Timber Connectors & Post Anchors. Click to start

Transcription

1 Timber Connectors & Post Anchors Click to start

2 Pryda Pryda has been an integral part of the building industry in Australia for over 40 years, particularly in timber truss and frame solutions with the development of a diverse range of timbers connectors, structural brackets and post anchors. Pryda provides support to architects and builders in terms of engineering advice and support, and access to product image files for placement on building plans. Pryda ensures that its products meet Australian Standards and comply with the Builders Code of Australia. Use of noncompliant products could lead to a possible risk of failure with the builders design and result in significant rectification costs.

3 Product Bracing Tie-Down Connectors Hangers & Truss Boots Nail Plates Brackets Fixes Builder s Hardware Timber & Connector Nails Post Anchors

4 Bracing Pryda Bracing products have been developed to be structurally sound and cost effective for bracing of roofs, walls, floors and other parts of timber framed buildings. They are designed to meet the code bracing requirements and have been laboratory tested to assure their strength, since computations without testing has shown to be an unreliable basis for assessment of performance. For fixing of all Pryda Bracing, it is essential to use galvanised Pryda Timber Connector Nails, ie. The special 35x3.15mm nails developed specifically for fixing of Pryda products. Laboratory strength testing has shown that clouts are not adequate for this purpose as their heads may pop off under less than design loads. Fixing into steel supporting structures: Pryda products can be fixed into stell using Teks screws or similar. Strap Brace Speed Brace Angle Brace: Mini and Maxi Brace

5 Bracing Strap Brace Pryda Strap Brace with Tensioner, is an easy to use, flat strap, steel bracing for roofs, walls, ceilings and floors. Pryda Strap Brace complies with the wall bracing rules of AS1684 Residential Timber-Framed Construction and has excellent advantages including: Saves on-site labour time as studs do not have to be notched. The un-notched studs can often be a smaller size and hence cheaper than notched studs. Available in long length coils for ease of handling and minimum wastage. Easily and quickly tensioned using the Strap Brace Tensioner. Pryda Strap Brace is ideal for bracing applications where timber braces are not feasible because of their thickness or because timber can t be bent, e.g. Exposed beams or rafters, or trusses. All Pryda bracings are manufactured from G300 Z275 ZincForm steel or equivalent for high strength and corrosion resistance in normal, interior uses.

6 Bracing Speedbrace Pryda Speedbrace, used as diagonal roof bracing, provides overall stability to the trussed roof and, in conjunction with the roof battens, presents lateral buckling of the top chords. Pryda Speedbrace is also suitable for use as wall bracing. Pryda Speedbrace is spliced by overlapping lengths of brace hammering flat and nailing with the same number of galvanised Pryda Timber Connector Nails as is required at the top of the plate. Advantages: Pryda Speedbrace is applied on top of the top chord, eliminating the difficulty of applying a brace to the underside of the chord as is necessary with conventional timber braces. The profile of the Speedbrace allows it to be applied without the need for tensioners as the rib merely needs to be hammered flat where it crosses the timber members. Speedbrace can be spliced easily and can be wrapped around members to provide a sound and secure anchorage. All Pryda bracings are manufactured from G300 Z275 ZincForm steel or equivalent for high strength and corrosion resistance in normal, interior uses.

7 Bracing Angle Brace: Mini & Maxi Brace Pryda Mini Brace and Maxi Brace can be used as bracing or nogging of Type A Bracing Units in wall frames in accordance with AS Residential Timber Framed Construction and The Wall Bracing Units Construction Code. All Pryda bracings are manufactured from G300 Z275 ZincForm steel or equivalent for high strength and corrosion resistance in normal, interior uses.

8 Tie-Down Connectors Batten Straps Bottom Plate Anchor Cyclone Straps Joist Strap Mitre Plates Multigrips & Minigrips Pryda Hitch Stud Ties Triple Grips High Capacity Tie-Down Plates Hold-Down Angle Bracket Cyclonic Grips Truss Tie Unitie

9 Tie-Down Connectors Batten Straps Economical, easy to use, Roof Batten Connectors and Tie Down Connector. Pryda Batten Straps are used for tying down roof battens to trusses or rafters. They are: Easy and quick to install Save construction time and cost Meet tie-down requirements for all wind zones including C3 To install Pryda Straps & Ties; use only 35 x 3.15mm galvanised Pryda Timber Connector Nails.

