CITY OF PITTSBURG ENGINEERING DEPARTMENT CONTRACT NO A WATER TREATEMENT PLANT CAPITAL IMPROVEMENTS PHASE 1A ADDENDUM #1 FENCE AND DITCH AUGUST
|
|
- Darren Harrison
- 5 years ago
- Views:
Transcription
1
2
3
4
5
6
7
8
9
10
11
12
13
14 CITY OF PITTSBURG ENGINEERING DEPARTMENT CONTRACT NO A WATER TREATEMENT PLANT CAPITAL IMPROVEMENTS PHASE 1A ADDENDUM #1 FENCE AND DITCH AUGUST 2014 CHAIN LINK FENCE SPECIFICATIONS Chain link fence, as follows: 8'0" high chain link fence plus 1'0", 3 strands of barbed wire at top (three-strand 45-degree arm angling the arm out from the secured area) for a total height of 9'0", consisting of 2-inch mesh 6 gauge chain link fabric, 2 3/8-inch line posts spaced a maximum of 10'0" o.c., 7 gauge coil spring wire at top, secured to the chain link fabric with 9 gauge hog rings spaced not greater than 12", 1 5/8-inch o.d. bottom rail, chain link fabric secured to line post and bottom rail at a maximum of 12 inches o.c. using 9 gauge tie wire. 2 7/8-inch o.d. end and corner posts complete with 1 5/8-inch o.d. brace rail, 3/8-inch truss assembly, 12 gauge tension bands secured at a maximum of 12 inches o.c., tension bar, necessary, fittings, nuts, bolts. bottom rail - the bottom of the fence with bottom rail shall be installed no greater than 2 inches above grade. Project inspection: There will be a mandatory requirement for reviewing material certifications and shop drawings prior to start of the project. This will ensure that proper products will be installed, and that specific installation guidelines have been provided. Typical detail: Typical detail of an eight foot high with one foot, 3-strand barbed wire security fence. Installation for the City of Pittsburg Water Treatment Plant will not include securing the bottom rail in the middle. Manufacturers A. Chain Link Fence: One of the following or equal: 1. Anchor Fence, Inc. Materials 2. Master-Halco A. Chain Link Fence. 1. Fabric: a. Height 1) Fence: 8 feet 0 inch b. Mesh: 2 inches, meet ASTM A 392, class 2b. c. Size Wire: 6 gauge. 1) Coating: Zinc coating ASTM A 395, class 1. 2) Tensile Strength: 80,000 pounds per square inch minimum. 3) Barbed Wire: a) Total Number Strands: 3 b) Wires per Strand: 2 c) Size Wires: 12 ½ gauge d) Barbs: 14 gauge 4 point at 3 inches on center. e) Coating: Galvanized, ASTM A 121, class 3 f) Color Coating: PVC, ASTM F 668, Color: Black 2. Rail: a. Size: 1 5/8 inch outside diameter, galvanized. b. Weight: 2.27 pounds per linear foot. c. Tension Wire: 7 gauge galvanized coil spring wire. d. Line Posts: 2 3/8 inch outside diameter, 3.65 pounds per linear foot, galvanized. 3. Terminal, Corner, And Pull Post: a. Size: 2 7/8 inches outside diameter round. b. Weight: 5.79 pounds per linear foot. 4. Color: Coat posts, rails and frame the same color as fabric and per ASTM F Accessories: a. Fence Fittings: Conform to ASTM F 626. b. Fencing Accessories: Post Top Fittings: Extension arms, 45-degree, double angle arms designed to carry total of 3 strands of barbed wire. 6. Fabric Accessories: B. Coatings: a. Wire Clips: Minimum 6 gauge hot-dip galvanized. b. Tension Bars: ¼ inch by ¾ inch, galvanized. c. Steel Bands: 11 gauge, one inch wide, hot dip galvanized. d. Bolts & Nuts: 3/8 inch diameter. e. Hot Rings: 11 gauges. 1. Galvanized Repair Paint: 2 component, moisture-cured, zinc-rich urethane primer, and minimum solids by volume of 83 percent plus or minus 2 percent. a) Manufacturers: One of the following or equal: 1) Tnemec' MANUFACTURED UNITS A. Chain Link Fence: 1. Pipe Post: Provide posts with caps that exclude moisture. FABRICATION A. Shop Finishing: 1. Galvanizing: For items not fabricated of galvanized materials hot-dip galvanize products after fabrication in accordance with following as applicable: a) ASTM A 123. b) ASTM A 153. c) ASTM A 385. d) Mark galvanized products with name of galvanize, applicable ASTM designation, and weight of zinc coating. e) Galvanize fabricated items complete, or in largest practicable sections. f) Provide galvanizing at rate of 2.0 ounces per square foot, minimum. B. Finish Schedule: 2. Ferrous Metal: a) Typical: Clean, then hot-dip galvanize in accordance with galvanizing standards. C.Field Finish Touch-Up Painting: 1. Galvanized Repair Paint: Apply paint having minimum dry film thickness of 2.0 to 3.5 mils. PREPARATION A. Surface Preparation: 1. Before locating fence post, grade ground to permit grade of fence to remain constant over any local elevations or depression in ground line. INSTALLATION: A.Fence and Gates: 1. Chain Link Fences And Gates: a) General: 1. Provide fence systems that are plumb, taut, true to line and grade, and complete in all details. 