Product Dimensions (mm) Overall length (including any bend) Pre Galvanised - 1.4mm thick x 36mm wide. Declared values for the TRS strap
|
|
- Chester Wiggins
- 5 years ago
- Views:
Transcription
1 TECO Straps TRS The Ron Sammons The Ron Sammons is lightweight to handle yet retains its structural strength so it can be used instead of a traditional Heavy Duty Strap for providing lateral restraint of roof trusses, rafters and joists tied to masonry and for vertical applications such as holding down the wall plate. Designed to The Building Regulations BS 5268 Part 3 and other building standards for lateral restraint. Lightweight design makes it easier to handle. No need to notch joists making it easier and quicker to install. Easier to build into brickwork courses. More cost effective when compared to the traditional Heavy Duty Strap and Heavy Edge Rolled Strap. TRS TRS The Ron Sammons Galvanised steel EN G600. Manufactured to EN 845-1:2013. Tested by Lucideon Ltd Notification Body No For horizontal applications Use min 6 no x 30mm square twist nails or equivalent fixed to timber joists/rafters. Dimensions (mm) Overall length (including any bend) Pre Galvanised - 1.4mm thick x 36mm wide TRS600B TRS800B TRS0B TRS1200B TRS1500B TRS1600B Declared values for the TRS strap Fixed to timber joists with noggings Fixed to I-joists with noggings 9.5kN 9.2kN Tel Fax mm deflection at 1/3rd of this load 1.5mm deflection at 1/3rd of this load sales@tecoproducts.co.uk 1
2 LD, HD, ER, LDTF & HDTF Traditional Straps Traditional Heavy and Light Duty Restraint Straps designed to The Building Regulations BS 5268 Part 3 and other building standards for vertical (LD) restraint or lateral (HD) restraint. Light Duty - LD Light Duty Restraint Straps are generally for vertical applications such as holding down a wall plate. Heavy Duty - HD Heavy Duty Restraint Straps are generally for horizontal applications providing lateral restraint of roof trusses, rafters and joists tied to masonry. Light Duty Straps Popular stock sizes are listed on the following page but straps can be ordered to any length up to 15m. Holed 6mm at 25mm offset centres. Available in galvanised or stainless steel. HD Bent Galvanised steel EN DX51D Z275 or grade austenitic stainless steel. Manufactured to EN 845-1:2013. Tested by CERAM Research Ltd Notification Body No HD Bent & Twisted Light Duty - LD When used as a vertical restraint to hold down a wall plate use a minimum length of 900mm. For galvanised straps use min 10 no x 30 square twist nails or 6 no. 4 x 40 screws (drilled and plugged) into the masonry. Use min 2 no x 30 square twist nails into wall plate. For stainless steel straps use min 10 no x 30 annular ring shank nails stainless steel or 6 no. 4 x 40 stainless steel screws (drilled and plugged) into the masonry. Use min. 2 no. 30 x 3.75 annular ring shank nails into wall plate. Heavy Duty - HD For galvanised straps use min 7 no x 30 square twist nails or equivalent fixed to timber joists / rafters. For stainless steel use min 7 no x 30 annular ring shank stainless steel nails or equivalent fixed to timber joists/rafters. Twisted Strap Bent Strap Flat Strap 2
3 Light Duty Straps Popular stock sizes are listed below but straps can be ordered to any length up to 15m. Stainless steel and bent & twisted straps are on page 5 of this literature. Pre Galvanised - 2.4mm Dimensions (mm) Overall length including bend or twist or twist LD200B50 Light Duty Galv Bent LD300B Light Duty Galv Bent 300 LD400B Light Duty Galv Bent 400 LD450B Light Duty Galv Bent 450 LD600B Light Duty Galv Bent 600 LD800B Light Duty Galv Bent 800 LD900B Light Duty Galv Bent 900 LD0B Light Duty Galv Bent 0 LD1200B Light Duty Galv Bent 1200 LD1200B150 Light Duty Galv Bent LD1400B Light Duty Galv Bent 1400 LD1600B Light Duty Galv Bent 1600 LD200F Light Duty Galv Flat LD220F Light Duty Galv Flat LD250F Light Duty Galv Flat LD300F Light Duty Galv Flat LD400F Light Duty Galv Flat LD600F Light Duty Galv Flat LD800F Light Duty Galv Flat LD900F Light Duty Galv Flat LD0F Light Duty Galv Flat 0 - LD1F Light Duty Galv Flat 1 - LD1200F Light Duty Galv Flat LD1400F Light Duty Galv Flat LD1600F Light Duty Galv Flat LD3000F Light Duty Galv Flat LD3600F Light Duty Galv Flat LD600T Light Duty Galv Twisted 600 LD600T150 Light Duty Galv Twisted LD750T Light Duty Galv Twisted 750 LD800T Light Duty Galv Twisted 800 LD900T Light Duty Galv Twisted 900 LD900T150 Light Duty Galv Twisted LD0T Light Duty Galv Twisted 0 LD0T150 Light Duty Galv Twisted LD1200T Light Duty Galv Twisted
