INSTALLATION INSTRUCTIONS Aluminum Railing System
|
|
- Jeffry Thornton
- 6 years ago
- Views:
Transcription
1 INSTALLATION INSTRUCTIONS FASCIA MOUNT SURFACE MOUNT OFFSET BASE SURFACE MOUNT STANDARD BASE CORE MOUNT Ø3" [Ø76 mm] " [89 mm] " [32 mm] " [73 mm] 200 SERIES 300 SERIES " [95 mm] 5" [127 mm] 2" [52 mm] " [44 mm] 350 SERIES 400 SERIES 3 4 " [19 mm] 3 4 " [19 mm] " [44 mm] " [44 mm] BOTTOM RAIL GLASS BOTTOM RAIL PICKET R2 2 1 " [R63 mm] 2" [51 mm] 1" [25 mm] " [44 mm] " [48 mm] 100 SERIES TOP RAIL 100 SERIES BOTTOM RAIL - COPYRIGHT C.R.LAURENCE CO., INC Page 1 of 12 1M
2 Vertical Post Kits: C.R. Laurence Co., Inc. offers various types of mountings for securing Posts. Surface mount (Standard Base). This is the most popular type of mounting. The Post is connected to a 5 (127 mm) square base, which is mounted to the floor. Surface mount (Offset Base) The Post is offset on the base to allow the post to be flush against a wall or aligned with a vertical face. Fascia Mount This mount allows the Post to be mounted to the vertical face of a wall or slab. Core Mount This method of mounting requires coring a hole in the floor, installing the Post and filling the hole with Kwixset Cat. No. KWK50 Cement. FASCIA MOUNT SURFACE MOUNT OFFSET BASE SURFACE MOUNT STANDARD BASE CORE MOUNT Post assembly and installation Surface mounted Posts. Assemble the Base Plate to the Post with the (6) ¼ (6 mm) x 1-½ (38 mm) Cat. No. BPS112 screws provided. Position the included Moisture Barrier Gasket between the substrate and the base plate prior to mounting. Helpful Hints: Lubricate the screws and assembly will be much easier. 2 3/8" Top Rail Direction BASE PLATE SCREWS ISOLATOR PAD BASE PLATE When surface mounting ARS Posts, make sure that the 3-hole edges on the Base Plates run the same direction as the Top Rail, whenever possible, for maximum rigidity. Page 2 of 12 1M
3 When installing Posts, start with the outside or corner Posts first. Make sure they are plumb and level then install the intermediate Posts. Helpful Hints: Make sure you put the special cup washer under the bolt before driving it in. This washer is used to secure the bolt cover button. ANCHOR BOLT CUP WASHER PART # WSHR1 BASE PLATE ISOLATOR PAD FINISHED FLOOR COVER BUTTONS PART # BTN1 CUP WASHER PART # WSHR1 BASE PLATE ISOLATOR PAD FINISHED FLOOR Fascia Mounted Posts. Place Moisture Barrier Gaskets to the Fascia Brackets. Attach the Fascia Brackets to the fascia. Start with the outside or corner Brackets first, then install the intermediate Brackets. Once the Bracket is secured, screw the Base Plate onto the Bracket. Then lower the Post into the Bracket and secure it to the Base Plate with screws provided. Helpful Hints: Lubricate the screws and assembly will be much easier. MOISTURE BARRIER GASKETS (2) FASCIA BRACKET ANCHOR BOLT (4) CUP WASHER CAT.NO. WSHR1 (4) COVER BUTTONS CAT. NO. BTN1 (4) BASE PLATE #14 X 1 1/2"(38 mm) F/H SCREW (6) Page 3 of 12 1M
4 Core Mounted Posts: Core hole a minimum of 4 (102 mm) Diameter X 6 (152 mm) deep. Install the Post. Secure Post plumb and level, then fill cavity with Kwixset Cat. No. KWX50 Cement. Start with the outside or corner Posts. Then install the intermediate Posts. Top Caps C.R. Laurence has a number of Top Caps available offering a selection of appearances and applications. 100 Series offers a rectangular section rail with a crowned top, which runs between posts. This Top cap is the only one used for stairways and conforms to UBC requirements. 200 Series is a rectangular section Rail that runs continuously across the top of the Posts. 300 Series is a round section Rail that runs continuously across the top of the Posts. 350 Series is an oval section Rail that runs continuously across the top of the Posts. 400 Series is a rectangular section Rail with crowned top, which runs continuously across the top of the Posts. R2 2 1 " [R63 mm] 2" [51 mm] " [89 mm] " [44 mm] " [32 mm] 100 SERIES TOP RAIL 200 SERIES Ø3" [Ø76 mm] " [95 mm] 5" [127 mm] " [73 mm] 2" [52 mm] " [44 mm] 300 SERIES 350 SERIES 400 SERIES Page 4 of 12 1M