2. Install fencing to generally follow finish grade of concrete lined ditch and provide pull post at points where required to confirm to change in grade. 3. Install fencing such that space between bottom of fence and finished ground line does not exceed 2 inches B. Concrete Foundation For Fence Posts: 1. See cross section on Sheet CS-1ADD for installation of post within concrete lined ditch. 2. Set fence post in concrete foundations that extends at least 3 feet into ground (including concrete lined ditch) and space post not over 10 feet apart. 3. Provide concrete foundations having minimum 10 inches in diameter for line posts and 12 inches for corners and gates. 4. Finish exposed concrete fence post caps off in workmanlike manner. C. Post Bracing: 1. End Corner and Pull Post: Brace with same material as top rail and trussed to line posts with 3/8 inch rods and tighteners. 2. Bracing End, Corner, and Slope Posts. D. Rail: b) Brace to midpoint of nearest line post or posts with horizontal braces used as compression members. c) Then from such line posts truss from brace back to bottom of end, corner, slope, or gate post with 3/8 inch steel truss rods with turnbuckles or other suitable tightening devices used as tension members. 1. Install fencing with bottom rail and top tension wire. E. Fabric: 1. Place fabric on outward facing side of the posts and install so that the top edge protects over top rail of fence. 2. Stretch fabric taut and securely fasten to posts, top rail and bottom tension wire. 3. Install tension wire parallel to limit of fabric. 4. Fabric: Connect fabric to: a) Line posts with wire clips minimum every 14 inches. b) Terminal, corner, and gate posts with tension bars tied to posts minimum 14 inches on center and with steel bands and bolts and nuts. c) Tension wires with hog rings minimum 24 inches on center F. Post Top Fittings: Provide post tops with extension arms. CLEANING: A.Clean up surplus dirt, concrete and other waste material and dress grade up upon completion of the work B. Contractor to remove exciting fence and poles and dispose of materials. PROTECTION A.Protect existing improvements to remain and new improvement and, if damaged, repair prior to final inspection. MISCELLANEOUS A. Contractor responsible for notifying adjacent property owners of on going work. a. An initial letter shall be delivered to each affected residence 2 weeks prior to beginning work. The letter shall describe the work taking place, when the work will occur, how long the property owner will be without fencing and the contractor's contact information for coordinating special considerations (i.e. pets, existing improvements, etc.). b. One day prior to beginning work another letter shall be delivered to each affected residence as a reminder of the work to take place and shall include the contractor's contact information. B. Contractor responsible for coordinating animal control with property owners. CONTRACT A WATER TREATMENT PLANT SW RDA ADD #1 FENCE AND DITCH 1 of 8 TITLE SHEET NONE T - 1ADD
15 REMOVE (E) FENCING, POSTS AND AND POST FOUNDATIONS. BACKFILL HOLES WITH NATIVE MATERIAL TO 90% RELATIVE DENSITY 2 PROTECT IN PLACE (E) FENCE POST AND REUSE. 3 INSTALL CONCRETE LINED DITCH AND FENCE 4 INSTALL DITCH DISCHARGE, SEE DETAIL 1, SHEET C-1 5 INSTALL PLUG AT END OF DITCH, SEE DETAIL 2, SHEET C-1 6 EXPANSION JOINT SEE DETAIL 3, SHEET C-1 7 LIMIT OF CLEARING AND GRUBBING, GRADING AND IMPROVEMENT HYDROSEEDING 8 PROTECT (E) LIGHT POLE 9 AVAILABLE GRADING SOIL DISPOSAL AREA. CLEAR AND SCARIFY AREA, SPREAD SPOILS EVENLY OVER AREA, WHEEL ROLL TO COMPACT, AND HYDROSEED ANY DISTURBED AREAS. NO DISPOSAL OF "CLEAR AND GRUB" MATERIAL ON SITE. CONFIRM PLAN FOR SOIL DISPOSAL WITH ENGINEER PRIOR TO PROCEEDING. 2 C-1 IMPROVEMENT PLAN NTS 2 of 8 1 C-1 DITCH DISCHARGE 1" = 5' C - 1ADD VARIES DITCH PLUG ADDENDUM #1 FENCE AND DITCH NTS RDA EXPANSION JOINT CONTRACT A 3 C-1 SW 1 IMPROVEMENT NOTES
16 CONTRACT A ADDENDUM #1 FENCE AND DITCH PLAN AND PROFILE 148 STA: ELEV: STA: ELEV: % 3.30% 3.30% 3.30% 3.30% 3.30% 3.30% 3.30% 3.30% 148 SW RDA 1" = 5' % +/- 1.34% 2.26% 2.26% 3 of PP - 1ADD
17 STA: ELEV: % 4.25% 4.25% 4.25% 4.25% 4.25% 4.25% 4.25% 4.25% 4.25% 4.75% 4.75% 4.75% STA: ELEV: CONTRACT A ADDENDUM #1 FENCE AND DITCH SW RDA PLAN AND PROFILE 1" = 5' 4 of PP - 2ADD
18 '-2" STA: ELEV: % 4.75% 4.75% 4.75% 4.75% 4.75% 5.41% 5.41% 5.41% 5.41% 5.41% 5.41% 5.41% 5.41% 156 CONTRACT A ADDENDUM #1 FENCE AND DITCH SW RDA PLAN AND PROFILE 1" = 5' 5 of PP - 3ADD
