Using the star template provided, trace out half the star shape on the pegboard sheet. Flip template over and trace out other side of star.
|
|
- Lynette Grant
- 5 years ago
- Views:
Transcription
1 Shining Star PROJECT INFORMATION Created by DIY hacker, woodworker and teacher, Kerryn Carter of Toolschool, brighten up your Christmas with this shining Star, complete with LED lights for extra twinkle. DIFFICULTY: MEDIUM CATEGORY: HOLIDAY PROJECT Tools used: JIGSAW GLUE GUN DRILL DRIVER PALM SANDER Also used: RULER AND PENCIL CLAMPS 3MM DRILL BIT (PILOT HOLE) 1 Pencil it in Using the star template provided, trace out half the star shape on the pegboard sheet. Flip template over and trace out other side of star. TIP: For a little added flare, using spray paint, coat the smooth surface of the pegboard (we chose metallic silver for added sparkle). 4.5MM DRILL BIT (THROUGH HOLE) COUNTERSINK BIT (OPTIONAL) 10 X WOODSCREWS (6G X 20MM) 19MM DRESSED PINE (64MM X 1M) 7MM PLYWOOD (APPROX. 250MM X 250MM ) 4MM PEGBOARD (ROUGHLY 250MM X 250MM) CURTAIN STRING LIGHTS (APPROX100 LED BULBS) BATTERIES SPRAY PAINT (OPTIONAL)
2 2. Shining Star 2 Hold it down Clamp down pegboard to a stable and secure surface. Using the Ryobi ONE+ Jigsaw, follow your stencil line and cut out all sides. TIP: move the piece of wood around to suit you, turning and re-clamping as you go. The jigsaw should always be moving away from you, with your weight firmly holding down the tool. 3 Make the cut To cut the sides of the star, first set your Ryobi ONE+ Jigsaw to a 45 degree bevel angle. Clamp down lengths of 19mm dressed pine and cut length of wood so that the long side is 93mm in length. SIDE PROFILE 93mm 4 Keep it in line Better safe than sorry, check your first piece up against the side of the pegboard star to ensure it s the right size. The piece will be a little shorter than the side of the star as we need to allow room for the other pieces to slide in next to each other.. Repeat so you have 10 identical strips.
3 3. Shining Star 5 Smoother Operator Using your Ryobi ONE+ Palm Sander, smooth out any of the rough edges. 6 Hold it together Using the Ryobi ONE+ Glue Gun, glue the pine lengths to the star. The long side should be the side you stick to the edge of the pegboard. Repeat until all sides are complete. 7 Back it up So that you get an accurate backing plate, lay the star down on a sheet of 7mm ply and trace around the edges of the star. Using the Ryobi ONE+ Jigsaw, cut around your pencil outline. 8 Here s the drill Along each side of your star s backing plate, drill a hole using a 5mm drill bit and your Ryobi ONE+ Drill Driver. These holes should only be 4.5mm away from the edge.
4 4. Shining Star 9 Sink or swim (optional) Using a countersink bit, make holes in line with your pre-drilled holes. TIP: Countersinking the holes gives you a flush finish on the backing. If you don t have a countersink bit, this step can be skipped and you can just screw backing directly onto the star frame. 10 Shining Star Take the battery powered LED Curtain String Lights and insert each individual light into a pegboard hole. Before moving to the next step, make sure all lights are secure and won t fall out. 11 Close it up Place the backing plate onto the star frame, ensuring the Curtain String Light battery pack is left out. With your Ryobi ONE+ Drill Driver, drill a pilot hole of 3mm then screw the backing plate on securely with 10 x woodscrews.
5 5. Shining Star 12 You ve got the power! Using your Ryobi ONE+ Glue Gun, stick the LED Curtain String Light battery pack to the outside of the star s backing plate. 13 Tree Topper (optional) If you re making the Ryobi Christmas Tree and want to use this star as the tree topper, using 6mm drill bit, drill a hole into one of the angled sections of the star. This will then sit on the dowel piece you inserted into the tree s trunk (refer to Wooden Christmas Tree build guide). 14 Finish it off Put batteries in the Curtain String Lights, turn on, stand back and admire. You re the real superstar!