5 100 Series Installation Instructions 100 Series Top Cap Installation: Attach the 100 series Top Connector Block Cat. No. RCB1 to the sides of the Posts. Typically the distance from the top of the Post to the first hole is 2-1/4 (57 mm) and 3-1/4 (83 mm) to the lower hole. Helpful Hints: Use the die lines in the Post extrusion as a guide for the holes. This will ensure the Connector Block is centered on the Post. Cut the Top Cap to length. Slide the Top Cap over the Connector Blocks and secure with self-drilling Tek Screws Cat. No. TEK1. Helpful Hints: Use the die line on the bottom leg of the Top Cap extrusion as a guide for the screws. Screws should be approx. ½ (12 mm) from the edge of the Post. Secure the post caps to the top of the posts using silicone adhesive Cat. No. 95C. TOP CAP 2-1/4" (57 mm) CONNECTING BLOCK CAT.NO. RCB1 STANDARD CONNECTING BLOCK POSITION 100 Series Bottom Rail Installation Attach the 100 series Connector Block Cat. No. RCB1 to the sides of the Posts. Typically the distance from the floor to the bottom of the rail is 3 (76 mm). This will give a dimension of 3-3/8 (86 mm) from the floor to the center of the lower holes in the block. Helpful Hints: Use the Die lines in the Post extrusion as a guide for the holes. This will ensure the Connector Block is centered on the Post. Cut the Bottom Rail to length. Slide the Rail over the Connector Blocks and secure with self-drilling Tek Screws Cat. No. TEK1. Helpful Hints: Use the die line on the bottom leg of the Bottom Rail extrusion as a guide for the Screws. Screws should be approx. ½ (12 mm) from the edge of the Post. CONNECTING BLOCK RCB1 BASE PLATE ISOLATOR PAD " STANDARD CONNECTING BLOCK POSITION Page 5 of 12 1M
6 100 Series Glass Installation Install two Spacer Blocks into Bottom Rail. One at each end, 3 (76 mm) from edge of Post. Cut vinyl the same length as the Rails. Push fit into the Rails. TOP CAP TOP RAIL TOP VINYL TOP VINYL INSTALLATION BOTTOM VINYL BOTTOM RAIL SPACER BLOCK BASE PLATE ISOLATOR PAD BOTTOM VINYL INSTALLATION Glass size is determined by the daylight opening. Height: Daylight Opening plus 3/4 (19 mm). Width: Daylight Opening minus 3 (76 mm). (1-1/2 [38 mm] each side). To install glass, insert fully into the Top Vinyl, then align the bottom edge with the Bottom Vinyl and press the glass down into the Vinyl. OPTIONAL Add a small bead of CRL 95CBL Black Structural Silicone between the glass corner edges within the bottom vinyl area. Optional CRL 95CBL Black Structural Silicone Optional CRL 95CBL Black Structural Silicone Page 6 of 12 1M
7 100 Series Picket Installation: Install Picket Vinyl into the Top and Bottom Rails. Snap fit one Picket Spacer onto Top and Bottom Rails adjacent to the Post. Cut Pickets to length using: Daylight opening Plus 1-1/2 (38 mm). Install picket, then snap fit next set of spacers, and continue on. Helpful Hints: Install the last few Pickets together before snap fitting the Spacers. Then fit the Spacers evenly between the Pickets. Trim the last set of Spacers to fit the remaining gap. TOP CAP TOP RAIL TOP CAP TOP VINYL TOP RAIL TOP CAP BOTTOM RAIL PICKET SPACER BOTTOM RAIL BOTTOM VINYL Page 7 of 12 1M
8 200, 300, & 400 Series Installation Instructions 200, 300, & 400 Series Top Cap Installation: Illustrations are of the 200 Series. 300, & 400 Series follow the same procedures. Cut Top Cap to length. Locate Top Cap onto Posts and secure with self-drilling Tek Screws Cat. No. TEK1. Install End Caps with Flat Head Screws Cat. No. ECS1. Helpful Hints: Use the die line on the bottom leg of the Top Cap extrusion as a guide for the screws. Screws should be centered over the Post. 200, 300, 350 & 400 Series Rail Connecting Block Installation: Install the Rail Connector Blocks onto the Posts using the self-drilling screws provided. The Rail Connector Blocks (Cat. No. RCB2) are used to support the Bottom Rails. Typically the distance from the floor to the bottom of the rail is 3 (76 mm). This will require the holes for the Rail Connector Blocks to be 4-3/8 (111 mm) up from the floor. Helpful Hints: Use the Die Lines in the Post extrusion as a guide for the holes. This will ensure the Rail Connector Block is centered on the post. Height of the holes is dependent on the height of the Bottom Rail from the floor. CONNECTING BLOCK RCB " STANDARD RCB2 POSITION Page 8 of 12 1M
9 350 Series Top Cap Installation: Secure the 350 Series Post Top Adjustable Brackets Cat. No. CB350L and CB350R to the top of the Posts using the #14 x ¾ (19 mm) Screw Cat. No. CBS1. Two right-sided Brackets or two left-sided Brackets are needed for center 180 degree Posts, and a left-sided Bracket and a right-sided Bracket is needed for Corner 90 Degree Posts. Cut Top Cap to length. Locate Top Cap onto Adjustable Brackets and secure from under Top Rail with self-drilling Tek Screws Cat. No. TEK SERIES TOP RAIL 350 SERIES END CAP END CAP SCREWS #14 X 1-1/2" F/H SCREWS CB350 BRACKET 2-3/8" TEK1 TEK SCREW TEK1 35TRH CB350L BRACKET CB350R MITER IN FIELD CB350L 90 CONNECTION 180 CONNECTION Page 9 of 12 1M
