Unit 9. Wall and Ceiling Framing
|
|
- Theodora Moody
- 6 years ago
- Views:
Transcription
1 Unit 9 Wall and Ceiling Framing
2 Wall construction Wall framing includes the assembly of horizontal and vertical members that make up exterior walls and interior partitions. Theses walls support the ceilings and roof of a house and sometimes support a second floor as well. Walls can be framed using 2 X4 lumber for garages and other non-residential construction. For residential construction walls are framed using 2 X6 material.
3 Wall construction Cont. In platform framing, walls are constructed laying down on the platform and then raised into position. Interior walls are called partitions and are constructed in a similar manner to exterior walls. Interior load bearing walls construction is identical to exterior walls as they are designed to carry loads from the roof, ceiling and upper floors.
4 Parts of the wall framing Sole plate Top plate Studs Cripple studs Sill Jack studs or trimmer Headers or Lintels
5 Sole plate This is the part at the bottom of a wall that rests on the platform. The studs attach to the sole plate using 3 1/2 nails. Once the wall is in place, it is attached to the platform by driving nails through the sole plate and in to the platform.
6 Top Plate This is the part at the top of the wall. The studs attach to the top plate using 3 1/2 nails. The top plate may be doubled to provide adequate support for the top of the wall. The ceiling or upper floor will sit on the top plate.
7 Studs Wall studs provide a place to attach interior and exterior finishing. Usually spaced 16 O.C. but can be 24 on some one story older homes. On exterior walls, the void between studs provide an area for the installation of insulation.
8 Studs Cont. Extra studs are used in the corners, around openings in the wall for doors and windows and where interior partitions attach to exterior walls. The height of exterior wall is generally 8 but it is not uncommon to find wall 10 or higher. Stud length lumber measures 92 5/8 long.
9 Cripple studs Full length studs become cripple studs when they end because of an opening such as a window
10 Sill The sill makes up the bottom of a rough window opening. It provides support for the window when it is installed as well as a place for the top of the cripple studs to attach.
11 Jack or Trimmer Studs Shortened studs that stiffen the sides of a rough opening. They bear the weight of the header.
12 Figure 9-10 p209 text
13 Important things to remember about wall framing Stud spacing remains the same regardless of openings for doors or windows. This is so that sheathing can be installed with little cutting or waste. Wall framing lumber must be straight. This is especially true for interior partitions. Be sure to turn the crown of the lumber all the same way, either all facing in or all facing out.
14 Framing for corners Corners are formed when two walls intersect in a building. Only straight lumber should be used for framing corners. Usually a second stud is spaced the thickness of a 2 X4 and blocks are installed in 3 or 4 places from top to bottom to keep spacing consistent. The blocks allow the extra stud to stick out past the end wall giving an area to fasten interior finishes. This type of corner requires insulation to be installed before they are attached together.
15
16 Framing for corners Another method commonly used is to place a stud at a 90 o to the stud at the end of the wall. This stud is placed so it will be closest to the interior side of the wall. This stud will stick out past the inside of the end wall providing a place to fasten interior finishes. This type of corner construction allows for the corner to be insulated after the walls are erected.
17 Fig 9-4 p207 text
18 Framing required for Partition Intersections. Partitions need to be fastened firmly to the exterior walls. This requires some extra framing. The extra framing must not only provide a surface to securely fasten the partition but also provide a nailing surface for interior finishing.
19 Framing required for Partition Intersections. Cont. This can be accomplished by several methods Install extra studs in the outside and attach the partition to them. Insert blocking and nailers between the regular studs.
20 Fig 9-6 page 208 text
21 Rough Openings A rough opening is the opening left in a wall that will contain a window or a door in most cases. It is called a rough opening because it is larger than the true size of the window or door to be installed. It is usually 1 1/2 larger to allow for shimming of the door or window to be installed.
22 Rough Openings Cont. Generally the height of all rough openings are the same from one floor to the next. This information can be found on the elevation drawings and sectioning view. The size of the opening can be found on the plan view and window/door schedule.
23 Rough Openings Cont. Rough openings must contain a header or lintel. The header carries any weight placed over the opening and transfers it to the framing on either side of the opening. Headers are constructed by nailing two framing members together on edge. The longer the span, the larger the header must be. Plywood spacers make the header the same thickness as the wall.
