SINGLE PIECE MASONRY HANGERS
|
|
- Cornelius Burns
- 5 years ago
- Views:
Transcription
1 SINGE PIECE MASONRY ANGERS TECNICA DATA SEET The FM Single Piece Joist anger is designed to support timber joists built in to brick or block walls with a minimum crushing strength of 3.5N/mm². They are also suitable for many timber to timber applications by fixing the masonry flange securely to the timber or to steel beams using appropriate fixings. Galvanised steel to EN DX51D Z600. Tested by CERAM Research td Notification ody No Manufactured to EN 845-1:2013. Straight top flange. Can easily be transformed into a hook over joist hanger using the unique FM ock Plates, no special tools or rivets are required. Just insert ock Plate at 90, rotate and tap into place. No welds. FM angers 150mm and above are manufactured 10mm less to allow for notching out regularised timber. - - idth eight Single Piece Masonry angers idth eight Performance Data anger eight Joist eight idth Characteristic value (kn) Eurocode Safe working load (kn) S TDS-M-V1 DATE ISSUED M M M M M M The back plate of the hanger should lie flat against the vertical masonry support. Masonry flange should have a minimum of 3 courses (675mm masonry) above. oth supporting and above masonry should be allowed to mature before any load is applied. Joist should be square cut and sit tight to the back of the hanger - maximum gap permitted is 6mm. *All values are derived in line with EN 845-1:2013 based on a declared value of 10.8kN. Nail the side flanges with 30 x 3.75mm galvanised square twist nails or equivalent. Stainless steel hangers should be nailed using 30 x 3.75 annular ring shank nails. To provide lateral restraint D straps should be used. The masonry flange should always be securely fixed or adequately embedded and should never be placed in dry slots. Use appropriate fixings. Always ensure that compatible corrosion resistant fixings are used, i.e. do not use galvanised fixings with stainless steel products or vice versa. Use correct strength mortar as per ritish Standard.
2 EDED MASONRY ANGERS TECNICA DATA SEET The M elded Masonry Joist anger is designed to support timber joists built in to brick or block walls with a minimum crushing strength of 3.5N/mm². They are also suitable for many timber to timber applications by fixing the masonry flange securely to the timber or to steel beams using appropriate fixings. Galvanised steel to EN10346 DX51D Z275 or grade austenitic stainless steel to EN Tested by CERAM Research td Notification ody No Manufactured to EN 845-1:2013. Flexibility of design means as well as the standard sizes shown the M can be manufactured in any size to order. 2.4mm thick. - - idth eight elded Masonry angers elded Masonry angers - Stainless Steel idth eight idth eight 75150M M M M M M M M M M M M M M MS MS MS MS MS MS MS MS MS Stainless Steel items can be purchased in singles. TDS-M-V1 DATE ISSUED Performance Data anger eight idth Characteristic value (kn) Eurocode Safe working load (kn) S The back plate of the hanger should lie flat against the vertical masonry support. Masonry flange should have a minimum of 3 courses (675mm masonry) above. oth supporting and above masonry should be allowed to mature before any load is applied. Joist should be square cut and sit tight to the back of the hanger - maximum gap permitted is 6mm. Nail the side flanges with 30 x 3.75mm galvanised square twist nails or equivalent. Stainless steel hangers should be nailed using 30 x 3.75 annular ring shank nails. To provide lateral restraint D straps should be used. The masonry flange should always be securely fixed or adequately embedded and should never be placed in dry slots. Use appropriate fixings. Always ensure that compatible corrosion resistant fixings are used, i.e. do not use galvanised fixings with stainless steel products or vice versa. Use correct strength mortar as per ritish Standard.
3 MUTI-FUNCTIONA ANGERS TECNICA DATA SEET The Face Fix Range of Joist angers are designed for applications where additional strength is required or where access to the top of the timber or steel is not available. This range can be nailed or bolted. All values are given based on all nail holes being used, for bolting values please refer to the bolt manufacturers guidelines. The hanger should be a minimum of over half (60%) the depth of the supported member to avoid rotation. Galvanised steel to EN DX51D Z275. Tested by CERAM Research td Notification ody No (applies to the MF only) MFM - 1.2mm thick & MFT - 2mm thick. ocation tabs aid fast accurate alignment of the hanger. M12 bolt holes. 85mm bearing. - - idth eight Muti Functional angers idth eight Number of nails (30 x 3.75) eader Joist idth eight Number of nails (30 x 3.75) eader Joist 47240MMF MF MF MF MF MF MF MF MF MF MF MF Performance Data TDS-MF-V1 DATE ISSUED MMF 47346MF 47404MF 47504MF 76346MF 76404MF 76504MF 90504MF MF MF MF MF Characteristic value (kn) Eurocode Safe working load (kn) S Short Term Safe working load (kn) S Medium Safe working load (kn) S ong Term All holes should be nailed using 30 x 3.75 square twist nails or equivalent, for stainless steel products use 30 x 3.75 stainless steel annular ring shank nails. Always ensure that compatible corrosion resistant fixings are used, i.e. do not use galvanised fixings with stainless steel products or vice versa.
4 TIMER TO TIMER ANGERS TECNICA DATA SEET Timber to timber joist hangers to support floor joists and trimmers of varying depths. oody No Tag Galvanised steel to EN DX51D Z275. oody Standard Galvanised steel EN DX51D Z275 or Grade austenitic stainless steel to EN Tested by Ceram Research td Notification ody No oody No Tag Designed to allow easy fixing of plasterboard. Superior design allows for the use of fewer nails for faster installation. oody Standard Increased leg lengths, all widths can take up to 225mm deep joist. Available up to 150mm wide. Tag on the base of the hanger to help avoid rotation and aid fast, accurate location. The tag can be bent if not required idth ength earing Timber angers - No Tag Timber angers - Standard idth eg Joist earing Joist Size x D to D idth eg Joist earing Joist Size x D to D 44T x 125 to T x 125 to T x 125 to T x 125 to T x 125 to T x 125 to T x 100 to T x 100 to Timber angers - Stainless Steel TDS-T-V1 DATE ISSUED All holes should be nailed using 30 x 3.75 square twist nails or equivalent, for stainless steel products use 30 x 3.75 stainless steel annular ring shank nails. Performance Data idth eg Joist earing Joist Size x D to D 47TS x 100 to TS x 100 to TS x100 to T 47T 63T 75T 90T 100T 125T 150T 47TS 76TS 100TS Characteristic value (kn) Eurocode Safe working load (kn) S Short Term Safe working load (kn) S Medium Term Safe working load (kn) S ong Term Number of Nail holes Always ensure that compatible corrosion resistant fixings are used, i.e. do not use galvanised fixings with stainless steel products or vice versa.
