4600 Series Rim Narrow Stile Exit Device Installation Instructions I-ED01162

Size: px

Start display at page:

Download "4600 Series Rim Narrow Stile Exit Device Installation Instructions I-ED01162"

Johnathan Russell
5 years ago
Views:

1 DEVICES COVERED IN THIS DOCUMENT: 4600 Series Rim Panic Narrow Stile Exit Device 4600 Series Rim Fire Narrow Stile Exit Device OVERVIEW Outside of Door RHR LHR Inside of Door APPLICATIONS 4950 BLADE STOP STRIKE SINGLE 1 11/32" [34.1] 4920 STANDARD STRIKE SINGLE 1 21/32" [42] NARROW STILE RIM EXIT DEVICE NARROW STILE RIM EXIT DEVICE 2 1/8" [54] MIN STILE 3 1/4" [82.6] MIN STILE 4950 Blade Stop Strike Application Single Door Panic Exit Hardware 4920 Standard Strike Application Single or Double Door Panic Exit Hardware (4920F Strike Available for Fire Rated Applications) 4920 STANDARD STRIKE AND MULLION 1 21/32" [42] 2" [51] MULLION 1 21/32" [42] NARROW STILE RIM EXIT DEVICE NARROW STILE RIM EXIT DEVICE 4920 Standard Strike Application Single or Double Door Panic Exit Hardware (4912 strike available for fire rated applications) 3 3/4" [95] MIN STILE Page 1 of 8

2 4952 SEMI-FLUSH STRIKE AND MULLION 4950 BLADE STOP STRIKE AND MULLION 31/32" [25] 2" [51] MULLION 31/32" [25] 1 11/32" [34] 2" [51] MULLION 1 11/32" [34] NARROW STILE RIM EXIT DEVICE NARROW STILE RIM EXIT DEVICE NARROW STILE RIM EXIT DEVICE NARROW STILE RIM EXIT DEVICE 4952 Semi-Flush Strike Application Single or Double Door Panic Exit Hardware 2 3/4" [70] MIN STILE 3 1/4" [83] MIN STILE 4950 Blade Stop Strike Application Single or Double Door Panic Exit Hardware COMPONENT PARTS End Cap Bracket Dogging Device (Only on panic hardware) Chassis Device Body End Cap Dogging Wrench (Panic device only) 4950 Panic Blade Stop Strike (Provided with Panic Device) Head Cover 4965 PANIC EXIT DEVICE SHOWN (FIRE RATED DEVICE AVAILABLE) 4920 Panic Standard Strike (Purchased Separately) TOOLS REQUIRED 4920F Fire Rated Standard Strike (Provided with Fire Rated Device) 4952 Panic Semi-Flush Strike (Purchased separately) Metal Wood Wood and Metal Screws Sex Bolts #7 #25 5/16 1/2 3/4 1/4-20 #10-24 Page 2 of 8 1/8 5/16 1/2 3/4 For wood doors, drill 1/8 hole Machine Screws #7 drill, 1/4-20 tap Drill 5/16 thru from device side. Drill 3/8 from other side (pull side). Check building and fire codes to see if your application requires the use of sleeve nuts and bolts.

3 1. MARK A. Measure and draw center line on door and frame, typically 40 from finished floor. B. Fold and apply templates to door and frame. C. Templates include: T-ED Blade Stop Strike Template T-ED /4920F Standard Strike Template T-ED Semi-Flush Strike Template T-ED RIM Cylinder Only Template LHR Shown (RHR opposite) C L 40" 1016 TO FINISHED FLOOR 2. DRILL MOUNTING HOLES A. Mark, drill, and tap holes as shown on door and frame templates. Do not drill center hole on strike until after strike has been mounted and adjusted at the end of the installation. Strike Mounting Holes Exit Device Mounting Holes (2 Places): Metal Door: Drill/Tap for 1/4"-20 Screws Wood Door: Pre-Drill 1/8" holes Sex Bolts: 5/16" Clearance hole on push side 3/8" Clearance Hole on pull side Trim: 5/16" Clearance hole on push side 1/2" Clearance Hole on pull side Remove section of blade stop, see template for details. (Only for Blade Stop) Trim tailpiece Hole: (Only required if using trim) 1/2" Clearance hole on push side 3/4" Clearance hole on pull side BLADE STOP FRAME & NARROW STILE SHOWN ABOVE Page 3 of 8

4 3. INSTALL STRIKE A. Install strike using the two outer mounting holes Blade Stop Strike Install: 1 11/32" 34 1/2" 13 15/16" 24 B 2 5/8" 67 A 2 1/32" 52 C 2 7/8" 73 Blade Stop D Door Drill and tap for #10-24 Screws 4920 Standard Strike Install: A. B. Do not drill center hole until final adjustment at the end of the installation. Align front edge of strike with door side of stop. Blade Stop Door Stile C: Trim Tailpiece clearance hole: 1/2" Push Side 3/4" Pull Side (Only required if using trim) D: Device Mounting Holes (2 Places): Metal Door: Drill/Tap for 1/4"-20 Screws. Wood Door: Pre-Drill 1/8" holes. Sex Bolts: 5/16" Clearance hole on push side, 3/8" Clearance hole on pull side. Stop Face 1 3/32" 27.8 From Door Face 27/32" /32" 42 From Stop Face 2 5/8" 66.7 A B 2 7/8" 73 C Standard Door Drill and tap for 1/4"-20 Screws A: Do not drill center hole until final adjustment at the end of the installation. Door Stile B: Trim Tailpiece clearance hole: 1/2" Push Side 3/4" Pull Side (Only required if using trim) C: Device Mounting Holes (2 Places): Metal Door: Drill/Tap for 1/4"-20 Screws Wood Door: Pre-Drill 1/8" holes Sex Bolts: 5/16" Clearance hole on push side, 3/8" Clearance hole on pull side. Page 4 of 8