24 Rough Openings Cont. The header length is equal to the size of the rough opening plus the thickness of two trimmer studs (3 ). The studs and trimmer support the header and provide a nailing surface for the door and window casings. In some cases the sill may be doubled to provide a nailing surface for trim.
25 Figure 9-8 page 209 text
26 Figure 9-11 p 210 text
27 Plate layout Use only straight 2 X4 or 2 X6 for plate material. Lay two pieces of the same length along the area being constructed. Caution; do not construct a wall any longer than can be easily lifted in to place.
28 Steps to laying out plates 1. Align both the top and bottom plate together and mark the location of all the studs. 2. Check the architectural plan and mark the center location of all windows and doors. 3. Mark off one half of the rough opening on either side of the center line. To the outside of these, mark the location of the trimmer and outside stud. Mark the trimmer with a T and the stud with an X.
29 Steps to laying out plates 4. Mark all the stud spaces between the two trimmers with a C, this designates them as crippled studs. 5. Layout the center line of intersecting partitions and where they will but. Add full length studs or blocking depending on method used.
30 Fig 9-12 p211 text
31 Story Pole A story pole is a long measuring stick made up by the carpenter on the job. It represents the actual height of the wall and contains information about header height and sill locations for all windows.
32 Fig 9-13 p221 text
33 Wall sections It is not uncommon for sheathing to be nailed in place before the wall is raised into place. Blocks may be nailed to the platform to prevent the wall from sliding off the platform when raised. Walls with no sheathing should have diagonal bracing to help hold the wall square. Be sure to have temporary bracing to hold the walls in place until securely fastened.
34 Partitions After all of the exterior walls, load bearing walls, and roof has been erected the partition can be installed. Partitions are the walls inside a house that divide off one room from another. Partitions are non load bearing walls and are not intended to carry any of the buildings load.
35 Partitions Cont. Non bearing partitions do not require any headers above door openings. Partitions are most often constructed using 2 X4 lumber. Studs are space at 16 o.c. Rough door openings are generally made 2 ½ wider than the finished door size.
36 Knee walls Knee walls are constructed in a similar manner to other wall with the exception of their height. A knee wall is usually about 4 in height but it depends on the construction. They are common in split level construction.
Chapter 23. Garage Construction
Chapter 23. Garage Construction 23.1 ESTABLISHING CHALK LINES 23.2 MEASURING AND CUTTING WALL PLATES 23.3 MARKING WINDOW & DOOR LOCATIONS ON EXTERIOR WALL PLATES 23.4 MARKING STUDS ON EXTERIOR WALL PLATES
More informationWall and Ceiling Framing
Student Edition Developed by the Curriculum and Instructional Materials Center for the Trade and Industrial Education Division Oklahoma Department of Career and Technology Education 00-00000 TI3674 Copyright
More information2x6. 2x8. 2x10. Size. 2-2x10 8'-5" w/ 2 NJ 7'-3" w/ 2 NJ
1 Rafter Size Spacing Allowable span 24" 11'-9" 24" 2x6 14'-1" 2x4 12" 15'-6" 12" 24" 14'-10" 24" 2x8 18'-2" 2x6 12" 20'-5" 12" 24" 18'-2" 24" 2x10 22'-3" 2x8 12" 25'-8" 12" 24" 21'-0" 24" 2x12 25'-9"
More informationBritish Columbia Carpenter Apprenticeship Program
British Columbia Carpenter Apprenticeship Program Level 3 Line H Competency H-7 Build Intersecting Roofs 7960003573 Ordering Crown Publications, Queen s Printer PO Box 9452 Stn Prov Govt 563 Superior St.
