) 2-1/4"* 2-7/16" VARIES 5/8" (15.8) 2" (50.8) SINGE RABBET 1/2" (12.7) DOOR THICKNESS DIMENSIONS 1-3/8" 1-9/16" (39.7) 1-3/4" 1-15/16" (49.2) 2"* 2-3/16" (55.5) 2-1/4"* 2-7/16" VARIES DOOR THICKNESS DIMENSIONS 1-3/8" 1-15/16" (49.2) 1-3/4" 1-9/16" (39.7) 2"* 1-9/16" (39.7) 2-1/4"* 1-9/16" (39.7) 5/8" (15.8) 2" (50.8) MUION * NOT AVAIABE KNOCKDOWN (KD)

53 50 4-1/2" Ultima Hinge Reinforcement July, 2010 DEFAUT REINFORCEMENT FOR A 4-1/2" STANDARD AND HEAVYWEIGHT HINGES DRIED AND TAPPED PER HINGE TEMPATE PROJECTIONS FOR RESISTANCE WEDING 1-7/32" (30.9) 5-9/16" (141.3) 9" (228.6) 18 GA. (1.2) STEE SHIM PATE 7 GA. (4.5) STEE MUDCAP STANDARD ON M SERIES FRAME OFFSET IN 16 GA. (1.4) FRAME WITH SHIM PATE.134" (3.4) WITHOUT SHIM PATE.180 (4.6).134" (3.4).180" (4.6) TO REMOVE SHIM PATE, INSERT FAT SCREWDRIVER BETWEEN SHIM AND REINFORCEMENT, AND PRY SHIM AWAY FROM REINFORCEMENT. NOTE: 1) IF SHIM IS REMOVED, PRIME PAINT HINGE REINFORCEMENT. 2) NOT RECOMMENDED FOR CONVERSION TO EECTRIC HINGE PREPARATION.

54 51 5" Hinge Reinforcement November, 2004 DRIED AND TAPPED PER HINGE TEMPATE STD PROJECTIONS FOR RESISTANCE WEDING 1-5/8" (41.3) 5-9/16" (141.3) 9" (228.6) 7 GA. (4.5) STEE Heavy 5" Hinge Reinforcement NOTE: EECTRICA HINGE PREPARATION AVAIABE PER TEMPATE DRIED AND TAPPED PER HINGE TEMPATE STD INDICATES HEAVY WEIGHT HINGE REINFORCEMENT PROJECTIONS FOR RESISTANCE WEDING 1-5/8" (41.3) 5-9/16" (141.3) 9" (228.6) 7 GA. (4.5) STEE

55 52 EH - Electric Hinges July, 2011 PER TEMPATE 5/8" X 13/16" SOTS TYPICA TYPICA 4-1/2" EECTRIC HINGE PREPARATION SHOWN FITS MANY EECTRIC HINGES. OTHER EECTRIC HINGE PREPARATIONS WI BE PREPARED PER THE HINGE TEMPATE. NOTE: EECTRIFIED HINGE REINFORCEMENT AVAIABE AS OOSE PART #FH0300

56 53 HFG Hinge Strap Reinforcement October, 2013 HIGH FREQUENCY HINGE REINFORCEMENT STRAPS 14 GA. (2.0) REINFORCEMENT 7 GA. (4.5) X 1-1/4" (31.8) X 9" (229) HINGE REINFORCEMENT. DRIED AND TAPPED FOR UNC (STANDARD) (1/4-20 UNC OPTIONA) HOE FOR ABUSE-RESISTANT STUD (OPTIONA) MUDCAP WED AS SHOWN

57 54 Full Width Hinge Reinforcement November, 2004 ARC WED FU WIDTH AONG EACH END IN RABBETS (ONY WHEN SPECIFIED). STANDARD WEDS INDICATED WITH AT END. 7 GA. (4.5) X JAMB DEPTH MINUS 1/2" (12.7) X 10" (254) HINGE REINFORCEMENT. DRIED AND TAPPED FOR UNC (STANDARD) (1/4-20 UNC OPTIONA) HOE FOR ABUSE-RESISTANT STUD (OPTIONA) COVERBOX

58 55 Continuous Hinge Reinforcement September, 2005 SURFACE MOUNTED TYPE CONCEAED MOUNTED TYPE HGCF CODE HGCR CODE 3/4" (19.1) 3/4" (19.1) 12 GA. (2.6) REINFORCING 12 GA. (2.6) REINFORCING 1/4" (6.4) NOTE: HINGE MANUFACTURERS RECOMMEND REINFORCEMENTS ON 20, 18, 16 GAUGE FRAMES. 1/4" (6.4)

59 56 Security Hinge and Grout Guard November, 2004 ARC WED FU WIDTH AONG EACH END PROJECTIONS FOR RESISTANCE WEDING 7 GA. (4.5) X 1-19/32" (40.4) X 9" (228.6) HINGE REINFORCEMENT. DRIED AND TAPPED FOR UNC (STANDARD) (1/4-20 UNC OPTIONA) OFFSET PER HINGE THICKNESS HOE FOR ABUSE-RESISTANT STUD PER TEMPATE AS REQUIRED. 16 GA. (1.4) COVERBOX SPOT WEDED OVER HINGE REINFORCING.

60 57 Electric Hinge and Grout Guard November, 2004 ARC WED FU WIDTH AONG EACH END (OPTIONA) WED PROJECTIONS FOR RESISTANCE WEDING 7 GA. (4.5) X 1-19/32" (40.4) X 9" (228.6) HINGE REINFORCEMENT. DRIED AND TAPPED FOR UNC (STANDARD) (1/4-20 UNC OPTIONA) OFFSET PER HINGE THICKNESS EECTRICA CONDUIT KNOCKOUT 16 GA. (1.4) GROUT GUARD COVER- BOX SPOT WEDED OVER HINGE RE- INFORCING. EECTRICA HINGE WIRE ACCESS HOE PER TEMPATE. #8 PAN HEAD SCREW NOTE: JUNCTION BOXES ARE NOT CAUKED AT THE FACTORY. TO BE FIED CAUKED BY INSTAATION CONTRACTOR.

61 58 HGA - Anchor Hinge Preparation April, GA. (4.5) HINGE REINF. CURRIES DOES NOT DRI AND TAP FOR HINGE SCREWS, UNESS FRAME IS FACTORY WEDED AND PHYSICA SAMPES ARE PROVIDED. IF FRAME IS STICK OR KD THE PARTS ARE SHIPPED OOSE AND ARE NOT WEDED TOGETHER, DRI AND TAP IN FIED. ARC WED DOOR RABBET IS 1-15/16" (49.2)

62 59 HGD - Hinge - Double Acting April, GA. (2.6) REINFORCING VERTICA JAMB INE NOMINA DOOR HEIGHT.25 (6.4) (85.7) 2.25 (57.2)

63 60 Pocket Pivot Preparation April, GA. (1.4) COVERBOX 5/8" (15.9) STOP HEIGHT IF USING COVERBOX 7 GA. (4.5) REINF. TAB PREPARATION: SIZE, DRI AND TAP PER TEMPATE PER TEMPATE PER TEMPATE NOTE: SOME POCKET PIVOTS REQUIRE FRAME FACE DIMENSIONS GREATER THAN 2" (50.8) - KD FRAMES NOT AVAIABE OVER 2" FACE.

64 61 SD - Strike - Double ip November, GA. (2.6) REINFORCING TABS PER TEMPATE PER TEMPATE NOTE: CONTACT FACTORY ON AVAIABIITY WHEN USED WITH C TYPE COMPRESSION ANCHOR KD FRAMES.

65 62 Rescue Hardware Frame November, 2004 EMERGENCY STOP STRIKE SIDE 12 GA. (2.6) REINFORCEMENT PER TEMPATE C PREPARATION: SIZE, DRI AND TAP PER TEMPATE 7-3/4" (196.9) PER TEMPATE DOUBE IP ATCH STRIKE 12 GA. (2.6) REINFORCEMENT C PER TEMPATE COVERBOX 2" (50.8) MINIMUM FACE REQUIRED FOR COVERBOX FOORINE NOTE: CONTACT FACTORY ON AVAIABIITY WHEN USED WITH C TYPE COMPRESSION ANCHOR KD FRAMES.

66 63 Frame Pivots - Top, Bottom - Center Hung December, 2006 COVERBOX TOP PIVOT 7 GA. (4.5) REINF. CENTER HUNG CASED OPENING TOP AND BOTTOM DOUBE ACTING PIVOT PREPARATION: SIZE, DRI AND TAP PER TEMPATE MUDCAP BOTTOM PIVOT 7 GA. (4.5) REINF. COVERBOX TOP PIVOT 7 GA. (4.5) REINF. 1/8" INSET OR EDGE HUNG EDGE HUNG CASED OPENING TOP AND BOTTOM SINGE ACTING PIVOT PREPARATION: SIZE, DRI AND TAP PER TEMPATE MUDCAP BOTTOM PIVOT 7 GA. (4.5) REINF. NOTE: NOT A BOTTOM PIVOTS REQUIRE A FRAME PREP. EDGE HUNG

67 64 Frame Pivots - Top, Intermediate, Bottom - Single Acting April, 2002 COVERBOX TOP PIVOT 7 GA. (4.5) REINF. INTERMEDIATE PIVOT 7 GA. (4.5) REINF. BOTTOM PIVOT 7 GA. (4.5) REINF. MUDCAP

