Retractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors)

Size: px
Start display at page:

Download "Retractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors)"

Transcription

1 Retractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors) IMPORTANT: Please read before you begin.

2 Table of Contents and Tool/Material Requirements START PAGE Safety Alert Symbol iii Components Installation Diagrams Installation Packs Installation Preparation Assemble Components Fit Screen Assembly Into Opening Measuring Tape, Level, Quick Clamps Secure Screen Assembly Level, Power Drill with Drill Bits and Phillips Screwdriver Bits, Caulk Gun, Clear Silicone Caulk Install Sill Slide Bolt Keeper Power Drill with Drill Bits and Phillips Screwdriver Bits, Sill Slide Bolt Keeper (from Installation Pack) Install Head Slide Bolt Keeper Power Drill with Drill Bits and Phillips Screwdriver Bits, Sill Slide Bolt Keeper (from Installation Pack) Adjust Interior Screen Handles Soft Mallet or Padded Wood Block and Hammer Tension Adjustment Stiff Bladed Putty Knife, Soft Mallet or Padded Wood Block and Hammer Additional Adjustments Stiff Bladed Putty Knife, Soft Mallet or Padded Wood Block, Hammer, Power Saw, Aluminum Cutting Blade Installation Variation One-Wide Doors & Center Hinged Doors (Install Screen Keeper) Screen Keeper from Installation Pack, Drill W/Drill Bits and Phillips Screwdriver Installation Variation Center Hinged Door (Install L-Brackets) L-Brackets from Installation Pack, Tape Measure, 2mm Allen Socket Wrench Replaceable Parts ii

3 Recognize this symbol. This is the Safety-Alert symbol. When you see this symbol be alert to the potential for personal injury or product damage. Falling from window or door opening may result in serious injury or death. DO NOT leave openings unattended when children are present. Screen will not stop children, any one or anything from falling out window or door. Keep children and objects away from open windows or doors. Improper use of hand and power tools could result in personal injury and/or product damage. Follow equipment manufacturers instructions for safe operation. Always wear safety glasses. The manufacturer reserves the right, as necessary, to change product specifications, installation procedures, materials, prices and terms of purchase without notice. iii

4 Components FIGURE 1 VIEWED FROM THE EXTERIOR HEAD TRACK HEAD SHOOT BOLT KEEPER PULL PULL SILL TRACKS SILL SHOOT BOLT KEEPER PATIO DOORS SILL TRACK ENTRY DOORS The components in (FIGURE 1) are typical of the items that must be installed on a two-wide door. Not shown is the installation pack (see Page 4). The inset in (FIGURE 1) shows the two possible sill track configurations. Because the components are custom sized to fit, no cutting is required. The following instructions describe the complete installation procedure for a two-wide door. Where installation differs because of door type, you will be referred to the Installation Variation section which shows details for other door types. No matter what door type, installation consists of assembling the screen cassette(s) to the head track and sill track, slipping the assembly into the door frame, and screwing the assembly in place. Some hardware needs to be attached and is dependent upon door and screen type. Following the installation instructions is a parts list. 1

5 Components (cont.) Most components will fit only one way and are not handed. The screen cassette(s) can be installed on either side of the doorway but must be flipped endfor-end so the flat side is always towards the structure s interior (FIGURE 2). Consequently, the end cap with the tension adjustment spring can be either at the top or bottom of the screen cassette (FIGURE 2). Typical unit installation diagrams are shown on the following pages. FIGURE 2 VIEWED FROM EXTERIOR TOP LEFT CORNER VIEWED FROM EXTERIOR TOP RIGHT CORNER END CAP WITH SPRING, BUSHING, AND CAP END CAP WITH BRAKE FLAT SIDE OF FLAT SIDE OF INTERIOR INTERIOR END CAP WITH SPRING, BUSHING, AND CAP END CAP WITH BRAKE 2

6 Installation Diagrams FIGURE 1 Two-Wide, Side-Hinged, In-Swing Patio Door Side View Top View FIGURE 2 Two-Wide, Center-Hinged, In-Swing Patio Door Side View Top View FIGURE 3 One-Wide, Side-Hinged, In-Swing Patio Door Side View Top View 3

7 Installation Diagrams (cont.) FIGURE 4 One-Wide, In-Swing Entry Door Side View Top View A #8x½" PH PAN HEAD W/#6 HEAD TEK 410 SS #8x¾" PH PAN HEAD TYPE A 410 SS B C #8x1" PH PAN HEAD TYPE A 410 SS D MECHANICAL LATCH W/SHIMS AND SCREWS Installation Packs Installation packs are included with each retractable screen and contain the screws, latches, and keepers required for your specific installation. E SILL SLIDE BOLT KEEPER F HEAD SLIDE BOLT KEEPER HINGED PATIO ONE-WIDE SIDE HINGED G L-BRACKET Qty. Item Description Part Number 4 A #8 x 1/2" PH Pan Head W/#6 Head TEK 410 SS B #8 x 3/4" PH Pan Head Type A 410 SS D Mechanical Latch With 2 Shims And Screw Pack (Screw Pack Has four #6 x 3/4" SS FH Screws) White or All Other Colors HINGED PATIO TWO-WIDE SIDE HINGED Qty. Item Description Part Number 8 A #8 x 1/2" PH Pan Head W/#6 Head TEK 410 SS B #8 x 3/4" PH Pan Head Type A 410 SS F Head Slide Bolt Keeper And Screw Pack (Screw Pack Has four #4 x 5/16" SS FH Screws) or E Sill Slide Bolt Keeper

8 A #8x½" PH PAN HEAD W/#6 HEAD TEK 410 SS #8x¾" PH PAN HEAD TYPE A 410 SS B C #8x1" PH PAN HEAD TYPE A 410 SS D Installation Packs (cont.) MECHANICAL LATCH W/SHIMS AND SCREWS E SILL SLIDE BOLT KEEPER F HEAD SLIDE BOLT KEEPER G L-BRACKET CENTER HINGED PATIO [CODES A, B, ALL] [CODES E & F 3-WIDES] Qty. Item Description Part Number 4 A #8 x 1/2" PH Pan Head W/#6 Head TEK 410 SS B #8 x 3/4" PH Pan Head Type A 410 SS C #8 x 1" PH Pan Head Type A 410 SS Color Matched 1 D Mechanical Latch With Two Shims And Screw Pk (Screw Pack Has four #6 x 3/4" SS FH Screws) 2 G L-Bracket Color Matched thru White Or All Other Colors CENTER HINGED PATIO [CODES E & F] [FOUR-WIDES] Qty. Item Description Part Number 8 A #8 x 1/2" PH Pan Head W/#6 Head TEK 410 SS B #8 x 3/4" PH Pan Head Type A 410 SS C #8 x 1" PH Pan Head Type A 410 SS Color Matched thru F Head Slide Bolt Keeper And Screw Pack (Screw Pack Has four #4 x 5/16" SS FH Screws) or E Sill Slide Bolt Keeper G L-Bracket Color Matched CENTER HINGED PATIO [CODE G] [FOUR-WIDES] Qty. Item Description Part Number 6 A #8 x 1/2" PH Pan Head W/#6 Head TEK 410 SS B #8 x 3/4" PH Pan Head Type A 410 SS C #8 x 1" PH Pan Head Type A 410 SS Color Matched thru D Mechanical Latch With Two Shims And Screw Pk (Screw Pack Has four #6 x 3/4" SS FH Screws) 1 E Sill Slide Bolt Keeper G L-Bracket Color Matched White Or All Other Colors 5

