(Wood Door and Frame)
|
|
- Crystal Carr
- 5 years ago
- Views:
Transcription
1 ITS961 and ITS965 Closer in Door Track in Frame (Wood Door and Frame) 1 (REFERENCE UNIT CARTON FOR ACCESSORIES AND OPTIONS SUPPLIED) Determine hand of door. Prepare door and frame according to template for ITS961 or ITS965. If 000 accessory track brackets are used, refer to appropriate template. Adjust spring tension. CRITICAL NOTE: Clockwise turns increase spring tension. NOTE: MAXIMUM NUMBER OF TURNS 17 5MM HEX WRENCH BARRIERFREE OPENINGS Adjust only if more tension is required to close and latch the door. Depending on opening conditions, a door adjusted to meet barrierfree forces may not have sufficient power to reliably close and latch the door. NONBARRIERFREE OPENINGS Adjust according to chart. LEFT HAND DOOR RIGHT HAND DOOR The ITS 96 is UL listed for use on fire doors. Refer to door and frame manufacturer to determine if preperation is listed for fire door applications. FULL TURNS MAXIMUM FULL TURNS OF SPRING OF SPRING DOOR WT. ADJUSTER ADJUSTER (LBS) ITS961 ITS965 '6" 100 '0" '6" '0" DOOR WIDTH (INTERIOR) SPRING SIZE Thread screw a few turns into the deadstop block. Insert components into track as shown. Fasten track to frame. DEADSTOP BLOCK SLIDE SHOE TRACK BRACKETS (OPTIONAL) Part No. 000 DEADSTOP ASSEMBLY HINGE HOLD OPEN (OPTIONAL) NOTE: ARROWS ON HOLD OPEN AND SLIDE SHOE, MUST POINT AWAY FROM HINGE WHEN INSTALLING IN TRACK. Place arm on closer according to hand of door. Secure arm with pinion screw. PINION SCREW 5mm R.H. L.H. INSPK NO Rev.06/ INS NO PAGE 1 of Rev. 0/11
2 5 Close valve by turning completely clockwise. Rotate arm 5. Adjust deadstop. Open door to desired opening between 0 and 10. Tighten deadstop block. 5 The deadstop helps to prevent damage to the door and wall when the door is opened normally. The deadstop is not abuse resistant, and cannot replace a door stop in many situations. Deadstop is adjustable between 0 and 10 maximum. 9 Adjust sweep and latch valves. 6 Attach closer to door. CAUTION: DO NOT REMOVE VALVES () () (INCREASE ONLY) 7 Align hole in arm with slide shoe and attach with screw provided. SCREW 5mm 6mm ON HOLD OPEN UNITS INS NO PAGE of Rev. 0/11
3 10 (HOLD OPEN UNITS ONLY) Set hold open. A Place the hold open mechanism in desired position. Tighten screws #1 and # securely. 1 C To enable hold open, push the white slide into the hold open mechanism. To disable hold open, pull the white slide away from hold open mechanism. M.5 ON OFF B To adjust hold open force, turn clockwise to increase force, and counter clockwise to weaken force. M.5 INS NO PAGE of Rev. 0/11
4 ITS961 AND ITS965 OHC Closer in Frame Track in Door 1 (REFERENCE UNIT CARTON FOR ACCESSORIES AND OPTIONS SUPPLIED) (Wood Door and Frame) Adjust spring tension. Determine hand of door. Prepare door and frame according to template for ITS961 or ITS965. CRITICAL NOTE: Clockwise turns increase spring tension. NOTE: MAXIMUM NUMBER OF TURNS 17 5MM HEX WRENCH LEFT HAND DOOR RIGHT HAND DOOR BARRIERFREE OPENINGS Adjust only if more tension is required to close and latch the door. Depending on opening conditions, a door adjusted to meet barrierfree forces may not have sufficient power to reliably close and latch the door. NONBARRIERFREE OPENINGS Adjust according to chart. The ITS 96 is UL listed for use on fire doors. Refer to door and frame manufacturer to determine if preperation is listed for fire door applications. FULL TURNS MAXIMUM FULL TURNS OF SPRING OF SPRING DOOR WT. ADJUSTER ADJUSTER (LBS) ITS961 ITS965 '6" 100 '0" '6" '0" DOOR WIDTH (INTERIOR) SPRING SIZE Place arm on closer according to hand of door. Attach arm with pinion screw. R.H. L.H. PINION SCREW 5mm Close valve by turning completely clockwise. Rotate arm 5 and attach closer to frame. R.H. 5 5 L.H. HINGE INSPK NO Rev.1/ INS NO PAGE 1 of Rev. 0/11
5 5 Thread screw a few turns into deadstop block. Insert components into track. Fasten track to door. 7 Open door to desired opening between 0 and 10. Tighten deadstop block. DEADSTOP BLOCK DEADSTOP ASSEMBLY SLIDE SHOE The deadstop helps to prevent damage to the door and wall when the door is opened normally. The deadstop is not abuse resistant, and cannot replace a door stop in many situations. Deadstop is adjustable between 0 and 10 maximum. Adjust sweep and latch valves. CAUTION: DO NOT REMOVE VALVES HOLD OPEN (OPTIONAL) NOTE: ARROWS ON HOLD OPEN AND SLIDE SHOE, MUST POINT AWAY FROM HINGE WHEN INSTALLING IN TRACK. () 6 Align hole in arm with slide shoe and attach with screw provided. 5mm () (INCREASE ONLY) SCREW 6mm HOLD OPEN UNITS ONLY INS NO PAGE of Rev. 0/11
