Installation Instructions For The 8850FL Series Mortise eboss

Transcription

1 Installation Instructions For The 8850FL Series Mortise eboss Electronic Battery Operated Security Solution FEATURES Battery Operated (Hardwire Capable) Motorized Grade 1 Mortise Lock 94 User Code Capacity All Metal and Pushbuttons LED Function Indicator Weather Resistant, ADA Compliant 12-Button Keypad Modular Design (Simple Installation) Audible Pushbutton Patent Pending Keypad Blinders Request to Enter Input Emergency, Supervisor, Passage, Lockout and Master Codes Deadbolt Monitoring Feature for Deadbolt Applications (8852FL & 8853FL). Operational Modes Secure Normal locked state. Any assigned user code can gain access. Lock relocks automatically. Lockout Lockset will not accept any assigned user codes except for the Supervisor and Emergency Codes. Passage Maintains unlocked state. Relocks by entering passage code the second time Rev. B Yale Commercial Locks & Hardware 100 Yale Avenue Lenoir City, TN Product Support Tel Fax Yale is a registered trademark of Yale Security Inc. Other products brand names may be trademarks or registered trademarks of their respective owners and are mentioned for reference purposes only. These materials are protected under US copyright laws. All contents current at time of publication. Yale Security Inc. reserves the right to change availability of any item in this manual, its design, construction and/or its material. Copyright 2005 Yale Security Inc. All rights reserved.

2 Table of Contents Section I List of components A. Necessary Tools... 2 B. Non-Deadbolt functions 8850FL-8851FL C. Deadbolt functions 8852FL-8853FL Section II Prepare the door A. Determine hand of door B. Mark centerline for lever position and door template... 5 C. Drill holes in door D. Mark frame for strike mortise cavity E. Drill mortise cavities in door and frame F. Install strike ,6 Section III Handing the Mortise Lock A. Handing the latchbolt B. Handing the hubs Section IV Installing Assembly on Door 8850FL & 8852FL A. Installing keypad, long escutcheon and controller board B. Installing lockbody, short escutcheon and levers FL & 8853FL C. Installing keypad and controller board D. Installing lockbody, large escutcheon, small escutcheon and levers FL, 8851FL, 8852FL, 8853FL E. Installing the battery escutcheon and adjusting for appearance.. 13 F. Tightening the cylinder (if needed) and installing the armor front G. Template for drilling a mortise pocket on the edge of a door Section V Hardwire Options Diagram A. Hardwire options diagram Section I List of Components I-A Necessary tools #2 Phillips screwdriver #3 Phillips screwdriver 1/8 Allen wrench Small flat blade screw driver Hole saw set 2

3 I-B Non-Deadbolt Functions 8850FL Less Cylinder 8851FL With Cylinder SCREW PACK DESCRIPTION Qty 1/4½ TEE NUT 1 or #10-32 X 1½ 2 (FOR THICKER DOORS) #8-32 X 5/16½ BATTERY 1 #8-32 X 3/4½ ESC SCREWS 1 O/S Long W/ Cylinder O/S Long W/O Cylinder Battery #10-24 X 1-1/4½ 1 #10-24 X 2½ 1 (2-1/4 FOR THICKER DOORS) LONG PLASTIC SPACER 1 SHORT PLASTIC SPACER 1 STRIKE PACK I/S Short Keypad Assembly Controller Board DESCRIPTION Qty STRIKE 1 Mortise Lockbody Cylinder Grounding Strip Spindle Asm Cylinder Chart Door Cylinder Thickness Size 1-3/4½ 1-3/4½ 2½ 1-3/4½ 2-1/4½ 2½ ARMOR 1 FRONT COMBINATION 4 SCREW ARMOR 2 FRONT SCREW 3

4 I-C Deadbolt Functions 8852FL Less Cylinder 8853FL With Cylinder SCREW PACK DESCRIPTION Qty or O/S Long W/ Cylinder O/S Long W/O Cylinder Battery I/S Short Keypad Assembly Controller Board STRIKE PACK DESCRIPTION Qty STRIKE 1 Mortise Lockbody Cylinder Grounding Strip Spindle Asm Cylinder Chart Door Cylinder Thickness Size 1-3/4½ 1-3/4½ 2½ 1-3/4½ 2-1/4½ 2½ ARMOR 1 FRONT COMBINATION 4 SCREW ARMOR 2 FRONT SCREW 4