10 Tie-Down Connectors Bottom Plate Anchor A pressed steel bracket for fixing timber bottom plates to a concrete slab floor. Pryda Bottom Plate Anchors replace concrete nail fixing of bottom wall plates to a concrete slab. To install Pryda Straps & Ties; use only 35 x 3.15mm galvanised Pryda Timber Connector Nails.

11 Tie-Down Connectors Cyclone Straps Pryda Cyclone Straps are used primarily in cyclonic areas for tying down purlins to trusses or roof trusses or other roof members to the wall frame. They are: Quick and easy to install Sufficient capacity for many cyclonic area uses Can be doubled up for twice tie-down capacity requirements of lengths to suit different nailing capacity requirements Maximum design capacity determines from Pryda tests To install Pryda Straps & Ties; use only 35 x 3.15mm galvanised Pryda Timber Connector Nails.

12 Tie-Down Connectors Joist Straps A simple joist strap with a variety of uses in building. Pryda Joist Strap is a simple, bent metal strap with an in-built nail and nail holes for fixing with 35 x 3.15mm galvanised Pryda Timber Connector Nails. It is ideal for connecting timber members at right angles such as floor joists to bearers, hanging beams to ceiling joists, rafters to beams, purlins to rafters or trusses. To install Pryda Straps & Ties; use only 35 x 3.15mm galvanised Pryda Timber Connector Nails.

13 Tie-Down Connectors Mitre Plates Pryda Hip Mitre Plates are used for connecting creeper trusses to hip trusses. They: Are easy and quick to install being factory bent to suit the common 45 degrees angle between most creeper and hip trusses. Can also be used with rafters. The angle of bend in the Mitre Plate stops the top corner from protruding above the line of the roof. Meet the requirements in AS (refer to Pryda design loads) Are available at right handed and left handed. This is required to pick up the creeper from both sides of the hip. Pryda Hip Mitre Plates require 5/35 x 3.15 galvanised Pryda Timber Connector Nails into the creeper top or bottom chord, and the same into the hip truss chords.

14 Tie-Down Connectors Minigrips Pryda Minigrips provide a more economical connector for the numerous, more lightly loaded joints in houses and other buildings. Multigrips Pryda Multigrips are ideal connectors for many uses in timber framing. They are suitable for high load applications such as a tie-down connector for trusses or rafters to top plates and for fixing joists to the face of bearers. To install Pryda Straps & Ties; use only 35 x 3.15mm galvanised Pryda Timber Connector Nails.

15 Tie-Down Connectors Pryda Hitch Bracket which stabilises internal, non-load bearing walls from bottom chords of trusses. Pryda Hitch stabilises the tops of internal walls by fixing them laterally to the bottom chord of roof trusses. Pryda Hitch has built in slots which allow for vertical movement in the truss over time without transferring load to the wall. To install Pryda Straps & Ties; use only 35 x 3.15mm galvanised Pryda Timber Connector Nails.

16 Tie-Down Connectors Stud Ties A quick, neat and effective connector between studs and wall plates. Pryda Stud Ties greatly improve the jointing of top and bottom plates to studs compared to the common nail fixing, ie.: Greater tie-down strength: Stud Tie nails are driven into the side grain of the stud to resist wind uplift in lateral shear. This is far stronger than relying on the withdrawal strength of common nails in end grain. No splitting of the timber: with Stud Ties, the careful location of the nails away from timber ends and edges avoids splitting which can occur in common nails only joints, expecially in some timbers and particularly with skew nailing. Convenience: The Stud Ties have in-built nails, there is no need for other nails. Stud Ties are quick and easy to apply, the in-built nails are readily driven home with a conventional hammer. Single Sided Double Sided To install Pryda Minigrips, Multigrips or Triplegrips; use only 35 x 3.15mm galvanised Pryda Timber Connector Nails.