6 9 (HOLD OPEN UNITS ONLY) Set hold open. A Place the hold open mechanism in desired position. Tighten screws #1 and # securely. M.5 C To enable hold open, push the white slide into the hold open mechanism. To disable hold open, pull the white slide away from hold open mechanism. 1 B To adjust hold open force, turn clockwise to increase force, and counter clockwise to weaken force. M.5 OFF ON INS NO PAGE of Rev. 0/11
7 ITS961 and ITS965 Closer in Door Track in Frame (Metal Door and Frame) 1 (REFERENCE UNIT CARTON FOR ACCESSORIES AND OPTIONS SUPPLIED) Determine hand of door. Prepare door and frame according to template for ITS961 or ITS965. If 0010 accessory track brackets are used, refer to appropriate template. LEFT HAND DOOR RIGHT HAND DOOR The ITS 96 is UL listed for use on fire doors. Refer to door and frame manufacturer to determine if preperation is listed for fire door applications. Adjust spring tension. CRITICAL NOTE: Clockwise turns increase spring tension. NOTE: MAXIMUM NUMBER OF TURNS 17 5MM HEX WRENCH BARRIERFREE OPENINGS Adjust only if more tension is required to close and latch the door. Depending on opening conditions, a door adjusted to meet barrierfree forces may not have sufficient power to reliably close and latch the door. NONBARRIERFREE OPENINGS Adjust according to chart. FULL TURNS MAXIMUM FULL TURNS DOOR WIDTH OF SPRING OF SPRING SPRING (INTERIOR) DOOR WT. ADJUSTER ADJUSTER SIZE (LBS) ITS961 ITS965 '6" 100 '0" '6" '0" Thread screw a few turns into the deadstop block. Insert components into track as shown. Fasten track to frame. DEADSTOP BLOCK SLIDE SHOE TRACK BRACKETS (OPTIONAL) Part No DEADSTOP ASSEMBLY HINGE HOLD OPEN (OPTIONAL) NOTE: ARROWS ON HOLD OPEN AND SLIDE SHOE, MUST POINT AWAY FROM HINGE WHEN INSTALLING IN TRACK. Place arm on closer according to hand of door. Secure arm with pinion screw. PINION SCREW 5mm R.H. L.H INSPK NO Rev.06/0 INS NO PAGE 1 of Rev. 0/11
8 5 Close valve by turning completely clockwise. Rotate arm 5. Adjust deadstop. Open door to desired opening between 0 and 10. Tighten deadstop block. 5 The deadstop helps to prevent damage to the door and wall when the door is opened normally. The deadstop is not abuse resistant, and cannot replace a door stop in many situations. Deadstop is adjustable between 0 and 10 maximum. 9 Adjust sweep and latch valves. 6 Attach closer to door. CAUTION: DO NOT REMOVE VALVES () () (INCREASE ONLY) 7 Align hole in arm with slide shoe and attach with screw provided. SCREW 5mm 6mm ON HOLD OPEN UNITS INS NO PAGE of Rev. 0/11
9 10 (HOLD OPEN UNITS ONLY) Set hold open. A Place the hold open mechanism in desired position. Tighten screws #1 and # securely. 1 C To enable hold open, push the white slide into the hold open mechanism. To disable hold open, pull the white slide away from hold open mechanism. M.5 ON OFF B To adjust hold open force, turn clockwise to increase force, and counter clockwise to weaken force. M.5 INS NO PAGE of Rev. 0/11
10 ITS961 AND ITS965 OHC Closer in Frame Track in Door 1 (REFERENCE UNIT CARTON FOR ACCESSORIES AND OPTIONS SUPPLIED) (Metal Door and Frame) Adjust spring tension. Determine hand of door. Prepare door and frame according to template for ITS961 or ITS965. CRITICAL NOTE: Clockwise turns increase spring tension. NOTE: MAXIMUM NUMBER OF TURNS 17 5MM HEX WRENCH LEFT HAND DOOR RIGHT HAND DOOR BARRIERFREE OPENINGS Adjust only if more tension is required to close and latch the door. Depending on opening conditions, a door adjusted to meet barrierfree forces may not have sufficient power to reliably close and latch the door. NONBARRIERFREE OPENINGSAdjust according to chart. The ITS 96 is UL listed for use on fire doors. Refer to door and frame manufacturer to determine if preperation is listed for fire door applications. FULL TURNS MAXIMUM FULL TURNS OF SPRING OF SPRING DOOR WT. ADJUSTER ADJUSTER (LBS) ITS961 ITS965 '6" 100 '0" '6" '0" DOOR WIDTH (INTERIOR) SPRING SIZE Place arm on closer according to hand of door. Attach arm with pinion screw. R.H. L.H. PINION SCREW 5mm Close valve by turning completely clockwise. Rotate arm 5 and attach closer to frame. R.H. 5 5 L.H. HINGE INSPK NO Rev.1/ INS NO PAGE 1 of Rev. 0/11
11 5 Thread screw a few turns into deadstop block. Insert components into track. Fasten track to door. 7 Open door to desired opening between 0 and 10. Tighten deadstop block. DEADSTOP BLOCK DEADSTOP ASSEMBLY The deadstop helps to prevent damage to the door and wall when the door is opened normally. The deadstop is not abuse resistant, and cannot replace a door stop in many situations. Deadstop is adjustable between 0 and 10 maximum. SLIDE SHOE Adjust sweep and latch valves. CAUTION: DO NOT REMOVE VALVES HOLD OPEN (OPTIONAL) NOTE: ARROWS ON HOLD OPEN AND SLIDE SHOE, MUST POINT AWAY FROM HINGE WHEN INSTALLING IN TRACK. () 6 () (INCREASE ONLY) Align hole in arm with slide shoe and attach with screw provided. 5mm SCREW 6mm HOLD OPEN UNITS ONLY INS NO PAGE of Rev. 0/11
