Computer Desk. Project designed by April Wilkerson
|
|
- Wendy Miles
- 5 years ago
- Views:
Transcription
1 Project designed by April Wilkerson Copyright WilkerDos.com 2018
2 Project plan Desk Page 2 of 16
3 Page 3 of 16
4 File cabinet Page 4 of 16
5 Metal base Page 5 of 16
6 Glue up Get started by gluing up boards for the top. Pick your nicest boards, joint the edges, and glue up a slab that s larger than the finished desk top. You ll cut it to final size later. Biscuits in each glue joint aren t required, but they ll help keep the boards aligned so you do less flattening later. Welding While the glue is drying on your top, make the metal base. Cut the tubing to size, prep the ends, and weld the base sides. Grind the welds smooth. Weld the horizontals to the ends, making sure the ends are square to the horizontals. Clean up your welds and paint the base. Page 6 of 16
7 Make the desk sandwich Sand the top to clean up the glue seams, and cut the top to size. Make the desk dividers and back. Drill pocket holes in the top edge of the back, and in the back end of the two middle dividers. Pocket holes won t work on the end pieces, so predrill and drive 1-1/2 screws through the back to secure these parts. Assemble all five pieces. It s a GREAT idea to install the drawer slides now. The drawer compartments are small, so getting inside them later to install slides will be nearly impossible. This is also the time to cut slots for the table top fasteners, which can easily be done with a biscuit joiner. Do test cuts on scrap to make sure your biscuit joiner fence is correctly located for the fasteners. Put two slots in each divider. Place the desk top upside down on your work bench (be sure to use a pad or carpet scrap to protect the face) and position the dividers/back assembly upside down on the bottom of the top. With the edges correctly aligned, clamp them together. Use the pocket holes and table top fasteners to complete the assembly. Don t use glue! Glue would prevent the top from expanding and contracting independently of the dividers and back. Page 7 of 16
8 Screw the bottom to the dividers and back using eighteen 1-1/2 screws. Three screws per divider. When you do your final assembly, you can glue these components together but for now, just screw them. This allows you to take the bottom off so you can apply finish to the inside surfaces. Build the drawers Carefully measure the openings in your desk and make your drawer parts. Be sure to allow for the drawer slides. Glue and nail the sides to the bottom using 1 nails. Glue and nail the front and back to the sides and bottom. Attach the drawer box component of the slide to the drawer sides. Be sure it s going on straight, or the drawer won t work right. Page 8 of 16
9 Make the drawer fronts, allowing 1/8 gap per side. Be sure to cut your drawer fronts to fit your case. Since these are plywood and will be painted, be sure to seal the edges. Aquacoat Grain Filler works great for this. Build the file cabinet Assemble the case. You could use biscuits on the case corners, or drill and drive dowels from the top and bottom faces, flush cutting them after they re glued in. Use glue and 1-1/2 brads to hold the center divider in place. Install the back after your finishing work is complete. Page 9 of 16
10 Measure carefully and cut your drawer box parts to size. Be sure to allow for the drawer slides. Cut the rabbet in the top edge of the sides so you can use hanging folders in the drawers. Assemble the drawer boxes using glue and brads. Install the slides in the case and on the drawer boxes. Page 10 of 16
11 Measure your cabinet and cut the drawer fronts to fit, allowing 1/8 gap per side. Like the other drawer fronts, seal the edges prior to painting. Finishing On my desk I decided to stain some components, and paint others. I used Aquacoat s Provincial stain, and Antique White paint. This gives the desk a very attractive contrast. Do your finishing and painting with all the parts as separate components. Page 11 of 16
