182.1 INTRODUCTION SERIES 462 ARCHITECTURAL COMMERCIAL SLIDING WINDOW. Design Features : Australian Registered Design.

Transcription

1 INTRODUCTION DATE JUN 06 REPLACES NOV 04 SCALE NOT TO SCALE Design Features : The 26mm thick heavy duty sliding window sashes have been fitted into custom head and sill and jamb inlay adaptor that snaps to standard 30mm frame as shown right or alternative 44mm wide jamb. The extra strong sashes allow large sash windows to be fabricated for high wind load areas. Double sash design with the external sash fixed. Both fixed and opening sashes can be installed, replaced and/or reglazed from inside the building. This could be an important feature in elevated situations There is a large variety of window combinations possible (SF, FS, SFS or FSSF) with and without highlights/lowlights. 102mm x 44mm head and sill, 102mm x 30mm jamb, 44mm mullion and 44mm transoms match. Sliders can be fitted with surface or mortice deadlocks. Sashes run on heavy duty wheel carriages. Two flyscreen options: * No flyscreens - Frame fitted with cavity closers so there are no unwanted recesses to catch dust, water and bugs, as shown below. * Conventional flyscreens- Two new conventional size extruded flyscreen frames (25 x 11) can be fitted into the window using custom frame trims to accept the screen, refer details in these notes. Co-extruded PVC sill seal keeps water out of the system. We have built-in the patented ball valve drainage to transfer any water that may get into the drainage trough to the tubular sump sill, this valve also reduces blow-back through the hooded external drainage holes. Unwanted frame recesses are fitted with snap-in flat closers to ensure that the clean looks are maintained. It's possible to re-hand the window on-site (change type 'SF' to 'FS') depending on what lock has been used. Sashes and sidelights will accept a variety of glass thicknesses from 4mm to 20mm insulating glass units. Dedicated sash rail and stiles for 16mm IGU's. We have 90 and 135 corner mullions for bay and box windows. Australian Registered Design. AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 182.1

2 TYPICAL CONFIGURATIONS DATE JUN 06 REPLACES NOV 04 SCALE NOT TO SCALE Series 462 can be fabricated as 'SF', 'FS', 'SFS' and 'FSSF' with lowlights and/or highlights as shown above. The illustration left shows how the unwanted recesses are closed off to improve weather performance and appearance. Safety Glass: On the example below the door panel and the two sashes in the sliding window sidelights would require grade 'A' safety glass. If the opening sash was in the open position it would be within 300mm of the door opening. Refer Australian Standard AS1288 for more information. Alternative 44mm wide transom illustrated. Water Resistance: We always recommend the use of sub-sills under commercial frames AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

3 SASH STRENGTH DATE JUN 06 REPLACES NOV 04 SCALE NOT TO SCALE 'SF' and 'FS' windows Height W idth Meeting stile combinations mm mm Light Medium Heavy L/180 S L/250 S U L/180 S L/250 S U L/180 S L/250 S U L/180 S L/250 S U Rating tables for window meeting stiles on this page. S = Serviceability limit state (deflection = L/180 or deflection L/250). U = Ultimate strength limit state (factored yield strength = 104 MPa). These tables have been calculated using nominal section properties. A typical assembly has been tested as per the requirements of AS2047, Serviceability rating has been limited to 3333 Pa and Ultimate strength rating has been limited to 5000 Pa. Table Wind Ratings (Pa) 'SFS' windows Height W idth Meeting stile combinations mm mm Light Medium Heavy L/180 S L/250 S U L/180 S L/250 S U L/180 S L/250 S U L/180 S L/250 S U L/180 S L/250 S U Table Wind Ratings (Pa) 1/4 1/2 1/4 'FSSF' w indow s Height W idth Meeting stile combinations mm mm Light Medium Heavy L/180 S L/250 S U L/180 S L/250 S U L/180 S L/250 S U L/180 S L/250 S U L/180 S L/250 S U Table Wind Ratings (Pa) Type 'FSSF' windows are limited by the strength of the centre meeting stiles (42010 with 42054). Meeting stile combinations External Internal Light Medium Heavy Details on meeting stiles are shown on earlier pages. AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 182.3

