FLAT ROOF CARPORT RECOMMENDED INSTRUCTION MANUAL
|
|
- Esther Anthony
- 5 years ago
- Views:
Transcription
1 FLAT ROOF CARPORT RECOMMENDED INSTRUCTION MANUAL
2 Table of Contents Introduction... 2 Components... 3 Step 1 Marking out the Perimeter of the Carport... 3 Step 2a Footing Set-Out for Concrete Block Pad Footing... 3 Step 2b Footing Set-Out for Concrete Slab... 4 Step 3 Preparation of Carport Posts... 5 Step 4 Post Sleeve on Base Plate Set-out... 6 Step 5 Preparation of Edge Beams... 7 Step 6 Assemble and Stand the Carport Post and the Edge Beam... 8 Step 7 Fit the Cross Beam (Rafters)... 8 Step 8 Fit the remaining Cross Beams... 9 Step 9 Plumb the Posts... 9 Step 10 Fix Base Plate Permanently... 9 Step 11 Carport Frame to be Square... 9 Step 12 Complete Fixing of the Frame Step 13 Triangular Haunch Knee Brace Step 14 Fit Roof Sheeting Step 15 Fit Gutters and Flashings Step 16 Cut and fit downpipes Step 17 Finish
3 Introduction This Recommended Instruction Manual is a guide only. IT IS IMPERATIVE TO REFER TO THE ENGINEERING PLANS SUPPLIED WITH THIS MANUAL FOR SPECIFICATIONS AND DETAILS TO ALL THE CHAPTERS IN THIS MANUAL. Due to the large range of sizes and styles available, it is not possible to prepare an instruction manual for all styles, sizes and models. The following instruction manual is an EXAMPLE of a 6m wide x 6m long Flat Roof Carport. The maximum size of Flat Roof Carport by Multiport program is 12m span x 8m long x 4.2m high. Any Flat Roof Carport size greater than these dimensions has to be sent for Custom Engineering. Things to do before you commence construction a. It is recommended to obtain professional advice to ensure your needs are adequately met. b. Check with your local government of any approval or restriction requirements. It is your responsibility to ensure that all approvals required are obtained. Safety Advice Important DISCLAIMER: This is a general safety advice. Refer to relevant state workplace authority website for safety advice on specific items and OH&S safety requirements. NOTE: Do not rely on this guide as exhaustive of all hazards that may exist on a construction site. Construction hazards must be assessed for risk and controls put in place to reduce the risk identified before commencing work. CHECK AND ENSURE THAT YOUR COMPONENTS ON SITE ARE CORRECT AND COMPLETE AS PER THE BILL OF MATERIALS. IF IN DOUBT, PLEASE CONTACT YOUR SUPPLIER. 2
4 Components Step 1 Marking out the Perimeter of the Carport Mark and set-out the perimeter of the Carport with pegs and strings. In this example, the size of the carport is 6.0m wide x 6.0m long. Refer to Engineering Plans for the actual size and specifications of your specific job. Step 2a Footing Set-Out for Concrete Block Pad Footing Mark and set-out the location of concrete pad footings to be excavated. The centre line of the posts is equivalent to the centre line of the pad footings. Using the string set-out of the perimeter as a guide, edge of the post is set in on the sidewall by the flange width of the edge beam. To determine the centreline of the post, add 1/2 of the post size to the width of the edge beam. Example: C150 Edge Beam has a 64mm flange width so the edge of the post is set in by 64mm from the string set-out. The post size is 75mm x 75mm so half of 75mm is 37.5mm. The centreline of the post is 64mm set in from the string set-out. The posts are set in on the endwall by 1300mm to centre line of posts as shown in Diagram Ab. Ensure that the diagonal measurements of the pad footings are equal, level and square. Refer to the Engineering Plans for size and specifications of the concrete pad footing. Dig out and pour concrete pad footings. 3
5 Step 2b Footing Set-Out for Concrete Slab Mark and set-out the edges of the concrete slab to be excavated. The edge of the slab is equivalent to the string set-out of the perimeter as a guide, edge of the post is set in on the sidewall by the flange width of the edge beam. To determine the centreline of the post, add 1/2 of the post size to the width of the edge beam. Example: C150 edge beam has a 64mm flange width so the edge of the post is set in by 64mm from the string set-out. The post size is 75mm x 75mm so half of 75mm is 37.5mm. The centreline of the post is 64mm in from the concrete slab set-out. The posts are in on the endwall by 1300mm to centre line of posts as shown in Diagram As. Ensure that the diagonal measurements of the concrete slab are equal, level and square. Refer to the Engineering Plans for size and specifications of the concrete slab. TIP: Pegs and strings marking the perimeter of the building to be left in place until the position of base plates are clearly marked. 4
6 Step 3 Preparation of Carport Posts Check levels of footings and if required, cut posts accordingly to suit the building height requirements as the posts are supplied in stock lengths. Set-out and bore two holes at the top of the carport posts to match the punching (holes) detail of the C-Purlin edge beams. Refer to the Engineering Plans for the holes specifications. Size of holes and punching details vary according to the size of the C-Purlin edge beam. A table below is provided for the C-Purlin punching details for reference. The edge beam is to be bolted to the top of the post. Refer to the Engineering Plans for bolt size and specifications. 5
