BTB16-600BW3G, BTB16-700BW3G, BTB16-600BW3G
|
|
- Martha Holland
- 5 years ago
- Views:
Transcription
1 BTB16-600BW3G, BTB16-700BW3G, BTB16-600BW3G Pb Description Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage to 800 On-State Current Rating of 16 Amperes RMS at 80 C Uniform Gate Trigger Currents in Three Quadrants High Immunity to d/dt 1500 /µs minimum at 125 C Minimizes Snubber Networks for Protection Industry Standard TO-220AB Package Pin Out High Commutating di/dt 7.5. A/ms minimum at 125 C These are Pb Free Devices Functional Diagram CASE 221A STYLE 4 MT2 G 1 2 Additional Information Datasheet Resources Samples
2 Maximum Ratings (T J = 25 C unless otherwise noted) Rating Symbol alue Unit Peak Repetitive Off-State oltage (Note 1) (Gate Open, Sine Wave 50 to 60 Hz, T J = -40 to 125 C) BTB16 600BW3G BTB16 700BW3G BTB16 800BW3G DRM, RRM On-State RMS Current (Full Cycle Sine Wave, 60 Hz, T C = 80 C) I T (RMS) 16 A Peak Non-Repetitive Surge Current (One Full Cycle Sine Wave, 60 Hz, T C = 25 C) I TSM 170 A Circuit Fusing Consideration (t = 8.3 ms) I 2 t 120 A²sec Non Repetitive Surge Peak Off State oltage (T J = 25 C, t = 10 ms) DSM / RSM DSM / RSM +100 Peak Gate Current (T J = 125 C, t = 20ms) I GM 4.0 W Average Gate Power (T J = 125 C) P G(A) 1.0 W Operating Junction Temperature Range T J -40 to +125 C Storage Temperature Range T stg -40 to +125 C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. DRM and RRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. Thermal Characteristics Rating Symbol alue Unit Thermal Resistance, Junction to Case (AC) Junction to Ambient R 8JC R 8JA C/W Maximum Lead Temperature for Soldering Purposes, 1/8 from case for 10 seconds T L 260 C
3 Electrical Characteristics - OFF (T J = 25 C unless otherwise noted ; Electricals apply in both directions) Characteristic Symbol Min Typ Max Unit Peak Repetitive Blocking Current T J = 25 C ( D = DRM = RRM ; Gate Open) T J = 110 C I DRM, I RRM ma Electrical Characteristics - ON (T J = 25 C unless otherwise noted; Electricals apply in both directions) Characteristic Symbol Min Typ Max Unit Forward On-State oltage (Note 2) (I TM = ±17 A Peak) TM 1.55 Gate Trigger Current (Continuous dc) ( D = 12, R L = 30 Ω) MT2(+), G( ) I GT ma MT2( ), G( ) Holding Current ( D = 12, Gate Open, Initiating Current = ±100 ma) 60 ma 70 Latching Current ( D = 12, I G = 7.5 ma) I L MT2(+), G( ) 90 ma MT2( ), G( ) Gate Trigger oltage ( D = 12, R L = 30 Ω) MT2(+), G( ) GT MT2( ), G( ) Gate Non Trigger oltage (T J = 110 C) MT2(+), G( ) 0.2 GD MT2( ), G( ) Indicates Pulse Test: Pulse Width 2.0 ms, Duty Cycle 2%.
4 Dynamic Characteristics Characteristic Symbol Min Typ Max Unit Rate of Change of Commutating Current, See Figure 10. (Gate Open, T J = 125 C, No Snubber) (di/dt)c 7.5 A/ms Critical Rate of Rise of On State Current (T J = 125 C, f = 120 Hz, I G = 2 x I GT, tr 100 ns) di/dt 50 A/µs Critical Rate of Rise of Off-State oltage ( D = 0.66 x DRM, Exponential Waveform, Gate Open, T J = 125 C) d/dt 1500 /µs oltage Current Characteristic of SCR Symbol Parameter +C urrent DRM I DRM RRM Peak Repetitive Forward Off State oltage Peak Forward Blocking Current Peak Repetitive Reverse Off State oltage I RRM at RRM on state TM Quadrant 1 MainTerminal 2 + I RRM Peak Reverse Blocking Current off state + oltage I DRM at DRM TM Maximum On State oltage Holding Current Quadrant 3 MainTerminal 2 TM Quadrant Definitions for a Triac MT2 POSITIE (Positive Half Cycle) + (+) MT2 (+) MT2 Quadrant II ( ) I GT (+) I GT Quadrant I I GT +I GT ( ) MT2 ( ) MT2 Quadrant III ( ) I GT (+) I GT Quadrant I MT2 NEGATIE (Negative Half Cycle) All polarities are referenced to. With in phase signals (using standard AC lines) quadrants I and III are used.
