Storefront Installation Guide INSTALLATION INSTRUCTIONS

Size: px
Start display at page:

Download "Storefront Installation Guide INSTALLATION INSTRUCTIONS"

Transcription

1 STOREFRONT General Notes 1. Check contract documents and shop drawings, and understand and clarify any Field Verify Notes, approvals of drawings, and products required to be familiar with the project. Installation instructions are intended to be a reasonable guideline for installation of a product based on testing and common conditions. Conditions on a project may vary and deviations or special instructions should be defined in the shop drawings. Shop Drawings should take precedence and define project-specific products and installation. 2. All materials need to be inventoried to be certain everything required for installation is accounted for. 3. Materials need to be installed plumb, level, and true. 4. Work from project-defined benchmarks like center column lines, finished floors, or mullion spacing as defined by the Architectural drawings and the General Contractor. 5. All sealants need to be compatible with all materials. The Glazing Contractor and/or General Contractor are responsible for supplying sealants, and submitting any sealant compatibility and performance documentation. 6. Isolation of dissimilar materials, like aluminum and uncured concrete, should be prepared for. 7. Use a heavy bituminous paint, zinc chromate coating, or approved equal to isolate incompatible materials. 8. Protection and cleaning of materials are the responsibility of the Glazing and General Contractors. (Reference AAMA documentation, care, and maintenance.) 9. Diversity of Federal State and Local Building Codes are the responsibility of the Architect, Owner, and Customer to interpret compliance for the fenestration products used on the project. Boyd Aluminum is only a material supplier. 10. Boyd Aluminum is the material supplier of the fenestration product defined in the drawings and contract documents. Only fasteners and accessories within the system are supplied. Anchors, sealants, and fasteners to the surrounding conditions should be defined on the shop drawings and are normally the responsibility of the Glazing Contractor. 11. Due to changing fenestration parameters and evolving product lines, Boyd Aluminum reserves the right to change detailing and documentation commensurately without notification. Page Number 205

2 BOYD ENTRANCES 1. Boyd Entrance Systems are designed to offer a wide range of installation options. Review the frames with your project hardware requirements to ensure the options are compatible. 2. The use of a Loctite type product is recommended for hardware installation. Some items may already be prepared with Loctite. 3. Installation instructions are based on stocked hardware options. Special hardware may require further review. 4. Boyd offers door frames and door blanks for customers to fabricate their own hardware options. 5. Boyd can fabricate to customer-supplied hardware if frames and stiles are compatible. Boyd will only fabricate to hardware supplied. Boyd will not replace or be responsible for missing pieces or fabrication incompatible for those pieces. 6. Boyd fabrication from templates may be done, but absolutely no guarantee is given that the fabrication will be compatible without physical hardware. Page Number 206

3 STOREFRONT ENTRANCE FRAMES Frame #1: Butt Hinge and Continuous Hinge Frame. Figure A (Frame Layouts) The butt hinge and continuous hinge frames without a transom use an open frame header that has a screw boss that may interfere with pivot installation. Figure A Butt Hinge / Continuous Hinge Frame NOT USED WITH PIVOT FIGURE A BUTT HINGE / CONTINUOUS HINGE FRAME Page Number 207

4 Frame #2: Offset Pivot Frame. Figure B Offset pivot frame uses a header that omits the screw boss that interferes with the pivot installation. Figure B Offset Pivot Frame NOT USED WITH PIVOT FIGURE B OFFSET PIVOT FRAME Page Number 208

5 Frame #3: Transom Frame. Figure C Transom Glazing Deducts Figures D-1 and D-2 Transom frame is compatible with multiple hinge options. Transom frame options can include 1/4" or 1" glazing options. Figure C 1" GLZ Transom Frame FIGURE C 1" GLZ TRANSOM FRAME Page Number 209

6 Figure D-1 1 3/4" Standard Frames 1/4" Glazing Transom Frame Optional 1/4" Glz Transom Frame Figure D " Standard Frames 1/4" Glazing Transom Frame Optional 1/4" Glz Transom Frame Page Number 210

7 Frame #4: Transom Tube Frame. Figure E Transom Glazing Deducts Figures F-1 and F-2 The transom tube is designed to be compatible with concealed overhead closures. The transom tube is assembled using shear block assembly at the tube location. Transom frame is compatible with multiple hinge options. Transom tube frame options can include 1/4" or 1" glazing options. Figure E 1" GLZ Tube Transom Frame FIGURE E 1" GLZ TUBE TRANSOM FRAME Page Number 211

8 Figure F-1 1 3/4" Standard Frames 1/4" Glazing Tube Header Frame Figure F " Standard Frames 1" Glazing Tube Header Frame 1/4" Glazing Transom Frame Optional 1" GLZ Transom Frame Page Number 212

9 Frame #5: Center Set Frame. Figure G The center set frame is designed to be used with the double-acting door option. Figure G Center Set Frame FIGURE G CENTER SET FRAME Page Number 213

10 Frame #6: Center Set Transom Frame. Figure H Transom Glazing Deducts Refer to Figures F-1 and F-2 Transom frame options can include 1/4" or 1" glazing options. Figure H Center Set Transom Frame FIGURE H CENTER SET TRANSOM FRAME Page Number 214

11 BUTT HINGE FRAME UNIT ASSEMBLY (Exploded Butt Hinge Frame) Figure J 1. Verify opening size. 2. Assemble head and door jambs with #10 screws as shown; butter the frame header edges with sealant. 3. Door stops must be removed/not installed prior to assembly. 4. Threshold clip sill into frame as shown with Loctite. 5. Install hinges with Loctite. 6. Set frame into opening plumb and square. Block and anchor entrance frame to prevent movement on hardware mullions. 7. Fill frame jambs with sealant to channel water out of stops, as shown in Figure K. 8. Anchor thresholds with 1/4" FH fasteners through holes provided set in sealant. 9. Block and anchor frame through stop pocket at 4" 6" from corners and 16" O.C. or, as superseded by drawings and/or calculations. If using filler fasteners; may offset. Figures L-1 and L Show attention to anchoring hardware points plumb. 11. Snap in vertical door stops, then horizontal with sealant in reglet. Seal corners. 12. Clean the frame. Page Number 215

12 Figure J Butt Hinge Frame (2) # /4" (2) #10-12 X 1 1/4" PHL PH SMS PHL PH SMS (4) (4) #12-24 #12-24 PHL PHL FH MS FH MS UNDERCUT Undercut 4 41/2 1/2 BUTT Butt HINGE Hinge (4) #12-24 (4) #12-24 PHL FH PHL MS FH MS UNDERCUT Undercut (4) #12-24 (4) #12-24 PHL FH MS PHL FH MS UNDERCUT Undercut Butter w/ Sealant BUTTER W/ SEALANT Butter BUTTER w/ W/ Sealant SEALANT Snap-In SNAP-IN Door DOOR Stop STOP With WITH Weatherstrip WEATHERSTRIP (Not (NOT Shown SHOWN At Hinge AT HINGE Jamb JAMB For FOR Clarity) CLARITY) (2) #10-12 X 1 1/4" PHL PH SMS 4 1/2 4 1/2 BUTT Butt HINGE Hinge (4) (4)#12-24 PHL FH MS UNDERCUT Undercut Figure K (4) #12-24 PHL FH MS (4) #12-24 PHL Undercut FH MS UNDERCUT Backer Plate For BACKER PLATE FOR 4 1/2 Butt Hinge 4-1/2 BUTT HINGE (4) (4)#12-24 PHL FH MS UNDERCUT Undercut 4 1/2 4 1/2 BUTT Butt HINGE Hinge THRESHOLD Threshold CLIP Clip (2) #10-24(2)#10-24 PHL FH MS PHL Undercut FH MS UNDERCUT (2) #10-24 (2)#10-24 PHL FH FH MS MS UNDERCUT Undercut 1/4" PHL FH Seal SEAL And AND Tool TOOL At AT Threshold THRESHOLD FIGURE K (2)#10-24 PHL FH (2) MS #10-24 UNDERCUT PHL FH MS Undercut FIGURE J BUTT HINGE FRAME Threshold THRESHOLD Clip CLIP w/ W/ (2) (2)#10-24 PHL FH MS FH UNDERCUT MS Undercut Page Number 216

13 Figure L-1 Anchor ANCHOR At AT Center CENTER Of Glass OF GLASS Pocket POCKET DOOR Anchor ANCHOR Threshold THRESHOLD At AT CENTER Center OF Of DOOR Door FIGURE L-1 Figure L-2 Offset Fasteners If Using Frame Filler Fasteners Will Offset IF USING FRAME FILLER FASTENERS WILL OFFSET DOOR Anchor ANCHOR Threshold THRESHOLD At AT Center CENTER Of OF DOOR Door FIGURE L-2 OFFSET FASTENERS Page Number 217

