Extrusions POLYLOCK ATTACHING EXTRUSIONS

Size: px

Start display at page:

Download "Extrusions POLYLOCK ATTACHING EXTRUSIONS"

Norah Newton
6 years ago
Views:

Extrusions POLYLOCK ATTACHING EXTRUSIONS ITEM # DESCRIPTION USES 1001 Aluminum Girt 16 lengths Used in metal end packages and sidewalls as horizontal

1000 Girt/Baseboard Splice- 5/8 H x 1 W x 6 L Splices lengths of aluminum girt (#1001) and Polylock baseboard (#1090).

Structures. Attach to bow member using 1-1/2 pipe straps with two 5/16 x3/4 carriage bolts (#1338) and nuts (#1346).

When using double layered polyethylene on the roof, use the mark III insert (#1044). Requires two runs of Mark III inserts/gutter.

Also used on sidewall corner of poly sidewall houses. Requires one run of Mark III inserts (#1044).

1094 Double Polylock Eave 12 Lengths Used as an eave member on Rainbow Plus greenhouses with poly roof and sidewalls.

1 Extrusions POLYLOCK ATTACHING EXTRUSIONS ITEM # DESCRIPTION USES 1001 Aluminum Girt 16 lengths Used in metal end packages and sidewalls as horizontal members. Requires girt/baseboard splice (#1000) Girt/Baseboard Splice- 5/8 H x 1 W x 6 L Splices lengths of aluminum girt (#1001) and Polylock baseboard (#1090). Requires 4 tec screws (#1231)/splice Aluminum Polylock Gutter-16 lengths Rainbow Plus Gutter Splice 11-3/4" Used with Rainbow Plus Structures. Attach to bow member using 1-1/2 pipe straps with two 5/16 x3/4 carriage bolts (#1338) and nuts (#1346). One foot overhang (minimum) recommended at each end of the structure. Five foot overhang recommended when used with a rigid vent. When using double layered polyethylene on the roof, use the mark III insert (#1044). Requires two runs of Mark III inserts/gutter. Splice gutter with 5/16 x ¾ carriage bolts (#1338) and nuts (#1346). Drilling of holes to mount splice or gutter is not needed. Requires 12 bolts and nuts/splice Polylock Edge-16 lengths Attached to roof bars under the bent and keeps bent headers operable when the greenhouse roof is double air layered. Also used on sidewall corner of poly sidewall houses. Requires one run of Mark III inserts (#1044) Angle Splice Plate 6 Attaches vent header (#1003) at corners on poly sidewall houses. Attach to eave and baseboard with four tec screws (#1231) Double Polylock Eave 12 Lengths Used as an eave member on Rainbow Plus greenhouses with poly roof and sidewalls. Attaches to L connector bar using two 5/16" x 1" hex head bolts (#1340) with locknuts (#1346). NOTE: Use on PowerHouse greenhouses requires an Eave Spacer (#1007) located between the bow and the double Polylock eave extrusion using two 5/16" x 1-3/4" hex head bolts (#13421) with locknuts (#1346). Requires two runs of Mark III Inserts (#1044) Eave Spacer 4-1/2 Used with used Polylock panel edge (#1092) and double eave (#1094) on Powerhouse models. Located between the bow and the eave extrusion using two 5/16 x 1-3/4 hex head bolts (#13421) with locknuts (#1346).

21081 Gable End with Pocket Pre-punched 12'3" Secures poly roof. Attach to end bow every two feet using 1.90 pipe straps (#15312) or 2.

Requires 21083 Double Polylock End or Double Splice Pre- Punched 12 lengths 10991 Corner Spacer for Double Eave 3-3/8 one run of Mark III inserts (#1044).

Pre-punched holes at 24 on center for attachment with pipe straps (holes punched for both 1.90 and 2.40 ). Requires two runs of Mark III inserts (#1044). Finishes eave member (#1094) at corner.

Two per run of double eaves needed. 1092 Polylock Panel Eave 12 Eave member on a house with poly roof and rigid cover sides.

NOTE: Use on Powerhouse greenhouses requires an eave spacer (#1007) located between the bow and the poly eave extrusion using two 5/16 x 1-3/4 hex head bolts (#13421) with locknuts (#1346).

Attach to L connector using one 5/16 x 1 hex head bolts (#1340) and locknuts (#1346). On Powerhouse models use an eave spacer (#1007) and one 5-16 x 1-1/2 hex head bolt (#1342) and locknut (#1346).

houses; also used at eave for houses with poly roof and sidewalls. Attaches over existing roof rafters, requires two runs of Mark III inserts (#1044). NOTE: Not for 1.90 or 2.