10 200, 300, 350 & 400 Series Top Infill and Bottom Rail Installation: For glass infills use deep Top and Bottom Rails. For Picket Infills use shallow Top and Bottom Rails. Top and Bottom Rail Installation for Glass: Cut rails to length between Posts. Snap fit Top Infill into Top Rail. Press Bottom Rail over Rail Connector Blocks and secure with self-drilling Screws provided. Helpful Hints: Use the die line on the bottom leg of the Bottom Rail extrusion as a guide for the Screws. Screws should be approx. ½ (12 mm) from the edge of the Post. Page 10 of 12 1M
11 200, 300, 350 & 400 Glass Installations: Cut Top and Bottom Vinyl the same length as the Rails. Press fit the Vinyl into the Rails. Glass size is determined by the daylight opening. Height: Daylight Opening plus 3/4 (19 mm). Width: Daylight Opening minus 3 (76 mm). (1-1/2 [38 mm] each side). To install glass, insert fully into the Top Vinyl, then align the bottom edge with the Bottom Vinyl and press the glass down into the Vinyl. OPTIONAL Add a small bead of CRL 95CBL Black Structural Silicone between the glass corner edges within the bottom vinyl area. Optional CRL 95CBL Black Structural Silicone Optional CRL 95CBL Black Structural Silicone Page 11 of 12 1M
12 200, 300, 350 & 400 Picket Assemblies: Cut Top and Bottom Infill extrusion to length. Drill 1/4 (6 mm) diameter holes at 3-7/8 (98 mm) centers in both Top and Bottom Rails Cut Pickets to desired length and secure to Top and Bottom rails with screws provided. Helpful Hints: C.R. Laurence offers several standard pre-assembled Picket Panels, and can make custom sizes as required. This will save considerable time on the job site. 3 7/8" 200, 300, 350 & 400 Picket Installations: Raise Picket assembly up into the Top Rail. Slide panel so that the Bottom Rail fits over Rail Connector Blocks. Press assembly down and move to vertical. Push up and clip fit Top Infill into Top Rail. Secure Bottom Rail to Rail Connector Blocks with self-drilling Screws Cat. No. TEK1 provided. 3 7/8" Page 12 of 12 1M
ALUMINUM RAILING INSTALLATION INSTRUCTIONS. 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list.
ALUMINUM RAILING INSTALLATION INSTRUCTIONS AF#2010-308D Glass Infill Systems 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. 2) Gather and Identify
More informationHorizontal Cable Systems
ALUMINUM RAILING INSTALLATION INSTRUCTIONS v2012 orizontal Cable Systems 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. 1A) Coastal applications:
More informationALUMINUM RAILING INSTALLATION INSTRUCTIONS. 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list.
ALUMINUM RAILING INSTALLATION INSTRUCTIONS AF#2010-308A Glass Infill Systems 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. 2) Gather and Identify
More informationHorizontal Cable Systems
ALUMINUM RAILING INSTALLATION INSTRUCTIONS Horizontal Cable Systems 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. 1A) Coastal applications: Confirm
More information2x Bottom Bracket. 1x Rail Support STEP 1 STEP 2
Level Railing Top Rail Bottom Rail Aluminum Baluster 2x Bottom Bracket 1x Rail Support Kit Includes: 1 - Top Rail (with Baluster Connectors installed) 1 - Bottom Rail (with Baluster Connectors installed)
More informationInstallation Instructions
File #2013-640A Installation Instructions for DesignRail Aluminum Rail Kits with CableRail Cable Infill - LEVEL RAILING 36-42 high railing for residential applications between wood or non-ferrous metal
More informationLevel Railing. Installation Guide. v2.5 W W W. S O L U T I O N S A L U M I N U M. C O M
Level Railing Installation Guide Top Rail Bottom Rail Aluminum Baluster 2x Bottom Bracket 1x Rail Support #909915 Kit Includes: 1 - Top Rail (with Baluster Connectors installed) 1 - Bottom Rail (with Baluster
More informationBSM, GSM & GSS. Joint Kit Instruction. (Modified for IMPACT) (NSF Certified) Curved Glass Fresh Meat Delicatessen and Seafood Merchandisers
BSM, GSM & GSS Joint Kit Instruction (Modified for IMPACT) (NSF Certified) Curved Glass Fresh Meat Delicatessen and Seafood Merchandisers February, 1999 JOINT ASSEMBLY PARTS LIST Item Quantity Description
More informationInstallation Instructions - Model V4JSD 1
Installation Instructions - Model V4JSD 1 Support Assemblies: Parts list: (Note see enclosed cut sheet for quantities and dimensional information) A vertical structural member (1 ½ x 1 ½ modular frame)
More informationATLANTIS RAIL Contact Information
ATLANTIS RAIL Contact Information Customer Service (800) 541-6829 (508) 732-9191 Spectrum System Installation Instructions Atlantis Rail s Spectrum System is an easy to install, universal cable railing
More informationInstallation Instructions