6 6. Shining Star Star (half)
Wooden Christmas Tree
Wooden Christmas Tree Created by DIY hacker, woodworker and teacher, Kerryn Carter of Toolschool, take your Christmas tree to a whole new level, with this wooden Christmas Tree project. PROJECT INFORMATION
More informationDIY RUSTIC HALL TREE
DIY RUSTIC HALL TREE *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever using power tools
More informationRobert Bosch GmbH. Wall organiser
Wall organiser The organisational talent Wall organiser Say goodbye to messiness! The wall organiser is the ideal place to store everything that tends to lie around. 1 Introduction Wardrobes, drawers and
More informationDIY Wine Storage Cabinet
DIY Wine Storage Cabinet ADDICTED2DIY.COM *Before beginning this project, please read through all of the plans and the blog post. When building this project, be sure to measure your wood and cut to fit.
More informationMyOutdoorPlans.com. By Julian King [2X4 GARDEN BENCH]
MyOutdoorPlans.com By Julian King [2X4 GARDEN BENCH] CUT LIST A 2 pieces of 2 4 lumber 24 long, 2 pieces 32 1/2 long LEGS B 2 pieces of 2 4 lumber 45 long, 2 pieces 15 1/2 long, 1 piece 12 1/2 long SEAT
More informationLARGE PLYWOOD CUTTING GUIDE
Copyright 2015 Shanty-2-Chic.com Workbench I f you are tight on space but large on ideas this bench is just what you need. Sturdy and mobile this bench has an ingenious fold out wing that gives you over
More informationRobert Bosch GmbH. Minimalist washstand
Minimalist washstand Neat and tidy Minimalist washstand Minimalist design in the bathroom is in fashion. And rightly so, as this washstand proves: because less is more! 1 Introduction Here s an idea to
More informationFLOW HIVE ASSEMBLY GUIDE. If we look after the bees they will look after us, and the honey really is an amazing bonus. Flow Hive Hybrid 3 Frame
AUSTRALIAN MADE If we look after the bees they will look after us, and the honey really is an amazing bonus. FLOW HIVE ASSEMBLY GUIDE Flow Hive Hybrid 3 Frame Read all instructions first. If you are unfamiliar
More informationDIY Outdoor Console Table Addicted2DIY.com
DIY Outdoor Console Table Addicted2DIY.com *Before beginning this project, please read through all of the plans. Always use safety precautions whenever using power tools and follow the manufacturer s suggested
More informationCOMPLIMENTARY WOODWORKING PLAN
COMPLIMENTARY WOODWORKING PLAN COFFEE TABLE PLAN This downloadable plan is copyrighted. Please do not share or redistribute this plan in any way. It has been paid for on your behalf by JET Tools, a division
More informationWanderlust Suitcase Vanity
Wanderlust Suitcase Vanity If you re like me, you re always up for an adventure. When I saw some examples of DIY reclaimed suitcases, paired with the exciting new Wanderlust embroidery design collection,
More informationDIY CHILD S STOOL. Instructions
DIY CHILD S STOOL Children have their own special world. And having the right furniture is part of that world. We have designed an easy-to-assemble child's stool that you can paint in a selection of bright
More informationThank you for purchasing these easel plans. I think you will find this to be a fun, easy to build project that will serve you for years to come.