68 65 E1 Strike Reinf. (ANSI A115) 1-1/4" x 4-7/8" April, /4" (31.8) SCREW HOES ARE EXTRUDED TO PROVIDE THREAD DEPTH EQUA TO 12 GA. (2.6) PATE 16 GA. (1.4) REINF. COVER BOX 1-1/16" (27) DEEP STANDARD STRIKE BACKSET 5/16" (7.9) 4-7/8" (123.8) SIZE AND TAP PER ANSI AND " (1016) TO C STANDARD ON 1-3/4" (44.5) DOOR E2 Strike Reinf. (ANSI A115) 1-1/8" x 2-3/4" 1-1/8" (28.6) SCREW HOES ARE EXTRUDED TO PROVIDE THREAD DEPTH EQUA TO 12 GA. (2.6) PATE 16 GA. (1.4) REINF. COVER BOX 1" (25.4) DEEP SIZE AND TAP PER ANSI STANDARD STRIKE BACKSET 3/8" (9.5) 1-3/4" DOOR BACKSET 3/16" 1-3/8" DOOR 2-3/4" (69.9) 40" (1016) TO C STANDARD ON 1-3/4" (44.5) DOOR 40-5/16" TO C STANDARD ON 1-3/8" DOOR

69 66 E1B - Strike Reinf. 1-1/4" x 4-7/8" No ip April, 2002 PER TEMPATE 12 GA. (2.6) REINF. TABS 4-7/8" (123.8) 1-1/4" (31.8) 40" (1016) TO C STANDARD ON 1-3/4" (44.5) DOOR

70 67 E3 Deadlock Strike Reinf. (ANSI/A115) 1-1/8" x 3-1/2" April, /8" (28.6) 16 GA. (1.4) REINF. COVER BOX 1-1/16" (27) DEEP 12 GA. (2.6) REINF. TAB 3-1/2" (88.9) SIZE AND TAP PER ANSI STRIKE BACKSET 3/8" (9.5) 48" (1219) TO C STANDARD ON 1-3/4" (44.5) DOOR E4 Deadlock Strike Reinf. (ANSI/A115) 1-1/8" x 2-3/4" No ip 1-1/8" (28.6) SCREW HOES ARE EXTRUDED TO PROVIDE THREAD DEPTH EQUA TO 12 GA. (2.6) PATE 16 GA. (1.4) REINF. COVER BOX 1" (25.4) DEEP SIZE AND TAP PER ANSI STRIKE BACKSET 3/8" (9.5) 2-3/4" (69.9) 48" (1219) TO C STANDARD ON 1-3/4" (44.5) DOOR

71 68 EJ2 - Jamb ock 2" (50.8) Face April, 2002 PER TEMPATE 2" (50.8) MIN. FACE 3-1/16" (77.8) MIN. FACE ON DRYWA FRAME PER TEMPATE PER TEMPATE REINF. TABS PER TEMPATE C PER TEMPATE 40" (1016)

72 69 EJ4, EJ8, EJ12 - Jamb ock April, 2002 PER TEMPATE COVERPATE PER TEMPATE CUTOUTS PER TEMPATE C STRIKE 40" (1016) 4" (101.6) STANDARD 8" (203.2) STANDARD 12" (304.8) STANDARD

73 70 E30 - Strike - Pocket ock July, GA. (4.5) REINF. TABS PER TEMPATE C PER TEMPATE 40" (1016)

74 71 MAG - Magnetic ock July, 2003 PER TEMPATE REINF. TABS PER TEMPATE PER TEMPATE

75 72 E5 Rim Vertical Rod Surface Strike Reinf. April, 2002 E5 REINFORCING IS OCATED ON CENTERINE OF HEAD FOR PAIR FRAMES AND ADJACENT TO STRIKE JAMB ON SINGE SWING FRAMES. 12 GA. (2.6) 10" (254) 1-3/4" (44.5) DOOR C 12 GA. (2.6) REINF. WEDED TO INSIDE OF SOFFIT TIGHT TO DOOR RABBET STOP G20 Vertical Rod Exit Mortise Strike Preparation DOOR RABBET G20 PREPARED FOR MORTISE STRIKES PER TEMPATE OF HARDWARE MANUFACTURER HEADS SPECIFY EXIT DEVICE AND STRIKE BEING USED WHEN ORDERING

76 73 E8 Rim Exit Reinforcement April, GA. (2.6) 12 GA. (2.6) REINF. WEDED TO INSIDE OF SOFFIT TIGHT TO DOOR RABBET STOP DOOR 1-1/4" (31.8) * 8" (203.2) 41" (1041.4) TO STANDARD C * THE REINFORCEMENT WIDTH WI BE EQUA TO THE SOFFIT WIDTH WHEN ESS THAN 1-1/4" (31.8). CUSTOMER SHOUD VERIFY HARDWARE COMPATIBIITY BEFORE ORDERING NARROW SOFFITS.

77 74 E9 Electric Strikes April, GA. (1.4) REMOVABE COVER BOX CONFIGURATION OF CUTOUT VARIES PER HARDWARE MFG. TEMPATE 12 GA. (2.6) REINF. TAB SPECIFY STRIKE BEING USED WHEN ORDERING C STRIKE 7/8" (22.2) DIA. KNOCKOUT FOR EECTRIC CONNECTOR VERTICA OCATION OF EECTRIC STRIKE WI VARY WITH THE HARDWARE MANUFACTURER, WHEN ORDERING FRAMES PREPARED FOR AN EECTRIC STRIKE, SPECIFY THE TYPE OF OCK BEING USED AONG WITH CENTERINE DIMENSION REQUIRED OF THE OCK. NOTE: FIRE RATED FRAMES INCORPORATING AN EECTRIC STRIKE WITH A COVERBOX, REQUIRE THAT THE WA BOARD PENETRATE THE THROAT OF THE FRAME BY 1/2" (12.7) MINIMUM. EECTRIC STRIKE MUST BE ISTED FOR USE WITH FIRE RATED OPENINGS.

78 75 Conduit - Coverbox Clearance Dimensions September, /8" (28.6) OR 7/8" (22.2) DIA. KNOCKOUT FACE RABBET C REMOVABE COVER END VIEW OF FRAME AND COVERBOX AS REQUIRED C DEPTH C COVERBOX WIDTH 1/2" CONDUIT CONNECTORS ARE FOR 7/8 KNOCKOUT / 1-1/8 HIGH COVERBOX 3/4" CONDUIT CONNECTORS ARE FOR 1-1/8" KNOCKOUT / 1-1/2" HIGH COVERBOX 1/2" (12.7) DOUBE KNOCKOUT FOR 1/2" AND 3/4" CONDUIT CONNECTORS ARE FOR THE 1-1/2" HIGH COVER BOX ONY 1-1/8" HIGH COVERBOX HAS 7/8" KNOCKOUT ONY FOR 1/2" CONDUIT CONNECTOR 1/2" (12.7) CONDUIT CONNECTOR BY OTHERS SIDE VIEW OF COVERBOX 1/2" (12.7) CONDUIT CONNECTOR OCKNUT BY OTHERS 3/4" (19.1) 1-1/8" (28.6)* OCKNUT * 1-1/2" (38.1) FOR 3/4" CONDUIT CONNECTOR MINIMUM INSIDE DEPTH DIMENSION REQUIRED TO ACCOMODATE THE OCKNUT.

79 76 Conduit Preparation (RW-3) March, 2013 OCK SIDE HEAD MUION 6.00" " TOP 6.00" " 1/2" EMT CONDUIT FACTORY INSTAED WHEN REQUESTED (MUION ONY) REQUIRED FOR POWER TRANSFER AND EECTRIC STRIKES JAMB MUION

80 77 E10 Standard Mtg. 14 ga. Closer Reinforcement January, GA. (1.9) 7" (177.8) 1-3/4" (44.5) 10" (254) DOOR HINGE SIDE E11 Parallel Arm Mtg. 14 ga. Closer Reinf. 14 GA. (1.9) 20" (508) DOOR 1-1/4" (31.8) HINGE SIDE 14 GA. (1.9) REINF. WEDED TO INSIDE OF SOFFIT TIGHT TO DOOR RABBET STOP NOTE: WHEN SOFFIT WIDTH IS ESS THAN 1" - E16 WI BE USED

81 78 E12 Top Jamb Mtg. 14 ga. Closer Reinf. November, GA. (1.9) 1-3/4" (44.5) 2" (50.8) 2-3/4" (69.9) DOOR 16" (406.4) HINGE SIDE

82 79 E13 Corner Bkt. Mtg. 14 ga. Closer Reinf. January, GA. (1.9) 8" (203.2) HINGE SIDE 1-1/4" (31.8) DOOR 8" (203.2) 14 GA. (1.9) REINF. WEDED TO INSIDE OF SOFFIT TIGHT TO DOOR RABBET STOP Double Egress Frame Closer Reinforcements E PARAE ARM MOUNTING GA. (1.9) 20" (508) ONG REGUAR TOP JAMB E REGUAR MOUNTING GA. (1.9) 10" (254) ONG E TOP JAMB MOUNTING GA. (1.9) 16" (406.4) ONG E17A FU SEEVE GA. (1.9) REGUAR, TOP JAMB 16" (406.4) ONG PARAE ARM MOUNTINGS E HAF SEEVE GA. (1.9) REGUAR AND 16" (406.4) ONG PARAE ARM MOUNTINGS

83 80 E15 Closer Reinf. October, GA. (1.9) 1/2 (12.7) 1-3/4" (44.45) 24 (609.6) DOOR HINGE SIDE E16 Double Parallel Arm 14 ga. Closer Reinf. 14 GA. (1.9) ADDITIONA REINF. ADDED WHEN SOFFIT IS UNDER 2" (50.8) IN WIDTH 1-1/4" (31.8) 14 GA. (1.9) 20" (508) 20" (508) DOOR VARIES PER SOFFIT WIDTH UP TO 1-5/8" (41.3) HINGE SIDE 14 GA. (1.9) ADDITIONA REINF. WEDED TO INSIDE OF SOFFIT TIGHT TO DOOR RABBET STOP