More informationChapter 6 - Walls & Stairs
Chapter 6 - Walls & Stairs Contents Chapter 6 - Walls & Stairs... 6-1 Timing & Prerequisites... 6-3 Wall Panel Components... 6-5 Headers... 6-7 Box Headers... 6-7 Solid Wood Headers... 6-8 Non-Load Bearing
More informationBuild a Wall Mockup. Description. Lesson Outcomes. Assumptions. Terminology. Carpenter
Description All walls in a house must be built to correct specifications and size in order to meet building code requirements. In this Activity Plan, students will build mock wall sections, with 48" (1200
More informationChapter 3. Wall Layout
Chapter 3. Wall Layout 3.1 LAYING OUT EXTERIOR WALLS 3.2 CUTTING EXTERIOR WALL PLATES 3.3 MARKING WINDOW AND DOOR LOCATIONS ON EXTERIOR WALL PLATES 3.4 MARKING STUDS ON EXTERIOR WALL PLATES 3.5 LAYING
More informationBuild a Full Height Wall
Youth Explore Trades Skills Description Standard wall sections are an important feature in residential house construction, and their components must conform to building code specifications. In this lesson,
More informationChapter 3. Wall Layout
GFCAHFH March 15, 2018 Construction Manual Version 18.0 Chapter 3. Wall Layout 3.1 LAYING OUT EXTERIOR WALLS 3.2 CUTTING EXTERIOR WALL PLATES 3.3 MARKING WINDOW AND DOOR LOCATIONS ON EXTERIOR WALL PLATES
More informationWall Framing & Sheathing
16 Wall Framing & Sheathing Section 16.1 Wall-Framing Materials Section 16.2 Wall Layout Section 16.3 Assembling & Erecting Walls Section 16.4 Special Framing Details Chapter Objectives After completing
More informationE-Z BUILD STEEL BARN 12' 12' 12' 16' 12' 20'
E-Z BUILD STEEL BARN 12' 12' 12' 16' 12' 20' BUILD You can construct your own E-Z frame barn with the help of this step by step guide. North American softwood dimensional lumber sizes: Nominal Actual in
More informationExperienced Worker Assessment Blueprint Carpentry
Blueprint Carpentry Test Code: 0207 / Version: 01 Specific Competencies and Skills Tested in this Assessment: Hand Tools Use and maintain fastening and prying tools Use and maintain sawing and cutting
More informationEntry Level Assessment Blueprint Carpentry
Entry Level Assessment Blueprint Test Code: 4115 / Version: 01 Specific Competencies and Skills Tested in this Assessment: Safety Demonstrate safe material handling practices Display comprehension of workplace/job-site
More informationE-Z BUILD SHED BUILDING GUIDE 10' 10' 10' 12' 10' 14' 10' 16' 10' 20'
E-Z BUILD SHED BUILDING GUIDE 12' 14' 16' 20' North American softwood dimensional lumber sizes: NOMINAL in in 1 4 1 6 2 4 2 6 ACTUAL in in ¾ 3½ ¾ 5½ 1½ 3½ 1½ 5½ Shown with rollup door Construct your own
More informationFraming Tech 1
Western Technical College 31410366 Framing Tech 1 Course Outcome Summary Course Information Description Career Cluster Instructional Level Total Credits 3.00 Total Hours 108.00 This course introduces the
More informationFastener Schedule. a, b, c. FASTENER Roof 3-8d (2 1 / ) / ) 3-10d. 3-10d ( ) 3-16d box nails. (3 1 2 toe nails on one side
ITEM 1 DESCRIPTION OF BUILDING ELEMENTS Blocking between joists or rafters to top plate, toe 2 Ceiling joists to plate, toe 3 4 5 6 Ceiling joists not attached to parallel rafter, laps over partitions,
More informationBUILDING THE BASIC SHED. Step A: Build the Foundation & Floor Frame
BUILDING THE BASIC SHED Step A: Build the Foundation & Floor Frame 1. Excavate the building site and add a 4" layer of compactible gravel. If desired, add an extension to the base for the optional wood
More informationWith Illustrations, Blueprints & Step By Step Details Brought To You By ShedPlansz.Com Click Here To Get More Shed Plans
12 X 8 Shed Plans With Illustrations, Blueprints & Step By Step Details Brought To You By ShedPlansz.Com Click Here To Get More Shed Plans Blueprints And Diagrams Instructions For Building The Shed
More informationMAT106: Wall Framing. AMERICAN FOREST & PAPER ASSOCIATION American Wood Council Engineered and Traditional Wood Products
MAT106: This portion of the program will address the code requirements for wall framing, although we won t address bracing in this section. The program contains a separate bracing section. 1 FASTEN PLATES
