INSTALLATION INSTRUCTIONS Z7800 SERIES MORTISE LOCK
|
|
- Theodora Gray
- 5 years ago
- Views:
Transcription
1 801 Avenida Acaso, Camarillo, Ca (805) A. Door Preparation: INSTALLATION INSTRUCTIONS Z7800 SERIES MORTISE LOCK 1. Measure desired height from finished floor, mark a horizontal line on door and door edge. 2. Align template on edge of door with applicable horizontal at height line. Check the chart for drilling trim holes on template and mark only holes for lock function being installed. C L of door edge Height line C L of lever or knob Installation template C L C L C L of cylinder of lockcase of lever or knob Vertical centerline 3. Mortise door edge according to measurements on installation template and drill proper holes for trim. 4. Recess for face plate, the dimension is: L 81/32" x W 15/16" x D 7/32". OPTIONAL DOOR CORE DRILLING GUIDE #7000DG 7/32" P:\INSTALLATION INST\Electrified Lockset\INSTZ7800 REV D 1013 Page 1 Any suggestions or comments to this instruction or product are welcome. Please contact us through our website or engineer@sdcsecurity.com
2 B. Strike Installation: 1. Align strike template on jamb. Be sure to keep 3/8" distance between lock centerline and strike centerline. Recess 5/32" for flush fit of strike and dust box. 2. Mortise jamb according to measurement of strike template. Then fit strike and dust box into frame and secure into place with supplied screws. Jamb C L 47/8" 317/32" 1" Holes 11/8" Deep Strike C 3/8" L Lock C L 3/8" C. Install Lockcase Make sure the lock hand matches the door hand, use the following diagram to determine the hand of door. LH Left Hand INSIDE OF DOOR RH Right Hand OUTSIDE OF DOOR INSIDE OF DOOR LHRB Left Hand Reverse Bevel OUTSIDE OF DOOR RHRB Right Hand Reverse Bevel P:\INSTALLATION INST\Electrified Lockset\INSTZ7800 REV D 1013 Page 2
3 C. Install Lockcase (Continued) Instructions for changing lock hand: 1. Change latchbolt handing If the hand of the latchbolt doesn t match the door hand, remove the fixing screw and pull the latchbolt out from lock case. Turn the latchbolt 180 to change the handling. Position latchbolt back, into case and fasten it. Remove screw Pull out and turn 2. Change hand of lock For RH and RHRB, the catch screw will be on the lock case side. For LH and LHRB, the catch screw will be on the lock cover side. P:\INSTALLATION INST\Electrified Lockset\INSTZ7800 REV D 1013 Page 3
4 C. Install Lockcase (Continued) 3. Connect wires as shown on the lock cover diagram. 4. Insert lockcase into mortise cutout and fasten screws to door. D. Install Spindles 1. Insert spindle into outside hub of lock. 2. Insert inside spindle and tighten screw into outside spindle. E. Install Lever trim 1. Place the reversible spring cage onto the ferrules with arrow pointing in direction of lever rotation. 2. Install outside trim with mounting posts through door and position lever onto the spindle. Reversible spring cage Ferrule Mounting post Screw post P:\INSTALLATION INST\Electrified Lockset\INSTZ7800 REV D 1013 Page 4
5 E. Install Lever trim (Continued) 3. Install inside spring cage onto the spindle with the arrow pointing in the direction of inside lever rotation. 4. Install inside mounting plate onto spindle. Tighten with provided screw. 5. Cap inside rose over mounting plate. 6. Screw inside lever into position and tighten lever collar with spanner wrench. Spanner wrench F. Install Cylinder and Armor Face Plate 1. Screw cylinder into threaded hole of lock case. 2. Tighten the setting screw against cylinder(s) by turning clockwise as shown. 3. Install face plate onto lock case front and fasten with supplied screws. USE THIS CAM. P:\INSTALLATION INST\Electrified Lockset\INSTZ7800 REV D 1013 Page 5
6 INSTALLATION WIRE DIAGRAM Model 7800 Series 12/24VDC STANDARD WIRING BLU 12 AMP BLU 24 AMP LATCHED AND LOCKED STATUS DOOR POSITION STATUS REQUESTTOEXIT OUTPUT LLS DPS REX SECURE UNSECURE FROM LOCK / ORG/ YEL/ ORG YEL / ORG/ YEL/ Dual Coil Solenoid Optional Monitoring WIRING WITH OPTIONAL CABLE AND CONNECTOR GRN 12 AMP GRN 24 AMP LATCHED AND LOCKED STATUS DOOR POSITION STATUS REQUESTTOEXIT OUTPUT LLS DPS REX SECURE UNSECURE FROM LOCK CABLE ORG BRN YEL /YEL /BLU /GRN VIO GRY PNK Dual Coil Solenoid Optional Monitoring P:\INSTALLATION INST\Electrified Lockset\INSTZ7800 REV D 1013 Page 6