5 Section II Prepare the Door A) Determine hand of door Face the door a from the outside to determine its hand. Please note the outside is either the key side of an entrance door or the corridor side of a room door. The outside of a single communication door is the side opposing the hinges. The outside of a twin communicating doors is the space between the doors. B) Mark centerline for lever position and door template 1. Draw a horizontal centerline for the lock lever/spindle on both sides of door at desired height above finished floor line. Standard height for horizontal centerline is 39-15/16½ above finished floor. 2. Compare the lock function number being installed with hole chart (See Template) to determine the holes to be marked. 3. Position the installation template on the door so that the horizontal centerline lines up with the marked horizontal line on the door, and the desired edge of the template lines up with the edge of the door. 4. Mark the holes to be drilled using a scribe, center punch, or nail on the inside and outside of door. To avoid shifting of the template, it may be taped to the door during this step. C) Drill holes in door 1. Bore marked trim holes (step B4). To avoid splintering wood, bore thru holes from both sides of door. D) Mark frame for strike mortise cavities 1. Mark the vertical position of strike on jamb using the reference centerline on installation template. Mark location of strike lip.(first DETERMINE IF SILENCERS ARE TO BE USED) To locate horizontal centerline of strike, take half the door thickness PLUS the thickness of silencer (if used). Use this dimension to locate the strike centerline from the doorstop. (See Fig. 1, page 6) E) Drill Mortise Cavities in door and frame 1. Align mortise pocket template on edge of door using the spindle height mark. 2. Mark door edge for lock body attaching screws and mortise pocket. 3. Mortise door edge for lock body 4½½ deep. See page 14 for Template. 4. Drill pilot holes for attaching screws. 5. Slide lock body into cavity and attach using the combination attaching screw. Install armor front and use as template. Mark outline. 6. Mortise door edge for lock front (7/32 ½) deep. 7. Mortise jamb for strike (3/32½ deep). Be sure to mortise 1 ½ (25mm) deep to accommodate lock bolts or strike F) Install Strike 1. Attach strike to jamb using two #12 combination attaching screws. (See Fig. 1, page 6). 5

6 Section II Prepare the Door (CONTINUED) Combination screws Combination screws A/F Lever (Fig.1) 8800 Series Strike Shown (Fig.2) 8800 Series Lock Shown 6

7 Section III Handing the Mortise Lock III-A Handing the Latchbolt Plate Holes Plate Push Here Step 1. Locate plate in either of the plate holes. Step 2. Exploded view of plate where screw driver presses. Step 3. Insert screw driver in hole. press on plate while pulling out latchbolt. Step 4. Rotate latchbolt 180 to desired handing position. Step 5. Firmly press latchbolt into case until it stops moving. Step 6. Check if latchbolt operates properly. Push and pull on latchbolt a few times. Latchbolt should NOT be able to rotate. 7

8 Section III-B Handing the Hubs NOTE: (Red mark should always face towards the outside of door) Locking Piece Square Spindle Hole Step 1. Find red mark on locking piece. Step 2. Move toggle button slide away from square spindle hole. Step 3. Push on edge of locking piece between locking piece and square spindle hole. Rotate 180. Red mark indicates locked side of door and MUST be seen on one side of lock. 8

9 Section IV Installing Assembly on Door IV-A Installing Keypad, Long and Controller Board Non-Cylinder Applications 8850FL & 8852FL Controller Board for 8850FL Controller Board for 8852FL G 3 4 H 6 E A 5 Tee Nut Install thru hole I see template 2 D 7 Grounding Strip Steps 1. Install keypad housing: a) Route keypad harness thru hole E, all the way thru door. b) Route keypad post thru hole G. 2. Install O/S long escutcheon posts in holes D and H. This will hole the keypad in place. 3. Install short plastic spacer with flat down in hole H on inside of door. 4. Securely fasten the #10-24 X 1-1/4½ screw thru the short plastic spacer. 5. Install the tee nut from the inside of the mortise pocket thru hole I. See template. 6. Install long plastic spacer with flat up in the back of the controller board. 7. Secure grounding strip to door making sure the strip connects the controller board to the I/S Short Esc. 8. Loosely fasten the controller board to the tee nut using #10-32 X 1½ screw thru the long plastic spacer. 9. Loosely fasten the top of the controller board using #10-32 X 1½ screw thru hole G. 9