84 81 E17 14 ga. Full Sleeve Closer Reinforcement April, GA. (1.9) 14 GA. (1.9) 1-3/4 (44.5) 1-3/4 (44.5) 1-3/4 (44.5) 2-3/8 (60.3) 1 (25.4) MIN. 1 (25.4) MIN. 16 (406.4) 16 (406.4) HINGE JAMB INE NOTE: SPECIA PROFIE REINFORCEMENT REQUIRED WHEN COSER IS MOUNTED TO FRAME FACE GREATER THAN 2" E18 14 ga. Formed Half Sleeve Closer Reinf. 14 GA. (1.9) 1-15/16 (49.2) FOR 1-3/4 (44.5) DOOR OR 1-9/16 (39.7) FOR 1-3/8 (34.9) DOOR 16 (406.4) 1-3/4 (44.5) 5/8 (15.9) 1-3/8 (34.9) NOTE 1 3/4 (19.1) NOTE 2 DOOR HINGE SIDE NOTE: 1) 1-1/2 (38.1) MINIMUM SOFFIT REQ D 2) 1 (25.4) MINIMUM SOFFIT REQ D NOTE: SPECIA PROFIE REINFORCEMENT REQUIRED WHEN COSER IS MOUNTED TO FRAME FACE GREATER THAN 2

85 82 EPT - Electronic Power Transfer May, 2011 TOP HINGE * PER TEMPATE PER TEMPATE 12 GA. (2.6) REINFORCING TABS PER TEMPATE * OCATION PER TEMPATE. IF NO OCATION ON TEMPATE, THEN OCATION MUST BE SPECIFIED WITH ORDER. THE QUANTITY OF HINGES MAY REQUIRE COORDINATION OF OCATION WITH DOOR, (EX. 4 HINGES ON A 7'0"). WOOD DOORS MAY REQUIRE OTHER OCATIONS

86 83 G21 - G22 Removable Hardware Mullion April, 2002 MUION TOP BRACKET MOUNTING SCREWS TO BE DRIED AND TAPPED IN FIED BY HARDWARE INSTAER. 5/8" (15.9) C.R.S. FIER BOCK IS FURNISHED WHEN SOFFIT WIDTH IS TOO NARROW TO APPY HARDWARE TO SOFFIT G21 PATE REINFORCEMENT USED WHEN SOFFIT IS 3" (76.2) WIDE OR GREATER. G22 PATE REINFORCEMENT USED WHEN SOFFIT IS ESS THAN 3" (76.2). G21 12 GA. (2.6) G22 PUG WEDED ONY DOOR HARDWARE MUION ASSEMBY DOOR WEDED H3A - H3B Surface Bolt Preparation H3A-12 GA. (2.6) H3B-12 GA. (2.6) 10" (254) 1-3/4" (44.5) 10" (254) DOOR SIDE 1-3/4" (44.5) DOOR H3B SOFFIT PREP. 12 GA. (2.6) REINF. WEDED TO INSIDE OF SOFFIT TIGHT TO DOOR RABBET STOP H3A FACE PREP. 12 GA. (2.6) REINF. WEDED TO INSIDE OF FRAME FACE HEAD AND REINFORCEMENT C OF DOORS NOTE: WHEN ORDERING SPECIFY EITHER H3A OR H3B REINFORCING

87 84 G24 Coordinator Reinforcement October, GA. (2.6) 2" (51) 1-3/8" (34.9) 10" (254) DOOR C OF DOORS 12 GA. (2.6) REINF. WEDED TO INSIDE OF FRAME FACE. C - Closer Reinforcement Per Template C OF PAIR 14 GA. (1.9) *PER TEMPATE *PER TEMPATE DOOR HINGE SIDE * SPECIFY MANUFACTURER AND MODE NUMBER WHEN ORDERING ADVISE POWER SOURCE OCATION IF REQUIRED

88 85 Grout Hole September, GA. (2.6) REINF. PATE 1-3/8" (35) DIA. HOE IN REINF. PATE RABBET PREPARATION (DOOR RABBET STANDARD) 12 GA. (2.6) REINF. PATE 1-3/8" (35) DIA. HOE IN REINF. PATE FIER PATE SAME GAUGE AS FRAME. SHIPPED OOSE. 1-3/8" X 1-3/8" (35 X 35) FACE PREPARATION (DOOR FACE STANDARD) FIER PATE SAME GAUGE AS FRAME. SHIPPED OOSE. 1-3/8" X 1-3/8" (35 X 35)

89 86 H1 Flush Bolt Reinforcement April, GA. (2.6) 1-1/4" (31.8) 8" (203.2) DOOR C OF OPENING AND REINFORCEMENT C 12 GA. (2.6) REINF. WEDED IN CENTER OF DOOR RABBET H2 Flush Bolt Prep. and Reinf. (ANSI) 12 GA. (2.6) 16 GA. (1.4) REINF. COVER BOX 1-1/16" (27) DEEP DOOR 15/16" (23.8) INACTIVE DOOR C CUTOUT C OF DOORS 13/16" (20.6) 15/32" (11.9) BACKSET SIZE AND TAP PER ANSI /4" (57.2)

90 87 H4 Auto Flush Bolt April, 2002 PREPARATION FOR AUTOMATIC FUSH BOT IS PER HARDWARE MANUFACTURER S TEMPATE. PEASE SPECIFY MANUFACTURER AND MODE NUMBER WHEN ORDERING. ABEED IF HARDWARE IS APPROVED AND PREPPED TO TEMPATE. H5 Non-handed Flush Bolt 3-7/8" (98.4) 12 GA. (2.6) REINF. 15/16" (23.8) NOTE: STRIKE PATE INSTAED FIER PATE MAY BE PURCHASED SEPARATEY IN PACKAGES OF 50 PIECES WITH SCREWS. C OF DOORS 5/8" (15.9) C 7/8" (22.2) 1-1/8" (28.6) C C 3-1/4" (82.6) 16 GA. (1.4) GAV. FIER PATE PART #CF HEAD C' SUNK FOR #8-32 X 5/8" (15.9) FAT HEAD HARDWARE SCREW 16 GA. (1.4) GAV. FIER PATE PART #CF001257

91 88 Electric Magnetic Door Position Switch April, 2002 #8 PAN HEAD SCREW. 16 GA. (1.4) GROUT GUARD COVERBOX ENDS SPOT WEDED OVER PREPARATION. EECTRICA CONDUIT KNOCKOUT AS REQUIRED. CUTOUT SIZE AND OCATION PER HARDWARE TEMPATE 12 GA. (2.6) REINFORCING TAB. NOTE: JUNCTION BOXES ARE NOT CAUKED AT THE FACTORY. TO BE FIED CAUKED BY INSTAATION CONTRACTOR.

92 89 Electric Fully-Concealed Door Position Switch April, 2002 #8 PAN HEAD SCREW. 16 GA. (1.4) GROUT GUARD COVERBOX SPOT WEDED OVER PREPARATION EECTRICA CONDUIT KNOCKOUT AS REQUIRED CUTOUT SIZE AND OCATION PER HARDWARE TEMPATE 12 GA. (2.6) REINFORCING TAB NOTE: JUNCTION BOXES ARE NOT CAUKED AT THE FACTORY. TO BE FIED CAUKED BY INSTAATION CONTRACTOR.

93 90 Cabinet Jamb Frame April, 2002 DOOR OPENING ROUGH OPENING NOT U.. ISTED S.M.W. JAMB SECTION BUCKS SHIP OOSE SQUARE BUTT END FIED ASSEMBED WITH SCREWS OR WEDED DOOR OPENING ROUGH OPENING 1-7/8" (47.6) MACH SCREW #8 X 1/2" PAN HEAD 7/8" (22.2) 1" (25.4) ROUGH OPENING DETERMINES THE ENGTH OF THE BUCK EGS 1-3/4" (44.5)

94 91 Rough Buck Frame 2-1/2" (63.5) MIN. TYP. 3" (76.2) MAX. TYP. February, /2" (63.5) MIN. 3" (76.2) MAX. DOOR OPENING U.. ISTED ROUGH BUCK FRAMES BUCKS SHIPPED OOSE SQUARE BUTT END. FUY PREPARED FOR INSTAATION WITH MOUNTING HOES. ROUGH OPENING DOOR OPENING ROUGH OPENING 1/4-20 NC X 1-1/4" FAT HEAD MACH SCREW FINISH BUCK 16 GA. (1.4) OR 14 GA. (1.9) HINGE OR STRIKE REINF. 2" (50.8) 2" (50.8) 2" (50.8) 2" (50.8) #8 x 1/2" PAN HEAD MACH SCREW CORNER DETAI CORNER IS NOTCHED FOR FIED INSTAATION FINISH BUCK CAN NOT BE WEDED PRIOR TO INSTAATION. 12 GA. (2.6) REINF. SUB-CHANNE U.. FRAME ONY SUB-BUCK 14 GA. (1.9) ONY FOR ABE NOTE: ABE FRAMES FURNISHED WITH ATTACHING SCREWS AND BOTS FOR ASSEMBY

95 92 Curriseal Frame Flush KD - WM - WG September, /8" (54.0) VARIES 1-9/16" (39.7) OR 1-15/16" (49.2) CURRISEA ACTUA SIZE COOR: DARK BROWN WM/WG 2-5/8" (66.7) ONY WG 5/8" (15.9) ONY 1" (25.4) 1-1/4" (31.8) 1-1/2" (38.1) 1-3/4" (44.5) 2" (50.8) 1-3/4" DOOR (44.5) 1/4" (6.3) * 1/2" (12.7) 1/8" (3.2) K.D. M TYPE FUSH GAUGE - 18 GA. (1.2), 16 GA. (2.4), 14 GA. (1.9) JAMB DEPTHS: DOUBE RABBET (WM) 5-1/4" (133.4) - 14" (355.6) (1/8" (3.2) INCREMENTS) SINGE RABBET (WG) 4-1/8" (104.8) - 14" (355.6) (1/8" (3.2) INCREMENTS) AVAIABE WITH 4" (101.6) FACE HEADS DOUBE RABBET AVAIABE IN COMMUNICATING FRAMES WITH A 6-1/2" (165.1) MIN. JAMB DEPTH HARDWARE RESTRICTIONS NOT RECOMMENDED - COSERS WITH REMOVABE STOPS - VERTICA ROD DEVICES WITH STRIKES MORTISED IN THE STOP - STOP ACTIVATED VERTICA ROD DEVICES NOTE: SOFFIT MOUNTED SURFACE HARDWARE MAY REQUIRE +_ 1/8" (3.2) ADJUSTMENT OF MOUNTING HOES TO ACCOMODATE WEATHERSTRIP AND ENSURE NORMA DOOR OPERATION. KD CORNER * 5-3/4" (146.1) JAMB DEPTH AVAIABE WITH 7/16" (11.1) RETURNS TO PROVIDE A 4-7/8" (123.8) THROAT OPENING CURRISEA FRAME IS DESIGNED FOR USE WITH THE CURRISEA ONY