Construction Plans for The Basic Wooden Easel Updated August, 2002 Thank you for purchasing these easel plans. I think you will find this to be a fun, easy to build project that will serve you for years
More informationWays to get the most out of your
5 Ways to get the most out of your router table When you mount a router on a table, you expand your shop s potential. To help you take advantage of this potential, we assembled five router table techniques
More informationDIY Bedroom Entertainment Center
DIY Bedroom Entertainment Center Free woodworking plans for building a bedroom entertainment center that also serves as a laundry sorter. Perfect for bedroom with limited wall space. Cost: ~$250 Difficulty:
More information15 Dovetail Jig. Instruction Manual. Part # 3452
15 Dovetail Jig Instruction Manual Part # 3452 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools. Peachtree Woodworking
More informationHinge Mortising Jig. One of the make it or break it parts of building a. 6 ShopNotes No. 74
Hinge Mortising Jig A Mortise for a Hinge. Quick, clean, and accurate that s the only way to describe the mortise you get with a trim router and this hinge mortising jig. One of the make it or break it
More informationEASY BREAD/ CUTTING BOARDS
PLANS BY DEEPLY SOUTHERN HOME EASY BREAD/ CUTTING BOARDS DIFFICULTY LEVEL: EASY TOOLS REQUIRED 18V ONE+ RANDOM ORBIT SANDER 18V ONE+ CORNER CAT FINISH SANDER 18V ONE+ LITHIUM-ION DRILL KIT 18V ONE+ ORBITAL
More informationBuild the Spitfire: Step-By-step. Pack 3 Stages 21-30
Pack Stages 2-0 Contents Stage Page Number 2 72-74 22 75-78 2 79-8 24 82-84 25 85-88 26 89-9 27 92-94 28 95-97 29 98-00 0 0-05 Editorial and design by Continuo Creative, 9-4 North Road, London N7 9DP All
More informationProject 17884EZ: Shaker End Table
Project 17884EZ: Shaker End Table With its clean, simple lines, this piece is unmistakably Shaker style. Ours is made from cherry, a wood commonly used by Shaker craftsman, but we ve also seen this piece
More informationAsk your DIY store or carpenter to cut the required boards to size. Instructions. 1. Cut out the opening for the bottles
KITCHEN TROLLEY Next time you're whipping up some magic in the kitchen, take advantage of our willing assistant. Fixed on rollers to provide easy mobility, our kitchen trolley can be stationed wherever
More informationforce Use the A lounge room makeover that s out of this world! With its iconic scenes Use the OCTOBER 2015
OCTOBER 2015 SEEN ON BHG TV BEFORE force A lounge room makeover that s out of this world! With its iconic scenes of galactic fantasy, Star Wars is one of cinema s most popular film series. Now you can
More informationWood Sawhorse. Description: Materials: Tools: Drawing/Photo: Name: Date:
Wood Sawhorse Name: Date: Description: The project is a wood sawhorse that can be used for workspace for future projects. It requires layout and wood working/construction skills. Materials: 4-1x6x30 DF
More informationDesigned by Melissa DiRenzo thesweetescape.ca
instructions Designed by Melissa DiRenzo thesweetescape.ca YOU WILL NEED 3 -diameter foam ball Christmas sweater Hot glue gun and glue sticks 3/8 -wide satin ribbon Elastic thread: metallic Note: A child
More informationThe easy way to an affordable kitchen
quality, affordable, pre-assembled The easy way to an affordable kitchen In association with All Insta-Cupboard carcass units are supplied pre-assembled to simplify installation Choose the colour of your
More informationBuild Instructions for Towers of Doom
Build Instructions for Towers of Doom 1. Measure and cut 4 x 8 sheet of plywood in half (or ask Home Depot to do it!). You will use one 4 x 4 sheet for the course base. 2. Attach a support frame to the
More informationTM TM DOG HOUSE Age 9+
TM TM DOG HOUSE Age 9+ Safety First! Use eye protection, always! Use ear protection with loud power tools Stay with kids while they work! Follow tool manufacturers safety guidelines This project is recommended
More informationJUNIOR CERTIFICATE 2005 MATERIALS TECHNOLOGY (WOOD) MARKING SCHEME ORDINARY LEVEL SECTION A
JUNIOR CERTIFICATE 2005 MATERIALS TECHNOLOGY (WOOD) MARKING SCHEME ORDINARY LEVEL SECTION A NOTE Please ensure that totals for each question are divided by two before entering marks on marking sheets.
