BUILDING A TREE BENCH
|
|
- Nancy Houston
- 6 years ago
- Views:
Transcription
1 INSTRUCTIONS FOR A In just a few steps, we show you how to build your own tree bench and paint it perfectly.
2 1 SIDE PIECES OF THE SEATING SURFACE Purchase the materials from the enclosed list. Draw a 10 x 10 cm grid on a board and transfer the outline of the side pieces from the enclosed sketch (left image). Cut out the parts using a jigsaw. Then sand and round off the edges. Coarsely cut the slats (35 mm x 55 mm), align them and draw on the centre point (right image). 2 CUTTING THE SEAT TO SIZE Align at a 90-degree angle and using 1 cm spacer blocks (left image). Then draw on the overhang at a 30-degree angle. Place the wood for connecting the seating surface on the underside and first draw on the overhang and then cut it off (right image). 3 GLUING THE SEATING SURFACE Before the seat slats are screwed to the seat connecting piece, glue must be applied. Then screw the slats into place (left image). Place the lath for the front edge of the seating surface in position and transfer the angles of the two angled sides. Here too, glue must be applied before connecting the screws. The seat surfaces are glued to the side pieces and then screwed into place (right image). Tip: Use screw clamps to temporarily fix the parts in place. Round off the front seat edge with an electric sander. 4 BACKREST Determine and then draw on the position of the slats for the backrest (left image). Using a measuring tape or metre rule, measure out the long side of the slats for the backrest. Also determine the angle (30 ) and inclination (3 ). Shorten the slats for the backrest with a cross-cut at the ends at a 30 angle. Tip: Use a mitre saw. Glue in the slats and then screw them into place (right image).
3 5 INSTALLATION Line the elements up next to each other and secure using a hand clamp. Drill the bench elements using an 8 mm wood drill bit (left image). Open up the pre-drilled hole from the other side using a 10 mm wood drill bit to a depth of approx. 2 cm. This is needed in order to be able to screw in the connecting sleeve later. The connecting sleeve is screwed in using a flat screwdriver (right image). 6 PREPARING THE SPRAYER Open the tin containing the paint in the required colour using the stirrer included and align the suction pipe on the spray attachment so it is facing forwards. Fill paint up to the 3/4 mark on the paint container and dilute it. Place the stirrer against the base of the filled paint container. The distance between the notches represents a dilution of 10%. Stir the paint well and carry out a test spray. The spray nozzle can be positioned in three different directions. A horizontal jet to work from top to bottom, vertical for right to left or selective for particularly intricate areas. The quantity of paint is full adjustable with the dial on the trigger. 7 THE SPRAYING PROCESS Start with corners, edges and angles and then spray the surfaces. Spray from the outside with a uniform distance over the slats. Only change the direction of spray outside the slats. This avoids a build-up of thicker layers of paint during direction changes. Tip: Since paint applied too thickly can cause drips, it is better to spray two thin coats. After spraying, allow the paint to dry in accordance with the manufacturer's instructions. 8 CLEANING Clean the spray attachment thoroughly with water or solvent after use.
4 APPENDIX List of materials Item in drawing Description Dimensions Material Comment Side parts 1 12 Side panels 700 x 1200 Plywood 24 mm Backrest 2 6 Upper cross-beam 362 Squared timber 35 x Second cross-beam from the top 380 Squared timber 35 x Third cross-beam from the top 390 Squared timber 35 x Bottom cross-beam 400 Squared timber 35 x 55 Seating surface 6 6 Rear seating board 470 Squared timber 35 x Second seating board 555 Squared timber 35 x Middle seating board 635 Squared timber 35 x Second seating board from the front 785 Squared timber 35 x Front seating board 830 Squared timber 35 x Support strip for cross-beam 650 Strip 20 x Connecting slats other 370 Squared timber 35 x Construction glue or wood glue 14 Stainless steel wood screws 15 6 Connecting sleeves M Cross-head screw M8 17 Wood stain or similar