2 21081 Gable End with Pocket Pre-punched 12'3" Secures poly roof. Attach to end bow every two feet using 1.90 pipe straps (#15312) or 2.40 pipe straps (#1533) and two 5/16 x 3/4 hex head bolts (#1330) with locknuts (#1346). The lower leg is cut to aid in bending. Requires Double Polylock End or Double Splice Pre- Punched 12 lengths Corner Spacer for Double Eave 3-3/8 one run of Mark III inserts (#1044). Attaches double poly to the roof and endwalls. Also used as a splice between two lengths of double poly roofing. Pre-punched holes at 24 on center for attachment with pipe straps (holes punched for both 1.90 and 2.40 ). Requires two runs of Mark III inserts (#1044). Finishes eave member (#1094) at corner. Attach to L connector using one 5-16 x 1 hex head bolt (#1340) and nut (#1346). On Powerhouse models use an eave spacer (#1007) and one 5-16 x 1-1/2 hex head bolt (#1342) and locknut (#1346). Two per run of double eaves needed Polylock Panel Eave 12 Eave member on a house with poly roof and rigid cover sides. Attach to L connector bar using two 5/16 x 1 hex head bolts (#1340) and locknuts (#1346). NOTE: Use on Powerhouse greenhouses requires an eave spacer (#1007) located between the bow and the poly eave extrusion using two 5/16 x 1-3/4 hex head bolts (#13421) with locknuts (#1346). Requires one run of Mark III inserts (#1044) Corner Spacer for Polylock Panel Edge 3-3/ Double Polylock Ridge Cap 16 Finishes eave member at corner. Attach to L connector using one 5/16 x 1 hex head bolts (#1340) and locknuts (#1346). On Powerhouse models use an eave spacer (#1007) and one 5-16 x 1-1/2 hex head bolt (#1342) and locknut (#1346). Two per run of panel edge (#1092) needed Designed as a ridge plate for covering A-Frame greenhouses with double layers of poly; splice plate for connecting two lengths of poly roof covering over long houses; also used at eave for houses with poly roof and sidewalls. Attaches over existing roof rafters, requires two runs of Mark III inserts (#1044). NOTE: Not for 1.90 or 2.40 bow applications-see #21083 for those applications Gutter Slide Polylock 12 Used on gutter for securing poly roof. Requires one run of Mark III inserts (#1044) Poly/Fiber Splice 12 Splice plate for the end of a fiberglass roof and the beginning of a poly roof. Attaches every two feet over the bow using appropriate pipe strap with two 5/16 x 3/4 hex head bolts (#1338) and locknuts (#1346). Requires one run of Mark III inserts (#1044) Polylock Base Rail 12 Attaches poly film to eaves, gutters, sides and ends. Requires seven each of 1/4 hex head bolts and seven locknuts (#1303) per 12 section. Requires one run of Mark III inserts (#1044). NOTE: Screws not recommended 1090 Polylock Baseboard 12 Baseboard for attaching roof or sidewall poly on ground to ground or raised sidewall greenhouses. Attach at every column with a pipe strap and two 5/16 x 3/4 carriage bolts (#1339) with nuts (#1346). For splicing use girt/baseboard splice (#1000) and four tec screws (#1231) per splice. Requires one run of Mark III inserts (#1044).

102902 Walkover Polylock 12 Requires bar cap (#1030). Requires one run of Mark III inserts (#1044).

Requires one run of Mark III insert (#1044).

One linear foot is needed for every linear foot of base section.

(Full roll is 1,750 ). NOTE: Used for double poly.

(Full roll is 1,500 ). NOTE: Used for single poly.

10088 Mark IV Polylock-with-a- Twist wire 4 10081 Polylock-with-a-Twist Base 16 lengths Sized to fit

Similar to #10082 Polylock-with-a- Twist wire except for the reduced size and comes with red vinyl tips.

10085 Polylock-with-a-Twist Dogleg Base 16 Requires splice (#10086) with tec screws (#10342), four each

Polylock-with-a-Twist Gutter Eave 12 Used on end bows to secure poly for roof and endwall.

Four runs of Polylock-with-a-Twist wire are recommended (#10082). Used on end bows to secure poly.

Used as the top of a System 2000 interior partition.

