Bovard Studios Inc. Section April 6, 2004 Page 1

Size: px

Start display at page:

Download "Bovard Studios Inc. Section April 6, 2004 Page 1"

Tabitha Hart
5 years ago
Views:

1 April 6, 2004 Page 1 This section includes solid flush and surface articulated wood doors, may have veneer facing, solid or glazed (stained glass) design, factory pre-fit, may be factory finished or site finished. This section includes performance and descriptive type specifications. Edit to avoid conflicting requirements. Part 1 General 1.1 SECTION INCLUDES.1 Solid wood doors [and transom panels of [solid] [and] glazed design]..2 [Solid face] [Solid face and glazed] configuration..3 High quality hardware to suit door weight and service. 1.2 RELATED SECTIONS Select one or more of the following three paragraphs for frame type(s) required..1 Section [ - ]: Wood door frames. [OR].2 Section Custom Steel Frames..3 Section [ Stained Glass Windows:] [ Glazing:] Stained glass for wood doors. If factory finishing of wood doors is included in this section, delete the following paragraph..4 [Section Paint and Coatings: Site finishing of wood doors.] 1.3 REFERENCES List reference standards that are included within the text of this section..1 AWI (Architectural Woodwork Institute): Quality Standards. 1.4 QUALITY REQUIREMENTS.1 Door Construction: To AWI quality requirements specified in this section..2 Door Mass (Weight) - Approximate: <[ ] lbs> <<[ ] kg>>..3 Door Movement:.1 Smooth to the touch..2 With no self-movement due to gravity at any open position (with mechanical closer detached).

2 April 6, 2004 Page SUBMITTALS FOR REVIEW The following submittals are intended for Consultant and Owner review of door and stained glass design..1 Section 01300: Submission procedures..2 Product Data: Indicate door core materials and construction, wood [and veneer] species, and weight characteristics..3 Shop Drawings: Illustrate door opening criteria, elevations, sizes, types, swings, [special beveling,] [special blocking for hardware,] [factory machining criteria,] [factory finishing criteria,] identify cutouts for [glazing,] [hardware,] [and] [ ]. Include the following paragraph for submission of samples for selection of factory finish or site applied stain, colour, sheen, etc..4 Samples: Submit [two] [ ] samples of door surface, <[ x ] mm> <<[ x ] inch >>in size illustrating wood grain, stain colour, and sheen. 1.6 SUBMITTALS FOR INFORMATION The following submittals are informational; responsive action by the Consultant is not required..1 Section 01300: Submission procedures..2 Manufacturer's Installation Instructions: Indicate special installation instructions. 1.7 QUALITY ASSURANCE Select the quality level required for the project. Utilize this article when one quality level applies to all doors. If the project requires two or more quality levels, delete this article and edit the quality level required in each article or paragraph in this section. Include the last sentence of the following paragraph only when the costs of acquiring the specified standards are justified..1 Perform work in accordance AWI Quality Standard, Premium grade. Include the following paragraph if factory finishing is specified..2 Finish doors to a quality consistent with the AWI Premium grade specified..3 Manufacturer: Company specializing in manufacturing the Products specified in this section with minimum [Five (5)] [ ] years documented experience. 1.8 DELIVERY, STORAGE, AND PROTECTION.1 Section 01600: Transport, handle, store, and protect products..2 Accept doors on site in manufacturer's packaging. Inspect for damage. 1.9 PROJECT CONDITIONS.1 Section 01300: Coordination and meetings.

3 April 6, 2004 Page 3.2 Coordinate the work with door opening construction, and surrounding Work WARRANTY Improper specifying of warranty and correction period extensions may limit the statutory rights of the owner and the ability to enforce claims under a contractor's contractual warranty. Consult legal counsel before editing this article. Extended door warranties (beyond one year) are manufacturer's warranties and should be provided to the owner, in the owner's name. Investigate before specifying any term period beyond one year. Warranty may include statements such as delamination of veneer facing, warping, or defective materials..1 Section 01700: Warranties and bonds..2 Provide warranty to the following term:.1 Exterior Doors: [Five (5)] [ ] years..2 Interior Doors: [Two (2)] [ ] years..3 Include coverage for [delamination of veneer,] [warping beyond specified installation tolerances,] [defective materials,] [telegraphing core construction,] [ ]. Part 2 Products 2.1 MANUFACTURERS In this article, list the manufacturers acceptable for this project. Edit the subsequent descriptive specifications to identify project requirements and to eliminate any conflict with specified manufacturer's products..1 Bovard Studios, [Style] [Model] [ ]..2 Substitutions: [Refer to Section ] [Not permitted.] 2.2 DOOR [AND TRANSOM PANEL] TYPES.1 Door Face Design:.1 Interior, [flush] [stile and rail] [ ]..2 Exterior, [flush] [stile and rail] [ ]..2 Wood Face Species (Interior):.1 Clear [Alder] [Teak] [Beech] [White Birch] [ ]..2 Kiln dried to less than [10] [ ] %..3 Wood Face Species (Exterior):.1 [Cherry] [Mahogany] [Walnut] [Pine] [Fir] [Ash] [Birch] [Hemlock] [Maple] [ ]..2 Kiln dried to less than [10] [ ] %..4 Door [and Transom] Core:

4 April 6, 2004 Page 4.1 Exterior: <[57] [ ] mm> <<[2-1/4] [ ] inches>> thick; solid core construction of [ ] wood species..2 Interior: <[44] [57] [ ] mm> <<[1-3/4] [2-1/4] [ ] inches>> thick; solid core construction of [ ] wood species..5 Transom Panel Finish:.1 [To match door.] [Face veneer to [end] [ ] match door finish below.].2 [Stained glass with special design.] [.] 2.3 ADHESIVE Type I adhesive is more moisture resistant than Type II. For exterior doors select Type I adhesive..1 Facing Adhesive: Type [I - waterproof] [II - water resistant]. 2.4 ACCESSORIES Select and edit the following paragraphs, dependant on glass and glazing design intended..1 Glazing:.1 Outer Protective Glass: [Tempered.] [Safety.] [Laminated.] [.].2 Decorative Glass: Stained glass, set in [lead] [ ] came, special design and colors..3 Inner Pane: Clear glass, single pane of [tempered.] [safety.] [laminated.] [.].2 [Glass] [Panel] Shape and Profile:.1 Panels: [ ]..2 Carved: [ ]..3 Arch: [ ]. When specifying wood stops for fire rated doors, metal clips are required..3 Glazing Technique: Refer to Section Special hardware may be required for doors. Check with hardware supplier for weight of door and force ratings on hardware. Select either the first paragraph below or edit the subsequent paragraphs..4 Hardware:.1 [Refer to Section Door Hardware.].2 Hinges: [1-1/2 pair] [2-pair], [steel] [brass] [ ] material, ball bearing knuckles, [ ] style..3 [Handset:] [Latch:] [ ]..4 Closer [and Coordinator]: [ ]..5 Door Stop: [ ]..6 Hardware Finish: [ ]..7 Astragal: [Wood,] [Metal,] [T] [L] shape.

5 April 6, 2004 Page 5.8 Weatherstripping: [ ] type. 2.5 FABRICATION.1 Fabricate doors [and transom] in accordance to AWI Premium grade..2 Prepare doors for [glazing] [and] [hardware]..3 Provide solid lock blocks at [lock edge] [and] [top of door for closer] for hardware reinforcement..4 Vertical Exposed Edge of Stiles:.1 [Of same species as veneer facing.].2 [Hardwood] [Softwood] for [paint] [transparent] finish..3 Fit door edge trim to edge of stiles after applying veneer facing..4 Bond edge banding to cores..5 At exterior doors, provide [aluminum] [copper] [ ] fla shing at the [top and bottom rail] [and] [the sill of glazed openings for full thickness and width of door]. Utilize the following paragraph when factory machining for hardware is required. Special blocking may be required for through bolting of hardware; specify accordingly..6 Factory machine doors for finish hardware.1 Prepare in accordance with hardware requirements and dimensions..2 Do not machine for surface hardware..3 Provide solid blocking for through bolted hardware. Utilize the following paragraph when factory fitting is required..7 Factory fit doors for frame opening dimensions identified on shop drawings..8 Cut and configure exterior door edge to receive recessed weather stripping devices as per manufacturers instructions. 2.6 FINISH This article describes factory finishing of wood doors. The three finish types indicated are commonly available for wood doors. If more than one colour or sheen is required for several doors, it may be appropriate to incorporate a schedule at end of this section..1 Finish: [Transparent,] [Opaque,] [conversion varnish,] [vinyl catalysed,] [catalysed polyurethane,] AWI Premium quality, [ ] sheen. Include the following paragraph when the door top edge is visible from above, such as a mezzanine..2 Seal door top edge with [color] [ ] sealer to match door facing.

6 April 6, 2004 Page 6 Part 3 Execution 3.1 EXAMINATION.1 Section 01700: Verification of existing conditions before starting work..2 Verify that opening sizes and tolerances are acceptable..3 Do not install doors in frame openings that are not plumb or are out-of-tolerance for size or alignment. 3.2 INSTALLATION.1 Trim door width by cutting equally on both jamb edges..2 Trim door height by cutting bottom edges to a maximum of <[ ] mm> <<[ ] inch>>..3 Machine cut for hardware..4 Coordinate installation of doors with installation of frames specified in Section [08114] [ ], [and hardware specified in Section ].5 Coordinate installation of glass and glazing. 3.3 INSTALLATION TOLERANCES.1 Maximum Diagonal Distortion (Warp): <[3] [ ] mm> <<[1/8] [ ] inch>> measured with straight edge or taut string, corner to corner, over the diagonal surface of the door area..2 Maximum Vertical Distortion (Bow): <[3] [ ] mm> <<[1/8] [ ] inch>> measured with straight edge or taut string, top to bottom, over height of door at any vertical position..3 Maximum Width Distortion (Cup): <[3] [ ] mm> <<[1/8] [ ] inch>> measured with straight edge or taut string, edge to edge, over width of door at any horizontal position. 3.4 ADJUSTING.1 Section 01700: Adjusting installed work..2 Adjust door for smooth and balanced door movement..3 Adjust closer for full closure. 3.5 SCHEDULE Provide schedule when door and frame schedules are not described on drawings. The schedule should identify various types or categories of doors and associated frames, hardware sets, etc..1 [ ].

7 April 6, 2004 Page 7 END OF SECTION

SECTION WOOD DOORS

SECTION WOOD DOORS SECTION 08211 WOOD DOORS Notice to Vendors: CANV prefers to purchase products that contain tropical wood only if they are certified according to the guidelines of the Forest Stewardship Council (FSC).