5 ONG EG - TIMER TO TIMER ANGERS TDS-T-V1 DATE ISSUED TECNICA DATA SEET Timber angers - No Tag idth eg Joist earing Timber to timber joist hangers; designed for use in loft conversions where the hanger extends below the support. Galvanised steel EN DX51D Z275 or Grade austenitic stainless steel to EN Tested by CERAM Research td Notification ody No The superior design does not require wide straps making them easier to install on site. oads below are from tests where the ong eg is hung 100mm below the support with all available holes nailed. Far greater load carrying capabilities than other leading brands. 450mm and 600mm legs available. Joist Size x D to D 44450T x 150 to T x 150 to T x 175 to T x 150 to T x 150 to T x 175 to T x 175 to Performance Data All available holes should be nailed using 30 x 3.75 square twist galvanised nails or equivalent, for stainless steel use 30 x 3.75 annular ring shank nails. Always ensure that compatible corrosion resistant fixings are used, i.e. do not use galvanised fixings with stainless steel products or vice versa T 47450T 76450T 90450T T T T Characteristic value (kn) Eurocode Safe working load (kn) S Short Term Safe working load (kn) S Medium Term Safe working load (kn) S ong Term idth ength earing
6 MINI - TIMER TO TIMER ANGERS TDS-TM-V1 DATE ISSUED TECNICA DATA SEET Mini Timber angers - Galvanised Steel idth eg Joist earing Timber to timber joist hangers suitable for light duty applications such as trimmers, ceiling joists and decking. Galvanised Steel EN DX51D Z275 or Grade Austenitic Stainless Steel to EN Test by CERAM Research td Notification ody No Tag on the base of the hanger helps avoid rotation and aids fast, accurate location. The tag can easily be bent if not required. Joist bearing 50mm. 1.0mm gauge. Two depths available. Joist Size x D to D 44TM x 75 to TM x 75 to All holes should be nailed using 30 x 3.75 square twist nails or equivalent. For stainless steel products use 30 x 3.75 stainless steel annular ring shank nails. Mini Timber angers - Stainless Steel idth eg Joist earing Joist Size x D to D 44TMS x 100 to TMS x 100 to Performance Data idth ength earing 44TM 47TM 44TMS 47TMS Characteristic value (kn) Eurocode Safe working load (kn) S Short Term Safe working load (kn) S Medium Term Safe working load (kn) S ong Term Number of Nail holes
7 EAVY DUTY RESTRAINT STRAPS TDS-S-V1 DATE ISSUED TECNICA DATA SEET Traditional eavy Duty Restraint Straps designed to The uilding Regulations S 5268 Part 3 and other building standards for vlateral restraint. eavy Duty Restraint Straps are generally for horizontal applications providing lateral restraint of roof trusses, rafters and joists tied to masonry. Galvanised steel EN DX51D Z275 or grade austenitic stainless steel. Manufactured to EN 845-1:2013. Tested by CERAM Research td Notification ody No ent eavy Duty Restraint Straps - Galvanised Steel ent eavy Duty Restraint Straps - Stainless Steel Overall ength ength of end 600RS RS RS RS RS RS Flat eavy Duty Restraint Straps - Galvanised Steel Overall ength ength of end 1000FRS Twisted eavy Duty Restraint Straps - Galvanised Steel Overall ength ength of Twist T 600TRS TRS For galvanised straps use min 7 no x 30 square twist nails or equivalent fixed to timber joists / rafters. Popular stock sizes are listed on the following page but straps can be ordered to any length up to 15m. oled 6mm at 25mm offset centres. Available in galvanised or stainless steel. Overall ength - - T - end ength ength end ength Twist ength 1000RSS RSS For stainless steel use min 7 no x 30 annular ring shank stainless steel nails or equivalent fixed to timber joists/rafters. T
8 IGT DUTY RESTRAINT STRAPS TDS-S-V1 DATE ISSUED TECNICA DATA SEET Traditional ight Duty Restraint Straps designed to The uilding Regulations S 5268 Part 3 and other building standards for vertical restraint. ight Duty Restraint Straps are generally for vertical applications such as holding down a wall plate. Galvanised steel EN DX51D Z275 or grade austenitic stainless steel. Manufactured to EN 845-1:2013. Tested by CERAM Research td Notification ody No Popular stock sizes are listed on the following page but straps can be ordered to any length up to 15m. oled 6mm at 25mm offset centres. Available in galvanised or stainless steel. ent ight Duty Restraint Straps - Galvanised Steel ent ight Duty Restraint Straps - Stainless Steel Overall ength ength of end 300RS RS RS RS RS Flat ight Duty Restraint Straps - Galvanised Steel Overall ength ength of end 1000FRS Twisted ight Duty Restraint Straps - Galvanised Steel Overall ength ength of Twist T 1000TRS hen used as a vertical restraint to hold down a wall plate use a minimum length of 900mm. For galvanised straps use min 10 no x 30 square twist nails or 6 no. 4 x 40 screws (drilled and plugged) into the masonry. Use min 2 no x 30 square twist nails into wall plate. Overall ength end ength 1000RSS Flat ight Duty Restraint Straps - Stainless Steel Overall ength - T - end ength ength end ength Twist ength 1000FRSS For stainless steel straps use min 10 no x 30 annular ring shank nails stainless steel or 6 no. 4 x 40 stainless steel screws (drilled and plugged) into the masonry. Use min. 2 no. 30 x 3.75 annular ring shank nails into wall plate. T