Important 1. Acclimate materials 24 hrs before installation. Maintain temperature controlled environment after installation. 2. Install in accordance with manufacturer s installation instructions. Failure
More informationStorefront Installation Guide
Storefront General Notes: 1. Check Contract Documents and Shop Drawings. Understand and clarify any Field Verify Notes and approvals of drawings and products to be familiar with the project. Installation
More informationOpen Up Your View With CABLE SYSTEMS
Open Up Your View With CABLE SYSTEMS PRESENTED BY CROWN HERITAGE Our Cable Multiple options to accomodate any deck or stair design Marine Grade 316 stainless steel Swaging is the term used for attaching
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SHOWER DOOR KIT ALUMINUM 2503 E. Vernon Avenue, Los Angeles, CA 90058-1826 Phone: (800) 421-6144 EXT. 7740 Fax: (800) 458-7496 crlaurence.com Email: showers@crlaurence.com 11M0260
More informationInstallation Instructions
Important 1. Acclimate materials 24 hrs before installation. Maintain temperature controlled environment after installation. 2. Install in accordance with manufacturer s installation instructions. Failure
More informationInstallation Instructions 1500/1500W/G Wall Guard Important
Important 1. Acclimate materials 24 hrs before installation. Maintain temperature controlled environment after installation. 2. Install in accordance with manufacturer s installation instructions. Failure
More informationReady To Go SimpleSpec tm. Installation Manual. For more information, please visit 3-form.com or call
Contents Overview ( 1) 3/8" Varia Panel = Cable Tensioner with Cover Plate KIT Stainless Steel: 3-15-1636-K Black Oxide: 3-15-2005-K Cable Tensioner with Cover Plate SS: 3-15-1636 BO: 3-15-2005 + M8 Thread
More informationSECTION 19: Endwood Fusion Welded Gate Installation Guide
SECTION 19: Endwood Fusion Welded Gate Installation Guide ASSEMBLY AND INSTALLATION FOR: Fusion Welded Gates Gate Frame with Full Size Pickets Privacy & Board on Board California & Shadowbox Gate width
More informationa.k.a. casegoods instructions
a.k.a. casegoods instructions a a.k.a. workwall installation IMPORTANT NOTES Failure to install product according to installation instruction will result in loss of warranty. Tools required for assembly
More informationThe following instructions will guide you through the installation of your new vinyl railing.
Installation Guide St. James Vinyl T-Rail Tools Required Protective eye glasses 3/8 x 3 Concrete Anchors/Fasteners (for Tape measure concrete installations) Variable speed drill/screwdriver Philips Driver
More informationINSTALLATION INSTRUCTIONS
Tools required for the installation. A. Core Drill 87mm Drill bit B. Tape measure C. Spirit Level D. Marking pen E. Caulking gun F. Cutting Pliers G. Cordless Drill and Philips head bit, 5mm Drill bit.
More informationINSTALLATION INSTRUCTIONS
Tools required for the installation. A. Core Drill 87mm Drill bit B. Tape measure C. Spirit Level D. Marking pen E. Caulking gun F. Cutting Pliers G. Cordless Drill and Philips head bit, 5mm Drill bit.
More informationDeckRail A Product of DeckRite LLC 3912 East Progress North Little Rock, AR Phone: (501) Fax: (501)
Disclaimer: Deck Rail Glass Railing Installation Guide This guide is not intended to replace a trained professional installer. The drawings and instructions contained within are for demonstration purposes
More informationResidential & Industrial Fence
Page Residential & Industrial Fence Assembly Instructions Congratulations on the purchase of your new Fence System. Your fence has been designed to give you years of trouble free service with only minimal
More information86-1/2" TRACK INSTALLATION GUIDE
BARN TRACK 86-1/2" TRACK INSTALLATION GUIDE READ ALL INSTRUCTIONS AND REVIEW DIAGRAMS BEFORE BEGINNING THE INSTALLATION TO GET A THOROUGH UNDERSTANDING OF THE PROCESS. BEFORE YOU BEGIN This kit comes with
More informationINSTALLATION INSTRUCTIONS. Level Rail With Cap: Page 2 Level Rail Without Cap: Page 8 Stair Rail: Page 12
INSTALLATION INSTRUCTIONS Level Rail With Cap: Page 2 Level Rail Without Cap: Page 8 Stair Rail: Page 12 LEVEL RAIL WITH CAP The testing was performed in accordance with procedures and methods referenced
More information2013 Feeney (2/14) # B. Aluminum Railing Systems
2013 Feeney (2/14) #2012-425B Aluminum Railing Systems Aluminum Railing Systems Searching For a Complete Railing System? Look No Further. DesignRail by feeney aluminum railing frame systems combine the
More informationThe following instructions will guide you through the installation of your new vinyl railing stair kit.
