2. Connect driver to power source leads. After connections are made, place driver above ceiling. SEE MINIMUM SPACE REQUIREMENTS BELOW.
|
|
- Edgar Crawford
- 5 years ago
- Views:
Transcription
1 INSTALLATION INSTRUCTIONS INSTALLATION: 1. Cut proper opening in ceiling. Round: 140mm Ø, Square: 140mm x 140mm 140mm Ø 140mm x 140mm 2. Connect driver to power source leads. After connections are made, place driver above ceiling. SEE MINIMUM SPACE REQUIREMENTS BELOW. MINIMUM SPACE REQUIREMENTS 230mm 180mm
2 INSTALLATION INSTRUCTIONS 3. Make electrical connection 4. Note: Fixture can be installed fully assembled as shown. Aim the fixture vertically to the 0 degree position as shown. 5. Using finger pressure, push the mounting springs against the fixture body and raise the fixture into the cutout. Release the springs when the fixture is at a level where it can be pushed up flush to the ceiling from below. Fig. 1
3 AIMING INSTRUCTIONS HORIZONTAL AIMING : 1. Loosen rotation lock screw through aperture (no tool required). 2. Turn to desired horizontal aiming position. 3. This trim has a rotation stop, if further rotation is not possible, reverse direction. 4. Tighten lock screw once in desired position. Rotation Lock Screw Rotation Stop VERTICAL AIMING 0-35 : 1. Loosen rotation lock screw through aperture (no tool required). 2. Tilt to desired vertical aiming position. 3. Use the tilt angle indicators as a reference. 4. Tighten lock screw once in desired position. Vertical Tilt Lock Screw Tilt Angle Indicators
4 SERVICE AND FIXTURE REMOVAL ROUND TRIM ACCESSORY HOLDER / SNOOT HEATSINK SPRING (2) 35 TILT VERTICAL SERVICE ACCESS AND FIXTURE REMOVAL: 1. Remove trim lens assembly from the fixture by raising the hinged lens upward enough to allow access to insert fingers to pull the edge of the trim downward. 2. Remove the reflector from the fixture by rotating it approximately 5 degrees counter clockwise. SPRING 3. Remove the snoot/accessory holder from the fixture by reaching through the aperture and compressing the springs as shown. Remove snoot from trim. REFLECTOR 4. Reach up through the aperture and locate the tips of the two mounting springs. 5. Apply pressure to the spring tips and pushing them towards the fixture body, allowing the fixture to start to come out through the opening. Working from below also, apply downward pressure on the fixture flange to finalize removal. TRIM LENS ASSEMBLY
5 SERVICE AND FIXTURE REMOVAL SQUARE TRIM ACCESSORY HOLDER / SNOOT HEATSINK SPRING (2) 35 TILT VERTICAL SERVICE ACCESS AND FIXTURE REMOVAL: 1. Remove trim lens assembly from the fixture by raising the hinged lens upward enough to allow access to insert fingers to pull the edge of the trim downward. 2. Remove the reflector from the fixture by rotating it approximately 5 degrees counter clockwise. SPRING 3. Remove the snoot/accessory holder from the fixture by reaching through the aperture and compressing the springs as shown. Remove snoot from trim. REFLECTOR 4. Reach up through the aperture and locate the tips of the two mounting springs. 5. Apply pressure to the spring tips and pushing them towards the fixture body, allowing the fixture to start to come out through the opening. Working from below also, apply downward pressure on the fixture flange to finalize removal. TRIM LENS ASSEMBLY
INSTALLATION INSTRUCTION Silo Multiples - New Construction Housing MT-4*15, MT-4*10
IMPORTANT SAFETY INSTRUCTIONS 1. Read all instructions before installing. 2. System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
More informationDOWNLIGHT LED SERIES INSTALLATION INSTRUCTIONS
WARNING: This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Make sure all
More informationEXPLODED VIEW AND PART CALL OUT ASSEMBLING THE METALUX DF SERIES FRAME KIT
EXPLODED VIEW AND PART CALL OUT CUTOUT DIMENSIONS ON PAGE 2 CEILING BRACING (BY OTHERS) SHEET ROCK METALUX DF SERIES FRAME KIT S282 (2'X2') FIXTURE SHOWN FIXTURE SIZE FRAME KIT PART # 2' X 2' DF-22W-U
More informationCOWO. Customer Wall Outlet. 1 General. 2 Kit content. 3 Handling of the box. TC-1203-IP Rev A, Apr