7 Set-out and bore two holes at the bottom of the carport post, punching details to be the same as the top of the post. Holes at bottom of post are only required if posts are to be bolted to the post sleeve on base plate fixed to concrete footing or slab. Refer to Diagram B. TIP: If Post is to be embedded, angle bracket at the base of the post with 2 tek screws is to be fixed in lieu of the bolt holes. Refer to Diagram C. You may stand the plumb post into the excavated holes and pour concrete at this stage or go to Step 5 to bolt the eave purlin to the posts before standing the posts. Step 4 Post Sleeve on Base Plate Set-out Using the set-out string marking the perimeter of the building as a guide, mark the position of the post sleeve on base plate. The post sleeve which is inserted to the bottom of the post is in on the sidewall by the flange width of the edge beam plus 1/2 of the post size and is in on the endwall by 1300mm from edge to centre line as shown in Diagram D. Fix the post sleeve on base plate to the concrete footing with fastening type as per the Engineering Plans. TIP: The centre line of post is equivalent to the centre line of post sleeve on base plate. NOTE: The post sleeve on base plate comes in 2-hole or 4-hole depending on the size and the requirements of the carport. Refer to the Engineering Plans for the specifications of the post sleeve. 6
8 Step 5 Preparation of Edge Beams On the outer web side of the edge beams which is the two longest C-Purlins, set-out and attach the shorter leg of the general purpose angle bracket (GPB) with 2 frame bolts. This bracket will be fitted inside the cross beam (rafter). Refer to Detail E. NOTE: Depending on the size of the carport it may be necessary to fit triangular carport knee braces between the edge beam and the post. Refer to Step 13 for detailed instructions of the knee brace. 7
9 Step 6 Assemble and Stand the Carport Post and the Edge Beam Bolt the edge beam to the carport posts temporarily with the framing bolts supplied, one per column. Stand post in footing holes if embedded or insert the post over the post sleeve with base plate. Refer to the Engineering Plans for specific footing requirements. Plumb the post and hold in place with 2 frame screws through the edge beam into the post. Adjust and plumb the post as required. The bolts for this side frame can now be completed and permanently tightened. Repeat this process to erect the other edge beam. Step 7 Fit the Cross Beam (Rafters) Place the cross beam in position on the side of the front posts and bolt temporarily into each post. Repeat this step at the rear pair of posts. 8
10 Step 8 Fit the remaining Cross Beams Fit and bolt the general purpose bracket to the inner web face of the remaining cross beams. The cross beams at the gutter and the high end has the open side of the C-Purlin cross beams face out. Refer to Step 12 3D View. Step 9 Plumb the Posts Plumb the front posts on one side and temporarily brace it into position. Drill the remaining top hole and fit the second bolt. Plumb the rear post on the same side and fit the remaining bolt through the edge beam. Step 10 Fix Base Plate Permanently Drill and fit masonry fixings to the base plates with post sleeve for posts that have been plumbed if base plate is selected OR set concrete into the footing hole if embedment is selected. Step 11 Carport Frame to be Square Ensure the diagonals shown dotted are equal (as shown in the diagram) and prop the side that is not fixed into position. 9
11 TIP: Another option to use to check that the diagonals are equal is to calculate using this formula. Diagonal = square root (length 2 + width 2 ). Step 12 Complete Fixing of the Frame On the side that is on props, fix the remaining two posts to the edge beams. Plumb the posts then either bolt to the post sleeve with base plate or concrete them into position whichever is selected. Ensure the cross beams are level. Fit and permanently fix the long bolts supplied through to the post sleeve inside the base of the posts. TIP: If posts are embedded into concrete footings, it is recommended to wait for a few hours until the concrete is set before starting on the roofing sheets. 10
12 Step 13 Triangular Haunch Knee Brace If knee braces are required and have been supplied (check Bill of Materials), these are to be fitted in 2 different directions namely; between the posts and the cross beams (4 off) and between the inner side of the posts and the edge beams (4 off). NOTE: Centre posts on longer carports have the knee brace fitted between the edge beam and the post on left and right of the post. If fitted at this stage, the corner of the knee brace will need to be notched 20mm both sides to allow for easy fitting. 11
13 Step 14 Fit Roof Sheeting Lay the first sheet in position and ensure that the roof sheet is flush with the outside face of the first rafter (cross beam) on the high end. This edge of the rafter (cross beam) should be pan fixed using wall screws to aid in the fitting of barge capping. If the frame is square, the first sheet should now be flushed along the length of the edge beam. All other sheets may now be fixed at crest with the number of screws per sheet at supports specified on the Engineering Plans. Ensure that roofing sheets are turned up at the high end to prevent water running off this end. 12
