18" 1.5" 3"R 11.5" 10" 3-1/2" MINIMUM STONE CUSHION GRADATION CA-6

Transcription

1

2

3 18" 1.5" 3"R 1.5" 4"R 1" 11.5" 10" 13.5" 5" 3-1/2" MINIMUM STONE CUSHION GRADATION CA-6 NOTES: 1. REINFORCEMENT: PROVIDE TWO (2) #4 REINFORCING BARS CONTINUOUS BETWEEN EXPANSION JOINTS, WITH LOCATION SPACING AS INDICATED ABOVE. 2. EXPANSION JOINT: 3/4" THICK BITUMINOUS FILLER MATERIAL- PROVIDE TWO (2) #6 X 24" SMOOTH BARS WITH EXPANSION CAPS AT EACH EXPANSION JOINT. INSTALL AT ENDS OF ALL RADII AND NO FURTHER THAN SIXTY (60') FEET APART. 3. SAW THREE (3) EQUALLY SPACED CONTRACTION JOINTS AT TWENTY (20') FEET INTERVALS BETWEEN EXPANSION JOINTS. CONTRACTION JOINTS SHALL BE SAW- CUT IN THE UPPER ONE-THIRD OF CURB AND GUTTER WITHIN 3 DAYS OF PLACEMENT. 4. COST OF BARS SHALL BE INCLUDED IN THE UNIT PRICE (PER LINEAL FOOT) FOR CURB AND GUTTER. CURB.DWG CURB AND GUTTER DETAIL (RESIDENTIAL) Village of STREET & PAVEMENT rjr ktl DRAWING NO. STR-03

4 1" 1/2" PRE-MOLDED NON-EXTRUDING JOINT FILLLER AT EXPANSION JOINTS (MAXIMUM 50' SPACING) 2" R "A" SEE NOTE 3 0.5" 1/8" R (TYP) DEPRESSED 1.5" PAVEMENT THICKNESS 3.5" 5.0" "A" 2" MINIMUM STONE CUSHION GRADATION CA-6 -IF FORMED BY HAND EXPANSION CAP SECTION "A-A" X-SECTION NOTE: 1. PROVIDE TWO #4 BARS (10' LONG) CENTERED IN EACH UTILITY TRENCH. 2. COST OF BARS SHALL BE INCLUDED IN THE UNIT PRICE (PER LINEAL FOOT) FOR CURB. 3. PROVIDE TWO #6 SMOOTH BARS W/EXPANSION CAPS AT EACH EXPANSION JOINT. 4. CONTRACTION JOINTS - TWO CONTRACTION JOINTS SHALL BE PLACED AT EQUAL SPACES BETWEEN NORMAL EXPANSION JOINTS. CONTRACTION JOINTS SHALL BE SAW CUT IN THE UPPER 1/3 OF CURB WITHIN 7 DAYS OF PLACEMENT. B-6.DWG Village VERTICAL CURB (TYPE B) of STREET & PAVEMENT DRAWING NO. STR-05

5 19" 1" 12" R=2" PITCH R=3" REINFORCEMENT 7" 15" 10" EXPANSION JOINT 4" 3" 6.5" 6.5" 3" NOTES: 1. REINFORCEMENT SHALL BE THREE (3) #5 REINFORCING BARS CONTINUOUS BETWEEN EXPANSION EXPANSION JOINTS, WITH LOCATION SPACING AS INDICATED ABOVE. 2. EXPANSION JOINT: 3/4" THICK BITUMINOUS FILLER MATERIAL- PROVIDE TWO (2) #6 X 24" SMOOTH BARS WITH EXPANSION CAPS AT EACH EXPANSION JOINT. INSTALL AT ENDS OF ALL RADII AND NO FURTHER THAN SIXTY (60') FEET APART. 3. SAW THREE (3) EQUALLY SPACED CONTRACTION JOINTS AT TWENTY (20') FEET INTERVALS BETWEEN EXPANSION JOINTS. CONTRACTION JOINTS SHALL BE SAW- CUT IN THE UPPER ONE-THIRD OF CURB AND GUTTER WITHIN 3 DAYS OF PLACEMENT. 4. COST OF BARS SHALL BE INCLUDED IN THE UNIT PRICE (PER LINEAL FOOT) FOR CURB AND GUTTER. B CURB AND GUTTER B-612.DWG STREET & PAVEMENT rjr KTL DRAWING NO. STR-04

6 C L R.O.W. & STREET 30' 30' GAS MAIN P.C.C. CURB & GUTTER 8' 3' MIN 7' 11' 6' MIN. W.M. 6' MILL 15' 13.5' BINDER TO FLAGGING OF CURB 15' 4" CROWN 1 1/2" BITUMINOUS CONCRETE SURFACE COURSE CLASS I 3" BITUMINOUS CONCRETE BINDER COURSE 9" AGGREGATE BASE COURSE TYPE B CA 6 (CRUSHED STONE) PVC UNDERDRAIN VARIES 5' SANITARY SEWER 9' 1' 5'x5" P.C.C. SIDEWALK 2" SAND OR STONE CUSHION Binder Course The binder course on all public roadways shall be initially constructed flush with the top of the front of the curb. The finished grade of the binder cross-section will allow water to flow unobstructed from the asphalt to the gutter of the curb. The additional binder placed along the front of curb will be removed by milling before placement of the final surface course. Street_Xsection-Rev1.dwg Village TYPICAL STREET SECTION (RESIDENTIAL) STREET & PAVEMENT of DRAWING NO. 11/20/06 STR-01

7 1 1/2" 3" BITUMINOUS SURFACE CLASS I BITUMINOUS BINDER CLASS I 9" CRUSHED STONE BASE GRADATION CA-6 PAVEMENT SECTION 30' B TO B ROADWAY PAVE.DWG STREET & PAVEMENT DRAWING NO. STR-02

8 8'-0" 1" Bituminuous Asphalt Surface Course 1-1/2" BituminuousAsphalt Binder Course Slope 1/4" per foot Aggregate Stone Base FILE NAME: Bike Path.dwg Pedestrian Bike Path Street Improvement WDC DRAWING NO.

9 HYDRANT - (E.J.I.W. WATERMASTER 5BR250) PAINTED SAFETY YELLOW BREAKABLE FLANGE AND COUPLING " AND " HOSE NOZZLE ALL WITH NATIONAL STANDARD THREADS 3' 10' MAX. 4-1/2" NOZZLE SPECIAL STAY - PUT COVER W/ WORD "WATER" ON COVER 2-1/2" NOZZLE BREAK FLANGE 2" 18" - 24" MIN-MAX CAST IRON VALVE BOX 5' MIN. COVER 8' MAX. COVER GATE VALVE - MIN. TURN LEFT TO OPEN VALVE STABLILIZER BOX DUCTILE IRON PIPE CONNECT TO ANCHORING TEE 1" RIVER ROCK 1/2 C.Y. MINIMUM VARIES 1" RIVER ROCK 1/2 C.Y. MINIMUM PROVIDE CONCRETE BASE AND BLOCKING AGAINST UNDISTURBED EARTH PRECAST CONCRETE BLOCK Notes: 1. If depth of main is greater than 8' then the hydrant and auxiliary valve must be brought to the proper depth using 90 degree bends. 2. Adjustments to existing or proposed hydrants shall not exceed a total of 3'. See Note #1 for adjustments that have a total of adjustments greater than 3' /32" 6 1/2" 4" 6 1/2" 2 3/4" 10 15/32" VALVE STABILIZER DETAIL BR5_HYDRANT DWG Village HYDRANT of INSTALLATION WATER MAIN 4/24/06 wdc 11/29/07 DRAWING NO. WM-06