9 A #8x½" PH PAN HEAD W/#6 HEAD TEK 410 SS #8x¾" PH PAN HEAD TYPE A 410 SS B C #8x1" PH PAN HEAD TYPE A 410 SS D Installation Packs (cont.) MECHANICAL LATCH W/SHIMS AND SCREWS E SILL SLIDE BOLT KEEPER F HEAD SLIDE BOLT KEEPER G L-BRACKET EDS ONE-WIDE Qty. Item Description Part Number 4 A #8 x 1/2" PH Pan Head W/#6 Head TEK 410 SS B #8 x 3/4" PH Pan Head Type A 410 SS D Mechanical Latch With 2 Shims And Screw Pack (Screw Pack Has four #6 x 3/4" SS FH Screws) EDS TWO-WIDE White or All Other Colors Qty. Item Description Part Number 6 A #8 x 1/2" PH Pan Head W/#6 Head TEK 410 SS B #8 x 3/4" PH Pan Head Type A 410 SS F Head Slide Bolt Keeper And Screw Pack (Screw Pack Has four #4 x 5/16" SS FH Screws) EDS P&L AND LPL Qty. Item Description Part Number 4 A #8 x 1/2" PH Pan Head W/#6 Head TEK 410 SS B #8 x 3/4" PH Pan Head Type A 410 SS D Mechanical Latch With 2 Shims And Screw Pack (Screw Pack Has four #6 x 3/4" SS FH Screws) 2 G L-Bracket Color Matched or White or All Other Colors EDS LPPL Qty. Item Description Part Number 6 A #8 x 1/2" PH Pan Head W/#6 Head TEK 410 SS B #8 x 3/4" PH Pan Head Type A 410 SS C #8 x 1" PH Pan Head Type A 410 SS Color Matched thru F Head Slide Bolt Keeper And Screw Pack (Screw Pack Has four #4 x 5/16" SS FH Screws) or G L-Bracket Color Matched The following instructions show installation on a two-wide, side hinged door unit. Basic installation and adjustment steps are similar for all door types. Significantly different installation requirements will be explained and illustrated. Unless stated otherwise for your door type, complete the following procedures.

10 Installation Preparation FIGURE 1 1. Clean all areas of existing door frame. Include the sill, head jamb, and side jambs. A clean flat FIGURE 2 surface is required for proper screen installation and operation (FIGURE 1). 2. Unpack all components and lay them out on a protected surface (FIGURE 2). These are the parts for a two-wide, side hinged door. Pictured from front to rear are: the sill track, screen cassette, screen cassette, and head track. FIGURE 3 3. One screen cassette on multi-wide units will have a slide bolt operator mounted (FIGURE 3). When installed, this cassette should be located so its screen will be in front of the inactive door panel. SLIDE BOLT OPERATOR 7

11 Assemble Components FIGURE 1 EXTERIOR For center hinged doors see Installation Variations Center Hinged Door on Page 20. L-Brackets must be attached to screen cassettes before head and sill tracks can be attached. L-Brackets are not used on side-hinged units. HEAD TRACK FIGURE 2 TAB TAB INTERIOR HEAD TRACK PULL IMPORTANT: For slide bolt units, be sure cassette with slide bolt operator is assembled to the head track so the operator will align with the inactive door panel when the screen is extended. NOTE: The head track for all retractable door screens is the same style. 1. Position head track and a screen cassette as shown in (FIGURE 1). The screen cassette s rounded side faces the exterior. The horizontal groove in the head track faces the exterior (FIGURE 4). 2. Insert tabs on screen cassette into channels on the head track (FIGURE 2). Both tabs rest on top of their channels (FIGURES 2 & 3). 3. Slide screen cassette fully into the head track. When cassette is completely inserted the joint between screen cassette and head track should look like (FIGURE 4). 4. Assemble second screen cassette to head track the same way. FIGURE 3 FIGURE 4 HEAD TRACK HORIZONTAL GROOVE EXTERIOR PULL 8

12 FIGURE 4 PULL BOTTOM FIGURE 5 UNDERSIDE OF SILL TRACK Assemble Components (cont.) INTERIOR IMPORTANT: For slide bolt units, be sure cassette with slide bolt operator is assembled to the sill track so the operator will align with the inactive door panel when the screen is extended. NOTE: Sill track may vary from what is pictured here. The sill track shipped with your screen unit is matched to your door. 1. Position sill track and a screen cassette as shown in (FIGURE 4). The screen cassette s pull bar faces the exterior. The longer sloped side of the sill faces the interior (FIGURE 4). 2. Insert tab on screen cassette into channel in the sill track (FIGURES 5 & 6). Some sill tracks look like (FIGURE 5A) and are assembled to the screen cassette the same way the head track is assembled. 3. When the cassette and sill track are fully assembled the joint should look like (FIGURE 7). 4. Assemble second screen cassette to the sill and head track the same way. 5A DOOR SIDE JAMB DOOR SILL FIGURE 6 FIGURE 7 SILL TRACK PULL SILL TRACK EXTERIOR 9

13 Fit Screen Assembly Into Opening FIGURE 1 Top View Two-Wide Side-Hinged Patio Door INTERIOR FIGURE 2 HEAD TRACK FIGURE 3 SILL TRACK PULL DOOR HEAD JAMB INTERIOR DOOR INSERT DOOR SILL DOOR INSERT EXTERIOR PULL Handle screen assembly with care so that components do not come apart or get damaged. 1. From the exterior, place the screen assembly into the door frame (FIGURE 1). 2. Slide each screen cassette sideways until it is in full contact with its respective side jamb. 3. Ensure head track is in full contact with door head jamb (FIGURE 2). 4. Use a level and check that screen cassettes are vertical and plumb. 5. With cassettes plumb and vertical and the head track fully against door head jamb the sill track location should be automatically established. 6. Gently clamp screen cassettes in the door frame opening to securely hold the assembly level and plumb. 7. Using the screen s pull bar, alternately pull each screen to the mid-point of the door opening to check for operation and alignment. 7a. For one-wide units, pull screen fully open to side jamb to test operation. 8. Make adjustments needed to ensure smooth screen extension and retraction. See Page 15 for screen tension adjustments. 9. Allow screens to fully retract into cassettes. INTERIOR 10

14 Secure Screen Assembly FIGURE 1 FIGURE 2 1. While screen assembly is held securely in place, measure 6" from side jamb and drill a 3/32" diameter pilot hole through the sill track down into the door threshold (FIGURE 1). 2. Drill a second 3/32" pilot hole at 20" out from the side jamb (FIGURE 2). 3. Repeat Steps 1 and 2 for the opposite side of the sill track. 4. Unclamp screen assembly and carefully lift entire assembly clear of the door opening. 5. Clear away all metal shavings from drilling the pilot holes. 6. Apply silicone sealant to each of the pilot holes drilled in Steps 1-3. Sealant provides a seal after the sill track is screwed in place. 7. Carefully replace screen assembly into the door opening. Recheck for plumb and level. Align pilot holes in sill track with pilot holes in door threshold. Do not over tighten screws. Sill track could be distorted causing difficult screen operation. 8. Screw sill track to threshold with #8 x 1" Phillips pan head type A stainless screws through each pilot hole (FIGURE 3). 9. Apply #8 x 1/2" Phillips pan head with #6 head TEK 410 stainless screws evenly across the width of the head track to secure head track to the door s head jamb (FIGURE 4). FIGURE 3 IMPORTANT: Ensure all screws are driven deep enough and straight so the screw heads will not interfere with screen extension and retraction. FIGURE 4 For center-hinged doors return to Page 21 and secure L-brackets to astragal after completing all steps on Page