12 Assembly Once the finish is dry, permanently fasten the desk bottom to the back and dividers. You can then fasten the desk to the base. I used 1-1/2 x 1-1/2 angle iron to create a bracket between the metal base and the wooden components. You could also drill through the X horizontals and drive screws through the horizontals into the desk bottom. With the drawer boxes installed, attach the drawer fronts. A neat trick for this is to use a small dab of CA (cyanoacrylate) glue between the back of the drawer front and the front of the drawer box as you re positioning the drawer front. Hold the front in place for a few seconds, till the glue grabs. A piece of masking tape stuck to the inside of the drawer box and draped over the drawer front will give you something to pull so you can open the drawer and screw the box and front together. Install the pulls. Follow the same procedure to install the drawers in the file cabinet. Install the casters on the file cabinet. Be sure you protect the top when you flip the cabinet over. Your desk is ready to go to work! Page 12 of 16
13 Cut Lists, Sheet Lay Out and Sources The desk top requires approximately 16 board feet of solid wood, or four 1 x 6 x 6 boards. Cut List: ¾ Plywood-project requires one sheet Part # Quant Part Dimensions Material Notes 1 1 Desk Bottom ¾ x 20 x 72 Ply 2 4 Desk dividers ¾ x 3-5/8 x 19-1/4 Ply 3 1 Desk back ¾ x 3-5/8 x 72 Ply 4 2 Side drawer fronts ¾ x 3-1/2 x 21-1/16 Ply Seal edges prior to painting 5 1 Mid drawer front ¾ x 3-1/2 x 26-1/8 Ply Seal edges prior to painting. 6 2 File cab sides ¾ x 18 x 21-1/2 Ply 7 2 File cab top and ¾ x 18 x 15-1/2 Ply bottom 8 2 File cab drawer fronts ¾ x 10-1/4 x 13-3/4 Ply Seal edges prior to painting 9 1 File cab rail ¾ x ¾ x 14 Ply 1 Desk top ¾ x 20 x 72 Solid Glue slab up oversized. Cut to finished size after creating desk base. Note: Dimensions for ¾ plywood parts 1, 2, 3, 6, 7, 9 are based on using iron-on edge banding. If solid banding is used, adjust the dimensions accordingly. Page 13 of 16
14 Cut List: ½ Plywood-project requires one sheet 1 6 Desk drawer sides 2 4 Side drawer front and back 3 2 Mid drawer front and back 4 2 Side drawer bottoms 5 1 Mid drawer bottom 6 4 File cab drawer sides 7 4 File cab drawer front and back 8 2 File cab drawer bottoms ½ x 3-1/4 x 17-1/2 ½ x 3-1/4 x 20-1/4 ½ x 3-1/4 x 25-5/16 ½ x 17-1/2 x 19-1/4 ½ x 17-1/2 x 24-5/16 ½ x 9-3/8 x 15-3/4 ½ x 3-3/8 x 13 ½ x 12 x 15-3/4 Ply Ply Ply Ply Ply Ply Ply Ply Check these dimensions against your desk Check the length against your desk Cut rabbet for hanging files in top edge Check the length against your file cabinet Page 14 of 16
15 Cut List: Steel Quantity Part Dimensions Notes 4 End horizontals 2 x 2 x 15-1/4 Long point to long point 4 End X shorts 2 x 2 x 16-1/16 Long point to long point 2 Enc X longs 2 x 2 x 32-1/8 Long point to short point 2 Horizontals 1 x 2 x 68 Supplies Three pair 18" slides Two pair 16" slides Five Drawer pulls Four Casters Iron On Edge Banding Aquacoat Grain Filler Aquacoat Top Coat Zinsser Seal Coat Thank you for purchasing this set of plans. Visit my website to look for other great projects that ll improve your shop and home. Cheers April Page 15 of 16
16 Project notes Page 16 of 16
Chest of Drawers Plans
Chest of Drawers Plans www.andrewharriswoodwork.com Page 1 of 15 Introduction This plan makes a chest of drawers that is 50 inches at the widest point, 19 inches deep and 40.75 inches high. I have tried
More informationHudson Dresser [1] Hudson Dresser Published on Ana White ( Submitted by dan-k [2] on Fri, :43 [1]
[1] Submitted by dan-k [2] on Fri, 2011-03-11 11:43 [1] If you plan on staining this piece, it is recommended that you stain all of the drawer face materials before assembly for a more professional look.