More informationMLCS Instructions for Bowl and Tray Template Kit #9176/#9179
MLCS Instructions for Bowl and Tray Template Kit #9176/#9179 Tools Needed: Router 1-1/2 h.p. Minimum recommended with a 1/2 collet Forstner bit 3/4-2 recommended depending on template used Drill Press
More informationSeamed Undermount Bowls
CUTOUT TEMPLATES MAKING CUTOUT TEMPLATES 7.1 CUTOUT TEMPLATES The use of an accurate template is one of the most essential elements to the successful completion of a cutout in Corian. For the completion
More informationContents. Build the Spitfire: Step-By-step
Pack 2 Stages -20 Contents Stage Page Number 8-0 2 - - 7 8-50 5 5-5 6 5-57 7 58-60 8 6-6 9 6-67 20 68-7 Editorial and design by Continuo Creative, 9- North Road, London N7 9DP All rights reserved 20 De
More informationZiroli D-17 Beech Staggerwing
Ziroli D-17 Beech Staggerwing Parts List Vacuform Parts: Miscellanous Pieces 1 Four Side Panels 1 3/16" Tube, 2" Long 2 Lower Dash - Back Dash 2 Felt, 12x24 3 Dash 3 Cordury 12x24 4 Dash Hood 4 Aluminum
More informationExtendable Large Dovetail Jig
Extendable Large Dovetail Jig Instruction Manual Part # 3458 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools.
More informationWOOD TOY NEWS. July 23, 2013 Tuesday
WOOD TOY NEWS Make your own perfect turntable for spray painting toys with these useful tips. And it s fast, fun and easy to build! by Imants Udris Watch the video on our website at : http://www.toymakingplans.com/website/how-to/
More informationPachinko Machine. Supplies: Part One: Construction. Optional: (1) 21" x 15.5" piece of wood. jumbo craft sticks. (2) 17" x 1" pieces of wood
Supplies: (1) 21" x 15.5" piece of wood jumbo craft sticks (2) 17" x 1" pieces of wood standard craft sticks (2) 14.5" x 1" pieces of wood 1" wooden craft circles (2) 4" x 2" pieces of wood drill (1) 14.5
More informationRosalina Accessories Tutorial Version March 2011 Martyn
Rosalina Accessories Tutorial Version 1.0 - March 2011 Martyn Star Brooch Feel free to experiment with these dimensions, you should make a template you are happy with, the method still works. 1) Creating
More informationDIY Farmhouse Cabinet
DIY Farmhouse Cabinet Addicted2DIY.com *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever
More informationPROJECT PLANS WOODEN GIFT BOX
PROJECT PLANS WOODEN GIFT BOX Make the gifts you give even more special by presenting them in this one-of-a-kind gift box. In fact, the box may be valued more than whatever it contains. The box is sized
More informationINSTRUCTIONS for fire lamps 1-8
INSTRUCTIONS for fire lamps 1-8 1. Lamp from wooden pen holder: Material used: Article Number Quantity:: Pendant lamp holder, 100cm lamp cable with ceiling rose and pendant lamp holder 116013 1 Wooden
More informationWelcome to our Wee Work section that will provide you and your. child with a learning activity that will engage their senses and
Welcome to our Wee Work section that will provide you and your child with a learning activity that will engage their senses and emerging skills. Scroll down the page to find the activity that meets your
More informationThis indicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
S i m p le Woodworking: What You'll Need v lumber 2-1 x 12 x 6 hardware/supplies (availability will vary) 1 1/4" pocket hole screws #18 x 1 1/2 brads or pocket hole plugs 12-inch continuous hinge magnetic
More informationwoodworkersjournal.com MATERIAL LIST
MATERIAL LIST T x W x L 1 Legs (2) 1 1 2" x 3 1 2" x 36 7 16" 2 End Uprights (2) 1 1 2" x 3 1 2" x 32 1 2" 3 Stringers (4) 1 1 2" x 3 1 2" x 42" 4 Top Cladding, Long (2) 3/4" x 7 1 4" x 65 3 4" 5 Side
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 1
Kentucky 4H Wood Science Plans Notebook Plans Level 1 MATERIALS NEEDED: 1 piece wood 3/4" x 2 x 2 1 piece wood 3/4" x 3 x 3 1/2" 1 wooden spring-type clothespin 2-1 1/2" nails 1-1/2 woodscrew Wood Glue
More informationPoorBoy Skiff. A 10-11ft 6in skiff for outboard motoring By Steven Lewis
PoorBoy Skiff. A 10-11ft 6in skiff for outboard motoring By Steven Lewis PoorBoy is about the simplest small motorboat you will come across. It consists of 2-2 1/4 sheets of plywood (1-1 1/4 sheets x3/8
More informationTOOLS 2 ½ hole saw (a good sharp one. You re going to make 36 holes.) Sharp pencil Yard stick Compass Protractor Sandpaper Rasp Drill Motor Jig Saw
My version of this upright rifle rack does not have a turntable or lazy Suzan on it. I need to be able to move my rifles around so I opted to put casters on the bottom of the rack. With four casters, it
More informationCopyright 2010 Springbok Publishing All Rights Reserved- Page 1
Copyright 2010 Springbok Publishing All Rights Reserved- www.woodensaddlerackplans.com Page 1 Legal Information All contents copyright 2010 by Springbok Publishing. All rights reserved. No part of this
More informationC & C 30 MK II % Cockpit Seat Backrests. Installed on S\V "Wyndisphree" S/N 58 86E18806 (03/23/2000)
C & C 30 MK II % Cockpit Seat Backrests Installed on S\V "Wyndisphree" S/N 58 86E18806 (03/23/2000) C & C 30 MK II Building the Removable Seat Backrests 1. This package contains instructions and sketches.