9 ANGE RACKETS TDS-A-V2 DATE ISSUED TECNICA DATA SEET Angle rackets - Galvanised Steel idth Use appropriate fixings. eg x Thickness Always ensure that compatible corrosion resistant fixings are used, i.e. do not use galvanised fixings with stainless steel products or vice versa. General purpose brackets for all applications where one member crosses another or one member is trimmed into another. A range of sizes and finishes are available to suit all applications. Galvanised steel EN DX51D Z275. Grade austenitic stainless steel to EN eavy duty brackets with strengthening ribs on bend to give added rigidity. Supporting Ribs 5050A x Not required A x Not required A x Yes A x Yes A x Yes 50 Number of Fixing oles per racket eight ength idth Angle rackets - Stainless Steel idth eg x Thickness Supporting Ribs 6040AS x Not required AS x Yes A 6040A 9090A 15090A A 6040AS 9090AS Number of Nail 3.75mm holes Number of holes M8mm Number of holes M10mm Number of holes M10mm slots Number of holes M6mm
10 UNIVERSA FRAMING ANCORS TECNICA DATA SEET For stronger nailed joints and economical secondary connections in timber framing. Framing Anchors are an effective, versatile and economical method of providing strong, mechanical joints. Suitable for timber of minimum 44 x 44 section. Galvanised steel EN DX51D Z275 or grade austenitic stainless steel to EN mm Pre-galvanised steel. ole to permit the fixing of covering. Universal Anchor that can be bent to suit all applications. - - eight idth Universal Framing Anchor idth x eight Number of nails (30 x 3.75) UFA 40 x All holes should be nailed using 30 x 3.75 square twist nails or equivalent. Always ensure that compatible corrosion resistant fixings are used, i.e. do not use galvanised fixings with stainless steel products or vice versa. TDS-UFA-V1 DATE ISSUED
11 TRUSS CIPS TECNICA DATA SEET Used to fix trusses, girders and rafters to the wall plate. Galvanised steel EN DX51D Z275. Tested by CERAM Research td Notification ody No Installation prongs to aid location. - - idth eight Pre - Galvanised Steel idth eight Number of nails (30 x 3.75) 47TC Performance Data 47TC Characteristic value (kn) Eurocode Safe working load (kn) S Short Term 4.17 All holes should be nailed using 30 x 3.75 square twist nails or equivalent, for stainless steel products use 30 x 3.75 stainless steel annular ring shank nails. TDS-TC-V1 DATE ISSUED
12 NAI PATES TECNICA DATA SEET A versatile plate used to connect or repair timber. Galvanised steel EN DX51D Z275 or grade austenitic stainless steel to EN Strengthening ribs for added rigidity. All holes are pressed countersunk to aid location of the nail and to give a flush finish. - - eight idth Pre-Galvanised Steel - 1mm Stainless Steel - 1mm idth Thickness eight idth Thickness eight 42NP NP NP NP NP NPS Use appropriate fixings. Always ensure that compatible corrosion resistant fixings are used, i.e. do not use galvanised fixings with stainless steel products or vice versa. TDS-NP-V1 DATE ISSUED
13 FRAME CRAMPS TECNICA DATA SEET Traditionally used for fixing wooden door and window frames into block work. Frame Cramps can also be used for restraining masonry to new and existing structures in non-structural applications and can easily be shot fired into steel work. ot dipped spun galvanised to EN ISO 1461:2009. U 50mm upstand for easy fixing. Two 6mm holes and one 8mm hole. Galvanised after manufacture for superior corrosion resistance. - - U - idth ength Upstand eavy Duty Fishtailed Frame Cramps idth Gauge Projection ength Upstand U 100FFC FFC FFC Use appropriate fixings. Always ensure that compatible corrosion resistant fixings are used i.e. do not use galvanised fixings with stainless steel products or vice versa. TDS-FFC-V1 DATE ISSUED
14 FIXING ANDS TECNICA DATA SEET A versatile multi purpose banding that can be cut, bent and formed for all types of light applications. Galvanised steel EN to DX51D Z275 or grade austenitic stainless steel to EN oles: 3.75, M10 round, M10 & M8 square. The square holes are suitable for cup square hex (coach bolts). Ideal for DIY, Industrial and Agricultural uses. Available in stainless steel and galvanised. Multiple hole sizes to add to its versatility. - - idth ength Pre-Galvanised Steel - 0.9mm idth Overall ength (m) 2010F Stainless Steel - 0.7mm idth Overall ength (m) 2010FS Use appropriate fixings. Always ensure that compatible corrosion resistant fixings are used, i.e. do not use galvanised fixings with stainless steel products. TDS-F-V1 DATE ISSUED
15 INDO OARD TIE TECNICA DATA SEET A racket designed as a simple solution for fixing down thewindow board. Galvanised Steel EN DX51D Z mm Pre Galvanised Steel U - - U - idth ength Upstand idth indow oard Tie ength Upstand U Number of holes per Tie 4mm 6mm T Use appropriate fixings. Always ensure compatible corrosion resistant fixings are used, i.e. do not use galvanised fixings with stainless steel products or vice versa. Please see diagram below. TDS-T-V1 DATE ISSUED
Product Dimensions (mm) Overall length (including any bend) Pre Galvanised - 1.4mm thick x 36mm wide. Declared values for the TRS strap
TECO Straps TRS The Ron Sammons The Ron Sammons is lightweight to handle yet retains its structural strength so it can be used instead of a traditional Heavy Duty Strap for providing lateral restraint
More informationF I X I N G B R O C H U R E
F I X I N G B R O C H U R E Joist Hangers Joist Hangers on Steel Beams Fixing Masonry Hangers Speedy Joist Hangers Lateral Restraint Straps Roof Tie Down Straps Herring Bone Joist Strut Bat 'U' Nail Plate
More informationCatnic Pontypandy Industrial Estate Caerphilly CF83 3GL T: F: English version
www.catnic.com Care has been taken to ensure that the contents of this publication are accurate, but Tata Steel Europe Limited and its subsidiaries, which includes Tata Steel UK Limited, do not accept
More informationBuilders Metalwork Product Selector
www.catnic.com Builders Metalwork Product Selector September 2015 Care has been taken to ensure that the contents of this publication are accurate, but Tata Steel Europe Limited and its subsidiaries, which