Installation Guide Vinyl Standard Stair Railing Tools Required Protective eye glasses Tape measure Variable speed drill/screwdriver Rotary hammer or hammer drill and masonry percussion bit recommended
More informationCountry Estate Railing Installation Guide
Country Estate Railing Installation Guide Country Estate Railings are fabricated with the highest quality Railing products available and will provide you with many years of comfort and security. Please
More informationBioPrism Solid Surface
Please read all instructions before installing products. These instructions are intended for use with InPro s standard toilet partitions, which include 58 high doors and wall panels, when deviating from
More informationINSTALLATION INSTRUCTIONS. Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING
JANUARY, 2014 1 INSTALLATION Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING INSTRUCTIONS 2 FRAME ASSEMBLY JANUARY, 2014 601442 SHEAR BLOCK BALL BEARING NRP BUTT (FACTORY APPLIED
More informationOxford Stalls Installation Instructions
Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or
More informationPrivacy Wall Glass Selections - Polished Edge Slider Door
Privacy Wall Glass Selections - Polished Edge Slider Door 3/6" HEX BIT PUTTY KNIFE #2 ACR BIT SUCTION CUP HOLDERS DOOR LEAF: Satin Tempered Clear Tempered LOCTITE 425 SIDE LIGHT ETCHED GLASS STYLES: Satin
More informationTREX TRANSCEND RAILING
RAILING NOTES:» RAILINGS ARE DESIGNED TO BE INSTALLED OVER THE DECKING FRAME OR ON INSIDE OF RIM JOIST. NOTCHING OF PRESSURE-TREATED POSTS OR POSTS INSTALLED ON OUTSIDE OF RIM JOIST IS NOT ALLOWED.» All
More informationFrameless Inline Door QCI5248
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5248 FRAMELESS PANEL / DOOR / PANEL QCI5248 REV. 0 Page 1 Certified 06/16/2016 Parts List with glass to glass hinges *Quantities may vary. **Support Bar
More informationFIXED PANEL SLIDER QCI5241
INSTALLATION INSTRUCTIONS FIXED PANEL SLIDER QCI5241 FRAMELESS PANEL / DOOR / PANEL FRAMELESS DOOR / PANEL QCI5241 REV. 0 Page 1 Certified 06/16/2016 Parts List *Quantities may vary QCI5241 REV. 0 Page
More informationCURVED ROOF ASSEMBLY INSTRUCTIONS ATTACHED VERANDAH. Your supplementary guide to building an ATTACHED CURVED ROOF VERANDAH or PATIO BEFORE YOU START
ROOF ATTACHED VERANDAH ASSEMBLY INSTRUCTIONS Your supplementary guide to building an ATTACHED ROOF VERANDAH or PATIO This set of instructions should be used in conjunction with the Stratco instruction
More informationC.R. LAURENCE CO., INC.
C.R. LAURENCE CO., INC. GRS GLASS RAILING DRY GLAZE TAPER-LOC SYSTEM * *Patent Pending FOR TEMPERED GLASS APPLICATIONS Installation Instructions See the video at crlaurence.com TAPER-LOC Sets consist of
More informationRevision Date: April 01, Paramount Enclosure
Paramount Enclosure www.urbanindustries.com 15 Urban Industries, Inc. 2008 Tools The following tools are recommended for the installation of the Paramount Aluminum Enclosure and roof. 1 2 Level 1 4 Level
More informationINSTALLATION INSTRUCTIONS VENETIAN 84" SLIDING SHOWER DOOR SYSTEM (180º INSTALLATION)
INSTALLATION INSTRUCTIONS VENETIAN 84" SLIDING SHOWER DO SYSTEM (180º INSTALLATION) 28539 Industry Drive, Valencia, CA 91355 Toll Free Phone: (877) 728-3874 Toll Free Fax: (888) 440-9567 Phone: (661) 775-1675
More informationDeckRail A Product of DeckRite LLC 3912 East Progress North Little Rock, AR Phone: (501) Fax: (501)
Deck Rite Welded Picket Railing Installation Guide Disclaimer: This guide is not intended to replace a trained professional installer. The drawings and instructions contained within are for demonstration
More informationSmall Flush Wood Flue Adapter Installation Instructions (SKU )
Warning Regarding Draft Use of any offset adapter may degrade draft performance of the insert. To minimize the adverse effects, set the adapter to the minimum offset possible. Any leaks in the adapter
More information2015 Feeney (8/15) # D. Aluminum Railing Systems
2015 Feeney (8/15) #2012-425D Aluminum Railing Systems Aluminum Railing Systems Searching For a Complete Railing System? Look No Further. DesignRail by feeney aluminum railing frame systems combine the
More informationALL SEASON PATIO COVER
ALL SEASON PATIO COVER 61 Where the All Season Patio Cover is to be attached to the home, create a level line showing where the top of the mounting rail is to be located. Install each section with the
More information9/16" (14mm) 1/2" (12mm)
Deluxe Header Kit Deluxe Header Kit Cat. No. SDH660-66" (1676mm) Length Cat. No. SDH980-98" (2489mm) Length Cat. No. SDH144-144" (3657mm) Length Each Deluxe Header Kit Contains: 66" (1676mm), 98" (2489mm)
More informationInstallation Instructions
Important SECTION VIEW 1. Acclimate materials 24 hrs before installation. Maintain temperature controlled environment after installation 2. Install in accordance with manufacturer s installation instructions.