7 FAIL SAFE/FAIL SECURE CONVERSION Procedure To Change SDC Fail Safe Solenoid To Fail Secure Fail Safe Assembly Remove fail safe solenoid Disassemble fail safe solenoid by unscrewing rod tip assembly from plunger. Fail safe Plunger Solenoid body Rod tip assy. Spring and washer supplied in case for fail secure conversion. Fail Secure Assembly Insert washer and spring onto rod tip assembly and screw into plunger until it bottoms out. Insert plunger/rod tip into solenoid. Solenoid body Plunger Replace solenoid in holder as shown. Spring Washer Rod tip assy. Fail secure P:\INSTALLATION INST\Electrified Lockset\INSTZ7800 REV D 1013 Page 7
INSTALLATION INSTRUCTIONS Z7800 SERIES MORTISE LOCK
801 Avenida Acaso, Camarillo, Ca. 93012 (805) 494-0622 www.sdcsecurity.com E-mail: service@sdcsecurity.com A. Door Preparation: INSTALLATION INSTRUCTIONS Z7800 SERIES MORTISE LOCK 1. Measure desired height
More informationNote: The dimensions of the Template are shown in inches. See attached page for the Metric Conversion Table for millimeters.
801 Avenida Acaso, Camarillo, Ca. 93012 (805) 494-0622 www.sdcsecurity.com E-mail: service@sdcsecurity.com These instructions are presented a in step by step sequence. Please read it through before installation.
More informationInstallation Instructions for 45HW & 47HW Electrified Mortise Locks
Installation Instructions for 45HW & 47HW Electrified Mortise Locks Contents These installation instructions describe how to install your 45HW & 47HW Electrified Mortise Lock. Topics covered include: Finishing
More informationED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS
ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS Ver.2 1300 SERIES CONCEALED VERTICAL ROD DEVICE Top Strike Latch Screws Strike Screws Release Plunger Top Latch Plunger Screws
More informationINSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET
HIGH EDGE 2 1/4"(57mm) 03079400070 INSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET IMPORTANT: THIS LOCK IS NON-HANDED. LOCK IS FACTORY PACKED PREADJUSTED FOR 1³ ₄" (45mm)
More informationInstallation Instructions for 45H & 47H Mortise Locks
Installation Instructions for 45H & 47H Mortise Locks Contents These installation instructions describe how to install your 45H & 47H Mortise Lock. Topics covered include: Finishing the preparation...
More informationInstallation Instructions
VON DUPRIN Installation Instructions 98/9947WDC Concealed Vertical Rod Exit Device Wood Door Applications Devices covered by these instructions: 98/9947WDC Concealed Vertical Rod Device 98/9947WDC-F (Fire)
More informationTOOLS REQUIRED Metal Wood Wood and Metal Screws. #16 Drill #12-24 Tap. 1/8 Drill
DEVICES COVERED IN THIS DOCUMENT: 4700S Surface Vertical Rod Device 4700SF Fire Exit Surface Vertical Rod Device TOOLS REQUIRED Metal Wood Wood and Metal Screws Sex Bolts #7 Drill ¼ -20 Tap #16 Drill #12-24
More information33/3547A. Special tools needed: #10-24 tap Drill bits: #25, 5/16, 13/32, 1/2
911404-00 Concealed Vertical Rod Exit Device 33/3547A Installation Instructions Devices covered by these instructions: 33/3547A and 33/3548A Concealed Vertical Rod Exit Device 33/3547A-F and 33/3548A-F
More information98/9927. Devices covered by these instructions: Surface Vertical Rod Exit Device
911375-00 Surface Vertical Rod Exit Device 98/9927 Installation Instructions Devices covered by these instructions: 98/9927 Surface Vertical Rod Exit Device 98/9927-F (Fire) Surface Vertical Rod Exit Device
More informationInstallation Instructions
for s TOC Table of Contents 1 Mortise Lock Handing Instructions.... 2 2 3 4 5 Mortise Lock Door Preparation & Installation... 3 HSS Trim Installation.... 5 Knob x Knob...6 Lever x Knob....7 Turn-Piece
More informationOVERVIEW. Mounting Post (2 places) Cylinder Cam. Handing Pin
DEVICES COVERED IN THIS DOCUMENT: 46CE Cylinder Escutcheon Key locks and 46DT Dummy Trim Pull when dogged unlocks lever 46BE Blank Escutcheon Always operable 46NL Night Latch Key retracts latchbolt 46NK