5 Figure 1. Typical RMS Current Derating Figure 2. On-State Power Dissipation Figure 3. On State Characteristics Figure 4. Thermal Response r(t), TRANSIENT THERMAL RESISTANCE (NORMALIZED) t, TIME (ms) Figure 5. Typical Hold Current ariation
6 Figure 6. Typical Gate Trigger Current ariation Figure 7. Typical Gate Trigger oltage ariation Figure 8. Simplified Test Circuit to Measure the Critical Rate of Rise of Commutating Current (di/dt) L L 1N RMS ADJUST FOR I TM, 60 Hz AC MEASURE I CHARGE TRIGGER CHARGE CONTROL C L TRIGGER CONTROL 1N MT2 G Note: Component values are for verification of rated (di/dt)c. See AN1048 for additional information
7 Dimensions Part Marking System SEATING PLANE 4 B F T C S H Q Z A K U TO 220AB CASE 221A STYLE 4 BTB16 xbwg AYWW L G N D R J x= 6 or 8 A= Assembly Location Y= Year WW = Work Week G= Pb Free Package Pin Assignment Dim Inches Millimeters Min Max Min Max A B C D F G H J K L N Q R S T U Z Main Terminal 1 2 Main Terminal 2 3 Gate 4 Main Terminal 2 Ordering Information Device Package Shipping BTB16 600BW3G BTB16 700BW3G BTB16 800BW3G TO-220AB (Pb-Free) TO-220AB (Pb-Free) TO-220AB (Pb-Free) 50 Units / Rail 50 Units / Rail 50 Units / Rail 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at:
BTB08-600BW3G, BTB08-800BW3G
BTB08-600BW3G, BTB08-800BW3G Pb Description Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage to
More informationBTA16-600BW3G, BTA16-800BW3G,
BTA6-600BW3G, BTA6-800BW3G, Pb Description Designed for high performance full wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage to
More informationBTA30H-600CW3G, BTA30H-800CW3G
BTA30H-600CW3G, BTA30H-800CW3G Pb Description Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage
More informationBTA08-800CW3G. Thyristors. Surface Mount 800V > BTA08-800CW3G. Description
BTA08-800CW3G Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Features Blocking oltage to 800 On-State
More informationBTA25-600CW3G, BTA25-800CW3G
BTA25-600CW3G, BTA25-800CW3G Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Features Blocking oltage
More informationMAC8DG, MAC8MG, MAC8NG
MAC8DG, MAC8MG, MAC8NG Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled,
More informationMAC16DG, MAC16MG, MAC16NG
MAC6DG, MAC6MG, MAC6NG Pb Description Designed for high performance full wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking Voltage to 800
More informationMAC12HCDG, MAC12HCMG, MAC12HCNG
MAC2HCDG, MAC2HCMG, MAC2HCNG Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls or dimmers; or wherever full wave, silicon gate controlled
More informationMAC12D, MAC12M, MAC12N
MAC12D, MAC12M, MAC12N Pb Description Designed for high performance full wave ac control applications where high noise immunity and commutating di/dt are required. Features Blocking Voltage to 800 Volts
More informationMC4DCM, MAC4DCN. Thyristors. Surface Mount 600V - 800V > MC4DCM, MAC4DCN. Description
MCDCM, MACDCN Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Small Size Surface
More informationMAC228A. Thyristors. Surface Mount 400V - 800V > MAC228A. Description
MAC228A Pb Description Designed primarily for industrial and consumer applications for full wave control of AC loads such as appliance controls, heater controls, motor controls, and other power switching
More informationMCR8NG. Thyristors. Surface Mount 600V - 800V > MCR8NG. Description
Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled devices are needed.