More informationFor installation assistance, contact SARGENT at DOORS SHOWN HERE SWING IN FOR ILLUSTRATION PURPOSES ONLY.
SARGENT Installation Instructions for LP8600 x LR8600 & 12-LP8600 x 12-LR8600 Series Low Profile Panic and Fire Exit Devices on Double Egress & Double Doors or LS8600 & 12-LS8600 Low Profile Exit Device
More informationPORCH-LOC INSTALLATION INSTRUCTIONS
PORCH-LOC INSTALLATION INSTRUCTIONS 2017 HB&G Building Products, Inc. Porch-Loc Installation Instructions NOTE: DISCARD THE INSTALLATION INSTRUCTIONS AND HARDWARE THAT CAME IN YOUR PERMAPOST PACKAGING
More informationTOOLS REQUIRED Metal Wood Wood and Metal Screws. #16 Drill #12-24 Tap. 1/8 Drill
DEVICES COVERED IN THIS DOCUMENT: 4700S Surface Vertical Rod Device 4700SF Fire Exit Surface Vertical Rod Device TOOLS REQUIRED Metal Wood Wood and Metal Screws Sex Bolts #7 Drill ¼ -20 Tap #16 Drill #12-24
More informationAFCO-Rail Post INSTALLATION INSTRUCTIONS AFCO-RAIL POST
AFCO-Rail Post INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Drill Bits (for the appropriate fastener) Drill (with adjustable clutch, recommended) Level String Line Tape Measure Tools to install fasteners
More informationSemi-Frameless Hinged Door With Panel And Return
202 Anderson Ave., Belvue, KS 66407 Phone: 800-669-9867 Fax: 800-393-6699 www.onyxcollection.com 800-643-1514 www.alumaxbath.com Semi-Frameless Hinged Door With Panel And Return Full Showers with Return
More information40mm Thermoclick. Type II Class 1 Clear Satin Anodize - 201R1 (Mid Grade Commercial)
http://www.sundancesupply.com 40mm Thermoclick Type II Class 1 Clear Satin Anodize - 201R1 (Mid Grade Commercial) U-Profile 12' Lengths $39 Out System offers a complete set of extrusions and accessories
More informationInstallation Instructions for. Before You Begin TOOLS REQUIRED
Composite Railing System STEP-BY-STEP Installation Instructions for Spectrum Composite Railing Virtually maintenance free 20-year warranty EverNew Spectrum Railing system is designed to work with a number
More informationSIG Awning / Casement / Fixed Lite 100
TYPICAL FRAME ASSEMBLY - AWNING WINDOW 07-01 85720-2 GASKET EXT FL JAMB 100 BS201 (3471) HEAD HINGED 100 86064 TRIM FIN A 83963 SCREW SQ 8G X 1.0 PAN PP SS #2 85737 GASKET EXT FL TRANSOM 85720-1 86065
More informationTHANK YOU FOR PURCHASING FROM HERITAGE PATIOS
Installation Guide THANK YOU FOR PURCHASING FROM HERITAGE PATIOS Your purchase is engineered by nearly a half century of commercial and residential product design proudly manufactured in the USA from responsibly
More informationDura-Lock Roof System
DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.
More informationx2 1/4 (6mm) Floor Anchor
INSTALLATION GUIDE Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Straight Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm
More informationSection 8. Curved units. Curved units
Section 8 Curved units Curved units Curved corner post... page 94 Curved base cabinet... page 95 Curved wall cabinet... page 96 Curved deep wall cabinet... page 97 Curved plinth - Joining... page 99 www.howdens.com
More informationTemplate. Blue 242. May 2018 trademarks of Suncor Stainless, Inc. Loctite is a registered trademark of Henkel Corporation
ATLANTIS RAIL Contact Information: Atlantis Rail Systems 70 Armstrong Road 3900 Civic Center Drive Plymouth, MA 02360 North Las Vegas, NV 89030 (800) 541-6829 or (508) 732-9191 (508) 732-9798 www.atlantisrail.com
More informationShetland Stalls Installation Instructions
Shetland Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 1/9/18 Before you start Kit can accommodate up to 12 wide stall front
More informationELEVEN COLLABORATIVE. CONFERENCE TOPS Assembly Instructions
ELEVEN COLLABORATIVE Table of Contents SUPPORT BRACE ASSEMBLY.... 3 TABLE BASE FRAME ASSEMBLY.... 4 LEG ATTACHMENT.... 5 TOP JOINING PLATE ASSEMBLY... 6 TOP CLAMP/TOP SPACER INSTALLATION.... 7 TOP PLACEMENT
More informationPortofino Installation Guide
vjul16 (for 17 or 24 mm Surface Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Portofino shower enclosure. Please study these instructions
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TOOLS REQUIRED Rechargeable, variable speed drill 3/8 diameter drill bit 3 Robertson bits #0, #1 and #2 Slot screwdriver Non marring hammer with 1 head Level Caulk or sealant
More information392CV SERIES Stickstall
202 Anderson Ave., Belvue, KS 66407 Phone: 800-669-9867 Fax: 800-393-6699 www.onyxcollection.com 800-643-1514 www.alumaxshowerdoor.com 392CV SERIES Stickstall TM Corner Shower Enclosure 392CV-1117 Yes!
