Entry Mortise Handleset

Size: px
Start display at page:

Download "Entry Mortise Handleset"

Transcription

1 1. Pencil 2. No. 2 and No. 3 Phillips Head Screwdrivers 3. No. 1 and No. 2 Slotted Screw Drivers 4. 1/8" Allen Head Wrench 5. 3/4" Wood Chisel or Corner Chisel 6. Measuring Device 7. Lock Mortising Tool (recommended) 8. Router and Lock Face Template TOOLS REQUIRED 9. Combination Square 10. Awl 11. Hacksaw 12. File (Wood Rasp & Metal) 13. Baldwin Aligning Tool 14. Drill and Assorted Bits: 15. Screw Wax or Soap 16. Powdered Chalk, Graphite or Lipstick NOTE: In order to successfully install a mortise lock and trim, a minimum of average skill level is required with use of the above listed tools. Backset is located from low side of beveled door, please adjust accordingly for non-beveled doors. Read and understand the provided instructions BEFORE attempting to mark or cut the door and/or frame. If there are any questions before you begin installation, phone or visit your nearest Baldwin Distributor or contact the Technical Service Department at Baldwin at Fasteners Diagram A INSIDE INTERIOR TURNKNOB SHANK Thru-bolting shown is for 1-3/4", 2" & 2-1/4" THK Doors 1/16", 1/8", 5/8", 3/4, 1", 1-1/2", 2-1/8" Chateau HALF SPINDLE PLUG THRU- BOLTING & LOCKWASHER #10-32 x 1-3/4" OVAL HEAD #8-32 x 7/32" FLAT HEAD Craftsman #10-32 x 1/2" FLAT HEAD 1 #10-32 x 3-1/4" OVAL HEAD #10-32 x 1/2" PAN #10-32 x 1" FLAT HEAD, SEMS HEAD COMBINATION SHOWN ACTUAL SIZE 1 Used with strike faceplate mounting BASE ARMOR PLATE S ARMOR PLATE (SCALP) Villa LOCK FRONT S LOCK FRONT EXTERIOR OUTSIDE

2 1 MARK THE DOOR 2 DOUBLE CHECK COMPATIBILITY OF DOOR STILE & TRIM 3 MORTISE LOCK POCKET FOR LOCK BODY Mark the door at 36" above finished floor, or if retrofit, at appropriate location to coordinate with existing strike preparations. This will be the centerline of knob or lever location (not the centerline of lock.) DOOR EDGE Make sure that the door stile will accommodate the intended lock and trim. Ensure trim will not interfere with doorstop or extend over door panel or glass Mortise the pocket in the door 1/8" deeper than the lock being installed. Refer to the Installation Template Guide Chart for exact size of mortise pocket. 4a PREPARE FOR LOCK FRONT 4b PREPARE FOR LOCK FRONT 5 CUT RELIEF POCKETS Route for the lock front. Square the corners. Cut the relief pockets 3/8" deep on both sides for the Latch Hinge, 2-1/2" & 2-3/4" backset only (does not apply for 1" front) 6 DETERMINE HOLE PATTERN REQUIRED FOR TRIM ON TEMPLATE GUIDE CHART 7 MARK DOOR ** BACKSET IS LOCATED FROM LOW SIDE OF BEVELED DOOR 8 DRILL HOLES Determine hole pattern required for trim (see Installation Template Guide chart). Mark the listed holes on the lock template enclosed with the lock. For 1-3/4" doors, fold lock template. Mark door at appropriate locations for lock and trim. MARK APPROPRIATE BACKSET. Extra thick conditions, see General notes on back page. Drill appropriate holes as indicated on lock template. DO NOT OVERSIZE HOLES.

3 9 THREAD PLUG 10 ADJUST BEVEL AND INSTALL LOCK 11 Handle Set Trim (Diagram A) INSERT SPINDLE TAPE #10-32 x 1/2" PAN HEAD, SEMS Thread the cylinder plug on interior side of lock. Place a strip of tape over plug to keep it from turning. (Double cylinder functions: OMIT THIS STEP.) #10-32 x 1" FLAT HEAD COMBINATION S Drill (2) 1/8" pilot holes for the lock face, adjust the bevel and install the lock. Shim between the lock and door on cylinder side as shown to prohibit the cylinder from pulling the lock off center. Tighten the lock front screws 12 SIZE THUMBPIECE 13 INSTALL EXTERIOR SIDE TRIM 14 AND BOTTOM THRU-BOLT INTERIOR For handleset trim install the spindle from the inside and thread the screw and lockwasher into the spindle from the outside. Tighten securely. INSTALL EXTERIOR SHOWN ACTUAL SIZE #10-32 x 3-1/4" OVAL HEAD A = 3/8" - For 2-1/4" Thk Door B = 1/2" - For 2" Thk Door C = 5/8" - For 1-3/4" Thk Door Note: 3" Thk Door requires no cutting Cut the thumbpiece to fully engage the lift lever. Mount exterior trim, aligning thumbpiece properly, using thru-bolt & standoff. Use screw base on lower pull mounting. Place the cylinder through the trim, insert key 2/3 the way into the cylinder and carefully thread the cylinder into the lock. Do not tighten. 15 INSTALL INTERIOR SIDE TRIM AND REMAINING THRU-BOLTING 16 TIGHTEN LOCK FRONT S 17 INSTALL ARMOR PLATE #10-32 x 1-3/4" OVAL HEAD SET #8-32 x 7/32" FLAT HEAD S #10-32 x 3-1/4" Mount interior trim by placing turnpiece spindle into lock hub and slide knob /lever assembly onto mortise spindle. Tighten the trim thru-bolts. Thread the cylinder in and tighten/loosen cylinder as required to ensure 'Baldwin' logo is in the horizontal position. Lock the cylinder in place by tightening the cylinder set screw. DO NOT OVERTIGHTEN. Install the armor plate (scalp).