10 MORTAR MJ BUTTERFLY VALVE OPENING ABOVE VALVE OPERATOR WITH 2" A.W.W.A. OPERATING NUT 1'-0" 8" MAX. PRECAST REINF. CONCRETE. SEE I.D.O.T. STD STD. VALVE VAULT FRAME & COVER PER VILLAGE STANDARDS ADJUSTING RINGS AS REQUIRED ( MAX., 2 RINGS MAX.) 5'- COVER 5" 6'-0" DIA. Min. 5" 8" 8" PRECAST REINFORCED CONCRETE BASE SLAB ON A STONE CUSHION BUTTERFLY VALVE VAULT BTTRFLY.DWG Village of WATER MAIN DRAWING NO. 2/24/05 WM-04

11 CASING/STEEL SLEEVE (PER ANSI B36.10) PEA GRAVEL PLUG ENDS CASING CHOCK CARRIER PIPE SUPPORT CARRIER/CONDUIT PIPE (WATER OR SEWER MAIN) CASING SCALE: DETAIL N.T.S. Casing Notes: 1. Casing pipe shall be welded steel pipe meeting ASTM A Minimum thickness = 3/8 inch. 3. Joints should be continuous field-welded butt joints per AWWA C The casing pipe shall conform to ANSI B The carrier pipe support system shall be Cascade Water Works stainless steel spacers, or approved equal, installed at 10 foot intervals through the casing pipe. 6. Casing ends shall be sealed with a non-shrink grout cap. 7. All annular space between the carrier pipe and casing pipe shall be filled with pea gravel. 8. If voids are created around the exterior of the casing pipe, they shall be filled with Mearl Geoform liquid concentrate low density cellular concrete grout having a minimum density of 45 pounds per cubic foot and a minimum compressive strength at 28 days of 160 pounds per square inch. CASING DETAIL Casing Detail.dwg DRAWN BY: STREET & PAVEMENT Public Works Department 10/30/2007 DRAWING NO. STR-?

12 CASTING AS SPECIFIED MASTIC MAX. PRECAST CONC. 2 ADJUSTING RINGS 24" ONE PIPE LENGTH 8" 1 O.C. ELEV. SHOWN ON PLAN 2'- ECCENTRIC CONE SECTION VARIABLE MORTAR TYP. 5" 48" DIAMETER 3 MIN. RUBBER BOOT PER ASTM C-923 PRECAST REINFIRCED CONCRETE SECTIONS 3/4" LIMESTONE (NO FINES) NOTES: PRECAST REINFORCED CONCRETE C.B. BOTTOM WITH INTEGRAL SIDEWALL 1. Adjustment: Any structure located within pavement shall require the use of at least one (1) rubber adjustment riser, Infra-Riser brand or approved equal, and, if necessary, said riser shall be of the tapered type in order to match the proposed grade of the roadway. No more than two (2) precast concrete adjusting rings with six (6) inch maximum height adjustment shall be allowed. Adjustments within pavement that are less than three (3) inches in height shall consist of only rubber adjustment riser(s). The minimum thickness of a rubber adjustment riser shall be one (1) inch. Adjustments within pavement greater than three (3) inches in height shall use a minimum three (3) inch precast concrete riser for the lower riser, and the final riser shall be of the rubber type. 2. Pipe and frame seals: All pipe connection openings shall be precast with resilient rubber water tight pipe to manhole sleeves or seals conforming to ASTM C-923. Adapter chimney seal with twelve (12) inch sleeve type shall extend from the manhole cone to the manhole frame for all structures in the right-of-way. 3. Sealing: All mating surfaces of adjustment riser(s), structure sections, and frames shall be sealed with a mastic sealant. No concrete mortar or epoxy shall be allowed as a sealant for adjustment risers, structure sections or frames. If multiple adjustment risers are required, a continuous application of sealant shall be applied between each unit. 4. All bottom sections shall be monolithically precast including bases and invert flowlines. 5. Provide CA-6 aggregate backfill around catch basin to subgrade elevation in paved areas.for subgrade. CBASIN_A.DWG Village of CATCHBASIN TYPE A STORM SEWER DRAWING NO. STS-02

13 MASTIC CASTING AS SPECIFIED MAX. PRECAST CONC. 2 ADJUSTING RINGS 3" 24" DIA. MORTAR ELEV. SHOWN ON PLAN RUBBER BOOT PER ASTM C-923 4" 18" MIN. 3/4" LIMESTONE (NO FINES) PRECAST REINFORCED CONCRETE C.B. BOTTOM WITH INTEGRAL SIDEWALL NOTES: 1. Adjustment: Any structure located within pavement shall require the use of at least one (1) rubber adjustment riser, Infra-Riser brand or approved equal, and, if necessary, said riser shall be of the tapered type in order to match the proposed grade of the roadway. No more than two (2) precast concrete adjusting rings with six (6) inch maximum height adjustment shall be allowed. Adjustments within pavement that are less than three (3) inches in height shall consist of only rubber adjustment riser(s). The minimum thickness of a rubber adjustment riser shall be one (1) inch. Adjustments within pavement greater than three (3) inches in height shall use a minimum three (3) inch precast concrete riser for the lower riser, and the final riser shall be of the rubber type. 2. Pipe and frame seals: All pipe connection openings shall be precast with resilient rubber water tight pipe to manhole sleeves or seals conforming to ASTM C-923. Adapter chimney seal with twelve (12) inch sleeve type shall extend from the manhole cone to the manhole frame for all structures in the right-of-way. 3. Sealing: All mating surfaces of adjustment riser(s), structure sections, and frames shall be sealed with a mastic sealant. No concrete mortar or epoxy shall be allowed as a sealant for adjustment risers, structure sections or frames. If multiple adjustment risers are required, a continuous application of sealant shall be applied between each unit. 4. All bottom sections shall be monolithically precast including bases and invert flowlines. 5. Provide CA-6 aggregate backfill around catch basin to subgrade elevation in paved areas.for subgrade. CBASIN_C.DWG Village of CATCHBASIN TYPE C STORM SEWER DRAWING NO. STS-04

14 1.5:1 OR FLATTER 3" BAR-h OR h1 ETC. 1.5 OR 2 PIPE CULVERT h V B 12 CTS. #4 BARS V INSIDE DIA. OF 12 CTS. #4 BARS V MIN. UNDER PIPE 2' 1'- 2" C.L. 18" CTS. SECTION A-A END VIEW a b b F BARS h TO h9 BEND IN FIELD ONE REQ'D IN EACH HEADWALL 45 18" BAR V D 2.5" A V E 18" MARK H H1 H2 H3 H4 H5 H6 H7 H8 H9 a 1'-10" 1'-10" 2'-1" 2'-1" 2'-9" 2'-9" 3'-3" 3'-3" 3'-11" 3'-11" b 2'-5.5" 3'-2.5" 2'-5.5" 3'-2.5" 3'-3" 4'-1.5" 3'-10.5" 4'-10.5" 4'-8" 5'-9.5" PLAN NOTE: CLASS-X-CONCRETE SHALL BE USED THROUGHOUT DESIGN NO. D D15-2 D D18-2 D D24-2 D D30-2 D D36-2 INSIDE DIA. OF PIPE 15" 15" 18" 18" 24" 24" 30" 30" 3 3 SLOPE OF FILL* A 1.5:1 2:1 1.5:1 2:1 1.5:1 2:1 1.5:1 2:1 1.5:1 2:1 1'-7" 10" 2'-2" 10" 6'-7.5" 3'-3.25" 1.2 1'-7" 1'-1" 2'-2" 2'-3" 5'-8.5" 2'-5.5" 1.0 2'-2" 1'-1" 2'-2" 2'-3" 6'-10.5" 3'-3.25" 1.3 2'-1" 1'-4" 2'-9" 2'-11" 7'-4.5" 3'-2" 1.5 2'-10" 1'-4" 2'-9" 2'-11" 8'-10.5" 4'-2.5" 2.0 2'- 1'-7" 3'-3" 3'-5" 8'-8.5" 3'-9" 3'-4" 3' 4' B 1'-7" 1'-10" C 3'-3" 3'-10" DIMENSIONS D 1'-11" 2' 1'-11" 2' CL.XCON 2 HDWLS E F CU. YDS 5'-5.5" 2'-5.5" 0.9 3'-5" 10'-4.5" 4'11" 4'-1" 10'-4.5" 4'-5.5" '-10" 3'-10" 4'-1" 12'-4.5" 5'-10.5" 3.5 REINFORCEMENT BARS H-BARS V-BARS MARK LENGTH NO. H 6'-9" H1 H2 H3 H4 H5 H6 H7 H8 H9 8'-3" 7' 8'- 9'-3" 11' 11' 13' 13'-3" 15' TOTAL WT. 2 HDWLS * IF EMBANKMENT SLOPE ABOVE HEADWALL IS FLATTER THAN 2:1, PROVIDE WINGS FOR 2:1 SLOPE. HEADWALL.DWG Village REINFORCED CONCRETE HEADWALL STORM SEWER of DRAWING NO. STS-09

15 RESIDENTIAL STREET LIGHT CONCRETE FOUNDATION DETAIL Extruded 4"x8" Reinforced Handhole with Ground Lug attached to frame 1" Chamfer 8" 2' 1'- 4" 3" PVC Rigid Raceway 1x36x4 Anchor Bolts Fdn. Cage #3 12" O.C., 1 Dia. Attached to 6-#5 Bars, 5' Length 11-1/2" Bolt Circle Dia. 10' Ground Rod (5/8") 3" PVC Rigid Raceway 1x36x4 Anchor Bolts 2' 6' Min. NOTES: Foundation is to be level and broom finished with a 1" chamfer. Anchor bolts shall project 2.75" above the finished foundation. No shimming, double nutting or other form of adjustment to level the pole will be allowed. Depth of foundation will depend on soil conditions. A minimum depth of 6' is required. RESIDENTIAL STREET LIGHT FOUNDATION Concrete Foundation.dwg STREET & PAVEMENT Public Works & 10/10/2007 DRAWING NO. STR-06-F

16 SAME AS MANHOLE 5" 4' MASTIC JOINT BRICK DAM SET IN MORTAR EXISTING MANHOLE INVERT OF DROP SEWER PIPE TO BE AT SAME ELEV. AS EXISTING BENCH POURED CONCRETE DUCTILE IRON PIPE PRECAST MONOLITHIC CONCRETE BASE SEWER MAIN 3/4" STONE DROP FOR EXISTING MANHOLE DROPMANH.DWG SANITARY SEWER DRAWING NO. SS-03

17 SAME AS MANHOLE 5" 4' Min. MASTIC JOINT BRICK DAM SET IN MORTAR. 1 Dam Height = 2 pipe dia. PRECAST MONOLITHIC DROP CONNECTION SAME SIZE AS INCOMING SEWER (8" MIN, 12" MAX) LC OF DROP SEWER AT SAME ELEV. AS SPRING LINE OF MAIN SEWER 8" DUCTILE IRON PIPE PRECAST MONOLITHIC CONCRETE BASE SEWER MAIN 3/4" STONE DROP MANHOLE DROPMH.DWG SANITARY SEWER DRAWING NO. SS-02

18 KJT Wall End connection to fit pipe used. WALL PIPE DIA. 12" 15" 18" 21" WALL 2" 2 1/4" 2 1/2" 2 3/4" A 4" 9" 9" B 2'-0" 2'-3" 2'-3" 2'-11" C 4'-7/8" 3'-10" 3'-10" 3'-2" D 6'-7/8" 6'-1" 6'-1" 6'-1" E 2'-0" 2'- 3'-0" 3'- R 9" 11" 12" 13" SLOPE 3:1 3:1 3:1 3:1 Pipe diameter A R LC A E 24" 27" 30" 33" 3 3" 3 1/4" 3 1/2" 3 3/4" 4" 9 1/2" 10 1/2" 1'-0" 1'-1 1/2" 1'-3" 3'-7 1/2" 4'-0" 4'- 4'-10 1'2" 5'-3" 2'- 2'-1 1/2" 1'-7 3/4" 3'-3 1/4" 2'-10 3/4" 6'-1 1/2" 6'-1 1/2" 6'-1 3/4" 8'-1 3/4" 8'-1 3/4" 4'-0" 14" 3:1 4'- 14 1/2" 3:1 5'-0" 15" 3:1 5'- 17 1/2" 3:1 6'-0" 20" 3:1 42" 4 1/2" 1'-9" 5'-3" 2'-11" 8'-2" 6'- 22" 3:1 Wall 48" 54" 5" 5 1/2" 2'-0" 2'-3" 6'-0" 5'-5" 2'-2" 2'-11" 8'-2" 8'-4" 7'-0" 7'- 22" 24" 3:1 2.4:1 D Wall C B SLOPE X TO Y X Wall Pipe diameter Standard reinforcement for circular Class III, Wall B reinforced concrete pipe. Same reinforcement as inner cage. 1/2 wall Y 2 - #4 Bars 3" 8" 3" A 12" End block cast seperate. Cast incidental to end section 1-1 1/2" R Pipe diameter E Wall PRECAST CONCRETE FLARED END SECTIONS SHALL CONFORM TO THE APPLICABLE REQUIREMENTS OF A.A.S.H.O. M-170 CLASS III, WALL B REINFORCED CONCRETE PIPE. PRECAST CONCRETE FLARED END SECTION FOR PIPE DIAMETER REQUIRED SHALL BE AS INDICATED ON DETAIL PLAN FOR EACH INDIVIDUAL INSTALLATION. FLARED END SECTIONS 12 INCHES OR GREATER WILL REQUIRE GRATES. FLRDEND.DWG PRECAST REINFORCED CONCRETE FLARED END SECTION STORM SEWER DRAWING NO. STS-08