More information340 & 350 SERIES BATH ENCLOSURES
INSTALLATION INSTRUCTIONS 340 & 350 SERIES BATH ENCLOSURES 800-643-1514 www.alumaxbath.com Copyright Alumax Bath Enclosures 2010. All rights reserved. LIMITED WARRANTY AND REMEDY ALUMAX BATH ENCLOSURES
More informationHarmony 1/4 Glass Railing Installation Instructions - Deck Application
Harmony 1/4 Glass Railing Installation Instructions - Deck Application Items Required for Installation Appropriate fasteners for mounting posts to deck Miter saw with carbide-tipped non-ferrous blade Cordless
More informationFrameless Inline Door With Return QCI5263
INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges
More informationTREX ENHANCE RAILING (Also Applies to Trex Select Railing) Installation Instructions
TREX ENHANCE RAILING (Also Applies to Trex Select Railing) NOTE: All Enhance Railing lengths are manufactured at CLEAR SPAN dimensions (spanning between space of posts): 7" for 6' clear span. Note that
More informationRAILING R A IL ING 51
RAILING RAILING 5 TREX TRANSCEND RAILING NOTES:» TREX TRANSCEND RAILINGS ARE DESIGNED TO BE INSTALLED OVER THE DECKING FRAME OR ON INSIDE OF RIM JOIST. NOTCHING OF PRESSURE-TREATED POSTS OR POSTS INSTALLED
More informationHover. Installation Instructions. Raised Panel. Version
Installation Instructions Version 8-2-17 Raised Panel Table of Contents Page Raised Panel Trough 3-13 Platform Trough 14-20 Platform 120 Degree Trough 21-24 Electrical 25-28 Type A Electric Bases 29-31
More informationVinyl Sliding Glass Door Assembly Instructions
Vinyl Sliding Glass Door Assembly Instructions SERIES SGD 5470/5570 Para instrucciones en español, visite: http://bit.ly/pgtassemblyinstructions Parts List ITEM 4 5 6 7 8 9 0 4 5 6 7 8 SGD 5470/5570 PARTS
More informationMonaco Installation Guide - Surface Profiles
v1 Page 1 Thank you for purchasing this Monaco shower screen. Please study these instructions carefully before assembly and installation and check all supplied parts immediately upon receipt. These instructions
More informationDeauville Installation Guide
vjul16 (for Recessed Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Deauville shower enclosure. Please study these instructions carefully before
More informationCurium 19.4H Installation Instructions & Parts List
Curium 19.4H Installation Instructions & Parts List Illustration Curium 19.4H Right Hand Page 1 of 21 30/06/2016 Revision 1.0 IMPORTANT This shower screen / enclosure must be installed by suitably qualified
More informationINOVO 2-LITE SLIDING PATIO DOOR
INOVO 2-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More informationFIXED SHOWER SCREEN For Wall Mount Hinges QCI5283
FIXED SHOWER SCREEN For Wall Mount Hinges QCI5283 QCI5283 Page 1 Date Certified: 06/16/2016 Parts List with wall mount clamp ITEM NO. DESCRIPTION QTY. 1 FIXED GLASS PANEL 1 2 WALL MOUNT CLAMP 1 3 U-CHANNEL
More informationINSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE:
INSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE: 268 June 22, 2010 TOOLS NEEDED COMPONENTS INCLUDED P2 Tip 3/8" Drill Rubber Gasket(s) x 2 Bracket(s) x 2 1/2" Drill Bit Bulkhead Flange #2 Phillips
More informationRAILING. Installation Guide
RAILING Installation Guide THE BEST CHOICE FOR STRONG & DURABLE RAILING SYSTEMS Our exclusive manufacturing process ensures our vinyl railing will provide superior strength plus it is virtually maintenance
More informationAluminum Railing Installation. Glass Railing Spindle Railings Intimacy Railings and Panels
Aluminum Railing Installation Glass Railing Spindle Railings Intimacy Railings and Panels This information in this manual will help you to Better understand our product line. Give you guidelines for an
More informationTape Measure Carpenter s Square Touch-up Paint Chalk Line. Blue 242. Template
ATLANTIS RAIL Contact Information: Atlantis Rail Systems 70 Armstrong Rd. Plymouth, MA 02360 (800) 541-6829 or (508) 732-9191 (508) 732-9798 www.atlantisrail.com NOVA System Installation Instructions The
More informationIMPORTANT INSTALLATION GUIDE VALENCIA ANGLE CORNER SHOWER READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING THE INSTALLATION
INSTALLATION GUIDE VALENCIA ANGLE CORNER SHOWER SEALANT REQUIRED TO COMPLETE THIS INSTALLATION: (Supplied) Sika Sikasil NG (Arctic White) To seal the WHITE shower door and returns to the shower tray. Usage:
More informationInstallation Operation Care
Installation Operation Care Palm Beach Polysatin Shutters CONTENTS Getting Started Installation Overview...1 Unpacking...1 Tools and Materials Needed...1 Fasteners...2 Frame Assembly Assemble the Frame
More informationINSTALLATION INSTRUCTIONS SIDELITE ASSEMBLY SERIES 900 TERRACE DOOR AND SERIES 925 PATIO DOOR
INSTALLATION INSTRUCTIONS SIDELITE ASSEMBLY SERIES 900 TERRACE DOOR AND SERIES 925 PATIO DOOR Phone: (800) 262-5151 Fax: (866) 262-3299 crlaurence.com usalum.com crl-arch.com 11M0292 HANDLING, STORAGE,
More informationSIMPLER BETTER FASTER
SIMPLER BETTER FASTER 1. FITTING RING BEAMS DETAILS Always work anti-clockwise viewed from outside the roof. Each bar should be sequentially numbered, i.e. 1, 2, 3. Select the ring beam, position the left
More informationInsolroll Clutch Operated Shades Installation Instructions Installation Instructions
All clutch operated shades are shipped fully assembled and ready for installation. Mounting screws are not provided. Screws for chain guide installation to meet the child safety standards are provided.