14 HANG DOOR Figure M 1. Check frame to be sure it is plumb and square. 2. Inspect door leaf for damages. 3. Glazing a door on a table is easier, but it can be done vertically as well. See Figures N and O for demonstration. 4. Attach the push bar so it is level and square. 5. Install the door snap in interior stop. Seal corners. See Figure P. 6. Ensure the jack screw is not screwed down too far. 7. Set glass. 8. Snap in exterior bead. Note that verticals run through, and may require a trim to miss welds, see Figure P. 9. Attach the handle. 10. Position the door and fasten the hinges using Loctite. 11. To adjust the jack screw, place a wedge under the door to relieve pressure. Snug the jack screw gently to avoid glass breakage. Snap on the jack screw hole plug. 12. Clean door and frame. Page Number 218

15 Figure M 1/4-20 PHL PH Jack Screw 1/4-20 PHL PH JACK SCREW 1/4-20 PHL FH 1/4-20 PHL FH DOUBLE Double Set Stud SET STUD Pull PULL Handle HANDLE 1/4-20 Allen Keyed 1/4-20 ALLEN Set Screw KEYED SET SCREW #12-24 PHL FH MS FH UNDERCUT MS Undercut 1/4-20 UNC Grip 1/4-20 Open UNC End GRIP Rivnut OPEN END RIVNUT 1/4-20 PHL FH MS 1/4-20 PHL FH MS PUSH Push Bar BAR #12-24 PHL FH #12-24 MS Undercut PHL FH MS UNDERCUT Snap SNAP In Interior IN INTERIOR Stop STOP TO ADJUST To Adjust JACK Jack SREW, Screw, Relieve Pressure By RELIEVE PRESSURE BY Using A Wedge USING A WEDGE #12-24 PHL #12-24 PHL FH MS FH MS Undercut UNDERCUT FIGURE M Page Number 219

16 Figure P Sealant SEALANT Figure N If Not Already Done, IF NOT ALREADY DONE, TRIM CORNER Trim Corner OFF TO Off To MISS Miss WELDS. Welds. FIGURE P Interior Glass INTERIOR Stops GLASS With Gaskets STOPS WITH GASKETS Setting Chairs SETTING CHAIRS 4" 4" FROM From STILE Stile Interior INTERIOR Glass GLASS STOPS Stops WITH With GASKETS Gaskets Jack JACK Screw SCREW 3/4" HOLE Hole PLUG Plug FIGURE N Page Number 220

17 Figure O 3/4" Hole Plug 3/4" HOLE PLUG Jack Screw JACK SCREW Interior Glass INTERIOR GLASS Stops With Gaskets STOPS WITH GASKETS Setting Chairs SETTING CHAIRS 4" From Stile 4" FROM STILE FIGURE O Interior Glass INTERIOR GLASS Stops With Gaskets STOPS WITH GASKETS Page Number 221

18 PIVOT HINGE FRAME UNIT ASSEMBLY (Exploded Pivot Frame) Figure Q 1. Verify the opening size. 2. Assemble head and door jambs with #10 screws as shown; butter the frame header edges with sealant. 3. Door stops must be removed/not installed prior to assembly. 4. Threshold clip sill into frame as shown with Loctite. Half of the base pivot may be the threshold clip on a pivot hinged frame. 5. Install header pivot with Loctite. 6. Set frame into the opening, plumb and square. Block and anchor the entrance frame to prevent movement on hardware mullions. 7. Block and anchor pivot and set threshold in sealant with 1/4" FH fastener through fastener holes provided. See Figures Q and R. 8. Fill frame jambs with sealant to channel water out of stops as shown. See Figure S. 9. Block and anchor frame through stop pocket at 4" 6" from corners and 16" O.C. or, as superseded by drawings and/or calculations. If using filler, fasteners may offset. See Figures R-1 and R Be sure anchoring hardware points plumb. 11. Snap in vertical then horizontal door stops with sealant in reglet. Seal corners. 12. Clean frame. Page Number 222

19 Figure R-1 Anchor At Center Of Glass Pocket ANCHOR AT CENTER OF GLASS POCKET DOOR Anchor ANCHOR Threshold THRESHOLD At AT CENTER OF DOOR Center Of Door FIGURE R-1 Figure R-2 Offset Fasteners If Using Frame Filler, Fasteners Will Offset IF USING FRAME FILLER FASTENERS WILL OFFSET DOOR Anchor ANCHOR Threshold THRESHOLD At AT CENTER OF DOOR Center Of Door FIGURE R-2 OFFSET FASTENERS Page Number 223

20 Figure Q Offset Pivot Hinge Frame (3) (3) #10-12 #10-12 PHL PHL PH PH SMS Butter BUTTER w/ W/ Sealant SEALANT Top Pivot TOP Frame PIVOT Part FRAME PART 1/4-20 PHL 1/4-20 FH MS PHL Undercut FH MS UNDERCUT BUTTER Butter w/ W/ Sealant SEALANT (3) #10-12 PHL PH SMS Snap-In SNAP-IN Door DOOR Stop STOP With Weatherstrip WITH WEATHERSTRIP (Not Shown At (NOT Hinge SHOWN Jamb AT For HINGE Clarity) JAMB FOR CLARITY) INTERMEDIATE Intermediate PIVOT Pivot FRAME Frame PART Part 1/4-20 PHL 1/4-20 FH MS PHL Undercut FH MS UNDERCUT Figure S BOTTOM Bottom PIVOT Pivot FRAME Frame PART Part SHIM Shim PIVOT Pivot IF If REQUIRED Required #10-24 #10-24 PHL PHL FH FH MS MS FUNDERCUT Fundercut Fasten Pivot To FASTEN PIVOT TO Finished Floor FINISHED FLOOR w/ (2) 1/4" PHL FH W/ (2) 1/4" PHL FH 1/4" PHL FH Seal SEAL And AND Tool TOOL At AT Threshold THRESHOLD FIGURE S FIGURE Q OFFSET PIVOT HINGE FRAME Threshold THRESHOLD Clip CLIP w/ W/ (2) (2)#10-24 PHL FH MS FH UNDERCUT MS Undercut Page Number 224

21 HANG DOOR Figure T 1. Check frame to be sure it is plumb and square. 2. Inspect door leaf for damages. 3. Glazing a door on a table is easier, but it can be done vertically as well. See Figures N and O. 4. Attach the push bar level and square. 5. Install the door snap-in interior stop. Seal corners. See Figure P. 6. Ensure the jack screw is not screwed down too far. 7. Set glass. 8. Snap in exterior bead. Note that verticals run through, and may require a trim to miss welds. See Figure P. 9. Attach the handle. 10. Install pivots using Loctite. 11. Depress head pin in upper pivot. See Figure U. 12. If the intermediate pivot is installed, you will need to remove the cover and retract it. See Figure V. 13. Position the door and adjust the lower pivot stud, then tighten the set screw. See Figure W. 14. Reposition the door and release the head pin on upper pivot. 15. If available, and an adjustment is needed, remove the cover on lower pivot for final adjustment. See Figure W. 16. Snug down the intermediate pivot and replace cover. 17. To adjust the jack screw, place a wedge under the door to relieve pressure. Snug the jack screw gently to avoid glass breakage. Snap on jack screw hole plug. 18. Clean door and frame. Page Number 225

22 Figure T 1/4-20 PHL PH Jack Screw 1/4-20 PHL PH JACK SCREW 1/4-20 PHL FH 1/4-20 Double Set PHL Stud FH DOUBLE SET STUD Pull Handle PULL HANDLE Top TOP Pivot PIVOT Door DOOR PartPART 1/4-20 Allen Keyed 1/4-20 Set ALLEN Screw KEYED SET SCREW 1/4-20 UNC Grip 1/4-20 Open UNC End GRIP Rivnut OPEN END RIVNUT 1/4-20 PHL FH MS PUSH Push BAR Bar Intermediate INTERMEDIATE PIVOT Pivot DOOR Door PART Part #12-24 #12-24 PHL PHL FH FH MS MS UNDERCUT Undercut Snap In Interior SNAP IN Stop INTERIOR STOP To Adjust Jack Screw, TO ADJUST Relieve JACK Pressure SCREW, By RELIEVE PRESSURE Using A Wedge BY USING A WEDGE To TO Adjust ADJUST Pivot PIVOT Relieve Pressure RELIEVE By Using PRESSURE A Wedge BY USING A WEDGE. PIVOT Pivot MAY May NEED Need TO To BE Be SHIMMED Shimmed & SHOULD & Should BE INSTALLED Be Installed PLUMB Plumb Bottom Pivot BOTTOM PIVOT Door Part DOOR PART FIGURE T Page Number 226

23 Depress Head Pin Before DEPRESS HEAD PIN BEFORE Positioning Door, Then Release POSITIONING After Door DOOR, Is Positioned THEN RELEASE AFTER DOOR IS POSITIONED Figure U Top Pivot Figure V Intermediate Pivot FIGURE U TOP PIVOT Remove Cover To Retract Pin REMOVE COVER TO RETRACT PIN FIGURE V INTERMEDIATE PIVOT Figure W Bottom Pivot If Available, Remove Cover For Adjustment IF AVAILABLE, REMOVE COVER FOR ADJUSTMENT SET SCREW Set Screw FIGURE W BOTTOM PIVOT Page Number 227