19 CONTRACT A ADDENDUM #1 FENCE AND DITCH PLAN AND PROFILE STA: ELEV: % 1.39% 1.39% 1.39% 1.39% 1.39% 1.39% 168 SW RDA 1" = 5' % 5.05% 5.05% 5.05% 5.05% 5.05% of PP - 4ADD
20 CONTRACT A ADDENDUM #1 FENCE AND DITCH PLAN AND PROFILE SW RDA 1" = 5' % 1.39% 1.39% 1.39% 1.39% 1.39% 1.39% 1.39% 1.39% 1.39% of PP - 5ADD
21 ELEV = ELEV = ELEV = OFFSET=2.60 ELEV = ELEV = ELEV = OFFSET=1.88 ELEV = ELEV = ELEV = OFFSET=4.93 SURFACE FINISHES, NTS GENERAL NOTES: 1. LEFT OFFSET (-) IS TO TOP FACE OF CURB 2. RIGHT OFFSET (+) IS TO GRADING LIMIT 140 ELEV = ELEV = ELEV = OFFSET=2.82 ELEV = ELEV = ELEV = OFFSET=2.74 ELEV = ELEV = ELEV = OFFSET= ELEV = ELEV = ELEV = OFFSET= ELEV = ELEV = ELEV = OFFSET= ELEV = ELEV = ELEV = OFFSET= ELEV = ELEV = ELEV = OFFSET=3.29 ELEV = ELEV = ELEV = OFFSET=3.16 CROSS SECTION - STN TO , NTS SURFACE FINISHES, NTS CONTRACT A ADDENDUM #1 FENCE AND DITCH CROSS SECTIONS SW RDA VARIES 0+25 ELEV = ELEV = ELEV = ELEV = ELEV = OFFSET=2.84 ELEV = ELEV = OFFSET=2.44 ELEV = ELEV = ELEV = OFFSET=-2.22 ELEV = OFFSET=2.07 ELEV = OFFSET= CROSS SECTION STN 0+09 TO 0+16, NTS 8 of 8 CS - 1ADD
Item 550 Chain Link Fence
Item Chain Link Fence 1. DESCRIPTION 2. MATERIALS Furnish, install, remove, repair, or replace chain link fence and gates. Furnish certification from the chain link fence materials manufacturer stating
More informationTesting. Material testing will be according to applicable AASHTO, ASTM or Department methods as specified.
907.01 Section 907. FENCING MATERIALS 907.01 General Requirements. Materials for use in fencing property, right-of-way and other installations must comply with this section. 907.02 Testing. Material testing
More informationCity of Regina Standard Construction Specification SECTION 2660 CHAIN LINK FENCE
1.0 GENERAL 1.1 Scope 1.1.1 The work shall consist of supply and installing chain link fence, including braces and gates, as shown on the plans and specifications at the locations designated by the Engineer.
More informationSECTION CHAIN LINK FENCING
SECTION 32 31 13 CHAIN LINK FENCING PART 1 - GENERAL 1.01 SECTION INCLUDES A. The Work specified in this Section consists of furnishing and installing permanent chain link fences and gates in accordance
More informationSECTION CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP
1 1 1 0 1 0 1 0 1 SECTION 1 1 CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP BASED ON DFD MASTER SPECIFICATION DATED /01/ P A R T 1 - G E N E R A L SCOPE The work under this section shall consist of
More informationWAL-MART SUPERCENTER # ; Milwaukie, OR: SPECIFICATIONS. Revisions to Specification Fence
MILWAUKIE OR #3144-00 ADDENDUM #5 NARRATIVE: 11-08-12 WAL-MART SUPERCENTER #3144-00; Milwaukie, OR: SPECIFICATIONS SPECIFICATIONS Revisions to Specification 02822 Fence Spec division 02822 has been revised
More informationSection 808. FENCING
808.01 Section 808. FENCING 808.01. Description. This work consists of providing and erecting, or moving existing, woven wire fence, temporary fence, protective fence, chain link fence, high-tensile wire
More informationAPPENDIX FENCE GENERAL NOTES
APPENDIX FENCE GENERAL NOTES 1. Fabric: 9 gage, 2" mesh, knuckle top and bottom, placed on the outside of posts, single fabric width for the entire height. 2. All fencing to be standard galvanized finish.
More informationPART MATERIALS. Section Fencing Materials. Description
PART 03000 - MATERIALS Section 03010 - Fencing Materials Description 03010.00 Scope - This section consists of the test requirements, specifications and tolerances for barbed wire, woven wire and chain
More informationSECTION CHAIN LINK FENCING AND GATES
PART 1 GENERAL 1.01 SCOPE OF WORK A. The Contractor shall furnish and install all materials, labor, equipment and incidentals required to provide chain link fencing and gates as Shown on the Contract Drawings
More informationProject: # Solano Community College District
ADDENDUM #02 Project: #16 007 Solano Community College District Horticulture Site Improvements Date: April 26, 2016 The following clarifications are provided based on questions received or changes in District
More informationSECTION CHAIN LINK FENCE GALVANZED CHAIN LINK FABRIC ON GALVANIZED FRAMEWORK [Provided by Master Halco]
SECTION 32 31 13 CHAIN LINK FENCE GALVANZED CHAIN LINK FABRIC ON GALVANIZED FRAMEWORK [Provided by Master Halco] PART 1 GENERAL 1.01 SECTION INCLUDES A. Galvanized (zinc) coated chain link fabric with
More informationSECTION STRUCTURAL STEEL. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.
