This is being reviewed, additional comment to follow Marmoleum tile has been removed and replaced with a biobased VCT.

Transcription

1 Dr. Checks Comment Responses Review: 100% Building Package B Review Project: (G168476) Ft. Gillem, Enclave Force Protection Latest Update: :30 am We will coordinate and add to the Life Safety (6A101) plans all such items as smoke detectors, pull stations, strobes, lighted exit signs, etc. Coordinate with E102 and E106. Verify which items will also be shown plans 1A101 and 2A Marmoleum tile has been removed and replaced with a biobased VCT. (used for LEED credit potential) The notations in the schedules will be revised to identify VCT, not MT This is being reviewed, additional comment to follow CAD drafting will be corrected CAD drafting will be corrected CAD drafting will be corrected Marmoleum tile has been removed and replaced with a biobased VCT. (used for LEED credit potential) The notations in the schedules will be revised to identify VCT, not MT CAD drafting will be corrected Provide any coordination with civil. Reviewer was not looking at civil drawings. We have provided stoops at entrances which tie into sidewalk layout This needs to be reviewed for cost implications. Do not think it should be a problem providing all insulating glass units in entry with tempered CAD drafting will be corrected CAD drafting will be corrected Horizontal mullion in storefront unit will be corrected to match exterior elevations. CAD drafting will be corrected.

2 CAD drafting will be corrected CAD drafting will be corrected CAD drafting will be corrected with addition of 5/8. Will need to research and provide UL# CAD drafting will be corrected CAD drafting will be corrected Changing doors from painted to stained needs to be reviewed by Slone/Batson-Cook. We may be able to provide factory prefinished stained doors for similar cost Door and window head, jamb and sill details can be added if required Hardware for bullet resistant doors will need to be given us for inclusion into the schedules. Batson-Cook should get supplier to provide info for hinges, locksets, closers, and any other required door hardware for this specialty item CAD drafting will be corrected. Verify that closer is added to this door provided by storefront installer Slone/Batson-Cook to verify which way they want to proceed. Remove noted bollards or add overhead chain stops CAD drafting will be corrected. Missing sheet was submitted back to Slone Slone/Batson-Cook to verify which way they want to proceed CAD drafting will be corrected CAD drafting will be corrected CAD drafting will be corrected Changing doors from painted to stained needs to be reviewed by Slone/Batson-Cook. We may be able to provide factory prefinished stained doors for similar cost Hardware for bullet resistant doors will need to be given us for inclusion into the schedules. Batson-Cook should get supplier to provide info for hinges, locksets, closers, and any other required door hardware for this specialty item.

3 The purpose of the hatch is to access attic area. Should we add walk boards around opening in attic, if so, how much? There is sufficient soffit structure that someone could access most of the area CAD drafting will be corrected CAD drafting will be corrected We were directed by Slone/Batson-Cook to change from synthetic marble stools to painted wood stools. Verify which is required to be provided We were directed by Slone/Batson-Cook to change from solid surfacing to plastic laminate. Verify which is required to be provided We were directed to provide VCT instead of porcelain tile, verify which is required to be provided This can be changed per comment form 36 x 36 to 36 x This can be provided by CID This can be provided by CID Marmoleum tile has been removed and replaced with a biobased VCT. (used for LEED credit potential) The notations in the schedules will be revised to identify VCT, not MT Optional power will be added for the optional rack A remote panel for the generator and the UPS per Army ACP Standard/ Criteria will be added A pull station for the gatehouse outside storage room will be added The drawings will be revised and the calculations will be revised to reflect EPACT 2005 energy efficiency requirements The increased load due to the quartz restrike lamps in the fixtures will be taken in to account and any circuit changes required will be reflected in the drawings This will need to be clarified by Slone, specs were set up per directions given us We will have to see if this can be corrected in SpecsNTack, the specification software required to be used Calculations will be appended to the design analysis.

4 We were directed by Slone/Batson-Cook to change from solid surfacing to plastic laminate. Verify which is required to be provided. Spec will be revised as directed We were directed by Slone/Batson-Cook to change from solid surfacing to plastic laminate. Verify which is required to be provided. Spec will be revised as directed We were directed by Slone/Batson-Cook to change from solid surfacing to plastic laminate. Verify which is required to be provided. Spec will be revised as directed We were directed by Slone/Batson-Cook to change from solid surfacing to plastic laminate. Verify which is required to be provided. Spec will be revised as directed Verify roofing warranty provided, update specs as directed Will remove paragraph about door louvers in spec Will remove Staved lumber from spec Will remove power operators form spec for bullet resistant doors Will revise note to correspond with desired wording We need to have supplier of bullet resistant window/door construction address this issue and provide information that can be included in drawings/specs Will review this and update spec as required Will remove plaster from title of spec Cat 5 will be changed to Cat 6 on drawing TA The backboard is based on the I3A design for a small facility. It is for the VCC. Clarification will be added to the detail. A new detail for the gatehouse will be added if necessary Shop drawings provided only showed one door, plan drawings were changed from two doors to one to correspond with this info The Riser detail will be revised to indicate specifics for the project Robert Beach will comment on Will clean up text in Basic Materials.

5 Will revise specification to reflect 2008 NEC Will revise Interior Distribution specification to include cable tray FIXTURES FOR HAZARDOUS LOCATIONS will be deleted from Interior Distribution Robert Beach will comment on Will indicate location of remote panel for the UPS in the Gatehouse Robert Beach will comment on Robert Beach will comment on Will coordinate and revise as necessary Corrected Will delete references to zinc anodes in Will delete references to incandescent lamps and light fixtures from Interior Lighting Robert Beach will comment on References to LPS will be deleted from the specification Robert Beach will comment on References to HPS will be deleted from the specification The specification will be edited to indicate cable trays. see # Robert Beach will comment on Specification will be edited to indicate IDS and Duress alarms are just rough in CID tor review Directional sign will be removed from , page Spec , page 10, para 2.11 reference color of signage to sheet 1A301.

6 Spec , page 10, para 3.1 reference signage schedule to the door schedule, sheet 1A Spec , page 6, para 2.9 Wall and Corner Guards. Correct reference to color from Color Schedule to reference 1A Spec , page 6, para 3.1.1, include locations of corner guards Relates to change of interior materials. Slone to verify direction CID tor review CID tor review MEP to review Slone should review and edit these specs for inclusion MEP to review MEP to review MEP to review MEP to review MEP to review MEP to review MEP to review MEP to review MEP to review MEP to review MEP to review MEP to review MEP to review MEP to review MEP to review MEP to review.

7 MEP to review MEP to review MEP to review MEP to review MEP to review MEP to review MEP to review Needs to be added to registry. Why is civil in this section? Why is civil in this section? Comment will be completed Comment will be completed Comment will be completed Comment will be completed Comment will be completed Comment will be completed Comment will be completed MEP to review MEP to review Please provide clarification how to proceed Mark McNamara directed that a cathodic system be included in Section LIGHTINING PROTECTION SYSTEM. WILL BE ADDED Please provide clarification how to proceed To be provided BES from Slone.

8