5 APPENDIX Sketch DO IT YOURSELF!
BUILDING A GOAL WALL DO IT YOURSELF! INSTRUCTIONS FOR A GOAL WALL
INSTRUCTIONS FOR A In just a few steps, we show you how to build your own goal wall and paint it perfectly. COMPILED BY 1 PREPARING Purchase the materials from the enclosed list. The DIY store should be
More informationRobert Bosch GmbH. Minimalist washstand
Minimalist washstand Neat and tidy Minimalist washstand Minimalist design in the bathroom is in fashion. And rightly so, as this washstand proves: because less is more! 1 Introduction Here s an idea to
More informationMyOutdoorPlans.com. By Julian King [2X4 GARDEN BENCH]
MyOutdoorPlans.com By Julian King [2X4 GARDEN BENCH] CUT LIST A 2 pieces of 2 4 lumber 24 long, 2 pieces 32 1/2 long LEGS B 2 pieces of 2 4 lumber 45 long, 2 pieces 15 1/2 long, 1 piece 12 1/2 long SEAT
More informationBuild Instructions for Towers of Doom
Build Instructions for Towers of Doom 1. Measure and cut 4 x 8 sheet of plywood in half (or ask Home Depot to do it!). You will use one 4 x 4 sheet for the course base. 2. Attach a support frame to the
More informationAsk your DIY store or carpenter to cut the required boards to size. Instructions. 1. Cut out the opening for the bottles
KITCHEN TROLLEY Next time you're whipping up some magic in the kitchen, take advantage of our willing assistant. Fixed on rollers to provide easy mobility, our kitchen trolley can be stationed wherever
More informationRobert Bosch GmbH. Wall organiser
Wall organiser The organisational talent Wall organiser Say goodbye to messiness! The wall organiser is the ideal place to store everything that tends to lie around. 1 Introduction Wardrobes, drawers and
More informationRobert Bosch GmbH. Lounge light fixture
Lounge light fixture Nice and relaxing Lounge light fixture Light has an important effect on mood. This cool light fixture is perfect for creating a cosy lounge atmosphere. 1 Introduction This cool light
More informationKreg Tool Co. All Rights Reserved.
Version 1 p. 1 Materials: Lumber: Qty: Board 2 2x2s 3 ft. long 2 1x2s 8 ft. long 2 1x3s 8 ft. long 6 1x6s 10 ft. long INSTRUCTIONS: Supplies: 1 1 / 4" Kreg Screws (coarse thread for softwoods, fine thread
More informationPROJECT PLANS ROLLING LAUNDRY SORTER
R PROJECT PLANS ROLLING LAUNDRY SORTER Sorting laundry certainly doesn t rank high on anyone s list. So, anything that makes this task easier is welcome. If that functionality can be mixed with a bit of
More informationDIY CHILD S STOOL. Instructions
DIY CHILD S STOOL Children have their own special world. And having the right furniture is part of that world. We have designed an easy-to-assemble child's stool that you can paint in a selection of bright
More informationChief s Shop: Simple Woodworking Bench
Chief s Shop: Simple Woodworking Bench Be sure to read the instructions and review the illustrations and accompanying video for this project BEFORE you start. Follow ALL SAFETY GUIDELINES AND RECOMMENDATIONS
More informationDIY Farmhouse Cabinet
DIY Farmhouse Cabinet Addicted2DIY.com *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever
More informationCOFFEE TABLE WITH RECESSED TRAY
COFFEE TABLE WITH RECESSED TRAY Why not treat your guests to a tray laid with delicacies and then remove it from sight in your new coffee table. There's no easier way to show that you are a thoughtful
More informationDIY RUSTIC HALL TREE
DIY RUSTIC HALL TREE *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever using power tools
More informationPROJECT PLANS PATIO PLANTER BOX
PROJECT PLNS PTIO PLNTER BOX This great-looking planter makes the perfect place for your favorite plants and flowers. It s sized to hold an 18" round plastic pot, which you can pick up in any garden center.