24 TRANSOM FRAME UNIT ASSEMBLY (Exploded Transom Frame) Figure X 1. Verify opening size. 2. Assemble head, horizontal, and door jambs with #10 screws as shown; butter the frame header edges with sealant. 3. Door stops must be removed/not installed prior to assembly. 4. Threshold clip sill into frame, as shown, with Loctite. Half of the base pivot may be the threshold clip on a pivot hinged frame. See Figure Y. 5. Install pivots or hinges with Loctite. 6. Set frame into opening plumb and square. Block and anchor entrance frame to prevent movement on hardware mullions. 7. Block and anchor pivot and set threshold in sealant with 1/4" FH fasteners through fastener holes provided. See Figure Z-1 and Z Fill frame jambs with sealant to channel water out of stops as shown. See Figure Y. 9. Block and anchor frame through stop pocket at 4" 6" from corners and 16" O.C. or as superseded by drawings and/or calculations. If using filler fasteners, may offset. See Figure Z-1 and Z Show attention to anchoring hardware points plumb. 11. Snap in vertical, then horizontal door stops with sealant in reglet. Seal the corners. 12. Install interior transom sash in thin sealant. 13. Seal corners and place transom setting blocks at 1/8" 1/4" point locations. See Figure AA. 14. Set glass in transom. Install glazing wedge. 15. Clean frame. 16. Install door. See Figure BB for installation, and Figures N and O for glazing. 17. Clean door and frame. Page Number 228

25 Figure X Transom Pivot Frame (2) #10-12 PHL PH SMS Butter w/ Sealant BUTTER W/ SEALANT Glazing GLAZING Wedge WEDGE Butter BUTTER w/ Sealant W/ SEALANT (2) #10-12 PHL PH SMS (2) #10-12 PHL PH SMS (3) #10-12 PHL PH SMS BUTTER Butter W/ w/ SEALANT Sealant Top Pivot TOP Frame PIVOT Part FRAME PART 1/4-20 PHL FH MS TRANSOM Transom SASH Sash Snap-In Door Stop w/ SNAP-IN Weatherstrip DOOR (Not STOP Shown W/ WEATHERSTRIP At Hinge Jamb For (NOT Clarity) SHOWN AT HINGE JAMB FOR CLARITY) Butter BUTTER w/ W/ Sealant SEALANT Intermediate Pivot Frame INTERMEDIATE PIVOT Part FRAME PART 1/4-20 PHL PHL FH FH MS MS Bottom BOTTOM Pivot Frame PIVOT Part FRAME PART SHIM PIVOT Shim Pivot IF REQUIRED If Required #10-24 PHL FH MS #10-24 PHL FH MS UNDERCUT Undercut Fasten Pivot To Finished Floor w/ (2) 1/4" PHL FASTEN FH PIVOT TO FINISHED FLOOR W/ (2) 1/4" PHL FH 1/4" PHL FH (3) #10-12 PHL PH SMS (3) #10-12 PHL PH SMS Figure Y FIGURE Y Seal And Tool SEAL AND TOOL At Threshold AT THRESHOLD FIGURE X TRANSOM PIVOT FRAME Threshold THRESHOLD Clip CLIP w/ W/ (2) (2) #10-24 PHL PHL FH FH MsMS Page Number 229

26 Figure Z-1 Anchor At Center Of Glass Pocket ANCHOR AT CENTER OF GLASS POCKET Anchor At Center ANCHOR AT CENTER Of Glass OF GLASS Pocket POCKET DOOR Anchor ANCHOR Threshold THRESHOLD At Center AT CENTER Of OF Door DOOR FIGURE Z-1 Figure Z-2 Offset Fasteners If Using Frame Filler, Fasteners Will Offset IF USING FRAME FILLER FASTENERS WILL OFFSET If IF Using USING FRAME Frame FILLER Filler, Fasteners FASTENERS WILL Will OFFSET Offset DOOR Anchor Threshold At Center Of Door ANCHOR THRESHOLD AT CENTER OF DOOR FIGURE Z-2 OFFSET FASTENERS Page Number 230

27 Figure AA Install INSTALL Interior INTERIOR Transom Sash In Thin Sealant TRANSOM SASH IN THIN SEALANT Seal SEAL Corners CORNERS Place 2 Setting PLACE 2 Blocks SETTING at 1/8" BLOCKS Or 1/8 OR Point 1/4 Locations POINT LOCATIONS FIGURE AA Page Number 231

28 Figure BB 1/4-20 1/4-20 PHL PHL PH JACK Jack SCREW Screw Top TOP Pivot PIVOT Door DOOR Part PART 1/4-20 Allen 1/4-20 Keyed ALLEN Set KEYED SET SCREW Screw 1/4-20 PHL FH 1/4-20 Double PHL Set Stud FH DOUBLE SET STUD Pull PULL Handle HANDLE #12-24 PHL FH MS Undercut UNDERCUT 1/4-20 1/4-20 UNC UNC GRIP Grip OPEN Open END End RIVNUT Rivnut 1/4-20 PHL FH MS PUSH Push BAR Bar Intermediate INTERMEDIATE Pivot PIVOT Door DOOR Part PART #12-24 #12-24 PHL PHL FH FH MS MS UNDERCUT Undercut SNAP Snap IN In INTERIOR Interior Stop STOP TO ADJUST To Adjust JACK Jack SCREW, Screw, Relieve RELIEVE Pressure PRESSURE By Using BY A USING A WEDGE. Wedge BOTTOM Bottom Pivot PIVOT DOOR Door Part PART To TO Adjust ADJUST Pivot, PIVOT Relieve RELIEVE Pressure PRESSURE BY USING By Using A WEDGE A Wedge PIVOT Pivot May MAY Need NEED To TO Be BE Shimmed SHIMMED And AND SHOULD Should BE INSTALLED Be Installed PLUMB Plumb FIGURE BB Page Number 232

29 TRANSOM TUBE FRAME UNIT ASSEMBLY (Exploded Transom Tube Frame) Figure CC 1. Verify opening size. 2. Assemble head, horizontal with Shear Blocks, and door jambs with #10 screws, as shown. Butter the frame header edges with sealant. If using offset pivot, shear block will need to be field modified. See Figure DD. 3. Door stops must be removed/not installed prior to assembly. 4. Threshold clip sill into frame as shown with Loctite. Half of the base pivot may be the threshold clip on a pivot hinged frame. 5. Install pivots or hinges with Loctite. 6. Set frame into the opening plumb and square. Block and anchor entrance frame to prevent movement on hardware mullions. 7. Block and anchor pivot and set threshold in sealant anchor with 1/4" FH fasteners through fastener holes provided. See Figures EE-1 and EE Fill frame jambs with sealant to channel water out stops as shown. See Figure FF. 9. Block and anchor frame through stop pocket at 4" 6" from corners and 16" O.C. or as superseded by drawings and/or calculations. If using filler fasteners, may offset. See Figures EE-1 and EE Show attention to anchoring hardware points plumb. 11. Do not install door stops at this point. 12. Install interior transom sash in thin sealant. See Figure EE Seal corners and place transom setting blocks at 1/8" 1/4" point locations. See Figure AA. 14. Set glass in transom. Install glazing wedge. 15. Clean frame. 16. Install concealed overhead closure. Refer to manufacturer s hardware instructions degree pivot. See Figure GG degree butt hinge. See Butt Hinge Frame, Figure J. 19. Install arm cover. See Figure GG. 20. Trim and install vertical door stops. 21. Install door. See Figure GG for installation, and Figures N and O for glazing. 22. Attach arm and adjust, per hardware instructions. See Figure GG. 23. Clean door and frame. WHEN When USING Using OFFSET Offset PIVOT Pivot Front FRONT Leg LEG Of Shear OF SHEAR Block BLOCK Will WILL Need NEED To TO Be BE Removed REMOVED Figure DD FIGURE DD Page Number 233

30 (2) #10-12 PHL PH SMS (2) #10-12 PHL PH SMS Figure CC Transom Tube Frame Butter w/ Sealant BUTTER W/ SEALANT ANCHOR Anchor CLIP Clip W/ w/ (3) #10 PHL FH SMS (3) #10 PHL FH SMS (Requires Field ( REQUIRES FIELD Modification To Allow For MODIFICATION TO Top Pivot Frame Part) ALLOW FOR TOP PIVOT FRAME PART) #10 PHL FH SMS Undercut UNDERCUT TRANSOM Transom SASH Sash Butter BUTTER w/ Sealant W/ SEALANT (2) #10-12 PHL PHL PH PH SMS SMS Coc Anchor Bracket w/ #10-32 COC ANCHOR PHL BRACKET FH MS UC W/ #10-32 PHL FH MS UC TOP PIVOT Top Pivot FRAME Frame PART Part 1/4-20 1/4-20 PHL PHL FH FH MS MS Coc Angle COC Bracket ANGLE w/ BRACKET (2) 1/4-20 W/ Hex (2) Head 1/4-20 & (2) HEX Lock HEAD Washers & (2) LOCK WASHERS 1/4-20 1/4-20 PHL PHL FH FH MS MS Intermediate Pivot INTERMEDIATE PIVOT Frame Part FRAME PART 1/4-20 PHL FH MS Bottom Pivot BOTTOM PIVOT FRAME Frame PARTPart SHIM PIVOT Shim Pivot IF REQUIRED If Required #10-24 #10-24 PHL PHL FH FH MS MS UNDERCUT Undercut #10 PHL #10 FH PHL SMS FH SMS UNDERCUT Undercut #10 PHL FH SMS Fasten Pivot To Finished Floor FASTEN w/ (2) PIVOT 1/4" PHL TO FH FINISHED FLOOR W/ (2) 1/4" PHL FH 1/4" PHL FH Set SET In IN Sealant SEALANT Anchor ANCHOR Clip CLIP w/ (4) W/ #10 (4) PHL FH SMS #10 PHL FH SMS Snap-In SNAP-IN Door DOOR Stop STOP w/ Weatherstrip W/ WEATHERSTRIP (Not Shown At Hinge (NOT Jamb SHOWN For Clarity) AT HINGE JAMB FOR CLARITY) Figure FF Seal And Tool SEAL AND TOOL At Threshold AT THRESHOLD FIGURE CC TRANSOM TUBE FRAME FIGURE FF Threshold THRESHOLD Clip CLIP w/ W/ (2) (2) #10-24 #10-24 PHL PHL FH FH MS MS Page Number 234

31 Use FH Fasteners To Avoid Interference w/ Concealed USE FH FASTENERS TO AVOID INTERFERENCE W/ CONCEALED Overhead OVERHEAD Closer CLOSER Figure EE-1 Anchor At Center Of Glass Pocket ANCHOR AT CENTER OF GLASS POCKET Set In Sealant SET IN SEALANT Field Trim This Leg Off When Using Offset Pivot FIELD TRIM THIS LEG OFF WHEN USING OFFSET PIVOT Anchor At Center Of Glass Pocket ANCHOR AT CENTER OF GLASS POCKET DOOR Anchor Threshold At Center Of Door ANCHOR THRESHOLD AT CENTER OF DOOR FIGURE EE-1 Page Number 235

32 Use FH Fasteners To Avoid Interference w/ Concealed USE FH FASTENERS TO AVOID INTERFERENCE W/ Overhead CONCEALED OVERHEAD Closer CLOSER Figure EE-2 Offset Fasteners If Using Frame Filler, Fasteners Will Offset IF USING FRAME FILLER FASTENERS WILL OFFSET SET IN SEALANT Set In Sealant Field Trim This Leg Off When FIELD TRIM THIS LEG OFF WHEN Using USING Offset OFFSET PIVOT Pivot If Using Frame Filler, Fasteners Will Offset IF USING FRAME FILLER FASTENERS WILL OFFSET DOOR Anchor Threshold At ANCHOR THRESHOLD Center AT CENTER Of OF Door DOOR FIGURE EE-2 OFFSET FASTENERS Page Number 236

33 Figure GG #12-24 PHL FH #12-24 PHL FH MS MS Undercut UNDERCUT 1/4-20 1/4-20 PHL PHL PH JACK PH Jack SCREW Screw 1/4-20 Allen Keyed Set Screw 1/4-20 ALLEN KEYED SET SCREW 1/4-20 PHL 1/4-20 FH Double PHL FH Set DOUBLE SET STUD Stud 1/4-20 1/4-20 UNC Grip UNC Open GRIP End OPEN END RIVNUT Rivnut Pull PULL Handle HANDLE Top TOP Pivot PIVOT Door DOOR Part PART Attach ATTACH To TO PIN Pin ON On SLIDE Slide Arm Cover ARM COVER #10 #10 PHL FH FH SMS 1/4-20 PHL FH MS PUSH Push BAR Bar Intermediate INTERMEDIATE Pivot PIVOT Door DOOR Part PART #12-24 Phl PHL Fh FH MS Ms UNDERCUT Undercut SNAP Snap IN In INTERIOR Interior Stop STOP To Adjust Jack Screw, TO ADJUST Relieve JACK Pressure SCREW, By RELIEVE PRESSURE Using A Wedge BY USING A WEDGE To Adjust Pivot, Relieve TO ADJUST Pressure PIVOT By Using RELIEVE A Wedge PRESSURE BY USING A WEDGE PIVOT MAY Pivot NEED May Need TO BE To SHIMMED Be Shimmed & Should Be Installed Plumb & SHOULD BE INSTALLED PLUMB Bottom BOTTOM Pivot PIVOT Door DOOR PartPART FIGURE GG Page Number 237

34 CENTER SET AND CENTER SET TRANSOM FRAME UNIT ASSEMBLY (Exploded Center-Set Frame) Figure HH 1. Verify opening size. 2. Assemble head, horizontal with Shear Blocks, and door jambs with #10 screws, as shown. Butter the frame header edges with sealant. 3. Threshold clip sill into frame as shown with Loctite. 4. Install threshold or floor pivot with Loctite. 5. Set frame into opening plumb and square. Block and anchor entrance frame to prevent movement on hardware mullions. 6. Block and anchor pivot and set threshold in sealant anchor with 1/4" FH fasteners through fastener holes provided. See Figure JJ-1 and JJ Block and anchor frame through center at 4" 6" from corners and 16" O.C. or as superseded by drawings and/or calculations. If using filler fasteners, may offset. See Figures JJ-1 and JJ Show attention to anchoring hardware jambs and points plumb. 9. Install interior transom sash in thin sealant. 10. Seal corners and place transom setting blocks at 1/8" 1/4" point locations. See Figure AA. 11. Set glass in transom. Install glazing wedge. 12. Clean frame. 13. Install concealed overhead closure. Refer to manufacturer s hardware instructions. 14. Install door. See Figure KK. 15. Attach arm and adjust, per hardware instructions. 16. Clean door and frame. Page Number 238

35 Figure HH Center Set Frame 1/4" 1/4" Shim SHIM (For ( Use FOR w/ USE 2" WITH 2" HEADER) Header) COC COC JAMB Jamb BRACKET Bracket #10 #10 PH PH SELF-THREADING Self-Threading BUTTER Butter W/ w/ SEALANT Sealant Concealed Overhead Closer CONCEALED OVERHEAD CLOSER COC Angle Bracket COC ANGLE BRACKET 1/4-20 1/4-20 HEX Hex HEAD Head MS MS w/ Washer W/ WASHER COC Cover Plate COC COVER PLATE #10-24 FH MS #10-24 FH MS Butter w/ Sealant BUTTER W/ SEALANT Threshold Clip THRESHOLD CLIP (2) #10-24 PHL FH MS (2) #10-24 Undercut PHL FH MS UNDERCUT Pivot PIVOT Stud STUD & & Bearing BEARING Hex HEX Lock LOCK Nut NUT Threshold THRESHOLD Adapter ADAPTER Nut NUT Hex Jamb Nut HEX JAM NUT 1/4" PHL FH PIVOT Pivot STUD Stud & & BEARING Bearing HEX Hex LOCK Lock NUT Nut FLOOR Floor MOUNTED Mounted PIVOT Pivot BASE Base (2)#10-24 PHL FH FH MS MS UNDERCUT Undercut Threshold THRESHOLD Clip CLIP w/ (2) #10-24 PHL W/ (2) FH #10-24 MS Undercut PHL FH MS FIGURE HH UNDERCUT CENTER SET FRAME Page Number 239

36 Figure JJ-1 Anchor Through Center ANCHOR THROUGH CENTER DOOR Anchor Threshold At ANCHOR THRESHOLD AT Center CENTER Of OF DOOR Door FIGURE JJ-1 Figure JJ-2 Offset Fasteners If Using Frame Filler, Fasteners Will Be Offset IF USING FRAME FILLER FASTENERS WILL BE OFFSET DOOR Anchor Threshold At Center Of Door ANCHOR THRESHOLD AT CENTER OF DOOR FIGURE JJ-2 OFFSET FASTENERS Page Number 240

37 Figure KK 1/4-20 PHL 1/4-20 PH Jack PHL Screw PH JACK SCREW 1/4-20 PHL FH MS 1/4-20 PHL FH MS 1/4-20 Allen Keyed 1/4-20 Set ALLEN Screw KEYED SET SCREW 1/4-20 UNC Grip Open End Rivet 1/4-20 UNC GRIP OPEN END RIVET 1/4-20 PHL FH 1/4-20 Double PHL Set Stud FH DOUBLE SET STUD Push PUSH Bar BAR FIGURE KK Page Number 241

38 BAM Storefront SUBSILL SIDELITE TO DOOR FRAME Figure LL 1. Set subsill in sealant adjacent jamb. 2. Back seal subsill and filler up approximately 6". 3. Fill glazing cavity with sealant above subsill and tool to shed water into subsill. 4. See Storefront to complete. Set Subsill And Seal To Mull Fill Cavity SET SUBSILL AND SEAL TO MUL FILL CAVITY TO To SUBSILL Subsill HEIGHT Height SO So WATER Water IS Is FORCED Forced TO To EVACUATE Evacuate THROUGH Through SUBSILL Subsill Figure LL Seal SEAL Up UP FILLER Filler Full FULL Length LENGTH Both BOTH Sides SIDES Set SET Frame FRAME In IN Sealant SEALANT Fill FILL Pocket POCKET Here HERE To TO Threshold THRESHOLD Height HEIGHT 1221 BAM BAM FIGURE LL Page Number 242

Storefront Installation Guide

Storefront Installation Guide Storefront General Notes: 1. Check Contract Documents and Shop Drawings. Understand and clarify any Field Verify Notes and approvals of drawings and products to be familiar with the project. Installation

More information

SERIES 5001 SLIDING GLASS DOOR PATIO DOORS INSTALLATION GUIDE

SERIES 5001 SLIDING GLASS DOOR PATIO DOORS INSTALLATION GUIDE PATIO DOORS INSTALLATION GUIDE These instructions cover general installation conditions. Improper installation could affect your doors operation and warranty. Deviations from these instructions should

More information

NARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE. Installation Instructions

NARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE. Installation Instructions NARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE Installation Instructions PART Y015 JUNE 2016 Table of Contents Section 1. GENERAL NOTES AND GUIDELINES... 2. DOOR HARDWARE A. Locks B. Push/Pulls

More information

SERIES 300 SINGLE HUNG WITH FIN WINDOW INSTALLATION

SERIES 300 SINGLE HUNG WITH FIN WINDOW INSTALLATION IMPORTANT INFORMATION: WHETHER IT BE LOCATION OR INSTALLATION TYPE, NOT ALL WINDOW TYPES CAN BE INSTALLED IN ALL AREAS OR WALL CONDITIONS. CONSULT YOUR LOCAL BUILDING CODE DEPARTMENT FOR ANY REGULATIONS

More information

SERIES 300 SINGLE HUNG WINDOW INSTALLATION

SERIES 300 SINGLE HUNG WINDOW INSTALLATION IMPORTANT INFORMATION: WHETHER IT BE LOCATION OR INSTALLATION TYPE, NOT ALL WINDOW TYPES CAN BE INSTALLED IN ALL AREAS OR WALL CONDITIONS. CONSULT YOUR LOCAL BUILDING CODE DEPARTMENT FOR ANY REGULATIONS

More information

INSTALLATION INSTRUCTIONS. Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING

INSTALLATION INSTRUCTIONS. Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING JANUARY, 2014 1 INSTALLATION Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING INSTRUCTIONS 2 FRAME ASSEMBLY JANUARY, 2014 601442 SHEAR BLOCK BALL BEARING NRP BUTT (FACTORY APPLIED

More information

INSTALLATION INSTRUCTIONS Frames and Entrance Doors

INSTALLATION INSTRUCTIONS Frames and Entrance Doors INSTALLATION INSTRUCTIONS Frames and Entrance Doors J 3010 Rice Mine Road, Tuscaloosa, Alabama 35406 1-800-772-7737 Fax 1-800-443-6261 www.coralind.com A Division of Coral Industries, Inc. FRAMES and ENTRANCES

More information

ELEPHANT DOOR SYSTEMS SERIES E1200

ELEPHANT DOOR SYSTEMS SERIES E1200 INSTALLATION INSTRUCTIONS ELEPHANT DOOR SYSTEMS SERIES E1200 Phone: (800) 262-5151 Fax: (866) 262-3299 crlaurence.com usalum.com crl-arch.com AVDB3096 03.13 TABLE OF CONTENTS SUBJECT PAGE GENERAL INSTALLATION

More information

14000 Series. Fabrication and Installation Instructions

14000 Series. Fabrication and Installation Instructions 14000 Series Fabrication and Installation Instructions Revision May 2013 Table of Contents GENERAL CONSTRUCTION NOTES...3 EXTRUDED ALUMINUM PARTS...5 ACCESSORIES...8 OVERVIEW...10 FRAME FABRICATION...15

More information

14000 I/O Series Flush Glaze. Fabrication and Installation Instructions

14000 I/O Series Flush Glaze. Fabrication and Installation Instructions 14000 I/O Series Flush Glaze Fabrication and Installation Instructions Last saved on 12/18/2009 Table of Contents GENERAL CONSTRUCTION NOTES...3 EXTRUDED ALUMINUM PARTS...4 ACCESSORIES...5 OVERVIEW...6

More information

INSTALLATION INSTRUCTIONS SIDELITE ASSEMBLY SERIES 900 TERRACE DOOR AND SERIES 925 PATIO DOOR

INSTALLATION INSTRUCTIONS SIDELITE ASSEMBLY SERIES 900 TERRACE DOOR AND SERIES 925 PATIO DOOR INSTALLATION INSTRUCTIONS SIDELITE ASSEMBLY SERIES 900 TERRACE DOOR AND SERIES 925 PATIO DOOR Phone: (800) 262-5151 Fax: (866) 262-3299 crlaurence.com usalum.com crl-arch.com 11M0292 HANDLING, STORAGE,

More information

4500 Series. Fabrication and Installation Instructions

4500 Series. Fabrication and Installation Instructions 4500 Series Fabrication and Installation Instructions E4500 Series July, 2017 Table of Contents GENERAL CONSTRUCTION NOTES... 3 EXTRUDED ALUMINUM PARTS... 5 ACCESSORIES... 7 OVERVIEW... 8 FRAME FABRICATION...

More information

14000 Series. Fabrication and Installation Instructions

14000 Series. Fabrication and Installation Instructions 14000 Series Fabrication and Installation Instructions 14000 Series Revision December 01, 2009 Table of Contents GENERAL CONSTRUCTION NOTES... 3 EXTRUDED ALUMINUM PARTS... 4 ACCESSORIES... 7 OVERVIEW...

More information

GENERAL INSTALLATION GUIDELINES

GENERAL INSTALLATION GUIDELINES 1551 MT. ROSE AVENUE YORK PA 17403-2909 (717) 849-8100 GENERAL INSTALLATION GUIDELINES For Receptor Systems Approved 08/31/2018 Installation Guideline Disclaimer This document contains general installation

More information

SERIES BW3250 BLAST WALL TABLE OF CONTENTS INSTALLATION INSTRUCTIONS GENERAL NOTES

SERIES BW3250 BLAST WALL TABLE OF CONTENTS INSTALLATION INSTRUCTIONS GENERAL NOTES I N S TA L L AT I O N I N S T R U C T I O N S BW3250 BLAST RESISTANT CURTAIN WALL Page 2 SERIES BW3250 BLAST WALL TABLE OF CONTENTS United States Aluminum PAGE GENERAL NOTES...2 and 3 FABRICATION...4 through

More information

GENERAL INSTALLATION GUIDELINES

GENERAL INSTALLATION GUIDELINES 1551 MT. ROSE AVENUE YORK PA 17403-2909 (717) 849-8100 GENERAL INSTALLATION GUIDELINES For Receptor Systems Approved 9/29/2017 Installation Guideline Disclaimer This document contains general installation

More information

Installation Instructions

Installation Instructions Installation Instructions 200 Series Curtainwall 3056 WALKER RIDGE DR. NW, SUITE G WALKER, MI 49544 800-866-2227 dependable@tubeliteinc.com Revised April 2014 dependable@tubeliteinc.com Page 1 TABLE OF

More information

INSTALLATION INSTRUCTIONS 2 x 4 1/2 for 1 Glass

INSTALLATION INSTRUCTIONS 2 x 4 1/2 for 1 Glass INSTALLATION INSTRUCTIONS 2 x 4 1/2 for 1 Glass Deep pocket allows for direct anchor attachment to substrate without flat filler plate. 1/4 Ø perimeter anchor holes allows for direct anchor attachment

More information

DHS-500 IMPACT SYSTEM INSTALLATION MANUAL

DHS-500 IMPACT SYSTEM INSTALLATION MANUAL DHS-500 IMPACT SYSTEM INSTALLATION MANUAL TABLE OF CONTENTS SECTION PAGE GENERAL NOTES 3 EXTRUSION & PARTS IDENTIFICATION 4-5 DETERMINE FRAME SIZE 6 FABRICATE VERTICAL MULLIONS & FILLERS 7-8 FABRICATE

More information

INSTALLATION INSTRUCTIONS SERIES 487 CENTER GLAZED WITH 1-1/2" TRIM OFFICE PARTITIONS

INSTALLATION INSTRUCTIONS SERIES 487 CENTER GLAZED WITH 1-1/2 TRIM OFFICE PARTITIONS INSTALLATION INSTRUCTIONS SERIES 87 CENTER GLAZED WITH -/" TRIM OFFICE PARTITIONS Phone: (800) -6 Fax: (800) 58-7 crlaurence.com usalum.com crl-arch.com M056_Rev_D SERIES 87 OFFICE PARTITIONS CENTER GLAZED

More information

Swing Door Installation Manual

Swing Door Installation Manual Manual 20D/35D/50D 20DH/35DH 40M/50M 25FD 35XT 50XT 01-4000-03 2010 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes.......................................

More information

YSD 400 Sliding Door System Installation Manual

YSD 400 Sliding Door System Installation Manual System Installation Manual 2006 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii PARTS DESCRIPTION

More information

FG-5100T STORMMAX INSTALLATION AND GLAZING MANUAL NOTE:

FG-5100T STORMMAX INSTALLATION AND GLAZING MANUAL NOTE: BuildingEnvelope R FG-5100T STORMMAX INSTALLATION AND GLAZING MANUAL NOTE: THE INSTALLATION DETAILS FOUND IN THIS PACKAGE ARE GENERIC AND ARE FOR REPRESENTATION ONLY WITH THE INTENT OF GIVING THE INSTALLATION

More information

Heavy Wall Applied Stop Tube Frame and Door Installation

Heavy Wall Applied Stop Tube Frame and Door Installation INSTALLATION INSTRUCTIONS Heavy Wall Applied Stop Tube Frame and Door Installation Read all instructions before beginning installation. These instructions are provided to help prevent installation problems

More information

PIVOT DOOR 3400P INSTALLATION INSTRUCTIONS

PIVOT DOOR 3400P INSTALLATION INSTRUCTIONS Table of Contents I. Tools, Sealant Requirements, Anchor Recommended Table...1 II. Opening, Frame & Panel Verification...2-3 III. Frame Assembly...4 IV. Frame Installation...5-7 V. Glazing Instructions...8

More information

Definitions and Design Considerations... W-CR-2

Definitions and Design Considerations... W-CR-2 General Information SECTION DIRECTORY Definitions and Design Considerations... W-CR-2 Combination Assembly Recommendations and Limitations Typical Sealant... W-CR-4 Single-Unit Opening... W-CR-4 Two-Way

More information

YCW 752 Outside Glazed Curtain Wall System Installation Manual

YCW 752 Outside Glazed Curtain Wall System Installation Manual YCW 752 Outside Glazed Curtain Wall System Installation Manual 2007 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................

More information

Senior Swing. Caution

Senior Swing. Caution *740132* 740132 2800 Overhead Concealed Series 9500 Surface Applied Series Senior Swing Installation Instructions Caution LCN Senior Swing The Senior Swing Power Operator System is a low energy product

More information

SERIES 900 TERRACE DOOR WITH TRANSOM AND SIDELITES

SERIES 900 TERRACE DOOR WITH TRANSOM AND SIDELITES INSTALLATION INSTRUCTIONS SERIES 900 TERRACE DOOR WITH TRANSOM AND SIDELITES Phone: (800) 262-5151 Fax: (866) 262-3299 crlaurence.com usalum.com crl-arch.com 11M0172_REV_A HANDLING, STORAGE, AND PROTECTION

More information

YES 45 TU Thermal Storefront System Installation Manual

YES 45 TU Thermal Storefront System Installation Manual Installation Manual 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii PARTS DESCRIPTION Framing

More information

INSTALLATION INSTRUCTIONS ENTICE SERIES PREMIUM ENTRANCE SYSTEM EXTERIOR GLAZE

INSTALLATION INSTRUCTIONS ENTICE SERIES PREMIUM ENTRANCE SYSTEM EXTERIOR GLAZE INSTALLATION INSTRUCTIONS ENTICE SERIES PREMIUM ENTRANCE SYSTEM EXTERIOR GLAZE Phone: (800) 421-6144 Fax: (800) 582-7501 crlaurence.com usalum.com crl-arch.com 11M0230 HANDLING, STORAGE, AND PROTECTION

More information

Thermally Broken Framing and Door Installation

Thermally Broken Framing and Door Installation INSTALLATION INSTRUCTIONS Thermally Broken Framing and Door Installation IMPORTANT: Read all instructions before beginning installation. These instructions are provided to help prevent installation problems

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Thermally Broken Framing and Door Installation SL-450TB (2" x 4-1/2" with 1" Glazing) & SL-600TB (2" x 6" with 1" Glazing) IMPORTANT: Read all instructions before beginning installation.

More information

Series Exterior glazed curtain wall. Installation Instructions

Series Exterior glazed curtain wall. Installation Instructions Series 5500 Exterior glazed curtain wall Installation Instructions Part NO. Y550 November 2016 TABLE OF CONTENTS SECTION S-5500 SCREW SPLINE CURTAIN WALL PAGE I. General Notes and Guidelines.. 3-4 II.

More information

Illustration Part Description Base List Weight/ Ft./ Box Number Price/S.L. S.L. S.L. Qty.

Illustration Part Description Base List Weight/ Ft./ Box Number Price/S.L. S.L. S.L. Qty. Prices DO NOT include glazing gaskets or weathering. See Accessories sheet. Exterior Glazed Back Members for 1" Glass Illustration Part Description Base List Weight/ Ft./ Box Price/S.L. S.L. S.L. Qty.

More information

MODEL: STORMMAX-MSD-FG-5000-DRY

MODEL: STORMMAX-MSD-FG-5000-DRY MODEL: STORMMAX-MSD-FG-5000-DRY MEDIUM STILE HURRICANE RESISTANT DOORS WITH FG-5000 FRAMES MONOLITHIC LAMINATED GLASS - DRY GLAZED OHSC H6331 O.H.C.C H6333 MID-PANEL MEETING STILES HD6184 HD6186 VD6145

More information

350/500 HEAVY WALL TM IR ENTRANCES 1

350/500 HEAVY WALL TM IR ENTRANCES 1 JUNE, 202 30/00 HEAVY WALL TM IR ENTRANCES FEATURES Blast Mitigation Product Features 30 medium stile has 3-/2" vertical stile, 3-/2" top and 6-/2" bottom rail 00 wide stile has " vertical stile, " top

More information

YCW 750 OG Outside Glazed Curtain Wall System Installation Manual

YCW 750 OG Outside Glazed Curtain Wall System Installation Manual YCW 750 OG Outside Glazed Curtain Wall System Installation Manual 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................

More information

YCW 750 IG Inside Glazed Curtain Wall System Installation Manual

YCW 750 IG Inside Glazed Curtain Wall System Installation Manual Installation Manual 2014 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION YCW 750 IG Framing Members... Page 1 to 3

More information

Installation Instructions for Vista Air Vertically Folding Walls

Installation Instructions for Vista Air Vertically Folding Walls Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.

More information

MODEL: STORMMAX-MSD-FG-5100-WET

MODEL: STORMMAX-MSD-FG-5100-WET MODEL: STORMMAX-MSD-FG-5100-WET MEDIUM STILE HURRICANE RESISTANT DOORS WITH FG-5000 FRAMES MONOLITHIC LAMINATED GLASS - DRY GLAZED O.H.C.C H6333 HD6184 MID-PANEL HD6186 MEETING STILES VD6145 JAMB V6331

More information

Theut Company LLC 1317 Bus. Hwy 71 N Columbus, Tx Ph. (979) Fax (979)

Theut Company LLC 1317 Bus. Hwy 71 N Columbus, Tx Ph. (979) Fax (979) Theut Company LLC 1317 Bus. Hwy 71 N Columbus, Tx 78934 Ph. (979) 732-2201 Fax (979) 732-2311 Westside Montessori School Building B Addition Environments, Inc Drymalla Construction February 14, 2013 Installation

More information

YES 600 Thermal Clip Storefront System Installation Manual

YES 600 Thermal Clip Storefront System Installation Manual Installation Manual 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii Frame Types............................................

More information

YES 40 FS/FI Storefront System Installation Manual

YES 40 FS/FI Storefront System Installation Manual Installation Manual 2014 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION YES 40 FS Framing Members... Page 1 YES 40

More information

YHS 50 FS Storefront System & Model 35H/50H Door Installation Manual

YHS 50 FS Storefront System & Model 35H/50H Door Installation Manual Installation Manual 2014 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION YHS 50 Framing Members... Page 1 YHS 50 Accessories...

More information

MODEL: STORMMAX-MSD-FG-5000-WET

MODEL: STORMMAX-MSD-FG-5000-WET MODEL: STORMMAX-MSD-FG-5000-WET MEDIUM STILE HURRICANE RESISTANT DOORS WITH FG-5000 FRAMES MONOLITHIC LAMINATED GLASS - WET GLAZED OHSC H6331 O.H.C.C H6333 MID-PANEL MEETING STILES HD6184 HD6186 VD6145

More information

Curtain Wall Installation Guide

Curtain Wall Installation Guide Curtain Wall Installation Guide Curtain Wall Installation Guide 1 IMPORTANT NOTICES! Important Notices & Information Manufacturer s Notes: The building envelope must be correctly prepared with weather

More information

YES 45 FS/FI Storefront System Installation Manual

YES 45 FS/FI Storefront System Installation Manual Installation Manual 2014 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION YES 45 FS Framing Members... Page 1 YES 45

More information

BuildingEnvelope Oldcastle ( ) -

BuildingEnvelope Oldcastle ( ) - BuildingEnvelope 1-866-Oldcastle (653-2278) - www.obe.com RELIANCE -LT CURTAIN WALL 2" X 7-1/2" / POLYAMIDE PRESSURE PLATE / 1" GLAZING Elev-Reliance-LT-750-PolyPP H0042-Steel-Anchor H5021-ShrBlk-Anchors

More information

INSTALLATION INSTRUCTIONS 2 1/2 x 7 for 1 Glass

INSTALLATION INSTRUCTIONS 2 1/2 x 7 for 1 Glass INSTALLATION INSTRUCTIONS 2 1/2 x 7 for 1 Glass Captured System 3010 Rice Mine Road, Tuscaloosa, Alabama 35406 1-800-772-7737 Fax 1-800-443-6261 www.coralind.com A Division of Coral Industries, Inc. B.G.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 900 SERIES RIBBON WINDOW INSTALLATION INSTRUCTIONS 3056 Walker Ridge Dr. NW, Suite G Walker, MI 49544 800-866-2227 November 2016 www.tubeliteinc.com Page 1 TABLE OF CONTENTS GENERAL CONSTRUCTION NOTES...3-4

More information

Sun Control-Solar Eclipse-Solar Shelf

Sun Control-Solar Eclipse-Solar Shelf Sun Control-Solar Eclipse-Solar Shelf Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! TABLE OF CONTENTS GENERAL INFORMATION Product Use...Page 3 Protection and Storage...Page

More information

Table of Contents. Typical elevation & cut lengths. General construction notes. General installation notes. Typical jamb assembly

Table of Contents. Typical elevation & cut lengths. General construction notes. General installation notes. Typical jamb assembly c CD $ a c Q / / Table of Contents Page Description 1 Parts list 2 3 4 5 6 Typical elevation & cut lengths General construction notes General installation notes Typical jamb assembly Typical intermediate

More information

Frameless Inline Door QCI5288

Frameless Inline Door QCI5288 Frameless Inline Door QCI5288 QCI5288 Rev. 0 Page 1 Date Certified: 06/21/2016 Tools: To install your New Shower Enclosure, you may need the following: Pencil Drill Hack Saw Low Tack Tape 1/8 & 3/16 Drill

More information

Please read and understand all instructions before beginning. These instructions cover impact and non-impact aluminum French Door 650/750.

Please read and understand all instructions before beginning. These instructions cover impact and non-impact aluminum French Door 650/750. The performance and proper operation of a door is only as good as the installation. By following these instructions, the probability of a good installation greatly increases. Please read and understand

More information

YES 45 XT High Performance Thermal Storefront System

YES 45 XT High Performance Thermal Storefront System Dual Thermal Barrier ThermaBond Plus Pour & Debridge Technology Installation Manual 2015 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page

More information

Series Sloped glazed Curtain wall. Installation Instructions

Series Sloped glazed Curtain wall. Installation Instructions Series 5600 Sloped glazed Curtain wall Installation Instructions Part NO. Y308 February 2013 SECTION TABLE OF CONTENTS PAGE I. General Notes & Guidelines. 3-4 II. Gutter and Mullion Assembly.. 5 III. End

More information

YCW 750 OG Outside Glazed Curtain Wall System Installation Manual

YCW 750 OG Outside Glazed Curtain Wall System Installation Manual YCW 750 OG Outside Glazed Curtain Wall System Installation Manual 2012 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION

More information

Phone # La Jolla Doors. Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels

Phone # La Jolla Doors. Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels Phone # 800-440-8785 www.lajolladoors.com La Jolla Doors Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels Thank you for choosing La Jolla Doors In this manual you will

More information

ICU TRACKLESS SLIDING DOOR

ICU TRACKLESS SLIDING DOOR Interior View 0 Installation Instructions Tools Required: Screwdrivers Small Straight (Flat Blade) - for Terminal Block wiring # Phillips (Crosspoint) - for various #8, #0, and #4 screws Wrenches / Sockets

More information

350/500 Heavy Wall TM IR Entrances

350/500 Heavy Wall TM IR Entrances SEPTEMBER, 207 FEATURES Hurricane Resistant Product Blast Mitigation Product Features 50 Heavy Wall TM IR medium stile has vertical stiles, top and 6-/ (65.) bottom rails 500 Heavy Wall TM IR wide stile

More information

INSTALLATION INSTRUCTIONS. Unit No. 126, 726 Classic Pivot Panel/Door/Panel Shower Enclosure

INSTALLATION INSTRUCTIONS. Unit No. 126, 726 Classic Pivot Panel/Door/Panel Shower Enclosure INSTALLATION INSTRUCTIONS Unit No. 126, 726 Classic Pivot Panel/Door/Panel Shower Enclosure QCI0027 Rev. 0 Page 1 of 10 Certified 11/07/2006 MAINTENANCE: Two primary materials are used to manufacture your

More information

YOW 225 TU Window System

YOW 225 TU Window System ThermaBond Plus Poured & Debridged Technology YOW 225 TU SYSTEM DESCRIPTION YOW 225 TU PERFORMANCE FEATURES 2-1/4 Overall Depth ThermaBond Plus Poured & Debridged Thermal Break Variations: Casement, Projected

More information

Installation Instructions

Installation Instructions Installation Instructions 1293 N. Harvey Mitchell Pkwy. Bryan, Texas 77803 800.444.1444 ph 979.823.1005 fax www.aswcommercial.com Simplifying Windows Complete Architectural CD Binder Inside B l as t I

More information

Vinyl Sliding Glass Door Assembly Instructions

Vinyl Sliding Glass Door Assembly Instructions Vinyl Sliding Glass Door Assembly Instructions SERIES SGD 5470/5570 Para instrucciones en español, visite: http://bit.ly/pgtassemblyinstructions Parts List ITEM 4 5 6 7 8 9 0 4 5 6 7 8 SGD 5470/5570 PARTS

More information

Series Advanced and alternate. Installation Instructions

Series Advanced and alternate. Installation Instructions Series 5500 Advanced and alternate Installation Instructions Part NO. Y557 February 2013 TABLE OF CONTENTS SECTION S-5500 ADVANCED INSTALLATION INSTUCTIONS PAGE I. General Notes and Guidelines...... 3-4

More information

YWE 40 T Window Wall System Installation Manual

YWE 40 T Window Wall System Installation Manual Installation Manual 2005 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii Frame Types............................................

More information

Installation Instructions

Installation Instructions Installation Instructions 400 Series Curtainwall 3056 WALKER RIDGE DR. NW, SUITE G WALKER, MI 49544 800-866-2227 dependable@tubeliteinc.com Revised September 2014 dependable@tubeliteinc.com Page 1 TABLE

More information

2.01 Standard Entrances Description

2.01 Standard Entrances Description 2.01 Standard Entrances Description Description Tubelite Standard Entrances have an outstanding reputation for craftsmanship and strength. The Narrow Stile Door has a face dimension of 2 1/8" and is designed

More information

SERIES CF450 INSTALLATION INSTRUCTIONS. SERIES CF450 1¾ x 4½ - B1. Fabrication for Panel Assembly. High Performance Non-Thermal Storefront System

SERIES CF450 INSTALLATION INSTRUCTIONS. SERIES CF450 1¾ x 4½ - B1. Fabrication for Panel Assembly. High Performance Non-Thermal Storefront System SERIES CF450 INSTALLATION INSTRUCTIONS Fabrication for Panel Assembly High Performance Non-Thermal Storefront System Effective October 2014 www.cardcompro.com 1 2 www.cardcompro.com Effective October 2014

More information

Series 955 Tech Set storefront. Installation Instructions

Series 955 Tech Set storefront. Installation Instructions Series 955 Tech Set storefront Installation Instructions Part NO. Y008 February 2013 TABLE OF CONTENTS SECTION PAGE I II III GENERAL NOTES AND GUIDELINES 1-2 PARTS IDENTIFICATION 3-5 DRILL JIGS 6-7 DRILL

More information

Series 406 storefront. Installation Instructions

Series 406 storefront. Installation Instructions Series 406 storefront Installation Instructions Part NO. Y016 February 2013 Series 406 Installation Instructions TABLE OF CONTENTS Section I GENERAL NOTES Page 1 II PARTS IDENTIFICATION Page 2-3 III FABRICATION

More information

Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! May 2015

Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! May 2015 Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! May 2015 Phone: 1-866-OLDCASTLE (653-2278) Web Address: www.oldcastlebe.com S E R I E S 6 0 0 0 X T - S T O R E F R O N T I

More information

western window systems westernwindowsystems.com installation instructions non-pocket 2-1/4 panels

western window systems westernwindowsystems.com installation instructions non-pocket 2-1/4 panels series 2600 multi-slide non-pocket 2-1/4 panels windowsystems.com windowsystems.com movement, which can cause warping and other problems. Frame kit components: Each door will have a head assembly, a threshold

More information

INSTALLATION INSTRUCTIONS FOR PLASCORE NARROW STILE DOORS

INSTALLATION INSTRUCTIONS FOR PLASCORE NARROW STILE DOORS INSTALLATION INSTRUCTIONS FOR PLASCORE NARROW STILE DOORS The following information is provided by Plascore, Inc., as a general guideline for the installation of the Plascore Narrow Stile Door and Jamb

More information

Horizontal Cable Systems

Horizontal Cable Systems ALUMINUM RAILING INSTALLATION INSTRUCTIONS Horizontal Cable Systems 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. 1A) Coastal applications: Confirm

More information

YHS 50 TU Storefront System & Model 35H Door Installation Manual

YHS 50 TU Storefront System & Model 35H Door Installation Manual Installation Manual 2012 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION YHS 50 TU Framing Members... Page 1 YHS 50