4 18 MARK AND MORTISE JAMB FOR STRIKE LOCATION 19 INSTALL DUST BOX 20 INSTALL SECURITY STRIKE Mark the jamb for the proper strike location. Coat extended bolt head with graphite, powdered chalk or lipstick. Retract the bolt, close the door and actuate the knob or lever several times. This will mark the jamb. Add approximately 1/32" clearance from that mark. * Chisel cavity 1/4" deep. Install the dust box. Pre-drill holes using 1/8" bit. Install security strike. Ensure 3" screws for security strike are installed on the stop side of the plate. Note: Security Strikes are supplied ONLY with locks, which utilize cylinders. 21 INSTALL STRIKE PLATE * Apply any weather-stripping before strike has been installed. General Notes: Paper template is designed for 1-3/4" thick doors. For extra thick doors, measure backset from center of door edge. Tape supplied template to the door to locate placement of hole pattern of lock and trim. ** Paper template is located on the low side of the bevel on the door. When installing hardware on metal doors, ensure the door was designed to accommodate mortise locks. If in doubt, check with your local door distributor or door manufacturer. Removal of hardware from doors is recommended before painting and finishing of the door. Allow finishing materials to fully cure before reinstalling hardware, usually ten days to two weeks. Check paint manufacturer instructions. Install the strike plate. Retain these instructions in a safe place should you need to disassemble the lock trim or require Baldwin Hardware Corporation's assistance.

5 Full Inactive Mortise Handleset 1. Pencil 2. No. 2 and No. 3 Phillips Head Screwdrivers 3. No. 1 and No. 2 Slotted Screw Drivers 4. 3/4" Wood Chisel or Corner Chisel 5. Measuring Device 6. Lock Mortising Tool (recommended) 7. Router and Lock Face Template 8. Combination Square TOOLS REQUIRED 9. Awl 10. File (Wood Rasp & Metal) 11. Drill & Bits: 1/16", 1/8", 5/8", 3/4", 1", 1-1/2", 2-1/8" 12. Screw Wax or Soap 13. Powdered Chalk, Graphite or Lipstick NOTE: In order to successfully install the dummy mortise trim, a minimum of average skill level is required with use of the above listed tools. Backset is located from low side of beveled door, please adjust accordingly for non-beveled doors. Read and understand the provided instructions BEFORE attempting to mark or cut the door and/or frame. If there are any questions before you begin installation, phone or visit your nearest Baldwin Distributor or contact the Technical Service Department at Baldwin at Fasteners Diagram A INSIDE INTERIOR DUMMY CAP (ENSURE 'BALDWIN' IS HORIZONTAL) Chateau Full Inactive Mortise THRU- BOLTING #10-32 x 1-3/4" OVAL HEAD Craftsman #10-32 x 3-1/4" OVAL HEAD BASE SHOWN ACTUAL SIZE Villa Thru-bolting shown is for 1-3/4", 2" & 2-1/4" THK Doors EXTERIOR OUTSIDE

6 Full Inactive Mortise Handleset 1 MARK THE DOOR 2 DETERMINE HOLE PATTERN REQUIRED FOR TRIM ON GUIDE SHEET 3 MARK DOOR ** BACKSET IS LOCATED FROM LOW SIDE OF BEVELED DOOR Full Inactive Mortise Mark the door at 36" above finished floor, or if retrofit, at appropriate location to coordinate with existing strike preparations. This will be the centerline of knob or lever location (not the centerline of lock.) Determine hole pattern required for trim (see Installation Template Guide chart). Mark the listed holes on the lock template enclosed with the lock. For 1-3/4" doors, fold the lock template. Mark door at appropriate locations for lock and trim. MARK APPROPRIATE BACKSET. Extra thick conditions, see General notes on back page. 4 DRILL HOLES 5 INSTALL EXTERIOR SIDE TRIM 6 INSTALL INTERIOR SIDE TRIM AND BOTTOM THRU-BOLT AND REMAINING THRU-BOLTING #10-32 x 1-3/4" #10-32 x 3-1/4" #10-32 x 3-1/4" Drill appropriate holes & slot as indicated on lock template. DO NOT OVERSIZE HOLES. Check dummy cylinder cap orientation. Mount exterior trim using thru-bolt & standoff. Use screw base on lower pull mounting. Mount interior trim by installing remaining thru bolting. 7 MARK AND MORTISE DOOR FOR STRIKE LOCATION 8 INSTALL DUST BOX 9 INSTALL SECURITY STRIKE Mark the dummy door for the proper strike location. Coat extended bolt head with graphite, powdered chalk or lipstick. Retract the bolt, close the door and actuate the knob or lever several times. This will mark the door. Add approximately 1/32" clearance from that mark. * Install the dust box. Pre-drill holes using 1/8" bit. Install security strike. Ensure 3" screws for security strike are installed on the stop side of the plate. Note: Security Strikes are supplied ONLY with locks, which utilize cylinders.

7 Full Inactive Mortise Handleset 10 INSTALL STRIKE PLATE Install the strike plate. Full Inactive Mortise General Notes: Paper template is designed for 1-3/4" thick doors. For extra thick doors, measure backset from center of door edge. Tape supplied template to the door to locate placement of hole pattern of lock and trim. ** Paper template is located on the low side of the bevel on the door. When installing hardware on metal doors, ensure the door was designed to accommodate mortise locks. If in doubt, check with your local door distributor or door manufacturer. Removal of hardware from doors is recommended before painting and finishing of the door. Allow finishing materials to fully cure before reinstalling hardware, usually ten days to two weeks. Check paint manufacturer instructions. Retain these instructions in a safe place should you need to disassemble the lock trim or require Baldwin Hardware Corporation's assistance.