More informationCedar 2-Drawer Desktop Storage Cube
Cedar 2-Drawer Desktop Storage Cube 5 ½ Dimensions 5 ½ 5 ½ 2 2 1 7/8 4 ¼ 4 ½ Author s Notes: Build a Cedar 2-Drawer Desktop Storage Cube from just 1 cedar fence picket. No angles, special cuts or rips
More informationBUILDING A TREE BENCH
INSTRUCTIONS FOR A In just a few steps, we show you how to build your own tree bench and paint it perfectly. 1 SIDE PIECES OF THE SEATING SURFACE Purchase the materials from the enclosed list. Draw a 10
More informationBuild the Spitfire: Step-By-step. Pack 7 Stages 61-71
Pack 7 Stages 61-71 1 Stage Contents Page Number 61 212-215 62 216-218 63 219-221 64 222-224 65 225-228 66 229-231 67 232-235 68 236-238 69 239-241 70 242-245 71 246-249 Editorial and design by Continuo
More informationPage 1 C & C 30 MK II. Building the bulkhead Liquor Cabinet. 1. This package contains pages of instructions and sketches.
Page 1 C & C 30 MK II Building the bulkhead Liquor Cabinet 1. This package contains pages of instructions and sketches. 2. Woodworking skills and equipment are essential to make the 33 pieces and assemble
More informationOffice Towers 83 ¼ 35 ½ 18 ¼
Copyright 2015 Shanty-2-Chic.com T Office Towers his towering hutch will be admired for years to come. Inspired by rustic, high end furniture found in boutique showrooms it will impress all who see it...especially
More informationShop-Made Miter Clamps
*Editor s note: In the photos showing the table saw, the blade guard has been removed for clarity. I try to be as self-sufficient as possible, so I like to manufacture my own tools whenever I can. I designed
More informationPrimary STEaM Progression & Scheme of Work Using Crumble Control Board & Accessories (Page 1) (1st Draft)
Primary STEaM Progression & Scheme of Work Using Crumble Control Board & Accessories (Page 1) (1st Draft) Chapter 2 Lights, Lights, Lights Add programmable light(s) to a pupil created picture Curriculum
More informationSmall 45 Roof Houses 1 or 2 Story 1 /24 th Scale Patterns
BA GARDEN TOWNS 45 Roof Houses 10" x 10" 1 or Story Scaled and easy to read patterns and instructions for wood houses. Yard and Garden Buildings Compatible with Garden Railroads or a delight for any child's
More informationPhase Two. The Skirt, Play Area and Sub Table ( continued )
Dry fit the skirt in place and make sure all is tight. Drill a countersink screw hole on the back of the skirt down where you will connect it to the bull nose. Make three holes on each board (ends and
More information10. Wing prep and subassembly
Date Section Objective: Construct and fabricate the sub-assemblies of the wing panel. Required Parts: Wing left 11gal PN104-300, Wing right 1gal PN104-400, Wing left 15 gal option PN104-322, Wing right
More informationMark out the centre lines of the cross plates on the side plates and drill small holes for panel pins, 3 or 4 should do, use a drill smaller than the
Powder Bins The design is for A5, with 10mm all round to aid part removal, with a part height of approx 180mm, this gives a machine that can produce a reasonable sized part without being to large. The
More informationDIY Rustic Dresser Addicted2DIY.com
DIY Rustic Dresser Addicted2DIY.com *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever using
More informationContest Field Border Construction Manual
Contest Field Border Construction Manual TABLE OF CONTENTS Section 1 Field Construction...3 Section 2 Bill of Materials 3 Section 3 Construction.. 4 Step 1 - Layout...4 Step 2 - Bottom...4 Step 3 1 st