COWO I N S T A L L A T I O N I N S T R U C T I O N TC-1203-IP Rev A, Apr 2017 www.commscope.com Customer Wall Outlet 1 General Customer Wall Outlet 2 Fiber for max. 2 bend reduced fibers, 2 SC-adapters
More informationL182 - Installation Sheet Modular Wine Rack ( Wall Mount )
Modular Wine Rack ( Wall Mount ) 1A 1B 2B 2A Cross Bar Options: 1A 2A 1B 2B Modular Wine Rack ( Wall Mount ) Parts Rail LED arm modules Wine bottle cross bars Rail cover Setscrew cover 1) Drill holes and
More information- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS. Factory pre-installed mud flange TOOLS REQUIRED: Phillips screwdriver, 5/16 nut driver.
- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS TruGroove Drywall A3 MOUNTING Ceiling INSTALLATION System Overview These instructions review how to install drywall trim versions of TruGroove recessed
More informationInstall the Housing. Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing EN3_-LH9_ 1.
Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing 90ENTRA EN_-LH9_. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is safety
More informationInstallation Instructions Standalone or continuous run configurations - 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS
- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS TruGroove Drywall A3 MOUNTING Ceiling INSTALLATION System Overview These instructions review how to install trimless drywall versions of TruGroove
More informationDiptych Bath Screen Installation Guide
v1 These instructions are for left and right handed screens. The diagrams show a right handed screen. Page i Thank you for purchasing this Diptych Bath Screen. Please study these instructions carefully
More informationTHIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
LumeLEX 2026 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationRAIL 4 INSTALLATION INSTRUCTIONS. RM4DOD Recessed GENERAL SAFETY INSTRUCTIONS: NOTE:
INSTALLATION INSTRUCTIONS RAIL 4 RM4DOD Recessed NOTE: The following instructions provide general guidelines for product installation. For additional information consult the applicable electrical codes
More informationThis product is designed for a water supply pressure range of 20 psi (137kPa) minimum to 80psi (550 kpa) maximum.
We appreciate your commitment to Kohler quality. Please take a few minutes to review this manual before you start installation. If you encounter any installation or performance problems, please don t hesitate
More informationHigh Rise Sit-Stand Desk Converter
High Rise Sit-Stand Desk Converter Assembly Instructions for Model DC350 Patent No. 9,332,839 PRE-ASSEMBLY Please read all instructions before beginning assembly. We strongly recommend you watch the video
More informationINSTALLATION INSTRUCTIONS FOR FLUSH MOUNT FIXTURES
Kurt Versen Company Point Source Lighting Models with Round Apertures 10 Charles Street Westwood, New Jersey 1 PLEASE READ THIS ENTIRE INSTRUCTION SHEET BEFORE INSTALLATION. 2 DISCONNECT ELECTRICAL POWER
More information* * 98/9950WDC. Fire-Rated Devices include these. additional components. 1-Point Latch (LBL)
*24739468* 24739468 98/9950WDC Installation Instructions 1-Point Latch (LBL) Fire-Rated Devices include these additional components Metal Edge Wrap required for 60 and 90-minute applications 2-Point Latch
More informationAUC Cell Assembly Torque Stand. User Manual
AUC Cell Assembly Torque Stand User Manual WARRANTY Spin Analytical Inc., warrants this product to be defect free in both material and workmanship for 90 days from the date of shipment. Labor services
More informationSmartView Mounting Frame 3 Wide x 3 Deep Video Wall Display Installation Guide
SmartView Mounting Frame 3 Wide x 3 Deep Video Wall Display Installation Guide WMK-034 This display kit mounts ViewSonic 46 Video Wall displays in a 3 wide by 3 deep landscape configuration. The frame
More informationJoiner Kit Joiner bracket (x1) Biscuit aligners (x2) Trim Flange
- Trim System Overview These instructions review how to install TruGroove Perimeter fixtures. Modules can be installed as individual standalone units, or they can be joined together to create continuous
More informationMultiples EM_ 1.4. Install 1X1/1X2/1X3/1X4 Housings. Installation Instructions for. This product is suitable for indoor locations.