17 Tie-Down Connectors Triple Grips Pryda Triple Grips are used for many nail fixed timber joints, e.g. roof truss to wall plate; rafter or ceiling joist to wall plate; purlin to truss; hanger to ceiling joist; or wall stud to bottom plate. To install Pryda Minigrips, Multigrips or Triplegrips; use only 35 x 3.15mm galvanised Pryda Timber Connector Nails.

18 Tie-Down Connectors High Capacity Tie-Down Plates Pryda High Capacity Tie-Down (HCTD) Plates are used for extreme tie-down situations, typically encountered with girder trusses in cyclonic areas. To install Pryda Minigrips, Multigrips or Triplegrips; use only 35 x 3.15mm galvanised Pryda Timber Connector Nails.

19 Tie-Down Connectors Hold-Down Angle Bracket Pryda Hold-Down Angle Bracket can be used in a variety of applications in timber structures. Providing tie-down resistance for roof trusses or wall studs is the most common usage of this product. This bracket is specially useful to achieve a concealed connection. To install Pryda Minigrips, Multigrips or Triplegrips; use only 35 x 3.15mm galvanised Pryda Timber Connector Nails.

20 Tie-Down Connectors Cyclonic Grips Pryda Cyclonic Grips will be generally used in cyclonic areas for tying down roof trusses or other roof members to the wall frame. They can also be used to tie-down wall plates to studs. The PCG grips are designed specially to be fixed into typical heavy-duty steel wall plates and the PCG90, on the other hand, is targeted for standard 90mm framing (steel or timber). To install Pryda Minigrips, Multigrips or Triplegrips; use only 35 x 3.15mm galvanised Pryda Timber Connector Nails.

21 Tie-Down Connectors Truss Ties The Pryda Truss Tie is a fixing device that has been designed to tie down roof trusses or rafters to a timber top plate. They are easy and quick to install having preformed teeth that allow it to be hammered in without nails. Truss ties are typically used for low tie-down requirement, for concrete tile roofs. Truss ties may be used in pairs to achieve double the capacity. To install Pryda Stud & Truss Ties; use only 35 x 3.15mm galvanised Pryda Timber Connector Nail.

22 Tie-Down Connectors Unitie Universal ties for joining timber at right angles. Pryda s Unitie is a simple metal tie for joining timbers cording at right angles. Typical applications include purlin to rafter or truss top chord; rafter or truss to wall frame top plate. To install Pryda Stud & Truss Ties; use only 35 x 3.15mm galvanised Pryda Timber Connector Nail.

23 Hangers and Truss Boots Beam Hangers I-Joist Hangers LVSIA Angle Brackets Framing Brackets Joist Hangers Truss Boots (Heavy Duty) Truss Boots (Multi Fix) Hip Brackets

24 Hangers and Truss Boots Beam Hangers Pryda Beam Hangers are heavy duty welded handers for connection of large size beams of Iarge size beams of I-joists, ranging in thickness from 45mm to 180mm, to timber beams or masonry walls. Pryda Beam Hangers are: Easy to install with a small number of coach screws and/or nails onto timber or with masonry anchors onto masonry or concrete. An economical means of forming these connections Ideal for supporting heavily loaded beams on fire rated brick walls, eliminating the need for a girder truss or false wall to support the beams. 180mm wide hangers support double I-joists. The Pryda BBT Beam Hanger is a heavy duty welded hanger for connection of large sized strutting beams placed at angles between 30 and 60 degrees, to timber beams or masonry walls. This bracket is commonly adopted in Western Australia.

25 Hangers and Truss Boots I-Joist Hangers Face mount and to mount hangers for timber I-joists. Pryda I-Joist Hangers are: Ideally suited to support modern timber I-Joists Use of full depth hangers provides torsional restraint to the I-joist. There is provision for a screw through the hanger into the bottom of the bottom flange to minimise squeaking. A hole towards the bottom of each side flange is also available for fixing into bottom flange to further reduce the effect of squeaking. Top Mounted Skewed Var Slope Skewed Face Mounted To install Pryda Joist and I-Joist Hangers; use 35 x 3.15mm galvanised Pryda Timber Connector Nails.