More informationChest of Drawers Plans
Chest of Drawers Plans www.andrewharriswoodwork.com Page 1 of 12 Introduction This plan makes a chest of drawers from 2 by 4s and 2 by 6s for the top. The cabinet is 22 ½ inches at the widest point, 22
More information1 ¼-inch Pocket Screws Brad Nailer or Hammer 1 ¼-inch Brad Nails Clamps
MATERIALS: TOOLS: (4) 2 x 6 x 8 Ft. Boards Tape Measure (2) 2 x 4 x 8 Ft. Boards Carpenter s Square (7) 1 x 4 x 8 Ft. Boards Pencil (2) 1 x 3 x 8 Ft. Boards Drill (1) Half Sheet of ¾-inch Thick Plywood
More informationMaterials and Tools: Printer s Triple Console Cabinet. Free Plans to build a Triple Console Cabinet
Materials and Tools: Materials: 3 sets euro style bottom corner mount drawer slides, 16 length 3 sets inset hinges 24 cup style handles 8 2x2 @ 8 feet long 6 1x3 @ 8 feet long 6 1x2 @ 8 feet long 1 sheet
More informationEntrance Cabinet Plans
Entrance Cabinet Plans www.andrewharriswoodwork.com Page 1 of 19 Introduction I have tried to ensure all steps are covered in these plans but if you find any errors in the plans or have a question then
More informationCABINETRY Assembly Instructions
www.hdicabinetry.com Assembly Instructions TABLE OF CONTENTS Category Page(s) Section 1: Framed Series Base Cabinet Instructions Wall Cabinet Instructions Easy Reach Cabinet Instructions 1.01-1.04 1.05-1.06
More informationCopyright 1998 KDE Technologies
Modular Computer Corner Desk Unit Copyright 1998 KDE Technologies http://members.tripod.com/~kdetech/ 1. Introduction 2. Plans Sheet one - Isometric Sheet two - Top Detail / Corner Unit Sheet three - Leg
More informationMedia Console Table 38"
Copyright 2016 Shanty-2-Chic.com Media Console Table A sleek, modern take on a traditional concept; this console table is as stylish as it is functional and you'll have it done in a weekend. And versatile
More informationAbout.com :
http://woodworking.about.com/gi/dynamic/offsite.htm?sit...//www.popularwoodworking.com/features/fea.asp%3fid=1088 (1 of 8)1/28/2004 12:05:01 AM Modern Storage Tower The last thing I want to do when starting
More informationMudroom Unit. Page 1 of 25
Mudroom Unit www.andrewharriswoodwork.com Page 1 of 25 Introduction This plan makes a unit which is 66 ¾ inches tall, 39 ½ inches wide and 18 ½ inches deep. It was custom made for some friends to fit the
More informationHow to Build a Recessed Medicine Cabinet
How to Build a Recessed Medicine Cabinet See post for install info http://www.hertoolbelt.com/recessed-medicine-cabinet/ Materials 6 Inset Cabinet Door Hinges 3 Latches 1 sheet Beadboard or 1/4 plywood
More informationCopyrighted Material Page 1
Compare to: Pottery Barn Teen Storage Bed System Skill Level: Beginner Working with the rest of the components in the Storage Bed Collection, the Small Hutch fits on top of the Storage Headboard and will
More informationIndustrial Cart. Materials. With High Style Restyle
1 Industrial Cart With High Style Restyle Materials 1 sheet 3/4" plywood 1-1" x 2" x 8' board 2-1" x 3" x 8' board 1-2" x 8" x 10' board 1-2" x 6" x 8' board 3-1/4" x 2 1/2" x 4' poplar hobby boards, or
More informationThe first step is to cut all wood to proper size. Refer to the cutting schedule and Details 1 and 2 for further instructions.
CHILD S ARMOIRE 275 THIS CHILD'S ARMOIRE will make it easy for kids to keep their rooms neat and orderly. Its six drawers and two shelves provide enough storage space to house a substantial wardrobe. By
More informationEco Office File Base. Materials and Tools: Free Plans to build an office file cabinet base
Materials and Tools: Materials: 1 - Sheet 3/4 PureBond Hardwood Plywood (Available at the Home Depot) 1 - Sheet 1/4 PureBond Hardwood Plywood (Available at the Home Depot) 3-21 Drawer Slides, Euro Style
More informationMATERIALS: TOOLS: CUT LIST:
MATERIALS: (3) 4x4x8 Ft. Boards (8) 2x4x8 Ft. Boards 2 ½-inch Pocket Screws 2 ½-inch Wood Screws 1-inch Wood Screws (16) Figure 8 Tabletop Fasteners Wood Glue Wood Filler TOOLS: Tape Measure Pencil Carpenter
More informationAmerica s leading woodworking authority To download these plans, you will need Adobe Reader installed on your computer. If you want to get a free copy, visit: http://adobe.com/ reader. Having trouble downloading
More informationBrookfield Storage Bed Frame. Copyrighted Material. Page 1
Compare to: Pottery Barn Kids Brookfield Storage Bed Frame Skill Level: Intermediate Brookfield Storage Bed Frame Matching the Brookstone Headboard, the storage bed takes advantage of ALL the space under
More informationShop Projects. Plans NOW. Each Built from One Sheet of Plywood!