Entry Mortise Lock Set Lever to Lever

Entry Mortise Lock Set Lever to Lever Entry Mortise Lock Set Lever to Lever 1 Lever 2 Escutcheon 3 Turn Piece 4 Mortise Lock 5 Scalp 6 Mortise Lock Strike 7 Mortise Lock Dust Box 8 Mortise Cylinder 9 Cylinder Swing Cover 10 Spindle 11 Spindle

More information

Passage Mortise Lock Set Lever to Lever

Passage Mortise Lock Set Lever to Lever Passage Mortise Lock Set Lever to Lever 1 Lever 2 Escutcheon 3 Mortise Lock 4 Scalp 5 Mortise Lock Strike 6 Mortise Lock Dust Box 7 Spindle 8 Spindle Spring 9 Spindle Retainer 2 1 9 8 7 9 7 8 3 1 2 4 5

More information

Door Hardware Installation Instructions. For Assistance Call:

Door Hardware Installation Instructions. For Assistance Call: For Assistance Call: Door Hardware Installation Instructions Single Cylinder NOTE: s fit doors 1-3/4 to 2-1/4 thick. For thicker doors, please call customer service. Carefully unpackage all components

More information

INSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET

INSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET HIGH EDGE 2 1/4"(57mm) 03079400070 INSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET IMPORTANT: THIS LOCK IS NON-HANDED. LOCK IS FACTORY PACKED PREADJUSTED FOR 1³ ₄" (45mm)

More information

Safety glasses Measuring tape Level Pencil Power drill Center punch Phillips screw driver Saw horse

Safety glasses Measuring tape Level Pencil Power drill Center punch Phillips screw driver Saw horse EX76 Concealed Vertical Rod Exit Device Preparation Guide and Installation Instructions Box Contents EX76 Concealed Vertical Rod Exit Device Back Bar Active Push Bar Filler Plate Door Kit with Templates

More information

Installation Instructions For The 8850FL Series Mortise eboss

Installation Instructions For The 8850FL Series Mortise eboss Installation Instructions For The 8850FL Series Mortise eboss Electronic Battery Operated Security Solution FEATURES Battery Operated (Hardwire Capable) Motorized Grade 1 Mortise Lock 94 User Code Capacity

More information

7130(F) Series Mortise Exit Devices Installation Instructions

7130(F) Series Mortise Exit Devices Installation Instructions 7130(F) Series Mortise Exit Devices Installation Instructions Outside Trim Device is packed ready for any Yale 650F or 660F Series Trim. End Clamp (3) 8-32 x 5/16" PUFHMS End Cap (2) 1/4-20 x 1" PPHMS

More information

For installation assistance, contact SARGENT at DOORS SHOWN HERE SWING IN FOR ILLUSTRATION PURPOSES ONLY.

For installation assistance, contact SARGENT at DOORS SHOWN HERE SWING IN FOR ILLUSTRATION PURPOSES ONLY. SARGENT Installation Instructions for LP8600 x LR8600 & 12-LP8600 x 12-LR8600 Series Low Profile Panic and Fire Exit Devices on Double Egress & Double Doors or LS8600 & 12-LS8600 Low Profile Exit Device

More information

ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS

ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS Ver.2 1300 SERIES CONCEALED VERTICAL ROD DEVICE Top Strike Latch Screws Strike Screws Release Plunger Top Latch Plunger Screws

More information

Installation Instructions ENGLISH

Installation Instructions ENGLISH Installation Instructions ENGLISH Interior Latchset PRIVACY (Bed & Bath) PASSAGE (Hall & Closet) PK.5400 Congratulations! With your purchase of this Interior Latchset, you re among a group of discerning

More information

Installing Your Electronic Deadbolt

Installing Your Electronic Deadbolt Ultra Security Plus Electronic Deadbolt Installation Instructions http://www.hberger.com/video-gallery/electronic-deadbolt New Installation Lock Location Preparation (Skip this section if you door has

More information

INSTALLATION INSTRUCTIONS REPLACING EXISTING DEADBOLT ASSEMBLY

INSTALLATION INSTRUCTIONS REPLACING EXISTING DEADBOLT ASSEMBLY INSTALLATION INSTRUCTIONS REPLACING EXISTING DEADBOLT ASSEMBLY A B C L M N D E F G O P Q H I J Tools provided in Amesbury installation kit: (A) door router fixture, (B) doorframe router fixture, (C) ½

More information

Congratulations! You are now on your way to enriching your life with! Figure #5. Step 5 Install the Dummy Deadbolt. Step 3 Drill the Door

Congratulations! You are now on your way to enriching your life with! Figure #5. Step 5 Install the Dummy Deadbolt. Step 3 Drill the Door C) Using the base point as your reference, measure up 8-1/32 and mark a horizontal line. Measure in from the edge of the door the distance of your backset and mark where the two lines cross. This will

More information

BEFORE STARTING INSTALLATION

BEFORE STARTING INSTALLATION VON DUPRIN Installation Instructions 22 Rim Device Devices covered by these instructions: 22 Rim Device 22-F Fire Exit Rim Device BEFORE STARTING INSTALLATION 1. Check hardware schedule for strikes, fasteners,

More information

CONCEALED VERTICAL ROD PANIC EXIT DEVICE

CONCEALED VERTICAL ROD PANIC EXIT DEVICE INSTALLATION INSTRUCTIONS CRL JACKSON 1085-1085P CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com 11M0236 ORDER OF

More information

TOOLS REQUIRED Metal Wood Wood and Metal Screws. #16 Drill #12-24 Tap. 1/8 Drill

TOOLS REQUIRED Metal Wood Wood and Metal Screws. #16 Drill #12-24 Tap. 1/8 Drill DEVICES COVERED IN THIS DOCUMENT: 4700S Surface Vertical Rod Device 4700SF Fire Exit Surface Vertical Rod Device TOOLS REQUIRED Metal Wood Wood and Metal Screws Sex Bolts #7 Drill ¼ -20 Tap #16 Drill #12-24