15 Install Sill Slide Bolt Keeper FIGURE 1 For one-wide and center-hinged doors, turn to Page 19 and install the screen keeper on doorway side jamb. The following slide bolt instructions do not apply to one-wide and center-hinged doors. FIGURE 2 1. Pull enough screen from each cassette so the screen will meet in the middle of the door opening (FIGURE 1). Magnetic strips built into the screen frames will hold the two sections together. 2. Locate the sill slide bolt keeper and attachment screws in the installation pack (FIGURE 2). Place slide bolt keeper on sill as shown (FIGURE 2) and locate so notch in keeper lines up with the sill slide bolt. 3. Using the slide bolt keeper as a guide, drill two 3/32" diameter pilot holes into the sill track through the keeper (FIGURE 3). 4. Fasten sill slide bolt keeper to sill track with two #8 x 3/4" Phillips pan head type A 410 stainless steel screws (FIGURE 4). SILL SLIDE BOLT KEEPER SILL SLIDE BOLT NOTCH FIGURE 3 FIGURE 4 12

16 Install Head Slide Bolt Keeper FIGURE 1 1. Locate the head slide bolt keeper and attachment screws in the installation pack (FIGURE 1). 2. Place slide bolt keeper on head as shown (FIGURE 1). Operate the slide bolt to help locate the keeper on the screen frame. Notch in keeper straddles the head slide bolt (FIGURE 1). Drill only deep enough to make hole in head track. Do not drill into screen frame. 2. Using the slide bolt keeper as a guide, drill two 3/32" diameter pilot holes into the head track through the keeper (FIGURE 2). FIGURE 2 Do not over-tighten screws. Keeper could be damaged with too much force. 4. Fasten head slide bolt keeper with two #4 x 5/16" Phillips flat head stainless steel screws (FIGURE 3). NOTE: (FIGURE 3) Shows head slide bolt disengaged from keeper. FIGURE 3 13

17 Adjust Screen Interior Handles FIGURE 1 FIGURE 2 The interior handles come pre-mounted on the inside of the screen frame; however they may need to be adjusted up or down so they are not in the way of the door handles. To Adjust Handles 1. With screen sections fully extended, close door panels enough to see if screen handles and door handles clear each other. They interfere in (FIGURE 1). 2. Open interior door to get it out of the way. Then use a soft hammer or padded wood block to gently tap the screen handle up or down (your choice) until the screen handle is clear of the door handle (FIGURE 3). 3. Check the other screen section and adjust as needed. 4. For good looks and function adjust both screen handles to the same height (FIGURE 4). FIGURE 3 FIGURE 4 14

18 Tension Adjustment FIGURE 1 FIGURE 2 END CAP END CAP PUTTY KNIFE PULL LOCATOR PIN Screen tension can be adjusted. Proper screen tension provides easy operation for both extension and retraction. Screen tension was set at a nominal level at the factory but may need to be adjusted to meet your specific needs and conditions. To adjust screen tension it is necessary to remove the screen cassettes from the doorway. 1. Retract the screens so they are completely in their respective cassettes. 2. Remove the screws holding the head and sill track to the door frame. Keep the screws for reinstallation. 3. Carefully lift the screen assembly out of the door frame opening. 4. One at a time, slide the screen cassettes out of the head and sill tracks. Set head and sill tracks aside for reinstallation. The screen retraction system is under rotational spring tension. When the end cap is removed it will want to quickly unwind. Prevent injury or damage by firmly holding end cap as you start the removal process. Holding the end cap from unwinding will also ensure your starting point for adjusting spring tension. FIGURE 3 LOCATOR PIN SOCKETS PULL WIND TO INCREASE TENSION LOCATOR PIN IMPORTANT: Tension is adjusted using the end cap with the spring. See FIGURE 2 on Page 2. It may be located on the top or bottom of the screen cassette, depending on how the cassette is mounted in the doorway. 5. Use a stiff bladed putty knife to gently pry between the end cap and screen cassette (FIGURE 1). 6. Do not let the end cap unwind. Start lifting the end cap out of the screen cassette (FIGURE 2). Pull the end cap out only far enough for the locator pins to release from their sockets (FIGURE 3). Once the locator pins are clear of the screen cassette, the end cap will want to unwind due to spring tension. 7. When the locator pins are free of their sockets, wind the end cap as shown in (FIGURE 3) to increase tension. Two to four complete revolutions are usually enough to provide a noticeable tension increase. To decrease tension let the end cap unwind a few revolutions. Continued on next page. 15

19 Tension Adjustment (cont.) FIGURE 4 BUSHING KEY KEYWAY NYLON BUSHING TENSION SPRING FIGURE 5 LOCATOR PINS INTO SOCKETS END CAP ROLL END CAP PULL TAB FOR SILL TRACK If the end cap fully unwinds, proceed as follows. 1. Be sure locator pins are pulled clear of their sockets. 2. Wind end cap as shown in (FIGURE 3, Page 15). Apply 14 to 17 full revolutions of the end cap to achieve a normal effective operating tension. You may need more or less tension depending on screen size, desired operating speed, etc. 3. With end cap manually held to retain spring tension, align the bushing key (FIGURE 4), on the nylon bushing, with the narrow keyway. 4. With the key and narrow keyway aligned, slide the nylon bushing into the screen roll core. 5. Rotate end cap until the locator pins align with the locator pin sockets in the screen cassette (FIGURE 5). Be sure tab for the sill track aligns with the pull bar. 6. Then push end cap into the screen cassette until the end cap is fully seated in the screen cassette (FIGURE 6). 7. Adjust tension on other screen cassette as explained above. 8. Reassemble head and sill tracks to screen cassettes. 9. Reinstall screen assembly in the door opening. 10. Test screen operation. Make additional adjustments as needed. Follow the previous instructions until acceptable screen operation is achieved. FIGURE 6 16

20 Additional Adjustments FIGURE 1 FIGURE 2 FIGURE 3 TRIM BOTH EDGES If adjusting screen tension does not provide smooth extension and retraction, there may be parts binding in the head or sill tracks. With Screen Installed 1. Use your finger to carefully check for screw heads that may be interfering with screen motion. Reset screws as needed. 2. Check head and sill tracks for a physical obstruction caused by debris. Remove item. 3. Spray interior of cleaned sill and head track with silicone spray lubrication. If further adjustment is required, the unit will need to be uninstalled. Follow previous instructions. With Screen Unit Uninstalled 1. Sliding bar ends may be too wide for the head and sill track (FIGURE 1). To access sliding bar ends, pull out enough screen from the screen cassette to clear the end cap sill and head track tabs. Remove sliding bar ends (FIGURE 1). Manually trim using 180 grit sandpaper on a flat, firm sanding block. Trim both the head and bottom sliding bar ends if needed. 2. Reassemble sliding bar ends into the top and bottom of the pull bars. If the whole screen assembly seems too tall it can be trimmed shorter. To Trim Screen and Cassette 1. Prepare a flat, smooth work surface that will allow supporting the screen cassette level with saw table. 2. Remove unit from doorway. Follow previous instructions. 3. Remove screen cassettes from head and sill track. Follow previous instructions. 4. Remove bottom end cap from cassette to be trimmed. Follow previous instructions. Remember this unit is under rotational spring tension and must be removed carefully. 5. Pull the end cap and its attached components completely out of the screen core. 6. Remove the sliding bar end from the bottom of the pull bar (FIGURE 1, above). 7. Cassette end ready for trimming should look like (FIGURE 3). In this image the rolled screen is pushed into the cassette and away from the cut line. This cut will reduce cassette and pull bar length. The screen could be trimmed by sliding it out into the saw blade s path. 17