More informationMORTISE LOCK INSTALLATION INSTRUCTIONS
MORTISE LOCK INSTALLATION INSTRUCTIONS INSPIRE TM ROSELESS DESIGNER TRIM FM 340 Rev. 10/18 TABLE OF CONTENTS: DOOR PREPARATION 1 ML2000 LOCK HANDING 2 FULL WORKING TRIM (STD) 3 HALF WORKING TRIM (M30)
More information33/3527A. Devices covered by these instructions: 33/3527A-F (Fire) Surface Vertical Rod Exit Device
*911403-00* 911403-00 Surface Vertical Rod Exit Device 33/3527A Installation Instructions Devices covered by these instructions: 33/3527A Surface Vertical Rod Exit Device 33/3527A-F (Fire) Surface Vertical
More informationTools Required. * When installing on a fire door, please see instructions below. *
CL615 Tubular Mortice Latch with Code Free option CL615 Tubular Mortice Latch with Code Free option Number relating to picture Item 1 Front Plate and handle * 2 Back Plate and handle * 3 Neoprene seals
More informationD3976 RECESSED EXIT INSTALLATION INSTRUCTIONS
PACKAGE CONTENTS PRODUCT MUST BE INSTALLED ACCORDING TO ALL APPLICABLE BUILDING AND LIFE SAFETY CODES TEMPLATE INSTALLATION INSTRUCTIONS STRIKE HAND TOOL 5/32 HEX KEY ROD END CAPS EXIT DEVICE CRANK ARM
More informationEntry Mortise Handleset
1. Pencil 2. No. 2 and No. 3 Phillips Head Screwdrivers 3. No. 1 and No. 2 Slotted Screw Drivers 4. 1/8" Allen Head Wrench 5. 3/4" Wood Chisel or Corner Chisel 6. Measuring Device 7. Lock Mortising Tool
More informationINSTALLATION INSTRUCTIONS CRL JACKSON
INSTALLATION INSTRUCTIONS CRL JACKSON 2085 CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com 11M0250 ORDER OF ASSEMBLY
More informationCRCODE-202. Mechanical Lock. Instruction and Programming Manual. Before Installing:
CRCODE-202 Mechanical Lock Instruction and Programming Manual Before Installing: 1. Please read the instructions carefully to prevent missing important steps. *Note: Improper installations may result in
More information33/35A Series. Devices covered by these instructions: Rim Exit Device. CD33/35A Rim Exit Device EL33/35A Rim Exit Device SS33/35A Rim Exit Device
911402-00 Rim Exit Device 33/35A Series Installation Instructions Devices covered by these instructions: 33/35A Rim Exit Device CD33/35A Rim Exit Device EL33/35A Rim Exit Device SS33/35A Rim Exit Device
More informationASSA ABLOY. Installation Instructions. MP9800 Series Multi-Point Lock. MP9800 Series Multi-Point Lock Wood Doors. Wood Doors ASSA ABLOY.
Installation Instructions MP9800 Series Multi-Point Lock MP9800 Series Multi-Point Lock, the global leader in door opening solutions 1 of 12 Copyright 2016 Corbin Russwin Inc., an Group company. Table
More information*D-1030* 1 PARTS CHECK 8 REVERSING INSTRUCTIONS F-XX-C & XX-C D Customer Service. Installation Instructions. Exit Devices
*D-1030* D-1030 F-XX-C & XX-C Exit Devices Installation Instructions 8 REVERSING INSTRUCTIONS TO REVERSE THE HANDING OF A (F)XX-C DEVICE NOTE: TO REVERSE TRIM, REFER TO SEPARATE INSTALLATION SHEETS. 1
More informationInstallation Instructions For The 8850FL Series Mortise eboss
Installation Instructions For The 8850FL Series Mortise eboss Electronic Battery Operated Security Solution FEATURES Battery Operated (Hardwire Capable) Motorized Grade 1 Mortise Lock 94 User Code Capacity
More informationWD WD7000 Series
WD-7000 12-WD7000 Series Wood Door Concealed Vertical Rod Multi-Point Lock Installation Instructions Copyright 2015, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction
More information* * 98/9950WDC. Fire-Rated Devices include these. additional components. 1-Point Latch (LBL)
*24739468* 24739468 98/9950WDC Installation Instructions 1-Point Latch (LBL) Fire-Rated Devices include these additional components Metal Edge Wrap required for 60 and 90-minute applications 2-Point Latch
More informationTH955 & TH959. Heavy Duty Thumbpiece Trim For use with ED5000 Series Exit Device. Metal, Wood or Composite Doors
TH955 & TH959 Heavy Duty Thumbpiece Trim For use with ED5000 Series Exit Device Metal, Wood or Composite Doors TH955 Classroom Function TH959 Storeroom Function 1 Template Top DOOR Holes Marked "" OUTSIDE
More informationFor installation assistance, contact SARGENT at DOORS SHOWN HERE SWING IN FOR ILLUSTRATION PURPOSES ONLY.