19

20 CASTING AS SPECIFIED MASTIC 7" MIN. 24" MAX. PRECAST CONC. 2 ADJUSTING RINGS 48" DIAMETER 60" DIAMETER PRECAST REINF. CONCRETE SEE I.D.O.T. STD NOTES: 1. Adjustment: Any structure located within pavement shall require the use of at least one (1) rubber adjustment riser, Infra-Riser brand or approved equal, and, if necessary, said riser shall be of the tapered type in order to match the proposed grade of the roadway. No more than two (2) precast concrete adjusting rings with six (6) inch maximum height adjustment shall be allowed. Adjustments within pavement that are less than three (3) inches in height shall consist of only rubber adjustment riser(s). The minimum thickness of a rubber adjustment riser shall be one (1) inch. Adjustments within pavement greater than three (3) inches in height shall use a minimum three (3) inch precast concrete riser for the lower riser, and the final riser shall be of the rubber type. 2. Sealing: All non-rubber mating surfaces, exterior joints of frames, adjustment riser(s), flat slab top or cone section (if applicable) and structure section shall be sealed with a uniform application of bituminous mastic sealant. The mating surfaces of all rubber adjustment risers shall be sealed with the manufacturer's recommended sealant for rubber adjustment risers. If multiple adjustment risers are required, a continuous application of sealant shall be applied between each unit. Interior surfaces shall be sealed with concrete mortar or epoxy mortar. Concrete mortar or epoxy mortar will not be used on mating surfaces as a sealant between adjustment risers, structure sections or frames. FLAT SLAB TOP FLTSLAB.DWG STORM SEWER DRAWING NO. STS-06

21 22 3/4" DIA. A A B VIL LA G E OF B 23" 3/4" STORM SEWER 3/4" MIN. FOR C.I. 2" RAISED LETTERS ORL AND PA R K SMALL PICK OPENING 2 DIA. 23" DIA. 1 1/2" 21" DIA. 1" 3 1/2" 1 3/4" 1 3/4" 3 1/2" 1 1/4" 1 1/4" 9" 5/8" 5/8" 2 1/2" 1" DIA. 24" DIA. 3 DIA. SECTION B-B CAST CLOSED LID SECTION A-A CAST FRAME NOTES: 1. DUCTILE IRON CASTINGS SHALL BE GRADE AND SHALL BE TESTED IN ACCORDANCE WITH FEDERAL SPECIFICATIONS. 2. ALL LIDS AND COVERS SHALL BE MACHINED. 3. THE MANHOLE COVERS SHALL HAVE RAISED LETTERS AS SHOWN. 4. ALTERNATIVE TO DUCTILE IRON LID, GRAY IRON LID MAY BE USED. 5. MINIMUM WEIGHTS FOR CASTINGS AS SHOWN. 6. CASTINGS SHALL BE EAST JORDAN IRON WORKS 1050Z1 FRAME AND 1020A COVER. FRAME&CO.DWG DRAWN BY: STORM SEWER FRAME & COVER STORM SEWER DRAWING NO. STS-14

22 CASTING AS SPECIFIED MASTIC MAX. PRECAST CONC. 2 ADJUSTING RINGS 3" 24" DIA. 1 MIN. MORTAR RUBBER BOOT PER ASTM C-923 4" POURED CONCRETE FILLET IN INLET BOTTOM 3/4" STONE PRECAST REINFORCED CONCRETE INLET BOTTOM WITH INTEGRAL SIDEWALL NOTES: 1. Adjustment: Any structure located within pavement shall require the use of at least one (1) rubber adjustment riser, Infra-Riser brand or approved equal, and, if necessary, said riser shall be of the tapered type in order to match the proposed grade of the roadway. No more than two (2) precast concrete adjusting rings with six (6) inch maximum height adjustment shall be allowed. Adjustments within pavement that are less than three (3) inches in height shall consist of only rubber adjustment riser(s). The minimum thickness of a rubber adjustment riser shall be one (1) inch. Adjustments within pavement greater than three (3) inches in height shall use a minimum three (3) inch precast concrete riser for the lower riser, and the final riser shall be of the rubber type. 2. Pipe and frame seals: All pipe connection openings shall be precast with resilient rubber water tight pipe to manhole sleeves or seals conforming to ASTM C-923. Adapter chimney seal with twelve (12) inch sleeve type shall extend from the manhole cone to the manhole frame for all structures in the right-of-way. 3. Sealing: All non-rubber mating surfaces, exterior joints of frames, adjustment riser(s), flat slab top or cone section (if applicable) and structure section shall be sealed with a uniform application of bituminous mastic sealant. The mating surfaces of all rubber Adjustment risers shall be sealed with the manufacturer's recommended sealant for rubber adjustment risers. If multiple adjustment risers are required, a continuous application of sealant shall be applied between each unit. Interior surfaces shall be sealed with concrete mortar or epoxy mortar. Concrete mortar or epoxy mortar will not be used on mating surfaces as a sealant between adjustment risers, structure sections or frames 4. All bottom sections shall be monolithically precast including bases and invert flowlines. 5. Provide CA-6 aggregate backfill around inlet to subgrade elevation in paved areas.for subgrade. INLET TYPE A INLET_A.DWG DRAWN BY: Village of STORM SEWER DRAWING NO. STS-05

23 RESIDENTIAL STREET LIGHT ELECTRICAL SUPPLY CONNECTION Bussman identified solid neutral fuse holder with crimp terminals and Cooper-Bussman rubber boots, (IA0512). Bussman in line link with crimp terminals and Cooper-Bussman rubber boots, (IA0512) on hot lead. DISCONNECT PEDESTAL API 10x14 ELECTRIC COMED SERVICE PEDESTAL 1' LEAVE 8' OF CABLE COILED 2'- 1-1/2" UNIT DUCT 2" PVC Sch. 40 PEDESTAL LEAVE SUFFICIENT CABLE FOR CONNECTION TO C.E. COMPANY C.E. POLE DISCONNECT PEDESTAL API 10x14 Bussman identified solid neutral fuse holder with crimp terminals and Cooper-Bussman rubber boots, (2A0660 or 2A0661). Bussman in line link with crimp terminals and Cooper-Bussman rubber boots, (2A0660 or 2A0661) on hot lead. ELECTRIC 3' 10' 2'- 1-1/2" UNIT DUCT POWER POLE RESIDENTIAL STREET LIGHT CONNECTION Lite_Connection.DWG Engineering STREET & PAVEMENT Department DRAWING NO. STR-07

24 RESIDENTIAL STREET LIGHT ROUND TAPERED ALUMINUM SINGLE TRUSS ARM-CLAMP ON MOUNTING ARM LUMINAIRE WATTAGE VOLTAGE HEIGHT LOCATION LENGTH LENS TYPE 250 w 120 volt 30' Major Intersections 12'-15' Cobra Head w/county & State (drop bowl) roadways. 150 w 120 volt 30' All local roadway 12' Sharp Cutoff intersection in (flat lens) Subdivisions. 150 w 120 volt 30' Curves of Street 12' Sharp Cutoff (flat lens) 150 w 120 volt 30' Mid-block 12' Sharp Cutoff (flat lens) Pole Cap with S.S. Screws 4 1/2" Wire Hole in Shaft with 1" I.D. Rubber Grommet Tapered Truss Bracket Alum. Alloy 6063-T6 2" NPS Slipfitter Tapered Alum. Tube 8" Butt Dia., 4-1/2" Top Dia Wall Alloy 6063-T6 Satin Ground Finish 30' MOUNTING HEIGHT Extruded 4"x8" Reinforced Handhole with Ground Lug attached to frame 1" Chamfer 8" 2' 1'- 4" Splices within the handhole shall be as follows: Bussman identified solid neutral fuse holder with crimp terminals and Cooper-Bussman rubber boots, (2A0660 or 2A0661). Bussman in line link with crimp terminals and Cooper-Bussman rubber boots, (2A0660 or 2A0661) on hot lead. 3" PVC Rigid Raceway 1x36x4 Anchor Bolts 6' Fdn. Cage #3 12" O.C., 1 Dia. Attached to 6-#5 Bars, 5' Length 10' Ground Rod (5/8") 11-1/2" Bolt Circle Dia. 3" PVC Rigid Raceway 1x36x4 Anchor Bolts 2' Lite_Std_30.dwg DRAWN BY: TYPICAL RESIDENTIAL STREET LIGHT STREET & PAVEMENT DRAWING NO. 08/17/2006 STR-06