More informationTECO Timber Connectors
Tooth Plate Timber Connectors - TCSS & TCDS Single and double sided Tooth Plate Connectors are for improving bolt performance in timber. Timber Connectors are easily installed devices for improving the
More informationDesigned for Building Designed for Living
Designed for Building Designed for iving decorative hardware Add Beauty and Strength to Your Custom Outdoor iving Structures ith Outdoor Accents, a new line of decorative timber connectors and fasteners
More informationTimber to Timber - Timber to Concrete - Timber to Steel
01/2017 TIMBER CONNECTORS NOT TO BE USED IN EXTERIOR SITUATIONS Stainless Steel alternatives are available where stated Timber to Timber - Timber to Concrete - Timber to Steel MiTek manufactures and markets
More informationBuilders Metalwork Product Selector 2018
Builders Metalwork Product Selector 2018 www.bpcfixings.com Manufacturing in the UK since 1977 Contents SMH Timber to Masonry Joist Hangers 4 Timber to Timber Joist Hangers 4 Angle Brackets 6 Restraint
More informationDesigned for Building Designed for Living
decorative hardware Designed for Building Designed for iving (800) 999-5099 strongtie.com Add Beauty and Strength to Your Custom Outdoor iving Structures ith Outdoor Accents, a line of decorative wood
More informationISSUE Erection Manual
Erection Manual The details and information in this book are for guidance of the erection of panels and flooring only. They are not site specific. Refer to the relevant panel drawings for the site, which
More informationDesign Guide Pryda Connectors for Steel Framing
Pryda Connectors for Steel Framing Copyright: (c) Pryda Australia A Division of ITW Australia November 2012 November 2012 Design Guide Pryda Connectors for Steel Framing INDEX General Notes General information
More informationDUTCH GABLE FREESTANDING CARPORT
DUTCH GABLE FREESTANDING CARPORT STRATCO OUTBACK ASSEMBLY INSTRUCTIONS. Your complete guide to building a FREESTANDING Outback DUTCH GABLE CARPORT BEFORE YOU START Carefully read these instructions. If
More information3.1 General Provisions
WOOD FRAME CONSTRUCTION MANUAL 107 3.1 General Provisions 3.1.1 Prescriptive Requirements The provisions of this Chapter establish a specific set of resistance requirements for buildings meeting the scope
More informationPosi-Joist Installation Guide. A guide for storage, handling and installation of the MiTek Posi-Joist floor system
Posi-Joist Installation Guide A guide for storage, handling and installation of the MiTek Posi-Joist floor system Posi-Joist Installation Details A B C D F E A Masonry Wall Connection Details Blockwork
More informationINSTALLATION INSTRUCTIONS for TB6.2,TB7.0, TB7.8 & TB8.4
the unique loft conversion & flooring system INSTALLATION INSTRUCTIONS for TB6.2,TB7.0, TB7.8 & TB8.4 Unit 6, Devizes Trade Centre, Hopton Park, Devizes, Wiltshire, SN10 2EH t 01380 739000 e info@telebeam.co.uk
More informationTOLL FREE:(888) FAX:(941) ASSEMBLY of ProTEC CONCRETE STRUCTURAL INSULATED PANEL
ASSEMBLY of ProTEC CONCRETE STRUCTURAL INSULATED PANEL The ProTEC panels are manufactured with grooves on all four sides to accept the steel components. This grooving applies to the regular panel whose
More informationINSTALLATION GUIDE. Outback. Flat Attached BEFORE YOU START ADDITIONAL MATERIALS TOOLS REQUIRED. VERAnDAHS PATIOS CARPORTS
INSTALLATION GUIDE Outback VERAnDAHS PATIOS CARPORTS Flat Attached BEFORE YOU START It is important to check your Local Government Authority requirements before the installation of your new Stratco Outback
More informationIndex Pipe Hangers and Straps
Index Pipe Hangers and Straps Fig. 1 Standard Clevis Hanger MSS-SP-69, Type 1 WW-H-171E, Type 1 Page 14 Fig. 1CI Clevis Hanger for A.W.W.A. Page 16 Fig. 81 Clevis Hanger WW-H-171E, Type 12 Page 70 Fig.
More informationDowel-type fasteners. Timber Connections. Academic resources. Introduction. Deferent types of dowel-type fasteners. Version 1
Academic resources Timber Connections Dowel-type fasteners Version 1 This unit covers the following topics: Deferent types of dowel-type fasteners Introduction There are four criteria designers should
More informationOUTBACK FLAT ATTACHED VERANDAH PATIO CARPORT - INSTALLATION GUIDE BEFORE YOU START TOOLS REQUIRED ADDITIONAL MATERIALS
BEFORE YOU START It is important to check your Local Government Authority requirements before the installation of your new Stratco Outback Flat Verandah. It is the builder s responsibility to ensure any
More informationWHY YOU SHOULD USE TUFFLOOR. components
Tuffloor DESIGN GUIDE WHY YOU SHOULD USE TUFFLOOR Strong and Easily Installed Tuffloor is a steel floor framing system designed for strength and ease of installation, and is an easy and economical alternative
More informationBEST PRACTICE GUIDE. Socket Bases. Working with Concrete Slabs
Working with Concrete Slabs When working with concrete slabs the barrier protection can be erected in three ways - with socket bases, adjustable slab edge brackets and multi slab clamps. Socket Bases 1
More informationSigma Fasteners, Inc. Section 7
DESCRIPTION PAGE s Wedge s 7-1 Drop-In s 7-2 Single Expansion s 7-2 Machine Screw s 7-2 Lag Shields 7-3 Lead Wood Screw s 7-3 Hammer Drive s 7-4 Hollow Wall Fasteners 7-5 Toggle Bolts 7-6 Toggle Wings
More informationFASTENERS BUILDING DEPARTMENT
FASTENERS BUILDING DEPARTMENT 952-446-1660 WWW.CITYOFMINNETRISTA.COM This handout is intended only as a guide and is based in part on the 2015 Minnesota Residential Code, Minnetrista City ordinances, and
More informationCall (770) STEP 6: Caulk bolt hole within the bracket for protection from the elements.