21 Additional Adjustments (cont.) FIGURE 4 FIGURE 5 CAP W/TENSION SPRING CAP W/BRAKE Trim Screen Cassette Cont. Follow all power saw safety practices. Use only a blade suitable for non-ferrous metal cutting. Wear safety glasses and hearing protection. 8. Carefully cut screen cassette to new length (FIGURE 4). 9. Clean cut surface to remove all burrs and metal shavings. Reassemble Cassette Components 1. Insert sliding bar ends into pull bars. 2. The end cap assembly, removed prior to trimming the screen cassette, looks like either item in (FIGURE 5). The brake end cap slips in following instructions in Steps 3 5 below. The tension spring unit must be wound up. See Pages 15 and 16 for setting proper operating tension and reinstalling this style end cap. 3. For the shorter cap, align keys on the end cap with the keyway in the screen core (FIGURE 6). 4. Once keys and keyway align, slide the cap assembly into the screen cassette until the end cap is close to the cassette (FIGURE 7). 5. Align locator pins with their sockets. Once pins align, push end cap fully into screen cassette. Follow the Tension Adjustment instructions on Pages 15 and 16 to reset tension on each screen and complete end cap reassembly before installing unit back into the doorway. FIGURE 6 FIGURE 7 KEYWAY LOCATOR PINS INTO SOCKETS PULL KEYS END CAP ASSEMBLY END CAP TAB FOR SILL TRACK 18

22 Installation Variation One-Wide & Center Hinged Doors FIGURE 1 Install Screen Keeper One-wide doors require installing a keeper on the door side jamb to hold the screen in its fully opened position. The screen pull bar is equipped with a full length groove that latches to the keeper (FIGURE 1), providing keeper mounting flexibility. 1. Locate screen keeper about half way up the height of the doorway side jamb and in line with the screen handle. 2. Position keeper against the door side jamb as shown in (FIGURE 2). Use the keeper holes as a drilling template and drill a 5/32" diameter pilot hole in each location. FIGURE 2 IMPORTANT: Do not over tighten screws. 3. Attach keeper to door frame using two #6 x 3/4" stainless steel flat head screws (FIGURE 3) that are included in the Installation Pack. Turn to Page 14 and complete instructions, as necessary, on Pages 14 through 18 to finish your installation. FIGURE 3 19

23 FIGURE 1 Installation Variation Center Hinged Door FIGURE 2 HANDLE PULL ASTRAGAL SCREW ASTRAGAL L-BRACKET Install L-Brackets The screen cassette is secured to the astragal by means of an L-Bracket that is screwed securely to the astragal (FIGURE 1). 1. The L-Brackets are located in the Installation Pack that came with your screen. The bracket quantity is based on door type and size. 2. The L-Bracket slips over the screen cassette (FIGURE 3) with the longer leg facing the astragal. 3. Each screen cassette should have at least two L-Brackets applied. Locate one bracket 14" to 16" from the head end cap and one the same distance from the sill end cap (FIGURE 4). Continued on next page. L-BRACKET FIGURE 3 FIGURE 4 20

24 Installation Variations Center Hinged Door (cont.) FIGURE 5 4. L-Brackets are held in position on the screen cassette by an allen head set screw. After locating L-Brackets 14" to 16" from the head and sill end caps, tighten the set screw just enough to hold the bracket in position. Use a 2mm allen wrench on the set screw (FIGURE 5). Return to Page 8 and continue with the assembly and installation instructions through Page 11. After completing all instructions on Page 11 continue with Step 5 below. 5. After sill and head tracks are screwed in, following instructions on Page 11, use the provided #8 x 1" color matched Phillips pan head 401 stainless screws to secure the L-Brackets to the astragal. Drill pilot holes with a 3/32" drill bit and then apply two screws to each L-Bracket. 8. Install screen keeper on doorway side jamb (see Page 19). 21

25 Replaceable Parts FIGURE 1 PARTS IDENTIFICATION Circled numbers match Item No. in chart on next page. VIEWED FROM THE EXTERIOR 1 HEAD TRACK 9 HEAD SLIDE BOLT KEEPER 3 8 PULL 5 HEAD SLIDE BOLT 4 4 HANDLE HANDLE 5 SILL SLIDE BOLT PULL 8 SILL TRACKS PATIO DOORS 2 SILL TRACK 9 SILL SLIDE BOLT KEEPER 3 ENTRY DOORS The next pages provide detail drawings for replaceable parts and a chart of part numbers. The chart is arranged numerically to follow callout numbering in (FIGURE 1) above. Before ordering parts, measure your existing screen cassette height, doorway height, and doorway width (side jamb to side jamb). Also note the sill track type (inset in FIGURE 1). Replacement parts are sized to fit your present unit so measuring accuracy is important. Instructions for part replacement are separate from these installation instructions. They will be sent with replacement parts orders. 22

26 Replaceable Parts (cont.) 2 SILL TRACKS PATIO DOORS Item No. Description Part No. Drwg. No. 1 Head Track White Head Track Green Head Track Tan Sill Track White Sill Track Green ENTRY DOORS 2 Sill Track Tan Sill Track Black Screen Cassette White Screen Cassette Green COMPONENT KIT END CAP WITH SPRING, BUSHING AND CAP END CAP WITH BRAKE AND CAP HANDLES SLIDING END CAPS 3 Screen Cassette Tan Component Kit White Component Kit Black Slide Bolt Kit White Slide Bolt Kit Black Magnet (+) N/A 6 Magnet (-) N/A 7 Mechanical Latch and Shims White Mechanical Latch and Shims Black Screen and Core Installation Pack White 9 Installation Pack Black 5 SLIDE BOLT KIT HEAD SLIDING END PULL 6 MAGNET On two-wide door, magnet on primary screen is +. Magnet on secondary screen (w/slide bolts) is -. SILL Illustrations for items 7, 8, and 9 are on the next page. 23

27 Replaceable Parts (cont.) 7 MECHANICAL LATCH 8 AND CORE SCREWS MECHANICAL LATCH SHIMS CORE 9 INSTALLATION PACK #8x¾" PH PAN HEAD TYPE A 410 SS #8x½" PH PAN HEAD W/#6 HEAD TEK 410 SS #8x1" PH PAN HEAD TYPE A 410 SS MECHANICAL LATCH W/SHIMS AND SCREWS SILL SLIDE BOLT KEEPER HEAD SLIDE BOLT KEEPER L-BRACKET 24

28 WS Part No Rev. 0 6/06 Printed in U.S.A Door Manufacturer

4-lite Patio Door. Installation Instructions

4-lite Patio Door. Installation Instructions 4-lite Patio Door Installation Instructions IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. Note: Only the 5-0 x 6-8

More information

INOVO 2-LITE SLIDING PATIO DOOR

INOVO 2-LITE SLIDING PATIO DOOR INOVO 2-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.

More information

Atrium Patio Door Field Service Manual

Atrium Patio Door Field Service Manual Atrium Patio Door Field Service Manual December 2005 Table of contents Service Agreement Pg 2 Release Agreement Pg 5 Inspection form Pg 6 Warranty Pg 8 Replacing swing panel Pg 12 Replacing sliding panel

More information

Sliding Glass Door Assembly and Installation Guide

Sliding Glass Door Assembly and Installation Guide Sliding Glass Door Assembly and Installation Guide Index Door System Components and Hardware The following components are needed to complete the installation of your Sliding Patio Door unit. Check all

More information

3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS

3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS 3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. TOOLS NEEDED: Tape Measure

More information

INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS

INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.