4 Heavy Duty Straps Popular stock sizes are listed below but straps can be ordered to any length up to 15m. Stainless steel and bent & twisted straps are on page 5 of this literature. Edge Coated Galvanised Steel - 4mm Overall length including bend or twist Dimensions (mm) HD400B Heavy Duty Galv Bent 400 HD600B Heavy Duty Galv Bent 600 HD600B150 Heavy Duty Galv Bent HD800B Heavy Duty Galv Bent 800 HD800B150 Heavy Duty Galv Bent HD900B Heavy Duty Galv Bent 900 HD900B150 Heavy Duty Galv Bent HD0B Heavy Duty Galv Bent 0 HD0B150 Heavy Duty Galv Bent HD1200B Heavy Duty Galv Bent 1200 HD1200B150 Heavy Duty Galv Bent HD1300B Heavy Duty Galv Bent 1300 HD1300B150 Heavy Duty Galv Bent HD1400B150 Heavy Duty Galv Bent HD1500B Heavy Duty Galv Bent 1500 HD1500B150 Heavy Duty Galv Bent HD1600B Heavy Duty Galv Bent 1600 HD1600B150 Heavy Duty Galv Bent HD1800B150 Heavy Duty Galv Bent HD300F Heavy Duty Galv Flat HD400F Heavy Duty Galv Flat HD600F Heavy Duty Galv Flat HD800F Heavy Duty Galv Flat HD0F Heavy Duty Galv Flat 0 - HD1200F Heavy Duty Galv Flat HD1300F Heavy Duty Galv Flat HD1400F Heavy Duty Galv Flat HD1500F Heavy Duty Galv Flat HD1600F Heavy Duty Galv Flat HD1800F Heavy Duty Galv Flat HD2000F Heavy Duty Galv Flat HD3000F Heavy Duty Galv Flat HD3600F Heavy Duty Galv Flat HD4000F Heavy Duty Galv Flat HD400T Heavy Duty Galv Twisted 400 HD600T Heavy Duty Galv Twisted 600 HD800T Heavy Duty Galv Twisted 800 HD0T Heavy Duty Galv Twisted 0 HD0T150 Heavy Duty Galv Twisted HD1200T Heavy Duty Galv Twisted 1200 HD1200T150 Heavy Duty Galv Twisted HD1400T Heavy Duty Galv Twisted 1400 HD1500T150 Heavy Duty Galv Twisted HD1600T Heavy Duty Galv Twisted
5 Stainless Steel Straps Popular stock sizes are listed below but straps can be ordered to any length up to 15m. Dimensions (mm) Overall length including bend Light Duty Stainless Steel - 2.4mm LDSS600B Light Duty Stainless Bent 600 LDSS900B Light Duty Stainless Bent 900 LDSS0B Light Duty Stainless Bent 0 LDSS1200B Light Duty Stainless Bent 1200 LDSS1600B Light Duty Stainless Bent 1600 LDSS600F Light Duty Stainless Flat LDSS900F Light Duty Stainless Flat LDSS0F Light Duty Stainless Flat 0 - LDSS1200F Light Duty Stainless Flat LDSS1600F Light Duty Stainless Flat LDSS600T Light Duty Stainless Twisted 600 LDSS900T Light Duty Stainless Twisted 900 LDSS0T Light Duty Stainless Twisted 0 LDSS1200T Light Duty Stainless Twisted 1200 Heavy Duty Stainless Steel - 4mm HDSS600B Heavy Duty Stainless Bent 600 HDSS900B Heavy Duty Stainless Bent 900 HDSS0B Heavy Duty Stainless Bent 0 HDSS1200B Heavy Duty Stainless Bent 1200 HDSS1600B Heavy Duty Stainless Bent 1600 HDSS600F Heavy Duty Stainless Flat HDSS900F Heavy Duty Stainless Flat HDSS0F Heavy Duty Stainless Flat 0 - HDSS1200F Heavy Duty Stainless Flat HDSS1600F Heavy Duty Stainless Flat HDSS600T Heavy Duty Stainless Twisted 600 HDSS900T Heavy Duty Stainless Twisted 900 HDSS0T Heavy Duty Stainless Twisted 0 HDSS1200T Heavy Duty Stainless Twisted 1200 HDSS1600T Heavy Duty Stainless Twisted 1600 Bent & Twisted Straps Popular stock sizes are listed below but straps can be ordered to any length up to 15m. Dimensions (mm) Overall length Distance between Light Duty Pre Galvanised 2.4mm LD0BT Light Duty Galv Bent & Twist 0 LD1200BT Light Duty Galv Bent & Twist 1200 Heavy Duty Edge Coated Galvanised Steel - 4mm HD600B150T Heavy Duty Galv Bent & Twisted HD800B150T Heavy Duty Galv Bent & Twisted HD0BT Heavy Duty Galv Bent & Twisted 0 HD0B150T Heavy Duty Galv Bent & Twisted HD1200BT Heavy Duty Galv Bent & Twisted 1200 HD1200B150T Heavy Duty Galv Bent & Twisted HD1400B150T Heavy Duty Galv Bent & Twisted HD1600B150T Heavy Duty Galv Bent & Twisted
6 TECO Heavy Edge Rolled Straps The ER Strap has rolled edges along the entire strap making it feel substantial for those that prefer a more traditional strap without the full cost. In tests the TECO ER Strap performed equally as well as or better than the equivalent traditional 5mm Heavy Duty Strap, providing lateral restraint of roof trusses, rafters and joists tied to masonry. Designed to The Building Regulations BS 5268 Part 3 and other building standards for lateral restraint. Lighter design makes it easier to handle. More cost effective when compared to the traditional heavy duty strap. Available flat, bent or twisted. 2.5mm thick rolled to 5mm. 30mm wide. Holed 6mm at 25mm offset centres. ER Galvanised steel EN DX51D Z275, manufactured to EN 845-1:2013. Tested by CERAM Research Ltd Notification Body No ER Bent When used as a lateral restraint; use min 6 no. 4 x 75 round wire nails or equivalent fixed to timber joists/rafters. Dimensions (mm) Overall length (including any bend) Pre Galvanised - 2.4mm ER600B Edge Rolled Bent 600 ER600B150 Edge Rolled Bent ER0B Edge Rolled Bent 0 ER0B150 Edge Rolled Bent ER1200B Edge Rolled Bent 1200 ER1200B150 Edge Rolled Bent ER1600B Edge Rolled Bent 1600 ER1600B150 Edge Rolled Bent ER1800B Edge Rolled Bent 1800 ER1800B150 Edge Rolled Bent ER2000B150 Edge Rolled Bent ER600F Edge Rolled Flat ER0F Edge Rolled Flat 0 - ER1200F Edge Rolled Flat ER1400F Edge Rolled Flat ER1600F Edge Rolled Flat ER1800F Edge Rolled Flat ER600T Edge Rolled Twisted 600 ER0T Edge Rolled Twisted 0 ER1200T150 Edge Rolled Twisted ER1600T150 Edge Rolled Twisted ER1800T Edge Rolled Twisted 1800 EDGE ROLLED STRAP 6