10 IV-B Installing lockbody, short escutcheon and levers Non-Cylinder Applications 8850FL & 8852FL REMOVE REMOVE BEFORE USE USE See picture for connecting to circuit board Keypad connector 9 Lockbody motor A E D 10 Grounding Strip Steps 9. Route all lockbody harnesses thru the mortise pocket and thru hole E. 10. Loosely fasten lockbody to door using combination screws. 11. Install I/S short escutcheon by loosely attaching the #10-24 X 2½ screw thru hole D and to the post of the O/S long escutcheon. 12. Installing the spindle assembly thru the lock. Loosen the set screw on the inside lever and remove inside lever before installing thru lock. Be sure that the lever on the pinned end of the assembly goes on the outside of the door and the ramp of the inside spindle goes towards the set screw on the inside lever. 13. Install the inside lever and securely tighten the set screw. 14. Install harness connectors to the controller board (see Wiring Diagram on page 14). 15. Skip to page

11 IV-C Installing keypad and controller board Cylinder Applications 8851FL & 8853FL Controller Board for 8851FL Controller Board for 8853FL G 1 4 H E B 3 Install thru hole I see template Route keypad wire/connector through controller Board housing A D 5 Grounding Strip Steps 1. Install keypad housing: a) Route keypad harness thru hole E, all the way thru door b) Route keypad post thru hole G. 2. Loosely fasten the #10-32 X 1½ screw thru hole G and into the keypad post. 3. Install the tee nut from the inside of the mortise pocket thru hole I. See template. 4. Install the long plastic spacer (with flat any orientation) in the back of the controller board. 5. Secure grounding strip to door making sure the strip connects the controller board to the I/S Short Esc. 6. Loosely fasten the controller board to the tee nut using #10-32 X 1½ screw thru the long plastic spacer. 7. Loosely fasten the #10-32 X 1½ screw thru hole G and into the keypad post. 11

12 IV-D Installing lockbody, short escutcheon and levers Cylinder Applications 8851FL & 8853FL Connect to deadbolt monitoring connector from lock 9 8 REMOVE REMOVE BEFORE USE USE 6 See picture for connecting to circuit board Keypad connector Lockbody motor Deadbolt monitoring 7 10 Grounding Strip Steps 6. Route all lockbody harnesses thru the mortise pocket and thru hole E. 7. Loosely fasten lockbody to door using combination screws. 8. Install the bottom post of O/S long escutcheon thru hole D and attach the cylinder to the lockbody thru hole B. 9. Install the I/S short escutcheon by loosely fastening the #10-24 X 2½ screws thru hole D and to the post of the O/S long escutcheon. 10. Installing the spindle assembly thru the lock. Loosen the set screw on the inside lever and remove inside lever before installing thru lock. Be sure that the lever on the pinned end of the assembly goes on the outside of the door and the ramp of the inside spindle goes towards the set screw on the inside lever. 10. Install the inside lever and securely tighten the set screw. 11. Install harness connectors to the controller board (See Wiring Diagram on p 14). For deadbolt monitoring connection see picture above. 12. Skip to page

13 IV-E Installing the battery escutcheon and adjusting for appearance All Applications 2 Minimize gap between keypad and escutcheon by gently pushing them together, then tighten both controller board screws. Installing the Battery and minimizing the clearance between the Battery and the Small Rose. 1. **Dry fit the Battery to the Small Rose. NOTE: IT IS VERY IMPORTANT TO KEEP WIRES FROM GETTING PINCHED WHILE ATTACHING BATTERY COVER. 2. Check the clearance where the two meet, see top picture. If the clearance is acceptable tighten the Battery screw. **Hook **Battery 1 Battery Screw 3. If the clearance is too great loosen the Small Rose screw then push up and re-tighten the screw. Recheck clearance. If the clearance is still not acceptable remove Battery and loosen the two Controller Board screws and adjust the controller board up or down. Re-tighten controller board screws and refer to step #2. 3 Small Rose and Screw ** Battery has a machined slot that engages the hook at the top of the Controller Board prior to mating up with Rose. 13

14 IV-F Tightening the cylinder (if needed) and installing the armor front Tighten cylinder thru this hole Align the cylinder face to desired orientation and tighted the cylinder thru the hole indicatied above. 2. Securely fasten the lockbody screws. 3. Install the armor front with the 2 #10 x 21 5/16 screws provided. 4. Fasten battery cover screw. 2 3 Section V WIRING DIAGRAM V-A Wiring diagram Lockbody motor Keypad connector Remote Entry Input P/n: Normally Open Momentary Switch NO C Hardwiring Harnesses 9VDC Power input 784 (9 Volt Power Supply) 14

15 IV-G Template for drilling a mortise pocket on the edge of the door 1 3/4" 1 1/4" Ø 1-1/16 X 4.5½ DEEP Finish Care This lockset is designed to provide the highest standard of product quality and performance. Care should be taken to insure a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing. Centerline of lockbody Centerline of spindle 15