More informationSTATEWIDE CAREER/TECHNICAL EDUCATION COURSE ARTICULATION REVIEW MINUTES
STATEWIDE CAREER/TECHNICAL EDUCATION COURSE ARTICULATION REVIEW MINUTES Articulation Agreement Identifier: BUC 110 (2007-1) Identifier is the postsecondary course prefix followed by Plan-of- Instruction
More informationSections & Details VOCABULARY
1 Sections & Details VOCABULARY 1 ROOF FRAMING DETAIL RIDGE BOARD SHEATHING SHINGLES WEB FASCIA RAFTER (chord) SOFFIT SHEATHING STUD INSULATION DOUBLE TOP PLATE CEILING JOIST 2 FOUNDATION DETAIL STUD SHEATHING
More informationWith Illustrations, Drawings & Step By Step Details. Click Here To Download 12,000 Shed Plans. 1 P a g e Download 12,000 More Shed Plans
With Illustrations, Drawings & Step By Step Details Click Here To Download 12,000 Shed Plans 1 P a g e Download 12,000 More Shed Plans Table of Contents OVERVIEW... 3 MATERIALS & CUTTING LISTS... 4 DRAWINGS,
More informationMaterials. Description Quantity/Size Material Foundation Drainage material. 1.4 cu. yd. Compactible gravel
This 8 12-ft. shed features a simple gable roof, double doors, and side and rear windows for natural lighting. With full-height walls and doors, there's ample room for storing large items or creating a
More informationHOW TO BUILD A 12X8 SHED
HOW TO BUILD A 12X8 SHED With Illustrations, Drawings & Step By Step Details Note: This is a sample plan from RyanShedPlans. All other plans in our collection goes indepth with more details, more instructions,
More informationWith Illustrations, Drawings & Step By Step Details. Click Here To Download 12,000 Shed Plans. 1 P a g e H O W B U I L D S H E D.
With Illustrations, Drawings & Step By Step Details Click Here To Download 12,000 Shed Plans 1 P a g e H O W B U I L D S H E D. C O M Table of Contents OVERVIEW... 3 MATERIALS & CUTTING LISTS... 4 DRAWINGS,
More informationHowtoPlans..org. Luxe 12'x6' Garden Shed Plan
HowtoPlans.org Luxe 12'x6' Garden Shed Plan Compare our Free vs. Premium Shed Plan This perfectly designed plan will guide you through the entire process of building your very own shed for any backyard
More informationInstalling Novi Siding Trim
Installing Novi Siding Trim CAUTION: Remember that polymer undergoes expansion/contraction due to variations in temperature. The following instructions will allow for the expansion/contraction of the material.
More informationEntry Level Assessment Blueprint Carpentry
Entry Level Assessment Blueprint Carpentry Test Code: 4215 / Version: 01 Specific Competencies and Skills Tested in this Assessment: Safety Demonstrate safe material handling practices Display comprehension
More information4. Components and Stairs
4. Components and Stairs 4.1 BUILDING WINDOW AND DOOR COMPONENTS 4.2 BUILDING STAIRS Tools needed by volunteer: Hammer Nail apron Tape measure Square Utility knife Pencil Tools and equipment needed: Materials
More informationCore Curriculum Carpentry 1 Carpentry 2 Carpentry 3
A Correlation of Core Curriculum Carpentry 1 Carpentry 3 To the Carpentry II Course Standards and Objectives to the Content Standards Resource Title: Core Curriculum: Introductory Craft Skills, Fifth Edition
More informationGrand Garden Chalet 6X3 Assembly Manual
Revision #11 June 15, 2010 Grand Garden Chalet 6X3 Assembly Manual Thank you for purchasing a Grand Garden Chalet. Please take the time to identify all the parts prior to assembly. Please use Safety Eyewear
More informationFeaturing TJ Rim Board and TimberStrand LSL
#TJ-8000 SPECIFIER S GUIDE TRUS JOIST RIM BOARD Featuring TJ Rim Board and TimberStrand LSL Multiple thicknesses, grades, and products to cover all your rim board needs 1¼" Thickness matches lateral load
More informationHow-To-build guide Garden shed
How-To-build guide Garden shed What you can build using this guide This guide will show you how to build a re-locatable garden shed. Before you begin building Contact your local territorial authority to
More informationChapter 7 - Porch Framing
Chapter 7 - Porch Framing Contents Chapter 7 - Porch Framing... 7-1 Timing & Prerequisites... 7-2 Concrete Porches Caps (Contractor)... 7-3 Organize the Porch Framing Lumber... 7-3 Types of Porch Roofs...