4 HEAD AND SILL DETAILS DATE JUN 06 REPLACES NOV 04 SCALE FULL SIZE Head We have a dedicated head section to allow the installation of sliding window sashes into framing. The nailing fin aligns with the dedicated nailing fin jamb shown on following page. This nailing fin also aligns with the snap-in nailing fin adaptor used on narrow frame and custom nailing fin sub-sill. The weather bar on the head is used to seal transom details. Weatherpile seals. Unwanted recess closed off. If there are no flyscreens we fit the flat filler as shown on this detail. If there are flyscreens we use a custom filler to suit the flyscreens, refer flyscreening page later in these notes. For the best flyscreening finish always specify AWS flyscreens and from an approved fabricator. Sill We have a dedicated sill section to allow the installation of sliding window sashes framing. Removable running rail. Patented ball drainage valve. Important Note: Overall frame height includes the nailing fin sub-sill and is measured to the external lower edge, refer '!'.! AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

5 JAMB DETAIL DATE JUN 06 REPLACES MAR 04 SCALE FULL SIZE Jamb Custom jamb adaptor snaps into nailing fin jamb. The detail left shows the standard 30mm narrow jamb. We also have a 44mm wide nailing fin jamb. Standard 30mm jamb Window can be fitted with surface mounted or mortice type locks. You can view the lock options in colour on our web site Sub-sill fitted under Series 462 sliding windows. CAD file: DWG or DXF AWS_462_1 AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 182.5

6 HORIZONTAL SECTION THROUGH 'FS' WINDOW DATE JUN 06 REPLACES NOV 04 SCALE HALF FULL SIZE Stainless steel screw assembly. Standard 30mm jamb The nailing fin frame is ideal for brick veneer and cavity brick wall installation. External recess in frame can be closed off with optional jamb filler if required. Alternative 44mm wide jamb. All unwanted internal and external recesses are closed off with snap-in flat closer. Adhesive buffer at head and sill. Fixed sash bottoms out on the stop leg to position this sash in the correct location. Double weatherpile seals at meeting stiles. The standard mullion meeting stile illustrated will cover most situations, but for exposed areas you may have to use the heavier meeting stile on the inside as shown dotted. Wrap around PVC glazing channel wedge. Surface mounted Albany lock option illustrated, refer lock identification page for other alternatives. Weatherpile seals AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

7 DRAINAGE DATE JUN 06 REPLACES NOV 04 SCALE FULL SIZE & NTS Alternative 44mm wide jamb. Ball valve. Alternative 44mm wide jamb. Flat filler closes off all unwanted recess in perimeter frame inside and out. Sill running rail covers the drainage ball valve and stops short both ends to allow water escape. If necessary in the future this running rail can be removed / replaced. The legs on running rail give the impression that the sill recess is shallow. Nylon drainage hood. AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 182.7

8 FLYSCREENING DATE JUN 06 REPLACES NOV 04 SCALE HALF FULL SIZE Weatherpile flyscreen as drawn barrier frame available. Nylon flyscreen corner stake PVC flyscreen spline. Flymesh Flyscreen height = S Important Note: Flyscreen inlay adaptor replaces the flat filler when screens are required. Don't fit this recessed adaptor to windows without screens as this would channel too much water into the sill area. Don't fit weatherpile seal to sill infill as this gap allows water to escape into the sump area. Spacer block ensures that water can escape under the screen and into the drainage system Most Important: Don't drill drainage holes down into the sump under the flyscreen as this extra water has a detrimental impact on the window water resistance. Water is drained out via the hooded drainage hole/s in the front leg under the screen at meeting stiles. Flyscreen supported at mullion with channel (72817), fix channel to mullion with 3mm blind 450mm maximum centres Nylon flyscreen clip, part of type 'SF' Flyscreen width = W/2-76 type 'SFS' Flyscreen width = W/ type 'FSSF' Flyscreen width = W/ Note: Based on standard 30mm jambs AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

9 Design Details Series 462 Architectural Commercial Sliding Windows Note: The following 'Design Details' have been produced to assist architects and designers in the use of Architectural Window Systems (AWS) Series 462 Architectuarl commercial sliding window systems. All care has been taken in the production of these pages, but Architectural Window Systems Pty Ltd can take no responsibility for errors. If you should find any errors please contact your local AWS sales office. Details are subject to change without notice. The latest information can be accessed on our web site

10 INDEX DATE JUN 06 REPLACES NOV 04 SCALE Page Contents Introduction Typical configurations Sash strength Head and sill details Jamb detail Horizontal section through 'FS' window Drainage Flyscreening AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE