MORTISE LOCKS LA1Tx7 //DATASHEET

Transcription

1 //DATASHEET SATO ocks AElement Access control requires a good, reliable door locking system. SATO offers a wide range of mortise locks in order to ensure that the door is correctly locked. Whether you need ANSI mortise locks, Euro locks for wooden doors or narrow profiles, DIN locks, Scandinavian standard locks, cylindrical cartridge latches or automatic locks with privacy and panic functions, SATO has the locking system you need. MORTISE OCKS A1Tx7 Publications of SATO SYSTEMS S.. are protected by copyright and all rights are reserved. SATO SYSTEMS publications may not be reproduced in any form or by any means without written permission from the copyright owner.

2 SATO OCKS TUBUAR ATCH - The XS4 ANSI mortise lock is specially designed for doors that need an ANSI mortise lock ANSI in line with an A Grade 1 mortise lock. This lock is easy to install, provides security and is robust. MODE A1T17 MAIN CHARACTERISTICS: atch operation on levers on both sides External handle blocking ever retracts deadbolt and latch simultaneously Auxiliary latch (anticard) deadlocks latch and deadbolt Reversible latch and blocking Handle and privacy detector Door and override detector (depending on the model) Override retracts latch and deadbolt Stainless steel with anti-friction latch 3/4 throw MODE A1T07 MAIN CHARACTERISTICS: atch operation on levers on both sides External handle blocking Auxiliary latch deadlocks latch Reversible latch and blocking Handle and privacy detector Door and override detector (depending on the model) Override retracts latch

3 MECHANICA FEATURES ock case made of stamped steel Finishes available: Satin Stainless Steel or Polished Brass Faceplate: adjustable level 8mm (5/16 ) square split spindle Strike: reversible atch: reversible Fire resistant U isted 90 minuts In line with ANSI/BHMA A Grade 1 compliant for heavy commercial, institutional and industrial use ANSI MORTISE OCK WITH DEADBOT 1-1/16" ( 26,5 ) 4-3/8" (110) Deadbolt Anti-Friction atch 1-5/8" ( 41,2 ) 6-1/8" ( 156 ) 8" ( 203 ) Standard Strike and dust box included Auxiliary atch (anticard) atch 3/4" ( 19 ) 2-3/4" ( 70 ) 27/64" ( 10,7 ) q 5/16" ( 8 ) 1-1/2" ( 38,1 ) Ax 1-1/4" (32) ANSI MORTISE OCK (NO DEADBOT) 4-3/8" (110) Anti-Friction atch Auxiliary atch (anticard) atch 3/4" ( 19 ) 2-3/4" ( 70 ) 27/64" ( 10,7 ) q 5/16" ( 8 ) 1-1/2" ( 38,1 ) 1-5/8" ( 41,2 ) 6-1/8" ( 156 ) Ax 8" ( 203 ) Standard Strike and dust box included 1-1/4" (32) Datasheet-A1Tx-ENG-05-15

4 HANDING CODE Right Hand (RH) Inward opening Inside eft Hand (H) Inward opening Outside Inside Outside Right Hand Reverse (RR) Outward opening RH eft Hand Reverse (R) Outward opening H RR R

5 ATCHBOT POSITION CHANGE ATCHBOT POSITION CHANGING 3/32" or Torx Remove special screw with allen wrench 2. Pull latch bolt out of lock Make sure foot is under latch surface Cannot put in lock with foot above latch surface 3. Rotate latch bolt 180º and reinstall into lock, pushing the latch bolt into the lock and then releasing 4. From oposite side, insert the special screw and tighten securely with the allen wrench. OCKING SIDE POSITION CHANGE OCKING SIDE POSITION CHANGING 1. Remove 2 screws as shown above Dimension in inches (dimension in millimetres) All contents current at time of publication. SATO Systems S.. reserves the right to change availability of any item in this catalogue, its design, construction, and/or materials. 2. Turn lock over opposite side and reinstall screws as shown above. To ensure locking slide does not bind, manually push to the desired side or alternate tightening each screw every 2-3 turns.

6 OCK INSTAATION PREPARING THE DOOR 1. Draw a horizontal line on edge of the door and on inside at the desired height of knob above floor. 2. Draw a vertical centre line on door edge. 3. Draw a vertical line on inside at the proper backset to align the template. 4. Position template on edge of door. Mark ONY top and bottom holes of mortise cavity (A) and lock front on door edge. Remove template: Place lock face against door edge. Trace outline of faceplate as guide for faceplate routing. 5. Mortise door for lock body and faceplate as per instructions on template 6. Position template on inside of door. Mark holes in the lateral face of the door for turnpiece (B) and handles (C and D). Mark the corresponding holes for the electronic escutcheon fixings (E and F). The (F) hole doesn t have to be through, its depth has to be ¾ longer than the lock center. INSTAING THE OCK BODY 1. Insert wires through (F) hole. 2. Insert the lock into the cavity. 3. Mark & drill faceplate holes. Fasten with faceplate screws to hold lock in place. INSTAING THE STRIKE 1. Center strike to lock s frontplate center lane. Refer to latch to determine strike location on jamb. 2. Using strike as template, mark and chisel recess. Drill holes for dust box. Place dust box and strike and fasten screws. Please check that: - Deadbolt and latch fit the cavities of the strike without touching it. - Gap between door and jamb is 1/8.. (A) C EVER C FRONTPATE (A) (D) (D) C (E) (E) (F) (B) BACKSET (C) C EVER HEIGHT ABOVE FOOR Datasheet-A1Tx7-ENG-05-15