More informationMAC210A8, MAC210A10. Thyristors. Surface Mount 400V - 800V > MAC210A8, MAC210A10. Description
MAC210A8, MAC210A10 Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full wave silicon gate
More informationBTA16-600CW3G, BTA16-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 600 thru 800 VOLTS
BTA6-600CW3G, BTA6-800CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance fullwave ac control applications where high noise immunity and high commutating di/dt are required. Features
More informationC122F1G. Thyristors. Surface Mount 50V > C122F1G. Description
Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled, solid state devices
More informationBTB16-600BW3G, BTB16-700BW3G, BTB16-800BW3G. Triacs. Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 600 thru 800 VOLTS
BTB-BW3G, BTB-7BW3G, BTB-8BW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required.
More informationBTA08-800CW3G. Triacs. Silicon Bidirectional Thyristors TRIACS 8 AMPERES RMS 800 VOLTS
BTA8-8CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage
More informationBTB16-600CW3G, BTB16-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 600 thru 800 VOLTS
BTB-CW3G, BTB-8CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking
More information2N6400. Thyristors. Surface Mount V > 2N6400. Description
2N6400 Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled, solid state devices
More informationBTA25H-600CW3G, BTA25H-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 25 AMPERES RMS 600 thru 800 VOLTS
BTAH-600CW3G, BTAH-800CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features
More informationMCR25DG, MCR25MG, MCR25NG
MCR25DG, MCR25MG, MCR25NG Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled
More informationBTA16-600CW3G, BTA16-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 600 thru 800 VOLTS
BTA6-600CW3G, BTA6-800CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance fullwave ac control applications where high noise immunity and high commutating di/dt are required. Features
More informationBTA25-600CW3G, BTA25-800CW3G. Triacs Silicon Bidirectional Thyristors. TRIACS 25 AMPERES RMS 600 thru 800 VOLTS
BTA-6CW3G, BTA-8CW3G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features
More informationMCR218-2G, MCR218-4G, MCR218-6G
MCR218-2G, MCR218-4G, MCR218-6G Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half-wave silicon gate-controlled,
More informationMCR69-2, MCR69-3. Thyristors. Surface Mount V > MCR69-2, MCR69-3. Description. Designed for overvoltage protection in crowbar circuits.
1 2 3 Thyristors MCR69-2, MCR69-3 Pb Description Designed for overvoltage protection in crowbar circuits. Features Glass-Passivated Junctions for Greater Parameter Stability and Reliability Center-Gate
More informationMCR12DG, MCR12MG, MCR12NG
MCR12DG, MCR12MG, MCR12NG Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled,
More informationMCR8SDG, MCR8SMG, MCR8SNG
MCR8SDG, MCR8SMG, MCR8SNG Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled
More information2N6394. Thyristors. Surface Mount V > 2N6394. Description
2N6394 Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies. Features Glass Passivated Junctions for Greater Parameter Uniformity
More informationMAC08BT1, MAC08MT1. Thyristors. Surface Mount 200V - 600V > MAC08BT1, MAC08MT1. Description
MAC08BT1, MAC08 Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Sensitive
More informationT2322B. Thyristors Surface Mount 200V > T2322B TO 225AA CASE 77 STYLE 2. Description
T2322B Pb Description Designed primarily for ac power switching. The gate sensitivity of these triacs permits the use of economical transistorized or integrated circuit control circuits, and it enhances
More informationMCR8DCM, MCR8DCN. Thyristors. Surface Mount 600V - 800V > MCR8DCM, MCR8DCN G K. Description
MCR8DCM, MCR8DCN Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Small Size
More information2N6504 Series. Thyristors. Surface Mount V > 2N6504 Series. Description
2N6504 Series Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Features Glass Passivated Junctions for
More informationBTA12-600C4G, BTA12-800C4G. Triacs Silicon Bidirectional Thyristors. TRIACS 12 AMPERES RMS 600 thru 800 VOLTS
BTA12-6C4G, BTA12-8C4G Triacs Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features
More informationMCR8DSM, MCR8DSN. Thyristors. Surface Mount 600V - 800V > MCR8DSM, MCR8DSN G K. Description
MCR8DSM, MCR8DSN Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Small Size