More informationAcademic Plan Building Construction 2
Academic Plan Building Construction 2 Orientation to the Trade PACING: 3 weeks Unit Number: 1 Construction lab/ shop rules. Safety Contract Tool usage procedures. 1. Describe the history of the carpentry
More informationGarage Design Guide. October 2018
Garage Design Guide October 2018 The Corporation of the Township of Hamilton 8235 Majestic Hills Drive, P.O. Box 1060, Cobourg Ontario K9A 4W5 Tel: 905-342-2810 Fax: 905-342-2818 Email: Tim Jeronimus (Chief
More informationStrands & Standards CARPENTRY 2
Strands & Standards CARPENTRY 2 COURSE DESCRIPTION This is the second in a sequence of courses that prepares individuals to layout, fabricate, erect, install, and repair wooden structures and fixtures
More informationFine Homebuilding. Cottage Shed Plans
Fine Homebuilding Cottage Shed Plans 1 Front Elevation Designed with a cottage look, this small shed has clapboard siding on the front, a double door, a ramp to allow access for motorized yard equipment,
More information2.9 WINDOW & DOOR BUCKS
2.9 WINDOW & DOOR BUCKS Bucks provide attachment surfaces for windows and doors while holding back concrete from these openings during concrete placement. Mark the center and edges of openings as you place
More informationChapter 22. Shed Construction
Chapter 22. Shed Construction 22.1 BUILDING SHED FLOOR 22.2 BUILDING SHED WALLS 22.3 BUILDING SHED ROOF 22.4 ASSEMBLING SHED Tools needed by volunteers: Hammer Nail apron Tape measure Square Utility knife
More informationLESSON 1: UNDERSTANDING CONSTRUCTION DRAWINGS
LESSON 1: UNDERSTANDING CONSTRUCTION DRAWINGS INTRODUCTION In this lesson, you ll learn about the different types of drawings used in the construction industry, and how to read floor plans, section drawings,
More information3. Are component and cladding design pressures consistent with ASCE 7 for the wind speed and exposure category (ASCE 7 Fig. 6-3)?
Mobile County Public Works Residential Plan Reviewers Checklist For Structural Requirements of Wood Framed Residences Recommendation: Permit as Noted Revise Plans and Resubmit MCPW Ref. No. Design Criteria:
More informationFASTENERS BUILDING DEPARTMENT
FASTENERS BUILDING DEPARTMENT 952-446-1660 WWW.CITYOFMINNETRISTA.COM This handout is intended only as a guide and is based in part on the 2015 Minnesota Residential Code, Minnetrista City ordinances, and
More informationInstallation Instructions
Installation Instructions As with most building projects there's more than one way to build your storage building. But after building literally hundreds of them I believe I have figured out the easiest
More informationRafter Cutting Basics
Rafter Cutting Basics Understanding basic rafter principles is key to efficiently framing even the most complex roofs There are many ways to cut rafters. In more than 25 years of framing houses, I have
More informationCarpentry/Carpenter CIP Task Grid
1 Secondary Task List 100 SAFETY/OCCUPATIONAL ORIENTATION 101 Identify and follow all basic safety practices and procedures. 102 Identify and follow all lab safety practices and procedures. 103 Identify
More informationDescription. Lesson Outcomes. Assumptions. Build a Floor. Carpenter
Carpenter Description Floors are an integral part of residential construction and must be built to specifications that meet building code requirements. In this Activity Plan, students will be cutting and
More information4' x 12' Walk-In Chicken Coop Plan. Designed for 3-5 chickens
4' x 12' Walk-In Chicken Coop Plan Designed for 3-5 chickens Disclaimer The information provided here will show you how to build a chicken coop. However, we at howtoplans.org do not claim that the recommended
More informationHowtoPlans..org. 14'x8' Garden Shed Plan
HowtoPlans.org 14'x8' Garden Shed Plan Disclaimer The information provided here will show you how to build a shed. However, howtoplans.org does not claim that the recommended techniques are the only way
More informationWood structures Copyright G G Schierle, press Esc to end, for next, for previous slide 1
Wood structures Copyright G G Schierle, 2001-02 press Esc to end, for next, for previous slide 1 Wood Types: Balloon framing (rare) Platform framing Heavy timber framing Advantages: The only renewable
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised November 20, 2013 the Easton - R 12'x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationPRE-ENGINEERED HORSE STALL SYSTEMS SDFD SLIDING DOOR c/w FOLD-DOWN GRILL. & Assembly. Installation Instructions
PRE-ENGINEERED HORSE STALL SYSTEMS 4800 SDFD SLIDING DOOR c/w FOLD-DOWN GRILL & Assembly Installation Instructions 4800 SDFD Sliding Door c/w Fold-Down Grill Components - 1 3 /4" x 2" x 88" channels (2)
More informationBest Barns USA. Assembly Book. 12'x 16' the Millcreek. Revised September 19, 2017
Assembly Book Best Barns USA Revised September 19, 2017 the Millcreek 12'x 16' Manufactured by Reynolds Building Systems, Inc 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted Under the