More information

INSTALLATION INSTRUCTIONS TRIFAB VG SCREW SPLINE ASSEMBLY TRIFAB VG 450 TRIFAB VG 451 TRIFAB VG 451T

INSTALLATION INSTRUCTIONS TRIFAB VG SCREW SPLINE ASSEMBLY TRIFAB VG 450 TRIFAB VG 451 TRIFAB VG 451T INSTALLATION TRIFAB VG SCREW SPLINE ASSEMBLY TRIFAB VG 450 TRIFAB VG 451 TRIFAB VG 451T INSTRUCTIONS LITHO IN U.S.A. JANUARY KAWNEER COMPANY, INC., 2004 451-VG-970.01.04a PART NO. 451-VG-970 1 INSTALLATION

More information

ICU TRACK SLIDING DOOR

ICU TRACK SLIDING DOOR Interior View 0 Installation Instructions Tools Required: Screwdrivers Small Straight (Flat Blade) - for Terminal Block wiring # Phillips (Crosspoint) - for various #8, #0, and # screws Wrenches / Sockets

More information

Series D200 Narrow Stile Series D300 Medium Stile * D500 Wide Stile ** Standard Aluminum Swing Entrance Doors

Series D200 Narrow Stile Series D300 Medium Stile * D500 Wide Stile ** Standard Aluminum Swing Entrance Doors E F C O C O R P O R A T I O N Visit us on the web at efcocorp.com IMPACT GRADE BALLISTIC GRADE Series D200 Narrow Stile Series D300 Medium Stile * D500 Wide Stile ** Manufacturer Configurations Narrow

More information

Flushglaze For Framed Openings and Horizontal Panels. Window System Installation Guide

Flushglaze For Framed Openings and Horizontal Panels. Window System Installation Guide Flushglaze 4500 For Framed Openings and Horizontal Panels Window System Installation Guide January 2017 BENCHMRK Welcome to Kingspan, global leaders in the design and manufacture of insulated metal panels

More information

**MOUNTING YOUR MONITOR

**MOUNTING YOUR MONITOR FPP72V200 72 FREE STANDING DISPLAY CART Assembly Instructions Hardware List Ref. Qty. Part No. Description AA 4 030-1128 1/4-20 UNC, 1 3/4 Socket Hd Screws BB 1 030-1129 5/8-11 UNC 1 3/4 Socket Hd Screw

More information

SECTION C1 INSTALLATION INSTRUCTIONS

SECTION C1 INSTALLATION INSTRUCTIONS SECTION C1 SERIES CWW451T THERMALLY BROKEN FRONT GLAZED WINDOW WALL / STOREFRONT SYSTEM X 4 1 / for 1" GLAZING INSTALLATION INSTRUCTIONS EXTERIOR GLAZED Effective October 2014 www.cardcompro.com 1 INTERIOR

More information

Series 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing)

Series 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing) Series 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing) Things to Know Before You Start Things to Know Before You Start Removal of Old Fenestration Products Ensure any old fenestration

More information

Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! FEBRUARY 2012

Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! FEBRUARY 2012 Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! Phone: 1-866-OLDCASTLE (653-2278) Web Address: www.oldcastlebe.com FG-1000 & FG-2000 INSTALLATION & GLAZING INSTRUCTIONS These

More information

SERIES CF451T INSTALLATION INSTRUCTIONS. SERIES CF451T 2 x 4½ - B2. Fabrication for Panel Assembly. High Performance Thermal Storefront System

SERIES CF451T INSTALLATION INSTRUCTIONS. SERIES CF451T 2 x 4½ - B2. Fabrication for Panel Assembly. High Performance Thermal Storefront System SERIES CF451T INSTALLATION INSTRUCTIONS Fabrication for Panel Assembly High Performance Thermal Storefront System Effective October 2014 www.cardcompro.com 1 2 www.cardcompro.com Effective October 2014

More information

SERIES 2100/2200 CURTAIN WALL

SERIES 2100/2200 CURTAIN WALL INSTALLATION INSTRUCTIONS SERIES 2100/2200 CURTAIN WALL Phone: (800) 262-5151 Fax: (866) 262-3299 crlaurence.com usalum.com crl-arch.com 11M0173 HANDLING, STORAGE, AND PROTECTION OF The following precautions

More information

INSTALLATION MANUAL STOREFRONT DOORS

INSTALLATION MANUAL STOREFRONT DOORS INSTALLATION MANUAL STOREFRONT DOORS www.aluflam-usa.com SYSTEM DESCRIPTION - Extruded and filled aluminum framing, tested and approved by UL - 3-3/8 frame depth - Clear, fire-rated safety glazing - Door

More information

Versatrac R-System Stock Extrusions, Clips and Accessories

Versatrac R-System Stock Extrusions, Clips and Accessories Versatrac R-System Extrusions are available in 300 series (for 3 3/4" walls) and 400 series (for 4 7/8" walls). Standard finishes are Satin Metallic Bronze, Satin Black, Satin White Baked Enamel, and Clear

More information

Series 526 Thermal impact storefront. Installation Instructions

Series 526 Thermal impact storefront. Installation Instructions Series 526 Thermal impact storefront Installation Instructions Part NO. Y021 February 2013 TABLE OF CONTENTS SECTION PAGE I. General Notes and Guidelines. 3 II. Parts Identification Chart.......4-8 III.

More information

ESA-100 Fixed Sidelite/Non Breakout

ESA-100 Fixed Sidelite/Non Breakout /Non Breakout Exterior View Installation Instructions For use with ESA II Controller 1 Tools Required: Suggested Fasteners Required - (Not supplied) Screwdrivers Small Straight (FlatBlade) - for Terminal

More information

ProLine PL60 HEAVY FRAMELESS BYPASS BATH ENCLOSURE

ProLine PL60 HEAVY FRAMELESS BYPASS BATH ENCLOSURE INSTALLATION INSTRUCTIONS ProLine PL60 HEAVY FRAMELESS BYPASS BATH ENCLOSURE Copyright Alumax Bath Enclosures 2013. All rights reserved. G03980847 5-1-13 !WARNINGS! INSTALLATION WARNINGS a) Alumax Bath

More information

YVS 400 TU Window System

YVS 400 TU Window System YVS 400 TU SYSTEM DESCRIPTION YVS 400 TU PERFORMANCE FEATURES 4 Overall Depth ThermaBond Plus Poured & Debridged Thermal Break Variations: Single Hung, Double Hung & Fixed Windows 1 /8 & 1 1 /16 Glazing

More information

SECTION B INDEX STOREFRONT FRAMING SYSTEMS

SECTION B INDEX STOREFRONT FRAMING SYSTEMS SECTION B INDEX STOREFRONT FRAMING SYSTEMS B PAGE DESCRIPTION 01 STOREFRONT FRAMING SPECIFICATIONS 02 175 SERIES 1 3/4" (44.5) X 4 1/2" (114.3) FLUSH GLAZE FRAMING FOR SINGLE GLAZING. 06 200 SERIES 2"

More information

Versatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series

Versatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series Versatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series TM Rough opening width (finished opening width plus 9/16") Notch for top track units (used as frame header) Rough opening height

More information

YSG 40/50/50T Window Wall System Installation Manual

YSG 40/50/50T Window Wall System Installation Manual Installation Manual 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii PARTS DESCRIPTION YSG 40

More information

C-Series & S-Series Classic Frame with Transom (Single or Pair)

C-Series & S-Series Classic Frame with Transom (Single or Pair) 1. TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Safety Glasses Screw gun #2 Screwdriver tip #3 Screwdriver tip Philips Head screwdriver (Used to move frame on wall using oval slots on

More information

Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! OCTOBER Phone: OLDCASTLE ( ) Web Address:

Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! OCTOBER Phone: OLDCASTLE ( ) Web Address: Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! TABLE OF CONTENTS General Information............................. Page 2 4 Outside Glaze Non Thermal...............................Page

More information

INSTALLATION INSTRUCTIONS TRIFAB 451UT SCREW SPLINE ASSEMBLY TRIFAB 451UT. AUGUST, 2010 (Part No. 452T-CG-970) EC

INSTALLATION INSTRUCTIONS TRIFAB 451UT SCREW SPLINE ASSEMBLY TRIFAB 451UT. AUGUST, 2010 (Part No. 452T-CG-970) EC AUGUST, 2010 (Part No. 452T-CG-970) EC 97904-31 1 INSTALLATION SCREW SPLINE ASSEMBLY Kawneer Company, Inc., 2010 INSTRUCTIONS 2 TABLE OF CONTENTS (452T-CG-970) AUGUST, 2010 These instructions show the

More information

SERIES 2100/2200 CURTAIN WALL

SERIES 2100/2200 CURTAIN WALL INSTALLATION INSTRUCTIONS SERIES 2100/2200 CURTAIN WALL Phone: (800) 262-5151 Fax: (866) 262-3299 crlaurence.com usalum.com crl-arch.com 11M0173 HANDLING, STORAGE, AND PROTECTION OF The following precautions

More information