More information2N6344. Thyristors. Surface Mount V > 2N6344. Description
2N6344 Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full-wave silicon gate controlled
More informationC106 Series. Thyristors. Surface Mount > V > C106 Series TO 225AA CASE 77 STYLE 2. Description
C106 Series Pb Description Glassivated PNPN devices designed for high volume consumer applications such as temperature, light, and speed control; process and remote control, and warning systems where reliability
More informationMCR12DCM, MCR12DCN. Thyristors. Surface Mount 400V - 800V > MCR12DCM, MCR12DCN G K. Description
MCR12DCM, MCR12DCN Pb Description This thyristor is designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon
More information2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
More information2N6344. Silicon Bidirectional Thyristors. TRIACS 8 AMPERES RMS 600 thru 800 VOLTS
Preferred Device Triacs Silicon Bidirectional Thyristors Designed primarily for full-wave ac control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever
More informationMCR12DSM, MCR12DSN. Thyristors. Surface Mount 100V -600V > MCR12DSM, MCR12DSN G K. Description
MCR12DSM, MCR12DSN Thyristors Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control; CDI (Capacitive
More information2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
More informationMCR703A Series. Thyristors. Surface Mount 100V -600V > MCR703A Series G K. Description
MCR703 Series Pb Description PNPN devices designed for high volume, low cost consumer applications such as temperature, light and speed control; process and remote control; and warning systems where reliability
More information2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
More informationMAC15 Series. Triacs. Silicon Bidirectional Thyristors. TRIACS 15 AMPERES RMS 400 thru 800 VOLTS
MAC5 Series Triacs Silicon Bidirectional Thyristors Designed primarily for full-wave ac control applications, such as solidstate relays, motor controls, heating controls and power supplies; or wherever
More informationMCR70xA Series. Thyristors. Surface Mount 100V -600V > MCR70xA Series G K. Description
MCR70x Series Pb Description PNPN Componants designed for high volume, low cost consumer applications such as temperature, light and speed control; process and remote control; and warning systems where
More informationMCR106-6, MCR Thyristors. Surface Mount 400V - 600V > MCR106-6, MCR106-8 TO 225AA CASE 77 STYLE 2 G K. Description
MCR106-6, MCR106-8 Pb Description PNPN devices designed for high volume consumer applications such as temperature, light and speed control; process and remote control, and warning systems where reliability
More informationMAC3030 8G. Triacs. Silicon Bidirectional Thyristors TRIACS 8.0 AMPERES RMS 250 VOLTS
Triacs Silicon Bidirectional Thyristors Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever fullwave silicon
More information2N6344A, 2N6348A, 2N6349A
2N6344A, 2N6348A, 2N6349A Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full-wave silicon
More informationMCR08B, MCR08M. Thyristors. Surface Mount 600V - 800V > MCR08B, MCR08M G K. Description
MCR8B, MCR8M Pb Description PNPN devices designed for line powered consumer applications such as relay and lamp drivers, small motor controls, gate drivers for larger thyristors, and sensing and detection
More informationMAC4DCM, MAC4DCN. Triacs. Silicon Bidirectional Thyristors TRIACS 4.0 AMPERES RMS VOLTS
Preferred Device Triacs Silicon Bidirectional Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control.
More informationMAC4DSM, MAC4DSN. Triacs. Silicon Bidirectional Thyristors TRIACS 4.0 AMPERES RMS VOLTS
Triacs Preferred Device Silicon Bidirectional Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control.
More information2N6071A/B Series. Thyristors. Surface Mount 200V-600W > 2N6071A/B Series. Description
2N6071A/B Series Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full-wave silicon gate
More informationMAC223A6, MAC223A8, MAC223A10. Triacs. Silicon Bidirectional Thyristors. TRIACS 25 AMPERES RMS 400 thru 800 VOLTS
MAC3A6, MAC3A8, MAC3A Triacs Preferred Device Silicon Bidirectional Thyristors Designed primarily for full-wave ac control applications such as lighting systems, heater controls, motor controls and power
More informationMAC16D, MAC16M, MAC16N. Triacs. Silicon Bidirectional Thyristors. TRIACS 16 AMPERES RMS 400 thru 800 VOLTS
MAC6D, MAC6M, MAC6N Triacs Preferred Device Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required.
