Installation Guide for PermaSnap Plus Coping

Size: px

Start display at page:

Download "Installation Guide for PermaSnap Plus Coping"

Cameron Cunningham
5 years ago
Views:

1 Installation Guide for PermaSnap Plus Coping 4 COMMERCE WAY, ARDEN, NC USA OMGEDGESYSTEMS.COM

2 PermaSnap Plus Coping Reference Guide 1. Standard Installation Steps Page Corner Supports Page Coping Clip Page Coping Splice Page Coping Miter Page Coping End Condition Page Coping Straight Section Page 5 2. Accessory Condition Guide Page Inline Miter Conditions Page Pier Miter Conditions Page Tee Miter Conditions Page Ridge Miter Conditions Page Valley Miter Conditions Page Horizontal Zee Miter Conditions Page Vertical Zee Miter Conditions Page Vaulted Conditions Page Radius Conditions Page 14 2

3 STEP 1: BEGIN COPING INSTALLATION AT CORNER LOCATIONS AS SHOWN IN PICTURE BELOW BY INSTALLING CORNER SUPPORTS FLUSH AGAINST THE SUBSTRATE THEN USING #14 X 1-1/2" UNIVERSAL FASTENERS FOR SECUREMENT. OUTSIDE CORNER SUPPORT #14 x 1-1/2" UNIVERSAL FASTENERS (PRE-DRILL W/ 3/16" DRILL BIT FOR MASONRY CONDITIONS) 3" 3" STEP 2: ALIGN CENTER OF EACH CLIP FROM THE CORNER SUCH THAT THE MITER LEG SITS DIRECTLY HALF-WAY OVER EACH CLIP AS SEEN IN STEPS 3 & 4 (PAGE 4) MAINTAIN GAP IF NEEDED, DO NOT TO OVERDRIVE COPING CLIPS (8 FASTENERS PER CLIP) MAGNETIC LEVEL USE LEVEL TO ENSURE BACK LEG IS VERTICAL COPING CLIP BACK LEG MEMBRANE BY OTHERS SUBSTRATE ALIGN CENTER TO END OF MITER ALIGN CENTER TO END OF MITER 3

4 4 STEP 3: LOCATE SPLICES ONTO EACH CLIP, BEING SURE TO REMOVE TAPE FILM FROM EACH CLIP PRIOR TO PLACEMENT. CONCEALED SPLICES OUTSIDE CORNER SUPPORT PEEL TAPE FILM ON ALL CLIPS STEP 4: LOCATE MITER AND PLACE ONE LEG OVER THE CORNER SUPPORT AND CLIP, ROTATE BACKWARD AND PRESS DOWNWARD TO ENGAGE ONTO CLIP, THEN REPEAT ON ADJACENT LEG OF MITER. OUTSIDE MITER OUTSIDE CORNER SUPPORT

5 5 STEP 5: PLACE CLIPS AT END LOCATIONS SHOWN BELOW AND LOCATE END CAPS/END TERMS AND HOOK ON FRONT OF CLIP, ROTATE BACKWARD AND PRESS DOWNWARD TO ENGAGE ONTO CLIP. END CAP END TERM 2" 2" NOTE: ALL MITERS, END CONDITIONS, AND ACCESSORY CONDITIONS SHOULD BE INSTALLED PRIOR TO STRAIGHT SECTIONS STEP 6: AFTER ALL CORNER AND END CONDITIONS ARE INSTALLED, USE TABLE BELOW TO INSTALL STRAIGHT SECTIONS, CUTTING DOWN AND ADJUST SPACING AS NEEDED. (DO NOT CUT CORNERS AND END CONDITIONS, USE STRAIGHT SECTIONS FOR ADJUSTMENTS. STRAIGHT SECTION 1/4" GAP 1/4" GAP SEE TABLE Clip Spacing = 30" On Center - for wall size 24" Clip Spacing = 24" On Center - for wall size > 24"

6 6 PermaSnap Plus Coping Accessory Conditions Reference Inline Miter Conditions (Page 7) Pier Miter Conditions (Page 8) Tee Miter Conditions (Page 9) Ridge Miter Conditions (Page 10) Valley Miter Conditions (Page 10) Horizontal Zee Miter Conditions (Page 11) Vertical Zee Miter Conditions (Page 12) Vaulted Conditions (Page 13) Radius Conditions (Page 14)