More information

33/3547A. Special tools needed: #10-24 tap Drill bits: #25, 5/16, 13/32, 1/2

33/3547A. Special tools needed: #10-24 tap Drill bits: #25, 5/16, 13/32, 1/2 911404-00 Concealed Vertical Rod Exit Device 33/3547A Installation Instructions Devices covered by these instructions: 33/3547A and 33/3548A Concealed Vertical Rod Exit Device 33/3547A-F and 33/3548A-F

More information

33/3527A. Devices covered by these instructions: 33/3527A-F (Fire) Surface Vertical Rod Exit Device

33/3527A. Devices covered by these instructions: 33/3527A-F (Fire) Surface Vertical Rod Exit Device *911403-00* 911403-00 Surface Vertical Rod Exit Device 33/3527A Installation Instructions Devices covered by these instructions: 33/3527A Surface Vertical Rod Exit Device 33/3527A-F (Fire) Surface Vertical

More information

1530(F) Mortise Exit Devices Installation Instructions

1530(F) Mortise Exit Devices Installation Instructions 1530(F) Mortise Exit Devices Installation Instructions Singe Doors or Pairs (2) 12-12-24 PFHUM/WS 798 Universal Strike Standard Device Package Devices are packed ready for application reinforced metal

More information

Note: The dimensions of the Template are shown in inches. See attached page for the Metric Conversion Table for millimeters.

Note: The dimensions of the Template are shown in inches. See attached page for the Metric Conversion Table for millimeters. 801 Avenida Acaso, Camarillo, Ca. 93012 (805) 494-0622 www.sdcsecurity.com E-mail: service@sdcsecurity.com These instructions are presented a in step by step sequence. Please read it through before installation.

More information

* * 98/9950WDC. Fire-Rated Devices include these. additional components. 1-Point Latch (LBL)

* * 98/9950WDC. Fire-Rated Devices include these. additional components. 1-Point Latch (LBL) *24739468* 24739468 98/9950WDC Installation Instructions 1-Point Latch (LBL) Fire-Rated Devices include these additional components Metal Edge Wrap required for 60 and 90-minute applications 2-Point Latch

More information

Congratulations! You are now on your way to enriching your life with!

Congratulations! You are now on your way to enriching your life with! C) Using the base point as your reference, measure up 8-1/32 and mark a horizontal line. Measure in from the edge of the door the distance of your backset and mark where the two lines cross. This will

More information

Active Push Bar. Safety glasses Measuring tape Level Pencil Power drill Drill bits: 5/32, 3/4 Center punch Phillips screw driver

Active Push Bar. Safety glasses Measuring tape Level Pencil Power drill Drill bits: 5/32, 3/4 Center punch Phillips screw driver EX88 Interlocking Rim Exit Device Preparation Guide and Installation Instructions Box Contents EX88 Interlocking Rim Exit Device Back Bar Filler Plate Active Push Bar Cylinder and Trim Interface Kit Mounting

More information

LATCHBOLT FILLER PLATE ASA FILLER PLATE A. SINGLE DOOR B. DOUBLE DOOR WITH MULLION C. DOUBLE DOOR WITHOUT MULLION END COVER MOUNTING BRACKET

LATCHBOLT FILLER PLATE ASA FILLER PLATE A. SINGLE DOOR B. DOUBLE DOOR WITH MULLION C. DOUBLE DOOR WITHOUT MULLION END COVER MOUNTING BRACKET F2000R 2012.03 1/4 x1 1/2 (9 PCS) SELF TAPPING MACHINE SCREWS 1/4-20P x 3/4 (3 PCS) 1/4-20P x 3/4 (6 PCS) ROUND HEAD MACHINE SCREWS THRU BOLT (6 PCS) END COVER MOUNTING BRACKET 1/4 x 1 1/4 (3 PCS) 1/4

More information

INSTRUCTIONS FOR HIT LOCK MORTISER

INSTRUCTIONS FOR HIT LOCK MORTISER 1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-66-200 LOCK MORTISER WHEN USING POWER TOOLS ALWAYS WEAR EYE AND EAR

More information

98/9927. Devices covered by these instructions: Surface Vertical Rod Exit Device

98/9927. Devices covered by these instructions: Surface Vertical Rod Exit Device 911375-00 Surface Vertical Rod Exit Device 98/9927 Installation Instructions Devices covered by these instructions: 98/9927 Surface Vertical Rod Exit Device 98/9927-F (Fire) Surface Vertical Rod Exit Device

More information

Installation Instructions for 45HW & 47HW Electrified Mortise Locks

Installation Instructions for 45HW & 47HW Electrified Mortise Locks Installation Instructions for 45HW & 47HW Electrified Mortise Locks Contents These installation instructions describe how to install your 45HW & 47HW Electrified Mortise Lock. Topics covered include: Finishing

More information

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

Installation Instructions

Installation Instructions for s TOC Table of Contents 1 Mortise Lock Handing Instructions.... 2 2 3 4 5 Mortise Lock Door Preparation & Installation... 3 HSS Trim Installation.... 5 Knob x Knob...6 Lever x Knob....7 Turn-Piece

More information

Door Hardware Installation Instructions. Version A No Interior on an Un-prepped Door Step 1 Select the Position of the Handleset

Door Hardware Installation Instructions. Version A No Interior on an Un-prepped Door Step 1 Select the Position of the Handleset For Assistance Call: 1-800-522-7336 8 am - 5 pm, Monday - Friday, MST or visit our Website at: www.grandeur-nw.com Door Hardware Installation Instructions Dummy Handleset Optional Rosette (Round) Interior

More information

4600 Series Rim Narrow Stile Exit Device Installation Instructions I-ED01162

4600 Series Rim Narrow Stile Exit Device Installation Instructions I-ED01162 DEVICES COVERED IN THIS DOCUMENT: 4600 Series Rim Panic Narrow Stile Exit Device 4600 Series Rim Fire Narrow Stile Exit Device OVERVIEW Outside of Door RHR LHR Inside of Door APPLICATIONS 4950 BLADE STOP

More information

Hardware Installation. Do this first:

Hardware Installation. Do this first: 1 Do this first: Hardware Installation Need some help? Here s what you ll need: 4 AA Batteries Phillips screwdriver Visit us online. support.remotelock.com We re here to help. 1 (877) 254 5625 support@remotelock.com

More information

6625 WEST WILSHIRE BLVD. OKLAHOMA CITY, OK (405) FAX (405)

6625 WEST WILSHIRE BLVD. OKLAHOMA CITY, OK (405) FAX (405) INSTALLATION INSTRUCTIONS FOR THE TAILGATE WITH LATCH AND LINK ASSEMBLY 76-87 FORD SHORT & 53-87 FORD LONG FLARESIDES 1. Assemble the bed and make sure the box is square. Measure the distance between the

More information

How To Measure Your Finished Opening

How To Measure Your Finished Opening 3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips

More information

INSTALLATION INSTRUCTIONS CRL JACKSON

INSTALLATION INSTRUCTIONS CRL JACKSON INSTALLATION INSTRUCTIONS CRL JACKSON 2085 CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com 11M0250 ORDER OF ASSEMBLY

More information

MORTISE LOCK INSTALLATION INSTRUCTIONS

MORTISE LOCK INSTALLATION INSTRUCTIONS MORTISE LOCK INSTALLATION INSTRUCTIONS INSPIRE TM ROSELESS DESIGNER TRIM FM 340 Rev. 10/18 TABLE OF CONTENTS: DOOR PREPARATION 1 ML2000 LOCK HANDING 2 FULL WORKING TRIM (STD) 3 HALF WORKING TRIM (M30)

More information

Stage 2: Preparing the door (read in conjunction with Hole Drilling Options on back of Template).

Stage 2: Preparing the door (read in conjunction with Hole Drilling Options on back of Template). There are three stages to fitting the CL100 mortise case: Stage 1: Marking out the position of the lock. Stage 2: Preparing the door by mortising and drilling holes. Stage 3: Fitting lock, door furniture,

More information

Sliding Glass Door Assembly and Installation Guide

Sliding Glass Door Assembly and Installation Guide Sliding Glass Door Assembly and Installation Guide Index Door System Components and Hardware The following components are needed to complete the installation of your Sliding Patio Door unit. Check all

More information

Installation Instructions for Trilock Omni BB Twin Pull Handle Version - Suits 35mm to 45mm door thickness

Installation Instructions for Trilock Omni BB Twin Pull Handle Version - Suits 35mm to 45mm door thickness Installation Instructions for Trilock Omni BB Twin Pull Handle Version - Suits 35mm to 45mm door thickness Step 1. Fold template where indicated. Position template on door edge at desired lock / latch

More information

Installation Instructions

Installation Instructions VON DUPRIN Installation Instructions 98/9947WDC Concealed Vertical Rod Exit Device Wood Door Applications Devices covered by these instructions: 98/9947WDC Concealed Vertical Rod Device 98/9947WDC-F (Fire)

More information

WOOD DOOR INSTALLATION

WOOD DOOR INSTALLATION 1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-32VD9W TEMPLATE FOR VON DUPRIN 99 RIM WOOD DOOR INSTALLATION WHEN USING

More information

Shetland Stalls Installation Instructions

Shetland Stalls Installation Instructions Shetland Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 1/9/18 Before you start Kit can accommodate up to 12 wide stall front

More information

33/35A Series. Devices covered by these instructions: Rim Exit Device. CD33/35A Rim Exit Device EL33/35A Rim Exit Device SS33/35A Rim Exit Device

33/35A Series. Devices covered by these instructions: Rim Exit Device. CD33/35A Rim Exit Device EL33/35A Rim Exit Device SS33/35A Rim Exit Device 911402-00 Rim Exit Device 33/35A Series Installation Instructions Devices covered by these instructions: 33/35A Rim Exit Device CD33/35A Rim Exit Device EL33/35A Rim Exit Device SS33/35A Rim Exit Device

More information

NARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE. Installation Instructions

NARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE. Installation Instructions NARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE Installation Instructions PART Y015 JUNE 2016 Table of Contents Section 1. GENERAL NOTES AND GUIDELINES... 2. DOOR HARDWARE A. Locks B. Push/Pulls

More information

Atrium Patio Door Field Service Manual

Atrium Patio Door Field Service Manual Atrium Patio Door Field Service Manual December 2005 Table of contents Service Agreement Pg 2 Release Agreement Pg 5 Inspection form Pg 6 Warranty Pg 8 Replacing swing panel Pg 12 Replacing sliding panel

More information

Installation Instructions for 45H & 47H Mortise Locks

Installation Instructions for 45H & 47H Mortise Locks Installation Instructions for 45H & 47H Mortise Locks Contents These installation instructions describe how to install your 45H & 47H Mortise Lock. Topics covered include: Finishing the preparation...

More information

CM5500 COMPUTER MANAGED MORTISE LOCK INSTALLATION MANUAL

CM5500 COMPUTER MANAGED MORTISE LOCK INSTALLATION MANUAL The 5500 series lock is a stand-alone, microprocessor controlled, electromechanical locking system. The 5500 employs a heavy-duty mechanical design with fewer moving parts that a standard mechanical mortise

More information

INSTALLATION INSTRUCTIONS CRL JACKSON

INSTALLATION INSTRUCTIONS CRL JACKSON INSTALLATION INSTRUCTIONS CRL JACKSON 1285 CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com 11M0248 ORDER OF ASSEMBLY

More information

D3976 RECESSED EXIT INSTALLATION INSTRUCTIONS

D3976 RECESSED EXIT INSTALLATION INSTRUCTIONS PACKAGE CONTENTS PRODUCT MUST BE INSTALLED ACCORDING TO ALL APPLICABLE BUILDING AND LIFE SAFETY CODES TEMPLATE INSTALLATION INSTRUCTIONS STRIKE HAND TOOL 5/32 HEX KEY ROD END CAPS EXIT DEVICE CRANK ARM