More informationSilicon Bidirectional Thyristors
Preferred Device Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Blocking Voltage to
More informationC106 Series. Sensitive Gate Silicon Controlled Rectifiers
Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Glassivated PNPN devices designed for high volume consumer applications such as temperature, light, and speed control; process and
More informationSilicon Controlled Rectifiers
MCR692, MCR693 Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed for overvoltage protection in crowbar circuits. Features Glass-Passivated Junctions for Greater Parameter Stability and
More informationMCR8N. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 8 AMPERES RMS 600 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever
More information2N6400 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 16 AMPERES RMS 50 thru 800 VOLTS
Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever halfwave silicon
More informationMAC4DCM, MAC4DCN. Triacs. Silicon Bidirectional Thyristors TRIACS 4.0 AMPERES RMS VOLTS
Preferred Device Triacs Silicon Bidirectional Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control.
More information2N6504 Series. Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 25 AMPERES RMS 50 thru 800 VOLTS
Preferred Device Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits.
More informationBTA40 and BTA/BTB41 Series
STANDARD 4A TRIACS MAIN FEATURES: Symbol Value Unit I T(RMS) 4 A G V DRM /V RRM 6 and 8 V A1 A1 I GT (Q1 ) 5 ma G DESCRIPTION Available in high power packages, the BTA/ BTB4-41 series is suitable for general
More informationSymbol Parameter Conditions Ratings Unit. 600 V Sine wave, 50/60Hz, Gate open V RRM Repetitive Peak Reverse Voltage 600 V I T(AV)
3 Quadrants Standard TRIAC V DRM = 6V I T(RMS) = 4 A I TSM = 4 A I GT = 5mA FEATURES Repetitive Peak Off-State Voltage : 6V R.M.S On State Current (I T(RMS) = 4A) Gate Trigger Current : 5mA High commutation
More informationDescription. Features. Strobes and Flashers. Ignitors. High Voltage Regulators. Pulse Generators. Functional Diagram. Additional Information
MKP3V120, MKP3V240 Pb Description Bidirectional devices designed for direct interface with the ac power line. Upon reaching the breakover voltage in each direction, the device switches from a blocking
More informationMCR100 Series Preferred Device. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 0.8 A RMS 100 thru 600 V
MCR0 Series Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors PNPN devices designed for high volume, line-powered consumer applications such as relay and lamp drivers,
More informationZ0107MA TRIACS 1.0 AMPERE RMS 600 VOLTS
Z7MA Sensitive ate Triacs Series Silicon Bidirectional Thyristors Designed for use in solid state relays, MPU interface, TTL logic and any other light industrial or consumer application. Supplied in an
More informationT2550H-600T 25A TRIACS MAIN FEATURES:
SNUBBERLESS HIGH TEMPERATURE 25A TRIACS MAIN FEATURES: Symbol Value Unit I T(RMS) 25 A V DRM /V RRM 600 V I GT (Q1 ) 50 ma DESCRIPTION Specifically designed for use in high temperature environment (found
More informationMCR8DSM, MCR8DSN. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 8 AMPERES RMS VOLTS
Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Designed for high volume, low cost, industrial and consumer applications such as motor control; process control;
More informationSymbol Parameter Conditions Ratings Unit. 600 V Sine wave, 50/60Hz, Gate open V RRM Repetitive Peak Reverse Voltage 600 V I T(AV)
3 Quadrants Standard TRIAC V DRM = 6 V I T(RMS) = 5 A I TSM = 6 A I GT = 35mA FEATURES Repetitive Peak Off-State Voltage : 6V R.M.S On State Current (I T(RMS) = 5A) Gate Trigger Current : 35mA High commutation
More informationT x V 25 A Snubberless Triac. Description. Features. Applications. Benefits
1200 V 25 A Snubberless Triac Description Datasheet production data Its 1200 V blocking voltage enables use in 3-phase industrial application. Its noise immunity and dynamic commutation makes it suitable
More informationSilicon Bidirectional Thyristors