More information

LEGENDS RETRACTABLE DOOR SCREENS

LEGENDS RETRACTABLE DOOR SCREENS LEGENDS RETRACTABLE DOOR SCREENS MAGNETIC LATCHING DESIGN SYSTEM 42 I N S T A L L A T I O N I N S T R U C T I O N S 1 MOUNTING OPTIONS Recess : Mount the Screen Cassette using Recess Mounting Clips Recess

More information

Contemporary 3 Panel Classic 5 Panel French Panel

Contemporary 3 Panel Classic 5 Panel French Panel Contemporary 3 Panel Classic 5 Panel French Panel (X) Operating / Lock Panel Left (O) Fixed Panel Right Note : Glazing Beads For All Panel Face To The Exterior 2 Panel XO Left Is Shown Above Opposite =

More information

6400, 8400 and 9400 Series Sliding Patio Door

6400, 8400 and 9400 Series Sliding Patio Door Contemporary 3 Panel Classic 5 Panel French Panel 6400, 8400 and 9400 Series Sliding Patio Door (O) Fixed Panel Left (X) Operating / Mullion Panel Right (X) Operating / Lock Panel Left (O) Fixed Panel

More information

Frameless Inline Door With Return QCI5263

Frameless Inline Door With Return QCI5263 INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges

More information

Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement

Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement 1 Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement The following instructions are a supplement

More information

Block Frame Inovo Patio Door/Transom/Sidelite Field Mulling Instructions. simonton.com/installation. If mulling sidelites, skip to Step 5.

Block Frame Inovo Patio Door/Transom/Sidelite Field Mulling Instructions. simonton.com/installation. If mulling sidelites, skip to Step 5. Effective Date: 10/1/17 Tools Needed Kit Contents Safety Glasses Cordless Drill Phillips Screw Bit Two-step Drill Bit (3/8-1/8 ) Utility Knife Interior Mullion Exterior Mullion Cover Hardware Kit Clamps

More information

Quick Fit Installation Guide Retractable Screen - Double Door

Quick Fit Installation Guide Retractable Screen - Double Door Quick Fit Installation Guide Retractable Screen - Double Door 1 REMOVE KIT PARTS FROM SHIPPING TUBE 2 Slide bolts 2 Rail receiver Clips 15 Mounting screws 1 Housing end cap screw 2 Handles 1 Housing end

More information

4. Partially open the operating panel and tilt the top toward the interior of the door (Figure 4). Lift the panel off the sill and set it aside.

4. Partially open the operating panel and tilt the top toward the interior of the door (Figure 4). Lift the panel off the sill and set it aside. Effective Date: 10/1/2017 Tools Needed Kit Contents Hardware Kit Safety Glasses Cordless drill Phillips screw bit Two-step drill bit (3/8-1/8 ) utility knife Interior Mullion Exterior Mullion Cover clamps

More information

Phone # La Jolla Doors. Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels

Phone # La Jolla Doors. Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels Phone # 800-440-8785 www.lajolladoors.com La Jolla Doors Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels Thank you for choosing La Jolla Doors In this manual you will

More information

SLIDING TUB / SHOWER ENCLOSURE WITH STATIONARY 90º PANEL

SLIDING TUB / SHOWER ENCLOSURE WITH STATIONARY 90º PANEL SLIDING TUB / SHOWER ENCLOSURE WITH STATIONARY 0º PANEL This instruction sheet applies to the following units. C, C7, C7, C77, C, C7 This instruction sheet also applies to the following units. VTE / VSE

More information

UNIT No FRAMELESS PIVOT SHOWER DOOR

UNIT No FRAMELESS PIVOT SHOWER DOOR INSTALLATION INSTRUCTIONS UNIT No. 3600 FRAMELESS PIVOT SHOWER DOOR NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time QCI0020 Rev. 3 Page 1 of 8

More information

Installation Instructions For Vinyl Sliding Patio Door & French Sliding Patio Door 1-Wide, 2-Wide and 4-Wide

Installation Instructions For Vinyl Sliding Patio Door & French Sliding Patio Door 1-Wide, 2-Wide and 4-Wide Installation Instructions For Vinyl Sliding Patio Door & French Sliding Patio Door 1-Wide, 2-Wide and 4-Wide Includes Instructions For Door and Frame Reversal For 2-Wide Doors and Jamb Extension Option

More information

Frameless Fixed Panel Slider

Frameless Fixed Panel Slider INSTALLATION INSTRUCTIONS Frameless Fixed Panel Slider QCI-5279 SINGLE ROLLER WITH ANTI-JUMP DOUBLE ROLLERS QCI5279 Rev Page Certified 08/09/6 Tools: To install your New Shower Enclosure, you may need

More information

Shetland Stalls Installation Instructions

Shetland Stalls Installation Instructions Shetland Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 1/9/18 Before you start Kit can accommodate up to 12 wide stall front

More information

Frameless Inline Door QCI5254

Frameless Inline Door QCI5254 INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5254 FRAMELESS DOOR / PANEL QCI5254 REV. 0 Page 1 Cer fied 06/16/2016 Parts List with wall mount hinges *Quanes may vary QCI5254 REV. 0 Page 2 Cer fied

More information

Vinyl Sliding Glass Door Assembly Instructions

Vinyl Sliding Glass Door Assembly Instructions Vinyl Sliding Glass Door Assembly Instructions SERIES SGD 5470/5570 Para instrucciones en español, visite: http://bit.ly/pgtassemblyinstructions Parts List ITEM 4 5 6 7 8 9 0 4 5 6 7 8 SGD 5470/5570 PARTS

More information

Mira Premium Series Bi-Parting French Sliding Patio Door Installation Instructions

Mira Premium Series Bi-Parting French Sliding Patio Door Installation Instructions PREMIUM SERIES W I N D O W S Mira Premium Series Bi-Parting French Sliding Recommended Tools & Accessories Tape Measure Level (3 or longer) Hammer Power Screwdriver Load bearing Shims Flashing (recommended)

More information

I n s t a l l a t i o n I n s t r u c t i o n s S E N T I N E L S E R I E S 1 50 SLIDING GLASS DOORS

I n s t a l l a t i o n I n s t r u c t i o n s S E N T I N E L S E R I E S 1 50 SLIDING GLASS DOORS I n s t a l l a t i o n I n s t r u c t i o n s S E N T I N E L S E R I E S 1 50 SLIDING GLASS DOORS Page 2-9: Installation Instructions, Figures 1, 2, & 3 Page 10-12: Figures A-1, A-2, & A-3: Installation

More information

HR175 Sash Replacement Kit Installation Instructions

HR175 Sash Replacement Kit Installation Instructions HR175 Sash Replacement Kit Installation Instructions IMPORTANT: Please read before you begin. Weather Shield HR175 Sash Replacement Kits Important: Thoroughly read and follow these instructions, failure

More information

TRUE TECHNICAL SERVICE MANUAL - ALL MODELS. DOORS/DRAWERS/LIDS

TRUE TECHNICAL SERVICE MANUAL - ALL MODELS.  DOORS/DRAWERS/LIDS DOORS/DRAWERS/LIDS 55 56 NOTES DOORS/DRAWERS/LIDS Swing s 73 74 NOTES INSTALLATION OF A GDM-SWING DOOR Phillips Head Screwdriver (2) - 1/8" Drift Punches (forged) Top Bracket NOTE: It may be necessary

More information

FOLDING DOOR - FOR FACTORY ASSEMBLED JAMBS WITH APPLIED SILL

FOLDING DOOR - FOR FACTORY ASSEMBLED JAMBS WITH APPLIED SILL FOLDING DOOR - FOR FACTORY ASSEMBLED JAMBS WITH APPLIED SILL READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according to

More information

InStallatIon InStruCtIonS for vinyl 2-lIte PatIo door assembled

InStallatIon InStruCtIonS for vinyl 2-lIte PatIo door assembled InStallatIon InStruCtIonS for vinyl -lite PatIo door assembled tools & materials you Will need: Measuring Tape Pencil Shims Square Hammer or Mallet Level Drill & Drill bits: 6", 8", 5 6", 7 6" Utility

More information

VYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4

VYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4 VYTEX PREMIUM SLIDING GLASS DOOR Table of Contents Precautions and Safety 2 Tools Required...3 Inspect and Prepare Door...4 Hardware and Parts Check List....4 Master Frame Assembly 5 Master Frame Installation..7