SARGENT Installation Instructions for LP8600 x LR8600 & 12-LP8600 x 12-LR8600 Series Low Profile Panic and Fire Exit Devices on Double Egress & Double Doors or LS8600 & 12-LS8600 Low Profile Exit Device
More informationInstalling Your Electronic Deadbolt
Ultra Security Plus Electronic Deadbolt Installation Instructions http://www.hberger.com/video-gallery/electronic-deadbolt New Installation Lock Location Preparation (Skip this section if you door has
More informationInstallation Instructions 50 (06-09) 1-15/32 15/32 21/32. 1/4-20 x 5/8" FHMS or #14 x 1/2" FHWS 1/16 1/4. Floor Plate
RIXSON ASSA ABLOY 3/4 Template Jamb 1/8 2- R. Max. 1-7/16 1-1/32 2-2-3/4 7/8 Dia. C L 1-1/4 Dia. Installation Instructions 50 (06-09) Finish Plate 340 TOP PIVOT Pivot Shown Engaged 9/16 1/16 1/4 1-15/32
More information98/ Customer Service # Dogging Key (use to lock down pushbar)
911373-00 Rim Exit Device 98/99 Installation Instructions Dogging Key (use to lock down pushbar) Customer Service 1-877-671-7011 www.allegion.com/us Allegion 2014 Printed in U.S.A. 911373-00 Rev. 05/14-f
More informationEntry Mortise Lock Set Lever to Lever
Entry Mortise Lock Set Lever to Lever 1 Lever 2 Escutcheon 3 Turn Piece 4 Mortise Lock 5 Scalp 6 Mortise Lock Strike 7 Mortise Lock Dust Box 8 Mortise Cylinder 9 Cylinder Swing Cover 10 Spindle 11 Spindle
More informationShetland Stalls Installation Instructions
Shetland Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 1/9/18 Before you start Kit can accommodate up to 12 wide stall front
More information7130(F) Series Mortise Exit Devices Installation Instructions
7130(F) Series Mortise Exit Devices Installation Instructions Outside Trim Device is packed ready for any Yale 650F or 660F Series Trim. End Clamp (3) 8-32 x 5/16" PUFHMS End Cap (2) 1/4-20 x 1" PPHMS
More informationInstallation Instructions
Installation Instructions 8000/8300 Series Electric Strike Product Components HES, Inc. 22630 N. 17th Ave. Phoenix, AZ 85027 800-626-7590 www.hesinnovations.com 1 1 2 8000/8300 Electric Strike Body Sticky
More informationInstallation Instructions II-2/4/5K-0608
Installation Instructions II-2/4/5K-0608 Box Contents Check the contents of the box are correct according to the model 2010 4010 4020 5010 5020 1 Front Plate 2/4000 - - 2 Front Plate 5000 - - - 3 Back
More informationINSTALLATION INSTRUCTIONS CRL JACKSON
INSTALLATION INSTRUCTIONS CRL JACKSON 3185 MID-PANEL CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com 11M0252 ORDER
More informationSafety glasses Measuring tape Level Pencil Power drill Center punch Phillips screw driver Saw horse
EX76 Concealed Vertical Rod Exit Device Preparation Guide and Installation Instructions Box Contents EX76 Concealed Vertical Rod Exit Device Back Bar Active Push Bar Filler Plate Door Kit with Templates
More informationINSTALLATION INSTRUCTIONS CRL JACKSON
INSTALLATION INSTRUCTIONS CRL JACKSON 1285 CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com 11M0248 ORDER OF ASSEMBLY
More informationStage 2: Preparing the door (read in conjunction with Hole Drilling Options on back of Template).
