Installation Guide for PermaSnap Coping & PermaSnap Plus Coping

Size: px

Start display at page:

Download "Installation Guide for PermaSnap Coping & PermaSnap Plus Coping"

Derek Gardner
6 years ago
Views:

1 Installation Guide for PermaSnap Coping & PermaSnap Plus Coping 4 COMMERCE WAY, ARDEN, NC 8704 USA OMGEDGESYSTEMS.COM

2 Installation Guide for PermaSnap & PermaSnap Plus Coping FM Approved S U ANSI/SPRI/FM4435/ES-1 TESTED Installation Guide Index General Information Coping Diagrams Straight Parapet Installation Radius Parapet Installation Vaulted Parapet Installation Special Condition Installation FACE COPING CONCEAED JOINT SPICE #14 X 1½" UNIVERSA FASTENER, PROVIDED CIP 1½" SS RING SHANK NAI, PROVIDED BOCKING BY OTHERS MEMBRANE BY OTHERS 3/8" AOWANCE NOTES: #1 - Isolate all metal parts from ACQ treated wood or other galvanically incompatible material with appropriate membrane material. # - Appliance attachments, such as lightning rods, signs, or antennae that penetrate the water seal, induce a galvanic reaction, or otherwise compromise the effectiveness of the roof edge system, shall be eliminated or isolated to prevent problems per section 8.0 of ANSI/SPRI/FM4435/ES-1. Appliances shall be isolated from or not attached to the roof edge system. Consult the lightning protection system manufacturer for specific attachment instructions.

3 DO NOT USE SEAANT AT JOINT SPICES COPING CAP CONCEAED JOINT SPICE CIP ING MEMBRANE *3/8" *3/4" PACE FASTENERS IN A PRE-PUNCHED HOES. FACE SIZES 3¼" X < 4¾ " SPICE AND CIP FASTENERS, 1½" 1" min. SS RING SHANK NAIS SUPPIED** PER SMACNA BOCKING BY OTHERS #14 X 1½" UNIVERSA FASTENER, TYP. of (4) Clip = Wall + 3/8" Joint Splice = Wall + 5/8" Cap = Wall + 3/4" *** COPING CAP CONCEAED JOINT SPICE CIP ING MEMBRANE *3/8" *3/4" PACE FASTENERS IN A PRE-PUNCHED HOES. FACE SIZES 4¾" X 1" 1" min. PER SMACNA SPICE AND CIP FASTENERS, 1½" SS RING SHANK NAIS SUPPIED** *** BOCKING BY OTHERS #14 X 1½" UNIVERSA FASTENER, TYP. of (4) Clip = Wall + 3/8" Joint Splice = Wall + 5/8" Cap = Wall + 3/4" *DIMENSION WI VARY WITH WIDTH VARIATION ** 4 TOTA NAIS REQUIRED FOR SECUREMENT ONTO BUIDING, CONTACT OMG EDGESYSTEMS WHEN SUBSTRATE IS OTHER THAN WOOD *** SEE PROFIES BEOW FOR VARYING CIP PROFIES DUE TO SIZE CIP DESIGN FOR S 6" TO 0" WIDE CIP DESIGN FOR S OVER 0" WIDE 3

4 DO NOT USE SEAANT AT JOINT SPICES A STRAIGHT ENGTH CIP SPACING 40" O.C. FOR A SIZES F B (4) FASTENERS PER CIP TOP E (1) UNIVERSA FASTENER PER IN SUPPORT C H G D (4) FASTENERS* PER CIP FOR FACE SIZES GREATER THAN 4¾" * 1½" SS RING SHANK NAIS SUPPIED. CONTACT OMG FOR SUBSTRATES OTHER THAN WOOD. D OUT H () FASTENERS PER OUT SUPPORT IN A. Formed Coping Cap 10-ft. engths B. 6-in. Wide Concealed Joint Splice One (1) at Each Clip ocation C. 1-in. Wide Galv. Steel Clips 40-in. O.C. D. Corner Supports (Inside & Outside) Used to Support Outside and Inside Miters E. #14 x 1½-in. Universal Fasteners Four (4) Per Clip Top F. Splice Fasteners 1½-in. SS Ring Shank Nails Supplied Two () Per FACE G. Clip Fasteners 1½-in. SS Ring Shank Nails Supplied Two () Per FACE H. Corner Support Fasteners Two () #14 x 1½-in. Universal Fasteners Per Outside Corner Support One (1) #14 X 1½-in. Universal Fasteners Per Inside Corner Support 4