More information

FRAMELESS DOOR / PANEL WITH WALL MOUNT HINGES QCI5274

FRAMELESS DOOR / PANEL WITH WALL MOUNT HINGES QCI5274 FRAMELESS DOOR / PANEL WITH WALL MOUNT HINGES QCI5274 QCI0274 QCI5274 REV. Rev. 1 0 Page Page 1 1 Date Certified: Certified 06/16/2016 10/01/10 Parts List with wall mount hinges ITEM NO. Part # DESCRIPTION

More information

Assembly Instructions

Assembly Instructions Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt

More information

1200 SERIES 2 PANEL DOOR rev.1 DETAILED INSTALLATION INTRUCTIONS

1200 SERIES 2 PANEL DOOR rev.1 DETAILED INSTALLATION INTRUCTIONS 1200 SERIES 2 PANEL DOOR 10.2013 rev.1 DETAILED INSTALLATION INTRUCTIONS GENERAL: Door elevations shown in these instructions are as viewed from the outside. X denotes the active or moving panel(s). O

More information

Fold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE

Fold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE Fold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE This instruction guide provides the minimum recommended procedures to correctly prepare the rough opening, install a fold-a-way patio door unit and apply

More information

Chapter 9. Windows and Exterior Doors

Chapter 9. Windows and Exterior Doors Chapter 9. Windows and Exterior Doors 9.1 INSTALLING WINDOWS 9.2 INSTALLING EXTERIOR HOUSE DOORS 9.3 INSTALLING SHED DOOR 9.4 INSTALLING EGRESS COMPONENTS Tools needed by volunteers: Hammer Nail apron

More information

Laminate Cabinet Installation Instructions

Laminate Cabinet Installation Instructions Laminate Cabinet Installation Instructions www.easygaragestorage.com/installation How To Use These Instructions Thank you for your purchase! Please read each step of this manual thoroughly to ensure proper

More information

Please read and understand all instructions before beginning. These instructions cover impact and non-impact aluminum French Door 650/750.

Please read and understand all instructions before beginning. These instructions cover impact and non-impact aluminum French Door 650/750. The performance and proper operation of a door is only as good as the installation. By following these instructions, the probability of a good installation greatly increases. Please read and understand

More information

3/16 OR 1/4 FRAMELESS SWING DOOR WITH SINGLE INLINE PANEL OR TWO INLINE PANELS

3/16 OR 1/4 FRAMELESS SWING DOOR WITH SINGLE INLINE PANEL OR TWO INLINE PANELS / OR / FRAMELESS SWING DOOR WITH SINGLE INLINE OR TWO INLINE S This instruction sheet applies to the following units with a magnetic handle. C7, C7, C79 This instruction sheet also applies to the following

More information

Quick Fit Installation Guide Retractable Screen - Single Door

Quick Fit Installation Guide Retractable Screen - Single Door Quick Fit Installation Guide Retractable Screen - Single Door 1 REMOVE KIT PARTS FROM SHIPPING TUBE 15 Mounting screws 1 Housing end cap screw 2 Handles 1 Housing end cap 1 Bushing 1 Pull bar end cap 2

More information

Chapter 9. Windows and Exterior Doors

Chapter 9. Windows and Exterior Doors Chapter 9. Windows and Exterior Doors 9.1 INSTALLING WINDOWS 9.2 INSTALLING EXTERIOR HOUSE DOORS 9.3 INSTALLING SHED DOOR 9.4 INSTALLING BASEMENT EGRESS COMPONENTS Tools needed by volunteers: Hammer Nail

More information

Aluminum Clad Wood Window Field Mulling and Stacking Instructions

Aluminum Clad Wood Window Field Mulling and Stacking Instructions Aluminum Clad Wood Window Field Mulling and Stacking Instructions Mulling Stacking Mulling and Stacking IMPORTANT: Please read before you begin. TABLE OF CONTENTS AND TOOL / MATERIAL REQUIREMENTS START

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS TOOLS REQUIRED Rechargeable, variable speed drill 3/8 diameter drill bit 3 Robertson bits #0, #1 and #2 Slot screwdriver Non marring hammer with 1 head Level Caulk or sealant

More information

LEGENDS RETRACTABLE DOOR SCREENS

LEGENDS RETRACTABLE DOOR SCREENS I N S T A L L A T I O N I N S T R U C T I O N S 1 MOUNTING OPTIONS Recess : Mount the Screen Cassette using Recess Mounting Clips Recess within the door jamb area. Recess installations are the most typically

More information

Double Frameless Swing Door QCI5247

Double Frameless Swing Door QCI5247 INSTALLATION INSTRUCTIONS Double Frameless Swing Door QCI5247 WALL MOUNT HINGES QCI5247 REV. 0 Page 1 Certified 06/16/2016 Parts List with wall mount hinges *Quantities may vary **Quantities double where

More information

INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233

INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233 INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233 QCI5233 Rev 0 Page 1 Certified 06/20/2016 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay

More information

INSTALLATION INSTRUCTIONS. UNIT No. 160/760 THIN-LINE SHOWER ENCLOSURE

INSTALLATION INSTRUCTIONS. UNIT No. 160/760 THIN-LINE SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS UNIT No. 160/760 THIN-LINE SHOWER ENCLOSURE QCI0011 Rev. 0 Page 1of 10 Certified 10/18/2006 MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure;

More information

Steel Reinforced Joining Guide (Horizontal / Vertical)

Steel Reinforced Joining Guide (Horizontal / Vertical) (Horizontal / Vertical) for Andersen Patio Door and/or Elliptical Top Window Combinations Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation

More information

Knock Down Patio Door Assembly Instructions Regular & Impact

Knock Down Patio Door Assembly Instructions Regular & Impact Knock Down Patio Door Assembly Instructions Regular & Impact 72 x 80 72 x 82 72 x 96 96 x 80 96 x 82 96 x 96 Impress the Weather KD Patio Door Regular & Impact Sizes 72 x 80 72 x 82 72 x 96 96 x 80 96

More information

STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS

STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS 1290363 Revision 1 12/16 Page 1 Weather Shield Mfg., Inc. NOTICE CAUTION! Failure to install and maintain our product according to these instructions

More information

1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A

1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A 1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com

More information

Frameless Inline Door QCI5248

Frameless Inline Door QCI5248 INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5248 FRAMELESS PANEL / DOOR / PANEL QCI5248 REV. 0 Page 1 Certified 06/16/2016 Parts List with glass to glass hinges *Quantities may vary. **Support Bar

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Thank You, for your recent purchase with TrimLine Windows, Inc. This is a quality product and deserves a quality installation. Please follow the attached instructions for a quick

More information

Non-Reinforced Joining Guide (2-Way Horizontal and Vertical Joining) for Andersen 200 Series Tilt-Wash Double-Hung and Transom Windows

Non-Reinforced Joining Guide (2-Way Horizontal and Vertical Joining) for Andersen 200 Series Tilt-Wash Double-Hung and Transom Windows (2-Way Horizontal and Vertical Joining) for Andersen 200 Series Tilt-Wash Double-Hung and Transom Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly,

More information

SLIDING GLASS DOOR ASSEMBLY INSTRUCTION Series 680/780

SLIDING GLASS DOOR ASSEMBLY INSTRUCTION Series 680/780 10/07 M0200030 GENERAL NOTICE READING THESE INSTRUCTIONS FIRST AND FOLLOWING THE PROCEDURES IN PROPER SEQUENCE WILL REDUCE FRUSTRATION, COSTLY MISTAKES AND WASTED TIME. Protect main frame only with light

More information

Frameless Fixed Panel Slider QCI5279

Frameless Fixed Panel Slider QCI5279 Frameless Fixed Panel Slider QCI5279 F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com Frameless Fixed Panel

More information

A-935 RODA WALL MOUNT HINGES

A-935 RODA WALL MOUNT HINGES INSTALLATION INSTRUCTIONS A-935 RODA WALL MOUNT HINGES NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time FRAMELESS DOOR / PANEL CELESTA QCI0274 REV.