More information

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

Frameless Fixed Panel Slider

Frameless Fixed Panel Slider INSTALLATION INSTRUCTIONS Frameless Fixed Panel Slider QCI-5279 SINGLE ROLLER WITH ANTI-JUMP DOUBLE ROLLERS QCI5279 Rev Page Certified 08/09/6 Tools: To install your New Shower Enclosure, you may need

More information

8800 Series Mortise Lockset Knob, Lever, Reflections and Security Trims Installation Instructions

8800 Series Mortise Lockset Knob, Lever, Reflections and Security Trims Installation Instructions 8800 Series Mortise Lockset Knob, Lever, Reflections and Security Trims Installation Instructions IMPORTNT: The accuracy of the door preparation is critical for the proper functioning and security of this

More information

OVERVIEW. Mounting Post (2 places) Cylinder Cam. Handing Pin

OVERVIEW. Mounting Post (2 places) Cylinder Cam. Handing Pin DEVICES COVERED IN THIS DOCUMENT: 46CE Cylinder Escutcheon Key locks and 46DT Dummy Trim Pull when dogged unlocks lever 46BE Blank Escutcheon Always operable 46NL Night Latch Key retracts latchbolt 46NK

More information

Pet Door Panel Installation Manual

Pet Door Panel Installation Manual Pet Door Panel Installation Manual 400-558-1 1 4/3/03, 3:26 PM Components: Pet Door Panel Panel Latch Assembly Foam Weather-stripping Glass Sweep (4) Binding Posts (6) #6 x 1/2 Sheet Metal Screws (4) 8-32

More information

CRCODE-202. Mechanical Lock. Instruction and Programming Manual. Before Installing:

CRCODE-202. Mechanical Lock. Instruction and Programming Manual. Before Installing: CRCODE-202 Mechanical Lock Instruction and Programming Manual Before Installing: 1. Please read the instructions carefully to prevent missing important steps. *Note: Improper installations may result in

More information

Door and Jamb Preparation for Schlage Hardware LOCK SERIES INDEX OF TEMPLATE SHEETS. H-Series Locks Door Template Number

Door and Jamb Preparation for Schlage Hardware LOCK SERIES INDEX OF TEMPLATE SHEETS. H-Series Locks Door Template Number Door and Jamb Preparation for Schlage Hardware HSERIES LOCK SERIES INDEX OF TEMPLATE SHEETS Locks Door Template Number Door Edge Door Wood or Function Description Flat Bev. Thickness Composite Metal H110

More information

Melamine Plastic Laminate. Toilet Partition Installation Manual

Melamine Plastic Laminate. Toilet Partition Installation Manual Melamine Plastic Laminate Toilet Partition Installation Manual PHONE: FAX: 1-866-317-2786 ATTENTION DO NOT MIX FASTENER PACKS EACH FASTENER PACK HAS THE NECESSARY BOLTS, BARRELS AND SCREWS TO INSTALL THE

More information

INSTALLATION INSTRUCTIONS Z7800 SERIES MORTISE LOCK

INSTALLATION INSTRUCTIONS Z7800 SERIES MORTISE LOCK 801 Avenida Acaso, Camarillo, Ca. 93012 (805) 4940622 www.sdcsecurity.com Email: service@sdcsecurity.com A. Door Preparation: INSTALLATION INSTRUCTIONS Z7800 SERIES MORTISE LOCK 1. Measure desired height

More information

INSTALLATION INSTRUCTIONS CRL JACKSON

INSTALLATION INSTRUCTIONS CRL JACKSON INSTALLATION INSTRUCTIONS CRL JACKSON 3185 MID-PANEL CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com 11M0252 ORDER

More information

INSTRUCTIONS FOR HIT-45 MORTISE LOCK INSTALLATION

INSTRUCTIONS FOR HIT-45 MORTISE LOCK INSTALLATION 1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-45 MORTISE LOCK INSTALLATION WHEN USING POWER TOOLS ALWAYS WEAR EYE

More information

7110(F), 7170(F)(LBR) Surface Vertical Rod Exit Device Series Installation Instructions

7110(F), 7170(F)(LBR) Surface Vertical Rod Exit Device Series Installation Instructions 7110(F), 7170(F)(LBR) Surface Vertical Rod Exit Device Series Installation Instructions Shim (2) Supplied Strike Plate 791 Strike (3) 10-24 x 3/4 (19mm) PFHMS Strike Angle Must Engage Strike 12-24 FHPMS

More information

x2 1/4 (6mm) Floor Anchor

x2 1/4 (6mm) Floor Anchor INSTALLATION GUIDE Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Straight Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm

More information

98/ Customer Service # Dogging Key (use to lock down pushbar)

98/ Customer Service # Dogging Key (use to lock down pushbar) 911373-00 Rim Exit Device 98/99 Installation Instructions Dogging Key (use to lock down pushbar) Customer Service 1-877-671-7011 www.allegion.com/us Allegion 2014 Printed in U.S.A. 911373-00 Rev. 05/14-f

More information

SLIDING GLASS DOOR ASSEMBLY INSTRUCTION Series 680/780

SLIDING GLASS DOOR ASSEMBLY INSTRUCTION Series 680/780 10/07 M0200030 GENERAL NOTICE READING THESE INSTRUCTIONS FIRST AND FOLLOWING THE PROCEDURES IN PROPER SEQUENCE WILL REDUCE FRUSTRATION, COSTLY MISTAKES AND WASTED TIME. Protect main frame only with light

More information

Installation Manual for Metal Toilet Partitions Standard Series

Installation Manual for Metal Toilet Partitions Standard Series For Video instructions http://www.hadrian-inc.com/tech-data/installation/toilet-partitions.aspx P a g e 1 Table of Contents Page General Notes and Tools Required 3 STEP 1: Establish Floor Bracket Locations