More informationADULT. Adirondack / Muskoka Chair Plans
ADULT Adirondack / Muskoka Chair Plans Materials List 3/4" x 9 1/2" (1.9cm x 24.1cm) redwood, cedar or pine boards. Six, 8' (2.44m) boards should make one chair depending on knots and layout. You can also
More informationShed Assembly Instructions
Shed Kit Contents The shed kit includes all the parts needed to assemble your shed except for tools and fasteners such as screws and nails. The various pieces are pre-cut and many are marked to indicate
More informationProject Skill Level: INTERMEDIATE Plywood Used: CANPLY EXTERIOR Good Two Sides (G2S) or precision sanded Aspen
Project Skill Level: INTERMEDIATE Plywood Used: CANPLY EXTERIOR Good Two Sides (G2S) or precision sanded Aspen MATERIALS LIST: (1) ¾" x 4 ft x 8 ft plywood panel (20) #8 x 2" Robertson or Phillips wood
More informationPROJECT PLANS WOODEN GIFT BOX
PROJECT PLANS WOODEN GIFT BOX Make the gifts you give even more special by presenting them in this one-of-a-kind gift box. In fact, the box may be valued more than whatever it contains. The box is sized
More informationWall-mounted folding desk.
Wall-mounted folding desk. Step-by-step project The wall-mounted folding desk: ideal for small rooms. Are big desks not doing it for you? We feel the same way. They take up a lot of space, especially in
More informationPorch. Swing. Build A. farmstead: project
farmstead: project Porch Build A Swing Instructions Cut all parts to fit as you assemble the project and use the Parts List and Cutting Diagram as a guide for dimensions. When gluing pieces together, you
More informationCoffee table with recessed tray
Coffee table with recessed tray Dinner is served Coffee table with recessed tray This coffee table has it all: it contains a recessed tray, so that you can treat your guests to various delicacies. 1 Introduction
More informationHow to Build A Porch Swing
How to Build A Porch Swing SUPPLIES USED Tape measure Drill 2.5" Wood Screws 1.5" Wood Screws 2" Finishing nails Hammer (or nail gun if you're lucky) Sand paper/ Electric sander Exterior paint Safety glasses
More informationPROJECT PLANS HOBBY BENCH
PROJECT PLANS HOBBY BENCH This great-looking bench provides the perfect place to pursue a variety of hobbies. It offers a large bench top with built-in trays for small items, plus shelves up above to hold
More informationPROJECT PLANS EXPANDABLE CRAFT CENTER
R PROJECT PLANS EXPANDABLE CRAFT CENTER Whether you re working on craft projects, sewing, or pursuing another hobby, this craft center offers a great place to work. It features a large work surface that
More informationCopyrighted Material Page 1
Compare to: Pottery Barn Teen Storage Bed System Skill Level: Beginner Working with the rest of the components in the Storage Bed Collection, the Small Hutch fits on top of the Storage Headboard and will
More information-1- Coach Instructions.
-1- Coach Instructions. Insert the bogie pivot pins through the bottom of the coach body ensuring the dimples fit into the recesses. Glue the.06 x.25 short strips each side of the pivot head, bridge the
More informationBuilding Instructions Diva cabin boat
Building Instructions Diva cabin boat Order no. 3093/00 aero-naut Modellbau Stuttgarterstr. 18-22 D-72766 Reutlingen / Germany http://www.aero-naut.com 1 For pictured building instructions please see the
More informationindicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
f a r m h o u s e d i ni ng b e nc h What You'll Need lumber 6-2x3x8 6-1 x6x8 (availability will vary) Intermediate or equivalent 8/4 lumber planed to 1 1/2" for the 2x hardware/supplies 1 1/4" pocket
More informationBuild a comfortable outdoor seat in time for spring
asy lider Build a comfortable outdoor seat in time for spring by Vern rassel Our glider features metal swing arms that are easy to install and provide a smooth gliding motion. W hen you re choosing a spot
More informationGrade 11 Woods Lift Lid Coffee Table. Based on Under the big Top from Popular Mechanics Website
Grade 11 Woods Lift Lid Coffee Table Based on Under the big Top from Popular Mechanics Website TABLE TOP 1. Select enough lumber to construct a top that is between 22 ½ and 24 wide after jointing. Ensure
More informationCOMPLIMENTARY WOODWORKING PLAN
COMPLIMENTARY WOODWORKING PLAN ORIENTAL GARDEN ARBOR PLAN This downloadable plan is copyrighted. Please do not share or redistribute this plan in any way. It has been paid for on your behalf by JET Tools,
More informationCopyright 2010 Springbok Publishing All Rights Reserved- Page 1
Copyright 2010 Springbok Publishing All Rights Reserved- www.woodensaddlerackplans.com Page 1 Legal Information All contents copyright 2010 by Springbok Publishing. All rights reserved. No part of this
More informationHudson Dresser [1] Hudson Dresser Published on Ana White ( Submitted by dan-k [2] on Fri, :43 [1]
[1] Submitted by dan-k [2] on Fri, 2011-03-11 11:43 [1] If you plan on staining this piece, it is recommended that you stain all of the drawer face materials before assembly for a more professional look.