14 Step 15 Fit Gutters and Flashings Remove plastic cover protecting gutters and flashings before they are fitted. a) Fit the cover flashing to the gutter end of the roof b) Fit the stop ends and nozzle to the guttering c) Fit gutter brackets to the cover flashing with pop rivets. Ensure the brackets are fitted with a string line to the required fall location. d) Fit the gutter brackets into the gutter e) Fit side and head barge flashing and ensure that the bottom edge of the flashing is fixed to the bottom lip of the C-Purlin with pop rivets. Step 16 Cut and fit downpipes Cut and fit the downpipes to the drainage system. Step 17 Finish Remove any temporary bracing and check that all the required bolts and tek screws are fitted and tightened. BRUSH COMPLETE CARPORT DOWN WITH A SOFT BROOM TO REMOVE ANY METAL DUST/FILINGS CAUSED BY ANGLE GRINDER. CONGRATULATIONS ON A JOB WELL DONE! 13
GABLE ROOF CARPORT RECOMMENDED INSTRUCTION MANUAL
GABLE ROOF CARPORT RECOMMENDED INSTRUCTION MANUAL Table of Contents Introduction 2 Components 3 Step 1a Marking out the Perimeter of the Carport with Footing only 3 Step 2a Footing Set-Out for Concrete
More informationDUTCH GABLE CARPORT RECOMMENDED INSTRUCTION MANUAL
DUTCH GABLE CARPORT RECOMMENDED INSTRUCTION MANUAL Table of Contents Introduction 2 Components 3 Step 1a Marking out the Perimeter of the Carport with Footing only 4 Step 2a Footing Set-Out for Concrete
More informationDUTCH GABLE FREESTANDING CARPORT
DUTCH GABLE FREESTANDING CARPORT STRATCO OUTBACK ASSEMBLY INSTRUCTIONS. Your complete guide to building a FREESTANDING Outback DUTCH GABLE CARPORT BEFORE YOU START Carefully read these instructions. If
More informationTRADITIONAL GABLE ATTACHED PATIO AND CARPORT. Your complete guide to building an ATTACHED Outback TRADITIONAL GABLE PATIO or CARPORT
TRADITIONAL GABLE ATTACHED PATIO AND CARPORT STRATCO OUTBACK ASSEMBLY INSTRUCTIONS. Your complete guide to building an ATTACHED Outback TRADITIONAL GABLE PATIO or CARPORT BEFORE YOU START Carefully read
More informationSTEEL BUILDINGS RECOMMENDED INSTALLATION GUIDE
STEEL BUILDINGS RECOMMENDED INSTALLATION GUIDE 3 TO 30 METRE SPAN FRAME FIRST METHOD SUPPLIED BY: Last update 2 May 2008 2008 FBHS (Aust) Pty Limited FBHS (Aust) Pty Limited ABN 83 126 232 504 trading
More informationSTEEL BUILDINGS RECOMMENDED INSTALLATION GUIDE
STEEL BUILDINGS RECOMMENDED INSTALLATION GUIDE 3 TO 30 METRE SPAN TILT UP METHOD SUPPLIED BY: Last update 19 September 2011 2011 FBHS (Aust) Pty Limited FBHS (Aust) Pty Limited ABN 83 126 232 504 trading
More informationCURVED ROOF ASSEMBLY INSTRUCTIONS ATTACHED VERANDAH. Your supplementary guide to building an ATTACHED CURVED ROOF VERANDAH or PATIO BEFORE YOU START
ROOF ATTACHED VERANDAH ASSEMBLY INSTRUCTIONS Your supplementary guide to building an ATTACHED ROOF VERANDAH or PATIO This set of instructions should be used in conjunction with the Stratco instruction
More informationINSTRUCTION MANUAL FOR MULTIBUILD VERTICAL CLAD QUAKER BARN WITH OR WITHOUT OUT MEZZANINE FLOOR UP TO 12 METRE SPAN
INSTRUCTION MANUAL FOR MULTIBUILD VERTICAL CLAD QUAKER BARN WITH OR WITHOUT OUT MEZZANINE FLOOR UP TO 12 METRE SPAN SUPPLIED BY: LAST UPDATED March 11, 2003 2001 AG&S Building Systems, Sydney Australia
More informationSTEEL BUILDINGS RECOMMENDED INSTALLATION GUIDE
STEEL BUILDINGS RECOMMENDED INSTALLATION GUIDE 3 TO 30 METRE SPAN FRAME FIRST METHOD SUPPLIED BY: Last update 19 September 2011 2011 FBHS (Aust) Pty Limited FBHS (Aust) Pty Limited ABN 83 126 232 504 trading
More informationAppendix B Framing Component Installation Last updated 5/27/2013
Appendix B Framing Component Installation Last updated 5/27/2013 Apex Brace Installation Appendix B 1 Refer to apex connection detail on the engineering plans for the location of the apex brace. Refer
More informationClopay Models 835/837 Sliding Door System Installation Guide
Clopay Models 835/837 Sliding Door System Installation Guide The aim of this instruction is to guide you through the process of construction and fitting of Sliding Doors. Due to the number of sizes available
More informationCLEARSPAN GABLE STRATCO OUTBACK ASSEMBLY INSTRUCTIONS. WITH GAZEBO END ATTACHED PATIO
CLEARSPAN GABLE WITH GAZEBO END ATTACHED PATIO STRATCO OUTBACK ASSEMBLY INSTRUCTIONS. Your supplementary guide to building an ATTACHED CLEARSPAN GABLE VERANDAH or PATIO WITH GAZEBO END This set of instructions
More informationSTRATCO GABLE HOMESHED STRATCO GABLE HOMESHEDS STUBBIE INSTALLATION GUIDE
STRATCO GABLE HOMESHED STRATCO GABLE HOMESHEDS STUBBIE INSTALLATION GUIDE INSTALL GUIDE BEFORE YOU START COUNCIL APPROVAL It is important that you have local council approval before building your Stratco
More informationSafety Glasses Safety Gloves Ladders Measuring Tape Spirit Level String Line. Tin-Snips Rivet Gun Caulking Gun Silicone Socket Set
BEFORE YOU START Carefully read these instructions and refer to them constantly during each stage of construction. If you do not have all the necessary tools or information, contact Stratco for advice.