12 9 (HOLD OPEN UNITS ONLY) Set hold open. A Place the hold open mechanism in desired position. Tighten screws #1 and # securely. M.5 C To enable hold open, push the white slide into the hold open mechanism. To disable hold open, pull the white slide away from hold open mechanism. 1 B To adjust hold open force, turn clockwise to increase force, and counter clockwise to weaken force. M.5 OFF ON INS NO PAGE of Rev. 0/11
Installation Type. Edge of Door. Pull (Hinge) Side Mounted. Hinge Edge of Door. Push (Stop) Side Mounted
Installation Instructions CAUTION An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility
More informationInstallation Instructions
Installation Instructions CAUTION An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility
More informationINSTRUCTIONS TS93 GSR PT RIGHT HAND ACTIVE LEFT HAND INACTIVE RIGHT HAND INACTIVE LEFT HAND ACTIVE
INSTRUCTIONS ATTENTION!!! Before you begin, determine installation type (RIGHT HAND ACTIVE OR INACTIVE). Door coordinator suitable for door from 59 to 98 in width. Inactive door width in the case of unequal
More informationTS93 STH. Surface applied door closer. Installation instructions: Pull side door mounted spring track Inverted closer with hold open (STH)
Surface applied door closer Installation instructions: Pull side door mounted spring track Inverted closer with hold open (STH) TABLE OF CONTENTS Closer overall Technical specifications Door template Size
More informationInstallation Instructions. Installation Type
Installation Instructions 800 & 8050 Slide Track Door Closers Non Hold Open & Hold Open Models Note: Hold open models are not permitted to be installed in Listed fire door assemblies. PULL SIDE MOUNTED
More informationInstallation Instructions. Installation Type
Installation Instructions 300 & 3050 Slide Track Door Closers Non Hold Open & Hold Open Models Note: Hold open models are not permitted to be installed in Listed fire door assemblies. PULL SIDE MOUNTED
More information316R Series Installation Instructions
316R Series Installation Instructions Multi size 1 thru 6 Non hold open closers CAUTION An incorrectly installed or improperly adjusted closer can cause property damage or personal injury. These instructions
More information351 DOOR CLOSER WITH DOUBLE LEVER ARM (OP) INSTALLATION INSTRUCTIONS
2 351 DOOR CLOSER WITH DOUBLE LEVER ARM (OP) INSTALLATION INSTRUCTIONS Strength Adjustable From Size 1 Thru 6 CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE Auxiliary door
More informationRegular Arm Installation. Closer mounts on hinge side of door (pull side) See Page 3. Closer cover not shown. Top Jamb Installation
UNIVERSAL HARDWARE CLOSER UH61 & UH62 STALLATION STRUCTIONS The Professional s Choice MULTI SIZE 1 THRU 6 NON HOLD OPEN CLOSER CAUTION! An incorrectly installed or improperly adjusted door closer can cause
More informationSARGENT 1331 DOOR CLOSER INSTALLATION INSTRUCTIONS WITH JUO (JO & JP9) ARMS
SARGENT 1331 DOOR CLOSER INSTALLATION INSTRUCTIONS WITH JUO (JO & JP9) ARMS Strength Adjustable From Size 1 Thru 6 CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE Auxiliary
More informationSARGENT 1331 DOOR CLOSER INSTALLATION INSTRUCTIONS WITH JUH (HOLD OPEN) ARMS
SARGENT 1331 DOOR CLOSER INSTALLATION INSTRUCTIONS WITH JUH (HOLD OPEN) ARMS Strength Adjustable From Size 1 Thru 6 CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE. FOR ASSISTANCE,
More informationINSTRUCTIONS FOR 1431 Door Closer with Hold Open Arms 1431 SERIES ADJUSTABLE FROM SIZE 1 THRU 6
INSTRUCTIONS FOR Door Closer with Hold Open Arms SERIES ADJUSTABLE FROM SIZE THRU 6 FOR INSTALLATION ASSISTANCE CALL SARGENT AT -800-77-77 / www.sargentlock.com Installation Instructions based on Application
More information5200 Series Door Closer Installation Instructions
5200 Series Door Closer I-C00187 R2 Regular Arm See Page 2 An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These installation instructions should
More information*18758* 2030 Series. 1 Installation. 2 Adjustment. 3 Hold Open Information BACKCHECK. * Hold open tracks. Installation Instructions
18758 18758 No maintenance required. 2035 EN 4 1 Installation 1a The hand of the door and the closer must be the same. RH or LH will be stamped on the mounting plate. See the proper template for your application.