96 93 Curriseal Frame KD Drywall - WC - WCG September, /8" (54.0) VARIES 1-9/16" (39.7) OR 1-15/16" (49.2) CURRISEA ACTUA SIZE COOR: DARK BROWN WC/WCG 2-5/8" (66.7) ONY 5/8" (15.9) ONY 1-1/2" (38.1) 1-3/4" (44.5) 2" (50.8) 3/8" (9.5) 1-3/4" DOOR (44.5) 1/2" (12.7) 1/4" (6.3) 1/8" (3.2) K.D. C TYPE DRYWA GAUGE - 18 GA. (1.2), 16 GA. (2.4), 14 GA. (1.9) JAMB DEPTHS: DOUBE RABBET (WC) 5-1/4" (133.4) - 14" (355.6) (1/8" (3.2) INCREMENTS) SINGE RABBET (WCG) 4-1/8" (104.8) - 14" (355.6) (1/8" (3.2) INCREMENTS) DOUBE RABBET AVAIABE IN COMMUNICATING FRAMES WITH A 6-1/2" (165.1) MIN. JAMB DEPTH HARDWARE RESTRICTIONS NOT RECOMMENDED - COSERS WITH REMOVABE STOPS - VERTICA ROD DEVICES WITH STRIKES MORTISED IN THE STOP - STOP ACTIVATED VERTICA ROD DEVICES NOTE: SOFFIT MOUNTED SURFACE HARDWARE MAY REQUIRE +_ 1/8" (3.2) ADJUSTMENT OF MOUNTING HOES TO ACCOMODATE WEATHERSTRIP AND ENSURE NORMA DOOR OPERATION. KD CORNER CURRISEA FRAME IS DESIGNED FOR USE WITH THE CURRISEA ONY

97 94 Notes January, 2007

98 95 Notes January, 2007

99 96 Communicating Frame April, 2002 NOTE: U.. AND W.H.I. ABEED FRAMES MAY BE PROVIDED WITH COMPRESSION TYPE ANCHORING SYSTEM. M PROFIE FUSH K.D. C & CM PROFIE DRYWA EQUA RABBET 1-15/16" (49.2) FOR 1-3/4" (44.5) DOORS 4-7/8" (117.5) THRU 14" (355.6) JAMB DEPTH EQUA RABBET 1-15/16" (49.2) FOR 1-3/4" (44.5) DOORS 4-7/8" (117.5) THRU 14" (355.6) JAMB DEPTH UNEQUA RABBET 1-15/16" (49.2) X 1-9/16" (39.7) FOR 1-3/4" (44.5) X 1-3/8" (34.9) DOORS 4-1/2" (114.3) THRU 14" (355.6) JAMB DEPTH UNEQUA RABBET 1-15/16" (49.2) X 1-9/16" (39.7) FOR 1-3/4" (44.5) X 1-3/8" (34.9) DOORS 4-1/2" (114.3) THRU 14" (355.6) JAMB DEPTH EQUA RABBET 1-9/16" (39.7) FOR 1-3/8" (34.9) DOORS 4-7/8" (117.5) THRU 14" (355.6) JAMB DEPTH EQUA RABBET 1-9/16" (39.7) FOR 1-3/8" (34.9) DOORS 4-7/8" (117.5) THRU 14" (355.6) JAMB DEPTH

100 97 Pocket Door Frame - Standard 1-3/8" or 1-3/4" Door Single March, " (50.8) FINISH OPENING ** 2" (50.8) TRACK HARDWARE & REINFORCEMENT PROVIDED BY OTHERS 1 2" (50.8) * NOMINA DOOR OPENING HEIGHT 5/8" (15.9) 5/8" (15.9) DOOR * NOMINA DOOR OPENING HEIGHT VERIFY HARDWARE ADAPTABIITY FRAME MUST BE INSTAED AND HARDWARE TRACK MUST BE HUNG PRIOR TO FINISH WA STUDS BEING SET. AVAIABE IN 18 GA. (1.2) AND 16 GA. (1.4) STEE. 1/2" (12.7) 2" (50.8) 2 5/8" (15.9) 2" POCKET (50.8) FINISH OPENING WIDTH ** EQUA 1-3/4" (44.5) DOOR 3 2" (50.8) DOOR POCKET 1" (25.4) 1/2" (12.7) 4" (101.6) MIN. 12" (304.8) MAX. 1/2" (12.7) NOTE: 1-3/8" (34.9) DOOR FRAME HAS 1-5/8" (41.3) POCKET EQUA 1/2" (12.7) ANCHOR P110 USED FOR META STUD OR WOOD STUD WA 4-1/4" (107.9) 1" (25.4) VARIES WITH JAMB DEPTH & STUD SIZE. SPECIFY STUD SIZE WHEN ORDERING. ** * FRAME FINISHED OPENING WIDTH SHOUD BE ORDERED 1" ESS THAN DESIRED NET DOOR SIZE. EXAMPE: A 3'0" (914.4) POCKET FRAME WI HAVE FINISH OPENING WIDTH OF 2'11" (889). THIS AOWS THE USE OF STANDARD DOOR WIDTHS. FINISH OPENING HEIGHT IS NOMINA DOOR HEIGHT USING CURRIES STANDARD DOOR UNDERCUT.

101 98 Pocket Door Frame-Saw Mitered-Welded for 1-3/4" or 1-3/8" Doors March, PC 2 PM A A 1. MITER HEAD AND JAMB AT CAMP AND TACK WED AT BACKBEND AND FACE. 3. CONTINUOUS WED INSIDE SEAM. 4. GRIND AND FINISH OUTSIDE SURFACES. B B C C SPIT HEAD AND HINGE JAMB B A C STRIKE JAMB FOOR ANCHOR P165 FOOR ANCHOR WI BE WEDED TO FACES OF FRAME WHEN FACTORY WEDED. MUST BE ATTACHED TO FRAME FACES WHEN FRAME IS WEDED BY OTHERS.

102 99 Stainless Steel Slip-On Type Spats September, 2013 NOTE: SPATS ARE ABEED UP TO A HEIGHT OF 8" (203.2) STAINESS STEE SIP-ON SPAT STANDARD PROFIE IS MANUFACTURED TO FIT OVER JAMB PROFIE. SPECIFY JAMB PROFIE WHEN ORDERING 4" (101.6) STANDARD 18 GA. (1.1) #304 STAINESS STEE #4 SATIN GRAIN FINISH 4" (101.6) STANDARD HOSPITA TYPE SPAT STANDARD PROFIE IS MANUFACTURED TO FIT OVER JAMB BEOW STOP. SPECIFY JAMB PROFIE WHEN ORDERING 18 GA. (1.1) #304 STAINESS STEE #4 SATIN GRAIN FINISH NOTE: HOSPITA TYPE SPATS ARE ABEED UP TO A HEIGHT OF 6" (152.4)

103 100 Hospital Stop April, 2002 ANCHOR PART NUMBER: P0079 FIER & BACKING PATE USED ON FRAMES NOT REQUIRING A FOOT CIP OR FRAMES THAT HAVE SOME OTHER BASE ANCHORING METHOD. NOTE: FOOTCIP REQUIRED FOR ABE ANCHOR PART NUMBER: P0077 FIER & COMBINATION BACKING PATE-FOOT CIP USED ON FRAMES REQUIRING A FOOT CIP. CHOOSE EITHER P0077 OR P0079 BACKING PATE. WED BACKING PATE BEHIND CUTOUT. WED FIER INTO CUTOUT, GRIND, FI AND FINISH SMOOTH. VARIES 4" (101.6) STANDARD STOP CUT AWAY ON 45 ANGE TO RECEIVE FIER 4" (101.6) STANDARD FROM FACTORY * FIER SIZES AVAIABE UP TO 9" (228.6) HIGH 45 CUT HEIGHTS AVAIABE UP TO 9" (228.6) HIGH * 6" (152.4) HIGH MAXIMUM ON FIRE RATED FRAMES FACTORY INSTAED OR BY SECOND OCATION SHOP

104 101 Thermal Break Frame KD Flush Profile December, GA. (1.9) AND 16 GA. (1.4) GAVANEAED STEE 5/8 (15.9) HIGH STOP ONY KD ONY (FACE WEDED ONY) MAXIMUM KD ENGTH JAMB, 116 HEAD PUNCH FOR SIENCERS NOT AVAIABE ANCHOR OPTIONS: MASONRY T WIRE ANCHOR SPIT BASE ANCHOR SPIT WOODSTUD ANCHOR PIPE SPACER ANCHOR 2 (50.8) OR 4 (101.6) FACE HEAD 5-3/4 (146.1) THRU 12-3/4 (323.9) JAMB DEPTH DOOR RABBET THERMA BREAK DOOR RABBET 2 (50.8) FACE THERMA BREAK

105 102 Thermal Break Frame CCW Stick Components December, GA. (1.4) AND 14 GA. (1.9) GAVANEAED STEE ONY 5/8 (15.9) HIGH STOPS ONY BUTT END JOINTS ONY NOT ABEED MUION - 16 GA. (1.4) AND 14 GA. (1.9) 2 (50.8) FACE ONY. PUNCH FOR SIENCERS NOT AVAIABE. 5-3/4 (146.1) THRU 12-3/4 (323.9) JAMB DEPTH DOOR RABBET 2 (50.8) FACE THERMA BREAK DOOR RABBET 2 (50.8) ONY THERMA BREAK

106 103 CCW - Drip Cap CCW '6-5/8" engths March, '6-5/8" (3216.3) 1" (25.4) DRIP CAP 45 C.C.W /4" (19) 16 GA. (1.4) GAVANEA Mullion Construction ORDER CODE: OM

107 104 Removable Vertical Mullion/Bracket August, 2003 ANCHOR PART NUMBER: P0090 MUION BRACKET IS USED AT THE TOP AND BOTTOM OF FRAME * * ATTACH MUION BRACKET TO FRAME NOTCH MUION FACE TO AOW DIMENSION D TO PASS THRU. SIDE MUION IN PACE DIM. B = JAMB DEPTH - FRAME GAUGE THICKNESS DIM. D = DETERMINED BY FACE DIMENSION EQUA TO FACE DIM. MINUS 1/4" (6.4) ARC WED 2 PACES MINIMUM 2" (50.8) D 1" (25.4) DRI 3/16" (4.8) 2 HOES TAP SCREWS INSTAED DIM B * NOTE: THE MUION WI BE REMOVABE FROM THE FACE OPPOSITE THE DOOR RABBET.