More informationBUILDING GUIDE FOR MULTIBUILD ALL STEEL BUILDINGS 3 TO 30 METRE SPAN
BUILDING GUIDE FOR MULTIBUILD ALL STEEL BUILDINGS 3 TO 30 METRE SPAN SUPPLIED BY: 26 Dobney Ave, Wagga Wagga. NSW. 2650 PH: 02 6925 5719, Fax 02 6925 2895 Email: sales@havashed.com.au, Web Address: www.havashed.com.au
More informationOutback Gable CLEARSPAN ATTACHED
It is important to check your Local Government Authority requirements before the installation of your new Stratco Outback Flat Verandah. It is the builderʼs responsibility to ensure any existing structure
More informationHow-To-build guide carport
How-To-build guide carport What you can build using this guide This guide will show you how to build a free-standing, open-sided single carport. Before you begin building Contact your local territorial
More informationMULTISPAN GABLE WITH HIP END ATTACHED PATIO
MULTISPAN GABLE WITH HIP END ATTACHED PATIO STRATCO OUTBACK ASSEMBLY INSTRUCTIONS. Your supplementary guide to building an ATTACHED MULTISPAN GABLE VERANDAH or PATIO WITH HIP END This set of instructions
More informationINSTALLATION GUIDE. Outback. Flat Attached BEFORE YOU START ADDITIONAL MATERIALS TOOLS REQUIRED. VERAnDAHS PATIOS CARPORTS
INSTALLATION GUIDE Outback VERAnDAHS PATIOS CARPORTS Flat Attached BEFORE YOU START It is important to check your Local Government Authority requirements before the installation of your new Stratco Outback
More informationOUTBACK FLAT ATTACHED VERANDAH PATIO CARPORT - INSTALLATION GUIDE BEFORE YOU START TOOLS REQUIRED ADDITIONAL MATERIALS
BEFORE YOU START It is important to check your Local Government Authority requirements before the installation of your new Stratco Outback Flat Verandah. It is the builder s responsibility to ensure any
More informationInstallation Guidelines
Page 1 Tools You ll Need 4 ft. Carpenter s level Chalk line (to mark U channel locations) Cordless drill/nut driver Caulking gun Chop saw with a metal cutting blade on it (required to make accurate and
More informationINSTRUCTION MANUAL FOR MULTIBUILD AMERICAN BARN
INSTRUCTION MANUAL FOR MULTIBUILD AMERICAN BARN SUPPLIED BY: LAST UPDATED April 26, 2006 2001 AS&G Building Systems AMERICAN BARN The American Barn uses similar components to other steel frame buildings.
More informationAppendix A Door and Window Framing Last updated 5/21/2013
Appendix A Door and Window Framing Last updated 5/21/2013 1. First complete all previous framing for bay. Appendix A 1 Install all applicable columns, rafters, and/or eave purlins for the bay in which
More informationStratco Sanctuary INSTALLATION BEFORE YOU START TOOLS REQUIRED GUIDE
INSTALLATION GUIDE Stratco Sanctuary Verandahs, Patios and Carports BEFORE YOU START It is important to check with your Local Government Authority prior to the installation of your new Stratco Sanctuary
More informationINSTALLATION GUIDE. Outback Clearspan Gable BEFORE YOU START ADDITIONAL MATERIALS ADDITIONAL MATERIALS WITH COOLDEK ROOFING
INSTALLATION GUIDE Outback Clearspan Gable WITH COOLDEK ROOFING BEFORE YOU START It is important to check your Local Government Authority requirements before the installation of your new Stratco Outback
More informationInstallation Guidelines
Page 1 Tools You ll Need 4 ft. Carpenter s level Chalk line (to mark U channel locations) Cordless drill/nut driver Caulking gun Chop saw with a metal cutting blade on it (required to make accurate and
More informationINSTALLATION GUIDE. Flat Roof Homesheds TM. Onto Concrete BEFORE YOU START TOOLS REQUIRED
INSTALLATION GUIDE Flat Roof Homesheds TM Onto Concrete BEFORE YOU START It is important to check your Local Government Authority requirements before the installation of your new Stratco Flat Roof Homeshed.
More information1 P a g e THIS IS A GENERIC MANUAL AND MAY NOT BE INDICATIVE OF YOUR CONSTRUCTION.
1 P a g e INDEX SECTION DESCRIPTION PAGE 1 TOOLS REQUIRED 3 2 GENERAL PARTS IDENTIFICATION.... 4 2.1 Structural Members 4 2.2 Brackets.. 4 2.3 Fasteners and Bolts 5 2.4 Roof and Wall Cladding.. 5 2.5 Gutters
More informationAbsco Premier Garden Shed Assembly Instructions Model: J30302G
Absco Premier Garden Shed Assembly Instructions FRONT: 9' 0 7 64" SIDE: 9' 0 7 64" HEIGHT: 6' 0 43 64" 0' 3 64" CONCRETE SLAB 0' 3 64" CONCRETE SLAB WHEN LAYING YOUR CONCRETE SLAB, ENSURE THERE IS A REBATED
More informationEnsure there is reasonable access for materials and working space, ensure the shed site is level and consider the disposal of run-off water.