Installation Instructions for 90EMULTI Multiples EM_. GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations. This product can be dimmed with a standard electronic dimmer or a 0-0V
More informationNETpodium Rack ( & ) INSTRUCTION SHEET Jan 2017 Rev B
(1-1671405-1 & 1-1671405-2) 411-117000 Jan 2017 Rev B 1-1671405-2 1-1671405-1 1. Kit Content Bottom Frame Assembly Top Frame Assembly Carboard Stencil Vertical Profile Assembly Wire Basket Bracket Wire
More informationINSTALLATION INSTRUCTIONS FOR FLUSH MOUNT FIXTURES
Kurt Versen Company Point Source Lighting 10 Charles Street Westwood, New Jersey Models with Square or Rectangular Apertures 1 PLEASE READ THIS ENTIRE INSTRUCTION SHEET BEFORE INSTALLATION. 2 DISCONNECT
More informationElectron Microscopy Sciences
Electron Microscopy Sciences INSTRUCTIONAL MANUAL CAT. #7670 FlipScribe P.O. Box 550 s1560 Industry Road s Hatfield PA 19440 1 Overview The FlipScribe enables cleaving through frontside targets with a
More informationHigh Rise Sit-Stand Desk Converter
High Rise Sit-Stand Desk Converter Assembly Instructions for Model DC300 Patent Pending PRE-ASSEMBLY Please read all instructions before beginning assembly. We strongly recommend you watch the video at
More informationMounting a BalanceBox 400 to a brick wall
Unpack the BalanceBox 400 and remove the Wall frame cover and its bag of screws. Slide the cover out at the top. NOTE: the cover is NOT included with the BalanceBox 400H LOCK SCREW HOLE MOBILE STAND MOUNTING
More information1 Removing The Screen Track, Screen and Screen Rollers Note: The screen remains in the track while the track is removed and/or installed.
Sliding Door Screen and Screen Track Replacement Service Instruction These instructions apply to: Architect Series 12/2004-Current Designer Series 3/2005-Current Tools Required: #2 Phillips head screwdriver
More informationINSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE
T F W 604.549.979 604.549.9555 fluxwerx.com INSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE fixture housing endcap kit optic kit join kit notch 2 cross section notch 4 cross section 4 4" 4-11/2" 4 /8 (111)
More informationLF Series Assembly Instructions
LF Series Assembly Instructions 1998760 Revision A-10 Complete Series Master Packet 2010 Kimball International, Inc. T 800.482.1818 F 812.482.8300 Footprint Storage and Metal Filing Systems Assembly Instructions
More information7878 K940. Checkpoint Antenna. Kit Instructions. Issue B
7878 K940 Checkpoint Antenna Kit Instructions Issue B Revision Record Issue Date Remarks A July 7, 2009 First issue B Nov2013 Revised the Checkpoint installation procedures for 7878 and 7874 scanners Added
More informationRepairing Microsoft Wedge Touch Mouse Battery Cover Retaining Clip
Repairing Microsoft Wedge Touch Mouse Battery Cover Retaining Clip Disassembly, repair and reassembly of Wedge Touch mouse when the battery cover will not stay closed. Also is a good guide to repair other
More informationRound or Square Type IC Wall Wash Housing with Lamp for Flangeless Trims
Installation Instructions for 90ELED-WIC Round or Square Type IC Wall Wash Housing with Lamp for Flangeless Trims LED E_L_-L_WI. LED - ROUND/ SQUARE FLANGELESS GENERAL PRODUCT I NFORMATION: This product
More informationRH-412 STEEL DOORS INSTALLATION INSTRUCTIONS
RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.