5 HOOK FRONT SNAP BACK SPICE FASTENERS CENTER FASTENERS IN SOTS TOP VIEW 40" ON CENTER OUT IN STEP 4: Installing Coping Miters Hook the face of the coping miter over the outside face leg of the clips, rotate the coping miter over the top of the clips and snap the back leg by pressing down until the hook snaps into place (Run fingers on the underside to ensure a static engagement is present). =3 1/4-in. - for wall widths 16-in. wide =9 1/4-in. - for wall widths > 16-in. and 3-in. wide =custom for wall widths > 3-in. wide END CAP FASTENER BY INSTAER SEAANT BY OTHERS STEP 1: Installing Clips at Corners & Along the Parapet ocate all 40-in. on center. Pull clips snugly against the outside face. Place four (4) # 14 x 1½-in. Universal fasteners in the top of the clip. Position the joint splice over the center of the clip aligning the middle two holes, secure using two () 1½-in. ss ring shank nails through the splice and into the substrate. Secure the main clip face with two additional 1½-in. ss ring shank nails into the substrate. Joint splices should be installed at A clip locations. END END TERM CIP NOT SHOWN STEP 5: Installing End Caps and End Terms Install end caps and end terms by hooking face and snapping back into place. End Caps and End Terms must be restrained from moving by securing the end cap/term to the clip using a fastener (by installer) through the back leg of the end cap/term. END COPING STRAIGHT ENGTH STEP : Installing Clips at Wall Ends Install the first clip approximately -in. from the wall end as shown. Install the second clip 4-in. on center from the wall end. (If end cap leg is other than 4-in. adjust clip placement accordingly) COPING MITER OUT IN STEP 3: Installing Corner Supports Two () corner supports are to be placed at all corners to support the cap. Set each clip away from the corner approximately 3-in. Secure outside corner support clips using #14 x 1½-in. Universal fasteners and the inside corner support clips using a #14 x 1½-in. Universal fastener. HOOK FRONT SNAP BACK STEP 6: Installing Coping Straight engths Begin installing from the corners and end conditions working inward to the center. Allow a 1/4-in. gap between the coping sections for thermal expansion. Review lengths of all straight pieces prior to cutting to avoid creating relatively short sections of caps adjacent to full length sections. There should be a clip and joint splice at least every 40-in. O.C. and at every joint. Every fifth (5th) 10-foot section of coping should be secured to the clip using a single fastener (by installer [same procedure as STEP 5]) to isolate movement within a containment zone. 5

6 DO NOT USE SEAANT AT JOINT SPICES RADIUS CIP SPACING 30-in. O.C. FOR A SIZES A F 1½" SS RING SHANK NAI B (4) FASTENERS PER CIP TOP C E (1) UNIVERSA FASTENER PER IN SUPPORT H F D (4) FASTENERS* PER CIP FACE * 1½" SS RING SHANK NAIS SUPPIED. CONTACT OMG FOR SUBSTRATES OTHER THAN WOOD. D OUT RADIUS TO STRAIGHT H () FASTENERS PER OUT SUPPORT IN RADIUS TO STRAIGHT A. Radius Coping Cap 60-ft. engths Typ. (engths May Vary) B. 6-in. Wide Concealed Joint Splice One (1) at Each Clip ocation C. 6-in. Wide Galv. Steel Clip 30-in. on center D. Corner Supports (Inside & Outside) Used to Support Outside and Inside Corners E. #14 x 1½-in. Universal Fasteners Four (4) Per Clip Top F. Splice Fasteners 1½-in. SS Ring Shank Nails Supplied Two () Per FACE G. Clip Fasteners 1½-in. SS Ring Shank Nails Supplied Two () Per FACE H. Corner Support Fasteners Two () #14 x1½-in. Universal Fasteners Per Outside Corner Support One (1) #14 X 1½-in. Universal Fasteners Per Inside Corner Support 6