INSTALLATION GUIDE TM Flat Roof Homesheds THE POTTER BEFORE YOU START It is important to check your Local Government Authority requirements before the installation of your new Stratco Potter Flat Roof
More informationAbsco Premier Garden Shed Assembly Instructions Model: J30302G
Absco Premier Garden Shed Assembly Instructions FRONT: 9ft-0-7 64in SIDE: 9ft-0-7 64in HEIGHT: 6ft-0-43 64in 0ft--3 64in CONCRETE SLAB 0ft--3 64in CONCRETE SLAB WHEN LAYING YOUR CONCRETE SLAB, ENSURE THERE
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS FOR AZTEC SHELTER
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS FOR AZTEC SHELTER ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will
More informationW L. Standard Sizes: 2.125m underside of gutters m total height m roof m roof m roof.
H Standard Sizes: H 2.125m underside of gutters. 2.280m total height. L L 5.450m roof. 6.050m roof. 7.250m roof. W W 3.000m roof/2.640m between posts. 3.600m roof/3.240m between posts. 5.400m roof/5.040m
More informationINSTALLATION GUIDE. Flat Roof Homesheds TM BEFORE YOU START TOOLS REQUIRED
INSTALLATION GUIDE Flat Roof Homesheds TM BEFORE YOU START It is important to check your Local Government Authority requirements before the installation of your new Stratco Flat Roof Homeshed. Read these
More information6 1/2 x 6 1/2 Flat Top Pergola
6 / x 6 / Flat Top Pergola A S S E M B L Y G U I D E Models: Portland, Liberty O P T I O N A L A C C E S S O R Y Bolt Down Bracket Kit V.-0506 Ta b l e o f Co n t e n t s PAGE The Introduction & Overview......................................................
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will not be responsible
More informationGable HomeshedsTM INSTALLATION BEFORE YOU START TOOLS REQUIRED GUIDE LARGE SPAN. Council Approval. Before Starting
INSTALLATION GUIDE Gable HomeshedsTM LARGE SPAN BEFORE YOU START Council Approval It is important to contact your local council before building your Stratco Gable Homeshed. You will have already received
More informationLocker Pedestal Installation Instructions
Locker Pedestal Installation Instructions LK-PED-INST-0314r1 Parts List Single Pedestal Back to Back Pedestal Horizontal Support Tube TS-169 Post Flange TS-190 Post Cap Fasteners Provided: #8 x ¾ round
More informationAbsco Regent Shed Assembly Instructions Model: J30372R
Absco Regent Shed Assembly Instructions FRONT: 9ft-0-7 64in SIDE: ft-3 3in HEIGHT: 6ft-0-43 64in ft-4-3in CONCRETE SLAB 0ft--3 64in CONCRETE SLAB WHEN LAYING YOUR CONCRETE SLAB, ENSURE THERE IS A REBATED
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will not be responsible
More information6 1/2 x 6 1/2 Wood Grain Flat Top Pergola
6 / x 6 / Wood Grain Flat Top Pergola A S S E M B LY G U I D E Models: Lakewood OPTIONAL ACCESSORY Bolt Down Bracket Kit Ver /AUG/0 Ta b l e o f Co n t e n t s PAGE The 6.5 x 6.5 Wo o d Grain Flat Top
More information10x10 Trellis Pergola
0x0 Trellis Pergola ASSEMBLY GUIDE Ver.0-7 Table of Contents PAGE Introduction & Overview...................................................... Pergola Materials Overview..............................................................
More informationInstallation Guide Simplicity 6. v3.5 lu171117
0845 869 6006 www.canoports.co.uk Installation Guide Simplicity 6 v3.5 lu171117 Tools Required Below is a list of tools that you will require to install the Simplicity 6 Canopy or Carport. Cordless Drill
More informationGLOSSARY OF TERMS SECTION 8
GLOSSARY OF TERMS SECTION 8 Anchor Bolt Angle Base Plate Bay Blocking CCB Centerline Chord Cladding Clip Closure Strip An A-307 steel bolt embedded in the concrete footing to anchor the base plate of the
More informationPINEHAVEN SHEDS Assembly Instructions FOR LEAN-TO SHEDS
PINEHAVEN SHEDS Assembly Instructions FOR LEAN-TO SHEDS GARDEN PRODUCTS www.pinehavensheds.co.nz 5/16 hex drive bit, By asking about our products at your nearest DIY or gardening store www.pinehavensheds.co.nz
More informationASSEMBLY INSTRUCTIONS FOR SOFTOP SHADE COVER
ASSEMBLY INSTRUCTIONS FOR SOFTOP SHADE COVER Our unique assembly process quickly transforms individual pieces into a finished structure that will give you a lifetime of service. Great care has been taken
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will not be responsible
More information10x10 Trellis Pergola
0x0 Trellis Pergola ASSEMBLY GUIDE Ver.-007 Table of Contents PAGE 0x0 Trellis Pergola Introduction & Overview...................................................... Pergola Materials Overview..............................................................