7 TECO Timber Frame Straps The Timber Frame Strap is a holding down strap providing restraint against uplift to timber frames. Holed 6mm at 25mm offset centres. Available in two thicknesses. Available in both galvanised and stainless steel. Light Duty - Stainless Steel only Grade austenitic stainless steel to EN Heavy Duty - Galvanised or Stainless Steel Edge coated galvanised steel EN DX51D Z600 or grade austenitic stainless steel to EN Use appropriate fixings. Always ensure that compatible corrosion resistant fixings are used, i.e. do not use galvanised fixings with stainless steel products or vice versa. Thickness Dimensions LDTFSS Overall length Pre Galvanised HDTF Timber Frame Strap Stainless Steel LDTFSS Timber Frame Strap HDTFSS Timber Frame Strap TIMBER FRAME STRAP 7
SINGLE PIECE MASONRY HANGERS
SINGE PIECE MASONRY ANGERS TECNICA DATA SEET The FM Single Piece Joist anger is designed to support timber joists built in to brick or block walls with a minimum crushing strength of 3.5N/mm². They are
More informationF I X I N G B R O C H U R E
F I X I N G B R O C H U R E Joist Hangers Joist Hangers on Steel Beams Fixing Masonry Hangers Speedy Joist Hangers Lateral Restraint Straps Roof Tie Down Straps Herring Bone Joist Strut Bat 'U' Nail Plate
More informationTECO Timber Connectors
Tooth Plate Timber Connectors - TCSS & TCDS Single and double sided Tooth Plate Connectors are for improving bolt performance in timber. Timber Connectors are easily installed devices for improving the
More informationCatnic Pontypandy Industrial Estate Caerphilly CF83 3GL T: F: English version
www.catnic.com Care has been taken to ensure that the contents of this publication are accurate, but Tata Steel Europe Limited and its subsidiaries, which includes Tata Steel UK Limited, do not accept
More informationBuilders Metalwork Product Selector
www.catnic.com Builders Metalwork Product Selector September 2015 Care has been taken to ensure that the contents of this publication are accurate, but Tata Steel Europe Limited and its subsidiaries, which
More informationENGINEERED BUILDING PRODUCTS. CycloneTie CT1200 CT900 CT600 CT400 CT180. mitek.com.au
ENGINEERED BUILDING PRODUTS yclonetie T1200 T900 T600 T400 T180 mitek.com.au Ti e FOR ROOF SEURITY UNDER EXTREME WIND ONDITIONS APPLIATION: ycloneties are used to secure purlins, rafters and trusses to
More informationTimber to Timber - Timber to Concrete - Timber to Steel
01/2017 TIMBER CONNECTORS NOT TO BE USED IN EXTERIOR SITUATIONS Stainless Steel alternatives are available where stated Timber to Timber - Timber to Concrete - Timber to Steel MiTek manufactures and markets
More informationENGINEERED BUILDING PRODUCTS. SplitHanger. mitek.com.au
ENGINEERED BUILDING PRODUCTS SplitHanger mitek.com.au S p l i t H a n g e r SUITABLE FOR VARIOUS WIDTHS OF TIMBER BEAM APPLICATION: SplitHangers are versatile hangers that provide a heavy duty connection
More informationDesign Guide Pryda Connectors for Steel Framing
Pryda Connectors for Steel Framing Copyright: (c) Pryda Australia A Division of ITW Australia November 2012 November 2012 Design Guide Pryda Connectors for Steel Framing INDEX General Notes General information
More informationSTRUCTURAL BRACKETS CATALOGUE
0/2 STRUCTURAL BRACKETS CATALOGUE SUPERIOR QUALITY, HOT DIP GALVANISED, HEAVY DUTY BRACKETS FOR FIXING TIMBER TO TIMBER, TIMBER TO CONCRETE, TIMBER TO STEEL The BOWMAC product range is designed to cut
More informationVertical Offset Base and Safety Rail System Installation Instructions
Section 5 Vertical Offset Base and Safety Rail System Installation Instructions The vertical offset base and safety rail assembly are designed to be used in residential construction for sloped or flat
More informationIn straight, not in skew
In straight, not in skew Helical Nails for Warm Roof Construction 90 90 Pitched Roof Flat Roof Products for PITCHED & FLAT ROOFS From Warm Roof Construction Pitched Roofs Min. 35mm Helical nails fix counterbattens
More informationmanthorpe Roll-Out Dry Fix Ridge System building products Fixing Instructions MBP 8265e
manthorpe building products Roll-Out Dry Fix Ridge System Fixing Instructions MBP 8265e Ridge Details Fig A. Assembly View of Dry Ridge Detail s/s screw clamping plate rubber washer foam spacer ridge tile
More informationBuilders Metalwork Product Selector 2018
Builders Metalwork Product Selector 2018 www.bpcfixings.com Manufacturing in the UK since 1977 Contents SMH Timber to Masonry Joist Hangers 4 Timber to Timber Joist Hangers 4 Angle Brackets 6 Restraint
More informationPryda Timber Connectors
Pryda Timber Connectors Pryda Lintel Guide Engineered Steel Wall Lintels March 2014 ESSENTIAL NOTES PRYDA PRODUCT GUIDES INTRODUCTION The information in this Product Guide is provided for use in Australia
More informationISSUE Erection Manual