There are three stages to fitting the CL100 mortise case: Stage 1: Marking out the position of the lock. Stage 2: Preparing the door by mortising and drilling holes. Stage 3: Fitting lock, door furniture,
More information8800 Series Mortise Lockset Knob, Lever, Reflections and Security Trims Installation Instructions
8800 Series Mortise Lockset Knob, Lever, Reflections and Security Trims Installation Instructions IMPORTNT: The accuracy of the door preparation is critical for the proper functioning and security of this
More informationASSA ABLOY. Installation Instructions. MP9800 Series Multi-Point Lock. MP9800 Series Multi-Point Lock Hollow Metal & Aluminum Doors
Installation Instructions MP9800 Series Multi-Point Lock MP9800 Series Multi-Point Lock, the global leader in door opening solutions 1 of 12 Copyright 2016 Corbin Russwin Inc., an Group company. All rights
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS ANSI/BHMA - A156.2 BOX CONTENTS CHECK THAT THE CONTENTS OF YOUR BOX ARE CORRECT ACCORDING TO THE MODEL Model 600/605 Model 610/615 Model 620/625 1 Front plate and handle 2 Back
More informationCM5100 COMPUTER MANAGED CYLINDRICAL LOCK HARD-WIRED (FSE/FSA) INSTALLATION MANUAL
The 5100 series lock is a stand-alone, microprocessor controlled, electromechanical locking system. The 5100 employs a heavy-duty mechanical design which is easy to install and highly reliable. The FSE
More informationINSTRUCTIONS TS93 GSR PT RIGHT HAND ACTIVE LEFT HAND INACTIVE RIGHT HAND INACTIVE LEFT HAND ACTIVE
INSTRUCTIONS ATTENTION!!! Before you begin, determine installation type (RIGHT HAND ACTIVE OR INACTIVE). Door coordinator suitable for door from 59 to 98 in width. Inactive door width in the case of unequal
More informationPassage Mortise Lock Set Lever to Lever
Passage Mortise Lock Set Lever to Lever 1 Lever 2 Escutcheon 3 Mortise Lock 4 Scalp 5 Mortise Lock Strike 6 Mortise Lock Dust Box 7 Spindle 8 Spindle Spring 9 Spindle Retainer 2 1 9 8 7 9 7 8 3 1 2 4 5
More information1530(F) Mortise Exit Devices Installation Instructions
1530(F) Mortise Exit Devices Installation Instructions Singe Doors or Pairs (2) 12-12-24 PFHUM/WS 798 Universal Strike Standard Device Package Devices are packed ready for application reinforced metal
More informationThis is a printable pdf document. For Smartphone-friendly version, tap or click here.
This is a printable pdf document. For Smartphone-friendly version, tap or click here. *911373-00* 911373-00 Rim Exit Device 98/99 Installation Instructions Dogging Key (use to lock down pushbar) Customer
More informationLATCHBOLT FILLER PLATE ASA FILLER PLATE A. SINGLE DOOR B. DOUBLE DOOR WITH MULLION C. DOUBLE DOOR WITHOUT MULLION END COVER MOUNTING BRACKET
F2000R 2012.03 1/4 x1 1/2 (9 PCS) SELF TAPPING MACHINE SCREWS 1/4-20P x 3/4 (3 PCS) 1/4-20P x 3/4 (6 PCS) ROUND HEAD MACHINE SCREWS THRU BOLT (6 PCS) END COVER MOUNTING BRACKET 1/4 x 1 1/4 (3 PCS) 1/4
More informationCrossOver X25 Lock Installation Need another copy of these installation sheets? You can download one at
CrossOver X25 Lock Installation Need another copy of these installation sheets? You can download one at www.crossoverlock.com/supportcenter.htm 1 Back view of installation Major lock parts 1. Rear handle
More informationPMR ELECTRONIC LOCK USER GUIDE
封底 封面 148.5 x 210(mm) www.ezset.com.tw PMR ELECTRONIC LOCK USER GUIDE 封面裡 Parts Introduction Do not use an electric screwdriver when installing the product! Installation Procedures 1. Draw horizontal lines
More informationMORTISE LOCKS LA1Tx7 //DATASHEET
//DATASHEET SATO ocks AElement Access control requires a good, reliable door locking system. SATO offers a wide range of mortise locks in order to ensure that the door is correctly locked. Whether you
More informationRim-Lock Door Set Installation Instructions
Rim-Lock Door Set Installation Instructions Let s get started Check Your Parts List Two Doorknobs with Set Screws B. Doorknob Spindle C. Rim Lock with Mounting Screws D. Keeper with Mounting Screws E.