More information

Installation Guide. for E-Series/Eagle Clad Hinged Inswing French Door

Installation Guide. for E-Series/Eagle Clad Hinged Inswing French Door Installation Guide for E-Series/Eagle Clad Hinged Inswing French Door Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection in place.

More information

Series----SP3600A SHOWER DOOR

Series----SP3600A SHOWER DOOR Series----SP3600A SHOWER DOOR INSTALLATION INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. The Exploded Diagram

More information

ULTRA WINDOW & DOOR EXPANDERS AND RECEIVERS INSTALLATION INSTRUCTIONS

ULTRA WINDOW & DOOR EXPANDERS AND RECEIVERS INSTALLATION INSTRUCTIONS ULTRA WINDOW & DOOR S AND RECEIVERS INSTALLATION INSTRUCTIONS! CAUTION: *REMEMBER SAFETY FIRST* Proper Eye and! Hearing Protection must always be worn during installation of all window and door products.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS BUILDERS CHOICE FRAMED Shower Height Swing Door Model: L533 Rev. 09.03.13 MAINTENANCE: Two primary materials are used to manufacture your new Aquatic enclosure; tempered glass

More information

Vinyl Hinged Door Installation Instructions Structure With Weather Resistant Barrier Applied Before Door Installation

Vinyl Hinged Door Installation Instructions Structure With Weather Resistant Barrier Applied Before Door Installation Vinyl Hinged Door Installation Instructions Structure With Weather Resistant Barrier Applied Before Door Installation IMPORTANT: Please read before you begin. Part No. 1221586 Install 262 02/08 Printed

More information

Frameless Heavy Glass Door with Wall Mount Hinges

Frameless Heavy Glass Door with Wall Mount Hinges INSTALLATION INSTRUCTIONS Frameless Heavy Glass Door with Wall Mount Hinges QCI-5245 QCI5245 REV. 0 Page 1 Certified 06/16/16 Frameless Door with Wall Mount Hinges ITEM NUMBER DESCRIPTION QUANTITY 1 DOOR

More information

ATLANTIS RAIL Contact Information

ATLANTIS RAIL Contact Information ATLANTIS RAIL Contact Information Customer Service (800) 541-6829 (508) 732-9191 Spectrum System Installation Instructions Atlantis Rail s Spectrum System is an easy to install, universal cable railing

More information

InstallatIon InstructIons for 2-lIte PatIo Door unassembled

InstallatIon InstructIons for 2-lIte PatIo Door unassembled InstallatIon InstructIons for -lite PatIo Door unassembled tools & materials You will need: Measuring Tape Pencil Shims Drill & Drill bits: 6", 8", 5 6", 7 6" Utility Knife High-Performance Premium Silicone

More information

QCI0029 REV. 1 Page 1 of 11 Certified 07/06/05

QCI0029 REV. 1 Page 1 of 11 Certified 07/06/05 QCI0029 REV. 1 Page 1 of 11 Certified 07/06/05 MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure: tempered glass and anodized aluminum. To assure a long lasting finish

More information

SYSTEM 42 SCREEN CASSETTE WITH 30mm SIDE RAIL

SYSTEM 42 SCREEN CASSETTE WITH 30mm SIDE RAIL LEGENDS VERTICAL WINDOW RETRACTABLE SCREEN SYSTEM 42 SCREEN CASSETTE WITH 30mm SIDE RAIL I N S T A L L A T I O N I N S T R U C T I O N NOTE: Screen components must be installed on a flat surface to ensure

More information

Frameless Inline Door QCI5250

Frameless Inline Door QCI5250 INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5250 FRAMELESS PANEL / DOOR / PANEL QCI0249 REV. 3 Page 1 Certified 10/12/12 Parts List with pivot hinges *Quantities may vary. QCI0249 REV. 3 Page 2

More information

TorqueMaster Replacement Spring

TorqueMaster Replacement Spring TorqueMaster Replacement Spring Installation Instructions NOTE: Use these installation instructions in conjunction with the TorqueMaster Repair / Replacement Spring Program literature. Copyright 999 Wayne-Dalton

More information

FIXED PANEL SLIDER QCI5241

FIXED PANEL SLIDER QCI5241 INSTALLATION INSTRUCTIONS FIXED PANEL SLIDER QCI5241 FRAMELESS PANEL / DOOR / PANEL FRAMELESS DOOR / PANEL QCI5241 REV. 0 Page 1 Certified 06/16/2016 Parts List *Quantities may vary QCI5241 REV. 0 Page

More information

Oxford Stalls Installation Instructions

Oxford Stalls Installation Instructions Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or

More information

Transom Joining. for Andersen Elliptical Windows over Perma-Shield Gliding Patio Door

Transom Joining. for Andersen Elliptical Windows over Perma-Shield Gliding Patio Door Transom Joining for Andersen Elliptical Windows over Perma-Shield Gliding Patio Door INSTALLER: Please leave this guide with the building owner to file for future reference. Congratulations! You have just

More information

FIXED SHOWER SCREEN For Wall Mount Hinges QCI5283

FIXED SHOWER SCREEN For Wall Mount Hinges QCI5283 FIXED SHOWER SCREEN For Wall Mount Hinges QCI5283 QCI5283 Page 1 Date Certified: 06/16/2016 Parts List with wall mount clamp ITEM NO. DESCRIPTION QTY. 1 FIXED GLASS PANEL 1 2 WALL MOUNT CLAMP 1 3 U-CHANNEL

More information

FIG. #1 - ASD-90 & USD-90 Shower Door Assembly

FIG. #1 - ASD-90 & USD-90 Shower Door Assembly Installation Instructions for the Accent/Euro Collection FIG. #1 - ASD-90 & USD-90 Shower Door Assembly #1021 #1021 1 23 25 2 #1020 6 5 12 #1020 9 24 9 8 Hinge Assembly 2109, 2201, 2212, 2213, 2220 7 Please

More information

INSTALLATION GUIDE WOOD PIVOTING CIRCLE/ OVAL

INSTALLATION GUIDE WOOD PIVOTING CIRCLE/ OVAL WOOD PIVOTING CIRCLE/ OVAL READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according to these instructions will VOID any

More information

Frameless Door QCI5284

Frameless Door QCI5284 Frameless Door QCI5284 F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com INSTALLATION INSTRUCTIONS Frameless

More information

T he Double-Hung Replacement System replaces the sash and balance system of an older double-hung window. The

T he Double-Hung Replacement System replaces the sash and balance system of an older double-hung window. The Double-Hung Replacement System Installation The Pozzi Collection PID001 (12/03) T he Double-Hung Replacement System replaces the sash and balance system of an older double-hung window. The frame of the

More information

Tilt and Slider Replacement Window Installation Instructions

Tilt and Slider Replacement Window Installation Instructions Tilt and Slider Replacement Window Installation Instructions Installer Please leave this booklet for the homeowner after the install is completed. IMPORTANT: Please read completely before you begin. Part

More information

ELEGANCE SHOWER DOOR/ENCLOSURE INSTALLATION INSTRUCTIONS. Style A Style B Style C Style D

ELEGANCE SHOWER DOOR/ENCLOSURE INSTALLATION INSTRUCTIONS. Style A Style B Style C Style D ELEGANCE SHOWER DOOR/ENCLOSURE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical

More information

*D-1030* 1 PARTS CHECK 8 REVERSING INSTRUCTIONS F-XX-C & XX-C D Customer Service. Installation Instructions. Exit Devices