More information

4-lite Patio Door. Installation Instructions

4-lite Patio Door. Installation Instructions 4-lite Patio Door Installation Instructions IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. Note: Only the 5-0 x 6-8

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS LAMINATED P LASTIC TOILET PArTITIONS 1540 ClassicSeries with Options IMPORTANT: Storage and Handling Information on last page. For faster, easier installation, please review these

More information

2300 BI-FOLD INSTALLATION GUIDE

2300 BI-FOLD INSTALLATION GUIDE 2300 BI-FOLD INSTALLATION GUIDE INSTALLATION INSTRUCTIONS OF MAIN FRAME Header #8 x 2½ zinc coated screws 2 1 2 Jamb Jamb 1 1 3 #8 x 2½ zinc coated screws 4 1 4 3 #8 x 2½ zinc coated screws 5 Threshold

More information

TRILENNIUM FULL SCOPE (FS) TEMPLATE INSTRUCTIONS

TRILENNIUM FULL SCOPE (FS) TEMPLATE INSTRUCTIONS Overview Parts Included in Template System: Full Scope (FS) Template Rails, with ø 2-1/8 Crossbore Guides. FS Router Carrier (for 1-3/4, 2 & 2-1/4 Doors) FS Bridges, Stops and Twist Bolts 13/16 x 5 Router

More information

Rim-Lock Door Set Installation Instructions

Rim-Lock Door Set Installation Instructions Rim-Lock Door Set Installation Instructions Let s get started Check Your Parts List Two Doorknobs with Set Screws B. Doorknob Spindle C. Rim Lock with Mounting Screws D. Keeper with Mounting Screws E.

More information

Tools Required. * When installing on a fire door, please see instructions below. *

Tools Required. * When installing on a fire door, please see instructions below. * CL615 Tubular Mortice Latch with Code Free option CL615 Tubular Mortice Latch with Code Free option Number relating to picture Item 1 Front Plate and handle * 2 Back Plate and handle * 3 Neoprene seals

More information

HIT-30 ALUMINUM DOOR SERIES OWNERS MANUAL

HIT-30 ALUMINUM DOOR SERIES OWNERS MANUAL HIT-30 ALUMINUM DOOR SERIES OWNERS MANUAL INSTALL LOCKS LATCHES LEVERS / PADDLES INDICATORS STRIKES Every Installation Is A Self-Portrait Of The Person Who Did It! Autograph Your Work With Excellence!

More information

Vinyl Sliding Glass Door Assembly Instructions

Vinyl Sliding Glass Door Assembly Instructions Vinyl Sliding Glass Door Assembly Instructions SERIES SGD 5470/5570 Para instrucciones en español, visite: http://bit.ly/pgtassemblyinstructions Parts List ITEM 4 5 6 7 8 9 0 4 5 6 7 8 SGD 5470/5570 PARTS

More information

ASSEMBLY INSTRUCTIONS MANUAL

ASSEMBLY INSTRUCTIONS MANUAL PAGE 1 OF 9 RECOMMENDED TOOLS FOR ASSEMBLY: ALLEN WRENCH (INCLUDED) BOX WRENCH (INCLUDED) PHILLIPS SCREW DRIVER (NOT INCLUDED) PARTS IN CARTON: ALLEN WRENCH SCREWS (20 EACH) ROUND HEAD SCREWS (8 EACH)

More information

EUROLINE CLASSIC PHENOLIC / EVERGREEN. Installation Instructions. Installation Instructions.

EUROLINE CLASSIC PHENOLIC / EVERGREEN. Installation Instructions. Installation Instructions. EUROLINE ASSIC PHENOLIC / EVERGREEN EUROLINE ASSIC PHENOLIC / EVERGREEN Before you begin, please note the following considerations: Safety First! Please use proper safety gear when performing any installation.

More information

*D-1030* 1 PARTS CHECK 8 REVERSING INSTRUCTIONS F-XX-C & XX-C D Customer Service. Installation Instructions. Exit Devices

*D-1030* 1 PARTS CHECK 8 REVERSING INSTRUCTIONS F-XX-C & XX-C D Customer Service. Installation Instructions. Exit Devices *D-1030* D-1030 F-XX-C & XX-C Exit Devices Installation Instructions 8 REVERSING INSTRUCTIONS TO REVERSE THE HANDING OF A (F)XX-C DEVICE NOTE: TO REVERSE TRIM, REFER TO SEPARATE INSTALLATION SHEETS. 1

More information

Installation Instructions

Installation Instructions Installation Instructions For Models: Model Number / Description File Name 1540 Classic Series P-Lam Toilet Partitions 1540.pdf 1 INSTALLATION INSTRUCTIONS LAMINATED PLASTIC TOILET PARTITIONS 1540 Classic

More information

Installation Manual Flat Track Series

Installation Manual Flat Track Series Manual Flat Track Series Contents Safety...1 Parts...2 Hardware.......................................... 2 Tools Required..................................... 4.............................................

More information

Acoustical Surfaces, Inc.

Acoustical Surfaces, Inc. RECEIVING 1. Immediately inspect shipment for damage during transit, for example: damage caused by fork lifts, stacking, water stains etc. and disclose to delivery driver prior to signing for receipt.

