1 Rolscreen Cartridge Removal:

Transcription

1 Rolscreen Retractable Screen Cartridge Dis-Assembly and Assembly Service Instruction These instructions apply to: Rolscreen Retractable Screen 2/2017-Current Tools Required: Flat blade screwdriver Drill/driver with #1 square drive bit Operating a retractable screen may result in a static discharge. A static discharge in the! CAUTION presence of a flammable substance such as aerosol lubricant could cause ignition. To avoid injury and/or property damage, do not use any flammable substance on a retractable screen. 1 Rolscreen Cartridge Removal: A. With the screen fully raised; Remove the screen guide attachment screws. Number of screws will vary depending on window height. 1A 1A B. Grasp the guide and pull it toward the center of the window and then down to remove. Repeat 1A-1B on other guide. 1B 1B 2016 Pella Corporation Page 1 of 8 Rev. 10/17/2016 Part Number: 81XJ0000

2 1 Rolscreen Cartridge Removal (Continued): C. Remove the Rolscreen cartridge attachment screw from each end cap. Be sure to hold the Rolscreen cartridge when removing screws so it does not fall out of window. 1C 1C D. Remove the Rolscreen cartridge and set on smooth flat work surface. 1D 1D 2 Rolscreen Cartridge Disassembly: A. Remove the head cover by pulling the bottom of the cover up and lift cover off the screen assembly. 2A 2A Page 2 of 8

3 2 Rolscreen Cartridge Disassembly (Continued): B. Push one end cap away from the screen roll, repeat on the other end and remove the screen roll. 2B 2B 2B C. Grasp one of the end caps and the back cover and disconnect the cover from the end cap. Repeat on the other end. 2C 2C 2C D. A disassembled cartridge is shown here, it includes: 1 head cover 1 screen roll 1 back cover 2 mounting brackets/end caps (1 LH & 1 RH) 2D Page 3 of 8

4 3 Rolscreen Cartridge Assembly: A. Align the tab on one end cap with the slot in one end of the back cover press into place. 3A 3A 3A Back cover snapped into end cap B. Repeat on the other side. 3B 3B 3B Back cover snapped into end cap C. With the screen cloth roll control bar on the bottom, align the end of the roll with the end cap hole and insert it into position. 3C 3C 3C Page 4 of 8

5 3 Rolscreen Cartridge Assembly (Continued): D. On the other end, align the end cap star gear with the matching end of the tube. 3D 3D 3D NOTE: In some cases it may be necessary to use a flat blade screwdriver to adjust the position of the star gear to align with the tube. E. Install the head cover onto the assembly being sure to align the end cap tab with the slots on the back side on the top of the cover. Rotate cover and snap the bottom into place. End Cap Tab End Cap tab in the head cover slot Page 5 of 8

6 3 Rolscreen Cartridge Assembly (Continued): F. Add tension to the retraction spring: Locate the slotted end of the screen assembly; to set the tensions - use a flat blade screwdriver to turn the spring assembly in the direction of the arrows. Depending on the width unit, the number of turns (full rotations) required to re-tension when the tension is released will vary: 3F Units with frame width of 20-3/4" or less require 11 turns for re-tensioning. Units with frame width > 20-3/4" require 27 turns for re-tensioning. After the final rotation, turn the screwdriver back slightly until resistance is felt indicating the spring tension will hold. If resistance is felt immediately do not force it back any further because the tensioning mechanism could be damaged by too much force. 4 Rolscreen Cartridge Installation: A. From the interior position the Rolscreen Assembly at the head of the window. 4A 4A B. While holding the assembly in position, install an attachment screw at a slight angle up (~25 ) in the hole of the end caps on each side of the assembly. 4B 4B Page 6 of 8

7 4 Rolscreen Cartridge Installation (Continued): C. Place the top of a Rolscreen guide against the frame with pull bar weatherstrip in the guide channel. (It may be necessary to reposition the pull bar to facilitate proper installation of the guide.) Position the bottom of the guide against the frame and on top of the sill. 4C 4C NOTE: It is critical the exterior side of each guide channel be positioned in the Rolscreen assembly end cap as shown and the bottom of the guide touches the sill stop and pressed firmly against the jamb stops. D. While pressing the guide to the frame with the bottom of the guide touching the sill stop; install the guide screws beginning with the bottom screw. The number of screws will vary depending on the height of the window. 4D 4D Page 7 of 8

8 4 Rolscreen Cartridge Installation (Continued): Operating a retractable screen may result in a static discharge. A static discharge in the! CAUTION presence of a flammable substance such as aerosol lubricant could cause ignition. To avoid injury and/or property damage, do not use any flammable substance on a retractable screen. Install the second guide, repeating steps 4C 4D. E. Test the closing operation of screen by pushing down firmly with both hands towards the ends of the screen bar and snapping the bar into place at the sill. 4E Page 8 of 8