25 22 3/4" DIA. V I L L AGE OF A 23" DIA. 3/4" A B SANITARY B 3/4" MIN. FOR C.I. 2" RAISED LETTERS OR L AND PAR K SMALL PICK OPENING 2 DIA. 1 3/4" 3 1/2" 1 1/2" 1" 3 1/2" 1 1/4" 2 1/2" 1 1/4" 1" 9" 1 3/4" 23" DIA. 21" DIA. 5/8" DIA. 5/8" 24" DIA. 3 DIA. SECTION A-A CAST FRAME SECTION B-B CAST CLOSED LID WT. = 330 LBS. 1. DUCTILE IRON CASTINGS SHALL BE GRADE & SHALL BE TESTED IN ACCORDANCE WITH FEDERAL SPECIFICATIONS. 2. CASTINGS SHALL BE EAST JORDAN IRON WORKS 1050Z1 FRAME AND 1020A COVER. SANITARY MANHOLE FRAME & COVER MANHLFRM.DWG SANITARY SEWER DRAWING NO. SS-04

26

27 CATCH BASIN TRAPS R-3700 to R-3708 Series Cast iron catch basin traps are used extensively on sewer catch basins or manholes to prevent clogging on sanitary systems. They provide a waterseal against escaping gases. Traps with drop type catch basins provide effective means of keeping pipe lines entirely clean. The drop portion of inlet retains all solid material and the trap prevents all floating debris from entering outlet pipe. All catch basin traps shown are of approved design. R-3700 Pipe size to 12. Setting method 4 anchor bolts. R-3701 Series Dimensions in Inches Catalog For Pipe Setting No. A B Size Method Notes R to 6 on 2 hooks R on 2 hooks Cast Iron Handle. R on 2 hooks R on 2 hooks Bottom of trap 6 min. R on 2 hooks below flow line. R on 2 hooks 229

28 R-3711 Catch Basin Hood with Hook for 12 Wall R-3712 Catch Basin Trap BRASS WEDGE #35 BRASS SASH CHAIN NEENAH FOUNDRY CO. 9" 22 3/4" 30" 39 1/4" 33 1/4" 3" 15" ; ; ; ;; ; ; 1/8" THICK NEOPRENE GASKET ;; ;; ; ; 9" 15" ;;;; ;; ; ; ; ; ; ; ;;; ; 9" 5/8" Typ. 234

29 P.C.C. CURB DRAINAGE VOID SURFACE WATER FLOW ECOSTONE PAVERS SOIL CHIP GRAVEL (CA-16, 1.5 to 2 inch) PERMEABLE BASE (CA-7, 6 inches after roller compaction) (CA-1, 9 inches after roller compaction) GEOTEXTILE FILTER LOW PERMEABILITY SUBGRADE PERFORATED PVC W/ FABRIC SOCK TO DAYLIGHT HIGH WATER TABLE PAVER DETAIL Cross Section

30 4:1 15' Maintenance Path 15:1 4:1 4:1 HWL Native Natural Plantings 10:1 OPTIONAL SAFETY SHELF NWL 2' 2:1 2:1 Min. 15' Basin Bottom Wet Basin Cross Section FILE NAME: Storm Sewer Improvement DRAWING NO. STS-13

31 STANDARD FRAME AND LID PER VILLAGE STANDARDS GRADE 3/4" MASTIC 2' PRECAST ADJUSTING RINGS ( MAX., 2 RINGS MAX.) 5' MINIMUM STEPS 12" ON CENTER MASTIC JOINT PRECAST VALVE VAULT Min. 5' CAST IRON TAPPING SLEEVE EXIST. WM VARIES GROUT CONCRETE BLOCK SUPPORTS CENTERED UNDER VALVE AND EXISTING WATER MAIN PRECAST CONCRETE BASE 4" STONE CUSHION PRESSURE CONNECTION PRESSURE.DWG WATER MAIN DRAWING NO. 2/24/05 WM-05

32 2' 2'.5" 1.5" 2.5" 1.5" A A 11.5" 1"R 3/8" CHECKERED THREADS RUBBER BOOT PER ASTM C-923.5" 5" Catch Basin Hood FLOW VARIABLE 1.5" 1".5".75" 2" 3/8" PREFABRICATED CONCRETE SLAB PLAN-ECCENTRIC SECTION A-A CAST IRON STEPS 2' C NOTES: DIMENSION "C" FOR PRECAST REINFORCED CONCRETE SECTIONS MAY VARY FROM THE DIMENSION GIVEN TO PLUS 6 INCHES. T D CIRCULAR T VARIABLE THE CAST IRON STEPS AS DETAILED HERE ON ARE TYPICAL. STEPS OF OTHER DESIGN AND MATERIAL THAT WILL CONFORM TO THE MINIMUM REQUIREMENTS OF THE STEPS SHOWN, MAY BE USED WHEN APPROVED BY THE ENGINEER. d CAST IRON STEPS SHALL BE GRAY IRON CONFORMING TO THE REQUIREMENTS OF ART OF THE STANDARD SPECIFICATIONS. d STEPS SHALL BE EMBEDDED INTO THE WALL A MINIMUM OF 3 INCHES. STEPS SHALL NOT BE EXTENDED ON THE OUTSIDE. PREFABRICATED CONCRETE SLAB 2.5' min. PRECAST REINFORCED CONCRETE SECTIONS D C T(MIN) 5' 3'-9" 5" 3" 3/4" STONE PLAN-CONCENTRIC RESTRCTR.DWG OUTLET CONTROL STRUCTURE STORM SEWER DRAWING NO. STS-15

33 SANTRENCH.DWG DRAWING NO. SS-06 FINISHED GRADE BACKFILL WITH EXCAVATED MATERIAL EXCEPT WHERE GRANULAR MATERIAL IS REQUIRED. VARIES ACTUAL TRENCH WALL ANGLE OF REPOSE AS CALCULATED BY OSHA FOR SLOPING EXCAVATIONS IN VARIOUS TYPES OF SOIL (AVG. SOIL = 1:1 SLOPE) NOTE THAT PORTABLE TRENCH BOXES OR SLIDING TRENCH SHIELDS MAY BE USED IN LIEU OF SLOPING. 5' MAX. 4" MIN. MIN. GRANULAR COVER - TRENCH > 10'. WHEN REQUIRED EXTEND TO SUBGRADE ELEVATION IN PAVED AREAS 1/4" - 1" STONE IF ENCOUNTERED, REMOVE UNSUITABLE MATERIAL AND REPLACE WITH SUITABLE MATERIAL AS DIRECTED BY THE ENGINEER. TRENCH WIDTH SHALL BE THE MINIMUM REQUIRED IN ORDER TO COMPLY WITH OSHA SAFETY STANDARDS. ABS AND PVC WHEN USED AS SANITARY SEWER SHALL REQUIRE GRANULAR BEDDING AND COVER AS DETAILED. DIP WHEN USED AS SANITARY SEWER SHALL REQUIRE GRANULAR TO TOP OF PIPE. TRENCH SECTION SANITARY SEWER SANITARY SEWER