More informationVINYL CLASSIC FREESTANDING PERGOLA ASSEMBLY INSTRUCTIONS
P a g e 1 VINYL CLASSIC FREESTANDING PERGOLA ASSEMBLY INSTRUCTIONS Shown: 8' x 12' Vinyl Classic Pergola with 12" Top and Main Runner Spacing The design of this pergola is based on all posts being installed
More information4-SIDED NAVAJO SHELTER ARIZONA MODEL INSTALLATION INSTRUCTIONS
4-SIDED NAVAJO SHELTER ARIZONA MODEL INSTALLATION INSTRUCTIONS Recommended Tools: Before You Begin: Saftey Glasses, Tape Measure, Carpenters Level, Framing Square, Hex Head Nut Drivers, Chalk Line, Elec.
More information8 x 8 Flat Top Pergola
A S S E M B L Y G U I D E O P T I O N A L A C C E S S O R Y Bolt Down Bracket Kit Models: Mirage, Mandalay Ver 6/00 Ta b l e o f Co n t e n t s Introduction & Overview......................................................
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will not be responsible
More informationInstallation Guide Simplicity 16. V2.9 Lu171117
0845 869 6006 www.canoports.co.uk Installation Guide Simplicity 16 V2.9 Lu171117 Tools Required Below is a list of tools that you will require to install the Simplicity 16 Canopy or Carport. Cordless Drill
More informationHow-To-build guide Garden shed
How-To-build guide Garden shed What you can build using this guide This guide will show you how to build a re-locatable garden shed. Before you begin building Contact your local territorial authority to
More informationINSTALLATION INSTRUCTIONS FOR ULTRA LATTICE AND ALUMAWOOD ARBORS
INSTALLATION INSTRUCTIONS FOR ULTRA LATTICE AND ALUMAWOOD ARBORS GENERAL INFORMATION: Lattice arbors are designed to be freestanding or attached. They are designed to resist a 10 lb. to 30 lb. per square
More informationCall (770) STEP 6: Caulk bolt hole within the bracket for protection from the elements.
Call (770) 777 7007 Structural Deck Support System: Product Numbers: H1-GQ, H2-GCL (Also applies to H1-GK and H2-GCR) STEP 1: Following the spacing guidelines per the deck design and joist layout, mark
More informationALL SEASON PATIO COVER
ALL SEASON PATIO COVER 61 Where the All Season Patio Cover is to be attached to the home, create a level line showing where the top of the mounting rail is to be located. Install each section with the
More informationASSEMBLY INSTRUCTIONS GG77. BASE SIZE: 2.190m x 2.020m
ASSEMBLY INSTRUCTIONS GG77 BASE SIZE: 2.190m x 2.020m CONGRATULATIONS ON PURCHASING A DURATUF GUARDIAN SHED. BEFORE YOU BEGIN THE ASSEMBLY PLEASE NOTE SOME IMPORTANT POINTS: BEFORE YOU START: Read all
More informationBelham Living Harbor Bay Pergola
Belham Living Harbor Bay Pergola A S S E M B LY G U I D E OPTIONAL ACCESSORY Bolt Down Bracket Kit Models: Ver.0-08065 Belham Living Harbor Bay Ta b l e o f Co n t e n t s B elham Living Harbor Bay Pergola
More informationLenox Slide Lock Pergola
ASSEMBLY GUIDE Models: Lenox OPTIONAL ACCESSORIES Bolt Down Bracket Kit ( for Pergola) Ver.0-076 Table of Co n t e n t s Introduction & Overview...................................................... Pergola
More informationSHED PACK Step 1: Choose your shed type.
SHED PACK Step 1: Choose your shed type. Industrial Shed Open FarmShed Shed Pack / Types of Sheds Drawing # S0104.A001 Hanger Shed =DISCLAIMER= Please read and agree to Purlin Brackets Terms and Conditions
More informationDura-Lock Roof System
DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.
More informationASSEMBLY INSTRUCTIONS GL75. BASE SIZE: 2.190m x 1.520m
ASSEMBLY INSTRUCTIONS GL75 BASE SIZE: 2.190m x 1.520m CONGRATULATIONS ON PURCHASING A DURATUF GUARDIAN SHED. BEFORE YOU BEGIN THE ASSEMBLY PLEASE NOTE SOME IMPORTANT POINTS: BEFORE YOU START: Read all
More information12 x 12 Flat Top Pergola
x Flat Top Pergola Model: Regency, Roosevelt A S S E M B L Y G U I D E O P T I O N A L A C C E S S O R Y Bolt Down Bracket Kit ( for Pergola) Ver./MAR 0 Ta b l e o f Co n t e n t s PAGE x Flat Top Pergola
More information10 x 10 Flat Top Two Tone Pergola
0 x 0 Flat Top Two Tone Pergola Models: Bordeaux ASSEMBLY GUIDE OPTIONAL ACCESSORIES Arch Kit System ( Arches) Privacy Fence Panel System ( Panels & Middle Post) Bolt Down Bracket Kit ( for Pergola) Ver.0-00
More informationASSEMBLY INSTRUCTIONS SS2520. BASE SIZE: 2.520m x 2.020m
ASSEMBLY INSTRUCTIONS SS50 BASE SIZE:.50m x.00m CONGRATULATIONS ON PURCHASING A SMART STORE SHED. BEFORE YOU BEGIN THE ASSEMBLY PLEASE NOTE SOME IMPORTANT POINTS: BEFORE YOU START: Read all instructions
More informationPOST FRAME CONSTRUCTION MANUAL
POST FRAME CONSTRUCTION MANUAL www.pole-barn.info www.apbbuildings.com TABLE OF CONTENTS 3. Jobsite Preparation 4. Setting Foundation Posts 5. Setting Corner Posts 6. Sidewall & Endwall Posts 7. Grade
More informationDouble Beam Freestanding Pergola Installation Guide
Double Beam Freestanding Pergola Installation Guide Patent Pending. Copyright 2011 USAVinyl, LLC - All Rights Reserved The information contained in these instructions are proprietary to USAVinyl, LLC and
More information6 1/2 x 6 1/2 Wood Grain Flat Top Pergola
/ x / Wood Grain Flat Top Pergola A S S E M B LY G U I D E Models: Lakewood OPTIONAL ACCESSORY Bolt Down Bracket Kit V.- Ta b l e o f Co n t e n t s The PAGE Introduction & Overview.......................................................