SECTION 051200 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting
More informationFEDERAL SPECIFICATION SHEET FENCING, WIRE AND POST, METAL (CHAIN-LINK FENCE ACCESSORIES) (DETAIL SPECIFICATION)
14 May 1990 SUPERSEDING RR- F-191/4C July 22, 1981 FEDERAL SPECIFICATION SHEET FENCING, WIRE AND POST, METAL (CHAIN-LINK FENCE ACCESSORIES) (DETAIL SPECIFICATION) IIIisFederal specification is approved
More informationSECTION SITE FURNISHINGS FOR CFCRT. 1. American Society for Testing and Materials (ASTM).
PART 1 - GENERAL 1.1 SECTION INCLUDES A. Benches. B. Trash receptacles. C. Bike storage. 1.2 REFERENCE STANDARDS A. Including but not limited to: 1. American Society for Testing and Materials (ASTM). 1.3
More information1.1 SUMMARY. A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards.
PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards. B. See Division 5 Section "Pipe and Tube Railings"
More informationSECTION TRAFFIC SIGNAGE
SECTION 10 14 53 TRAFFIC SIGNAGE PART 1 - GENERAL 1.01 SECTION INCLUDES A. Furnishing and installing roadside traffic signage. B. Providing additional traffic signs as required in Sections 01 55 28 Controlling
More informationSECTION METAL FABRICATIONS
SECTION 05100 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for metal fabrications, including minimum requirements for fabricator, and galvanizing. 1.02 REFERENCE STANDARDS A. ASTM
More information1. Layout. Step 1. Step 2. Step 3. Fig. 1
1-3/8 Panel Clamp Tools You Will Need: Tape Measure, Mason s String, Stakes, Hole Digger, Shovel, Level, Wheelbarrow, Wrenches or Adjustable Wrench, Hacksaw, Pliers, Cutting Pliers, Fence Stretcher and
More informationStandard Specification for Fence Fittings 1
Designation: F 626 08 Standard Specification for Fence Fittings 1 This standard is issued under the fixed designation F 626; the number immediately following the designation indicates the year of original
More informationSECTION CABLE TRAYS FOR COMMUNICATIONS SYSTEMS
SECTION 270536 - CABLE TRAYS FOR COMMUNICATIONS SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSW Region Asset Specifications: Four Strand Barbed Wire Fence Specifications
Lands Division Sustainable Resource Development SW Region Asset Specifications: Four Strand Barbed Wire Fence Specifications Prior to commencement of construction, contact must be made with the following
More informationCHAIN LINK FENCING DOCUMENT NUMBER: APPLICATION: ELEMENTARY, MIDDLE AND HIGH SCHOOL
CHAIN LINK FENCING DOCUMENT NUMBER: 02800 APPLICATION: ELEMENTARY, MIDDLE AND HIGH SCHOOL DATE OF ISSUE: 06-02-98 - miscellaneous revisions 08-06-97 - miscellaneous clarifications 06-02-97 - miscellaneous
More informationCOMPONENTS INSTALLATION
PIPE BRACE ASSEMBLY - 8' FIXED-KNOT FENCE Brace posts... 14'x 2 7/8" Structural Tubing Cross Members... 10'x 2 3/8 Structural Tubing Angle Brace... 12'x 2 3/8 Structural Tubing Angle Brace Foot... 6' x
More informationEMMEGI ARCHITECTURAL FENCING MASTER SPECIFICATION SECTION METAL FENCING, GATES & RAILING SYSTEM PART 1 GENERAL
EMMEGI ARCHITECTURAL FENCING MASTER SPECIFICATION SECTION 05720 METAL FENCING, GATES & RAILING SYSTEM PART 1 GENERAL EMMEGI ARCHITECTURAL FENCING is a high quality steel fencing system comprised of a hybrid
More informationFENCING PRODUCTS FENCING PRODUCTS. Please call:
YardGard brand of quality Chain Link borders and fencing meet the needs of residential property owners, industry and municipalities. Manufactured and distributed by Midwest Air Technologies, Inc,. F or
More informationA. Extent of structural precast concrete work is shown on drawings and in schedules.
SECTION 03 41 00 - STRUCTURAL PRECAST CONCRETE PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 specification
More informationINSTALLATION INSTRUCTIONS CHAIN-LINK FENCE AND GATE
INSTALLATION INSTRUCTIONS CHAIN-LINK FENCE AND GATE 1 BEFORE YOU START, IT S IMPORTANT TO CHECK......That fence footings do not exceed legally established property lines. If uncertain, refer to real estate
More information.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1.