More information

INSTRUCTIONS FOR HIT TEMPLATE FOR CYLINDRICAL LOCK PREPS

INSTRUCTIONS FOR HIT TEMPLATE FOR CYLINDRICAL LOCK PREPS 1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-66-110 TEMPLATE FOR CYLINDRICAL LOCK PREPS WHEN USING POWER TOOLS ALWAYS

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information on last page. Review

More information

EUROLINE CLASSIC SOLID SURFACE Installation Instructions

EUROLINE CLASSIC SOLID SURFACE Installation Instructions EUROLINE ASSIC SOLID SURFACE Installation Instructions 12/01/15 EUROLINE ASSIC SOLID SURFACE Installation Instructions Before you begin, please note the following considerations: Safety First! Please use

More information

SWINGING SCREEN DOOR FIELD INSTALLATION INSTRUCTIONS

SWINGING SCREEN DOOR FIELD INSTALLATION INSTRUCTIONS SWINGING SCREEN DOOR FIELD INSTALLATION INSTRUCTIONS TABLE OF CONTENTS 1: Measuring the Opening for the Storm Door... 4 2: Securing Storm Door Hinge Side Frame into Door Frame... 6 3: Securing Storm Door

More information

ED5200S(A) Series ED5200S(A) Series x M107 Windstorm Series SecureBolt Exit Device

ED5200S(A) Series ED5200S(A) Series x M107 Windstorm Series SecureBolt Exit Device ED5200S(A) Series ED5200S(A) Series x M107 Windstorm Series SecureBolt Exit Device Installation Instructions FM532 3/11 (Single Doors or Pairs with Mullion) For Doors of Either Hand In U.S.: Corbin Russwin,

More information

33/3550AWDC. Fire-Rated Devices include these. additional. components. 1-Point Latch (LBL) Metal Edge Wrap required for 60 and 90-minute applications

33/3550AWDC. Fire-Rated Devices include these. additional. components. 1-Point Latch (LBL) Metal Edge Wrap required for 60 and 90-minute applications 24739476 33/3550AWDC nstallation nstructions 1-Point Latch (LBL) Fire-Rated Devices include these additional components Metal Edge Wrap required for 60 and 90-minute applications 2-Point Latch includes

More information

EXIT DEVICE OPERATION FIRE DOOR LABELS, STRIKES AND FRAME SCREWS FOR INFORMATION CALL OR VISIT RITEDOOR.COM

EXIT DEVICE OPERATION FIRE DOOR LABELS, STRIKES AND FRAME SCREWS FOR INFORMATION CALL OR VISIT RITEDOOR.COM RECORD & LABELS WHAT THIS OWNER'S CAN DO FOR YOU It explains exactly how The Rite Door operates. It explains periodic maintenance requirements necessary to assure reliable operation. It explains simple

More information

* * 22 & 22-F. Please give these instructions to building owner after device is installed BS EN 1125 : 2008

* * 22 & 22-F. Please give these instructions to building owner after device is installed BS EN 1125 : 2008 *911407-00* Rim device 911407-00 22 & 22-F Installation Instructions BS EN 1125 : 2008 Devices covered by these instructions: 22 Rim Exit Device 22-F Rim Fire Exit Device These instructions are presented

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLine Series 1180 DuraLine Series Class-A Fire Rated IMPORTANT: Review these instructions thoroughly prior to installation. FLOOR ANCHORED

More information

Frameless Inline Door With Return QCI5263

Frameless Inline Door With Return QCI5263 INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges

More information

MP Panic Exit Police Lock. Review Of March 2004 Installation

MP Panic Exit Police Lock. Review Of March 2004 Installation MP Panic Exit Police Lock Introduction To Installing The MP4900 Panic Exit Police Lock A little bit of knowledge before getting to the door can go along way towards simplifying the installation Bob Hart

More information

Installation Manual for Metal Toilet Partitions Elite & Elite Plus Series

Installation Manual for Metal Toilet Partitions Elite & Elite Plus Series P a g e 1 Table of Contents Page General Notes and Tools Required 3 STEP 1: Establish Floor Bracket Locations 4 STEP 2: Fasten Floor Brackets 4 & 5 STEP 3: Erect Panels 6 STEP 4: Erect Wall Pilaster 7

More information

MORTISE LOCKS LA1Tx7 //DATASHEET

MORTISE LOCKS LA1Tx7 //DATASHEET //DATASHEET SATO ocks AElement Access control requires a good, reliable door locking system. SATO offers a wide range of mortise locks in order to ensure that the door is correctly locked. Whether you

More information

No. 059FL. No. 251FL. No. 260FL. No. 305RE. Etruscan Bronze. Florentine Brass. Siena Brass (D) All designs available in these finishes.

No. 059FL. No. 251FL. No. 260FL. No. 305RE. Etruscan Bronze. Florentine Brass. Siena Brass (D) All designs available in these finishes. SINCE 1964 No. 059FL No. 251FL No. 260FL No. 305RE 2 Etruscan Bronze (ETR) Florentine Brass (D) Siena Brass (BAS) Venetian Nickel (BPS) All designs available in these finishes. No. 309RE No. 331FL No.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS www.marwincompany.com Kit Number Door Height Rough Opening Height KD200BB68 80 84 ½ KD200BB70 84 88 ½ KD200BB80 96 100 ½ INSTALLATION INSTRUCTIONS 200BB SERIES KD POCKET DOOR FRAME FOR 2 X 4 STUD WALLS

More information

Closet System Installation Manual

Closet System Installation Manual Closet System Manual Thank you For choosing our Custom Closet Collection to fit all your needs Closets come fully assembled to make your project an enjoyable and satisfying experience. With quality Custom

More information

3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS

3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS 3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. TOOLS NEEDED: Tape Measure

More information

Retractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors)

Retractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors) Retractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors) IMPORTANT: Please read before you begin. Table of Contents

More information

1. TOOLS + MATERIALS REQUIRED

1. TOOLS + MATERIALS REQUIRED R INSTALLATION INSTRUCTIONS PRODUCT: BALDUR + ODEN CONFIGURATION: BI-PARTING DOOR MOUNT: TOP MOUNT Product is covered by U.S. patents. For more information visit www.krownlab.com. TOOLS + MATERIALS REQUIRED

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last

More information

Assembly Instructions Nevins Phone Booth

Assembly Instructions Nevins Phone Booth Assembly Instructions Nevins Phone Booth Included Hardware Tools Required supplied by installer Drill & Bit Bolt A - (16) 1/4-20 x 1-1/2 hex head Bolt B - (20) 1/4-20 x 2-1/2 phillips head Screw 1 - (24)

More information