Erection Manual The details and information in this book are for guidance of the erection of panels and flooring only. They are not site specific. Refer to the relevant panel drawings for the site, which
More informationAttach Trusses and Rafters Faster
Attach Trusses and Rafters Faster SDWC TRUSS Screw Truss-to-Plate Connections For Truss-to-Plate Connections The Strong-Drive SDWC TRUSS screw provides a truss- and rafter-to-top-plate connection. The
More information3.1 General Provisions
WOOD FRAME CONSTRUCTION MANUAL 107 3.1 General Provisions 3.1.1 Prescriptive Requirements The provisions of this Chapter establish a specific set of resistance requirements for buildings meeting the scope
More informationLVL8 H1.2 GENERAL FRAMING. Eco Friendly Revolutionary H1.2 Treatment Azotek by Zelam
LVL8 H1.2 GENERAL FRAMING Eco Friendly Revolutionary H1.2 Treatment Azotek by Zelam NPIL/MARCH2015 Introduction to NelsonPine LVL8 H1.2 NelsonPine LVL is an engineered wood composite made from rotary peeled
More information50948-RHN Putney. 06 January This document includes: Aluminium strip/ sheet coverings/ flashings 1. Code Section Revision Dated
50948-RHN Putney 06 January 2018 This document includes: Code Section Revision Dated H72 Aluminium strip/ sheet coverings/ flashings 1 Table of Contents Title H72 Aluminium strip/ sheet coverings/ flashings
More informationSTRUCTURAL BRACKETS CATALOGUE
08/2011 STRUCTURAL BRACKETS CATALOGUE SUPERIOR QUALITY, HOT DIP GALVANISED, HEAVY DUTY BRACKETS FOR FIXING TIMBER TO TIMBER, TIMBER TO CONCRETE, TIMBER TO STEEL The BOWMAC product range is designed to
More informationThe Influence of Nails and Plasterboard on the Racking Resistance of Stud Walls
Building 1 Grosvenor Court, Hipley Street OLD WOKING, SURREY GU22 9LL Tel: +44 (0) 1483 769518 Fax: +44 (0) 1483 770863 E-mail: design@silvatecdesigncom Internet: wwwsilvatecdesigncom The Influence of
More informationFlooring Nails 6-D Flooring Nails $3.40 / 1# 6-D Flooring Nails $14.50 / 5# 8-D Flooring Nails $3.40 / 1# 8-D Flooring Nails $14.
Nails Nails Drywall Screws Common Nails 4D Common Nails $3.85 / 1# 6D Common Nails $3.00 / 1# 6D Common Nails $74.25 / 50# 8D Common Nails $3.00 / 1# 8D Common Nails $74.25 / 50# 10D Common Nails $3.00
More informationRestraint Fittings. 2.4 Restraint Fittings. } Tiedown Single Stud Fitting. Tiedown Single Stud. Tiedown Single Stud allsafe
24 Restraint Fittings Different materials and surface qualities make them custom-fit } Tiedown Single Stud Fitting Tiedown Single Stud Tiedown single stud Ultimate load: see table, with heavy-duty track
More informationFASTENERS BUILDING DEPARTMENT
FASTENERS BUILDING DEPARTMENT 952-446-1660 WWW.CITYOFMINNETRISTA.COM This handout is intended only as a guide and is based in part on the 2015 Minnesota Residential Code, Minnetrista City ordinances, and
More information2.4 Restraint Fittings. Restraint Fittings
24 Restraint Fittings Restraint Fittings 44 Best in class allsafe JUNGFALK provides only high quality fittings Made in Germany Integrated buckle with fitting Standard single stud fitting Our in-house production
More informationDesigned for Building Designed for Living
Designed for Building Designed for iving decorative hardware Add Beauty and Strength to Your Custom Outdoor iving Structures ith Outdoor Accents, a new line of decorative timber connectors and fasteners
More informationREGENCY TIMBER BUILDINGS
REGENCY TIMBER BUILDINGS TEL 01948 830460 UNIT 22 PENLEY IND EST, PENLEY.WREXHAM. LL13 0LQ 1 Garage fitting instructions Tools needed handsaw, hammer, Stanley knife with hook blade, tape measure, battery
More informationWHY YOU SHOULD USE TUFFLOOR. components
Tuffloor DESIGN GUIDE WHY YOU SHOULD USE TUFFLOOR Strong and Easily Installed Tuffloor is a steel floor framing system designed for strength and ease of installation, and is an easy and economical alternative
More informationInstallation Guide GRP Dormer
Installation Guide GRP Dormer To ensure optimum performance please follow the correct fitting procedures outlined in this installation guide. Site safety and good building practice should be adhered to
More informationSecuAnch Roof Anchor System
Height Safety Products Email: marketing@fallprotec.com SecuAnch Roof Anchor System 1 Presentation The SecuAnch lifeline is designed to be permanently installed on buildings and other structures where maintenance
More informationVERSA-LAM. An Introduction to VERSA-LAM Products
44 VERSA-LAM An Introduction to VERSA-LAM Products VERSA-LAM is one of the strongest and stiffest engineered wood products approved in the UK. 241 302 356 406 VERSA-LAM products are excellent as floor
More informationUPPER FLOORS TIMBER AND CONCRETE
UPPER FLOORS TIMBER AND CONCRETE FUNCTIONS OF AN UPPER FLOOR Functions: Support imposed loads Not deflect under load Strength and stability Provide restraint for external walls Fire resistance (30 minutes)
More information1. Tile Roof Installation:!