More informationADULT. Adirondack / Muskoka Chair Plans
ADULT Adirondack / Muskoka Chair Plans Materials List 3/4" x 9 1/2" (1.9cm x 24.1cm) redwood, cedar or pine boards. Six, 8' (2.44m) boards should make one chair depending on knots and layout. You can also
More informationMaking Simple Bookbinding Equipment
Tony Firman 20 1 2 19 Notes Tony Firman Tony Firman Bookbinding 18 3 : 2012 Tony Firman Bookbinding P.O. Box 507 Haslet, TX 76052 www.tonyfirmanbookbinding.com 4. When all the tapes have been pinned in
More informationProject 19496EZ: Rocking Horse. Rocking Horse Materials List
Project 19496EZ: Rocking Horse A delightful must gift for preschoolers, our rocking horse is made from sturdy stock like maple or birch. Easy to build with optional detailing: if you don t want to paint
More informationContents. pages 20-24: Installing Edge sinks into. custom laminate countertops page 8: Installing Edge sinks into postform laminate countertops
Contents pages 2-8: Installing Edge sinks into custom laminate countertops page 8: Installing Edge sinks into postform laminate countertops pages 9-14: Installing Acrylic sinks into custom laminate countertops
More informationImportant Note: Why this guidebook is FREE?
Easy DIY Murphy Bed Construction Guide 1 Important Note: This guide is a FREE SAMPLE of our Complete Construction Guidebook. With the help of this guide you will get familiar with the construction steps
More informationBuild your own Drawer unit. D3 / D4
Page1 Build your own Drawer unit. D3 / D4 1: Introduction. This guide will give you the plans, materials and how to information to build your own drawer unit. The dimensions given will fit a D3 or D4,
More informationGarden Bridge. c D E. All dimensions are in mm- Arch Tread Handrail' Post Reinforcement brace. Written & designed by David Watkins.
Garden Bridge Written & designed by David Watkins Slmple by design yet decorative by nature. This ornate Garden Bridge will rest proudly amongst most garden backdrops. The fiddliest step in this project
More informationRobert Bosch GmbH. Lounge light fixture
Lounge light fixture Nice and relaxing Lounge light fixture Light has an important effect on mood. This cool light fixture is perfect for creating a cosy lounge atmosphere. 1 Introduction This cool light
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 2
Kentucky 4H Wood Science Plans Notebook Plans Level 2 MATERIALS NEEDED: JEWELRY BOX WS201 1 piece wood 1/4" x 4 x 4 1/2" (bottom) 1 piece wood 1/4" x 4 1/2" x 5 (top) 2 pieces wood 1/4" x 2 x 5 (front
More informationThis book, or portions of it, may not be duplicated, resold, or redistributed in any way, without the expressed written consent of Stay Tooned, Inc.
Copyright 2006 - Stay Tooned, Inc. All rights reserved worldwide. This book, or portions of it, may not be duplicated, resold, or redistributed in any way, without the expressed written consent of Stay
More informationSmall Town Buildings. Scaled and easy to read patterns and instructions. Shoe / Western Union (with and without porch)
1 /24 th Scale Patterns kiva design G R O U P E 1 Story Flat Roof Yard and Garden Buildings Compatible with Garden Railroads or a delight for any child's collection Overall Dimensions Foundation: 10" x
More informationuin RC FPRC ZERO Specificationss Empty Weight
Flying Pengu uin RC FPRC ZERO Specificationss Wing Span 42.75 (1085 mm) Fuselage length 30.5 ( 775 mm) Empty Weight 9.5 10 oz. (150 160g) Estimated Flying Weight 20 255 oz. (320 400g) Wing Area: 151 sq.