More informationSTEINBERGER TRANSTREM (TYPE 2) TECHNICAL DOCUMENT
STEINBERGER TRANSTREM (TYPE 2) TECHNICAL DOCUMENT These instructions apply to newer style TransTrems only (non-threaded ball type or modified threaded ball type). For purposes of discussion, these TransTrems
More informationINSTALLATION INSTRUCTIONS RH 412 STEEL DOORS
By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side. Note: Having the hood open makes the job
More information3 wide x 3 deep Video Wall Display Installation Guide
HoverTrack Series 3 wide x 3 deep Video Wall Display Installation Guide VWD-3X3-X462 This display kit mounts NEC X461UN and X462UNS LCD monitors in a 3 wide by 3 deep landscape configuration. The frame
More informationS-85SCH
4411-4423-4432-4443-4452 5511-5523-5532-5554 44S-85SCH Service Manual 104 73 14-26 2014-02-24 CONTENTS 1. Names of principal parts...2 2. Removing methods of external parts 2-1 Sewing table...3 2-2 Face
More informationIntroduction: The T30069 Center Punch Tool installs BAND-IT 3/8" and 5/8", 201 Stainless Steel and Galvanized Carbon Steel clamps.
Instruction Manual Introduction: The Center Punch Tool installs BAND-IT 3/8" and 5/8", 201 Stainless Steel and Galvanized Carbon Steel clamps. Table of Contents: 1. Introduction & Safety Practices 2. Operating
More informationLumber Smith. Assembly Manual. If you are having problems assembling the saw and need assistance, please contact us at:
Lumber Smith Assembly Manual If you are having problems assembling the saw and need assistance, please contact us at: 804-577-7398 info@lumbersmith.com 1 Step 1 Safety Carefully read the Owners Manual.
More informationIntroduction: The T30069 Center Punch Tool installs BAND-IT 3/8" and 5/8", 201 Stainless Steel and Galvanized Carbon Steel clamps.
Instruction Manual Introduction: The Center Punch Tool installs BAND-IT 3/8" and 5/8", 201 Stainless Steel and Galvanized Carbon Steel clamps. Table of Contents: 1. Introduction & Safety Practices 2. Operating
More informationAssembly Instructions
1 27694 Trend Podium Assembly Instructions #27694 Trend Podium Part Drawing Description Qty Part Drawing Description Qty P-1 Base 1 EA Hardware List Screw M6x12mm 30 EA P-2 Right Side Panel 1 EA A2 Phil
More informationINSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE:
INSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE: 268 June 22, 2010 TOOLS NEEDED COMPONENTS INCLUDED P2 Tip 3/8" Drill Rubber Gasket(s) x 2 Bracket(s) x 2 1/2" Drill Bit Bulkhead Flange #2 Phillips
More informationInstallation Instructions For Aurora Dual MR16 Round & Square Edge 3.3" Fig.1 Complete Fixture ADJUSTABLE GEARS HIDDEN BEHIND THE LAMP PAN LOCK
2015 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Dual MR16 Round & Square Edge 3.3" 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.purelighting.com
More informationHollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide
Hollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide Tools Required: two adjustable wrenches, pliers, ¾ socket wrench recommended Note: please do assembly near your vehicle as you Can
More informationBand-Master ATS Nano Pneumatic Banding Tool Operating Instructions
Band-Master ATS 601-118 Nano Pneumatic Banding Tool CONTENTS 601-118 Overview... 3 Safety.... 5 Initial Tool Set-up... 5 Regulator assembly mounting... 5 Attach tool head to regulator.... 6 Operating instructions...
More informationTOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR FORD FLARESIDE TRUCKS
TOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR 53-87 FORD FLARESIDE TRUCKS Vise Grip Clamps C-clamps Sharpie Marker Ball Peen Hammer Center Punch 3/8 or 1/2 Drill 5/32, 7/32, 9/32, and 3/8 Drill Bits
More informationShetland Stalls Installation Instructions
Shetland Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 1/9/18 Before you start Kit can accommodate up to 12 wide stall front
More informationAG19 10 OC Cantilever. Assembly and Operation Guide
AG19 10 OC Cantilever Assembly and Operation Guide Thank you for your purchase of Treasure Garden s AG19 Cantilever Umbrella. Please remove all contents from the package, inspect and review checklist.
More informationTRUE TECHNICAL SERVICE MANUAL - ALL MODELS. DOORS/DRAWERS/LIDS
DOORS/DRAWERS/LIDS 55 56 NOTES DOORS/DRAWERS/LIDS Springs 97 TORSION SPRING REPLACEMENT GDM RADIUS FRONT - SWING DOOR INSTALLATION INSTRUCTIONS Tools Required (2) - 1 8" drift Punch (forged) Needle-Nose
More information20 Memory Drawers. Copyright 2002 IPP Design Competition All rights reserved. Puzzle Solution:
20 Memory Drawers This work memorizes 120 (The factorial of 5) kinds of turn to open the drawers. The big base is full of 30 device plates. The plates move vertically and horizontally, and change the arrangements
More informationGreenslade & Company, Inc. USA
Greenslade Recess TIR Gaging System Patent # 5,182,865 Gage Application: The Recess TIR Gage is designed to make the measurement of the concentricity of the screw s drive system and head O.D. to its shank
More informationLightplane 3.5 Recessed
INSTALLATION INSTRUCTIONS Lightplane 3.5 Recessed LP3.5R Recessed Ceiling IMPORTANT SAFETY INSTRUCTIONS When installing or using this fixtures basic safety precautions must be followed. Read all instructions
More informationEasy Step by Step Manual
Easy Step by Step Manual Teletower Mini XL Wall-Floor installation The tower packages #1-#2-#3 Open Base Package #1 for the main tower parts. Here you see the three tower tubes (H-Head, M-Middle, F-Feed)
More information45 CUTTING HEAD TILE SAW-BLADE ALIGNMENT PROCEDURE
The of the MK-770 may become misaligned with the Cutting Head of the Tile Saw over time. Should misalignment occur, perform the following steps to realign the Tile Saw. NOTE: If alignment problems are
More informationReplacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C)
Follow the instructions below to replace the reciprocator in the SWF Compact series machines. The tools required can be found in the tool kit that came with the machine. Preparation 1. First, place the
More informationEXIT DEVICE OPERATION FIRE DOOR LABELS, STRIKES AND FRAME SCREWS FOR INFORMATION CALL OR VISIT RITEDOOR.COM
RECORD & LABELS WHAT THIS OWNER'S CAN DO FOR YOU It explains exactly how The Rite Door operates. It explains periodic maintenance requirements necessary to assure reliable operation. It explains simple
More informationAssembly Instructions. Important!
Play Action Spiral Tube Slide Assembly Instructions Important! Intended for residential use by children ages 2 to 10, only on properly installed PlayStar playsets. Before use refer to complete safety guidelines
More informationLCD/Plasma Mount Manual
LCD/Plasma Mount Manual Product Overview: Thank you for your Cheetah Mount purchase. All Cheetah Mounts are designed to provide excellent function, high quality, easy installation and stylish appearance.
More informationModular Drawer & Door Systems Installation Instructions Locking Drawers and Receding Doors
Modular Drawer & Door Systems Installation Instructions ocking Drawers and Receding Doors Pre-Installation Before you begin installation: 1. Read through the installation procedure before starting the
More informationPULL-THRU USER S MANUAL
PULL-THRU USER S MANUAL G14x Part # 310 120 177 G20 Part # 310 120 188 G20x Part # 310 120 186 G40x Part # 310 120 163 TABLE OF CONTENTS SECTION 1 PCB DESIGN AND MOUNTING SECTION 2 MOUNTING ADAPTER TO
More informationKai Installation Instructions
Kai Installation Instructions Before Beginning Installation Read through the entire instruction thoroughly A minimum of 2 people are required for this assembly These instructions reflect typical assemblies;
More information1.1.1 The cube assembly has two filter retainer rings; one is located on the Exciter side and one is on the Emitter side as shown below.