Plans NOW www.plansnow.com 5 Shop Projects Each Built from One Sheet of Plywood! Tool Tote - Sawhorse - Workbench - Wood Bin - Wall Cabinet PLUS: 7 SHOP SECRETS Working with Plywood Dread the thought of
More informationNEXUS SERIES CABINETS
NEXUS SERIES CABINETS STANDARD BASE ASSEMBLY INSTRUCTIONS Also applies to: Galaxy Series, Nexus Series, Ridgeline Series, Statesman Series, and Waterford Series FOR YOUR INFORMATION: These assembly instructions
More informationEasy Five Cube Tower Bookshelf. Copyrighted Material. Page 1
Compare to: Land of Nod Cube Collection, 5 Cube Tower Bookshelf Skill Level: Beginner Easy Five Cube Tower Bookshelf This fully framed five cube tower can hold everything from towels to boots to books
More informationDrill Press Storage Cart
Drill Press Storage Cart Richard Hicks on July 22, 2013 Drill Press Storage Cart Drill Press Storage Cart My Inspiration ShopNotes Issue 128 Changes Used casters instead of wheels Didn t build the drill
More informationDIY Full-Size Captain s Bed with Storage. Addicted2DIY.com
DIY Full-Size Captain s Bed with Storage Addicted2DIY.com Before beginning this project Please read through all of the plans as well as the blog post associated with this project. Always use safety precautions
More informationPROJECT PLANS EXPANDABLE CRAFT CENTER
R PROJECT PLANS EXPANDABLE CRAFT CENTER Whether you re working on craft projects, sewing, or pursuing another hobby, this craft center offers a great place to work. It features a large work surface that
More informationRobert Bosch GmbH. Minimalist washstand
Minimalist washstand Neat and tidy Minimalist washstand Minimalist design in the bathroom is in fashion. And rightly so, as this washstand proves: because less is more! 1 Introduction Here s an idea to
More informationCedar 2-Drawer Desktop Storage Cube
Cedar 2-Drawer Desktop Storage Cube 5 ½ Dimensions 5 ½ 5 ½ 2 2 1 7/8 4 ¼ 4 ½ Author s Notes: Build a Cedar 2-Drawer Desktop Storage Cube from just 1 cedar fence picket. No angles, special cuts or rips
More informationBathroom Storage Unit. Wilkerdos.com
Bathroom Storage Unit Wilkerdos.com Copyright 2015 Material List Quantity Item Notes 1 4 x 8 x 3/4 plywood Construction grade 1 2 x 4 x 1/2 plywood Construction grade 11" 7-1/2" Page 1 Some 1 1/4" brad
More informationHarriet Chair with Modifications
Harriet Chair with Modifications This modification of the Harriet chair includes a slat back, padded seat, and is 2 inches wider than the original plan. The overall dimensions of the finished chair: 38
More informationCopyright 2010 Springbok Publishing All Rights Reserved- Page 1
Copyright 2010 Springbok Publishing All Rights Reserved- www.woodensaddlerackplans.com Page 1 Legal Information All contents copyright 2010 by Springbok Publishing. All rights reserved. No part of this
More informationDresser. Materials & Tools FEATURING FORMALDEHYDE-FREE TECHNOLOGY. Free Plans to build a Dresser
Free Plans to build a Dresser Materials & Tools Materials: 1-1/4 pocket hole screws 1-1/4 brad nails 3 sets of 18 drawer slides Drawer pulls Edge banding, optional Wood glue Sandpaper (100, 150, 220 grits)
More informationClassic Kitchen Island
America s leading woodworking authority Step by Step construction instruction. A complete bill of materials. Classic Kitchen Island Exploded view and elevation drawings. How-to photos with instructive
More informationTryde Media Hutch. Copyrighted Material. Page 1
Compare to: Pottery Barn Hyde Media Console Skill Level: Intermediate Tryde Media Hutch Following the great success of so many readers with the Tryde Collection, inspired by Pottery Barn s popular Hyde
More informationCopyright WilkerDos.com Dining Table. Project Designed By April Wilkerson - Plan Created By Jay Bates (jayscustomcreations.
Copyright WilkerDos.com 2017 Project Designed By April Wilkerson - Plan Created By Jay Bates (jayscustomcreations.com) Layout & Shopping List Page 2 of 12 Layout & Shopping List Item Quantity Description
More informationSilverware Chest Plan
Silverware Chest Plan 05L14.01 Introduction 1. Measure the space required for your cutlery before beginning this project to be sure that it will fit in the drawers and top compartment. The best way to
More informationDIY Wine Storage Cabinet
DIY Wine Storage Cabinet ADDICTED2DIY.COM *Before beginning this project, please read through all of the plans and the blog post. When building this project, be sure to measure your wood and cut to fit.