More informationASSA ABLOY Series Installation Instructions. Regular Arm. Parallel Arm. Top Jamb Mount. Multi-Sized 1 thru 6 Non-Hold Open and Hold Open Models
9500 Series Installation Instructions Multi-Sized 1 thru 6 Non-Hold Open and Hold Open Models Regular Pages 5 & 6 Parallel Pages 7 & 8 Top Jamb Mount Pages 9 & 10 IMPORTANT: An improperly installed or
More informationThese door closers should NOT be installed on the exposed side (weather side) of exterior doors. WOOD 3/16" 1/4"- 20
Hollow-metal doors require channel or box-type reinforcement when thru-bolt mount is specified. Hold open arms are not permitted on fire doors. Sex-bolts may be required for wood or plastic faced fire
More informationPFD-22 Top OHC Patch Fitting & PFD-10 Bottom Patch Fitting Installation Instructions
Top OHC Patch Fitting & Bottom Patch Fitting Installation Instructions For Installation Assistance, Call 855.594.6989 www.assaabloyglass.us Tools Needed: Torque Wrench and Bit 5mm Allen Wrench 6 7 /16"
More informationNote: The dimensions of the Template are shown in inches. See attached page for the Metric Conversion Table for millimeters.
801 Avenida Acaso, Camarillo, Ca. 93012 (805) 494-0622 www.sdcsecurity.com E-mail: service@sdcsecurity.com These instructions are presented a in step by step sequence. Please read it through before installation.
More informationDC3210. Recommended Closer Size
Installation Instructions For Non-Hold Open or A Hold Open Arm Option DC3200 Series Multi-Sized thru 6 Regular Arm Universal Door Closers Parallel Arm Jamb Mount See pages 2&3 See pages 4&5 See pages 6&7
More informationSenior Swing. Caution
*740132* 740132 2800 Overhead Concealed Series 9500 Surface Applied Series Senior Swing Installation Instructions Caution LCN Senior Swing The Senior Swing Power Operator System is a low energy product
More informationASSA ABLOY. Model W91 Overhead Concealed Wood Frame Installation Instructions IMPORTANT: BEFORE INSTALLING: TO DETERMINE HAND OF YOUR DOOR:
Model W91 Overhead Concealed s Wood Frame Installation Instructions *Butt or 3/4 Offset Pivot Hung, Multi Sized 1-3, 3-6 Non-Hold Open and Hold Open Models *Other means except 4-1/2" x 4-1/2" or 3/4" offset
More informationD3976 RECESSED EXIT INSTALLATION INSTRUCTIONS
PACKAGE CONTENTS PRODUCT MUST BE INSTALLED ACCORDING TO ALL APPLICABLE BUILDING AND LIFE SAFETY CODES TEMPLATE INSTALLATION INSTRUCTIONS STRIKE HAND TOOL 5/32 HEX KEY ROD END CAPS EXIT DEVICE CRANK ARM
More informationDoor Closers. General Information
General Information Hager Companies offers a variety of surface door closers to meet a wide range of applications and uses. Heavy Duty, Grade 1 door closers are ideal for schools, hospitals, and other
More information1431 DOOR CLOSER WITH STANDARD DUTY ARMS (WITHOUT HOLD OPEN) INSTALLATION INSTRUCTIONS 1431 SERIES ADJUSTABLE FROM SIZE 1 THRU 6
1431 DOOR CLOSER WITH STANDARD DUTY ARMS (WITHOUT HOLD OPEN) INSTALLATION INSTRUCTIONS 1431 SERIES ADJUSTABLE FROM SIZE 1 THRU 6 FOR INSTALLATION ASSISTANCE, CALL SARGENT AT 1-800-727-5477 www.sargentlock.com
More informationTOOLS REQUIRED Metal Wood Wood and Metal Screws. #16 Drill #12-24 Tap. 1/8 Drill
DEVICES COVERED IN THIS DOCUMENT: 4700S Surface Vertical Rod Device 4700SF Fire Exit Surface Vertical Rod Device TOOLS REQUIRED Metal Wood Wood and Metal Screws Sex Bolts #7 Drill ¼ -20 Tap #16 Drill #12-24
More informationFRONT BUMPER KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6
FRONT BUMPER KIT P/N 2882301 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these
More information3 wide x 3 deep Video Wall Display Installation Guide
HoverTrack Series 3 wide x 3 deep Video Wall Display Installation Guide VWD-3X3-X462 This display kit mounts NEC X461UN and X462UNS LCD monitors in a 3 wide by 3 deep landscape configuration. The frame