More informationRouter Table. In a recent article, I wrote about the router table I built for the Center. 5 Essential Jigs for the
5 Essential Jigs for the Router Table Great fixtures and fences offer better control and new possibilities BY PETER SCHLEBECKER In a recent article, I wrote about the router table I built for the Center
More informationPROJECT PLANS EXPANDABLE CRAFT CENTER
R PROJECT PLANS EXPANDABLE CRAFT CENTER Whether you re working on craft projects, sewing, or pursuing another hobby, this craft center offers a great place to work. It features a large work surface that
More informationHow to Build a DIY Extra Long Wood Bench
How to Build a DIY Extra Long Wood Bench Free woodworking plans for building a large, extra-long wood bench. This bench measures 9 in length and is designed to match the DIY Large Outdoor Dining Table,
More informationWind Turbine Experimenter s Kit User Guide
Wind Turbine Experimenter s Kit User Guide 42284 V0116 Cautionary and Warning Statements This kit is designed and intended for educational purposes only. Use only under the direct supervision of an adult
More information3Insert the second rod no. 4
Yamato: Step-by-step 37 The stern block and searchlight control towers a b c d e f Recommended tools and materials Wood glue Sandpaper (no. 800 grain) Metal file Putty Craft knife For metal: Super Glue
More informationCockpit Kit. Full Depth - Builds Quickly - Light Weight READ THROUGH THIS INSTRUCTION MANUAL FIRST. IT CONTAINS IM- laser cut wood kit
The Savage Light Sukhoi Su- 27 Cockpit Kit contains everything you need to build a full depth semi scale Su-27 cockpit, yet adds less than an ounce to your finished model s weight (not including pilot).
More informationClock 35 - Toyland. Construction instructions for Clock 35
This clock has been designed for children, it is a stand-alone unit and can be positioned on a shelf or cabinet out of the reach of very young hands who may be tempted to touch. The clock is shown in two
More informationleaf table Leaves dropped, this traditional oak table makes an ideal kitchen island. Leaves extended, it s a small breakfast table
leaf table Leaves dropped, this traditional oak table makes an ideal kitchen island. Leaves extended, it s a small breakfast table The drop-leaf table is a traditional favourite, but the one I ve designed
More informationChapter Four, Fitting out the Shell
Chapter Four Fitting out the Shell This chapter outlines the process for fitting the parts that go into a round or stave back shell. Square back sound boxes usually have the cap and base of the sound box
More informationWhy are we giving this guidebook as a FREE download?
Construction Guide Queen, Double & Twin Vertical 1 Note: This guide covers the construction steps for all 3 sizes of the vertical wall mount Easy DIY Murphy beds, Queen, Double and Twin. The construction
More informationIF INSTALLING ANY OF THE PORTMAN SELF CLOSING SYSTEMS, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS SUPPLIED WITH THE CLOSING SYSTEM FIRST
Set A Set B PFD60 Fire Door Kit FITTING INSTRUCTIONS IF INSTALLING ANY OF THE PORTMAN SELF CLOSING SYSTEMS, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS SUPPLIED WITH THE CLOSING SYSTEM FIRST SUGGESTED
More informationHM OUTDOOR TABLE:HM OUTDOOR TABLE 25/7/08 11:18 AM Page 30
HM080827 OUTDOOR TABLE:HM080827 OUTDOOR TABLE 25/7/08 11:18 AM Page 30 The treated-pine frames of the table and benches are topped with sturdy blackbutt timber. HM080827 OUTDOOR TABLE:HM080827 OUTDOOR
More informationProject Skill Level: INTERMEDIATE Plywood Used: CANPLY EXTERIOR Good Two Sides (G2S) or precision sanded Aspen
Project Skill Level: INTERMEDIATE Plywood Used: CANPLY EXTERIOR Good Two Sides (G2S) or precision sanded Aspen MATERIALS LIST: (1) ¾" x 4 ft x 8 ft plywood panel (20) #8 x 2" Robertson or Phillips wood
More informationKitchen Base Cabinet: Multiple Drawers Cabinets from Scratch