PAGE 1 PART 1 GENERAL 1.1 REFERENCE.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. 1.2 RELATED WORK SPECIFIED ELSEWHERE.1 Installation
More informationSECTION STEEL LIGHTING STANDARDS. 1. Electrical conduit and fittings; Section
02760-1 of 5 SECTION 02760 STEEL LIGHTING STANDARDS 02760.01 GENERAL A. Description Steel lighting standards shall include, but not necessarily be limited to, furnishing and installing steel lighting poles,
More informationSECTION BULLET- RESISTANT DOORS
1 SECTION 08 3950 BULLET- RESISTANT DOORS PART 1- GENERAL 1.01 SUMMARY A. This Section Includes: 1. Bullet- resistant steel door and frame systems. 2. Door hardware for bullet- resistant steel door and
More informationIntroduction. Planning
Introduction Since fencing is such an important part of a livestock grazing system, the USDA- Natural Resources Conservation Service (NRCS) has developed specific designs and specifications for landowners
More informationSECTION 58 PRECAST CONCRETE BOX CULVERT. This work consists of furnishing and installing Pre-cast Concrete Box Culverts.
SECTION 58 PRECAST CONCRETE BOX CULVERT 58.1 DESCRIPTION A. General This work consists of furnishing and installing Pre-cast Concrete Box Culverts. B. Related Work Section 51 Section 52 Section 53 Section
More informationB. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.
SECTION 081113 - HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.
More informationSECTION STRUCTURAL STEEL FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 05 12 00 - STRUCTURAL STEEL FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION TRACER WIRE FOR NONMETALLIC PIPE
PART 1 GENERAL 1.1 DESCRIPTION A. The CONTRACTOR shall furnish and install a conductive tracer wire with all buried plastic water mains, services and appurtenances in accordance with the Water Utilities
More information4. Metal roof jacks at penetrations and attachments
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - SECTION 07 61 00 METAL SHINGLE ROOFING - - - - - - - - - - -
More informationNo No No
INSTALLATION, ASSEMBLY & MAINTENANCE MANUAL BASEBALL BACKSTOP No. 331025 No. 331036 No. 331039 No. 331025 No. 331036 No. 331039 INSTALLER NOTE: Upon completion of the installation/assembly of this baseball
More informationSECTION CABLE TRAYS
SECTION 16139 CABLE TRAYS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationTYPE J (20 FT - 40 FT) MICHIGAN DEPARTMENT OF TRANSPORTATION 10-0" 7-6" NOTE: sheet 5 & 6 of 10) DEPARTMENT DIRECTOR. Kirk T.
Column truss connection Chord splice (see details (See details sheets 3 & 4 of 10) s Top truss chord Free end panel 10-0" Support end panels length varies (See chart below) \ Truss Back truss chord Top
More information(50 FT FT) MICHIGAN DEPARTMENT OF TRANSPORTATION 10-0" 7-6" 8-0" 6-0" Truss Depth. 3" sheets 5 & 6 of 10) DEPARTMENT DIRECTOR. Kirk T.
Column truss connection (See details sheets 3 & 4 of 10) \ Span (Odd number of panels) \ Span (Even number of panels) Back truss chord Top truss chord \ Truss Chord splice Truss depth (See details \ Left
More informationB. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.
SECTION 081113 - HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.
More informationCertainTeed INSTALLATION GUIDE SIMTEK FENCE PRODUCTS. Fence Installation Guide 3', 4' & 6' High
CertainTeed INSTALLATION GUIDE SIMTEK FENCE PRODUCTS Fence Installation Guide 3', 4' & 6' High INSTALLATION GUIDE These instructions are designed to assist both professional installers and do-it-yourselfers
More informationDIVISION 6 WOOD AND PLASTICS
DIVISION 6 WOOD AND PLASTICS PART 1 - GENERAL 1.01 SUMMARY A. This Section includes the following: 1. Wood framing. 2. Wood supports. 3. Wood blocking. 4. Wood cants. 5. Wood nailers. 6. Wood furring.
More informationA. Deviation from this standard must be approved by the Project Architect.
September 2012, rev. 00 26 5600 Exterior Lighting PART 1. GENERAL 1.01 Related Documents A. Deviation from this standard must be approved by the Project Architect. B. Drawings and general provisions of
More information6a. Eight Steps to Chain-Link Fence Installation
6a. Eight Steps to Chain-Link Fence Installation Before You Start You will need the following tools to install your chain-link fence: Post hole digger Wheelbarrow, shovel and hoe for mixing concrete Tape
More information5/16" Flange nut. Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc plated bolt w/ washers and nut. Anchor 3" sq. 7 Ga.
2 1/2" x 2 1/2" x 10 Ga. 6" 5" 4" Variable Slipbase (8" Sq. SYS.) 5/16 Corner Bolt W/ nut 5/16" Flange nut Stub Insert (8" Sq. SYS.) Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc
More information6o ft (18.3 m) Southwest Windpower, Inc West Route 66 Flagstaff, Arizona USA Phone: Fax:
6o ft (18.3 m) sectional MONOPOLE TOWER INSTALLATION MANUAL Southwest Windpower, Inc. 1801 West Route 66 Flagstaff, Arizona 86001 USA Phone: 928.779.9463 Fax: 928.779.1485 www.skystreamenergy.com 3-CMLT-1390-01
More informationMidwest Roadside Safety Facility
B 64" 1626 602'-8 1/16" 183695 548'-0" 167030 1 2 3 4 5 6 7 8 9 10 11 12 14 15 16 17 18 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 373839 40 25 IMPACT 1500A 48" 12 27'-5" 8355 [] 3x7 CL A Galvanized
More informationLateral Support. Decks over 24 above grade require lateral support* *Exceptions to be discussed later
Lateral Support Decks over 24 above grade require lateral support* *Exceptions to be discussed later Decking Types of Decking: -2x4s & 2x6s -five quarter span rated decking boards -Wood plastic composite
More informationA. Columns: Worthington Millwork; Cellular Polyvinyl Chloride (PVC) columns; decorative, weatherproof, insect-proof, and highly durable.