More informationAbsco Premier Garden Shed Assembly Instructions Model: 23231GK
Absco Premier Garden Shed Assembly Instructions Model: 33GK FRONT:.6m SIDE:.6m HEIGHT:.00m 360mm CONCRETE SLAB 360mm WHEN LAYING YOUR CONCRETE SLAB, CHAMFER THE 50mm EDGES DOWNWARDS BY 0mm. 50mm 0mm 50mm
More informationASSEMBLY INSTRUCTIONS SS2010. BASE SIZE: 2.020m x 1.020m
ASSEMBLY INSTRUCTIONS SS010 BASE SIZE:.00m x 1.00m CONGRATULATIONS ON PURCHASING A SMART STORE SHED. BEFORE YOU BEGIN THE ASSEMBLY PLEASE NOTE SOME IMPORTANT POINTS: BEFORE YOU START: Read all instructions
More informationResidential & Industrial Fence
Page Residential & Industrial Fence Assembly Instructions Congratulations on the purchase of your new Fence System. Your fence has been designed to give you years of trouble free service with only minimal
More informationEnglish/French 06/04
E000 PLEASE READ ASSEMBLY INSTRUCTIONS COMPLETELY BEFORE ASSEMBLING YOUR BUILDING CAUTION: Some parts have sharp edges. Care must be taken when handling the various pieces to avoid a mishap. For safety
More information8 x 8 Flat Top Pergola
A S S E M B L Y G U I D E O P T I O N A L A C C E S S O R Y Bolt Down Bracket Kit Models: Mirage, Mandalay Ver 8.0/MAR 0 Ta b l e o f Co n t e n t s PAGE Introduction & Overview......................................................
More informationHANDI-MATE SHED BEFORE YOU START INSTALL GUIDE HINGED DOOR HANDI-MATE INSTALLATION GUIDE PRIOR TO INSTALLATION
HANDI-MATE SHED HINGED DOOR HANDI-MATE INSTALLATION GUIDE INSTALL GUIDE BEFORE YOU START PRIOR TO INSTALLATION It is important that you contact your local government authority to determine if building
More informationAssembly Book. the Fairview. Building Size 12'x12' Revised July 25, 2012
Assembly Book Revised July 25, 2012 the Fairview Building Size 12'x12' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationTHANK YOU FOR PURCHASING FROM HERITAGE PATIOS
Installation Guide THANK YOU FOR PURCHASING FROM HERITAGE PATIOS Your purchase is engineered by nearly a half century of commercial and residential product design proudly manufactured in the USA from responsibly
More informationExtrusions POLYLOCK ATTACHING EXTRUSIONS
Extrusions POLYLOCK ATTACHING EXTRUSIONS ITEM # DESCRIPTION USES 1001 Aluminum Girt 16 lengths Used in metal end packages and sidewalls as horizontal members. Requires girt/baseboard splice (#1000). 1000
More informationOxford Stalls Installation Instructions
Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or
More informationASSEMBLY INSTRUCTIONS
GARDEN SHED 6X5ft B/C 9400988362649 GARDEN SHED 6X7ft B/C 9400988362656 GARDEN SHED 6X9ft B/C 9400988362663 GARDEN SHED 6X1 B/C 9400988362670 111 ft ASSEMBLY INSTRUCTIONS Product specifications may change
More informationThe Mirage Pergola ASSEMBLY GUIDE. OPTIONAL ACCESSORY Bolt Down Bracket Kit. Ver 3/2009
ASSEMBLY GUIDE OPTIONAL ACCESSORY Bolt Down Bracket Kit Ver /009 Table of Contents PAGE Introduction & Overview...................................................... Mirage Pergola Materials Overview.....................................................
More informationSHED PACK. Sheds are commonly constructed using portal frames.