More informationPLANS BY KELLEY FARMHOUSE DESIGNS LOFTED DORM ROOM BED
PLANS BY KELLEY FARMHOUSE DESIGNS LOFTED DORM ROOM BED DIMENSIONS: 82" X 70" X 45" DIFFICULTY LEVEL: INTERMEDIATE TOOLS REQUIRED ONE+ Circular Saw ONE+ AirStrike 16GA Finish Nailer ONE+ Impact Driver ONE+
More informationModel #SH & CH SH Pine CH Naturaline
Model #SH304-101 & CH304-101 Assembly Manual SH304-101 Pine CH304-101 Naturaline Component Parts A 2 ea. Angled Rail - 2 x 4 x 107-1/8" B 1 ea. Center Angled Rail - 2 x 4 x 107-1/8" C 9 ea. Rock Board
More informationBuilding Your Faith Chest
Building Your Faith Chest You will need the following tools: 1 Phillips screwdriver Hammer Wood Glue (optional) Sanding Block (optional) Tape Measure (optional) Step 1: Step 2: Step 3: Step 4: Step 5:
More informationThe Festival Assembly Instructions
The Festival Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown CONTACT INFORMATION: HomePlace Structures 301 Commerce Drive New
More informationMudroom Unit. Page 1 of 25
Mudroom Unit www.andrewharriswoodwork.com Page 1 of 25 Introduction This plan makes a unit which is 66 ¾ inches tall, 39 ½ inches wide and 18 ½ inches deep. It was custom made for some friends to fit the
More informationDresser. Materials & Tools FEATURING FORMALDEHYDE-FREE TECHNOLOGY. Free Plans to build a Dresser
Free Plans to build a Dresser Materials & Tools Materials: 1-1/4 pocket hole screws 1-1/4 brad nails 3 sets of 18 drawer slides Drawer pulls Edge banding, optional Wood glue Sandpaper (100, 150, 220 grits)
More informationSauna & Steam. Vision Sauna Manual Wall Hung Heater Version (Covers all models)
Vision Sauna Manual 14.7.18 Wall Hung Heater Version (Covers all models) Oceanic Ltd, Pountney Street, Wolverhampton, WV2 4HX Phone: 01902 450 550 sales@oceanic-saunas.co.uk www.oceanic-saunas.co.uk Table
More informationwoodworkersjournal.com MATERIAL LIST
MATERIAL LIST T x W x L 1 Legs (2) 1 1 2" x 3 1 2" x 36 7 16" 2 End Uprights (2) 1 1 2" x 3 1 2" x 32 1 2" 3 Stringers (4) 1 1 2" x 3 1 2" x 42" 4 Top Cladding, Long (2) 3/4" x 7 1 4" x 65 3 4" 5 Side
More informationSafety First! Use eye protection, always! Use ear protection with loud power tools. Stay with children while they work!
TM TM ART TABLE Safety First! Use eye protection, always! Use ear protection with loud power tools Stay with children while they work! Follow tool manufacturers safety guidelines Page 1 ART TABLE Page
More informationFrameless Inline Door With Return QCI5263
INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges
More informationC & C 30 MK II % Cockpit Seat Backrests. Installed on S\V "Wyndisphree" S/N 58 86E18806 (03/23/2000)
C & C 30 MK II % Cockpit Seat Backrests Installed on S\V "Wyndisphree" S/N 58 86E18806 (03/23/2000) C & C 30 MK II Building the Removable Seat Backrests 1. This package contains instructions and sketches.