1.1 Disassemble Cube 1.1.1 The cube assembly has two filter retainer rings; one is located on the Exciter side and one is on the Emitter side as shown below. Emitter Retaining Ring Exciter Retaining Ring
More informationAssembly & Disassembly Guide
Carvable Jaw Block Assembly & Disassembly Guide quincy\prod. Setup info\jawkits\jawkit setup guide P/N CARV-95, REV C 02/18/03 Index: Page Revision History... 1 Sec. Carvlock/ Fixture Vise 1.0 Jaw Block
More informationSentinel Series Cigar Humidor End Tables
Sentinel Series Cigar Humidor End Tables Assembly Instructions Models: Sentinel 500, 1000 and 1500 Style: Traditional SENTINEL ASSEMBLY INSTRUCTIONS Congratulations! You have purchased a superior cigar
More informationReplacing the Reciprocator on an SWF Multi-head.
Replacing the Reciprocator on an SWF Multi-head. Follow the instructions below to replace the reciprocator in the SWF multi-head machines. The tools required are found in the tool kit that came with the
More informationTilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM
Tilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM Easy installation Built-in level for easy positioning Corrective leveling adjustments after installation Forward /
More informationInstallation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH1-ARE, AH1-ARB, AH1-ASE, AH1-ASB. Fig.
2015 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH1-ARE, AH1-ARB, AH1-ASE, AH1-ASB 1718 W. Fullerton Ave Chicago, IL 60614
More informationGP-SD GENIE PROBE SMALL DIAMETER
For GENIE PROBE SMALL DIAMETER Installation and Operation Instructions 2 for s Locking Mechanism (if supplied) Set Screws Backed Out To ensure that the is Locking never accidentally loosened or Mechanism
More informationSport-Thieme Safety Aluminium Mini Training Goal
Assembly instructions Art.-Nr.: 116 3852 Sport-Thieme Safety Aluminium Mini Training Goal 0218214 2018 Sport-Thieme GmbH D-38367 Grasleben Germany sport-thieme.com info @sport-thieme.com Phone: +49 53
More information4 BAY Low Profile WALL MOUNT CABINET
D1/347 SSEMLY INSTRUCTIONS 4 Y Low Profile WLL MOUNT CINET TIP HZRD WRNING! Cabinet must be affixed to wall. For use to prevent tipping in compliance with capacity of cabinet specified. Use with heavier
More informationMK-7 Maintenance Manual Revision3 (Ver R02)
MK-7 Maintenance Manual Revision3 () 1. Features ------------------------------------------------------------------------------------ P2 2. Components -------------------------------------------------------------------------------
More informationVhu. Universal Boring Heads Vhu 2 1/8, 3 1/8, 4 7/8, 6 ¼. Vhu. Instruction Manual No.:
Instruction Manual No.: 2420304 Vhu Vhu Universal Boring Heads Vhu 2 1/8, 3 1/8, 4 7/8, 6 ¼ Producer: Moskevska 63 101 00 Praha 10 Vrsovice Czech Republic Phone: +420 246 002 249 Fax: +420 246 002 335
More informationSport-Thieme Safety Aluminium Mini Training Goal
Assembly instructions Art.-Nr.: 116 3881 Sport-Thieme Safety Aluminium Mini Training Goal 0218214 2018 Sport-Thieme GmbH D-38367 Grasleben Germany sport-thieme.com info @sport-thieme.com Phone: +49 53
More informationFour-Thread Safety Stitch
Four-Thread Safety Stitch Four-Thread Safety Stitch This stitch is an alternative to the Five-Thread Safety Stitch. It offers the same type of Two-Thread Chainstitch. However the Three-Thread Overlock
More informationSit Down Table Assembly Instructions
Sit Down Table Assembly Instructions Parts that come with your sit down table A B C D E F G H I J K L M N Extension leaf Table with cutout for machine Two table legs One table leg with long support One