1. Tile Roof Installation:! * Solar Roof Fan have a different base plate and ventilation opening size. This will require different measurements and allowances to those shown as pictures. Materials Needed:
More informationAPPENDIX 1 : Post and Beam Model
Good Practice Guide to Hut Building Prepared by Reforesting Scotland s Campaign for a Thousand Huts (5th Draft) APPENDIX 1 : Post and Beam Model Peter Caunt & Bernard Planterose June 2017 www.thousandhuts.org
More informationAdhesive Air Terminal Bases. Universal Surface Bases. Offset Parapet Air Terminal Bases. Section 3.2. Air Terminals & Air Terminal Bases
equipment catalog 3-5 Bases Adhesive Bases Used for mounting on membrane or built-up roofs. Mounted with adhesive or plastic roofing cement. The cast base has a mechanical conductor connector. BS-C-3/8ID-ADH-AT
More informationAcceptable Standards of Domestic Construction
Truss or Rafter Roof Batten Triple grip fastener (for roof trusses) Foil lined Insulation blanket Top plate Sprocket Brick tie Top plate strapping at 1200mm max. cts. Note: Holding down straps should be
More informationENGINEERED BUILDING PRODUCTS. I-Beam HANGERS. NEW Enhanced Capacity with YELLOW MiTek 40 x 3.75mm nails
ENGINEERED BUILDING PRODUCTS I-Beam HANGERS NEW Enhanced Capacity with YELLOW MiTek 40 x 3.75mm nails I - B e a m H a n g e r s - F a c e & T o p F i x e d FOR FACE AND TOP FIXING OF I-BEAMS TO BEAMS APPLICATION:
More informationV nyl Gazebo truct c it Assembly Instr ons
V nyl Gazebo Vi Assembly Instr ct tr t u ru ons ct c i ti Pre-assembly Instructions A C B #1 - Site properly prepared. 4" - 6" clean stone 9 linear blocks 2" x 8" x 16" C C A A B B #1a - 12" sauna tubes,
More informationTOPSPAN 22 / 40 LYSAGHT TOPSPAN 22 / 40. Steel roof and ceiling battens for non cyclonic applications
TOPSPAN 22 / 40 LYSAGHT TOPSPAN 22 / 40 Steel roof and ceiling battens for non cyclonic applications Our TOPSPAN 22 ceiling batten and TOPSPAN 40 roof battens are the economical alternative to timber battens.
More informationICC-ES Evaluation Report Reissued March 1, 2011 This report is subject to renewal in two years.
ICC-ES Evaluation Report www.icc-es.org (800) -6587 (56) 699-05 ESR-0 Reissued March, 0 This report is subject to renewal in two years. A Subsidiary of the International Code Council DIVISION: 06 00 00
More informationINSTALLATION INSTRUCTIONS for TB6.2,TB7.0, TB7.8 & TB8.4
the unique loft conversion & flooring system INSTALLATION INSTRUCTIONS for TB6.2,TB7.0, TB7.8 & TB8.4 Unit 6, Devizes Trade Centre, Hopton Park, Devizes, Wiltshire, SN10 2EH t 01380 739000 e info@telebeam.co.uk
More informationFreestanding Guardrail System. Operation & Maintenance Manual
Freestanding Guardrail System Operation & Maintenance Manual Specification Free Standing Edge Protection - System Specification General Description Our freestanding edge protection system is a cantilevered
More informationCABLE TRUNKING & ACCESSORIES
CABLE TRUNKING & ACCESSORIES STRAIGHT CABLE TRUNKING SELF TAPPING SCREW CONNECTOR H W MATERIAL & FINISHING 1 Galvanised Iron to BS2989 : 1982 & Original Finishing 2 Hot Roll Steel to JISG 3131 SPHC & HDG
More informationTHE ENGINEERED WOOD ASSOCIATION
D A T A F I L E APA Performance Rated Rim Boards A rim board is the wood component that fills the space between the sill plate and bottom plate of a wall or, in second floor construction, between the top
More informationPryda Timber Connectors Nailplates Guide
Pryda Timber Connectors September 2016 A complete guide to the design, specifications and installation of Pryda Nailplates Pryda TABLE OF CONTENTS GENERAL NOTES Useful Notes and Definitions for effective
More informationPosi-Joist Installation Guide. A guide for storage, handling and installation of the MiTek Posi-Joist floor system
Posi-Joist Installation Guide A guide for storage, handling and installation of the MiTek Posi-Joist floor system Posi-Joist Installation Details A B C D F E A Masonry Wall Connection Details Blockwork
More informationTimber Connectors & Post Anchors. Click to start
Timber Connectors & Post Anchors Click to start Pryda Pryda has been an integral part of the building industry in Australia for over 40 years, particularly in timber truss and frame solutions with the
More informationIRC 2012 Code Compliant Wood Framed Residential details. Miss Installed Connectors with code references and remedies, discussion.