More informationPROJECT PLANS OUTDOOR SERVING CART
R PROJECT PLANS OUTDOOR SERVING CART Make outdoor entertaining easy with this serving cart. It offers lots of space for storing food, tableware, and outdoor supplies, plus it cradles bottles where they
More informationDIY Corner Bench with Built-in Table
DIY Corner Bench with Built-in Table Free woodworking plans for building a corner bench with a built-in table in the center. Cost: ~$75 Difficulty: Intermediate PINSPIRATION MOMMY 1 TOOLS AND SUPPLIES:
More informationCountryAccents Pergola Assembly Instructions
CountryAccents Pergola Assembly Instructions Options 11 2" Squares Lattice Railing Gingerbread Scroll (For 5" Posts Only) Site Preparation Site preparation for either the round column or the 5" post pergola
More information1 ¼-inch Pocket Screws Brad Nailer or Hammer 1 ¼-inch Brad Nails Clamps
MATERIALS: TOOLS: (4) 2 x 6 x 8 Ft. Boards Tape Measure (2) 2 x 4 x 8 Ft. Boards Carpenter s Square (7) 1 x 4 x 8 Ft. Boards Pencil (2) 1 x 3 x 8 Ft. Boards Drill (1) Half Sheet of ¾-inch Thick Plywood
More informationRetrofit Apron Front Farm Sink With Dual Mount Capability Installation Instructions
For Under-Mount Installation please refer to page 14 FOR EXPERIENCED AND PROFESSIONAL INSTALLATION ONLY This installation project is designed for an advanced skill level. Disclaimer: Undermount Application
More informationFLOW HIVE ASSEMBLY GUIDE. If we look after the bees they will look after us, and the honey really is an amazing bonus. Flow Hive Hybrid 3 Frame
AUSTRALIAN MADE If we look after the bees they will look after us, and the honey really is an amazing bonus. FLOW HIVE ASSEMBLY GUIDE Flow Hive Hybrid 3 Frame Read all instructions first. If you are unfamiliar
More informationMATERIALS: TOOLS: CUT LIST:
MATERIALS: TOOLS: (2) 2x2x8 Ft. Boards Tape Measure (2) 1x4x8 Ft. Boards Pencil (4) 1x2x8 Ft. Boards Carpenter s Square (1) 4x4 Ft. Sheet of ¾-Inch Plywood Drill with 5/16-inch Drill Bit (1) 1 ½-inch Thick
More informationHow To Build Horizontal Slat Fences and Screens
How To Build Horizontal Slat Fences and Screens All Day Fencing Construction and design guide: www.alldayfencing.com.au p: 1300 633 623 Construction and Design of Horizontal Slat Fences and Screens First
More informationSmall 45 Roof Houses 1 or 2 Story 1 /24 th Scale Patterns
BA GARDEN TOWNS 45 Roof Houses 10" x 10" 1 or Story Scaled and easy to read patterns and instructions for wood houses. Yard and Garden Buildings Compatible with Garden Railroads or a delight for any child's
More informationNational 5 Practical Woodwork
Exercise C. The legs of a chair are turned on the wood lathe. (a) (i) Sketch and name the tool used to produce the square shoulder shown at A. Name of tool: Sketch and name the tool used to check the diameter
More informationJet-ski with motor boat engine
117.178 Tools required: Vice with bending support Wood glue (water resistant) Scissors Ruler Pencil Round file ø2 ø3 ø4 Drills Jigsaw Sandpaper Super glue Please Note The OPITEC range of projects is not
More informationMaking Simple Bookbinding Equipment
Tony Firman 20 1 2 19 Notes Tony Firman Tony Firman Bookbinding 18 3 : 2012 Tony Firman Bookbinding P.O. Box 507 Haslet, TX 76052 www.tonyfirmanbookbinding.com 4. When all the tapes have been pinned in
More informationRouter Table. Construction
Router Table A router table is an invaluable tool. The problem, however, is that ready-built router tables are usually relatively expensive and too narrow for many projects. This router table provides
More information3Position the hull of the ship as
Yamato: Step-by-step 25 The hull and stern deck c b d a b d c e e f a Rear frame b Stern deck x 2 c Stern deck x 2 d Side wall x 2 Wood glue Sandpaper (no. 400 grain) Craft knife Pliers d Side wall x 2
More informationInstallation Guide. Focal Point Architectural Mouldings. Focal Point Architectural Mouldings