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 3
Kentucky 4H Wood Science Plans Notebook Plans Level 3 MATERIALS: 2 pieces wood 3/4 x 10 x 4 1 piece wood 3/4 x 12 x 4 2 pieces wood 3/4 x 3 x 2 5 1/2" 2 pieces wood 3/4 x 3 x 1 8 1 piece wood 2 x 4 x
More informationKreg Tool Co. All Rights Reserved.
Version 1 p. 1 Materials: Lumber: Qty: Board 2 2x2s 3 ft. long 2 1x2s 8 ft. long 2 1x3s 8 ft. long 6 1x6s 10 ft. long INSTRUCTIONS: Supplies: 1 1 / 4" Kreg Screws (coarse thread for softwoods, fine thread
More informationDisplay Case (for J&S)
Display Case (for J&S) This is constructed of maple plywood with solid maple (soft maple) edge banding. It was made to fit between a door and a kitchen cabinet, and has an elegant circular taper between
More informationMaterials. Special Tools and Techniques Chisel Long pipe clamps Miters Router with 1/2" rabbet cutter Rabbets Dadoes. Hardware
D esk Our executive desk was built with specific needs in mind. We wanted a large desktop, large drawers, and a cubbyhole to house a rollaway hanging file cabinet. We are thrilled with our finished project.
More informationBUILDING A STORM DOOR
BUILDING A STORM DOOR BY NEAL BARRETT Illustrations by George Retseck If you're in the market for a storm door, you probably know that there are many styles and models available. However, most of them
More informationjoining materials - wood
UNIT D E S I G N A N D M A N U F A C T U R E : C O U R S E M A T E R I A L Wood joints joining materials - wood The majority of joints used in woodcraft have been designed specifically to attain the maximum
More informationThe frame sections of the china hutch are assembled with the aid of glue and spiral dowels. Dowel centers are recommended to
60 CHINA HUNT 282 ARE YOU LOOKING for a showpiece china hutch to display your elegant chinaware, antique vase, or collectibles? Here's the perfect cabinet for you, with lots of transparent glass to show
More informationPROJECT PLAN TOOL CHEST
BUILD IT WITH ROCKLER PROJECT PLAN TOOL CHEST FEATURING ROCKLER S BUILD QUESTIONS? Go to www.rockler.com or call 800-279-4441 Stock # Item 63420 1/4" x 24" x 30" Baltic Birch Plywood 63446 1/2" x 24" x
More informationThis photo more clearly shows how locating pins are used to transfer the dowel holes from the edge to front of frame. Use bar clamps till glue dries.
CHINA HUTCH 266 The frame sections of the china hutch are assembled with the aid of glue and spiral dowels. Dowel centers are recommended to ease matching of dowel holes. gant chinaware, antique vase,
More informationAC50 Enclosure - Thin Edge
AC50 Enclosure - Thin Edge 2 3/16??? 4 PL 11/16 1 7/8 Piping Groove 2 7/8 Top thickness = 18mm 6 7/16 All other pieces thick Corner Radii and joints =?? Bracing blocks for back = 5/8 square, 2 ea. Back
More informationantebellum home in Eutaw, Alabama, built in 1860 (Google it for photos).
You Can Build the Kirkwood Bookcase By Jeff Branch A vid readers will tell you they often need a new way to store all of their books. I ve seen some pretty creative ways to stockpile books - in some instances
More informationModern Farmhouse Printer Cabinet. Addicted2DIY.com
Modern Farmhouse Printer Cabinet Addicted2DIY.com Before beginning this project please read through all of the plans as well as the blog post associated with this project. Always use safety precautions
More informationJewelry Cabinet. Materials: 5/8" brad nails 5-1" x 3" x 8' boards (or if not 2 1/2" wide. 1-4' x 8' sheet - 3/4" plywood. wood glue get 1x4's)
1 Jewelry Cabinet Materials: 1-4' x 8' sheet - 3/4" plywood 5/8" brad nails 5-1" x 3" x 8' boards (or if not 2 1/2" wide wood glue get 1x4's) sand paper 1-1" x 6" x 8' board wood filler 1/2 sheet - 3/16"
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 4
Kentucky 4H Wood Science Plans Notebook Plans Level 4 MATERIALS NEEDED: Note: 1" wood may be 3/4" thick and 2" x 2" may be 1 1/2" x 1 1/2" 2 pieces wood 1 x 3 x 17 1 piece wood 1 x 3 x 14 3/4" 2 pieces
More informationA Shaker Sewing Stand
America s leading woodworking authority Step by Step construction instruction. A Shaker Sewing Stand A complete bill of materials. Exploded view and elevation drawings. How-to photos with instructive captions.