More informationHow To Measure Your Finished Opening
3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips
More informationF l a t S c r e e n A R M S I n s t a l l a t i o n
ITEM NUMBERS (1) #TOACAORG16 (2) #TOACAORG20 (3) #TOACATRP24 (4) #TOACATRP30 (5) #TOACATRPDS (6) #TOACATRPSS TOOLS REQUIRED (1) 3/8 Wrench (not provided) (2) Phillips head screwdriver (not provided) (1)
More information800 SERIES. Heavy-Duty Commercial Grade 1 Surface Applied Closers. Standard Features. 3 hours fire rated. openings of the door.
800 SERIES Heavy-Duty Commercial Grade 1 Surface Applied Closers Standard Features n Performance Complies with ANSI A156.4, Grade 1, 2 million cycles, UL/ULC listed up to 3 hours fire rated n Chassis/Closer
More informationED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS
ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS Ver.2 1300 SERIES CONCEALED VERTICAL ROD DEVICE Top Strike Latch Screws Strike Screws Release Plunger Top Latch Plunger Screws
More informationTorqueMaster Replacement Spring
TorqueMaster Replacement Spring Installation Instructions NOTE: Use these installation instructions in conjunction with the TorqueMaster Repair / Replacement Spring Program literature. Copyright 999 Wayne-Dalton
More informations tops & holder s Absolute Door Control and Entire Opening Protection
check mate s tops & holder s Absolute Door Control and Entire Opening Protection Copyright 2001-2018, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
More informationPantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or oth
88 5076 691 Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occurring to the parts. We have taken great
More informationJenny Legs Assembly Instructions
Jenny Legs Assembly Instructions R EXTENDED PHILLIPS BIT MM ALLEN WRENCH 6MM HEX DRIVE /" 007 Steelcase Inc. Grand Rapids, MI 90 U.S.A. Printed in U.S.A. Page of 6 88000 Rev F Jenny Club Instructions:
More informationArts & Crafts Dining Buffet IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prev
88 580 69 Arts & Crafts Dining Buffet IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood
More informationSM-RAZOR-ART2-L / SM-RAZOR-ART2-XL
SM-RAZOR-ART2-L / SM-RAZOR-ART2-XL Strong Razor Series Articulating Mount for Large and Extra Large Displays INSTRUCTION MANUAL Installation Manual Warnings: Installation of this product should be done
More informationCheckmate Stops & Holders. Absolute Door Control and Entire Opening Protection
Checkmate Stops & Holders Absolute Door Control and Entire Opening Protection checkmate stops & holders TABLE OF CONTENTS General Information...3 How to Select Product...4 Options...5 Certifications...5
More information98/9927. Devices covered by these instructions: Surface Vertical Rod Exit Device
911375-00 Surface Vertical Rod Exit Device 98/9927 Installation Instructions Devices covered by these instructions: 98/9927 Surface Vertical Rod Exit Device 98/9927-F (Fire) Surface Vertical Rod Exit Device
More informationASSEMBLY AND ADJUSTMENT
EDGE MONITOR ARM EDGE Rev A 2/17 Model EDGE-SLV Model EDGE-BLK Model EDGE-WHT ASSEMBLY AND ADJUSTMENT EDGE MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and
More informationSmartView Mounting Frame 3 Wide x 3 Deep Video Wall Display Installation Guide
SmartView Mounting Frame 3 Wide x 3 Deep Video Wall Display Installation Guide WMK-034 This display kit mounts ViewSonic 46 Video Wall displays in a 3 wide by 3 deep landscape configuration. The frame
More informationHomestead Bar Cabinet IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent s
88 5527 991 Homestead Bar Cabinet IMPRTANT NTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts.