WorthingtonWrap PVC Columns Architectural Specifications 1.1 SECTION INCLUDES A. Columns: Worthington Millwork; Cellular Polyvinyl Chloride (PVC) columns; decorative, weatherproof, insect-proof, and highly
More informationD. Thermally Sprayed Metallic Coating (Flame Spray): STD SPEC
STANDARD SPECIFICATION SECTION 05121 MISCELLANEOUS METALWORK PART 1 - GENERAL 1.01 DESCRIPTION This section includes materials, fabrication, and installation of structural steel, connecting bolts, pipes,
More informationRR-F-191/1D 14 May SUPERCEDING RR-F-191/1C July 22, 1981 FEDERAL SPECIFICATION SHEET
14 May 1990 ----------- SUPERCEDING RR-F-191/1C July 22, 1981 FEDERAL SPECIFICATION SHEET FENCING, WIRE AND POST METAL (CHAIN-LINK FENCE FABRIC) (DETAIL SPECIFICATION) This Federal Specification is approved
More informationSECTION CARPENTRY
SECTION 06100 CARPENTRY PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Carpentry work including grounds, nailers, blocking, miscellaneous framing, plywood backing panels, plywood sheathing, preservative
More informationSection 914. JOINT AND WATERPROOFING MATERIALS
914.01 Section 914. JOINT AND WATERPROOFING MATERIALS 914.01. General Requirements. Joint and waterproofing material for use in concrete construction must meet the requirements of this section. 914.02.
More informationGURANTEED TECHNICAL PARTICULARS OF BACK CLAMP FOR LT CROSS ARM
Technical Specification of Back Clamp for LT Cross Arm (MS) Back clamp for LT Cross Arm made out of 50 x 6mm MS Flat suitable for 8m X 300 Kg PSC poles. After fabrication the cross arm shall be painted
More informationHOW TO BUILD A DEER OR ELK-PROOF FENCE. Saskatchewan Environment Resource Stewardship Branch 112 Research Drive Saskatoon, Saskatchewan S7K 2H6
HOW TO BUILD A DEER OR ELK-PROOF FENCE Saskatchewan Environment Resource Stewardship Branch 112 Research Drive Saskatoon, Saskatchewan S7K 2H6 Revised March 2005 1 This information is intended to assist
More informationAnnie Tel: MSN: All chain-link fences aren't the same
Attractive, versatile and creative - a chain-link fence system can be an excellent choice. With the right fence you can expect years of protection, privacy and value. But as with any investment, it pays
More informationConstructing Wire Fences
1 of 6 12/3/2010 9:48 AM University of Missouri Extension G1192, Reviewed October 1993 Constructing Wire Fences Richard E. Phillips Department of Agricultural Engineering This guide will provide some basic
More informationFENCE INSTALLATION GUIDE 6 HIGH FENCE
FENCE INSTALLATION GUIDE 6 HIGH FENCE 1.866.648.9336 www.simtekfence.com INSTALLATION GUIDE These instructions are designed to assist both professional installers and do-it-yourselfers of SimTek decorative
More informationSPECIFICATIONS FOR THE MANUFACTURE AND DESIGN OF PRECAST THREE SIDED ARCH STRUCTURES, WINGWALLS AND HEADWALLS
SPECIFICATIONS FOR THE MANUFACTURE AND DESIGN OF PRECAST THREE SIDED ARCH STRUCTURES, WINGWALLS AND HEADWALLS 1. DESCRIPTION THESE SPECIFICATIONS ARE FOR A PRECAST THREE SIDED ARCH STRUCTURE, HEADWALLS
More information1.1 RELATED DOCUMENTS
SECTION 050505 -BEVEL RAIL ENDS PART 1- GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the contract, including General and Supplementary Conditions and Division 01 Specification Sections
More informationH HD Adult Wheelchair Swing Frame & Hangers(perm) IMPORTANT
Page 1 IMPORTANT PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment must be installed in accordance with these instructions. Check your shipment against Bill of Lading and Parts list.
More informationC. Samples for Initial Selection: Manufacturer's color charts showing the full range of colors available.