More informationProject Skill Level: INTERMEDIATE Plywood Used: CANPLY EXTERIOR Good Two Sides (G2S) or precision sanded Aspen
Project Skill Level: INTERMEDIATE Plywood Used: CANPLY EXTERIOR Good Two Sides (G2S) or precision sanded Aspen MATERIALS LIST: (1) ¾" x 4 ft x 8 ft plywood panel (20) #8 x 2" Robertson or Phillips wood
More informationENJOY THIS SELECTION FROM. Woodworking 101. Includes Step-by-Step Instructions for 8 Projects. Woodworking
W ENJOY THIS SELECTION FROM Woodworking 101 Includes Step-by-Step Instructions for 8 Projects Woodworking 101 Aimé Fraser, Matthew Teague, and Joe Hurst-Wajszczuk To purchase your copy of Woodworking 101,
More informationKitchen Base Cabinet: Multiple Drawers Cabinets from Scratch
Kitchen Base Cabinet: Multiple Drawers by Cabinets from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for any loss, damage,
More informationBUTCHER BLOCK MICROWAVE OVEN STAND
BUTCHER BLOCK MICROWAVE OVEN STAND 828 The butcher block has fallen out of favor in recent years, replaced by the countertop cutting board in an attempt to save space. This design, however, makes the butcher
More informationPatio Table. Page 1 of 16
Patio Table www.andrewharriswoodwork.com Page 1 of 16 Introduction This plan makes a table that is unit which is 95 ½ inches long and 49 inches wide. The distance from the underside of the top edging to
More informationThis is a solid wood cabinet. The only plywood used is for the back and drawer bottoms.
Sideboard Sideboard Overview: This project requires basic woodworking skills and access to woodworking machines. Woodworking machines have sharp cutting edges and are NOT forgiving. You should be properly
More information10 Easy-to-Build. Plywood Projects
10 Easy-to-Build Plywood Projects Ten shop projects ten sheets of plywood. These rock-solid essentials take just a couple hours to build and will help you make the most of the space in your shop. All content
More informationULTIMATE ROUTER TABLE PLANS. By Dan Phalen
ULTIMATE ROUTER TABLE PLANS By Dan Phalen January 2017 Ultimate Router Table Plans. Copyright 2012-2017 by Daniel Phalen. Published by Creston Hall Publishing Company. All rights reserved. No part of this
More informationThe Q Frame PROJECT. a picture frame with secrets created exclusively for the Router Forum
The Q Frame PROJECT a picture frame with secrets created exclusively for the Router Forum 007 OR RELEASE FPLANS APPROVED The Q Frame: Project Overview LIST OF MATERIALS Frame Sides & Face 3/4 x 5 1/2 x
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 1
Kentucky 4H Wood Science Plans Notebook Plans Level 1 MATERIALS NEEDED: 1 piece wood 3/4" x 2 x 2 1 piece wood 3/4" x 3 x 3 1/2" 1 wooden spring-type clothespin 2-1 1/2" nails 1-1/2 woodscrew Wood Glue
More informationirdhouse Table Special Tools and Techniques Materials and Supplies Hardware
B irdhouse Table This whimsical table is one of our favorite projects, because it never fails to produce a smile on the faces of our backyard guests. Not only is it cheerful to behold but the glass top
More informationining Table Materials *Notes on Materials
D ining Table We looked around for the perfect table for the dining room. Some were too big, some too small, and most were just too expensive. So we built this one, and we are happy with the result. It
More informationKitchen Upper Cabinet: Single Door Cabinets from Scratch
Kitchen Upper Cabinet: Single Door by Cabinets from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for any loss, damage, disappointment,
More informationrmoire This attractive and practical two-door armoire takes up very little floor space in a bedroom but provides lots of storage. Because it is only
A rmoire This attractive and practical two-door armoire takes up very little floor space in a bedroom but provides lots of storage. Because it is only a little over 1 foot deep, it s easy to incorporate
More informationrmoire Materials Hardware
A rmoire No house ever has enough storage space, and I built this armoire to satisfy a couple of needs. Inside the armoire is a shelf large enough for the television. Under the shelf are six drawers that
More informationShoulder Plane. dovetailed. fine tools. Make an heirloom tool and learn the secret to creating double dovetails in metal it s easier than you think.
fine tools dovetailed Shoulder Plane Make an heirloom tool and learn the secret to creating double dovetails in metal it s easier than you think. I ve always been fascinated by old, metal hand planes.