Call (770) 777 7007 Structural Deck Support System: Product Numbers: H1-GQ, H2-GCL (Also applies to H1-GK and H2-GCR) STEP 1: Following the spacing guidelines per the deck design and joist layout, mark
More informationENGINEERED BUILDING PRODUCTS. CycloneTie CT1200 CT900 CT600 CT400 CT180. mitek.com.au
ENGINEERED BUILDING PRODUTS yclonetie T1200 T900 T600 T400 T180 mitek.com.au Ti e FOR ROOF SEURITY UNDER EXTREME WIND ONDITIONS APPLIATION: ycloneties are used to secure purlins, rafters and trusses to
More informationSite Installation Guide
Site Installation Guide Site Checklist Stop and read this now. Tick box when checked. Floor Joist Layout If a floor joist design/layout was done, was a site copy of the layout provided with the joists,
More informationJOIST DETAILS Plate nail, 16d (0.15" x 1 ") at 1 on-center Blocking panel: 1 1 8" TJ Rim Board, 1 1 TimberStrand SL or TJI joist Toe nail, 10d (0.11" x ") at on-center A1 CS BEAM DETAILS L1 eb stiffener
More informationProducts for fixing to Steelwork and Decking
Products 8.0 Beam Clamp - Single Support 8.1 Universal Joint for any variable Angle Adjustment 8.2 Beam Clamp TCS for Header Rails 8.3 Beam Clip for Cross Support/ Dimensioning of Bolts 8.4 Beam Clip for
More informationSecuAnch Roof Anchor System
Height Safety Products Email: marketing@fallprotec.com SecuAnch Roof Anchor System 1 Presentation The SecuAnch lifeline is designed to be permanently installed on buildings and other structures where maintenance
More informationDura-Lock Roof System
DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.
More informationGLOSSARY OF TERMS SECTION 8
GLOSSARY OF TERMS SECTION 8 Anchor Bolt Angle Base Plate Bay Blocking CCB Centerline Chord Cladding Clip Closure Strip An A-307 steel bolt embedded in the concrete footing to anchor the base plate of the
More informationMODERN PERGOLA INSTALLATION GUIDE. When only the best will do.
MODERN PERGOLA INSTALLATION GUIDE When only the best will do. TOOLS LIST Drill(s) 3/8" Magnetic Driver (s) 12" Drill Extension #2 Square Drive bit for Drill or Driver Level Tape Measure Hammer Drill if
More informationSections & Details. WOOD SILL and FLOOR CONSTRUCTION NOTES
2 Sections & Details WOOD SILL and FLOOR CONSTRUCTION NOTES 1 Commonly Used Lumber Common LENGTHS include: 8, 10, 12, 14, 16 NOMINAL SIZES 2 x 4 2 x 6 2 x 8 2 x 10 2 x 12 ACTUAL SIZES 1 ½ x 3 ½ 1 ½ x 5
More informationPryda Timber Connectors
Pryda Timber Connectors Pryda Lintel Guide Engineered Steel Wall Lintels March 2014 ESSENTIAL NOTES PRYDA PRODUCT GUIDES INTRODUCTION The information in this Product Guide is provided for use in Australia
More informationREGENCY TIMBER BUILDINGS
REGENCY TIMBER BUILDINGS TEL 01948 830460 UNIT 22 PENLEY IND EST, PENLEY.WREXHAM. LL13 0LQ 1 Garage fitting instructions Tools needed handsaw, hammer, Stanley knife with hook blade, tape measure, battery
More informationCURVED ROOF ASSEMBLY INSTRUCTIONS ATTACHED VERANDAH. Your supplementary guide to building an ATTACHED CURVED ROOF VERANDAH or PATIO BEFORE YOU START
ROOF ATTACHED VERANDAH ASSEMBLY INSTRUCTIONS Your supplementary guide to building an ATTACHED ROOF VERANDAH or PATIO This set of instructions should be used in conjunction with the Stratco instruction
More informationDescription. Lesson Outcomes. Assumptions. Build a Floor. Carpenter
Carpenter Description Floors are an integral part of residential construction and must be built to specifications that meet building code requirements. In this Activity Plan, students will be cutting and
More informationREAD BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION
edium + Heavy duty READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Pay attention to danger and safety notices. be exposed: Carefully
More informationInstallation Instructions
edium + Heavy duty READ BEFORE INSTALLING UNIT Preliminary instructions: 1. Check window opening size: the mounting parts furnished with this air conditioner are made to install in a wooden sill double-hung
More informationInstallation Instructions
For Medium (15-18.5K) + Heavy duty (22-28.5K) Air Conditioner READ BEFORE INSTALLING UNIT To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp
More informationInstallation guide for 20/20
Introduction The following installation instructions are recommended minimum requirements for the 20/20. The designer and fixer should ensure that tiles are installed in accordance with BS 5534; The British
More informationAcceptable Standards of Domestic Construction
Truss or Rafter Roof Batten Triple grip fastener (for roof trusses) Foil lined Insulation blanket Top plate Sprocket Brick tie Top plate strapping at 1200mm max. cts. Note: Holding down straps should be
More informationA Shell construction
A Shell construction A 4/2012 Content 1 BASE AND WALL ANCHORING 1.1 Base with mortar bed 1.2 Base with sill plate 1.3 Base with raised sill plate 1.4 Concrete base (mortar bed) 1.5 Concrete base (sill
More informationTrack Rack. * Track Racks are not lockable
The Track Rack s unique staggered, sliding hook design creates the greatest parking efficiency while still providing easy access to any particular bike. When adding or removing a bike to the rack, simply
More informationSECTION R507 DECKS DECKING LEDGER BOARD BEAM. FOOTING BEAM SPAN CANTILEVER For SI: 1 inch = 25.4 mm FIGURE R507.2 DECK CONSTRUCTION
SECTION R507 DECKS R507.1 Application. The provisions of this section shall provide prescriptive requirements for the design and construction of all uncovered, wood-framed, single-span exterior decks.