More informationEZ Shed. Tool eeded ST MER SER I E
00 EZ Shed PLEASE READ ALL INSTRUCTIONS AND HELPFUL HINTS CAREFULLY BEFORE CONSTRUCTION Tool eeded ST MER SER I E 203 591-9032 - 30-5 30 INSTRUCTIONS 1. Separate and stack all parts included in kit. STUD
More informationHowtoPlans..org. 6'x8' Storage Shed Plan
HowtoPlans.org 6'x8' Storage Shed Plan Disclaimer The information provided here will show you how to build a chicken coop. However, we at howtoplans.org do not claim that the recommended techniques are
More informationInstallation Instructions
Installation Instructions As with most building projects there's more than one way to build your storage building. But after building literally hundreds of them I believe I have figured out the easiest
More informationGrand Garden Chalet 6X3 Assembly Manual
Revision #8 November 1, 2009 Grand Garden Chalet 6X3 Assembly Manual Thank you for purchasing a Grand Garden Chalet. Please take the time to identify all the parts prior to assembly. Please use Safety
More informationRoof Assembly & Sheathing
19 Roof Assembly & Sheathing Section 19.1 Ridges Section 19.2 Roof Assembly Section 19.3 Special Framing Details Section 19.4 Rakes & Cornices Section 19.5 Roof Sheathing Chapter Objectives After completing
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised September 12, 2017 the Easton 12'x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive - Greenville, PA 16125 This manual is copyrighted. Under
More informationMach Wall Installation Instructions
Mach Wall Installation Instructions Planning the Job Since Mach Wall is an innovative product that accomplishes 3 tasks at the same time (frame, insulate and drywall) and it replaces traditional framing,
More informationIntegrity Polygon and Round Top Installation and Finishing Instructions
Integrity Polygon and Round Top Installation and Finishing Instructions 08/20/2004 70852 BEFORE YOU BEGIN IMPORTANT: Read these instructions thoroughly before beginning to install your Integrity Polygon
More informationGLOSSARY OF TERMS SECTION 8
GLOSSARY OF TERMS SECTION 8 Anchor Bolt Angle Base Plate Bay Blocking CCB Centerline Chord Cladding Clip Closure Strip An A-307 steel bolt embedded in the concrete footing to anchor the base plate of the
More informationVinyl Windows and Doors Manufactured by Pella Corporation
Vinyl Windows and Doors Manufactured by Pella Corporation Part Number: V981255 2009 Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR BOW WINDOWS WITHOUT HEAD AND SEAT BOARD
More informationJOIST DETAILS Plate nail, 16d (0.15" x 1 ") at 1 on-center Blocking panel: 1 1 8" TJ Rim Board, 1 1 TimberStrand SL or TJI joist Toe nail, 10d (0.11" x ") at on-center A1 CS BEAM DETAILS L1 eb stiffener
More informationTOLL FREE:(888) FAX:(941) ASSEMBLY of ProTEC CONCRETE STRUCTURAL INSULATED PANEL
ASSEMBLY of ProTEC CONCRETE STRUCTURAL INSULATED PANEL The ProTEC panels are manufactured with grooves on all four sides to accept the steel components. This grooving applies to the regular panel whose
More informationINSTALLATION INSTRUCTIONS for Wood Bay or Bow Windows with Nailing Fin or Exterior Trim (JII032)
for Wood Bay or Bow Windows with Nailing Fin or Exterior Trim (JII0) Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for wood and clad wood bay
More information8x8 Shed Plans and Building Guide
Page 1 Legal 2018 Zac Spade & Christopher D. Brown. All Rights Reserved For information about special discounts available for bulk purchases, sales promotions, fundraising and educational needs, contact
More informationGrand Garden Chalet 6X3 Assembly Manual - Costco
Revision #16 March 22nd, 2013 Grand Garden Chalet 6X3 Assembly Manual - Costco Thank you for purchasing a Grand Garden Chalet. Please take the time to identify all the parts prior to assembly. Please use
More information6x6 Shed Plans and Building Guide
Page 1 Legal 2018 Zac Spade & Christopher D. Brown. All Rights Reserved For information about special discounts available for bulk purchases, sales promotions, fundraising and educational needs, contact
More informationCarpentry. EXAM INFORMATION Items. Points. Prerequisites. Course Length. Career Cluster EXAM BLUEPRINT. 1- Materials, Fasteners & Adhesives 10%
EXAM INFORMATION Items 73 Points 73 Prerequisites NONE Course Length DESCRIPTION This is the first in a sequence of courses that prepares individuals to layout, fabricate, erect, install, and repair wooden
More informationCABINET INSTALLATION INSTRUCTIONS
CABINET INSTALLATION INSTRUCTIONS Please read these instructions through completely before beginning the installation. Thank you for choosing Plato Personalized Custom Cabinetry for your home. Your Plato
More informationCONSTRUCTION / HOUSING
CONSTRUCTION / HOUSING - PRINCE EDWARD ISLAND APPLIED MATHEMATICS 80A Table of Contents Construction/ Housing Reading a Tape Measure (Imperial)... - Using a Carpenter s Square... -5 Checking for Squareness
More informationBefore installation, check your local and state requirements for this type of install.