IRC 2012 Code Compliant Wood Framed Residential details Miss Installed Connectors with code references and remedies, discussion. You can help avoid this, by being diligent with inspections. Notes to Attendees
More informationAttachment of Residential Deck Ledger to Side of Metal Plate Connected Wood Truss Floor Ladder. Installation Instructions Revised 9/2/2016
Attachment of Residential Deck Ledger to Side of Metal Plate Connected Wood Truss Floor Ladder Installation Instructions Revised 9/2/2016 SBCA has been the voice of the structural building components industry
More informationSpecifications - Common Nails Diamond point, Flat head, round smooth shank, Bright, HDG, EG or cement coated (resin or vinyl) finish
Specifications - Common Nails Diamond point, Flat head, round smooth shank, Bright, HDG, EG or cement coated (resin or vinyl) finish ASTM F 1667-05 Table 15 Type 1, Style 10 - Common Nails Size Length
More informationBoughton Road, Stoke Ferry, King s Lynn, Norfolk. PE33 9BF Tel: Fax:
Shop IRONMONGERY Size Unit Field Gate Set (12") 300 mm Field Gate Set (24") 600 mm Field Gate Catch and Peg Adjustable Gate Eye Hook on Square Plate 100 mm Throw Over Gate Loops Drop Bolt 18" (Galv) 450
More informationNails. Nailing is a strong and easy method of fastening timber.
Nails Nailing is a strong and easy method of fastening timber. Types of Nails Bullet Head Nail General purpose nail with a small head allowing head to be punched below timber surface and then filled. Suitable
More informationHOME STRENGTHENING GUIDE HOW TO ECONOMICALLY STRENGTHEN YOUR HOUSE AGAINST EARTHQUAKES AND HURRICANES
HOME STRENGTHENING GUIDE HOW TO ECONOMICALLY STRENGTHEN YOUR HOUSE AGAINST EARTHQUAKES AND HURRICANES Grenville W Phillips II BSc, BEng, MASc, MURP, CEng, FIStructE, FCIHT, MAPM, MCSCE, MBAPE Chartered
More informationSteeline X-SPAN purlins
Steeline X-SPAN purlins DESIGN MANUAL F y y L R5 t D 2 Origin x x x x y D L steeline.com.au y y E CONTENTS IMPORTANT NOTES... 1-1 DISCLAIMER... 1-1 INTRODUCTION... 1-2 HOW TO USE THE X-SPAN purlins DESIGN
More informationWood Roof Framing Common Design and Construction Defects Concurrent Session #5.3, Friday April 28, 2017, 9:45 AM-10:30 AM
Wood Roof Framing Common Design and Construction Defects Concurrent Session #5.3, Friday April 28, 2017, 9:45 AM-10:30 AM William J. Dery, PE Sr. Structural Engineer Outline 1. Wood Roof Framing 101 the
More informationSYW Industry Sdn. Bhd. Stud Anchor. Hexagon Nut / Flange Nut. U - Bolt (c/w 2 Nuts) Steel Band. 1 of 8
SYW Industry Sdn. Bhd. Stud Anchor Hexagon Nut / Flange Nut U - Bolt (c/w 2 Nuts) Steel Band 1 of 8 BT Anchor (MM size) Expansion Anchor 2 of 8 Set Anchor Sleeve Anchor with Flange Nut 3 of 8 BT Anchor
More informationHIP AND GABLE ROOF COMPONENTS
Page 18. VU20976 Roof Framing HIP AND GABLE ROOF COMPONENTS Plan view of the hip and gable roof that you are going to build. Again, don't be tempted just to look the names, put in a bit more effort to
More informationFitting instructions for (Read instructions fully, before installing the door)
t;t;i~iij~1~ti1i1f~~jhij~!~ti~~f~~t~il~t~11f;'~rj~*:i1;~i;~~g~1!~t4rf~?' ~~a~ Fitting instructions for (Read instructions fully, before installing the door) Horizontal tracked doors supplied with ' Retractable
More informationGRP Roof Cowls. Issue 3.1
GRP Roof Cowls Issue 3.1 Product overview FAIRHAVEN GRP Roof Cowls are suitable for a wide range of ventilation applications including: Commercial kitchens Warehouses Workshops & factories Large retail
More informationRennicks stiffening channels & fixing clip conformity to EN ; 2007
Rennicks stiffening channels & fixing clip conformity to EN 1899-1; 007 Introduction This document details the performance of the Rennicks stiffening channels and fixing clips to EN 1899-1; 007. Rennicks
More informationRIDGE-JOIST CONNECTION 12/12 maximum slope
R1 RIDGE-JOIST CONNECTION Beveled bearing stiffener each side (see detail R8) 2 3 8" min. end nailing distance, typical United Steel Products LSTA24 or Simpson Strong-Tie LSTA24 strap with 7-10d x 1 1
More informationWanco Electric & Machinery Pte Ltd. Cable Management Systems. Cable Trunking
Wanco Electric & Machinery Pte Ltd Cable Management Systems Cable Trunking About Wanco Wanco Electric and Machinery Pte Ltd is the leader in electrical construction materials. Through continued support
More informationisd dunaferr Product catalogue
isd dunaferr Product catalogue HOT-DIP GALVANIZED PRODUCTS The base material of hot-dip galvanizing is cold rolled wide coil. Metal coating is performed in course of continuous hot-dip galvanizing Sendzimir
More informationProduction Technology woodtec Fankhauser GmbH Timber Frame + swiss quality Construction Table The Modular System for Timber Frames
woodtec Fankhauser GmbH Production Technology For Timber Frame Timber Frame + swiss quality Construction Table The Modular System for Timber Frames 2 woodtec Fankhauser The modules are only mechanically
More informationtechnical bulletin Roofline Installation Details No.7 Fascia Installation Details Typical Eaves Details K16 Fascia & 9mm Vented Soffit
Roofline Installation Details This is intended to provide you with a brief overview of the popular products in Kestrel s Roofline range, where they can be used and the main criteria for installation. Typical
More informationtechnical bulletin Roofline Installation Details No.7 Fascia Installation Details Typical Eaves Details K16 Fascia & 9mm Vented Soffit
Roofline Installation Details This is intended to provide you with a brief overview of the popular products in Kestrel s Roofline range, where they can be used and the main criteria for installation. Typical
More informationSECTION R507 DECKS DECKING LEDGER BOARD BEAM. FOOTING BEAM SPAN CANTILEVER For SI: 1 inch = 25.4 mm FIGURE R507.2 DECK CONSTRUCTION
SECTION R507 DECKS R507.1 Application. The provisions of this section shall provide prescriptive requirements for the design and construction of all uncovered, wood-framed, single-span exterior decks.