More informationHow-To-build guide Garden shed
How-To-build guide Garden shed What you can build using this guide This guide will show you how to build a re-locatable garden shed. Before you begin building Contact your local territorial authority to
More informationPryda Timber Connectors
Pryda Timber Connectors A complete guide to the design, specification and installation of Pryda High Capacity Products March 2012 ESSENTIAL NOTES PRYDA PRODUCT GUIDES INTRODUCTION The information in this
More information12X20 Breeze Pergola Assembly Manual Outdoor Living Today
12X20 Breeze Pergola Assembly Manual Outdoor Living Today Revision #10 July 21th, 2015 Note: Post Mounting Hardware is NOT included in this kit. Please confirm with your local building permit office to
More informationCLEARSPAN GABLE STRATCO OUTBACK ASSEMBLY INSTRUCTIONS. WITH GAZEBO END ATTACHED PATIO
CLEARSPAN GABLE WITH GAZEBO END ATTACHED PATIO STRATCO OUTBACK ASSEMBLY INSTRUCTIONS. Your supplementary guide to building an ATTACHED CLEARSPAN GABLE VERANDAH or PATIO WITH GAZEBO END This set of instructions
More information50948-RHN Putney. 06 January This document includes: Aluminium strip/ sheet coverings/ flashings 1. Code Section Revision Dated
50948-RHN Putney 06 January 2018 This document includes: Code Section Revision Dated H72 Aluminium strip/ sheet coverings/ flashings 1 Table of Contents Title H72 Aluminium strip/ sheet coverings/ flashings
More informationTECHNICAL MANUAL. TERADOWEL and ULTRADOWEL. Reliable Dowel System for Floor Joints
TECHNICAL MANUAL TERADOWEL and ULTRADOWEL Reliable Dowel System for Floor Joints Version: PEIKKO GROUP 11/2018 TERADOWEL and ULTRADOWEL Reliable Dowel System for Floor Joints Dowels manufactured from high
More informationINSTALLATION GUIDE
MASON S BRICK INSTALLATION GUIDE 800.945.4440 WWW.STYLECRESTINC.COM MASON S BRICK INSTALLATION GUIDE INSTALLATION SUMMARY Your new Mason s Brick skirting comes in 4-1/2 foot long panels that are either
More informationUPPER FLOORS TIMBER AND CONCRETE
UPPER FLOORS TIMBER AND CONCRETE FUNCTIONS OF AN UPPER FLOOR Functions: Support imposed loads Not deflect under load Strength and stability Provide restraint for external walls Fire resistance (30 minutes)
More informationeb^sv=qfj_bo UNIVERSITY OF WISCONSIN - STOUT COLLEGE OF SCIENCE TECHNOLOGY ENGINEERING & MATHEMATICS Architectural Technology AEC 233
eb^sv=qfj_bo UNIVERSITY OF WISCONSIN - STOUT COLLEGE OF SCIENCE TECHNOLOGY ENGINEERING & MATHEMATICS Architectural Technology AEC 233 Dr. Jason E. Charalambides fkqolar`qflk Heavy timber construction consists
More informationVERSA-LAM. An Introduction to VERSA-LAM Products
44 VERSA-LAM An Introduction to VERSA-LAM Products VERSA-LAM is one of the strongest and stiffest engineered wood products approved in the UK. 241 302 356 406 VERSA-LAM products are excellent as floor
More informationFixings. Products - Fixings.
Fixings Our range of fixing products cater for every drywall need, ensuring simple yet secure fixing of plasterboard and metal framing. The range includes Gyproc screws, engineered for board-to-metal,
More informationPRODUCT INFORMATION MANUAL SECTION: 16 FIXED METAL AWNINGS FIXED METAL AWNINGS
FIXED METAL AWNINGS Fixed Metal Awnings BAHAMA Maximum Width Minimum Width Minimum projection Minimum Drop TS - Truss Support Maximum Overhang Minimum Overhang Unlimited 500mm TS=1601mm PS=2847mm PS=
More informationFitting instructions for (Read instructions fully, before installing the door)
t;t;i~iij~1~ti1i1f~~jhij~!~ti~~f~~t~il~t~11f;'~rj~*:i1;~i;~~g~1!~t4rf~?' ~~a~ Fitting instructions for (Read instructions fully, before installing the door) Horizontal tracked doors supplied with ' Retractable
More informationENGINEERED BUILDING PRODUCTS. SplitHanger. mitek.com.au
ENGINEERED BUILDING PRODUCTS SplitHanger mitek.com.au S p l i t H a n g e r SUITABLE FOR VARIOUS WIDTHS OF TIMBER BEAM APPLICATION: SplitHangers are versatile hangers that provide a heavy duty connection
More informationSTRUCTURAL BRACKETS CATALOGUE
08/2011 STRUCTURAL BRACKETS CATALOGUE SUPERIOR QUALITY, HOT DIP GALVANISED, HEAVY DUTY BRACKETS FOR FIXING TIMBER TO TIMBER, TIMBER TO CONCRETE, TIMBER TO STEEL The BOWMAC product range is designed to
More informationWindload Post 9100/9600/9900 Installation Instructions
Windload Post 9100/9600/9900 Installation Instructions Wayne Dalton, a division of Overhead Door Corporation P.O. Box 67, Mt. Hope, OH 44660 www.wayne-dalton.com Wayne-Dalton Corp. P.O. Box 67 Mt. Hope,