SECTION 105113 - METAL LOCKERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSHADOWBOX INSTALLATION FOR: Standard 6 H x 8 W Shadowbox Fence 5 x 5 Routed Posts Dog Ear or Straight-Edge Pickets 1.75 x 3.5 Rail
SHADOWBOX INSTALLATION FOR: Standard 6 H x 8 W Shadowbox Fence 5 x 5 Routed Posts Dog Ear or Straight-Edge Pickets 1.75 x 3.5 Rail Storage and Handling Fence Preparation and Layout Locate and Set Posts
More informationSE Region Asset Specifications Four Strand Barbed Wire Fence Specifications
Lands Division Sustainable Resource Development SE Region Asset Specifications Four Strand Barbed Wire Fence Specifications 1. Project Materials The contractor is to supply all the labour, tools and equipment
More informationRanch Rail Vinyl Fence
Ranch Rail Vinyl Fence INSTALLATION INSTRUCTIONS These instructions are to be used as general guidelines for the installation of your vinyl fence under normal installation conditions. Local conditions
More informationTENANT IMPROVEMENT 16 FEBRUARY WEST 27TH STREET, 4TH FLOOR 100% CD OWNER/BID ADD 1-03/08/2018
SECTION 055000 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationInstallation Guide. Capped Cellular PVC Fencing. Table of Contents. Storage and Handling Tools Needed Fence Layout and Locating Posts
Capped Cellular PVC Fencing Installation Guide Table of Contents Storage and Handling Tools Needed Fence Layout and Locating Posts Installation instructions 4 x 4 Over Sleeve Post - 3.5 Rail Privacy Shadowbox
More informationVersai Evolution of Versatile Fencing
Versai Evolution of Versatile Fencing About Versai Ornamental Fencing Versai Ornamental Fencing Versai Ornamental Fencing by Fortress is the next generation in ornamental fencing. It offers a solution
More informationFT DIX ELEMENTARY SCHOOL PHASE VII, CLASSROOM ADDITION PEMBERTON TOWNSHIP REGAN YOUNG ENGLAND BUTERA, PC PROJECT #5349A
SECTION 061050 - MISCELLANEOUS CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSTRUCTURAL STEEL AND ALUMINUM PART 1 - GENERAL 1.01 SCOPE:
SECTION 05100 STRUCTURAL STEEL AND ALUMINUM PART 1 - GENERAL 1.01 SCOPE: A. The WORK of this SECTION shall consist of furnishing all the labor, materials, and equipment necessary for installation of structural
More informationSUBMITTAL SHEET. Project Submittals by
Galvanized Tie Wire and Hanger Wire Submittal of Product Performance SUBMITTAL SHEET Project Submittals by GRABBER CONSTRUCTION PRODUCTS, INC. Submittal Date: Contract Number: Project Name: Section Number:
More informationInstallation Instructions. Tools Needed. Tape measure. Level. Shovel or Post hole digger. Concrete. Drill. Stakes. Mallet or hammer.
Installation Guide EcoStone Fence 1330 West 400 North Orem, UT 84057 Toll Free 1.866.648.9336 Tel. 1.801.655.5236 Fax 1.801.655.5240 www.ecostonefence.com Installation Instructions Introduction. These
More informationPost & Rail. Includes: Crossbuck, 2-Rail, 3-Rail and 4-Rail POST SUPPORT OPTIONS
Post & Rail Includes: Crossbuck, 2-Rail, 3-Rail and 4-Rail STAGGER RAIL ENDS FOR GREATER STRENGTH ALLOW 1-1/2" GAP ON HINGE SIDE OF GATE AND 1-1/4" ON LATCH SIDE OF GATE HARDWARE DIG HOLES 30" MINIMUM
More informationHEARNE STEEL CO., INC.
HEARNE STEEL CO., INC. INDUSTRIAL PARK 1011 VAUGHN LANE HEARNE, TEXAS 77859 Leading Manufacturers Of Chain Link Fence Fittings J.C. AMOS, (1921-2008) OFFICE ADDRESS: R.W. AMOS, President P. O. BOX 1239
More informationBARBARMS. IMPORT 2x1 5/8x45 degrees 2 3/8x1 5/8x45 degrees
BARBARMS IMPORT 2x1 5/8x45 degrees 2 3/8x1 5/8x45 degrees DOMESTIC Senior H Beam 1 5/8x1 5/8x45degrees Arm S-Slot 2x1 5/8x45 degrees Arm S-Slot 2 3/8x 1 5/8 45 degree Arm S-Slot 1 5/8x1 5/8 Vertical Arm
More informationSTEEL PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Pipe Rails and s shall be in accordance with ASTM A5 Grade B for standard weight pipe and ASTM A500 Grade B, C or D or ASTM A50 for structural tube. Bars for handrail supports
More informationALUMINUM PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Structural Tube, Pipe and Bar shall be in accordance with ASTM B22 or ASTM B429, Alloy 606-T6. End Rail 90 bends and corner bends with maximum 4-0" post spacing, may be Alloy
More informationContents. Grade 2, 5, 8 Hex Bolts 4. Heavy Hex Head Structural Bolts 6. A325 and A490 Tension Control Bolts (TC) 13. Nuts 22.
Who we are Amcan Jumax is the result of a merging between Boulons Jumax and Amcan Threaded Products, two successful companies well established, both with excellent reputations. The new entity is a bigger
More informationAsh Brook Golf Course Scotch Plains, New Jersey
SECTION 062013 - EXTERIOR FINISH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationCWM. Agricultural, Commercial, Industrial Product Brochure.
CWM Agricultural, Commercial, Industrial Product Brochure 1688 West 75 th Avenue Vancouver, BC V6P 6G2 Canada Canada Wire & Metal Inc is a Canadian based entity that was founded in 1994. We have been serving
More informationSECTION PRECAST CONCRETE SECTIONAL MANHOLES
SECTION 02545 PRECAST CONCRETE SECTIONAL MANHOLES PART 1 - GENERAL 1.01 SUMMARY A. Section Includes: 1. Precast reinforced concrete cylindrical sectional manholes, complete with openings, inserts, hardware,
More information1. ANSI/ASME Standard B , Square and Hex Bolts and Screws, Inch Series
SECTION 31 66 13 HELICAL PILES AND HELICAL ANCHORS PART 1 - GENERAL 1.1 DESCRIPTION A. This work pertains to furnishing and installing Helical Piles and Bracket Assemblies shown in the Contract in accordance
More informationMulti-Institutional Academic Health Science & Research Center Evansville, IN
SECTION 06 1053 - MISCELLANEOUS ROUGH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions Division 01 Specification
More informationManu International.