Installation Guide Focal Point Architectural Mouldings 6a Howards Road Beverley, South Australia 5009 Ph: 08 8244 7322 Contents Preface... 2 Moulding Application 1. Planning and Estimations... 3 2. Marking
More informationFrameless Inline Door QCI5248
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5248 FRAMELESS PANEL / DOOR / PANEL QCI5248 REV. 0 Page 1 Certified 06/16/2016 Parts List with glass to glass hinges *Quantities may vary. **Support Bar
More informationHow-to-Install. Laminate Countertops and Sheet Laminate. FREE brochure Reverso en español
FREE brochure Reverso en español How-to-Install Laminate Countertops and Easy to install instructions provided inside Multiple colors available for unique design options Durable and easy to care for Accessory
More informationClock 35 - Toyland. Construction instructions for Clock 35
This clock has been designed for children, it is a stand-alone unit and can be positioned on a shelf or cabinet out of the reach of very young hands who may be tempted to touch. The clock is shown in two
More informationInstallation Manual Using Existing Handrail Version 4.0 Oct 2017
Installation Manual Using Existing Handrail Version 4.0 Oct 2017 ORDER OF ASSEMBLY TOOLS YOU WILL NEED - Fine Saw - Sander - Wood Filler - Allen keys - Screw Driver - Drill - Suitable Screws PROTECTING
More informationEasy Five Cube Tower Bookshelf. Copyrighted Material. Page 1
Compare to: Land of Nod Cube Collection, 5 Cube Tower Bookshelf Skill Level: Beginner Easy Five Cube Tower Bookshelf This fully framed five cube tower can hold everything from towels to boots to books
More informationInstallation Guide 1
1 2 Contents Before you begin Storage & preparation Tools & materials you may need Getting started Sink & cooktop cut-outs Cabinet Joins for 20mm benchtops Joining & installation of 20mm benchtops Joining
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 1
Kentucky 4H Wood Science Plans Notebook Plans Level 1 MATERIALS NEEDED: 1 piece wood 3/4" x 2 x 2 1 piece wood 3/4" x 3 x 3 1/2" 1 wooden spring-type clothespin 2-1 1/2" nails 1-1/2 woodscrew Wood Glue
More informationCONTINUED. BACK & SEAT RAILS: 1. Sort three (3) 2x2x8 pieces. 2. Measure and cut one (1) 61 length from each piece.
# Materials: Quantity Each: Total Quantity: 2x2x8 6 2x4x8 9 4x4x8 2 4x6x8 1 TIPS FOR SUCCESSFUL PREP WORK: Before starting, carefully read through the entire instruction sheet. Refer to the material list
More informationHow to Build a Recessed Medicine Cabinet
How to Build a Recessed Medicine Cabinet See post for install info http://www.hertoolbelt.com/recessed-medicine-cabinet/ Materials 6 Inset Cabinet Door Hinges 3 Latches 1 sheet Beadboard or 1/4 plywood
More informationInstallation Instructions and Details
Installation Instructions and Details Contents Page General Notes 2 Typical System Perspective 3 Panel, Hardware & Trim Details 4-6 Hardware & Trim Fabrication Details 7-9 Installation Procedures 10-12
More informationining Table Materials *Notes on Materials
D ining Table We looked around for the perfect table for the dining room. Some were too big, some too small, and most were just too expensive. So we built this one, and we are happy with the result. It
More information1Take the keel (3) and
1 The hull and the bridge 1Take the keel (3) and apply PVA wood glue in the second slot from the left: a toothpick may make it easier. Take care: the left end is the one that has a projection. THE HULL
More informationWall Panel Installation Instructions
Panel Installation Instructions Demolition - Common Tools Needed Reciprocating Saw Allen Wrench Set Hole Saw Set Pry Bar Dust Pan and Brush Putty Knife / Scraper Hex Bit Socket Set All Necessary Safety
More informationJeff Branch WOODWORKING YOU CAN BUILD A. By adding subtle design elements, a traditional furniture style becomes decidedly modern.