Kitchen Base Cabinet: Multiple Drawers by Cabinets from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for any loss, damage,
More informationCactus Routed Bowl. MLCS Items Needed:
Cactus Routed Bowl MLCS Items Needed: Cactus Bowl and Tray Template #9188 Top Mounted Bearing Dish Cutter Router Bit #7817 1/2 Router Collet Extension and Wrenches #9465 45* Degree Chamfer Bit #7676 1-3/8
More informationAdjustable Hammered Dulcimer Stand
Adjustable Hammered Dulcimer Stand Musicmaker s Kits (Hwy 36 behind Joseph s Restaurant) P.O. Box 2117 Stillwater MN 55082 651 439 9120 www.harpkit.com PARTS LIST: 1 Set of Assembly Instructions A. 2 front
More informationCoffee table with recessed tray
Coffee table with recessed tray Dinner is served Coffee table with recessed tray This coffee table has it all: it contains a recessed tray, so that you can treat your guests to various delicacies. 1 Introduction
More informationMUTINEER AND BUCCANEER TOP-MOUNTED CENTERBOARD HANGERS. Note, drawing not to scale Bob DeRoeck May 31, 05
MUTINEER AND BUCCANEER TOP-MOUNTED CENTERBOARD HANGERS Note, drawing not to scale Bob DeRoeck May 31, 05 Holes for #10 selftapping SS screws (pan head). 5.75 1 Bend line Aluminum plate, series 5000 or
More informationPocket Door Kit PD1 / PD2 Installation Instructions. Kit Contents.
Pocket Door Kit PD1 / PD2 Installation Instructions Kit Contents. 1, Create Rough Opening In Stud Wall Construct rough opening ensuring all sides are square and level. Rough opening should be; Height =
More informationMake your own zero clearance throat plate.
Make your own zero clearance throat plate. A picture tutorial By Wayne Breshears One of the more important table saw accessories you can have is a zero clearance insert or throat plate. The close tolerance
More informationHow to Make a Hat Bending Jig
How to Make a Hat Bending Jig MATERIALS One 2" x 8" x 11" long (Base Block) exact measurements are 7 ½" x 1 ½" x 11" (Pine is OK to use, I have used scrap Walnut for my benders) Four pieces of Oak 1" x
More informationKitchen Upper Cabinet: Single Door Cabinets from Scratch
Kitchen Upper Cabinet: Single Door by Cabinets from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for any loss, damage, disappointment,
More informationCowper From Steve Wolverton on the T&TTT forum, Feb 2005 For Reference Only Do not use to build a trailer. Check on Teardrop and Tiny Travel Trailers
Cowper From Steve Wolverton on the T&TTT forum, Feb 2005 For Reference Only Do not use to build a trailer. Check on Teardrop and Tiny Travel Trailers for up to date building information; http://www.mikenchell.com/forums
More informationDIY Field Guide ANDYMARK, INC.
ANDYMARK, INC. Intro For the 2014-2015 FTC Game Cascade Effect, teams can purchase official field hardware from AndyMark, or they can build do-it-yourself (DIY) versions of the same hardware. The competitions
More informationEntrance Cabinet Plans
Entrance Cabinet Plans www.andrewharriswoodwork.com Page 1 of 19 Introduction I have tried to ensure all steps are covered in these plans but if you find any errors in the plans or have a question then
More informationJet-ski with motor boat engine
117.178 Tools required: Vice with bending support Wood glue (water resistant) Scissors Ruler Pencil Round file ø2 ø3 ø4 Drills Jigsaw Sandpaper Super glue Please Note The OPITEC range of projects is not
More informationM o b i l e " S e a g u l l "
1 0 0. 0 5 4 M o b i l e " S e a g u l l " CONTENTS 1 Plywood Sheet (A -body) 10 x 100 x 500 mm 2 Plywood Sheet (B-Wings) 5 x 200 x 590 mm 1 Dowel ø 15 x 500 mm 1 Dowel ø 6 x 50 mm 1 Wooden ball ø 30 mm
More informationDeluxe Cabana INSTALLATION INSTRUCTIONS. INSTALLATION Deluxe INSTRUCTIONS Cabana
INSTALLATION Deluxe INSTRUCTIONS Cabana 1 Deluxe Cabana 10 Year Guarantee On Sanders workmanship Made in NZ Using NZ timber supplies 40+ Years Experience In business since 1975 Professional Install Available
More information