*D-1030* 1 PARTS CHECK 8 REVERSING INSTRUCTIONS F-XX-C & XX-C D Customer Service. Installation Instructions. Exit Devices *D-1030* D-1030 F-XX-C & XX-C Exit Devices Installation Instructions 8 REVERSING INSTRUCTIONS TO REVERSE THE HANDING OF A (F)XX-C DEVICE NOTE: TO REVERSE TRIM, REFER TO SEPARATE INSTALLATION SHEETS. 1

More information

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

InSTallaTIon InSTruCTIonS For 4-lITe PaTIo Door unassembled

InSTallaTIon InSTruCTIonS For 4-lITe PaTIo Door unassembled InSTallaTIon InSTruCTIonS For 4-lITe PaTIo Door unassembled Measuring Tape Pencil Shims Drill & Drill bits: 6", 8", 5 6", 7 6" Tools & materials You Will need: Square Hammer or Mallet Level Stiff Putty

More information

INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS

INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS 2008 Pella Corporation Part Number: 803V0101 INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS Installation Instructions for Typical Wood Frame Construction. These instructions were developed

More information

for Andersen 400 Series Woodwright Transom over 400 Series Woodwright Double-Hung or 400 Series Woodwright Picture Window

for Andersen 400 Series Woodwright Transom over 400 Series Woodwright Double-Hung or 400 Series Woodwright Picture Window for Andersen 400 Series Woodwright Transom over 400 Series Woodwright Double-Hung or 400 Series Woodwright Picture Window Congratulations! You have just purchased one of the many fine Andersen products.

More information

Closet System Installation Manual

Closet System Installation Manual Closet System Manual Thank you For choosing our Custom Closet Collection to fit all your needs Closets come fully assembled to make your project an enjoyable and satisfying experience. With quality Custom

More information

Assembly Instructions 10 X 10 Aluminum Frame Building

Assembly Instructions 10 X 10 Aluminum Frame Building Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal

More information

Model 750 Illustrated Installation Instructions Contractors Wardrobe

Model 750 Illustrated Installation Instructions Contractors Wardrobe Model 750 Illustrated Installation Instructions Contractors Wardrobe DESIGNERS MANUFACTURERS 26121 Avenue Hall Valencia, CA 9155 (661) 257-77 Fax: (661) 257-4907 Toll Free: (800) CW-DOORS (800) 29-6677

More information

INSTALLATION INSTRUCTIONS. Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING

INSTALLATION INSTRUCTIONS. Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING JANUARY, 2014 1 INSTALLATION Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING INSTRUCTIONS 2 FRAME ASSEMBLY JANUARY, 2014 601442 SHEAR BLOCK BALL BEARING NRP BUTT (FACTORY APPLIED

More information

SOKIII AND SOKIII XL

SOKIII AND SOKIII XL RV INSTALLATION MANUAL SOKIII AND SOKIII XL SLIDEOUT COVER Read this manual before servicing this product. Failure to follow the instructions and safety precautions in this manual can result in personal

More information

Safety glasses Measuring tape Level Pencil Power drill Center punch Phillips screw driver Saw horse

Safety glasses Measuring tape Level Pencil Power drill Center punch Phillips screw driver Saw horse EX76 Concealed Vertical Rod Exit Device Preparation Guide and Installation Instructions Box Contents EX76 Concealed Vertical Rod Exit Device Back Bar Active Push Bar Filler Plate Door Kit with Templates

More information

Topo Freestanding Applications - Private Office

Topo Freestanding Applications - Private Office 4 3 2 Topo Freestanding Applications - Private Office Combo Wrench If you have a problem, question, or request, call your local dealer, or Coalesse at 1.800.627.6770 Or visit our website: www.coalesse.com

More information

Model 6100 Illustrated Installation Instructions Contractors Wardrobe

Model 6100 Illustrated Installation Instructions Contractors Wardrobe Model 6100 Illustrated Installation Instructions Contractors Wardrobe DESIGNERS MANUFACTURERS 26121 Avenue Hall Valencia, CA 91355 (661) 257-17 Fax: (661) 257-4907 Toll Free: (800) CW-DOORS (800) 293-6677

More information

738 SERIES PIVOT SHOWER DOOR

738 SERIES PIVOT SHOWER DOOR INSTALLATION INSTRUCTIONS 738 SERIES PIVOT SHOWER DOOR Copyright Alumax Bath Enclosures 1997. All rights reserved. Page 1 of 8 LIMITED WARRANTY AND REMEDY Alumax Bath Enclosures warrants to its dealers,

More information

Steel Reinforced Joining Thank you for choosing Andersen. Please leave this guide with building owner.

Steel Reinforced Joining Thank you for choosing Andersen. Please leave this guide with building owner. Steel Reinforced Joining (Horizontal/Vertical) for Andersen 400 Series Woodwright & Tilt-Wash Double-Hung, Picture, and Transom Windows and 400 Series Double-Hung Half Circle and Flexiframe Specialty Windows

More information

Installation Instructions with 90 Degree Return Panel -- Model E-DP9. Model Semi-Frameless Door & Panel

Installation Instructions with 90 Degree Return Panel -- Model E-DP9. Model Semi-Frameless Door & Panel 6//5 Model Semi-Frameless Door & Panel Installation Instructions with 90 Degree Return Panel -- Model E-DP9 IF YOU NEED REPLACEMENT PARTS OR HAVE INSTALLATION QUESTIONS, PLEASE CALL OUR CUSTOMER SERVICE

More information

Model 5400H / 7000H Illustrated Installation Instructions

Model 5400H / 7000H Illustrated Installation Instructions Model 5400H / 7000H Illustrated Installation Instructions Contractors Wardrobe DESIGNERS MANUFACTURERS 261 Avenue Hall Valencia, CA 91355 (661) 257-1177 (661) 257-4907 TOLL FREE: (800) CW-DOORS (800) 293-6677

More information

Assembly Instructions

Assembly Instructions 10' and 12' Octagon Cedar Gazebo Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 06/20/09 Cedar Gazebo Assembly Instructions

More information

Step by Step Installation Instructions. Poly Shutters. Customer Service or visit us online at smithandnoble.com

Step by Step Installation Instructions. Poly Shutters. Customer Service or visit us online at smithandnoble.com Step by Step Installation Instructions Poly Shutters Customer Service 800.248.8888 or visit us online at smithandnoble.com Thank you for purchasing from smith+noble. Your new window treatments have been

More information

tile redi redi DOOR Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE:

tile redi redi DOOR Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE: redi DOOR INSTALLATION INSTRUCTIONS tile redi Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE: 1100 Door-Door Framed sliding doors RDQCI5023

More information

Casement Replacement Window Installation Instructions

Casement Replacement Window Installation Instructions Installation Instructions Installer Please leave this booklet for the homeowner after the install is completed. CAUTION - IMPORTANT Lead-based paint may be present in older homes, and the removal of windows

More information

FOR PROFESSIONAL GARAGE DOOR INSTALLERS

FOR PROFESSIONAL GARAGE DOOR INSTALLERS Composite Garage Doors Installation Instructions FOR PROFESSIONAL GARAGE DOOR INSTALLERS Tools required Screwdriver Claw Hammer Locking Pliers Power Drill Level with a 3/32" Drill Bit Utility Knife 9/16",

More information

Installer Please leave this booklet for the homeowner after the install is completed. IMPORTANT: Please read before you begin.

Installer Please leave this booklet for the homeowner after the install is completed. IMPORTANT: Please read before you begin. Hinged Patio Door Standardized Installation Instructions Aluminum Clad, Vinyl Clad, Fiberglass Clad, and Units With Wood Exterior Casings Structure With Weather Resistant Barrier Applied Before Door Installation

More information