More informationCL4500 Installation Instructions
CL4500 Installation Instructions Box Contents Check the contents of the box are correct according to the model 4510 4520 1 Front Plate 2 Back Plate 3 Lever Handles 4 Gaskets 5 Sprung Spindle (x1) 6 Spring
More informationDOOR TECHNOLOGY ORDER CATALOG SECTION Tools & Accessories for Door Lock Installation
DOOR TECHNOLOGY ORDER CATALOG SECTION 03.11 Tools & Accessories for Door Lock Installation Table of Contents 03.11 Tools & Accessories for Door Lock Installation Door Slab Jig...03.11.5 Router Bits for
More informationDoor Hardware Installation Instructions. For Assistance Call:
For Assistance Call: Door Hardware Installation Instructions Single Cylinder NOTE: s fit doors 1-3/4 to 2-1/4 thick. For thicker doors, please call customer service. Carefully unpackage all components
More informationEXIT DEVICE OPERATION FIRE DOOR LABELS, STRIKES AND FRAME SCREWS FOR INFORMATION CALL OR VISIT RITEDOOR.COM
RECORD & LABELS WHAT THIS OWNER'S CAN DO FOR YOU It explains exactly how The Rite Door operates. It explains periodic maintenance requirements necessary to assure reliable operation. It explains simple
More information4600 Series Rim Narrow Stile Exit Device Installation Instructions I-ED01162
DEVICES COVERED IN THIS DOCUMENT: 4600 Series Rim Panic Narrow Stile Exit Device 4600 Series Rim Fire Narrow Stile Exit Device OVERVIEW Outside of Door RHR LHR Inside of Door APPLICATIONS 4950 BLADE STOP
More informationCM5500 COMPUTER MANAGED MORTISE LOCK INSTALLATION MANUAL
The 5500 series lock is a stand-alone, microprocessor controlled, electromechanical locking system. The 5500 employs a heavy-duty mechanical design with fewer moving parts that a standard mechanical mortise
More informationCongratulations! You are now on your way to enriching your life with! Figure #5. Step 5 Install the Dummy Deadbolt. Step 3 Drill the Door
C) Using the base point as your reference, measure up 8-1/32 and mark a horizontal line. Measure in from the edge of the door the distance of your backset and mark where the two lines cross. This will
More informationP USHbutton 500 series
Dimensions 35 60mm 178mm Model 500/505 For use with existing lock 1 6 2 7 3 8 4 9 5 0 1 6 2 7 3 8 4 9 5 0 Features ode Free Entry Mode by turning the slotted button 90 degrees after entering the code (models
More informationMORTISE LOCK INSTALLATION INSTRUCTIONS
MORTISE LOCK INSTALLATION INSTRUCTIONS MUSE O DESIGN ER TRIM FM 601 Rev. C (10/18) WARNING This product can expose you to lead which is known to the state of California to cause cancer and birth defects
More informationINSTALLATION INSTRUCTIONS
PARTS LIST ITEM PART DESCRIPTION QTY 73-A 503F 9MM 50G 5A 50E 505S 50H Connector Bracket Door Stops Support Bar Panel Glass Bracket Wall Mount Bracket Rollers Center Guide Recessed Finger Pull Fixed Panel
More information*18758* 2030 Series. 1 Installation. 2 Adjustment. 3 Hold Open Information BACKCHECK. * Hold open tracks. Installation Instructions
18758 18758 No maintenance required. 2035 EN 4 1 Installation 1a The hand of the door and the closer must be the same. RH or LH will be stamped on the mounting plate. See the proper template for your application.
More informationInstallation Instructions For Profile Series v.g1 Exit Device
Installation Instructions For Profile Series v.g1 Exit Device A7757C Copyright 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part
More informationWOOD DOOR INSTALLATION
1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-32VD9W TEMPLATE FOR VON DUPRIN 99 RIM WOOD DOOR INSTALLATION WHEN USING
More informationFRAME PREPARATION 3900/8900 SURFACE LATCH CONCEALED ROD EXIT DEVICE INSTALLATION INSTRUCTIONS HOW TO FIND BACKSET. Date: Appvd: *13/16 2 3/4" 3/4 HOLE
FRAME PREPARATION 3/4 3/4 HEADER STRIKE STRIKE STOP FRAME 13/16 13/16 RHR LHR INTERIOR FACE OF LHR INTERIOR FACE OF RHR STRIKE POST *13/16 * MEASURED FROM THE INTERIOR SURFACE. BE SURE TO ADJUST FOR SILENCERS
More informationED5800 (A) Series. Installation Instructions. Concealed Vertical Rod. Exit Device WARNING
Strike Shim (2) Supplied Strike Plate (3) 10-24 x 3/4" PFHMS (6) 10-24 x 1/2" PFHMS Top Latch TopTube Concealed Vertical Rod Exit Device Important: For use with metal doors only. Device is packed ready