More informationD3976 RECESSED EXIT INSTALLATION INSTRUCTIONS
PACKAGE CONTENTS PRODUCT MUST BE INSTALLED ACCORDING TO ALL APPLICABLE BUILDING AND LIFE SAFETY CODES TEMPLATE INSTALLATION INSTRUCTIONS STRIKE HAND TOOL 5/32 HEX KEY ROD END CAPS EXIT DEVICE CRANK ARM
More informationNORMAN SHUTTERS INSTALLATION INSTRUCTIONS. 4 Sided L Frame. (Outside Mount - Single Panel) Getting Started
NORMAN SHUTTERS INSTALLATION INSTRUCTIONS 4 Sided L Frame (Outside Mount - Single Panel) Getting Started Recommended Tools: Nail Gun or Drill, Tape Measure, Torpedo Level, Box Knife, 6 Philips head driver
More informationJUMBO STENCIL CUTTING MACHINE PARTS LIST AND OPERATING MANUAL
JUMBO STENCIL CUTTING MACHINE PARTS LIST AND OPERATING MANUAL Marion, IL USA STK. NO. 5800-152, REV A Warning: This machine contains pinch points which can injure personnel when not used properly. This
More informationCapri. I n s t r u c t i o n M a n u a l. Balcony Umbrella x 6.93 Rectangle / SSBU-5X7RT5T
Capri Balcony Umbrella 4.95 x 6.93 Rectangle / SSBU-5X7RT5T I n s t r u c t i o n M a n u a l Thank you for your purchase of SimplyShade s Capri Balcony Umbrella. Please remove all contents from the package,
More informationOPERATING INSTRUCTIONS FOR MODEL SPR-25 Manual Stencil Printer
OPERATING INSTRUCTIONS FOR MODEL SPR-25 Manual Stencil Printer TABLE OF CONTENTS I. INSTALLATION...3 II. SET-UP...4 III. Z AXIS ADJUSTMENT (Screen Height)...6 IV. X, Y AND Ø ADJUSTMENTS...6 V. SQUEEGEE
More informationInstruction Sheet P/N B Trim the new RTD wires. 5. Coat the new RTD with. 4. Strip the ends of the existing
Instruction Sheet P/N 1029716B 02 RTD Service Kit - P/N 1028320 02/08 Use this service kit to replace either the tank or the manifold RTD on any ProBluet or Mesat adhesive melter. If you are replacing
More informationConnect each sections electricity cables with a connections block or splices and heatshrink. Proceed to Myla installation manual.
MYLA L & XL ASSEMBLY 1. 2. PARTS 3-5 SECTIONS Prepare a soft clean workspace to assemble the light fixture. Carefully unpack the light fixture and other contents. Myla L consists of 3 separate sections
More informationInstallation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH2-ARE3 & AH2-ASE3. Fig.1 Complete Fixture
015 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH-ARE3 & AH-ASE3 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195
More informationOVERVIEW. Mounting Post (2 places) Cylinder Cam. Handing Pin
DEVICES COVERED IN THIS DOCUMENT: 46CE Cylinder Escutcheon Key locks and 46DT Dummy Trim Pull when dogged unlocks lever 46BE Blank Escutcheon Always operable 46NL Night Latch Key retracts latchbolt 46NK
More informationInstallation Instructions
1. Do not touch while lamp is on. Turn off/unplug and allow to cool 9. Do not install within 10 feet of a pool, spa, or fountain. before replacing lamp. 10. Have installed in accordance with all applicable
More informationMM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM30 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationINSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET
HIGH EDGE 2 1/4"(57mm) 03079400070 INSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET IMPORTANT: THIS LOCK IS NON-HANDED. LOCK IS FACTORY PACKED PREADJUSTED FOR 1³ ₄" (45mm)
More informationInstallation Instructions for. Before You Begin TOOLS REQUIRED
Composite Railing System STEP-BY-STEP Installation Instructions for Spectrum Composite Railing Virtually maintenance free 20-year warranty EverNew Spectrum Railing system is designed to work with a number