1 Remove Packaging & Inspect Your Patio Door Remove shipping materials such as corner covers or pads. 2 Inspect Rough Opening Verify that the width and height of the patio door are each 1/2" to 3/4" smaller
More informationRoof Framing. Student Edition
Student Edition Developed by the Curriculum and Instructional Materials Center for the Trade and Industrial Education Division Oklahoma Department of Career and Technology Education 00-00000 TI3673 Copyright
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised February 4, 2016 the Millcreek-R 12'x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationSteel Reinforced Joining Thank you for choosing Andersen. Please leave this guide with building owner.
Steel Reinforced Joining (Horizontal/Vertical) for Andersen 400 Series Woodwright & Tilt-Wash Double-Hung, Picture, and Transom Windows and 400 Series Double-Hung Half Circle and Flexiframe Specialty Windows
More information6X3 Patio Garden Shed Assembly Manual
Thank you for purchasing a 6x3 Patio Garden Shed. Please take the time to identify all the parts prior to assembly. Revision #4 July 6th, 2016 6X3 Patio Garden Shed Assembly Manual Please use Safety Eyewear
More informationExterior Wall Fastener Schedule
City of Republic Community Development Department Exterior Wall Fastener Schedule REVISION DATE: JANUARY 2017 Design and construction (2012 IRC Section R602.3): Exterior walls of wood frame construction
More informationAssessment Blueprint
Assessment Blueprint Carpentry Basic 8326- Online Version 8327- Paper/Pencil Version Copyright 2009. All Rights Reserved. General Assessment Information Home Builders Institute Carpentry Basic General
More information10x10 Shed Plans and Building Guide
Page 1 Legal 2018 Zac Spade & Christopher D. Brown. All Rights Reserved For information about special discounts available for bulk purchases, sales promotions, fundraising and educational needs, contact
More information6x6 Maximizer Storage Shed Assembly Manual Version #9 Feb 26th, 2015
6x6 Maximizer Storage Shed Assembly Manual Version #9 Feb 26th, 2015 Thank you for purchasing a 6x6 Maximizer Storage Shed. Please take the time to identify all the parts prior to assembly. Please Note-
More informationDave's Glossary of Construction Terms. by Dave Osborne (www.daveosborne.com)
Dave's Glossary of Construction Terms by Dave Osborne (www.daveosborne.com) 5/4" A thickness of decking material between 1 x 6 and 2 x 6. Although it is called 5/4 x 6, it is actually 1" thick and 5 1/2"
More informationHowtoPlans..org. 10'x16' Storage Shed Plan
HowtoPlans.org 10'x16' Storage Shed Plan Disclaimer The information provided here will show you how to build a chicken coop. However, we at howtoplans.org do not claim that the recommended techniques are
More informationBuilding Science. Design Issues. Design Issues. Advanced Framing. Stack Framing Concept. Advanced Framing. Use Less Stuff Better
SUPPLY CENTRAL RETURN WALL 1 TW3046 TW3046 TW3046 TW3046 3068 UP SUPPLY TW3046 TW3046 16Õ-2Ó * 19Õ-2Ó * 16Ó 16Ó 16Ó 16Ó Joseph Lstiburek, Ph.D., P.Eng Building Science Advanced Framing Use Less Stuff Better
More informationHowtoPlans..org. 8'x10' Storage Shed Plan
HowtoPlans.org 8'x10' Storage Shed Plan Disclaimer The information provided here will show you how to build a chicken coop. However, we at howtoplans.org do not claim that the recommended techniques are
More informationChapter 9. Windows and Exterior Doors
Chapter 9. Windows and Exterior Doors 9.1 INSTALLING WINDOWS 9.2 INSTALLING EXTERIOR HOUSE DOORS 9.3 INSTALLING SHED DOOR 9.4 INSTALLING EGRESS COMPONENTS Tools needed by volunteers: Hammer Nail apron