7 7 INLINE MITER CONDITIONS AFTER INSTALLING MITER AND END LOCATIONS, CONTINUE INSTALLATION AT TRANSITION SECTIONS FIRST, BEING SURE CLIPS ARE LOCATED AT JOINTS AND SPACED ACCORDING TO THE CHART IN STEP 6. THEN CONTINUE TO INSTALL STRAIGHT SECTIONS. INLINE MITER END CAP INLINE MITER STRAIGHT SECTION (FIELD CUT TO FIT) 2" ALIGN CENTER OF CLIP TO LENGTH OF END CAP LOCATE AT JOINT 1/4" GAP SEE CHART AFTER HOOKING COMPONENTS ONTO CLIP SECTIONS AND ROTATING BACKWARDS TO SNAP ONTO CLIP, USE GAP TOOL TO ENSURE ALL JOINTS ARE A MINIMUM OF 1/4" AND THAT ALL SCRATCHES ARE COVERED UP USING TOUCH-UP PAINT. STRAIGHT SECTION (FIELD CUT TO FIT) 1/4" 1/4" 1/4" GAP GAP GAP 1/4" GAP

8 8 PIER MITER CONDITIONS LOCATE OUTSIDE CORNER SUPPORT AT OUTSIDE PIER LOCATION FIRST. PROCEED WITH LOCATING CENTER OF CLIP/SPLICES AT END OF EACH MITER LEG. HOOK ONTO FRONT OF CORNER SUPPORT AND COPING CLIP, ROTATE BACKWARD ONTO CLIP AND PUSH DOWNWARD TO ENGAGE CAP ONTO CLIP, THEN PROCEED WITH ADJACENT LEG. PIER MITER OUTSIDE CORNER SUPPORT NOTE: ALL MITERS, END CONDITIONS, AND ACCESSORY CONDITIONS SHOULD BE INSTALLED PRIOR TO STRAIGHT SECTIONS PIER MITER OUTSIDE CORNER SUPPORT

9 9 TEE MITER CONDITIONS LOCATE CENTER OF CLIP/SPLICES AT END OF EACH MITER LEG. HOOK ONTO FRONT OF COPING CLIPS WHICH ARE IN-LINE FIRST, ROTATE BACKWARD ONTO CLIP AND PUSH DOWNWARD TO ENGAGE CAP ONTO CLIP, THEN PROCEED WITH ADJACENT LEG. TEE MITER NOTE: ALL MITERS, END CONDITIONS, AND ACCESSORY CONDITIONS SHOULD BE INSTALLED PRIOR TO STRAIGHT SECTIONS TEE MITER

10 10 RIDGE MITER CONDITIONS & VALLEY MITER CONDITIONS START INSTALLATION AT CORNER OR END CONDITIONS (SHOWN BELOW). LOCATE CLIPS AT END CONDITIONS AND SECURE TO SUBSTRATE AS SHOWN, BE SURE TO FOLLOW STEPS 5 (PAGE 5) FOR INSTALLATION. FOR VALLEY MITERS, LOCATE CLIPS AT JOINTS (NO SPLICE REQUIRED FOR SLOPED WALLS AS SHOWN BELOW). LOCATE RIDGE MITER NEXT, BE SURE TO LOCATE CENTER OF CLIPS TO ALIGN WITH END OF RIDGE MITER (NO SPLICE REQUIRED FOR SLOPED WALLS AS SHOWN BELOW). ADJUST OFFSET CAP LENGTHS (DO NOT CUT FROM OFFSET TAB SIDE) TO FIT IN BETWEEN MITER AND END CONDITIONS ON SLOPED WALLS. USING SPACING CHART FOR CLIPS AS SHOWN BELOW. OFFSET CAP (CUT TO LENGTH) END CAP RIDGE MITER OFFSET CAP (CUT TO LENGTH) SLOPED WALL CONDITION END CAP VALLEY MITER ALIGN CENTER OF CLIP TO LENGTH OF MITER. SEE CHART FOR OFFSET CAP ALIGN CENTER OF CLIP TO LENGTH OF END CAP 2" SEE SPACING CHART FOR OFFSET CAP (CUT TO LENGTH) SLOPED WALL CONDITION 2" ALIGN CENTER OF CLIP TO LENGTH OF END CAP Clip Spacing = 30" On Center - for wall size 24" Clip Spacing = 24" On Center - for wall size > 24" NOTE: ALL MITERS, END CONDITIONS, AND ACCESSORY CONDITIONS

11 11 HORIZONTAL ZEE MITER CONDITIONS LOCATE CORNER SUPPORTS AT OUTSIDE AND INSIDE CORNER LOCATIONS FIRST. NEXT LOCATE MIDDLE CLIP IN CENTER OF MIDDLE LEG OF ZEE MITER (IF SPACE ALLOWS). PROCEED WITH LOCATING CENTER OF CLIP/SPLICES AT END OF EACH MITER LEG. HOOK ONTO FRONT OF CORNER SUPPORT AND COPING CLIP, ROTATE BACKWARD ONTO CLIP AND PUSH DOWNWARD TO ENGAGE CAP ONTO CLIP, THEN PROCEED WITH ADJACENT LEG. HORIZONTAL ZEE MITER INSIDE CORNER SUPPORT 3" OUTSIDE CORNER SUPPORT 3" ALIGNCENTEROFCLIP TO LEGLENGTH NOTE: ALL MITERS, END CONDITIONS, AND ACCESSORY CONDITIONS SHOULD BE INSTALLED PRIOR TO STRAIGHT SECTIONS