More informationMAIN PARTS
MAIN PARTS 7 8 9 10 11 12 13 1 2 3 17 4 5 6 01 02 03 04 05 12 23 34 45 56 13 24 35 46 57 14 25 36 47 58 15 16 26 27 37 38 48 49 59 60 06 07 08 09 10 17 18 28 29 39 40 50 51 61 62 19 30 41 52 63 20 21 31
More informationSERIES. Installation Instructions
7 1 0 4 SERIES Installation Instructions Important: Please keep these instructions. The combination of this lock has been factory preset: 2 and 4 pressed together, then 3. WARNING For your own safety,
More informationRequired Tools: Suggested Additional Tools: 1 Cordless Drill with Robertson Bits 1 Ratchet Wrench 1 7/16 or 11mm socket 1 7/16 or 11mm Gear Wrench
Thank you for your recent purchase of a Cabinets by Hayley garage cabinet system. You are about to experience the best made cabinets that you can purchase. Cabinets by Hayley are designed for beauty and
More information* * 9875/ Customer Service #10-24 # Dogging Key (use to lock down pushbar)
*911374-00* 911374-00 Mortise Exit Device 9875/9975 Installation Instructions #10-24 #12-24 Dogging Key (use to lock down pushar) Customer Service 1-877-671-7011 www.allegion.com/us Allegion 2015 Printed
More informationOPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS Rotary Microtome CUT 4062 / CUT 5062 / CUT 6062 CUT 6062 illustrated above INS1000GB 2012-01-06 Instructions CUT4062 / CUT 5062 / CUT 6062 2 CONTENTS 1. INTENDED USE... 4 2. SYMBOLS...
More informationInstallation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH2-ARE3 & AH2-ASE3. Fig.1 Complete Fixture
015 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH-ARE3 & AH-ASE3 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195
More informationDoor window. Front door window, assembly overview
64-50 Door window Front door window, assembly overview 1 - Window channel Pushed onto flange 2 - Door window Removing Page 64-52 Adjusting Page 64-53 3 - Door 4 - Outer window channel Pushed onto flange
More informationMM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationGATE INSTALLATION INSTRUCTIONS
GATE INSTALLATION INSTRUCTIONS 1) Ensure posts for gate are fully installed. Posts need to be securely fastened to decking or concrete such that they will not sag with weight of the gate. For a single
More informationVERTEX FASTENERS PANELTACKER. Serial #
VERTEX FASTENERS PANELTACKER www.vertexfasteners.com Model # Serial # 1 Table of Contents Description of Equipment 2 Operation Instruction..3 Maintenance..5 Recommended Spare Parts List.6 Troubleshooting
More informationStorage Cabinet (Model No )
ASSEMBLY INSTRUCTIONS (36" W X 18" D X 72" H) (pg 1 of 10) PARTS LIST (pg 2 of 10) Please check the parts carefully according to the parts list. If you are missing any parts, please contact our customer
More informationInstallers guide Deadbolt 02.
Installers guide Deadbolt 02. version 0.7.1 Specifications Model igloohome Smart Deadbolt 02 Material Zinc Alloy Current Rating (Standby) ~30uA Current Rating (Active) ~200mA Batteries 4 x AA Alkaline
More informationINSIDE PANEL NOT SHOWN TO DETAIL ANCHORING SYSTEM
SIX INCH ALPHA MODULE INSTALLATION KEWAUNEE SCIENTIFIC CORPORATION SIX INCH ALPHA MODULE ANCHORING SYSTEM After Alpha module has been set in desired location. Adjust the four adjustment bolts until the
More informationWooden Frame Type Instruction Manual
Wooden Frame TypeInstruction Manual Thank you for selecting our product. Before starting installation, please read this manual thoroughly to ensure correct installation. Please keep this manual at hand
More information