More informationSECURITY DOORS - 2', 3', 4'
INTRODUCTION: CAREFULLY READ THE CONTENTS OF THESE INSTRUCTIONS, AS THEY INDICATE THE CORRECT STEP BY STEP PROCEDURE TO ASSEMBLE THE PRODUCT. THE CARTON CONTENTS PAGE(S) WILL IDENTIFY THE ASSEMBLY PARTS.
More informationFM125 & FM126 Service Guide
FM125 & FM126 Service Guide FM125-0022 & FM125-0024 Repair Kit 1 2 3 4 #1-1 Pc. FM125-5012 Ball Carrier Installation Tool (FM125-0022 Only) #2-2 Pcs. P5-287-R0 O-Ring #3-2 Pcs. P5-067-R2 O-Ring #4-1 Pc.
More informationMounting Instructions For 3-Piece Namur Style Mounting Bracket To 2-Way 60 Series Valves
Mounting Instructions For 3-Piece Namur Style Mounting Bracket To 2-Way 60 Series Valves NOTE: These instructions apply only to 60 series ball valves with bodies containing external mounting nibs. External
More informationMighty Mo GX Series Cabinet Installation Guide. OR Rev /11
Mighty Mo GX Series Cabinet Installation Guide OR-71601787 Safety and Warning ATTENTION The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating
More informationDublin Stalls Installation Instructions
Dublin Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 9/13/17 Part Identification Round Track Bracket (4) (Not Painted) Round
More informationInstallation/Care/Use Manual Soft Sides Freeze Resistant Fountain
Installation/Care/Use Manual Soft Sides Freeze Resistant Fountain EDFP217FPC Installer To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION.
More informationINSTALLATION INSTRUCTIONS Z7800 SERIES MORTISE LOCK
801 Avenida Acaso, Camarillo, Ca. 93012 (805) 4940622 www.sdcsecurity.com Email: service@sdcsecurity.com A. Door Preparation: INSTALLATION INSTRUCTIONS Z7800 SERIES MORTISE LOCK 1. Measure desired height
More informationShetland Stalls Installation Instructions
Shetland Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 1/9/18 Before you start Kit can accommodate up to 12 wide stall front
More informationinstallation guide
JANUS INTERNATIONAL 1 866 562 2580 w w w. j a n u s i n t l. c o m 2000 2500 3000 installation guide RIGHT DRIVE END SHOWN LH OPPOSITE LEFT TENSION END SHOWN RH OPPOSITE PUSH-UP OPERATION 2000 2500 3000
More information33/35A Series. Devices covered by these instructions: Rim Exit Device. CD33/35A Rim Exit Device EL33/35A Rim Exit Device SS33/35A Rim Exit Device
911402-00 Rim Exit Device 33/35A Series Installation Instructions Devices covered by these instructions: 33/35A Rim Exit Device CD33/35A Rim Exit Device EL33/35A Rim Exit Device SS33/35A Rim Exit Device
More informationEDGE2 DUAL MONITOR ARM
EDGE2 DUAL MONITOR ARM EDGE2 Rev A 2/17 Model EDGE2-SLV Model EDGE2-BLK Model EDGE2-WHT ASSEMBLY AND ADJUSTMENT EDGE2 DUAL MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning
More informationINSTALLING YOUR NEW SPRING LIFT ARM KIT
INSTALLING YOUR NEW SPRING LIFT ARM KIT 1. Measure the distance that the roof is to be raised. [If your lift system is completely non-functional, you will need to calculate or estimate this distance as
More informationTABLE OF CONTENTS REQUIRED TOOLS
TABLE OF CONTENTS SECTION SECTION TITLE PAGE NO. 1 2 3 4 5 Assembling Mounting Structure Installing Bicycle Supports Mounting Rack to Wall Adding Sections Customizing Rack Configuration REQUIRED TOOLS
More informationINSTALLATION INSTRUCTIONS CRL JACKSON
INSTALLATION INSTRUCTIONS CRL JACKSON 3185 MID-PANEL CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com 11M0252 ORDER
More informationRH-412 STEEL DOORS INSTALLATION INSTRUCTIONS
RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.
More informationActive Push Bar. Safety glasses Measuring tape Level Pencil Power drill Drill bits: 5/32, 3/4 Center punch Phillips screw driver
EX88 Interlocking Rim Exit Device Preparation Guide and Installation Instructions Box Contents EX88 Interlocking Rim Exit Device Back Bar Filler Plate Active Push Bar Cylinder and Trim Interface Kit Mounting
More information400 Toll Free: (800) Phone: (718) Fax: (718) RIXSON Overhead Holders. Closer-Holder Packages
Checkmate and Stops General Information Overhead stops are used to protect door assemblies.they cut down the wear and tear of frequency, closing mechanisms, wind gusts, abuse and vandalism. By limiting
More informationInstallation Manual for Metal Toilet Partitions Standard Series
For Video instructions http://www.hadrian-inc.com/tech-data/installation/toilet-partitions.aspx P a g e 1 Table of Contents Page General Notes and Tools Required 3 STEP 1: Establish Floor Bracket Locations
More informationINSTALLATION INSTRUCTIONS RH 412 STEEL DOORS
By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side. Note: Having the hood open makes the job
More informationFor installation assistance, contact SARGENT at DOORS SHOWN HERE SWING IN FOR ILLUSTRATION PURPOSES ONLY.