Jeff Branch WOODWORKING YOU CAN BUILD A By adding subtle design elements, a traditional furniture style becomes decidedly modern. Jeff Branch WOODWORKING Publisher: Jeff Branch Editor: Jeff Branch Art
More informationSideboard. Essential design. Sideboard Unique eye-catcher and practical storage space all at once: The sideboard with fashionable multimaterial
Sideboard Essential design. Sideboard Unique eye-catcher and practical storage space all at once: The sideboard with fashionable multimaterial design. 1 Introduction From multi-material to one of a kind!
More informationTryde Media Hutch. Copyrighted Material. Page 1
Compare to: Pottery Barn Hyde Media Console Skill Level: Intermediate Tryde Media Hutch Following the great success of so many readers with the Tryde Collection, inspired by Pottery Barn s popular Hyde
More informationOutdoor Swing and Arbor
America s leading woodworking authority Step by Step construction instruction. A complete bill of materials. Outdoor Swing and Arbor Exploded view and elevation drawings. How-to photos with instructive
More informationAmerica s leading woodworking authority To download these plans, you will need Adobe Reader installed on your computer. If you want to get a free copy, visit: http://adobe.com/ reader. Having trouble downloading
More informationDisplay Case (for J&S)
Display Case (for J&S) This is constructed of maple plywood with solid maple (soft maple) edge banding. It was made to fit between a door and a kitchen cabinet, and has an elegant circular taper between
More informationComputer Desk. Project designed by April Wilkerson
Project designed by April Wilkerson Copyright WilkerDos.com 2018 Project plan Desk Page 2 of 16 Page 3 of 16 File cabinet Page 4 of 16 Metal base Page 5 of 16 Glue up Get started by gluing up boards for
More informationG. Building the Cab, Cab Roof and Cab Boiler Extension Page 14 and Backhead.
G. Building the Cab, Cab Roof and Cab Boiler Extension Page 14 and Backhead. Cab. In order to ensure that the cab and tender would actually look right, as what often appears on a drawing is not always
More informationDIY Wine Storage Cabinet
DIY Wine Storage Cabinet ADDICTED2DIY.COM *Before beginning this project, please read through all of the plans and the blog post. When building this project, be sure to measure your wood and cut to fit.
More informationARTS AND CRAFTS CHAIR
ARTS AND CRAFTS CHAIR 491 MATERIALS LIST--DINING CHAIR Key No. Size and description (use) A 2 1-3/4 x 1-3/4 x 16-1/4'' oak (front leg) B 2 1-3/4 x 3-3/4 x 40-1/2'' oak (rear leg) C 1 1-3/4 x 3-3/16 x 15''
More informationFUSELAGE CONSTRUCTION
FUSELAGE CONSTRUCTION Note: prior to building and gluing on the work surface use protective covering on your building surface. (wax paper or clear wrap) Fit the laser cut Fuselage Front and Fuselage Rear
More informationHow to build a Ram for Challenge E: Twist-O-Rama
How to build a Ram for Challenge E: Twist-O-Rama Notes The Ram is like the Structure Tester it is not Interference for a Team Manager or other non-team members to build it. Construction time is approximately
More informationthe wire, less is better. And make sure the bends on each truss wire are in line with the other. See the next photo.
The following information and photographs are what I did to build the kit. Your methods and needs may differ from this which is fine. There is no right or wrong way if you are used to scratch building.