Preferred Device Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Blocking Voltage to
More informationT1635T-8FP. 16 A Snubberless Triac. Features. Applications. Description
16 A Snubberless Triac G A A1 Features Datasheet production data Medium current Triac High static and dynamic commutation Three quadrants ECOPACK compliant component Complies with UL standards (File ref:
More informationSilicon Bidirectional Thyristors
Preferred Device Silicon Bidirectional Thyristors Designed for use in solid state relays, MPU interface, TTL logic and any other light industrial or consumer application. Supplied in an inexpensive TO92
More informationPhase Control SCR, 70 A
Phase Control SCR, 70 A 70TPS..PbF High oltage Series ishay High Power Products 2 (A) DESCRIPTION/FEATURES The 70TPS..PbF High oltage Series of silicon controlled rectifiers are specifically designed for
More informationNYE08-10B6TG. Protected TRIAC
NYE8-B6TG Protected TRIAC Silicon Bidirectional Thyristor Designed for use in solid state relays, MPU interface, TTL logic and any other light industrial or consumer application. Supplied in an inexpensive
More informationACST1635-8FP. Overvoltage protected AC switch. Description. Features. Applications
Overvoltage protected AC switch Description Datasheet production data Features OUT COM TO-220FPAB Enables equipment to meet IEC 61000-4-5 surge with overvoltage crowbar technology High noise immunity against
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. C6 Series Preferred Devices Sensitive Gate Silicon Controlled Rectifiers
More informationACST1635-8FP. 16 A overvoltage protected AC switch. Datasheet. Features. Application. Description
Datasheet 16 A overvoltage protected AC switch Features O-22FPAB OU G OU Enables equipment to meet IEC 61-4-5 surge with overvoltage crowbar technology High noise immunity against static d/dt and IEC 61-4-4
More informationThyristors Surface Mount 120V - 240V > MKP1V120 Series. Description. Features. Strobes and Flashers. Ignitors. High Voltage Regulators
MKP1V120 Series Pb Description Bidirectional devices designed for direct interface with the ac power line. Upon reaching the breakover voltage in each direction, the device switches from a blocking state
More informationT3035H-8I. 30 A V TO-220AB insulated H-series Snubberless Triac. Datasheet. Features. Applications. Description. TO-220AB insulated
Datasheet 3 A - 8 V TO-22AB insulated H-series Snubberless Triac G A2 A1 Features 3 A high current Triac 8 V symmetrical blocking voltage 15 C maximum junction temperature T j Three triggering quadrants
More informationBTA10, BTB10 T1035, T1050 Datasheet
BTA10, BTB10 T1035, T1050 Datasheet 10 A Snubberless, logic level and standard Triacs Features Medium current Triac G A1 Low thermal resistance with clip bonding Low thermal resistance insulation ceramic
More informationQJxx16xHx Series. Thyristors 16 Amp High Temperature Alternistor Triacs. RoHS. Description
RoHS Description This 16A high temperature alternistor triac solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature modulation controls,
More informationMCR106-6, MCR Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 4 AMPERES RMS 400 thru 600 VOLTS
MCR106-6, MCR106-8 Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors PNPN devices designed for high volume consumer applications such as temperature, light and speed
More informationC106 Series. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 4 A RMS, Volts
C6 Series Preferred Devices Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors Glassivated PNPN devices designed for high volume consumer applications such as temperature, light,
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD DESCRIPTION Passivated, sensitive gate triacs in a plastic envelope, intended for use in general purpose bidirectional switching and phase control applications, where high
More informationBTA40 and BTA/BTB41 Series
BTA4 and BTA/BTB41 Series STANDARD 4A TRIACS MAIN FEATURES: Symbol Value Unit I T(RMS) 4 A G V DRM /V RRM 6 and 8 V A1 A1 I GT (Q1 ) 5 ma G DESCRIPTION Available in high power packages, the BTA/ BTB4-41