3 Walkover Polylock 12 Requires bar cap (#1030). Requires one run of Mark III inserts (#1044) Wing End with Poly 12 Leading edge stop on a mid wing system. Requires one run of Mark III insert (#1044) Mark III Insert 4 Comes with vinyl insert, fits all Polylock extrusions. One linear foot is needed for every linear foot of base section Beige Vinyl Standard replacement beige vinyl for Mark III inserts, sold by the linear foot. (Full roll is 1,750 ). NOTE: Used for double poly Black Vinyl Replacement black vinyl for Mark III inserts. Sold by linear foot. (Full roll is 1,500 ). NOTE: Used for single poly Polylock Installation Tool Used to install and remover Mark III inserts. Two required Mark IV Polylock-with-a- Twist wire Polylock-with-a-Twist Base 16 lengths Sized to fit all existing Polylock extrusions: replacement wire for Mark III inserts. Similar to #10082 Polylock-with-a- Twist wire except for the reduced size and comes with red vinyl tips. Install using 1/4 x 2-1/2 truss head bolt (#1294) and the drill guide location at every two feet Polylock-with-a-Twist Dogleg Base 16 Requires splice (#10086) with tec screws (#10342), four each Polylock-with-a-Twist Double Polylock-with-a-Twist Gable End Polylock-with-a-Twist Gutter Eave 12 Used on end bows to secure poly for roof and endwall. Also used to splice a roof in the middle of the greenhouse. Four runs of Polylock-with-a-Twist wire are recommended (#10082). Used on end bows to secure poly. This extrusion is notched to fit the bow s arch. Double run of wire (#10082) recommended. Used as the top of a System 2000 interior partition. Requires wire (#10082) Polylock-with-a-Twist with Mounting Rail Polylock-with-a-Twist with Fiber Splice Polylock-with-a-Twist with Carriage Bolt Mount Polylock-with-a-Twist wire 6 Ideal for insect screens, curtains, and partitions. Requires wire (#10082) For transitioning from poly to rigid covering on sides or ends. Requires wire (#10082) Designed for Rainbow Super gutter. Use with 5/16 x 3/4 carriage bolt (#1338) and locknut (#1346). Stainless steel wire, used with Polylock-with-a-Twist bases, comes in 6 lengths and has black vinyl tips

RIGID COVERING EXTRUSIONS ITEM # DESCRIPTION USES 10411 15 Ridge Extrusion 12

Extrusion 6'3-1/4" Plus application only 996006 26.5 8mm Ridge 12 996008 26.

5 8mm Ridge 75-1/4 Attaches to ridge purlin to accept panels at ridge; for CS3

5 8mm Ridge 63-1/4 P2651 Aluminum Flash Angle For houses with widths divisible by

3 x 6 x 12 1022 Corner Molding 9 Corner molding with PCSS sidewalls.

Used with System 2000 and Rainbow Plus 10222 Corner Molding 13 greenhouses.

Used as an eave on greenhouses with fiberglass or PCSS roof and sidewalls.

0674 Corner/Roof Cap 9 Used at corners of sidewalls and endwalls to cap the edge

06741 Corner/Roof Cap 11 06742 Corner/Roof Cap 13 06751 Gable End Cap Notched 12

Used on end roof and attaches top of endwall panels.

Connects rigid panels on endwalls to roof panels.

10992 Corner Space for Rigid Panel Eave 3-3/8 Finishes eave member at corner.

P2627 Corrugated Polycarbonate/Fiberglass Gable End Cap 10 System 2000

4 RIGID COVERING EXTRUSIONS ITEM # DESCRIPTION USES Ridge Extrusion 12 Attaches to ridge purlin to accept panels at ridge; Rainbow Ridge Extrusion 6'3-1/4" Plus application only mm Ridge mm Ridge mm Ridge 75-1/4 Attaches to ridge purlin to accept panels at ridge; for CS mm Ridge 63-1/4 P2651 Aluminum Flash Angle For houses with widths divisible by six feet on corners, interior gutter partition corners. 3 x 6 x Corner Molding 9 Corner molding with PCSS sidewalls. Attach with tec screws Corner Molding 11 (#10342). Used with System 2000 and Rainbow Plus Corner Molding 13 greenhouses. NOTE: 3.5 x3.5 x length 1093 Rigid Panel Eave 12 Rainbow Plus only. Used as an eave on greenhouses with fiberglass or PCSS roof and sidewalls. Attach to L connector using two 5/16 x 1 hex head bolt (#1340) with locknuts (#1346). NOTE: Rubber is required. Fiberglass eave does not work on Powerhouse models Corner/Roof Cap 9 Used at corners of sidewalls and endwalls to cap the edge of corrugated panels Corner/Roof Cap Corner/Roof Cap Gable End Cap Notched Rigid Panel Gable, Notched 12 For System 2000 and Rainbow Plus structures. Used on end roof and attaches top of endwall panels. Secure with #12 x 1 tec screws (#10342). Connects rigid panels on endwalls to roof panels. Functional for either A frame or Rainbow style houses Corner Space for Rigid Panel Eave 3-3/8 Finishes eave member at corner. Attach to L connector using one 5/16 x1 hex head bolt (#1340) and locknut (#1346). P2627 Corrugated Polycarbonate/Fiberglass Gable End Cap 10 System 2000 application. Caps the edge of the corrugated roof panel PCSS Double Splice PCSS Double Splice 11 Connects 8mm panels on sides and endwalls PCSS Double Splice Single Cap Single Cap 11 Seals side of 8mm panels on endwalls and sidewalls Single Cap mm Panel End Cap 16 Rainbow Plus application. Seals PCSS panels at eave and gutter. Requires 5/16 x 3/4 carriage bolt (#1338) and locknut (#1346) mm Panel End Cap 16 System 2000 application. Seals PCSS panels at eave and gutter. Requires 5/16 x 3/4 carriage bolt (#1338) and locknut (#1346).