108 105 Removable Horizontal Mullion/Bracket July, 2014 NOTE: USED WITH REMOVABE TRANSOM PANE.

109 106 Splice Connection Head or Jamb April, 2002 ANCHOR PART NUMBER: P GA. (1.9) SPICING REINF. 12" (304.8) 1. FIT SPICING SEEVE REINF. HAFWAY INTO ONE SIDE AND TACK WED IN PACE. 2. SIP OTHER SIDE OVER SPICING SEEVE REINF. AND AIGN SEAMS FOR STRAIGHTNESS. 3. TACK WED SPICING SEEVE REINF. INSIDE AND TACK WED OUTSIDE SEAM AT BOTH FACES. 4. CONTINUOUS WED SEAM - GRIND AND FINISH SMOOTH. Field Splice Connection with Bracket ANCHOR PART NUMBER: P GA. (2.6) FIED SPICING SEEVE ARC WED INSIDE ARC WED INSIDE 3" (76.2) FIED SPICE WITH BRACKET FIED WED & FASTEN WITH SCREWS NOTES FOR ABEING PURPOSES: 1) NOTCH SOFFIT OF ADJOINING PIECE. 2) ARC WED SPICING SEEVE BRACKET TO MUION. 3) FU WED FACES OF BOTH PIECES TOGETHER, OR ATTACH WITH 3 #10 SCREWS THROUGH FACE INTO FIED SPICING SEEVE BRACKET.

110 107 KD Double Egress Frame Standards May, 2010 HANDING M - FUSH SERIES KD C - DRYWA KD NOT AVAIABE HR RH H RHR DOUBE RIGHT HAND SWING (STANDARD) * 1/2" (12.7) THROAT OPENING 2-5/8" (79.4) 1 JAMB EQUA 4-3/4" (120.7) MIN. 14" (355.6) MAX. 1-15/16" (49.2) * 1/2" (12.7) EQUA 1-3/8" (34.9) 5/8" (15.9) 1/2" (12.7) 2" (50.8) THROAT OPENING FINISH OPENING WIDTH * * 1/2" (12.7) 3/32" (.094) C HEAD 3 MEETING EDGE 3/16" (.188) 2" (50.8) 2 HEAD 2-5/8" (79.4) 5/8" (15.9) SOFFIT STOP IS HED BACK 3/32" TO PROVIDE PROPER DOOR CEARANCE * 4" (101.6) MIN. 14" (355.6) MAX. 5-3/4" (146.1) JAMB DEPTH HAS 7/16" (11.1) RETURN 18, 16, 14 GA. 12 GA. 1/2" RETURN NO KD

111 108 S.B.E. Double Egress Frame Corner Joints November, 2004 RETURN FIER VERTICA BUTT JOINT (STANDARD) WEDED & GROUND SMOOTH WED RETURN FIER RETURN FIER HORIZONTA BUTT JOINT (OPTIONA) WEDED & GROUND SMOOTH

112 109 CCW - Open Back Rail - 10'6-5/8" engths November, '6-5/8" (3216.3) OPEN BACK RAI HINGE JAMB 6'8" (2032) OCATION 3 HINGES C.C.W. 24 7'0" (2133.6) OCATION 3 HINGES C.C.W. 25 7'2" (2184.4) OCATION 3 HINGES C.C.W. 39 OPEN BACK RAI HINGE JAMB 7'10" (2387.6) OCATION 4 HINGES C.C.W. 62 8'0" (2438.4) OCATION 4 HINGES C.C.W. 63 9'0" (2743.2) OCATION 4 HINGES C.C.W '0" (3048) OCATION 4 HINGES C.C.W. 120 OPEN BACK RAI STRIKE JAMB C.C.W. 26 FOR 1-3/4" (44.5) DOORS A STRIKE OCATIONS 40" (1016) C IF PUNCHED - SIENCERS ARE REQUIRED WHEN ORDERING CCW 26 STRIKE JAMB SPECIFY DOOR HEIGHT NOTE: ANCHORS ARE NOT INCUDED WITH CCW MATERIA. CCW MATERIA MAY BE ORDERED CUT TO ENGTH - EXACT ENGTH - WITH S.M.O. OR S.B.E. CORNER CONFIGURATION. CUSTOM PROFIES AVAIABE. 12 GA. FRAMES ARE CCW. 5-3/4 JAMB DEPTH HAS 1/2" RETURNS.

113 110 CCW - Mullion Closed Section - 10'6-5/8" engths November, '6-5/8" (3216.3) MUION - COSED SECTION HINGE JAMB 6'8" (2032) OCATION 3 HINGES C.C.W. 42 7'0" (2133.6) OCATION 3 HINGES C.C.W. 43 7'2" (2184.4) OCATION 3 HINGES C.C.W. 44 MUION - COSED SECTION HINGE JAMB 7'10" (2387.6) OCATION 4 HINGES C.C.W. 81 8'0" (2438.4) OCATION 4 HINGES C.C.W. 82 9'0" (2743.2) OCATION 4 HINGES C.C.W '0" (3048) OCATION 4 HINGES C.C.W. 134 MUION - COSED SECTION STRIKE JAMB FOR 1-3/4" (44.5) DOORS A STRIKE OCATIONS 40" (1016) C IF PUNCHED - SIENCERS ARE REQUIRED WHEN ORDERING CCW 41 STRIKE JAMB SPECIFY DOOR HEIGHT C.C.W GA. FRAMES ARE CCW

114 111 CCW - Mullion Closed Section - 10'6-5/8" engths Communicating Mullion November, '6-5/8" (3216.3) MUION - COSED SECTION COMBINATION RAI A STANDARD DOOR HEIGHTS. DOUBE HINGE, DOUBE STRIKE OR HINGE AND STRIKE COMBINATIONS. 6'8" (2032) OCATION 3 HINGES & STRIKE C.C.W. 45 7'0" (2133.6) OCATION 3 HINGES & STRIKE C.C.W. 46 7'2" (2184.4) OCATION 3 HINGES & STRIKE C.C.W. 47 7'10" (2387.6) OCATION 4 HINGES & STRIKE C.C.W. 83 8'0" (2438.4) OCATION 4 HINGES & STRIKE C.C.W. 84 9'0" (2743.2) OCATION 4 HINGES & STRIKE C.C.W '0" (3048) OCATION OF 4 HINGES & STRIKE C.C.W. 136 DOUBE STRIKE MUION C.C.W. 85 NOTE: WHEN ORDERING CCW 85 SPECIFY DOOR HEIGHT. 6'8" (2032) OCATION 3 (DOUBE HINGES) C.C.W. 86 7'0" (2133.6) OCATION 3 (DOUBE HINGES) C.C.W. 87 7'2" (2184.4) OCATION 3 (DOUBE HINGES) C.C.W. 88 7'10" (2387.6) OCATION 4 (DOUBE HINGES) C.C.W. 89 8'0" (2438.4) OCATION 4 (DOUBE HINGES) C.C.W. 90 9'0" (2743.2) OCATION 4 (DOUBE HINGES) C.C.W '0" (3048) OCATION OF 4 (DOUBE HINGES) C.C.W. 138 NOTE: WHEN ORDERING COMBINATION MUION DOUBE HINGE, DOUBE STRIKE, OR HINGE AND STRIKE, PROVIDE SECTION DETAI OF DOOR RABBET OCATION. EXAMPE 12 GAUGE FRAMES ARE CCW

115 112 CCW Sills - CCW 28, 139, 140, 48, 49, 55-10'6-5/8" engths November, '6-5/8" (3216.3) 4" (101.6) 6" (152.4) 8" (203.2) JAMB DEPTH FU JAMB DEPTH 4" (101.6) FACE OR ESS C.C.W. 28 FU JAMB DEPTH 6" (152.4) FACE OR ESS C.C.W. 139 FU JAMB DEPTH 8" (203.2) FACE OR ESS C.C.W /16" (173) JAMB DEPTH FU JAMB DEPTH 6-13/16" (173) FACE C.C.W. 55 5/8" (15.9) 4" (101.6) 6" (152.4) 8" (203.2) 1-9/16" (39.7) SPECIA 1-9/16" (39.7) THICK C.C.W. 48 5/8" (15.9) 4" (101.6) 6" (152.4) 8" (203.2) 1-15/16" (49.2) SPECIA 1-15/16" (49.2) THICK C.C.W GAUGE FRAMES ARE CCW

116 113 CCW - Plain Mullion CCW 16, 17, 18, 50-10'6-5/8" engths November, '6-5/8" (3216.3) 2" (50.8) FACE JAMB DEPTH PAIN MUION 2" (50.8) FACE C.C.W. 16 4" (101.6) FACE JAMB DEPTH PAIN MUION 4" (101.6) FACE C.C.W. 17 6" (152.4) FACE JAMB DEPTH PAIN MUION 6" (152.4) FACE C.C.W. 18 8" (203.2) FACE JAMB DEPTH PAIN MUION 8" (203.2) FACE C.C.W GAUGE FRAMES ARE CCW