More informationTECHNICAL MANUAL. TERADOWEL and ULTRADOWEL. Reliable Dowel System for Floor Joints
TECHNICAL MANUAL TERADOWEL and ULTRADOWEL Reliable Dowel System for Floor Joints Version: PEIKKO GROUP 11/2018 TERADOWEL and ULTRADOWEL Reliable Dowel System for Floor Joints Dowels manufactured from high
More informationENGINEERED BUILDING PRODUCTS. Boomerang CONNECTOR
ENGINEERED BUILDING PRODUCTS Boomerang CONNECTOR B o o m e r a n g C o n n e c t o r FOR FIXING JACK/CUT-OFF TRUSSES TO HIP/BOOMERANG TRUSSES APPLICATION: The Boomerang Connector has been developed to
More informationCutting, Grinding and Abrasive Accessories
High quality range of abrasive cutting discs, grinding discs and surface preparation accessories engineered for ultimate performance Universal Diamond Blades Cutting and Grinding Discs The essential construction
More informationLateral Support. Decks over 24 above grade require lateral support* *Exceptions to be discussed later
Lateral Support Decks over 24 above grade require lateral support* *Exceptions to be discussed later Decking Types of Decking: -2x4s & 2x6s -five quarter span rated decking boards -Wood plastic composite
More informationIMAGINATION SOLAR LTD. Installation Guide A1. Planning The Collector Installation
Page 1 of 6 IMAGINATION SOLAR LTD Installation Guide A1 Planning The Collector Installation Unit 4 Montpelier Central, Station Road Bristol BS6 5EE t: 0117 943 6668 f: 0117 942 8998 e: enquiries@imaginationsolar.com
More informationStrong, lightweight composite structural I -Beam.
Strong, lightweight composite structural I -Beam. This Installation Guide has been prepared as a source of information to provide general guidance to consultants and in no way replaces the services of
More informationProduced by the Construction Resource & Development Centre. Reprinted by the Construction Industry Council
Produced by the Construction Resource & Development Centre. Reprinted by the Construction Industry Council Over the past 15 years the frequency and intensity of hurricanes impacting Jamaica has increased
More informationDeck Evaluation Checklist
Date: Reported By: Project Name/Client: Year Deck was Built: I. Stairs A. Not Applicable B. Are there any visible signs of cracks, decay or over-notching? No Yes 1. If yes, where? C. Stairway width: (Hint:
More informationInstallation Guide. Please read before installing SIPs Kit. 1 Method Statement for the erection of a SIPS Industries Kit Materials...
30a Renewable Chase Bibra Lake WA 6163 Tel: (08) 9494 2211 Fax: (08) 9494 2202 Email: info@sipsindustries.com.au Web: www.sipsindustries.com.au Installation Guide Please read before installing SIPs Kit.
More informationSECTION MASONRY ANCHORAGE AND REINFORCEMENT. Display hidden notes to specifier. (Don't know how? Click Here)
PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 04080 MASONRY ANCHORAGE AND REINFORCEMENT Display hidden notes to specifier. (Don't know how? Click Here) A. Post installed masonry anchors. B. Miscellaneous
More informationPryda Timber Connectors
Pryda Timber Connectors A complete guide to the design, specification and installation of Pryda Bracing March 2014 ESSENTIAL NOTES PRYDA PRODUCT GUIDES INTRODUCTION The information in this Product Guide
More informationNails, Fasteners, Connectors, and Framing
Nails, Fasteners, Connectors, and Framing Nails To order Nail Sizes Nail length is often referred to as d or penny. For example a 10-D nail or a 10 Penny Nail. Use the following chart for nail length reference.