SHED PACK Sheds are commonly constructed using portal frames. This pack relates to purchasing portal frame purlin bracket sets. Ruest our free generic engineered and certified shed plans. SHED PACK Step
More informationSteelChief Installation Instructions for pre-assembled panel form sheds GABLE ROOF
SteelChief Installation Instructions for pre-assembled panel form sheds GABLE ROOF Please read fully before commencing work...any queries will be promptly answered, contact theboss@steelchief.com.aui MPORTANT
More informationAbsco Space Saver Shed Assembly Instructions Model: J30082S
Assembly Instructions FRONT BASE LENGTH: 9' 0 7 64" SIDE BASE LENGTH: ' 6 45 64" FRONT WALL HEIGHT: 5' 0 55 64" REAR WALL HEIGHT: 6' 4 49 64" CONCRETE SLAB ' 0 4 64" 0' 3 64" CONCRETE SLAB WHEN LAYING
More informationLAS VEGAS PATIO COVER INSTALLATION INTSRUCTIONS
STEP 8. Drill 2-5/8" dia. holes in the outer face of the ledger board spaced evenly (approximently 24" O.C.). Hoist the ledger board into place, centering it in front of the gutter. Anchor the inner face
More information6 1/2 x 6 1/2 Wood Grain Flat Top Pergola
/ x / Wood Grain Flat Top Pergola A S S E M B LY G U I D E Models: Lakewood OPTIONAL ACCESSORY Bolt Down Bracket Kit V.-09 Ta b l e o f Co n t e n t s The PAGE Introduction & Overview.......................................................
More informationMODERN PERGOLA INSTALLATION GUIDE. When only the best will do.
MODERN PERGOLA INSTALLATION GUIDE When only the best will do. TOOLS LIST Drill(s) 3/8" Magnetic Driver (s) 12" Drill Extension #2 Square Drive bit for Drill or Driver Level Tape Measure Hammer Drill if
More information10 x 10 Flat Top Pergola
0 x 0 Flat Top Pergola A S S E M B L Y G U I D E Models: Venetian, Tuscany, Luxor, Acadia O P T I O N A L A C C E S S O R I E S Arch Kit System ( Arches) Privacy Fence Panel System ( Panels & Middle Post)
More informationPRE-ENGINEERED HORSE STALL SYSTEMS SDFD SLIDING DOOR c/w FOLD-DOWN GRILL. & Assembly. Installation Instructions
PRE-ENGINEERED HORSE STALL SYSTEMS 4800 SDFD SLIDING DOOR c/w FOLD-DOWN GRILL & Assembly Installation Instructions 4800 SDFD Sliding Door c/w Fold-Down Grill Components - 1 3 /4" x 2" x 88" channels (2)
More informationGrowSpan Estate Pro I Greenhouse
GrowSpan Estate Pro I Greenhouse Photo may show a different but similar model. 2016 Growers Supply All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 104564 11'-8" W x
More informationInstallation Guide Simplicity Alfresco. V1.9 Lu070318
0333 305 5272 www.canoports.co.uk Installation Guide Simplicity Alfresco V1.9 Lu070318 Tools Required Below is a list of tools that you will require to install your the Simplicity Alfresco System. Cordless
More informationMUELLER
Slab Mounted: 24x24 Backyard Building with Optional Center Girts Instructions Mueller Backyard Building Kits are not engineered structures and do not meet any specific building code criteria. 877-2- MUELLER
More informationNEVADA ASSEMBLY INSTRUCTIONS
NEVADA ASSEMBLY INSTRUCTIONS BASE SIZE: 2.700m x 1.500m NEVADA Tools Required: Battery Drill Riveter Hammer Tape Measure Ladder Skillsaw Level Screwdriver - Flat 3/8 Hex Drive bit 8mm Hex Drive bit Drill
More informationDESIGNER GABLE INSERT
DESIGNER GABLE INSERT CONSTRUCTION GUIDE 1 DESIGNER GABLE INSERT CONSTRUCTION GUIDE CONTENTS 1. Disclaimer 2 2. General notes before using this guide 3 3. Glossary of terms 4 4. Component assembly diagram
More informationInstallation Guide Contemporary Alfresco V1.3 LU
Installation Guide Contemporary Alfresco V1.3 LU 010818 Tools Required Below is a list of tools that you will require to install you're the Contemporary Alfresco System. Cordless Drill Mastic Gun Spirit
More informationModel No. EP84-A, EP84AR-A, P84L
E000 Model No. EP84-A, EP84AR-A, P84L PLEASE READ ASSEMBLY INSTRUCTIONS COMPLETELY BEFORE ASSEMBLING YOUR BUILDING CAUTION: Some parts have sharp edges. Care must be taken when handling the various pieces
More informationRevision Date: April 01, Paramount Enclosure
Paramount Enclosure www.urbanindustries.com 15 Urban Industries, Inc. 2008 Tools The following tools are recommended for the installation of the Paramount Aluminum Enclosure and roof. 1 2 Level 1 4 Level
More informationInstallation Manual For ToddPod Outdoor Shower Enclosures
Installation Manual For ToddPod Outdoor Shower Enclosures Contact us at 888-545-9763 or email us at office@toddpod.com with any questions during the installation process. Our service team is available
More informationIDAHO ASSEMBLY INSTRUCTIONS. BASE SIZE: 1.800m x 1.200m
IDAHO ASSEMBLY INSTRUCTIONS BASE SIZE: 1.800m x 1.200m IDAHO Tools Required: Battery Drill Riveter Hammer Tape Measure Ladder Skillsaw Level Square Drive Bit No.2 3/8 Hex Drive Bit 8mm Hex Drive Bit Drill
More informationORP-F1 Regular: Basic / J-Connection / M-Connection
D636 ORP-F Regular: Basic / J-Connection / M-Connection Construction Manual Thank you for purchasing our product. The indication symbols in this construction manual are for you to construct the product
More information