12 12 VERTICAL ZEE MITER CONDITIONS LOCATE CENTER OF CLIP/SPLICES AT END OF EACH MITER LEG. HOOK ONTO FRONT OF COPING CLIP, ROTATE BACKWARD ONTO CLIP AND PUSH DOWNWARD TO ENGAGE CAP ONTO CLIP, THEN PROCEED WITH ADJACENT LEG. VERTICAL ZEE MITER ALIGN CENTER OF CLIP TO LENGTH OF MITER ALIGN CENTER OF CLIP TO LENGTH OF MITER NOTE: ALL MITERS, END CONDITIONS, AND ACCESSORY CONDITIONS SHOULD BE INSTALLED PRIOR TO STRAIGHT SECTIONS

13 13 RADIUS CONDITIONS LOCATE CORNER SUPPORTS AT OUTSIDE AND INSIDE CORNER LOCATIONS FIRST. NEXT LOCATE CLIPS AT END LOCATIONS AS SHOWN IN STEP 5 (PAGE 5). PROCEED WITH LOCATING CENTER OF CLIP/SPLICES AT END OF EACH MITER LEG. HOOK ONTO FRONT OF CORNER SUPPORT AND COPING CLIP, ROTATE BACKWARD ONTO CLIP AND PUSH DOWNWARD TO ENGAGE CAP ONTO CLIP THEN PROCEED WITH ADJACENT LEG. FINALLY LOCATE ADDITIONAL CLIPS SPACED AT 20" ON CENTER FOR RADIUS SECTION (CUT AS NEEDED) SECURE CAP ONTO CLIPS BY PUSHING CAPS STRAIGHT DOWN SO THAT SPRINGS ALLOW FOR CAPS TO SECURE ONTO CLIPS. RADIUS TO STRAIGHT MITER STRAIGHT SECTION RADIUS SECTION END CAP RADIUS TO STRAIGHT MITER INSIDE CORNER SUPPORT 3" COPING CLIP & SPLICE OUTSIDE CORNER SUPPORT 3" RADIUS COPING CLIP & SPLICE 20" ON CENTER RADIUS COPING CLIP & SPLICE COPING CLIP & SPLICE COPING SPLICE FRONT SPRING COPING CLIP BACK SPRING #14 X 1-1/2" UNIVERSAL FASTENER RADIUS CLIP/SPLICE PROFILE VIEW NOTE: ALL MITERS, END CONDITIONS, AND ACCESSORY CONDITIONS SHOULD BE INSTALLED PRIOR TO STRAIGHT SECTIONS

14 14 VAULT CONDITIONS LOCATE CENTER OF CLIPS AT END OF MITER LEGS FIRST. PROCEED WITH INSTALLING CLIPS PER STEP 5 (PAGE 5), HOOK CAP ROTATE BACKWARD ONTO CLIP AND PUSH DOWNWARD TO ENGAGE CAP ONTO CLIP. FINALLY LOCATE VAULT CLIPS AT 20" ON CENTER (NO SPLICES REQUIRED). SECURE CAP ONTO CLIPS BY PUSHING CAPS STRAIGHT DOWN SO THAT SPRINGS ALLOW FOR CAPS TO SECURE ONTO CLIPS. ADJUST VAULT CAP LENGTHS (DO NOT CUT FROM OFFSET TAB SIDE) TO FIT IN BETWEEN MITER AND END CONDITIONS ON SLOPED WALLS. USING SPACING CHART FOR CLIPS AS SHOWN BELOW. VAULT SECTION VAULT TO STRAIGHT MITER VAULT CLIP END CAP 20" ON CENTER COPING CLIP & SPLICE ALIGN CENTER OF CLIP TO LENGTH OF MITER LEG ALIGN CENTER OF CLIP TO LENGTH OF END CAP FRONT SPRING COPING CLIP #14 X 1-1/2" UNIVERSAL FASTENER BACK SPRING 2" VAULT CLIP PROFILE VIEW NOTE: ALL MITERS, END CONDITIONS, AND ACCESSORY CONDITIONS SHOULD BE INSTALLED PRIOR TO STRAIGHT SECTIONS

15 15 NOTES Disclaimer: OMG Edge Systems has performed testing in accordance with ANSI/SPRI/FM4435/ES-1 any deviation from the system as intended may void warranty claims. The systems are designed independent from any other building material/product if another material/product is used in conjunction with an OMG Edge Systems product this will nullify the warranty. Please contact OMG for assistance at

Installation Guide for PermaSnap Coping & PermaSnap Plus Coping

Installation Guide for PermaSnap Coping & PermaSnap Plus Coping 4 COMMERCE WAY, ARDEN, NC 8704 USA 800.89.9173 88.676.1700 OMGEDGESYSTEMS.COM Installation Guide for PermaSnap & PermaSnap Plus Coping FM