More informationDublin Stalls Installation Instructions
Dublin Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 9/13/17 Part Identification Round Track Bracket (4) (Not Painted) Round
More informationCONCEALED ROD CRASH BAR PR-7085 SERIES EXIT DEVICE ASSEMBLY DETAILS PR mm. 10mm. Lock cylinder. 10mm. Cross bar length (see note #8) Dogging
Floor line TITLE ASSEMLY DETAILS PR-7085 4:02 Hinge stile (inside) Lock stile (inside) Lock stile (outside) Drill 5mm (.20) and tap 1/4-20 (2) Drill 7mm (.266) holes (2) 9mm 12mm See note #6 160mm 9.5mm
More informationInstallation Instructions
Installation Instructions 8000/8300 Series Electric Strike Product Components HES, Inc. 22630 N. 17th Ave. Phoenix, AZ 85027 800-626-7590 www.hesinnovations.com 1 1 2 8000/8300 Electric Strike Body Sticky
More informationInstallation Instructions FE6800 Series Multi-Point Lock
Installation Instructions FE6800 Series Multi-Point Lock To view the QR Code video clips within this document, download a free mobile app and scan the QR Code with your mobile device. The complete video
More information351 DOOR CLOSER WITH DOUBLE LEVER ARM (OP) INSTALLATION INSTRUCTIONS
2 351 DOOR CLOSER WITH DOUBLE LEVER ARM (OP) INSTALLATION INSTRUCTIONS Strength Adjustable From Size 1 Thru 6 CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE Auxiliary door
More informationActive Push Bar. Safety glasses Measuring tape Level Pencil Power drill Drill bits: 5/32, 3/4 Center punch Phillips screw driver
EX88 Interlocking Rim Exit Device Preparation Guide and Installation Instructions Box Contents EX88 Interlocking Rim Exit Device Back Bar Filler Plate Active Push Bar Cylinder and Trim Interface Kit Mounting
More informationInstallation Instructions For Profile Series v.g1 Cylindrical Lock
Installation Instructions For Profile Series v.g1 Cylindrical Lock A7755A Copyright 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or
More information(Wood Door and Frame)
ITS961 and ITS965 Closer in Door Track in Frame (Wood Door and Frame) 1 (REFERENCE UNIT CARTON FOR ACCESSORIES AND OPTIONS SUPPLIED) Determine hand of door. Prepare door and frame according to template
More informationNo. 059FL. No. 251FL. No. 260FL. No. 305RE. Etruscan Bronze. Florentine Brass. Siena Brass (D) All designs available in these finishes.
SINCE 1964 No. 059FL No. 251FL No. 260FL No. 305RE 2 Etruscan Bronze (ETR) Florentine Brass (D) Siena Brass (BAS) Venetian Nickel (BPS) All designs available in these finishes. No. 309RE No. 331FL No.
More informationShepherd 210A Fingerprint Door Lock Installation Manual V1.1
Shepherd 210A Fingerprint Door Lock Installation Manual V1.1 Hongda USA Inc. 2505 Technology Dr. #2-6A, Hayward, CA 94545, USA Phone: (510) 887-5682 Fax: (510) 372-0487 Email: info@hongdausa.com Website:
More informationINSTRUCTIONS FOR HIT LOCK MORTISER
1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-66-200 LOCK MORTISER WHEN USING POWER TOOLS ALWAYS WEAR EYE AND EAR
More informationCM5500 COMPUTER MANAGED MORTISE LOCK HARD-WIRED (FSE/FSA) INSTALLATION MANUAL
The 5500 series lock is a stand-alone, microprocessor controlled, electromechanical locking system. The 5500 employs a heavy-duty mechanical design with fewer moving parts that a standard mechanical mortise
More informationJenny Legs Assembly Instructions
Jenny Legs Assembly Instructions R EXTENDED PHILLIPS BIT MM ALLEN WRENCH 6MM HEX DRIVE /" 007 Steelcase Inc. Grand Rapids, MI 90 U.S.A. Printed in U.S.A. Page of 6 88000 Rev F Jenny Club Instructions:
More informationMelamine Plastic Laminate. Toilet Partition Installation Manual
Melamine Plastic Laminate Toilet Partition Installation Manual PHONE: FAX: 1-866-317-2786 ATTENTION DO NOT MIX FASTENER PACKS EACH FASTENER PACK HAS THE NECESSARY BOLTS, BARRELS AND SCREWS TO INSTALL THE
More informationCONCEALED VERTICAL ROD PANIC EXIT DEVICE
INSTALLATION INSTRUCTIONS CRL JACKSON 1085-1085P CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com 11M0236 ORDER OF
More information2. Connect driver to power source leads. After connections are made, place driver above ceiling. SEE MINIMUM SPACE REQUIREMENTS BELOW.