More informationDIY X Panel Side Table
DIY X Panel Side Table *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever using power tools
More informationEXTREME LOAD no. TWO
1602 - EXTREME LOAD no. TWO Kit Features: 22' 4 " x 14' x 3'-6 Oversize Load 49mm (1.9") actual height Bolt Head Details Welded Load Mounting Fins Painting Handles Tools Required: Hobby Knife Tweezers
More informationChest of Drawers Plans
Chest of Drawers Plans www.andrewharriswoodwork.com Page 1 of 15 Introduction This plan makes a chest of drawers that is 50 inches at the widest point, 19 inches deep and 40.75 inches high. I have tried
More informationMLCS Instructions for Bowl and Tray Template Kit #9176/#9179
MLCS Instructions for Bowl and Tray Template Kit #9176/#9179 Tools Needed: Router 1-1/2 h.p. Minimum recommended with a 1/2 collet Forstner bit 3/4-2 recommended depending on template used Drill Press
More informationProject 12231EZ: Country Curio Clock
Project 12231EZ: Country Curio Clock This good-looking clock not only reminds you of the time, it also provides a couple of shelves to display favorite curios. No fancy joinery is needed here, just butt
More informationSmall Town Buildings. Scaled and easy to read patterns and instructions. Shoe / Western Union (with and without porch)
1 /24 th Scale Patterns kiva design G R O U P E 1 Story Flat Roof Yard and Garden Buildings Compatible with Garden Railroads or a delight for any child's collection Overall Dimensions Foundation: 10" x
More informationSimple Woodworking: Outdoor Pitch Chair
Parts Lumber Front Front Leg Front Leg Drill three pocket holes on each end of the Front - one centered and two 3/4" from each side. Cut a 15-degree miter on one end of the Front Legs. It will be easier
More informationINTRODUCTION. This simple file creates a neat table. for small children to use for multiple purposes. Weather drawing with crayons, putting puzzles
Kids Work Table Remember children will be working on this table so check with your local paint supplier to find one safe for children. A latex based paint was used for this example. Written By: Feitan
More information#P571 - Victorian Queen Fretwork Clock inspired by 18th century Victorian elegance. 17 H x 21 W. Requires a 3 1/2 clock insert.
- Victorian Queen Fretwork Clock inspired by 8th century Victorian elegance. 7 H x 2 W. Requires a 3 /2 clock insert. Cut on dashed line for Back Cut on solid line for Frame only. Stock: /8 - /4, cut each
More informationBefore you Begin... 3 Storage and preparation... 3 Tools & Materials You may Need... 4
Installation Guide Installation Guide Contents INTRODUCTION... 2 Before you Begin... 3 Storage and preparation... 3 Tools & Materials You may Need... 4 Adhering your Think Solid benchtop to your cabinets
More informationAssembly Instructions
V2-05.16 Assembly Instructions (W x D x H): 2.20m x 2.20m x 2.49m Product Name: Brighton Corner Arbour Pressure Treated products should not be treated with any other products for the first month. PLEASE
More information(28) 2 x 4 x 8 Ft. Boards Tape Measure (9) 2 x 6 x 8 Ft. Boards Pencil (6) 2 x 2 x 8 Ft. Boards Carpenter s Square (9) 1 x 3 x 8 Ft.
MATERIALS: TOOLS: (28) 2 x 4 x 8 Ft. Boards Tape Measure (9) 2 x 6 x 8 Ft. Boards Pencil (6) 2 x 2 x 8 Ft. Boards Carpenter s Square (9) 1 x 3 x 8 Ft. Boards Drill 2 ½-inch Pocket Screws Circular Saw 2
More information#P570 - Leavenworth Requires a pendulum movement kit (#A309 - #A312) 24 H x 14 W
- Leavenworth Requires a pendulum movement kit (#A309 - #A32) 24 H x 4 W Cut on dashed line for Back Cut on solid line for Frame only. Stock: /8 - /4, cut each Left pattern piece. GENERAL SCROLLSAW TIPS
More informationB A T H R O O M G L A S S
mistley B A T H R O O M G L A S S vaug16 Page 2 Thank you for purchasing this Trinity shower screen. Please study these instructions carefully before assembly and installation and check all supplied parts
More information