26 Hangers and Truss Boots LVSIA Angle Brackets LVSIA is a versatile bracket that can be used in a horizontal direction as an angle SEAT to support beams or trusses coming in at any direction. This angle bracket can also be used in a vertical direction as an angle CLEAT for beam to beam connections especially in situations where normal joist hangers cannot be used.

27 Hangers and Truss Boots Framing Brackets Brackets for beam to beam, or beam to brickwork / concrete connections.

28 Hangers and Truss Boots Joist Hangers (Multi Fix) Metal brackets for truss to truss connections. Pryda Multi-Fix Truss Boots are used to connect roof trusses or other roof members to supporting girder trusses and they comprise: Joist Boots used for end support of joists and beams, and support of lightly loaded trusses from girder trusses. Truss Boots used for support of standard trusses. Multi-fix means that these connectors can be fixed with bolts or screws together.

29 Hangers and Truss Boots Truss Boots (Heavy Duty) Steel Brackets for Heavy Roof Truss to Truss Connections. The long anti-rotation fin and heavy duty steel of Pryda Heavy Duty Truss Boots, combined with the inherent high stiffness of the carried truss, prevents twisting of the bottom chord of the girder. Consequently, anti-rotation bars are not necessary. Useful variations of this product have welded hinges to allow for any angle (TB80V). The TBHD75 and TBHD75/T Truss Boots have further benefits which include: Special shape to reduce weight, and rounded edges for easier handling Improved bearing capacity for supported truss. A unique slot in the back of the boot to eliminate the need to cut 6-10mm from the heel of the supported truss. Additional screw fixings into supported trusses to improve uplift capacity, if required. Nail holes in the back flange to allow the boot to be easily located on the girder truss prior to drilling for bolts. Holes in the base to allow screw to hold any incoming angled member at ceiling level (such as a hip truss) in position. These holes are countersunk to allow flush finish if required. The twin-fin of TBHD75/T has been specially developed to enhance uplift capacities and meet the demands of girder to girder connections in cyclonic regions. Note: Screws are required in combination with bolts to achieve the desired uplift capacities.

30 Hangers and Truss Boots Truss Boots (Multi Fix) Metal brackets for truss to truss connections. Pryda Multi-Fix Truss Boots are used to connect roof trusses or other roof members to supporting girder trusses and they comprise: Joist Boots used for end support of joists and beams, and support of lightly loaded trusses from girder trusses. Truss Boots used for support of standard trusses. Multi-fix means that these connectors can be fixed with bolts or screws together.

31 Hangers and Truss Boots Hip Brackets Hip Brackets (HSB) are used to connect hip trusses or hip rafters to supporting girder trusses at a girder to girder junction.

32 Nail Plates Connector Plates Corner Plates Knuckle Nailplates Mini Nail Nail On Plates Pole Cats Strap Nails

33 Nail Plates Connector Plates Pryda Connector Plate is a quick, simple, economical and easy to use connector for jointing timber wall plates normally jointed by more time consuming conventional methods. The square slots allow for skew nailing when required. Applications include: Top plate corner connection Intersection of top plates Floor or ceiling joist or rafter Post and beam connection Butt join on top plate Floor bearers at support points For maximum efficiency, use three 35 x 3.15 mm galvanised Pryda Timber Connector Nails each side of the joint. To install Pryda Connector Plates use only 35 x 3.15mm galvanised Pryda Timber Connector Nails.

34 Nail Plates Corner Plates Galvanised bracket for right angle joints. The Pryda Corner Plate is especially designed for jointing corner timbers in light framing applications such as gate frames, and also a wide range of other uses including wall frames, tops of pergola eams, furniture framing etc. Suitable for use as either left or right hand and either the vertical or horizontal position.

35 Nail Plates Knuckle Nailplates Hammer Fixed, Easy to Use Nailplates for many applications. Pryda Knuckle Nailplates are galvanised steel connectors with inbuilt, bent-up knuckle nails. These plates are ideal for many structural and non-structural timber jointing and timber protection uses. Applied simply by hammering in the knuckle nails, these plates are used by tradesmen, home owners, frame and box manufactures, electricity supply authorities and builders. Special pressing equipment is not necessary. Among the many uses of Knuckle Nailplates, the most common are: jointing of wall frames together on-site on-site splicing of timber beams reinforcement of corners of boxes and bins reinforcement of bolted joints (eg: in Cable Truss) truss manufacture in areas with low labour costs. Generally, Knuckle Nailplates: provide a strong, economical and easy-to-use means of jointing timber together protect timber from damage as they: resist splitting due to drying of the timber, nailing near ends or other causes eg: Bin Straps; resist the effects of impact loads. dissipate electricity current surges in cross arms over a larger area (eg: Shunt plates) distribute concentrated loads over a wider area. For example, they increase the strength of bolted joints. hold joints together, preventing or restricting the separation of nailed joints such as in boxes and crates, eg: Bin Straps. Pryda Knuckle Nail Plates, Mininails and Strap Nails are manufactured from G300 Z275 ZincForm steel or equivalent.

36 Nail Plates Mininail A pre-punched, mini nailplate for joining or connecting timber. Pre punched nails Sharp tooth profile penetrates readily into hardwoods and softwoods. Can be used as a mini joiner for narrow timber or for fixing fabric/foil timber Suitable for both trade use (e.g. furniture manufacture) or handy person application Manufactured from 1.0mm G300-Z275 Galvanised steel. The Pyrda Mininail is used for simple butt joints of timber of small sized and for application such as in furniture. Pryda Knuckle Nail Plates, Mininails and Strap Nails are manufactured from G300 Z275 ZincForm steel or equivalent.

37 Nail Plates Nail-On Plates Pryda heavy duty pre-punched plates are flat, galvanised or stainless steel plates which are nailfixed to timber to form various types of joints. Their medium to high load capacities and wide range of sizes make them ideally suited for on-site work, including: Joining trusses on-site that have been made in parts in the factory Fixing trusses to poles Any heavy duty timber connection where a Knuckle nailplate will not suffice. Joining beams Repair work over existing fixings

38 Nail Plates Pole Cats Pryda pole cats are anti-split nailplates for timber poles and posts. Available in four sizes, from 150mm to 300mm diameter, most have a central hole to allow pole inspection. They are applied by hammering.

39 Nail Plates Strap Nails A toothed steel nailplate for speedy construction of timber. Pryda Strap Nails are a range of nailplates with prepunched Claw nails at each end. These connectors are: Designed for fast construction jointing of timber frames using a hammer Suitable for all timbers as thje sharp, twisted form of lightest softwoods to the densest hardwoods. Time-saving and, therefore, cost saving. Applications include: Top plate corner connection Intersection of top plates Top plate butt joint Posty and beam connection Bottom plate butt joint Floor bearers at supports Pryda Knuckle Nail Plates, Mininails and Strap Nails are manufactured from G300 Z275 ZincForm steel or equivalent.

40 Brackets Anti-Crush Plate Fascia s Log s Pergola Angles Universal Heavy Duty Angle

41 Brackets Anti Crush Plate Pryda Anti-crush Plates are used to avoid crushing of the timber wall plate at supports of heavily loaded timber trusses. They do this by increasing the width of bearing and, therefore, the bearing capacity. Common applications are where girder trusses are supported on corner wall junctions and on internal supports.

42 Brackets Fascia Suports Special bracket for structural connection of verandas and pergolas to rafters or trusses at the fascia line. Pryda Fascia s are used to connect the overhangs of rafters or trusses to fascias or fascia ledgers so that a veranda or pergola can be adequately supported from the fascia line. Verandas and pergolas usually support only a lightweight roofing or shade cloth, but occasionally they also support or resist: (a) the weight of a worker and materials or tools carried (total design load = 110 kg) (b) forces due to the uplift effect of wind - which can also be the equivalent of hundreds of kilograms, depending on the degree of exposure of the site and roof area supported. By comparison, the design strength of two 2.8 mm nails into green softwood (such as Oregon) is only the equivalent of 44 kg (short term loading). Pryda Fascia s overcome this problem by: providing a strong fascia to rafter or truss connection, designed in accordance with AS Timber Structuresmeeting strength requirements for all common applications being fast and easy to install with five M12 or ½ inch bolts, nuts and washers. Nail holes in the support facilitate preliminary fixing for positioning.

43 Brackets Log Bracket Joins logs and posts quickly and simply without the necessity of checking out. Pryda Log s have the following features and benefits: No checking out of posts is required, resulting in quick and easy installation. Log s are pressed from Galvabond sheet steel which offers high resistance to corrosion. Their robust nature and central rib ensure rigidity once fixed into place. Can be painted, if desired. To install Pergola Angles & Log Brackets use 35 x 3.15mm galvanised Pryda Timber Connector Nails.

44 Brackets Pergola Angles Heavy Duty, multi-purpose building brackets. Mostly used for connecting pergola rafters to support beams. Available in G300 galvanised steel and G316 Stainless Steel. To install Pergola Angles & Log Brackets use 35 x 3.15mm galvanised Pryda Timber Connector Nails.

45 Brackets Universal Heavy Duty Angles Pryda Universal Heavy Duty Angle is a 2.0 mm thick, G300-Z275 galvanised angle for use in a wide range of applications. It is suitable for use as either left or right hand and either vertical or horizontal. Suggested uses include stair or shelf brackets, as well as an internal or external corner support.

46 Fixes Board Fix Foil Fix Pryda Fix Shade Fix

47 Fixes Board Fix Pryda Board Fix is an ideal connector for fixing 10mm Thermawall foil-faced insulation board to timber frames. It is easy and quick to install with in-built teeth that eliminate the need for nails.

48 Fixes Foil Fix Pryda Foil Fix is an ideal connector for fixing building foils to timber framing. Its advantages include: Adaptability: Foil fix can be used to fix foil insulation to both wall and roof frames. Withdrawal Strength: In timbers of joint group JD4 (eg: dry radiata pine) or better, Foil Fix s withdrawal resistance is greater than that of the foil. This is due to the twisted nail profile which allows ready penetration into and excellent holding power in all timbers, from the softest to the hardest. Tear Resistant Design: The special design of Foil Fix includes rounded and coined edges and a wide size (21mm) which greatly reduces the tendency of the foil to tear in windy conditions. Ease of Use: Foil Fix is supplied in easy span-off sticks of 10 for fast, convenient and safe use on-site.

49 Fixes Pryda Fix A non-tear economical fixing for foil insulation and shade cloth. Wall Insulation: Pryda Fix is a simple and economical method of fixing building foil insulation to timber framing. It holds the insulation foil securely and prevents tearing. Recommended fixing spacing is 600 mm. Roof Insulation: Pryda Fix may be used for fixing insulation foil in roof construction. It holds the insulation foil securely and prevents tearing due to the rounded corners of the product. Privacy Screens: Pryda Fix enables quick and efficient installation of netting on privacy screens. Recommended fixing spacing is 400 mm. Shade Cloth: Pryda Fix also facilitates fixing of shade cloth onto timber pergolas or other framework, eliminating the need for battens to hold the shade cloth in position. Recommended fixing spacing is 400 mm. Hot House Covering: Pryda Fix is also suited to fixing sheet p.v.c. onto hot houses for both domestic and commercial use. Pryda Fix prevents tearing of the sheeting.

50 Fixes Shade Fix Pryda Shade Fix has been especially developed for fixing woven and knitted shade cloth to timber framing. The all-new plates feature a rounded coined edge, designed to eliminate tearing on sharp edges by holding the cloth firmly against the timber when pre-punched nails are driven home. Pryda Shade Fix is manufactured in easy snap-off stick form (5 plates, each 50x13 mm) for speed and safety during installation. Pryda Shade Fix is available in either Standard Zinc/Galvanised, Green or Brown Colourbond finish.

51 Builder s Hardware Pryda Truss Spacer Barge Angles Ant Caps, Termite Shields, Edge Pins

52 Builder s Hardware Pryda Truss Spacer Assist with Speeding up Truss Installation, as the Pryda Truss Spacer works as an accurate gauge prior to fixing, including the pre-formed teeth in both ends of the spacer. No need to cut temporary timber bracing. Easy to handle, safe and economical reduce from a two to a one-man installation.