More informationT405Q A sensitivetriacs. Description. Features. Applications
4 A sensitivetriacs G A2 A1 Description Datasheet - production data Sensitive Triacs are intended in general purpose applications where high surge current capability is required. These Triacs feature a
More informationTwo Separated Thyristor Module, 100A ( Low Profile Package ) 14, 15 I T(AV) CHARACTERISTICS to to 150
NKTA Series Two Separated Thyristor Module, A ( Low Profile Package ) FEATURES High voltage RMS isolating voltage High surge capability Planar SCR chips Heat transfer and isolation through direct copper
More informationT8M35T-B SERIES TRIACS 8 AMPERES RMS 600 VOLTS. Triacs Sillicon Bidirectional Thyristors TO-220AB FEATURES MECHANICAL DATA
LITE-ON SEMICONDUCTOR Triacs Sillicon Bidirectional Thyristors TRIACS 8 AMPERES RMS 600 VOLTS FEATURES Blocking Voltage to 600 Volts On-State Current Rating of 8.0 Amperes RMS at 0 Uniform Gate Trigger
More informationT1610, T1635, T1650 BTA16, BTB16 Datasheet
T1610, T1635, T1650 BTA16, BTB16 Datasheet Snubberless, logic level and standard 16 A Triacs A2 Features Medium current Triac A2 G A1 Low thermal resistance with clip bonding Low thermal resistance insulation
More informationBTA10 and BTB10 Series
BTA and BTB Series SNUBBERLESS & STANDARD A TRIACS Table : Main Features Symbol Value Unit I T(RMS) A V DRM /V RRM 6 and 8 V G A I GT (Q ) 5 to 5 ma DESCRIPTION Available either in through-hole or surface-mount
More information1.5SMCxxAT3G. TVS Diodes. Surface Mount > 1500W > 1.5SMCxxAT3G. Cathode. Anode. Uni-directional. Description
1.5SMCxxAT3G Pb Description The 1.5SMCxxAT3G series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge capability,
More informationBTA40 and BTA/BTB41 Series
STANDARD 4A TRIACS MAIN FEATURES: Symbol Value Unit I T(RMS) 4 A G V DRM /V RRM 6 and 8 V A1 A1 I GT (Q1 ) 5 ma G DESCRIPTION Available in high power packages, the BTA/ BTB4-41 series is suitable for general
More informationACST310-8B. Overvoltage protected AC switch. Description. Features. Applications. Benefits
Overvoltage protected AC switch Datasheet production data Features AC switch with self over voltage protection Microcontroller direct driven (low gate current max. 10 ma) Three quadrants (Q1, Q2 and Q3)
More information1.5SMC6.8AT3G. TVS Diodes. Surface Mount > 1500W > 1.5SMC6.8AT3G. Bi-directional. Cathode. Anode. Uni-directional. Description
1.5SMC6.8AT3G Pb Description The 1.5SMC6.8AT3G series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge
More information2N5060 Series Preferred Device. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors
Preferred Device Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors nnular PNPN devices designed for high volume consumer applications such as relay and lamp drivers, small motor
More informationACS120. Overvoltage protected AC switch (ACS ) Applications. Description. Features. Benefits
Overvoltage protected AC switch (ACS ) Applications Datasheet - production data Features Blocking voltage: V DRM / V RRM = +/- 700 V Avalanche controlled: V CL typ. = 1100 V Nominal conducting current:
More informationBTA A Snubberless Triacs. Features. Description. I T(RMS) = 20 A V DRM, V RRM = 600 and 700 V I GT (Q1) (max) = 35 and 50 ma
20 A Snubberless Triacs Datasheet production data Features I T(RMS) = 20 A V DRM, V RRM = 600 and 700 V I GT (Q1) (max) = 35 and 50 ma Description G A2 A1 The Triacs use high performance glass passivated
More informationUNISONIC TECHNOLOGIES CO., LTD
MCR00 UNISONIC TECHNOLOGIES CO., LTD SENSITIVE GATE SILICON CONTROLLED RECTIFIERS REVERSE BLOCKING THYRISTORS 3 2 SOT-23 SOT-223 DEIPTION PNPN devices designed for high volume, line-powered consumer applications
More informationMKP1V120 Series. Sidac High Voltage. Bidirectional Triggers 0.9 AMPERES RMS VOLTS
MKP112 Series Sidac High oltage Bidirectional Triggers Bidirectional devices designed for direct interface with the ac power line. Upon reaching the breakover voltage in each direction, the device switches
More information