INSTALLATION INSTRUCTIONS INSTALLATION: 1. Cut proper opening in ceiling. Round: 140mm Ø, Square: 140mm x 140mm 140mm Ø 140mm x 140mm 2. Connect driver to power source leads. After connections are made,
More informationv1.0 ASSEMBLY GUIDE Mia Wide Bookcase
v1.0 ASSEMBLY GUIDE Mia Wide Bookcase Components Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase.
More information33/3550AWDC. Fire-Rated Devices include these. additional. components. 1-Point Latch (LBL) Metal Edge Wrap required for 60 and 90-minute applications
24739476 33/3550AWDC nstallation nstructions 1-Point Latch (LBL) Fire-Rated Devices include these additional components Metal Edge Wrap required for 60 and 90-minute applications 2-Point Latch includes
More information316R Series Installation Instructions
316R Series Installation Instructions Multi size 1 thru 6 Non hold open closers CAUTION An incorrectly installed or improperly adjusted closer can cause property damage or personal injury. These instructions
More informationAdams Rite. Standard & Heavy Duty Deadlatches Series Heavy Duty Deadlatch
Standard & Heavy Duty Deadlatches 4900 Series Heavy Duty Deadlatch Function: Flexibility of traffic control and installation is offered by the 4900 Series Deadlatches. A reverse turn of the key while bolt
More informationBEFORE STARTING INSTALLATION
VON DUPRIN Installation Instructions 22 Rim Device Devices covered by these instructions: 22 Rim Device 22-F Fire Exit Rim Device BEFORE STARTING INSTALLATION 1. Check hardware schedule for strikes, fasteners,
More informationInstallation Type. Edge of Door. Pull (Hinge) Side Mounted. Hinge Edge of Door. Push (Stop) Side Mounted
Installation Instructions CAUTION An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility
More informationSentinel Series Cigar Humidor End Tables
Sentinel Series Cigar Humidor End Tables Assembly Instructions Models: Sentinel 500, 1000 and 1500 Style: Traditional SENTINEL ASSEMBLY INSTRUCTIONS Congratulations! You have purchased a superior cigar
More information* * 9875/ Customer Service #10-24 # Dogging Key (use to lock down pushbar)
*911374-00* 911374-00 Mortise Exit Device 9875/9975 Installation Instructions #10-24 #12-24 Dogging Key (use to lock down pushar) Customer Service 1-877-671-7011 www.allegion.com/us Allegion 2015 Printed
More informationInstallation Manual for Metal Toilet Partitions Standard Series
For Video instructions http://www.hadrian-inc.com/tech-data/installation/toilet-partitions.aspx P a g e 1 Table of Contents Page General Notes and Tools Required 3 STEP 1: Establish Floor Bracket Locations
More informationSenior Swing. Caution
*740132* 740132 2800 Overhead Concealed Series 9500 Surface Applied Series Senior Swing Installation Instructions Caution LCN Senior Swing The Senior Swing Power Operator System is a low energy product
More information86-1/2" TRACK INSTALLATION GUIDE
BARN TRACK 86-1/2" TRACK INSTALLATION GUIDE READ ALL INSTRUCTIONS AND REVIEW DIAGRAMS BEFORE BEGINNING THE INSTALLATION TO GET A THOROUGH UNDERSTANDING OF THE PROCESS. BEFORE YOU BEGIN This kit comes with
More informationInstallation Instructions
Installation Instructions CAUTION An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility
More informationInstallation Guide. Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate
Installation Guide Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate The purpose of this guide is to: 1. Describe mounting
More information3 wide x 3 deep Video Wall Display Installation Guide
HoverTrack Series 3 wide x 3 deep Video Wall Display Installation Guide VWD-3X3-X462 This display kit mounts NEC X461UN and X462UNS LCD monitors in a 3 wide by 3 deep landscape configuration. The frame
More informationTravel Trailer Latch With Dead Bolt Trailer Latch With Dead Bolt. U.S. Patent No. 5,927,773
60-250 Travel Trailer Latch With Dead Bolt 60-251 Trailer Latch With Dead Bolt Service Manual (Installation and Troubleshooting) U.S. Patent No. 5,927,773 CONTENTS 1. BASIC COMPONENTS 2. INSTALLATION OF
More informationOFFSET PIVOTS STOREFRONT HARDWARE
Trans-Atlantic offset pivots are used for both flush face frame installations and ⅛" recessed door applciations. Pivots replace most major door manufacturers. Suitable for aluminum doors weighing up to
More informationPet Door Panel Installation Manual
Pet Door Panel Installation Manual 400-558-1 1 4/3/03, 3:26 PM Components: Pet Door Panel Panel Latch Assembly Foam Weather-stripping Glass Sweep (4) Binding Posts (6) #6 x 1/2 Sheet Metal Screws (4) 8-32
More information