53 Builder s Hardware Barge Angles Prdya External and Internal Barge Angles provide easily installed, low cost and safe backing materials for linings of wall frames at a 45-degree angle junction. Pryda Barge Angles have been designed to provide support for wall linings (such as plasterboard) on internal, angled wall junctions. They replace fillet studs, the cutting of which is costly and dangerous. Specifically, the advantages of Barge Angles are: Quick and easy to install Time and cost savings Safe installation

54 Builder s Hardware Ant Caps Galvanised steel Ant Caps are used to protect buildings against subterranean termites. Termite Shields Galvanised steel Termite Shields are used to protect buildings against subterranean termites. Complies with AS Edge Pins Convenient pins for holding formwork etc. at ground level.

55 Timber Connector Nails For fixing of all Pryda Bracings and some connectors, it is essential to use galvanised Pryda Timber Connector Nails, ie: the special 35x3.15mm nails developed by Pryda specifically for fixing of our products. Laboratory strength testing has shown that clouts are not adequate for this prupose as their heads may pop off under less than design load.

56 Post Anchors Full Stirrup Post Anchor Half Stirrup Post Anchor High Wind Post Anchor Centre Fix Post Anchor Centre Pin (T-Blade) Post Anchor Bolt Down Adjustable Post Anchor, Solid Stem & Fish Tail

57 Post Anchors Full Stirrup Post Anchor Primarily used for bolting to existing concrete. Can also be used for setting to concrete having a maximum clearance. To be installed central to post. Conforms to AS , Protection of Buildings from Termites. All joints are welded. dimensions are: Stem-25mm diameter x 2.0mm thickness, Stirrup thickness = 4mm. Steel G250 AS

58 Post Anchors Half Stirrup Post Anchor Ideally suited to uses where the post is located against a wall or step and can only be bolted from one side. Can be bolted to existing concrete or decking or set into concrete. Recommended maximum post size 90mm. To be installed central to post. Conforms to AS , Protection of Buildings from Termites. All joints are welded. dimensions are: Stem-25mm diameter x 2.0 thickness, Stirrup thickness = 4mm.

59 Post Anchors High Wind Post Anchor Engineered for high wind areas, including tropical regions. The U Shape base is designed for maximum hold-down in concrete. See AS1684:2010 Part 3 Table 9.20 (j) reinforcing rod install over anchor end. To be installed central to post. Conforms to AS , Protection of Buildings from Termites. All joints are welded. Steel G250 AS Hot dipped galvanised 5mm steel.

60 Post Anchors Centre Fix Post Anchor Generally used to hide the post anchor popular with builders for use in outdoor alfresco areas. The post is slotted at the bottom and bolted through the post anchor, leaving only the bolt heads, nuts and washers visible. Can be bolted to existing concrete or set into concrete. Recommended maximum post size 90mm. To be installed central to post. Conform to AS , Protection of Building from Termites. All joints are welded. dimensions are: Stem-25mm diameter x 2.0mm thickness, Stirrup thickness = 4mm. Stee; G250 AS

61 Post Anchors Centre Pin (T-Blade) Post Anchor For use where the post anchor is NOT to be visible popular with builders for use in outdoor alfresco areas. Due to the fixing method, it is only suitable for small spans or where no roofing is used. Recommended maximum post size not to exceed 125mm. To be installed central to post. Conform to AS , Protection of Buildings from Termites. All joints are welded. dimensions are: Stem-25mm diameter x 2.0mm thickness, Stirrup thickness = 4mm.

62 Post Anchors Bolt Down With knockout 3mm adjustable washer to facilitate adjustment after bolt holes have been drilled. Used for locating posts onto existing concrete or decking. To be installed central to post. Galvabond and Hot Dipped Galvanised 2mm Stirrup and 3mm Base.

63 Post Anchors Adjustable Post Anchor Convenient and fully adjustable for any practical post size. No checking of the post is required. Not recommended for post greater than 125mm x 125mm. To be installed central to post. Confirm to AS , protection from termites. All joints are welded Steel G250 AS Solid Stem A full stirrup post anchor with a solid angle stem, suitable for setting into wet concrete. Fish Tail A centre fix design post anchor that is designed with an angled stem for setting directly into wet concrete.

64 Bunnings welcome the opportunity to quote your next job. Please contact your local Bunnings Account Manager or call