7 HOOK FRONT SNAP BACK SPICE FASTENERS CENTER FASTENERS IN SOTS 40" ON CENTER OUT IN TOP VIEW STEP 4: Installing Coping Miters Hook the face of the coping miter over the outside face leg of the clips, rotate the coping miter over the top of the clips and snap the back leg by pressing down until the hook snaps into place (Run fingers on the underside to ensure a static engagement is present). 30" O.C. (AS REQUIRED) =3 1/4-in. - for wall widths 16-in. wide =9 1/4-in. - for wall widths > 16-in. and 3-in. wide =custom for wall widths > 3-in. wide END CAP FASTENER (BY INSTAER) END TERM SEAANT BY INSTAER STEP 1: Installing Clips at Corners & Along the Parapet ocate all 30-in. on center. Pull clips snugly against the outside face. Place four (4) # 14 x 1½-in. Universal fasteners in the top of the clip. Position the joint splice over the center of the clip aligning the middle two holes, secure using two () 1½-in. ss ring shank nails through the splice and into the substrate. Secure the main clip face with two additional 1½-in. ss ring shank nails into the substrate. Joint splices should be installed at A clip locations. END CIP NOT SHOWN STEP 5: Installing End Caps and End Terms Install end caps and end terms by hooking face and snapping back into place. End Caps and End Terms must be restrained from moving by securing the end cap/term to the clip using a fastener (by installer) through the back leg of the end cap/term. RADIUS COPING 1/4" OUT IN STEP : Installing Corner Supports Two () corner supports are to be placed at all corners to support the cap. Set each clip away from the corner approximately 3-in. Secure outside corner support clips using #14 x 1½-in. Universal fasteners and the inside corner support clips using #14 x 1-½-in. Universal fasteners. END TERMINATION " " 4" 4" STEP 3: Installing Anchor Clips at Wall Ends Install the first clip approximately -in. from the wall end as shown. Install the second clip 4-in. on center from the wall end. (If end cap leg is other than 4-in. adjust clip placement accordingly.) STEP 6: Installing Radius Coping engths Begin installing from the corners and end conditions working inward to the center. Allow a 1/4-in. gap between coping sections for thermal expansion. Review lengths of all straight pieces prior to cutting to avoid creating relatively short sections of caps adjacent to full length sections. There should be a clip and joint splice at least every 30-in. O.C. and at every joint. Every fifth (5th) 5-foot section of coping should be secured to the clip using a single fastener (by installer [same procedure as STEP 5]) to isolate movement within a containment zone. 7

8 COPING CAP ANCHOR CIP #14 X 1½" UNIVERSA FASTENER, PROVIDED OFFSET 1½" SS RING SHANK NAI Clip = Wall + 3/8" Cap = Wall + 1¼" Wall ING MEMBRANE A B (4) FASTENERS PER CIP C D () FASTENERS PER CIP FACE VAEY Vaulted to Flat Wall Transition Miter A. Vaulted Coping Cap 60-in. engths Typ. (engths May Vary) B. Galvanized Steel Clip 6-in. Wide (Spacing on next page) C. #14 x 1-½-in. Universal Fastener Four (4) Per Clip Two () Per Outside Corner Support One (1) Per Inside Corner Support D. 1-1/-in. SS Ring Shank Nail Two () Per Clip Face 8