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised September 12, 2017 the Denver 12' x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted. Under the
More informationBC CARPENTER APPRENTICESHIP PROGRAM LEVEL (Harmonized)
BC CARPENTER APPRENTICESHIP PROGRAM LEVEL 2 2018 (Harmonized) Line H: Wood Frame Construction Competency H-4: Build Wall Systems 2017 Industry Training Authority of British Columbia This publication may
More informationReinforced 10 Bow Window Assembly and Installation Guide for Andersen 400 Series Transom Joined Casement Windows
Reinforced 10 Bow Window Assembly and Installation Guide for Andersen 400 Series Transom Joined Casement Windows Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction
More informationBUILDING PLANS. BUILDING DEPARTMENT
BUILDING PLANS BUILDING DEPARTMENT 952-446-1660 www.cityofminnetrista.com This handout is intended only as a guide and is based in part on the 2015 Minnesota Residential Code, Minnetrista City ordinances,
More informationHowtoPlans..org. 12'x20' Garden Shed Plan
HowtoPlans.org 12'x20' Garden Shed Plan Compare our Free vs. Premium Shed Plan This perfectly designed plan will guide you through the entire process of building your very own shed for any backyard or
More information3.1 General Provisions
WOOD FRAME CONSTRUCTION MANUAL 107 3.1 General Provisions 3.1.1 Prescriptive Requirements The provisions of this Chapter establish a specific set of resistance requirements for buildings meeting the scope
More informationSTATEWIDE CAREER/TECHNICAL EDUCATION COURSE ARTICULATION REVIEW MINUTES
STATEWIDE CAREER/TECHNICAL EDUCATION COURSE ARTICULATION REVIEW MINUTES Articulation Agreement Identifier: CAR 111 & CAR 114 (2006-1) Identifier is the postsecondary course prefix followed by Plan-of-
More informationHowtoPlans..org. 8'x12' Storage Shed Plan
HowtoPlans.org 8'x12' Storage Shed Plan Disclaimer The information provided here will show you how to build a chicken coop. However, we at howtoplans.org do not claim that the recommended techniques are
More informationSTACKING MULTI-SLIDE DOOR SYSTEM
SMSD STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION! CAUTION Lead-based paint may be present in older homes, and the removal
More informationGarden Chalet 4X2 Assembly Manual
Revision #6 April 12th, 2010 Garden Chalet 4X2 Assembly Manual Thank you for purchasing a 4x2 Garden Chalet. Please take the time to identify all the parts prior to assembly. Please use Safety Eyewear
More information12x12 Shed Plans and Building Guide
Page 1 Legal 2018 Zac Spade & Christopher D. Brown. All Rights Reserved For information about special discounts available for bulk purchases, sales promotions, fundraising and educational needs, contact
More informationChapter 17 - Porch Trim
Chapter 17 - Porch Trim Contents Chapter 17 - Porch Trim... 17-1 Timing & Prerequisites... 17-2 Trim on Porch Beams (Volunteer)... 17-4 Smart Trim on the Bottom of the Beam... 17-4 Smart Trim on the Inside
More informationWindow with Nail fin (New construction)
Window with Nail fin (New construction) Disclaimer: Improper installation and care may void warranty. These instructions are a basic/general recommendation for installation, but may not be utilized in
More information8x12 SpaceMaker Garden Shed Assembly Manual
8x12 SpaceMaker Garden Shed Assembly Manual Version #6 Revised June / 2007 Thank you for purchasing a 8x12 SpaceMaker Garden Shed. Please take the time to identify all the parts prior to assembly. Safety
More information