+91-8048723021 Manu International https://www.manuinternational.co.in/ We are amongst the renowned manufacturer, supplier and exporter of a vast array of Concertina Coil, Barb Arm, Ornamental Fence and
More informationSECTION SHEET METAL FLASHING AND TRIM
SECTION 07620 PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Formed roof drainage sheet metal fabrications. 2. Formed low-slope roof sheet metal fabrications. 1.2 SUBMITTALS A. Shop Drawings: Show
More informationELK EXCLUSION USING WOVEN WIRE FENCING
Fencing Order No. 307.252-1 September 2001 Agdex 724 ELK EXCLUSION USING WOVEN WIRE FENCING This factsheet outlines the use of woven wire to exclude elk in high pressure areas such as feed storage yards.
More informationSECTION HOLLOW METAL DOORS AND FRAMES
SECTION 081113 HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: Include construction details, material
More informationPost & Rail Crossbuck
Post & Rail Crossbuck 1. Getting Started 6. Crossbuck Be sure to call underground prior to digging Assemble gates (if necessary) and decide where they will be located Stake out the fence line Space and
More informationCollins Engineers Palmetto Islands County Park Boardwalk Repairs 03/28/2014 SECTION ROUGH CARPENTRY
PART 1 GENERAL 1.1 RELATED SECTIONS SECTION 061000 ROUGH CARPENTRY A. Drawings and general provisions of the Construction Contract, including General Conditions and Division 1 Specification Sections, apply
More informationSECTION MANHOLES
SECTION 33 05 13 MANHOLES PART 1 GENERAL 1.01 SECTION INCLUDES A. CONTRACTOR shall furnish and install precast concrete manhole base, sections, adjusting rings, steps, and manhole ring and cover, complete.
More informationH O O P RAC K. Simple Security
H O O P RAC K Simple Security The Hoop Rack is a proven design that provides high security and easy bike parking. The Hoop Rack uses thick pipe construction and the full radius of the bend makes the Hoop
More informationFENCE INSTALLATION GUIDE 8 HIGH WALLS
FENCE INSTALLATION GUIDE 8 HIGH WALLS 1.866.648.9336 www.simtekfence.com INSTALLATION GUIDE These instructions are designed to assist both professional installers and do-it-yourselfers of SimTek decorative
More informationPRIVACY INSTALLATION FOR: Standard 6 H x 8 W Privacy Fence 4 x 4 Post Sleeve & Brackets Dog Ear or Straight-Edge Pickets 1.75 x 3.
PRIVACY INSTALLATION FOR: Standard 6 H x 8 W Privacy Fence 4 x 4 Post Sleeve & Brackets Dog Ear or Straight-Edge Pickets 1.75 x 3.5 Rail Storage and Handling Fence Preparation and Layout Locate and Set
More informationFIRE STATION NO TH STREET NORTH ST. PETERSBURG, FL M-1 SCOPE OF WORK SYMBOL DESCRIPTION SYMBOL DESCRIPTION HVAC SYMBOL LEGEND
HVAC SYMBOL LEGEND HVAC PIPING AND VALVES LEGEND HVAC GENERAL NOTES SCOPE OF WORK SYMBOL DESCRIPTION SYMBOL DESCRIPTION SYMBOL DESCRIPTION SYMBOL DESCRIPTION PHASING OF WORK HVAC ABBREVIATIONS ABBREVIATION
More informationABOUT US. Our Mission. Our Vision. Providing safety living areas to the end users who would like to be in safe environment.
ABOUT US Our Company, Dogan Mesh Wire, was founded in 1968 and we are proud to share our 45 years of experience and knowledge with our customers. Since the year of the foundation; our company gives importance
More informationNON-ELECTRIC DOG FENCES
NON-ELECTRIC DOG FENCES Thank you! Thank you for ordering your non-electric dog fence kit from Pet Playgrounds. In less than a day you will have your very own personal dog park installed on your property.
More information1 of 6 SITE PLAN MW. Sample GAMECHANGE SOLAR. Sample. Sample AERIAL VIEW. Array Information. Design Information. Racking.
AERIAL VIEW Array Information PV Modules Racking Manufacturer NEO Solar Gamechange Racking Model D6M-B4A 23-Degree MaxSpan Dimensions Weight 77.0"x39.1"x1.57" 56.2 lbs Quantity 5184 407 Ground learance
More informationUP139 CRUISE-A-LONG (STANDARD) NATURAL COATED DECK COATED RAMP DESCRIPTION SQUIRREL PANEL BACK WALL CLEAR BUBBLE CRUISE RAIL SQUARE SPIRAL WHEEL 90 AN
UP39 CRUISE-A-LONG (STANDARD) NATURAL COATED DECK COATED RAMP DESCRIPTION SQUIRREL PANEL BACK WALL CLEAR BUBBLE CRUISE RAIL SQUARE SPIRAL WHEEL 90 ANGLE BRACKET TUBE BRACKET TUBE WARNING LABEL PLATE HARDWARE
More information