More informationEmpire Dresser Plans
1 Empire Dresser Plans Materials 1 sheet 3/4" plywood (cabinet grade 4' x 8') 1 sheet 5 mm (3/16") underlayment plywood 4'x 8', buy another 1/2 sheet if you want to put a back on the dresser. 1-2" x 4"
More informationCorner Cupboard. This space-saving piece enhances any room 46 FINE WOODWORKING
Corner Cupboard This space-saving piece enhances any room BY G A R R E T T H A C K On every trip to the Shelburne Museum near Burlington, Vt., I visit a favorite object a small hanging corner cabinet.
More information(2) 4 x 8 Ft. Sheets of ¾-inch Purebond Plywood Tape Measure (2) 4 x 8 Ft. Sheets of ¼-inch Purebond Plywood Pencil (1) 1 x 8 x 8 Ft.
MATERIALS: TOOLS: (2) 4 x 8 Ft. Sheets of ¾-inch Purebond Plywood Tape Measure (2) 4 x 8 Ft. Sheets of ¼-inch Purebond Plywood Pencil (1) 1 x 8 x 8 Ft. Board Carpenter s Square (1) 1 x 6 x 8 Ft. Board
More informationSeascape Bungalow Assembly instructions. Laser Dollhouse Designs
Seascape Bungalow Assembly instructions Laser Dollhouse Designs NOTE: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also
More informationPROJECT PLAN OUTFEED TABLE
BUILD IT WITH ROCKLER PROJECT PLAN OUTFEED TABLE BUILD Stock # Item 00 ' Universal T-Track () 0 T-Track Intersection Kit 70 JIG IT Universal Drawer Slide Jig 0 " Drawer Slides () 77 Auto-Adjust Jig Clamp
More informationPROJECT PLANS MULTIPURPOSE WORK CENTER
R PROJECT PLANS MULTIPURPOSE WORK CENTER This handy project can provide the work space you need anywhere in your home. Whether you need that work space in the shop, the garage, the basement, or in a laundry
More informationYOU CAN BUILD THE JACKSON DRESSER. Combining traditional styling with rustic materials leads to a classic, yet casual look.
YOU CAN BUILD THE JACKSON DRESSER Combining traditional styling with rustic materials leads to a classic, yet casual look. Jeff Branch CONTENTS Jeff Branch Publisher: Jeff Branch Editor-in-Chief: Jeff
More informationA Contemporary Mobile File Cabinet. An elegant design that provides no-nonsense functionality.
A Contemporary Mobile File Cabinet An elegant design that provides no-nonsense functionality. A few years ago I built some office furniture for a local internet consulting company, and recently they called
More informationInstallation Guide. Pionite Decorative Surfaces One Pionite Road, Auburn, Maine PIONITE ( )
Installation Guide A Subsidiary of Panolam Surface Systems SMPBRO00-012 6/14 Pionite decorative laminates are designed for finished interior surfaces which require high impact, wear and stain resistance
More informationTraditional glass-pane and wood-muntin doors highlight this free-standing piece.
Bookcase Traditional glass-pane and wood-muntin doors highlight this free-standing piece. As the saying goes, there's nothing like good books. But they can present some storage problems--especially if
More informationDOCUMENT CHEST. Curly Maple, White Pine
25 DOCUMENT CHEST Curly Maple, White Pine 100 MAKING THE DOCUMENT CHEST After the stock has been thicknessed, ripped to width, and cut to length, plough a 1/4" X 3 /8" groove on the inside faces of the
More informationDIY Corner Bench with Built-in Table
DIY Corner Bench with Built-in Table Free woodworking plans for building a corner bench with a built-in table in the center. Cost: ~$75 Difficulty: Intermediate PINSPIRATION MOMMY 1 TOOLS AND SUPPLIES:
More informationMedia Center Woodworking Plans Our Home from Scratch
Media Center Woodworking Plans by Our Home from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for any loss, damage, injury
More informationTriple Bunk Staggered Beds [1]
Triple Bunk Staggered Beds [1] Submitted by jgbreeden [2] on Sun, 2013-06-23 21:38 [1] Summary: This Triple Bunk Bed, based on the Classic Bunk Beds, uses a staggered design to fit under common 8' ceilings
More informationCABINET INSTALLATION INSTRUCTIONS
CABINET INSTALLATION INSTRUCTIONS Please read these instructions through completely before beginning the installation. Thank you for choosing Plato Personalized Custom Cabinetry for your home. Your Plato
More informationENJOY THIS SELECTION FROM. Pocket Hole Joinery. Pocket Hole. Joinery Bookshelf Day bed Mirror/picture frame Dresser Bathroom vanity...and More!
t ENJOY THIS SELECTION FROM Pocket Hole Joinery Pocket Hole Joinery Bookshelf Day bed Mirror/picture frame Dresser Bathroom vanity...and More! Mark EdMundson To purchase your copy of Pocket Hole Joinery,
More informationCode Description Qty. Material Dimensions A Long Inner 4 2 x 4 pine 34-1/2 long
B utler s Chest Because it s designed to suit a variety of purposes, this butler s chest is a piece of furniture that absolutely anyone can appreciate. Used by itself, it can serve as an end table or can
More informationJeff Branch WOODWORKING YOU CAN BUILD A. By adding subtle design elements, a traditional furniture style becomes decidedly modern.