0675 Un-notched Classic Gable System 2000

Used on end roof and attaches End Cap 12 top

locknut (#1346) and one selfdrilling tec screw

1029 PCSS Glazing Bar 18 Secures panels to

Requires PCSS Glazing Bar Cap (#1030) and 1

Cap 18 Secures PCSS panels to roof using

Glazing Bar (#1030) or walkover (#102902) over

Attach with four each of 5/16 x 1/2 hex head

foot. 10374 PCSS Gable Bar Cap 18 Used on

Attach to PCSS glazing bar (#1029) using 1

10321 PCSS Gutter Spacer 3/8 x 4-1/2 Puts

Requires two 5/16 x1 hex head bolt (#1340) and

P4216 Interior Partition Top Extrusion Glaze

Attach with 1/4 x 3/4 bolt (#1278) and locknut

sidewall with rigid panels. Attached to gutter.

5 0675 Un-notched Classic Gable System 2000 Application. Used on end roof and attaches End Cap 12 top of endwall panels. Secure with #12 tec screw (#10342) mm Vent Ridge 16 For ridge and existing vent headers. Requires 5/16 x 3/4 carriage bolt (#1338) and locknut (#1346) and one selfdrilling tec screw with washer (#1233) PCSS Glazing Bar 18 Secures panels to existing roof members. Requires PCSS Glazing Bar Cap (#1030) and 1 self drilling tec screw with washer (#1233) PCSS Glazing Bar Cap 18 Secures PCSS panels to roof using glazing bar (#1029) and 3/4 self drilling tec screws (#1231) PCSS Glazing Bar Splice 6 Splices Glazing Bar (#1030) or walkover (#102902) over roof of Quonset or A-frame structures. Attach with four each of 5/16 x 1/2 hex head bolt (#13382) and locknut (#1346) per linear foot PCSS Gable Bar Cap 18 Used on A-frame gable end roof bars. Attach to PCSS glazing bar (#1029) using 1 self drilling tec screws with washer (#1231) PCSS Gutter Spacer 3/8 x 4-1/2 Puts glazing bar in line with end seal. Requires two 5/16 x1 hex head bolt (#1340) and locknut (#1346). P4216 Interior Partition Top Extrusion Glaze System 2000 application only. Attach with 1/4 x 3/4 bolt (#1278) and locknut (#1303) two foot on center. P21073 Outside Eave 12 System 2000 applications with no gutter. Rigid covering only Outside Gutter Eave 12 System 2000 application only. Used on top of sidewall with rigid panels. Attached to gutter Rigid Cover Gutter Adapter 8 P21074 Outside Eave Spacer 2-1/4 Rainbow Plus application only. Fits into Polylock extruded gutter or eave when fiberglass roof is desired. Two runs per run of gutter. May also be used with any Polylock base. System 2000 no gutter application. End extrusion that wing closes on to seal roof. P2544 P2389 3x2 Corner Girt Mounting Bracket 3x2 Sidewall Girt Support Bracket System 2000 application only. System 2000 application only.

E-Z GROW HOBBY GREENHOUSE. I n s t r u c t i o n M a n u a l & D i s c l a i m e r s

E-Z GROW HOBBY GREENHOUSE. I n s t r u c t i o n M a n u a l & D i s c l a i m e r s E-Z GROW HOBBY GREENHOUSE I n s t r u c t i o n M a n u a l & D i s c l a i m e r s Contractors/Installers Note: This manual is the property of the customer. Please leave it in the possession of the customer.