More informationTRADITIONAL GABLE ATTACHED PATIO AND CARPORT. Your complete guide to building an ATTACHED Outback TRADITIONAL GABLE PATIO or CARPORT
TRADITIONAL GABLE ATTACHED PATIO AND CARPORT STRATCO OUTBACK ASSEMBLY INSTRUCTIONS. Your complete guide to building an ATTACHED Outback TRADITIONAL GABLE PATIO or CARPORT BEFORE YOU START Carefully read
More information8X10 Breeze Pergola Assembly Manual Outdoor Living Today
8X10 Breeze Pergola Assembly Manual Outdoor Living Today Revision #11 Jan 18th, 2018 Note: Post Mounting Hardware is NOT included in this kit. Please confirm with your local building permit office to determine
More informationVINYL CLASSIC FREESTANDING PERGOLA ASSEMBLY INSTRUCTIONS
P a g e 1 VINYL CLASSIC FREESTANDING PERGOLA ASSEMBLY INSTRUCTIONS Shown: 8' x 12' Vinyl Classic Pergola with 12" Top and Main Runner Spacing The design of this pergola is based on all posts being installed
More informationTechnical Innovation in Steelwork Connections
Established 1934 Technical Innovation in Steelwork Connections 2 Introduction to Lindapter Welcome For over 80 years Lindapter has earned a respected reputation as the pioneer of designing and manufacturing
More informationHOME STRENGTHENING GUIDE HOW TO ECONOMICALLY STRENGTHEN YOUR HOUSE AGAINST EARTHQUAKES AND HURRICANES
HOME STRENGTHENING GUIDE HOW TO ECONOMICALLY STRENGTHEN YOUR HOUSE AGAINST EARTHQUAKES AND HURRICANES Grenville W Phillips II BSc, BEng, MASc, MURP, CEng, FIStructE, FCIHT, MAPM, MCSCE, MBAPE Chartered
More information10X12 Arched Breeze Pergola Assembly Manual Outdoor Living Today
10X12 Arched Breeze Pergola Assembly Manual Outdoor Living Today ITEM# BZ1012ARCH Revision 2 March 25th/2015 Note: Post Mounting Hardware is NOT included in this kit. Please confirm with your local building
More informationTimber Connectors & Post Anchors. Click to start
Timber Connectors & Post Anchors Click to start Pryda Pryda has been an integral part of the building industry in Australia for over 40 years, particularly in timber truss and frame solutions with the
More informationSWAY BRACE PIPE ATTACHMENT FIG. 010
Function: Designed for bracing pipe against sway and seismic disturbance. The pipe attachment component of a sway brace system used in conjunction with a PHD Manufacturing structural attachment fitting,
More informationChapter 7 - Porch Framing
Chapter 7 - Porch Framing Contents Chapter 7 - Porch Framing... 7-1 Timing & Prerequisites... 7-2 Concrete Porches Caps (Contractor)... 7-3 Organize the Porch Framing Lumber... 7-3 Types of Porch Roofs...
More informationCabonyx Installation Manual
Cabonyx Installation Manual Content Deck-Nyx and Plan-Nyx Installation Page 1 Flooring Products Page 1 Accessories Page 1 Installation Tools Page 2 Preparing Sub-structure Page 2 Installation Page 4 Cautions
More informationCopper Tubing Hangers Clevis Hangers. Copper Tubing Hangers
Copper Tubing Hangers Clevis Hangers Copper Tubing Hangers Fig. CT-69 Adjustable Swivel Rug Fig. CT-138R Fig. CT-65 Fig. CT-109 Extension Split Light Weight Adjustable Clevis Fig. CT-99 & CT-99C Split
More informationHow to Build Good Decks..
How to Build Good Decks.. Worldwide Sleeping Company, Inc Cary, North Carolina Decking Overview.. Decking Overview.. more Decking Joist.... Joist Hanger Ledger Lag Screw House Wall Decking House Floor
More informationA E D X E X C A C B A L B E L E T R T A R Y
ADE CABE TAY Adex Cable Tray Metallic Adex cable trays are manufactured for the smooth and easy pulling of cable from one point to another to BS EN 61537:2002. e have designed the best cable trays, by
More informationAssembly Instructions 10 X 10 Aluminum Frame Building
Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal
More informationMULTISPAN GABLE WITH HIP END ATTACHED PATIO
MULTISPAN GABLE WITH HIP END ATTACHED PATIO STRATCO OUTBACK ASSEMBLY INSTRUCTIONS. Your supplementary guide to building an ATTACHED MULTISPAN GABLE VERANDAH or PATIO WITH HIP END This set of instructions
More informationHALLOWELL HI-TECH SHELVING
LLOLL I-C SLVING i-ech Industrial grade steel shelving continues a tradition of quality established generations ago with the goal of providing a shelving line with the strength needed to handle most industrial
More informationIntex Engineered Pergola System Installation Instructions. NOTE: See Appendix for Foundation Requirements
Intex Engineered Pergola System Installation Instructions NOTE: See Appendix for Foundation Requirements Pergola Installation, Freestanding (If pergola will be attached-to-structure, skip to page 3) 1.