117 114 CCW - Plain Rail CCW 21, 23, 115, '6-5/8" engths November, '6-5/8" (3216.3) 2" (50.8) FACE JAMB DEPTH PAIN RAI 2" (50.8) FACE C.C.W. 21 4" (101.6) FACE JAMB DEPTH PAIN RAI 4" (101.6) FACE C.C.W. 23 6" (152.4) FACE JAMB DEPTH PAIN RAI 6" (152.4) FACE C.C.W " (203.2) FACE JAMB DEPTH PAIN RAI 8" (203.2) FACE C.C.W GAUGE FRAMES ARE CCW

118 115 Sill Reinforcement August, 2003 ANCHOR PART NUMBER: P320 OCATED EVERY 18" OF SI ENGTH WHEN FACE EXCEEDS 5". PROVIDES ADDITIONA SUPPORT TO PROFIE FACE. ONE STIFFENER EVERY 18" OF ENGTH ON FACE DIMENSIONS 5" TO 9" FACE DIMENSIONS 9" THRU 16" MAX. REQUIRE TWO STIFFENERS PER 18" OF ENGTH. 2" (50.8) 1-1/2" (38.1) 12 GA. (2.6)

119 116 CCW - Misc. Rail CCW 19, 27, 22, 29-10'6-5/8" engths November, '6-5/8" (3216.3) CORNER COVER PATE CORNER OR FAT C.C.W. 19 OR FAT JAMB DEPTH FIER PATE WITHOUT STOP C.C.W. 27 JAMB DEPTH FIER PATE WITH STOP C.C.W. 22 JAMB DEPTH HEAD CAP C.C.W. 29 JAMB DEPTH 12 GAUGE FRAMES ARE CCW

120 117 CCW - Misc. Rail CCW 91, 92, 40-10'6-5/8" engths November, '6-5/8" (3216.3) CHANNE HEAD REINF. C.C.W. 91 JAMB DEPTH FU WIDTH HEAD REINF. C.C.W. 92 JAMB DEPTH CASED OPENING PAIN RAI CASED OPENING PAIN RAI 4" (101.6) C.C.W. 40 2" FACE C.C.W. 20 4" FACE JAMB DEPTH 12 GAUGE FRAMES ARE CCW

121 118 CCW - Corners CCW 51, 52, 53, 54-10'6-5/8" engths November, /16" (39.7) 1-15/16" (49.2) JAMB DEPTH JAMB DEPTH 1-15/16" (49.2) 1-9/16" (39.7) 1-9/16" (39.7) JAMB DEPTH 2 WAY CORNER 1-9/16" (39.7) OUTSIDE C.C.W /16" (49.2) 1-15/16" (49.2) JAMB DEPTH 2 WAY CORNER 1-15/16" (49.2) OUTSIDE C.C.W /16" (39.7) 1-9/16" (39.7) 1-9/16" (39.7) 1-15/16" (49.2) 1-15/16" (49.2) JAMB DEPTH JAMB DEPTH 1-15/16" (49.2) 1-15/16" (49.2) 1-9/16" (39.7) 1-9/16" (39.7) 1-9/16" (39.7) JAMB DEPTH 3 WAY CORNER 1-9/16" (39.7) OUTSIDE C.C.W /16" (49.2) 1-9/16" (39.7) JAMB DEPTH 3 WAY CORNER 1-15/16" (49.2) OUTSIDE C.C.W /16" (49.2) 12 GAUGE FRAMES ARE CCW

122 119 CCW - Glass Stop November, /8" (15.9) 18 GA. 1" (25.4) 18 GA. 5/8" (15.9) 16 GA. 1" (25.4) 16 GA. 1" (25.4) 16 GA. 5/8" (15.9) 5/8" (15.9) 3/4" (19) 3/4" (19) 1" (25.4) CCW# HEIGHT X WIDTH DESCRIPTION 93 5/8" (15.9) X 5/8" (15.9) PRIME PAINT - PUNCHED 12" (304.8) ON CENTER 97 5/8" (15.9) X 5/8" (15.9) PRIME PAINT - BANK 101 5/8" (15.9) X 5/8" (15.9) NO PAINT - BANK 105 5/8" (15.9) X 5/8" (15.9) NO PAINT - PUNCHED 12" (304.8) ON CENTER 94 5/8" (15.9) X 1" (25.4) PRIME PAINT - PUNCHED 12" (304.8) ON CENTER 98 5/8" (15.9) X 1" (25.4) PRIME PAINT - BANK 102 5/8" (15.9) X 1" (25.4) NO PAINT - BANK 106 5/8" (15.9) X 1" (25.4) NO PAINT - PUNCHED 12" (304.8) ON CENTER 95 3/4" (19) x 5/8" (15.9) PRIME PAINT - PUNCHED 12" (304.8) ON CENTER 99 3/4" (19) x 5/8" (15.9) PRIME PAINT - BANK 103 3/4" (19) x 5/8" (15.9) NO PAINT - BANK 107 3/4" (19) x 5/8" (15.9) NO PAINT - PUNCHED 12" (304.8) ON CENTER 96 3/4" (19) X 1" (25.4) PRIME PAINT PUNCHED 6" (152.4) ON CENTER 100 3/4" (19) X 1" (25.4) PRIME PAINT - BANK 104 3/4" (19) X 1" (25.4) NO PAINT - BANK 108 3/4" (19) X 1" (25.4) NO PAINT - PUNCHED 6" (152.4) ON CENTER 143 1" (25.4) X 1" (25.4) - PRIME PAINT - PUNCHED 6" (152.4) ON CENTER 9/32" (7.1) GASS STOP IS MANUFACTURED FROM GAVANEAED STEE. PAINT IS CURRIES STANDARD GRAY PRIME. PUNCHING IS FOR OVA HEAD SCREWS SIZE #8. NOTE: HOE PUNCHING ON GASS STOP IS STANDARD 12" (304.8) ON CENTER. IF STOP IS TO BE USED FOR ABE FRAME APPICATIONS YOU MUST SPECIFY ON ORDER THAT HOES ARE TO BE 6" (152.4) ON CENTER. A GASS STOP AND SOFFIT STOP MATERIA COME IN 10'6" (3200.4) ENGTHS STAINESS STEE GASS STOP IS 16 GA. (1.4)

123 120 CCW - Shipping Spreader Bar CCW '6-5/8" engths April, /8" (9.5) 1" (25.4) TACK WED SHIPPING SPREADER BAR TO BOTTOM OF FRAME RABBET INSIDE NOMINA FRAME OPENING. TOP VIEW OOKING DOWN NOTE: CURRIES HOOW META FRAMES HAVE DOUBE SHIPPING SPREADER BARS WEDED ON THE BOTTOM. THE SPREADER BARS MUST BE REMOVED AND A SETTING SPREADER USED FOR FINA INSTAATION. A COD CHISE AND HAMMER ARE RECOMMENDED TOOS TO USE TO REMOVE THESE. THE FRAME INSTAER ASSUMES A RESPONSIBIITY FOR PUMB FRAME INSTAATION.

124 121 Custom Frame Profiles February, 2016 CONTACT FACTORY FOR CAPABIITIES 289 3/4 (19.1) MINIMUM B 3/4 (19.1) MINIMUM 1/2 (12.7) MINIMUM 1/2 (12.7) MINIMUM 1 (25.4) MINIMUM 3/8 (9.5) MINIMUM 1 (25.4) MINIMUM NOTE: FOR 12 GA. (2.6) CONTACT FACTORY F VARIES 1/8 (3.2) 16 GA. (1.4) MINIMUM 5/32 (4) 14 GA. (1.9) MINIMUM VARIES

125 122 Custom Frame Profiles March, /2 (12.7) 1/2 (12.7) RADIUS ONY 16 GA. ONY NOTE THROAT OPENING WHEN ORDERING 1/2 (12.7) MINIMUM 2 (50.8) MAXIMUM MH 3/4 (19.1) MINIMUM 4 MIN. (101.6) 9-3/4 MAX. (247.7) NOT 12 GA. (2.6) 1/8 (3.2) 16 GA. (1.4) 3/16 (4.8) 14 GA. (1.9) I 3/4 (19.1) MINIMUM 1-1/2 (38.1) MINIMUM 4 (101.6) MAXIMUM 1 (25.4) MINIMUM 16 GA. ONY NOTE THROAT OPENING WHEN ORDERING 1/4 (6.4) ONY 3/8 (9.5) MINIMUM 2 (50.8) MAXIMUM 3/4 (19.1) MINIMUM 1/2 (12.7) MINIMUM 2 (50.8) MAXIMUM MIN. (101.6) 9-3/4 MAX. (247.7) 1/2 (12.7) 1 (25.4) MINIMUM 1/2 (12.7) MINIMUM 1/2 (12.7) ONY 1/2 RADIUS 2 (50.8) MINIMUM 4 (101.6) MAXIMUM

126 123 Mercury Thermal Break Frame KD Flush Profile September, 2018 SINGE RABBET: 3-3/4" (95.3) THRU 5-5/8" (142.9) JAMB DEPTH DOUBE RABBET: 5-3/4" (146.1) THRU 14" (355.6) JAMB DEPTH 14 GA. (1.9) AND 16 GA. (1.4) GAVANEAED STEE 5/8 (15.9) HIGH STOP ONY KD, FACE ONY WED, OR FU WED (SOFFIT IS NOT WEDED) MAXIMUM KD ENGTH JAMB, 8 0 HEAD PUNCH FOR SIENCERS NOT AVAIABE ANCHOR OPTIONS: WIRE ANCHOR SPIT BASE ANCHOR SPIT WOODSTUD ANCHOR EXISTING WA ANCHOR NFRC 102 U AND R VAUES STANDARDIZED THERMA TRANSMITTANCE MERCURY FRAME & TRIO-E FUSH DOOR - U VAUE 0.36, R VAUE 2.65 MERCURY FRAME & FRP FUSH DOOR - U VAUE 0.39 MERCURY FRAME & MERCURY FUSH DOOR - U VAUE 0.37 R VAUE 2.53 NFRC 400 AIR INFITRATION (CFM/SQ FT) MERCURY FRAME & TRIO-E FUSH DOOR MERCURY FRAME & FRP FUSH DOOR MERCURY FRAME & MERCURY FUSH DOOR (25.4) THRU 2 (50.8) OR 4 (101.6)FACE THERMA BREAK DOOR RABBET SINGE RABBET: 3-3/4 (95.3) THRU 5-5/8 (142.9) JAMB DEPTH DOUBE RABBET: 5-3/4 (146.1) THRU 14 (355.6) JAMB DEPTH THERMA BREAK PEMKO S44 SHIPS OOSE WITH FRAME, TO BE FIED INSTAED AFTER FINISH PAINT. DOOR RABBET 1 (25.4) THRU 2 (50.8) FACE