SARGENT Installation Instructions for LP8600 x LR8600 & 12-LP8600 x 12-LR8600 Series Low Profile Panic and Fire Exit Devices on Double Egress & Double Doors or LS8600 & 12-LS8600 Low Profile Exit Device
More informationDOOR KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6. Verify accessory fitment at Polaris.com.
DOOR KIT P/N 2882528 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation
More informationHD installation guide
JANUS INTERNATIONAL 1 866 562 2580 www.janusintl.c o m 1950 1950HD installation guide RIGHT DRIVE END SHOWN LH OPPOSITE LEFT TENSION END SHOWN RH OPPOSITE PUSH-UP OPERATION 1950 1950HD SHOWN A rolling
More informationSentinel Series Cigar Humidor End Tables
Sentinel Series Cigar Humidor End Tables Assembly Instructions Models: Sentinel 500, 1000 and 1500 Style: Traditional SENTINEL ASSEMBLY INSTRUCTIONS Congratulations! You have purchased a superior cigar
More informationD. Middle Panel. C. Middle Panel. 1 pc. B. Side Panel 1 pc. I. Back Stretcher. 1 pc. J. Front Stretcher. 1 pc. S. Door 1 pc. T.
itchen Cart IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the parts. We have taken great care
More informationRhino Packing Gland Tool
Instruction Sheet P/N Rhino Packing Gland Tool 1. Description See Figure 1. The Rhino packing gland tool is used to remove the packing gland from Rhino bulk unloader pumps. The tool consists of two components,
More informationINSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110
INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110 The KWE dual swing arm wall mount is designed to provide a broad range of viewing for Small
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Fifth Wheel Adapter Titan 999T5 W4198 KIT CONTENTS: Item Qty. Part Description Service Part Number A 1 Fifth Wheel Adapter
More informationSCC Inc. VA Series. Technical Instructions. Document No. VA-7000 February 1, VA Valve Actuator Assemblies with VRG Butterfly Valves.
February 1, 2016 VA Valve Actuator Assemblies with VRG Butterfly Valves Description Features Application VA valve actuator assemblies include a Siemens SQM actuator reliably mounted to a VRG butterfly
More informationCREW REAR DOOR KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
CREW REAR DOOR KIT P/N 2883437 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these
More information1 Rolscreen Cartridge Removal:
Rolscreen Retractable Screen Cartridge Dis-Assembly and Assembly Service Instruction These instructions apply to: Rolscreen Retractable Screen 2/2017-Current Tools Required: Flat blade screwdriver Drill/driver
More informationPreference Collection and Treatment Console INSTALLATION GUIDE
Preference Collection 5580.69 and 5580.96 Treatment Console INSTALLATION GUIDE WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious
More informationPontiac Grand Am SC/T Installation Instruction Sheet Aftermarket Front Fascia
Aftermarket Front Fascia be used correctly to install the secondary fascia to the existing fascia. 1 Fascia Front 5 Bolt M6-1.0x60 5 Washer 1/4x9/16 2 Bolt/Washer Assembly 1 Nut/Washer Assembly 1. Six
More informationTITAN2-EDGE Public Access Computer Station Dual Track
TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the
More informationInstallation Instructions - Model V4JSD 1
Installation Instructions - Model V4JSD 1 Support Assemblies: Parts list: (Note see enclosed cut sheet for quantities and dimensional information) A vertical structural member (1 ½ x 1 ½ modular frame)
More informationMounting Accessories. Installation Guide. VIVOTEK SD83XXE Speed Dome
VIVOTEK SD83XXE Speed Dome Mounting Accessories AM-116/117 Pendant Pipe AM-118 Pendant Head AM-221 Gooseneck AM-231 Parapet Mount AM-519 Pendant Adaptor Installation Guide Corresponding part numbers: AM-116:
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000
INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 Specifications: Accomodates Akira and Orion 84" displays without interface bracket; accomodates other large flat panel displays with
More informationINSTALLATION INSTRUCTIONS CRL JACKSON
INSTALLATION INSTRUCTIONS CRL JACKSON 1285 CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com 11M0248 ORDER OF ASSEMBLY
More informationICU TRACKLESS SLIDING DOOR
Interior View 0 Installation Instructions Tools Required: Screwdrivers Small Straight (Flat Blade) - for Terminal Block wiring # Phillips (Crosspoint) - for various #8, #0, and #4 screws Wrenches / Sockets
More informationESA-300 Full Breakout
Interior View 0 Installation Instructions For use with ESA II Controler DORMA AUTOMATICS, Inc. 94 Sherwood Drive Toll-Free: 877-67-6 DL844-00 Lake Bluff, IL 60044 Fax: 877-4-7999 Rev. /07 Tools Required:
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationFOLDAWAY DOOR SECTION OPTION 6. Assembly Instructions. Folding Work Desk (adjustable shelves behind can be accessed when the desk is in use)
FOLDAWAY DOOR SECTION OPTION 6 Folding Work Desk (adjustable shelves behind can be accessed when the desk is in use) Assembly Instructions It is strongly recommended to have two persons present when assembling
More informationInstallation Manual for Metal Toilet Partitions Elite & Elite Plus Series
P a g e 1 Table of Contents Page General Notes and Tools Required 3 STEP 1: Establish Floor Bracket Locations 4 STEP 2: Fasten Floor Brackets 4 & 5 STEP 3: Erect Panels 6 STEP 4: Erect Wall Pilaster 7
More informationInstalling flat panels on the MPL15 wall mount
Installing flat panels on the MPL15 wall mount The MPL15 (DS-VW775) is a full-service video wall mount that can accommodate tiled LCD panels with up to a 400 x 400 mm VESA pattern in portrait and landscape
More informationPortableTM. Indoor Outdoor Clothesline. Owner s Manual. TO SUIT MODELS: PortableTM 170 PortableTM 120
PortableTM Indoor Outdoor Clothesline Owner s Manual TO SUIT MODELS: PortableTM 170 PortableTM 120 Introduction Congratulations Congratulations on the purchase of your Portable Clothesline, which will
More informationJ. Base 1 pc. 1 pc. P. Shelf 2 pcs. Gate Leg. 1 pc. Head Cap Bolt 13 pcs. (+1 extra) Cam Lock Screw. Cam Lock. 20 pcs. (+1 extra)
88 5023 95C Kitchen Island with Breakfast Bar IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the
More informationInstallation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens
Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens Model# IM760P, IM760P-S IM760PU, IM760PU-S Screen size range 32" to 71" (81 to 180 cm) 32" to 60" (81 to 152 cm) IM760P IM760P-S
More informationPreference Collection 5580 Treatment Console INSTALLATION GUIDE
Preference Collection 5580 Treatment Console INSTALLATION GUIDE 0 WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious injury
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationBF12-SERIES Flash Stands
BF12-SERIES Flash Stands Document # 16-462 Assembly and Operating Instructions Please review all these instructions prior to assembly. The BF12-SERIES stands come in two models, standard duty and heavy
More informationINSTALLATION INSTRUCTIONS CRL JACKSON
INSTALLATION INSTRUCTIONS CRL JACKSON 2085 CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com 11M0250 ORDER OF ASSEMBLY
More informationBarnside Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratch
88 5516 653 Barnside Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have
More informationInstallation Instructions 50 (06-09) 1-15/32 15/32 21/32. 1/4-20 x 5/8" FHMS or #14 x 1/2" FHWS 1/16 1/4. Floor Plate
RIXSON ASSA ABLOY 3/4 Template Jamb 1/8 2- R. Max. 1-7/16 1-1/32 2-2-3/4 7/8 Dia. C L 1-1/4 Dia. Installation Instructions 50 (06-09) Finish Plate 340 TOP PIVOT Pivot Shown Engaged 9/16 1/16 1/4 1-15/32
More informationInstallation Instructions for Converting Hinging on Roll-In Refrigerators
Installation Instructions for Converting Hinging on Roll-In Refrigerators Part number 161651 hinge conversion kit RH is for converting a right side hinged door and part number 161652 hinge conversion kit
More informationTopo Freestanding Applications - Private Office
4 3 2 Topo Freestanding Applications - Private Office Combo Wrench If you have a problem, question, or request, call your local dealer, or Coalesse at 1.800.627.6770 Or visit our website: www.coalesse.com
More informationINSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET
HIGH EDGE 2 1/4"(57mm) 03079400070 INSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET IMPORTANT: THIS LOCK IS NON-HANDED. LOCK IS FACTORY PACKED PREADJUSTED FOR 1³ ₄" (45mm)
More informationSentinel Series Cigar Humidor End Tables
Sentinel Series Cigar Humidor End Tables Assembly Instructions Models: Sentinel 500, 1000 and 1500 Style: Contemporary SENTINEL ASSEMBLY INSTRUCTIONS Congratulations! You have purchased a superior cigar
More informationTIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 TIRE RACK INSTALLATION INSTRUCTIONS 07-11 Dodge Sprinter Please read before beginning Stainless steel hardware may bind together
More informationINSTRUCTION SHEET U19
U19 All Refrigerator and All Freezer Trim Kit Installation Product Line: U19 All Refrigerator and All Freezer Models Parts Included in Kit TRIMKITEZ1 (Part# 297333500): Single Trim Kit Components Single
More information