More informationA Reference Guide. Continuous Hinge, Inventory and Service Worldwide Est End Play Design Engineering with Standard Continuous Hinges
Hinge Width Paint Clearance Knuckle Length End Play Design Engineering with Standard Continuous Hinges A Reference Guide Knuckle Dear Design Engineer or Purchasing Agent, We frequently see blueprints for
More informationGlulam Connection Details
T E C H N I C A L N O T E Glulam Connection Details Note: This version is superseded by a more current edition. Check the current edition for updated design and application recommendations. ENGINEERED
More informationInstallation of Balustrade Systems
Installation of Balustrade Systems IMPORTANT: Be sure to mark the center point of each newel post's location prior to installation to insure proper spacing. All product interfaces must use PL Premium Adhesive
More informationmanthorpe Roll-Out Dry Fix Ridge System building products Fixing Instructions MBP 8265e
manthorpe building products Roll-Out Dry Fix Ridge System Fixing Instructions MBP 8265e Ridge Details Fig A. Assembly View of Dry Ridge Detail s/s screw clamping plate rubber washer foam spacer ridge tile
More informationInstallation Manual For ToddPod Outdoor Shower Enclosures
Installation Manual For ToddPod Outdoor Shower Enclosures Contact us at 888-545-9763 or email us at office@toddpod.com with any questions during the installation process. Our service team is available
More informationDeck Evaluation Checklist
Date: Reported By: Project Name/Client: Year Deck was Built: I. Stairs A. Not Applicable B. Are there any visible signs of cracks, decay or over-notching? No Yes 1. If yes, where? C. Stairway width: (Hint:
More informationThe Influence of Nails and Plasterboard on the Racking Resistance of Stud Walls
Building 1 Grosvenor Court, Hipley Street OLD WOKING, SURREY GU22 9LL Tel: +44 (0) 1483 769518 Fax: +44 (0) 1483 770863 E-mail: design@silvatecdesigncom Internet: wwwsilvatecdesigncom The Influence of
More informationSTRUCTURAL BRACKETS CATALOGUE
0/2 STRUCTURAL BRACKETS CATALOGUE SUPERIOR QUALITY, HOT DIP GALVANISED, HEAVY DUTY BRACKETS FOR FIXING TIMBER TO TIMBER, TIMBER TO CONCRETE, TIMBER TO STEEL The BOWMAC product range is designed to cut
More informationtable of contents Sliding Door Accessories Page Latches & Snuggers Stay Rollers Brackets & Stops
table of contents Square Track & Accessories Pages 4-7 Square Track Options Page 4 Light Duty Track Page 4 Square Track Brackets Page 5 Square Track Accessories Page 5 Square Track Trolleys Page 6-7 Offset
More informationMain Floor Revisions: 38' 0" Rm1 H3 50' 0" Bk1 B1 Rm2 B5 (26)-2 H2 B2 H3 (3)-3 B3 (11)-4 Bk1 B1 (5)-5 Rm4 Bk1 Rm3 Bk1 24' 0" 6' 0" 20' 0" START FRAMIN
Main Floor Revisions: 38' 0" Rm1 H3 50' 0" B1 Rm2 B5 (26)-2 H2 B2 H3 (3)-3 B3 (11)-4 B1 (5)-5 Rm4 Rm3 24' 0" 6' 0" 20' 0" START FRAMING HERE 18" BCI 90'S @ 16"OC Products PlotID Net Qty Product Length
More informationAvailable from. Established Technical Innovation in Steelwork Connections
Established 1934 Technical Innovation in Steelwork Connections 2 Introduction to Lindapter Welcome For over 80 years Lindapter has earned a respected reputation as the pioneer in the design and manufacture
More informationThe WANZ Guide to Window Installation
The WANZ Guide to Window Installation as described in E2/AS1 Amendment 5 1 October 2012 Ver. 1.2 Window Association of New Zealand Page 2 of 74 Contents Overview Page 5 Objective Page 5 Scope Page 5 Opening
More informationLateral Support. Decks over 24 above grade require lateral support* *Exceptions to be discussed later
Lateral Support Decks over 24 above grade require lateral support* *Exceptions to be discussed later Decking Types of Decking: -2x4s & 2x6s -five quarter span rated decking boards -Wood plastic composite
More informationLVL8 H1.2 GENERAL FRAMING. Eco Friendly Revolutionary H1.2 Treatment Azotek by Zelam
LVL8 H1.2 GENERAL FRAMING Eco Friendly Revolutionary H1.2 Treatment Azotek by Zelam NPIL/MARCH2015 Introduction to NelsonPine LVL8 H1.2 NelsonPine LVL is an engineered wood composite made from rotary peeled
More informationButt Two pieces of wood meeting with flat sides adjoining usually at right angles. Some type of connector is needed to prevent movement.
Wood Connections There are basically five different types of connectors: Interlocking (carpentry joints), Dowel, Metal Connectors, Special Formed Connectors and Adhesives. I Interlocking (Carpentry Joints)
More informationStratco Sanctuary INSTALLATION BEFORE YOU START TOOLS REQUIRED GUIDE
INSTALLATION GUIDE Stratco Sanctuary Verandahs, Patios and Carports BEFORE YOU START It is important to check with your Local Government Authority prior to the installation of your new Stratco Sanctuary
More informationExtra Wide Designer Lockers Series Installation Instructions
Extra Wide Designer Lockers 20000 Series Thank you for selecting the 20000 Series Extra Wide Designer Lockers. We are confident that the quality and construction of the lockers will prove to be a good
More informationWith Illustrations, Drawings & Step By Step Details. Click Here To Download 12,000 Shed Plans. 1 P a g e Download 12,000 More Shed Plans
With Illustrations, Drawings & Step By Step Details Click Here To Download 12,000 Shed Plans 1 P a g e Download 12,000 More Shed Plans Table of Contents OVERVIEW... 3 MATERIALS & CUTTING LISTS... 4 DRAWINGS,
More informationEquilibrium. Conference Table. Installation Instruction. Revision B 11/07/16
Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete
More informationASSEMBLY INSTRUCTIONS SS2520. BASE SIZE: 2.520m x 2.020m
ASSEMBLY INSTRUCTIONS SS50 BASE SIZE:.50m x.00m CONGRATULATIONS ON PURCHASING A SMART STORE SHED. BEFORE YOU BEGIN THE ASSEMBLY PLEASE NOTE SOME IMPORTANT POINTS: BEFORE YOU START: Read all instructions
More informationSINGLE TRACK BYPASS (patent pending) barn door hardware
SINGLE TRACK BYPASS (patent pending) barn door hardware Installation Manual What is included in your kit: Part number Part name Quantity 1 Inner door hanger 2 2 Outer door hanger 2 3 5/16 x 1.5 lag bolts
More information