More informationFrameless Inline Door QCI5250
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5250 FRAMELESS PANEL / DOOR / PANEL QCI0249 REV. 3 Page 1 Certified 10/12/12 Parts List with pivot hinges *Quantities may vary. QCI0249 REV. 3 Page 2
More informationKai Installation Instructions
Kai Installation Instructions Before Beginning Installation Read through the entire instruction thoroughly A minimum of 2 people are required for this assembly These instructions reflect typical assemblies;
More informationINSTALLATION INSTRUCTIONS GUIDE
CERTAINTEED RAILING AND DECKING INSTALLATION INSTRUCTIONS GUIDE Kingston Vinyl Railing and Vinyl Decking CONTENTS Important Information Before You Begin...3 Helpful Hints, Tips, Fire Information and Tools
More informationBaby Grande with Crank, Housing, and Side Rails Installation Instructions
Baby Grande with Crank, Housing, and Side Rails Installation Instructions Tools Needed Hardware Provided (per shade) Hardware Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil
More informationDeauville Installation Guide
vjul16 (for 17 or 24 mm Surface Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Deauville shower enclosure. Please study these instructions
More informationVersatrac R-System Stock Extrusions, Clips and Accessories
Versatrac R-System Extrusions are available in 300 series (for 3 3/4" walls) and 400 series (for 4 7/8" walls). Standard finishes are Satin Metallic Bronze, Satin Black, Satin White Baked Enamel, and Clear
More informationInstallation Instructions
Installation Instructions 200 Series Curtainwall 3056 WALKER RIDGE DR. NW, SUITE G WALKER, MI 49544 800-866-2227 dependable@tubeliteinc.com Revised April 2014 dependable@tubeliteinc.com Page 1 TABLE OF
More informationSafety Glasses Safety Gloves Ladders Measuring Tape Spirit Level String Line. Tin-Snips Rivet Gun Caulking Gun Silicone Socket Set
BEFORE YOU START Carefully read these instructions and refer to them constantly during each stage of construction. If you do not have all the necessary tools or information, contact Stratco for advice.
More informationx2 1/4 (6mm) Floor Anchor
Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Bent Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm x 90mm) Wall Screw x2
More informationInstallation manual. For setting in concrete/on base plates - Panel height 1830
1 Aluminium fencing and drive-in gates Installation manual For setting in concrete/on base plates - Panel height 1830 Aluclos system components: U10 Connecting U-bracket 1900 mm CL18/CL18.XL Half-height
More informationYES 600 Thermal Clip Storefront System Installation Manual
Installation Manual 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii Frame Types............................................
More informationATLANTIS RAIL Contact Information: Atlantis Rail Systems 70 Armstrong Road 3900 Civic Center Drive Plymouth, MA North Las Vegas, NV 89030
ATLANTIS RAIL Contact Information: Atlantis Rail Systems 70 Armstrong Road 3900 Civic Center Drive Plymouth, MA 02360 North Las Vegas, NV 89030 (800) 541-6829 or (508) 732-9191 (508) 732-9798 www.atlantisrail.com
More informationINSTALLATION INSTRUCTIONS FOR PLASCORE F5075 FRAME WALL
INSTALLATION INSTRUCTIONS FOR PLASCORE F5075 FRAME WALL The following information is provided by Plascore, Inc., as a general guideline for the installation of the F5075 Frame Wall System. This information
More informationINOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS
INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More informationTREX SELECT RAILING Installation Instructions
RAILING NOTE : All Trex Select Railing lengths are manufactured at ON CENTER dimensions (spanning from center of each post): 67-5/8" (76.8 cm) for 6' (.83 m) on center, and 9-5/8" (35.3 cm) for 8' (.44
More information