127 124 Mercury Thermal Break Frame CCW Stick Components September, GA. (1.4) AND 14 GA. (1.9) GAVANEAED STEE ONY 5/8 (15.9) HIGH STOPS ONY BUTT END JOINTS ONY NOT ABEED MERCURY U VAUE MERCURY R VAUE MUION - 16 GA. (1.4) AND 14 GA. (1.9) PUNCH FOR SIENCERS NOT AVAIABE. THERMA BREAK 5-3/4 (146.1) THRU 14 (355.6) JAMB DEPTH 3-3/4 (95.3) THRU 5-5/8 (142.9) JAMB DEPTH AVAIABE SINGE RABBET THERMA BREAK THERMA BREAK

128 125 Mercury Thermal Break Frame Profiles with Stucco Flange October, 2018 TQU Profiles TRU Profiles A. GAUGE B. MATERIA TQU PROFIE 16 (MAX SIZE 8 0" X 8 0") 14 (MAX SIZE 8 0" X 8 0") COD ROED ASTM A60 GAVANNEAED ASTM G90 GAVANIZED TRU PROFIE 16 (MAX SIZE 8 0" X 8 0") 14 (MAX SIZE 8 0" X 8 0") COD ROED ASTM A60 GAVANNEAED ASTM G90 GAVANIZED C. FINISH PRIME PAINTED PRIME PAINTED D. DEPTH 5-3/4" TO 14" 3-7/8" TO 5-5/8" E. THROAT SINGE RABBET 1-3/16" ESS THAN DEPTH (OUTSWING/INSWING) 1-3/8" ESS THAN DEPTH (STUCCO) F. FACE 1" THRU 4" 1" THRU 4" G. STOP HEIGHT 5/8" 5/8" 1-3/16" ESS THAN DEPTH (OUTSWING/INSWING) 1-3/8" ESS THAN DEPTH (STUCCO) H. CORNER CONDITION KD (WITHOUT TABS) OR SETUP AND WEDED * KD (WITHOUT TABS) OR SETUP AND WEDED * I. OPENING WIDTH SINGE OPENING WIDTH DOUBE 2 0" TO 4 0" 4 0" TO 8 0" 2 0" TO 4 0" 4 0" TO 8 0" J. OPENING HEIGHT 2 0" TO 8 0" 2 0" TO 8 0" K. RABBET 1-15/16" 1-15/16". SOFFIT 1-7/8" MIN. 1-7/8" MIN. M1. M2. BACKBEND BACKBEND (FANGE SIDE) 1/2" 5/8 STD. 1/2 MIN. 1/2" 5/8 STD. 1/2 MIN. N1. FANGE 1/2" STANDARD, 1/2" MIN. 3" MAX. 1/2 STANDARD, 1/2 MIN. 3 MAX. ANCHORS MASONRY EXISTING OPENING WOOD STUD STRAPS ONY SPIT FIXED FOOR ATTACHMENT WIRE MASONRY ANCHOR WEDED IN WEDED IN WEDED IN PEMKO S44 SHIPS OOSE WITH FRAME, TO BE FIED INSTAED AFTER FINISH PAINT. A DIMENSIONS SHOWN ARE STANDARD. FOR VARIATIONS REFER TO THE CHART FOR IMITS. NOTE: SOME OF THESE COMBINATIONS, DUE TO MANUFACTURING CEARANCE, MUST BE MADE IN MUTIPE PIECES. * FUY WEDED THERMAY BROKEN FRAMES WI BE IMITED TO FACE MITER WEDS, HEAD AND JAMB RABBET SEAM WEDS ONY. (Conversion: 1" = 25.4 mm, e.g., 1-3/4" = mm)

129 126 Steel Channel Anchor Installation November, 2014 TWIST 45 TO CEAR THE RETURNS. ROTATE ANCHOR 45 TO CEAR RETURNS. SIDE INTO PROFIE. TWIST THE ANCHOR UPRIGHT. ROTATE THE ANCHOR COCKWISE TO TIGHTEN IN THE PROFIE. ROTATE TO GET THE ANCHOR EGS UNDER THE PROFIE RETURNS.

130 127 Door Silencers October, " (127) 5" (127) 8" (203.2) C SIENCERS 2" (50.8) SIENCERS SINGE DOOR FRAME TOP OF STRIKE CUTOUT PAIR OF DOORS FRAME 10" (254) ADHESIVE TYPE PUNCH TYPE ADHESIVE BACKED SIENCERS FIED APPIED AFTER FINISH PAINTING 17/64" (6.8) DIA. HOE TO ACCEPT PUSH IN TYPE SIENCERS ADHESIVE BACKING 17/64" (6.8) 5/8" (15.9)

131 128 oose Spline Sleeve September, 2003 PART #P (1.4) GA. JAMB DEPTH -5/16" (7.9) 4" (101.6) 16 GA. (1.4) PART #P200 4 SPOT WEDS

132 129 KD Frame Assembly Instructions MASONRY FRAMES, THERMA BREAK, AND CURRISEA FOR MASONRY, META STUD, AND WOOD STD WAS September, 2011 Assembly of Frame #8 SCREW (MS002485) (REQUIRED ON A KD APPICATIONS) Plumbing of Frame Squaring the Frame The installer should use wood spreaders (as described below), a carpenters level (the longer the better), and a full size carpenters square. Set the frame in the desired location. evel head and plumb jambs. Shim under jambs if necessary. HEAD Spreader Typical wood spreader must be square and made from lumber at least 1 thick. ength of spreader equals door opening width at the head. Cut clearance notches for frame stops as shown. Spreader must be nearly as wide as frame depth for accurate installation. JAMB Job Storage Store frames off the ground on wood runners or skids. Do not store directly on the ground. Cover frames with tarpaulin or plastic but do insure that adequate ventilation is provided to eliminate moisture condensation. When frames are to be fully grouted and when plaster or mortar contain "anti-freeze" agents, the inside of the frames should be coated with a bituminous, water-resistant paint by the installation contractor. BRACING FRAMES BEFORE WA CONSTRUCTION FOR KD AND WEDED FRAMES Bracing the frame Brace the frame as shown or shore to a structure above. Brace in the direction of intended wall. Plumb and square jambs. Install vertical brace to support header for openings over 4'0" wide. NOTE ON WEDED FRAMES: Shipping bars should NOT be used as spreader. Remove shipping bar before setting frame. PUMB FRAME DEPTH EVE SQUARE A A SECTION A-A SPREADER Plumbing the frame The contractor should be equipped with a carpenter level, square and spreader. Set the frame in desired location and level the header. Square jambs to header. Shim under jambs if necessary. With frame in place, set spreader and fasten jambs to floor through floor anchors. DOOR OPNG. AT HEADER Spreader Typical wood spreader must be square and fabricated from lumber no less than 1" thick. Correct length is the door opening width between the jambs at the header (i.e., Single Door 3'0" = 36"). Cut clearance notches for frame stops. Spreader must be nearly as wide as frame depth for accurate installation.

133 130 KD Frame Assembly Instructions September, 2011 NEW MASONRY CONSTRUCTION FOR KD AND WEDED FRAMES SPREADER 1. Assemble frame. 2. Set brace and plumb frame. 3. Install anchors. Grout frame in the area of the anchors as block courses are laid up. Frames may also be supplied with anchors welded in place. 4. A second spreader is recommended at the mid point of the door opening to maintain the door opening dimension. 5. Continually check plumb and square as wall progresses. Wire Anchor NOTE: Anchors in frame heads are not required. Existing Masonry Construction 1. Drill (4) 9/16" diameter holes evenly spaced in each jamb for 3/8" expansion shell anchors. Install multipurpose anchor at each 9/16" hole. 2. Assemble 3 frame pieces flat on floor. Install (4) #8 x 1/2" sheet metal screws (included) at corners of head to each jamb (required for Underwriters aboratories fire rating). ocate removable spacing bar at base of frame to maintain proper opening width during installation. 3. Position assembled frame in opening. Plumb and level the frame. Shim frame as required. 4. Anchor frame to wall with 3/8" expansion shell anchors, shimming behind anchors as needed. T Anchor STEE STUD WA CONSTRUCTION WITH FUSH OR RECESS TYPE ANCHORS FOR KD AND WEDED FRAMES HEADER STUD JAMB STUD 90 SPREADER 90 JAMB STUD Elevation 1. Assemble frame. 2. Install anchors. Position anchors in frame through the throat and tap in with a hammer. Frames may also be supplied with anchors welded in place. 3. Square, brace and plumb frame as shown. 4. Set spreader. Attach jambs to floor through floor anchor or floor extension. Install jamb studs to floor and ceiling runners and tightly against frame anchors. 5. Attach studs to frame anchors as shown below. NOTE: Drywall must extend at least 1/2" into frame at fire rated installations. FRAME CHANNE TYPE JAMB STUDS Channel type steel stud Position studs in frame throat and attach to anchors with screws or weld. If using screws, the installer should drill from the back side of the stud, through both the stud and anchor, then attach with (2) screws per anchor location. NOTE: When attaching header stud to jamb studs, be sure the stud is above frame header. This will assure ample room for attaching plaster lath or drywall and will not interfere with installation of hardware attached to frame header. Anchors are not required in frame heads, except fire listed double egress openings.