5 3. INSTALL STRIKE (CONTINUED) 4952 Semi-Flush Strike Install: 3/16" /4" /32" 35.7 From Door Face C 31/32" /2" /8" 66.7 A 2 7/8" 72.9 B Mullion/ Door Mullion/ Drill and tap for #10-24 Screws A: Trim Tailpiece clearance hole 1/2" Push Side 3/4" Pull Side (Only required if using trim) B: Semi-Flush Strike Door Stile C: Device Mounting Holes (2 Places): Metal Door: Drill/Tap for 1/4"-20 Screws. Wood Door: Pre-Drill 1/8" holes. Sex Bolts: 5/16" Clearance holes on push side, 3/8" Clearance holes on pull side. 4. INSTALL 4950 WEAR STRIP (SKIP IF USING A DIFFERENT STRIKE) A. Place wear strip on frame and center on strike. B. Hold in place and mark all 4 hole locations. C. Drill 1/8 dia. Holes in 4 places and install wear strip with flat head drive rivets (provided). Flat Head Rivets Wear Strip Door Side of Blade Stop Page 5 of 8

6 5. CUT EXIT DEVICE TO LENGTH A. Remove head cover from exit device chassis. B. Align device with mounting holes and measure to determine length to cut device. The minimum clearance between the frame stop and end of exit device (with end cap removed) is 1-5/8. C. Cut device square with hack saw or metal cutting saw blade and deburr edges. Be sure to save the spring clip on the dogging plate cover for use on the device. Stop Align device with mounting holes or temporarily secure with mounting screws. 1 5/8" [41] Minimum Clearance (Note A) A. Minimum clearance is measured from the frame stop to the end of the device (without end cap). Save spring clip from cut portion and reinstall at the end of device body. 6. INSTALL DEVICE A. Mount exit device using the provided screws. If using trim, be sure to line up trim actuating shaft (tailpiece) with cam located on back of exit device chassis. Sex Bolts provided for through door mounting using 1/4-20 screws. Mounting with trim: Be sure to line up trim actuating shaft (tailpiece) with cam on back of device. Mounting to door: Metal: Drill/Tap for 1/4-20 Machine Screws Wood: #12 Wood Screws (Pre-Drill 1/8" holes) Page 6 of 8

7 7. INSTALL END CAP A. Remove end cap from end cap bracket. B. Mark hole locations by either using template or holding end cap bracket up against door and device. Be sure exit device is level before inserting end cap bracket lip into end of device. C. Mark and drill/tap holes. D. Install end cap bracket and end cap. 5/8" Wire routing hole provided in end cap. 8. TEST AND ADJUST Mounting to door: Metal: Drill/Tap for 1/4"-20 Machine Screw Wood: Pre-Drill 1/8" hole for #12 Wood Screw Sex Bolt: 5/16" clearance hole on push side 3/8" clearance hole on pull side A. Check engagement between device and strike. Shim strike as needed for a 9/32 clearance between strike and chassis. B. Check opening and closing door. Repeat this with head cover to make sure head cover does not hit the strike. C. If device operates properly, drill/tap and install center screw in strike (if applicable). Add shim if needed. 9/32" +/- 1/32" [7+/- 0.8] Target Clearance Target Clearance measured from strike face to front edge of device chassis (Blade Stop Application Shown Above) Page 7 of 8

8 9. INSTALL COVERS A. Install head cover on chassis using provided screws. Head Cover mounting screws provided (4 places) Install head cover on device chassis. 10. DOG DEVICE For increasing the life of this device, dog device down during high traf periods of the day. (A dogging device is not available on re rated models.) HEX WRENCH DOGGING Dogging: Depress push bar, insert dogging hex wrench, and turn clockwise 35 degrees. The push bar will remain depressed and the latch will stay retracted. Release Dogging: Hold push bar, insert dogging hex wrench, and turn counterclockwise 35 degrees. The push bar will return to the up position and latch will extend to lock door. CYLINDER DOGGING For cylinder dogging, remove cover plate. Remove the hex wrench extension located below the dogging cover plate, which is held in place by a magnet. Install a mortise cylinder into the cylinder dogging cover plate using an 11/32 (8.7 mm) solid cylinder collar and cash box nut. On the mortise cylinder, use a standard cam (.723 [18 mm], screw center to tip of cam). The cylinder should be oriented so the cam is pointing away from the exit device push bar. Install the dogging cover plate with cylinder and test dogging. Depress the push bar, insert key, and turn key clockwise to dog device. Turn key counterclockwise to release dogging. Required hardware for cylinder dogging: One (1) mortise cylinder, lengths 1-1/8, 1-1/4, or 1-3/8, one (1) standard cam.723 (18 mm) screw center to top of cam, one (1) 11/32 (8.7 mm) stock solid collar, one (1) cash box nut, and one (1) Hager cylinder dogging kit. Page 8 of 8

33/35A Series. Devices covered by these instructions: Rim Exit Device. CD33/35A Rim Exit Device EL33/35A Rim Exit Device SS33/35A Rim Exit Device

33/35A Series. Devices covered by these instructions: Rim Exit Device. CD33/35A Rim Exit Device EL33/35A Rim Exit Device SS33/35A Rim Exit Device 911402-00 Rim Exit Device 33/35A Series Installation Instructions Devices covered by these instructions: 33/35A Rim Exit Device CD33/35A Rim Exit Device EL33/35A Rim Exit Device SS33/35A Rim Exit Device