1010 Sliding Mall Front

Transcription

1 JUNE, 2018 FEATURES 1 Features Screw spline fabrication 1/4" and 1" glazing Permanodic TM anodized finishes in seven standard choices Painted finishes in forty-two standard choices and unlimited custom choices Product Applications The is a multi-track unit primarily for interior applications. It is ideally suited for the following comerical applications: Enclosed shopping malls Sliding room dividers Institutional sliding doors Interior pocket doors For specific product applications, Consult your Kawneer representative.

2 2 BLANK PAGE JUNE, 2018

3 JUNE, 2018 INDEX 3 Architects - The extrusions and sliding mall front types illustrated in this catalog are standard products for Kawneer. These concepts have been expanded and modified to afford you design freedom. Please contact your Kawneer representative for further assistance. ELEVATIONS/VERTICAL SECTION DETAILS...5 HORIZONTAL SECTION DETAILS...6 SIZE LIMITATIONS AND GLAZING OPTIONS...7 HARDWARE...8 LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR. Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses ( ) are millimeters unless otherwise noted. The following metric (SI ) units are found in these details: m meter cm centimeter mm millimeter s second Pa pascal MPa megapascal

4 4 BLANK PAGE JUNE, 2018

5 JUNE, 2018 ELEVATIONS / VERTICAL SECTION DETAILS 5 Additional information and CAD details are available at www. NOTE: DOTTED LINES ON PLAN INDICATE OPTIONAL TRACK LAYOUT, OTHER CONFIGURATIONS AVAILABLE USING STANDARD COMPONENTS SHOWN O X X O O X X X X O A A B B C C P 4 5 X X X X P O O X X O D D E E ELEVATIONS KEYED TO DETAILS BELOW AND ON PAGE /4" 1-3/8" (82.6) (34.9) 4 HEAD SILL HEAD SILL OPTIONAL: TRACK MAY BE RECESSED INTO FLOOR AT ONE OR BOTH SIDES NOTE: PROPER SUPPORT MUST BE PROVIDED FOR FLOOR AND HEAD TRACK. HEAD SILL FLOOR LINE HEAD SILL 5 3-1/4" 1-3/8" (82.6) (34.9)

6 6 HORIZONTAL SECTION DETAILS Additional information and CAD details are available at www. JUNE, " (25.4) 1-3/4" (44.5) SECTION A-A 2-1/2" (83.5) SECTION B-B 2-1/2" (63.5) 5-1/8" (130.1) MEETING STILES 3-7/16" (87.3) SECTION C-C LOCK JAMB LOCK JAMB NOTE: POCKET DEPTH EQUALS PANEL WIDTH PLUS 5". 1-3/4" (44.5) INTERLOCK JAMB INTERLOCK SECTION D-D MEETING STILES SECTION E-E INTERLOCK JAMB INTERLOCK 1-3/4" (44.5) 1-1/2" (38.1) 2-1/4" (57.1) FIXED STILE MULLION MEETING STILES

7 JUNE, 2018 SIZE LIMITATIONS AND GLAZING OPTIONS 7 Additional information and CAD details are available at www. MAXIMUM PANEL SIZE CHART INTERIOR APPLICATIONS ONLY HEIGHT IN FEET WIDTH IN METERS A B WIDTH IN FEET HEIGHT IN METERS A: Maximum panel size with standard interlocks (single glazing). -AND- Maximum panel size for double glazed units. B: Maximum panle size with heavy duty interlocks (single glazing). C: Panel width should be at least 1/3 panel height GENERAL NOTES: 1. ON PANELS OVER 10' IN HEIGHT AN INTERMIEDIATE HORIZONTAL MUNTIN IS RECOMMENDED. 2. THIS IS NOT A WINDLOAD CHART FOR EXTERIOR APPLICATIONS. 3/16" (4.8) 7/32" (5.6) 1/4" (6.4) SINGLE GLAZING GLAZING OPTIONS AVAILABLE 3/8" (9.5) SINGLE GLAZING AND 5/8" (15.9) 1" (25.4) DOUBLE GLAZING 1-3/4" (44.5) 1" (25.4) GLAZING MUNTIN

8 8 HARDWARE JUNE, 2018 TANDEM CASTER FLUSH FACE PULL ADAMS RITE MS 1850A-505 HOOK BOLT LOCK EXTRUDED PULL (OPTIONAL) EDGE PULL (OPTIONAL) Standard Offering Tandem Casters Adams Rite Maimum Security 1850A-505 Hookbolt Lock 1-5/32" (29.3) cylinders - (1) interior, (1) exterior Flush Face Pulls Optional Offering Extruded pull in lieu of flush face pull Thumbturn (in lieu of interior cylinder) Adams Rite 1848 Hockbolt Lock with 5 pin cylinder (in lieu of Adams Rite M.S. 1850A-505) Stainless steel hookbolt and strike (not compatible with AR.M.S. 1850A-505) Bottom rail lock Cylinder operated flush bolts Manually operated flush bolts Limitations Interlock stiles require notching if the lock cylinders for the Adams Rite M.S. 1850A-505 are to bypass the stiles. Thumbturns will not bypass interlock stiles.