34 CA-11 STONE 12" 4" MIN. MIN. 12" MIN. 12" MIN. PVC TEE, SDR 26 10' MAX. TO FINISH GROUND SURFACE (8' MINIMUM) CA-11 STONE PVC SDR 1% MIN. SLOPE MIN. 45Ā BEND, PVC SDR MAXIMUM SLOPE UNDISTURBED EARTH-SHAPED TO PROVIDE UNIFORM BEARING FOR 1/4 OF BARREL CIRCUMFERENCE VERTICAL RISER ADAPTER PVC TEE, SDR IF Ф < 45º AND DEPTH IS LESS THAN 20', USE PVC TEE, PVC VERTICAL RISER ADAPTER, PVC RISER PIPE & PVC TOP ELBOW. 2. ALL PVC PIPE LESS THAN 14" DIA. WITH A DEPTH LESS THAN 20', SHALL BE ASTM D3034, SDR 26, WITH ELASTOMERIC GASKET TYPE JOINTS COMPLYING WITH ASTM F477 AND ASTM D ALL PVC PIPE 14" AND GREATER WITH A DEPTH LESS THAN 20', SHALL BE ASTM F679, PS115, WITH ELASTOMERIC GASKET TYPE JOINTS COMPLYING WITH ASTM F477 AND ASTM D A MINIMUM DISTANCE OF 3 FEET IS REQUIRED BETWEEN 45º BENDS. 5. TRENCH BACKFILL SHALL BE INSTALLED PER THE SANITARY SEWER TRENCH DETAIL. Serv_Riser_5-20ft.dwg SANITARY SERVICE RISER < 20' Deep SANITARY SEWER 11/18/09 DRAWING NO. SS-05

35 3/4" STONE 12" 4" MIN. MIN. 12" MIN. 12" MIN. 10' MAX. TO FINISH GROUND SURFACE (8' MINIMUM) CA-10 STONE PVC SDR 1% MIN. SLOPE MIN. 45Ā BEND 1 1 MAXIMUM SLOPE UNDISTURBED EARTH-SHAPED TO PROVIDE UNIFORM BEARING FOR 1/4 OF BARREL CIRCUMFERENCE DIA. SERVICE RISER W/ VERTICAL RISER ADAPTER PVC TEE, SDR IF Ф < 45º USE PVC PUSH-ON JOINT WYE, PVC ELBOW, PVC RISER PIPE & PVC TOP ELBOW. 2. IF Ф > 45º USE DUCTILE IRON M.J. TEE WITH PVC / DUCTILE TRANSITION GASKET, DUCTILE IRON RISER PIPE AND DUCTILE IRON TOP ELBOW COATED WITH PROTECTO 401 OR APPROVED EQUAL. 3. ALL PVC PIPE AND FITTINGS SHALL BE ASTM D3034, SDR 26, WITH ELASTOMERIC GASKET TYPE JOINTS COMPLYING WITH ASTM F477 AND ASTM D A MINIMUM DISTANCE OF 3 FEET IS REQUIRED BETWEEN 45º BENDS. 5. TRENCH BACKFILL SHALL BE INSTALLED PER THE SANITARY SEWER TRENCH DETAIL. SERVRSR.DWG SANITARY SERVICE RISER SANITARY SEWER DRAWING NO. SS-05

36 CA-11 STONE 4" 12" MIN. MIN. 12" MIN. 12" MIN. DUCTILE IRON TEE (M. J.) 10' MAX. TO FINISH GROUND SURFACE (8' MINIMUM) CA-11 STONE PVC SDR 1% MIN. SLOPE MIN. TRANSITION GASKET 45 BEND, DUCTILE IRON (M. J.) 1 1 MAXIMUM SLOPE DUCTILE IRON RISER UNDISTURBED EARTH-SHAPED TO PROVIDE UNIFORM BEARING FOR 1/4 OF BARREL CIRCUMFERENCE DUCTILE IRON TEE (M. J.) 1. IF Ф < 45º AND DEPTH IS GREATER THAN 20', USE DUCTILE IRON SEWER SAFE TEE, DUCTILE IRON SEWER SAFE RISER PIPE, DUCTILE IRON SEWER SAFE ELBOW WITH TRANSITION GASKET TO PVC. 2. ALL PVCO (POLYVINYL CHLORIDE MOLECULARLY ORIENTATED) PIPE LESS THAN 14" DIA. WITH A DEPTH GREATER THAN 20', SHALL CONFORM TO ASTM F1483, AWWA C909 CLASS 150, WITH ELASTOMERIC GASKET TYPE JOINTS COMPLYING WITH ASTM F477 AND ASTM D ALL PVC PIPE 14'" AND GREATER WITH A DEPTH GREATER THAN 20',SHALL CONFORM TO AWWA C905, DR 25, WITH ELASTOMERIC GASKET TYPE JOINTS COMPLYING WITH ASTM F477 AND ASTM D A MINIMUM DISTANCE OF 3 FEET IS REQUIRED BETWEEN 45º BENDS. 5. TRENCH BACKFILL SHALL BE INSTALLED PER THE SANITARY SEWER TRENCH DETAIL. 6. THE DUCTILE IRON SEWER SAFE PIPE SHALL HAVE MECHANICAL JOINTS. Serv_Riser_20ft.dwg SANITARY SERVICE RISER 20' AND GREATER DEPTH SANITARY SEWER 11/18/09

37 VARIABLE 5".5" 1.5" 2.5" A INSIDE FACE OF STRUCTURE 1" R A CHECKERED TREAD 12.5" 1.5" 3/8" 1.5".5" 1.5".5" 1".75".5" 2" 3/8" SECTION A-A CAST IRON STEPS NOTES: 1. STEPS SHALL BE EMBEDDED INTO THE WALL A MINIMUM OF 3 INCHES. STEPS SHALL NOT BE EXTENDED ON THE OUTSIDE. 2. CAST IRON STEPS SHALL BE GRAY IRON CONFORMING TO THE REQUIREMENTS OF ARTICLE OF THE STANDARD SPECS. 3. STEEL REINFORCED PLASTIC. MANHOLE STEPS SHALL BE MADE WITH AN APPROVED PLASTIC SUCH AS COPOLYMER POLYPROPYLENE MEETING WITH THE REQUIREMENTS OF ASTM DESIGNATION 2146 TYPE II GRADE 49108, RE- INFORCED WITH A DEFORMED 3/8 INCH DIAMETER REIN- FORCING BAR WHICH CONFORMS TO THE REQUIREMENTS OF ASTM DESIGNATION A-615 GRADE 60. STEPDETA.DWG CATCH BASIN-TYPE A STEP DETAIL STORM SEWER DRAWING NO. STS-03

38 CASTING AS SPECIFIED MASTIC 24" MAX. PRECAST CONC. 2 ADJUSTING RINGS FLAT SLAB TOP MAY BE SUBSTITUTED 1 O.C. 2' - ECCENTRIC 3' - 9" CONE SECTION 5" 48" DIAMETER 60" DIAMETER ONE PIPE LENGTH MORTAR RUBBER BOOT PER ASTM C-923 VARIABLE PRECAST REINFORCED CONCRETE SECTION MIN. POURED CONCRETE FILLET IN INLET BOTTOM 3/4" LIMESTONE (NO FINES) PRECAST REINFORCED CONCRETE INLET BOTTOM WITH INTEGRAL SIDEWALL NOTES: 1. Adjustment: Any structure located within pavement shall require the use of at least one (1) rubber adjustment riser, Infra-Riser brand or approved equal, and, if necessary, said riser shall be of the tapered type in order to match the proposed grade of the roadway. No more than two (2) precast concrete adjusting rings with six (6) inch maximum height adjustment shall be allowed. Adjustments within pavement that are less than three (3) inches in height shall consist of only rubber adjustment riser(s). The minimum thickness of a rubber adjustment riser shall be one (1) inch. Adjustments within pavement greater than three (3) inches in height shall use a minimum three (3) inch precast concrete riser for the lower riser, and the final riser shall be of the rubber type. 2. Pipe and frame seals: All pipe connection openings shall be precast with resilient rubber water tight pipe to manhole sleeves or seals conforming to ASTM C-923. Adapter chimney seal with twelve (12) inch sleeve type shall extend from the manhole cone to the manhole frame for all structures in the right-of-way. 3. Sealing: All mating surfaces of adjustment riser(s), structure sections, and frames shall be sealed with a mastic sealant. No concrete mortar or epoxy shall be allowed as a sealant for adjustment risers, structure sections or frames. If multiple adjustment risers are required, a continuous application of sealant shall be applied between each unit. 4. All bottom sections shall be monolithically precast including bases and invert flowlines. 5. Provide CA-6 aggregate backfill around manhole to subgrade elevation in paved areas.for subgrade. STORM MANHOLE STORMMH.DWG STORM SEWER DRAWING NO. STS-01

39 FINISHED GRADE BACK FILL WITH EXCAVATED MATERIAL EXCEPT WHERE GRANULAR MATERIAL IS REQUIRED. VARIES ACTUAL TRENCH WALL ANGLE OF REPOSE AS CALCULATED BY O S H A FOR SLOPING EXCAVATIONS IN VARIOUS TYPES OF SOIL (AVG. SOIL= 1:1 SLOPE). NOTE THAT PORTABLE TRENCH BOXES OR SLIDING TRENCH SHIELDS MAY BE USED IN LIEU OF SLOPING. 5' MAX. MIN. GRANULAR COVER. WHEN REQ'D. EXTEND TO SUB GRADE ELEVATION IN PAVED AREAS. 4" MIN. IF ENCOUNTERED, REMOVE UNSUITABLE MATERIAL AND REPLACE WITH SUITABLE MATERIAL, AS DIRECTED BY THE ENGINEER. 3/4" STONE TRENCH WIDTH SHALL BE THE MINIMUM REQUIRED IN ORDER TO COMPLY WITH O S H A SAFETY STANDARDS. STORMTRE.DWG DRAWN BY: Village of TRENCH SECTION (STORM SEWER) STORM SEWER DRAWING NO. STS-11

40 3" FREEFALL SUMP PUMP OUTLET * NOTE # 1 FINISHED GRADE CONNECT 4" PLASTIC PIPE TO INLET OR STORM SEWER PIPE LOCATED ON LOT STORM SEWER 3 BUILDING WALL * NOTE # 2 MINIMUM DEPTH WILL BE 3 UNLESS APPROVED BY VILLAGE ENGINEERING DEPARTMENT. * SUBJECT TO APPROVALS & MODIFICATIONS 4" PLASTIC PIPE MIN. 0.5 % SLOPE SUMP PUMP DRAIN SUMPDRN.DWG STORM SEWER DRAWING NO. STS-12

41 A A UNDISTURBED SOIL L UNDISTURBED SOIL L 1' - MIN 1' - MIN PLAN A PLAN A A UNDISTURBED SOIL L 1' - MIN 4" MIN H MIN 4" MIN PLAN A SECTION A CONCRETE THRUST BLOCK DIMENSIONS PIPE SIZE BEND BEND 45 -BEND 90 -BEND TEE & PLUG DIAMETER H L < 8" 1'- 1'- < 12" 1'- 2'-0" < 1 2'-0" 2'-0" H 2'-0" 2'-3" 2'- L H L H L H L 2'- 2'- 3'-0" 3'- 4'-0" 3'-0" 3'- 2'- 3'-0" 3'- 4'-0" 4'- 3'- 4'-0" 3'-0" 4'-0" 4'- 5'-0" 6'-0" 4'- 5'- 1. ALL BLOCKING SHALL BE CONSTRUCTED WITH POURED CL. X CONCRETE AGAINST UNDISTURBED VERTICAL EARTH FACE WITH A MINIMUM WIDTH OF 12 INCHES. 2. THRUST BLOCKS TO BE USED AT ALL BENDS 11 1/4 DEGREES OR GREATER. 3. MECHANICAL JOINT RETAINER GLANDS MAY BE USED AS AN ALTERNATIVE TO CONCRETE THRUST BLOCK INSTALLATION WHEN APPROVED BY THE VILLAGE ENGINEER. 4. TEST PRESSURE 150 PSI. TB2.DWG CONCRETE THRUST BLOCK DETAILS WATER MAIN DRAWING NO. WM-10

42 SOD PLUGS OR GRASS SEED TURFSTONE PAVER COMPACTED SOIL AT PERIMETER TOPSOIL IN OPENINGS BEDDING SAND (1", 25mm) AGGREGATE BASE (As Specified By a Professional Engineer) GEOTEXTILE (Where Specified) SUBGRADE SCALE Inches 0 6 mm FIRE ACCESS ROAD Turfstone Paver Designed to be a step ahead R PAVER DETAIL Cross Section Engineer's Seal This cross section is intended for preliminary design purposes only. A qualified professional Engineer should approve the final design and confirm site conditions UNILOCK FIREROAD.DWG

43 A A 2.5" 2" 1.5" 33" DIA. 1" 1.5" 1" 3" 1" 23" DIA. SECTION A-A CAST GRATE WT. 200 LBS. THE CAST GRATE MAY BE EITHER GRAY IRON OR DUCTILE IRON CONFORMING TO THE STANDARD SPECIFICATIONS. DUCTILE IRON CASTING SHALL BE GRADE GRATE TYPE 8 GRATE-8.DWG STORM SEWER DRAWING NO. STS-07

44 EJIW Frame 7525 Catch Basin Rubber Boot Curb and Gutter ±25' PVC Pipe Underdrain Curb and Gutter Asphalt Pavement PLAN SCALE: VIEW N.T.S. Curb and Gutter Asphalt Pavement 3" PVC Pipe Underdrain 1'- Min. 3" Underdrain Aggregate (Washed CA-7) Class I Geotextile 3" 3" PIPE UNDERDRAIN BEHIND CURB SCALE: N.T.S. Underdrain Notes: 1. The installation of the underdrains shall conform to section of the Illinois Department of Transportaion Standard pecifications for Road and Bridge Construction. 2. Pipe material shall be perforated PVC, per article of the IDOT Standard Specifications. 3. The underdrains shall be installed with the drain perforations down. All underdrains shall be held in the center of the trench by mechanical means while placing compacted trench backfill of washed CA After the underdrain pipe is installed, the geotextile shall be folded over the underdrain aggregate and overlapped a minimum of 12". 5. The underdrains shall have watertight joints, and be tied into the nearest storm sewer inlet. The connection to the inlet structure shall conform to ASTM C-923. CURB UNDERDRAIN DETAIL - Back of Curb Underdrain-bc.dwg DRAWN BY: STREET & PAVEMENT Public Works Department rjr DRAWING NO. 11/20/2006 STR-20

45 EJIW Frame 7525 Catch Basin Rubber Boot Asphalt Pavement Curb and Gutter 25' PVC PIPE UNDERDRAIN PLAN VIEW SCALE: N.T.S. Curb and Gutter Asphalt Pavement 3" PVC Pipe Underdrain 1'- Min. 3" Underdrain Aggregate (Washed CA-7) Class I Geotextile 3" 3" PIPE UNDERDRAIN FRONT OF CURB SCALE: N.T.S. Underdrain Notes: 1. The installation of the underdrains shall conform to section of the Illinois Department of Transportaion Standard pecifications for Road and Bridge Construction. 2. Pipe material shall be perforated PVC, per article of the IDOT Standard Specifications. 3. The underdrains shall be installed just below the bottom of the existing curb (or as necessary to provide positive flow), with the drain perforations down. All underdrains shall be held in the center of the trench by mechanical means while placing compacted trench backfill of washed CA After the underdrain pipe is installed, the geotextile shall be folded over the underdrain aggregate and overlapped a minimum of 12". 5. The underdrains shall have watertight joints, and be tied into the nearest storm sewer inlet, as designated by the Village. CURB UNDERDRAIN DETAIL - Front of Curb Underdrain-fc.dwg DRAWN BY: STREET & PAVEMENT Public Works Department rjr DRAWING NO. 11/15/2006 STR-

46 STANDARD FRAME AND LID PER VILLAGE STANDARDS CONCRETE ADJUSTMENT RINGS AS REQUIRED ( MAX., 2 RINGS MAX.) 3/4" MASTIC PRECAST REINFORCED CONCRETE CONE. 2' 5' MIN. COVER MASTIC JOINT 5' DIA. (FOR VALVES TO 12") 8" MIN. PRECAST REINFORCED CONCRETE BASE SLAB ON A 3/4" STONE CUSHION (4" MIN.) BRICK OR CONCRETE BLOCK SUPPORTS Notes: 1. Adjustments to existing structures should not exceed a total of 12" of adjustment rings. Any adjustment greater than 12" must use a barrel extention. 2. Precast concrete sections shall conform to ASTM C478. VALVEVAU.DWG VALVE VAULT WATER MAIN DRAWING NO. 11/19/07 WM-01

47 STANDARD FRAME AND LID PER VILLAGE STANDARDS CONCRETE ADJUSTMENT RINGS AS REQUIRED ( MAX., 2 RINGS MAX.) 3/4" MASTIC PRECAST REINFORCED CONCRETE CONE 2' STANDARD STEPS 12" ON CENTER MASTIC JOINT 5' DIA. (FOR VALVES TO 12") 8" MIN. BRICK OR CONCRETE BLOCK SUPPORTS PRECAST REINFORCED CONCRETE BASE SLAB ON A 3/4" STONE CUSHION (4" MIN.) PRECAST SECTIONS SHALL CONFORM WITH ASTM C478 VALVEVA1.DWG Village of VALVE VAULT OFFSET CONE WATER MAIN DRAWING NO. 2/24/05 WM-02

48 22 3/4" DIA. V I L L AGE OF A 23" DIA. 3/4" A B WATER B 3/4" MIN. FOR C.I. 2" RAISED LETTERS O RL A ND PARK SMALL PICK OPENING 2 DIA. 3 1/2" 1 3/4" 23" DIA. 21" DIA. 1 1/2" 1" 5/8" DIA. 5/8" 3 1/2" 1 1/4" 1 1/4" 1" 9" 1 3/4" 2 1/2" 24" DIA. 3 DIA. SECTION A-A CAST FRAME SECTION B-B CAST CLOSED LID WT. = 330 LBS. 1. DUCTILE IRON CASTINGS SHALL BE GRADE & SHALL BE TESTED IN ACCORDANCE WITH FEDERAL SPECIFICATIONS. 2. ALL LIDS AND COVERS SHALL BE MACHINED 3. THE MANHOLE COVERS SHALL HAVE RAISED LETTERS AS SHOWN. 4. ALTERNATIVE TO DUCTILE IRON LID, GRAY IRON LID MAY BE USED 5. MINIMUM WEIGHTS FOR CASTINGS AS SHOWN 6. CASTINGS SHALL BE EAST JORDAN IRON WORKS 1050Z1 FRAME & 1020A COVER. Village of VALVE VAULT FRAME & COVER VALVFRM.DWG WATER MAIN DRAWING NO. WM-03

49 FINISHED GRADE 8'-0" 5'- MINIMUM COVER CORPORATION STOP MUELLER H WATER SERVICE LINE 1-1 2" TYPE 'K' COPPER LOT LINE SERVICE BOX MUELLER MINNEAPOLIS PATTERN H /2" - 3/4" STONE CURB STOP : MUELLER H PLACE ON UNDISTURBED GROUND OR BACKFILL W/ 1/2" - 3/4" STONE NOTE : SOLID CONCRETE SUPPORT BLOCK TERMINATE WATER SERVICE AT CURB STOP UNLESS OTHERWISE SHOWN ON THE PLAN. WATER SERVICE CONNECTION Water_Service.dwg DRAWN BY: WATER MAIN 4/28/05 wdc DRAWING NO. WM-08

50 FINISHED GRADE BACKFILL WITH EXCAVATED MATERIAL EXCEPT WHERE GRANULAR MATERIAL IS REQUIRED. VARIES ACTUAL TRENCH WALL ANGLE OF REPOSE AS CALCULATED BY OSHA FOR SLOPING EXCAVATIONS IN VARIOUS TYPES OF SOIL (AVG. SOIL = 1:1 SLOPE) NOTE THAT PORTABLE TRENCH BOXES OR SLIDING TRENCH SHIELDS MAY BE USED IN LIEU OF SLOPING. 5' MAX. 4" MIN. MIN. GRANULAR COVER WHEN REQUIRED EXTEND TO SUBGRADE ELEVATION IN PAVED AREAS 1/4" - 1" STONE IF ENCOUNTERED, REMOVE UNSUITABLE MATERIAL AND REPLACE WITH SUITABLE MATERIAL AS DIRECTED BY THE ENGINEER. TRENCH WIDTH SHALL BE THE MINIMUM REQUIRED IN ORDER TO COMPLY WITH OSHA SAFETY STANDARDS. DIP AND PVC WHEN USED AS WATER MAIN SHALL NOT REQUIRE GRANULAR BEDDING OR COVER. PROVIDE UNIFORM AND CONTINUOUS SUPPORT OF PIPE BARREL BETWEEN BELL HOLES WATTRENCH.DWG TRENCH SECTION (WATER MAIN) WATER MAIN DRAWING NO. WM-11