Jeff Branch WOODWORKING YOU CAN BUILD A By adding subtle design elements, a traditional furniture style becomes decidedly modern. Jeff Branch WOODWORKING Publisher: Jeff Branch Editor: Jeff Branch Art
More informationKitchen Base Cabinet: Single Drawer with Double Doors Cabinets from Scratch
Kitchen Base Cabinet: Single Drawer with Double Doors by Cabinets from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for
More informationKitchen Step Stool. Premium Plan. In this plan you ll find: America s leading woodworking authority
America s leading woodworking authority Premium Plan In this plan you ll find: Step-by-step construction instruction. A complete bill of materials. Construction drawings and related photos. Tips to help
More informationTools: Drill/Driver Kreg Jig Miter Saw Jigsaw Circular Saw Adjustable Square Tape Measure Veneer Trimmer Sandpaper and Sander
R PROJECT PLANS DROP-FRONT DESK Create a workspace almost anywhere with this drop-front desk. Mounted to a wall, it doesn t take up any floor space, which means you can hang it wherever you need to work.
More informationKitchen Upper Cabinet: Double Doors Cabinets from Scratch
Kitchen Upper Cabinet: Double Doors by Cabinets from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for any loss, damage,
More informationwoodworkersjournal.com MATERIAL LIST
MATERIAL LIST T x W x L 1 Legs (2) 1 1 2" x 3 1 2" x 36 7 16" 2 End Uprights (2) 1 1 2" x 3 1 2" x 32 1 2" 3 Stringers (4) 1 1 2" x 3 1 2" x 42" 4 Top Cladding, Long (2) 3/4" x 7 1 4" x 65 3 4" 5 Side
More informationModular ottoman. assembly instructions
Modular ottoman assembly instructions Smooth & Wrinkle-Free Fabric Covers: In addition to these printed instructions, you may want to watch our beauty tips videos on the customer service page of our website.
More information!! " # $ % & '! ( ) * +, -
!! " # $ % & '! ( ) * +, - North Pegasus This carton contains: (1) Instruction package. Response Curves North Creek Cabinet Handbook North Creek Wiring Guide (2) 6 oz. Rolls of Dacron stuffing. (1) Tube
More informationThe Universal Table Saw Sled
The Universal Table Saw Sled Do Precision Work Even with Inexpensive Table Saws! Table saw blades always tend to move the wood while the cut is being made. This is why it's so difficult to get accurate
More informationMaking a Massive Bookcase Step-by-Step
Making a Massive Bookcase Step-by-Step Jeff Branch WOODWORKING The only thing challenging about this project is its huge size. By JFF BRANCH A t right is a rendering of my first woodworking project completed
More informationDIY Farmhouse Cabinet
DIY Farmhouse Cabinet Addicted2DIY.com *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever
More informationMITER SAW SUPPORT WINGS PLAN
MITER SAW SUPPORT WINGS PLAN Version 1.0 How to build support wings for your miter saw With easy to follow step-by-step instructions, you will be able to cut, assemble, and finish your very own support
More informationWays to get the most out of your
5 Ways to get the most out of your router table When you mount a router on a table, you expand your shop s potential. To help you take advantage of this potential, we assembled five router table techniques
More informationLARGE PLYWOOD CUTTING GUIDE
Copyright 2015 Shanty-2-Chic.com Workbench I f you are tight on space but large on ideas this bench is just what you need. Sturdy and mobile this bench has an ingenious fold out wing that gives you over
More informationChester - Solid Pine Desk
Chester - Solid Pine Desk ssembly Instructions- Please keep for future reference 89/600 18/812 Dimensions Width - 120cm Depth - 50cm Height -,cm Important Please read these instructions fully before starting
More informationHardware Cabinet. Part 3
Hardware Cabinet Part 3 The vertical dividers are the next task on the cabinet and a bit of a trick to get right. The horizontal dividers are only ½ thick pine spanning the 31 width of the cabinet and
More information