9 VAUTED 60" (AS REQUIRED) VAUTED PAN VIEW FAT FAT FACE APPY EQUA PRESSURE STRAIGHT 60" SEE CIP SPACING BEOW EEVATION VIEW (CIP TO CIP) OFFSET OFFSET STEP 3 : Installing Coping Miters Hook the face of the coping miter over the outside face leg of the clips, rotate the coping miter over the top of the clips and snap the back leg by pressing down until the hook snaps into place. Additionally apply equal pressure to font and back of coping to get proper engagement onto clips. (Run fingers on the underside to ensure a static engagement is present). " " 1/4" GAP TYPICA CIP SPACING TYPICA VAUT TO FAT MITER CIP BEOW FACE OF CAP FASTENER (BY INSTAER) END CAP END TERM SEAANT BY INSTAER STEP 1: Installing Clips at Valleys & Along the Parapet ocate clips as shown. Pull clips snugly against the outside face. Place four (4) screw fasteners in the top of the clip with fasteners centered in slots. Place two () ss ring shank nails in the clip face if face is 3¼-in. DO NOT place clip at joint locations, see diagrams above to determine clip locations. ( = 4-in. Typical eg engths) END () CIPS UNDER CAP 19" " 19" " STEP 4: Installing End Caps and End Terms Install end caps and end terms by placing the cap in the correct location over the clips. Apply even pressure on both legs of the cap until both legs are fully engaged on clips. End caps/terms must be restrained from moving by securing the end cap/term to the clip using a fastener (by installer) through the back leg of the end cap/term. END 1/4" 1/4" PAN VIEW 19" " PAN VIEW TERMINATION 19" " OFFSET OFFSET TOP OF VAUT EEVATION VIEW EEVATION VIEW END EEVATION VIEW STEP : Installing Clips at Wall Ends Install the first clip approximately -in. from the wall end as shown. Install the second clip 19-in. on center from the wall end. DO NOT place second clip at joint location. (If end cap leg is other than 30-in. adjust clip placement accordingly.) Install third clip 7-in. from second as shown above. STEP 5: Installing Vaulted Coping engths Begin installing from the valleys and the lower most part of the vaults at the wall ends working toward the upper/top of the vault. Allow a 1/4-in. gap between the coping sections for thermal expansion. Review lengths of all vaulted pieces prior to cutting to avoid creating relatively short sections of cap adjacent to full length sections. There should be at least (3) three anchor clips under each coping cap (Clip spacing may vary). Every fifth (5th) 5-ft. section of coping should be secured to the clip using a fastener (by installer [same procedure as STEP 4]) to isolate movement within a containment zone. 9

10 EXAMPE 1 1 CENTER CEATS UNDER CAP ENDS '1' '' EXAMPE WIDE 1 '1' SUPPORTS " ININE TRANSITION NOTE: Instructions are for face leg and back leg offsets. STEPS: 1. Install cleat 1 -in. from offset, only if wide wall cap leg length is longer than 0-in.. Install cleats centered under cap ends. PIER END TRANSITION NOTE: Instructions are for face leg and back leg offsets. STEPS: 1. Install cleat 1 only if '' is longer than 1-in. Else use corner support as shown.. For '1' cleats and corner supports, see below. 3. Install cleats centered under cap ends. '' '1' > 1-in. '1' < 1-in. SUPPORTS Install corner supports as shown in EXAMPE Install cleat as shown in EXAMPE 1 EXAMPE 1 1 '' 1 '1' '' SUPPORTS 'Z' MITER NOTE: Instructions work for face leg on either side. STEPS: 1. Install cleat 1 only if '' is longer than 14-in.. Install cleats centered under cap ends. 3. Install appropriate corner supports in designated areas. '1' EXAMPE PIER ININE TRANSITION NOTE: Instructions are for face leg and back leg offsets. STEPS: 1. Install cleat 1 only if '' is longer than 1-in. Else use corner support as shown.. For '1' procedures see table below. 3. Install cleats centered under cap ends. '' SUPPORTS '1' > 1" '1' < 1" Install corner supports as shown in EXAMPE Install cleat as shown in EXAMPE 1 4 COMMERCE WAY, ARDEN, NC 8704 USA OMGEDGESYSTEMS.COM Copyright 017 OMG, Inc. All rights reserved. Superior productivity. Superior performance. EM1066 Rev

Installation Guide Index

Installation Guide Index Installation Guide for FlintEdge Coping & Coping+ Straight Parapets 6" through Wide ANSI/SPRI ES-1 TESTE Also included: Installation Guides for Radius Parapets 6" through Wide Vaulted Parapets 6" through