More informationJ; ('& ): J; )'& ): J; +'& ): J; +(+ ): J;,)& ): 9WXb[ i[j J;9JKI <_n_d] <P%' '& <_n_d] IP 7ii[cXbo 7Z`kijc[dj 9WbYkbWj_ed \ehckbwi
INdex ZERTIFIZIERT 4 INTERIOR DOOR SIMONSWERK TECTUS TE 210 3D for unrebated and rebated, flush-faced quality doors Hinge up to 40 kg Technical Data Load capacity Length (leaf/frame) Width (leaf/frame)
More informationRecommended Mounting Heights DOLPHIN
Recommended Mounting Heights DOLPHIN s accessible washrooms s Dimensions associated with comfortable and extended reach ranges (in mm) Person Access Reach Height Depth angle Comfortable Extended Comfortable
More informationMulti-layer Insulation Blanket for
Pitched roof insulation Fully certificated Thermally tested in accordance with EN12667 High thermal resistance of 2.71m²K/W Class 1 Surface spread of flame Ideal for New build & Refurbishment Effective
More informationProduct #: Product #:
STANLEY FATMAX Push-Lock Groove Joint Pliers Multi-purpose jaws designed to grasp flat and round objects. Push-Lock technology allows for quick and easy adjustment in 17 positions. Induction hardened jaws
More informationhyjoist Options Range Installation Guide
hyjoist Options Range Installation Guide For on-site, technical and product support, including assistance in sizing freecall 1800 808 131 hyjoist Guide for Installation hyjoist is a cost effective, lightweight
More informationCRIMPED WIRE WHEELS JET PREMIUM WIRE WHEELS JET premium wire wheels have set the standard in industry as the best performing bench wire wheel for metal applications Heavy wire fill and the best piano wire
More informationInstallation Instructions
TEL: 09 579-8895 FAX: 09 579-2933 EMAIL: sales@nzfiredoors.co.nz NZ Fire Doors Ltd, 89 Gavin Street, Ellerslie, PO Box 12709, Penrose 1642, Auckland, New Zealand. www.nzfiredoors.co.nz Installation Instructions
More informationDOLPHIN TITAN CHANGING UNIT. Carrying capacity of more than 400kg
967 269 Plan 798 Elevation 100 626 Section BC101ES DOLPHIN TITAN CHANGING UNIT Carrying capacity of more than 400kg An alternative design embodying strength, safety and hygiene in a robust construction
More informationIntex Engineered Pergola System Installation Instructions. NOTE: See Appendix for Foundation Requirements
Intex Engineered Pergola System Installation Instructions NOTE: See Appendix for Foundation Requirements Pergola Installation, Freestanding (If pergola will be attached-to-structure, skip to page 3) 1.
More informationExtrusions POLYLOCK ATTACHING EXTRUSIONS
Extrusions POLYLOCK ATTACHING EXTRUSIONS ITEM # DESCRIPTION USES 1001 Aluminum Girt 16 lengths Used in metal end packages and sidewalls as horizontal members. Requires girt/baseboard splice (#1000). 1000
More informationMulti-layer Insulation Blanket for Roofs
Multilayer Insulation Blanket for Roofs Thermal Insulation in a 40mm thin, flexible, multilayer membrane Meets requirements of L1A, L1B 2010 In accordance with BR443 NHBC Acceptance Pitched roof insulation
More informationA Reference Guide. Continuous Hinge, Inventory and Service Worldwide Est End Play Design Engineering with Standard Continuous Hinges
Hinge Width Paint Clearance Knuckle Length End Play Design Engineering with Standard Continuous Hinges A Reference Guide Knuckle Dear Design Engineer or Purchasing Agent, We frequently see blueprints for
More informationHow To Build Decorative. Timber Awnings
How To Build Decorative Timber Awnings How to build a timber awning FOREWORD Timber awnings are a visually pleasing form of window shading. Properly built timber awnings can add value to your property
More informationCabonyx Installation Manual
Cabonyx Installation Manual Content Deck-Nyx and Plan-Nyx Installation Page 1 Flooring Products Page 1 Accessories Page 1 Installation Tools Page 2 Preparing Sub-structure Page 2 Installation Page 4 Cautions
More informationFASTENERS C O M P AT I B L E W I T H F E R O T I E S Y S T E M S. Which FERO Tie Systems Require Fasteners?
FASTENERS C O M P AT I B L E W I T H F E R O T I E S Y S T E M S Which FERO Tie Systems Require Fasteners? Structural Actions: Fastener,, or Both? With the exception of FERO tie systems that are directly
More informationRoll-Fix Kit The complete dry hip kit RFIG
H I P Roll-Fix Kit The complete dry hip kit RFIG.045-0906-1 Roll-Fix is a quick and simple dry-fix roofing kit for hips. l Quick and easy to install no special tools required l Universal application fits
More informationINSTALLATION AN EXPLODED VIEW OF A TYPICAL BRETT MARTIN RAINWATER INSTALLATION RAINWATER PRODUCT GUIDE
AN EXPLODED VIEW OF A TYPICAL BRETT MARTIN RAINWATER HANDLING Brett Martin Rainwater systems are light in weight and are therefore easy to handle. As with all other quality materials, Rainwater components
More informationMetroll. Purlins & Girts. C Section Purlins. C Section Purlins are manufactured from Galvaspan steel and are roll formed into C Section.
C Section Purlins C Section Purlins are manufactured from Galvaspan steel and are roll formed into C Section. Metroll C Section Purlins are recommended for simple, non-continuous span construction. Structural
More informationROYAL ULTRA-PRECISION ER COLLETS " TIR
ROYAL C EXPANDING COLLETS q Unlike chucks and most collets that grip the OD of a workpiece, C expanding collets are designed to grip on the ID of a part. q Accu-length design ensures precise workpiece
More informationSwifts cable ladder ancillary items
straight and curved dividers Straight dividers are used, along with curved dividers, to physically separate different types or groups of cable within one cable ladder run Straight dividers are supplied
More information