134 131 KD Frame Assembly Installation WOOD STUD CONSTRUCTION FOR KD AND WEDED FRAMES September, 2011 ANGE BRACES HEADER STUD JAMB STUD FRAME SPREADER WOOD STUDS FOOR RUNNER SPREADER Erect frame Assemble frame. Stand frame up in desired location. Anchor one jamb to floor and set spreader on floor from anchored jamb to loose jamb. Plumb, level, and square frame. Position and anchor second jamb, then brace. NOTE: Drywall must extend at least 1/2" into frame at fire rated installations. 1. Install anchors. Position anchors in frame throat and tap in with a hammer. Frames may also be supplied with anchors welded in place. 2. Set spreader. Attach jambs to floor through floor anchor or floor extension. Install double jamb studs to floor and ceiling runners and header. 3. Bend anchor tabs around stud leaving desired clearance between frame return and stud for inserting finished wall material. 4. Square and nail top anchor to stud on ONE JAMB ONY. Check plumb and square and continue to nail balance of anchors to stud. Repeat for opposite jamb. 5. Anchors are not required in frame heads, except fire listed double egress openings. WOOD STUD CONSTRUCTION (STUDS ERECTED BEFORE FRAME) ROUGH OPENING DIMENSIONS Rough opening Build rough opening. Rough opening dimensions for 2" face frames should be 4-1/4" - 4-1/2" larger than door width and 2-1/4" - 2-1/2" larger than door height. It is recommended that double studs be used at jambs and headers. 1. Assemble frame. 2. Install anchors. Position anchors in frame throat and tap in with a hammer. Frames may also be supplied with anchors welded in place. Base anchors may also be used. If base anchor cannot be used add one anchor per jamb at bottom. 3. Place frame in rough stud opening. 4. Bend anchor tabs around stud leaving desired clearance between frame return and stud for inserting finished wall material. 5. Set spreader and level frame. Shim jambs if necessary. 6. Square and nail top anchor to stud on ONE JAMB ONY. Check plumb and square and continue to nail balance of anchors to stud. Repeat for opposite jamb. 7. Anchors are not required in frame heads, except fire listed double egress openings. FRAME WOOD STUDS 90 SPREADER 90 NOTE: Drywall must extend at least 1/2" into frame at fire rated installations.

135 132 Notes August, 2017

136 133 Security Sidelite Door Construction March, OR 14 GA. FRAMES WITH WEDED CORNERS 6-3/4" MINIMUM DEPTH FEATURES: HINGED SECURITY PANE COSES TO CREATE A VISUA BARRIER GASS POCKETS AVAIABE FOR UP TO 1 THICK GASS PREPARED FOR SEF ATCHING DEADBOT TO MEET PROJECT REQUIREMENTS STANDARD 4-1/2 X.134 HINGE PREPARATIONS OPTIONS: AVAIABE WITH MASONRY AND STUD WA ANCHORS FIRE RATING: WARNOCK HERSEY 3/4 HOUR RATING. (1-1/2 HOUR WITH SPECIATY GAZING) USES: CASSROOMS POST OFFICES GOVERNMENT FACIITIES AIRPORTS OPERABE PANE GASS OUTSIDE SECTION INSIDE

137 134 Transom Frame Removable Panel Installation April, 2012 HORIZONTA ASTRAGA REQUIRED. PANE - RATED - HONEYCOMB AND MINERA CORE NON-RATED - STEE STIFFENED AND POYSTYRENE 3/8" RETAINER PINS FOR REMOVABE PANES: WEDED TO INSIDE OF HEAD. 6" FROM ENDS 18" MAX O.C. FRAME - 3 HR MAX. RATING 11'4" MAX. HEIGHT 4' MAX. WIDTH SINGE 8' MAX. WIDTH PAIR 16 GAUGE GUIDE CHANNE TOP OF PANE NOTCHED FOR GUIDE CHANNES TAPPED FOR 1/4-20 MS BOTH FACE SHEETS WEDED TO VERTICA END CHANNES, 6" O.C. 1/4" STEE PATE 48" MAX. PANE HEIGHT 16 GAUGE GUIDE (END) CHANNES BOTH SIDES 1/4-20 FHMS (2) HORIZONTA EDGES OF PANE ARE WEDED TO CONTINUOUS CHANNE 1/4" STEE PATE WITH CEAR HOE NOMINA 1-3/4" THICK BOTTOM OF PANE TOP OF PANE 1-9/16" 7/8" JAMB DRI 1/4" AND COUNTERSINK NOTE: PANE AND TRANSOM FRAME REQUIRE SPECIA CONSTRUCTION. MUST BE INDICATED ON BOTH DOOR AND FRAME ORDER. DOOR OPENING 17/32" TO BOTTOM OF PANE & 1/8" CEARANCE TO TOP OF DOOR FROM BOTTOM OF PANE

138 135 Slip-on N Profile Door Frame May, 2018 TABS SOTS HEAD COMPRESSION ANCHOR DRIVER ACCESS HOE JAMB CORNER ASSEMBY N PROFIE INSTA STANDARD WITH NAIER WI BE HOES COMPRESSION IN FACE. ANCHORS AVAIABE AND NAI WITH HOES OR WITHOUT ON BOTH SIDES. COMPRESSION ANCHORS. NM PROFIE WI NOT HAVE COMPRESSION ANCHORS. ANCHORS (WEDED IN ONY) AND NAI HOES NEED TO BE SPECIFIED. COMPRESSION ANCHOR (OPTIONA) * ORDER USING JAMB DEPTH JAMB DEPTH = THROAT DIMENSION +1/8 2 (HEIGHT) SEE CHART THROAT * WIDTH SEE CHART FASTENER ATTCHMENT HOES PUNCHED IN EACH FACE COMPRESSION AN- CHOR OPTIONA SPECIFICATIONS: MAXIMUM SINGE 4 0 (1219) W X 9-0 (2743) H MAXIMUM PAIR 8 0 (2438) W X 9 0 (2743) H (NO DOUBE EGRESS) THROAT 3-3/4 (95) MIN TO 13 (330) MAX 3F ONY. SINGE AND DOUBE RABBET ONY (NO KERF) GAUGE: 16 GA. (1.5) MIN, 14 GA (1.8) MAX MATERIA: COD ROED OR GAVANNEAED STEE ATTACHMENT HOES: HOES ARE OCATED AT 16 MAX SPACING AND 2 MAX FROM ENDS. FIRE ABE NOTES: WOOD TRIM SHA BE APPIED TO FRAME FACES WITH A FIRE ISTED CONTACT ADHESIVE AND /OR FAST CAP 2P-10 ADHESIVE. WOOD TRIM MUST BE HED BACK FROM THE CORNER OF THE FRAME FACE (COSEST TO THE DOOR RABBET) APPROXIMATEY 1/4-3/8.

139 136 Slip-On Hybrid Drywall Door Frame May, MINUTE MAXIMUM RATING (INTERTEK ONY) CORNER CIP TAB SOT HEAD JAMB CORNER ASSEMBY COMPRESSION ANCHOR COMPRESSION ANCHOR THROAT SPECIFICATIONS: MAXIMUM SINGE 4 0 (1219) W X 9-0 (2743) H MAXIMUM PAIR 8 0 (2438) W X 9 0 (2743) H (NO DOUBE EGRESS) THROAT 3-3/4 (95) MIN TO 13 (330) MAX 3F ONY. SINGE AND DOUBE RABBET ONY (NO KERF) GAUGE: 16 GA. (1.5) MIN, 14 GA (1.8) MAX MATERIA: COD ROED OR GAVANNEAED STEE ATTACHMENT HOES: HOES ON THE NO RETURN SIDE OCATED AT 16 MAX SPACING AND 2 MAX FROM ENDS. PUNCH AND DIMPE ON DRYWA RETURN SIDE 2 (49)

140 KNOCK DOWN (KD) CONNECTION HEAD 137 Drywall KD Sideight May, 2012 Z-NOTCH COMPRESSION ANCHORS MUION STIRRUP STOP NOTCH MUION BASE ANCHORS MUION DRYWA C PROFIE 16 GAUGE ONY 2 FACE STANDARD 1-1/2 AND 1-3/4 AVAIABE JAMB DEPTHS UNEQUA RABBET - 4-1/2 THROUGH 8-3/4 EQUA RABBET - 4-7/8 THROUGH 8-3/4 SI FACE 1-1/2 THROUGH 6 AVAIABE COMPRESSION ANCHORS BASE ANCHORS 2 FACE HAS STANDARD BASE ANCHOR (PUNCH FACE) 1-1/2 AND 1-3/4 FACE HAS OPTIONA BASE ANCHOR 4 0 X 8 0 MAXIMUM DOOR OPENING 8 0 X 8 0 MAXIMUM EEVATION OPENING SIZE AVAIABE IN SINGE AND DOUBE (SAME SIDE) SIDEIGHT REVERSE WEDED FOOTCIP SI NO HORIZONTA MUIONS AOWED SINGE DOOR OPENING ONY NON-RATED ONY ROUGH OPENING REQUIREMENTS: THE ROUGH OPENING HEIGHT EQUAS THE FINISHED OPENING HEIGHT +1. THE ROUGH OPENING WIDTH EQUAS THE FINISHED WIDTH +2.

141 138 Electroynx System X Options April, 2011 Hardwiring Made Easy The CURRIES X cable is equipped with the Electroynx System of plug-in connectors for fast, easy, connection to similarly equipped ASSA ABOY Hardware. The X cable has 15 conductors of 22 gauge wire in a PVC jacket, with Electroynx snap connectors on the hardware prep end only. Ship loose only. Power over Ethernet (PoE) cabels are also available. Check anchor interference with conduit, some loose anchor styles won t work. Some electric preps won t allow 1/2" drywall penetration for fire rated frames. Conduit is to be supplied and installed by others.