Jet-ski with motor boat engine
|
|
- Neal Singleton
- 6 years ago
- Views:
Transcription
1 Tools required: Vice with bending support Wood glue (water resistant) Scissors Ruler Pencil Round file ø2 ø3 ø4 Drills Jigsaw Sandpaper Super glue Please Note The OPITEC range of projects is not intended as play toys for young children. They are teaching aids for young people learning the skills of Craft, Design and Technology. These projects should only be undertaken and operated with the guidance of a fully qualified adult. The finished projects are not suitable to give to children under 3 years old. Some parts can be swallowed. Danger of suffocation! Engineer s file Soldering iron Metal cutters Phillips screwdriver Adhesive tape Content Quantity Dimensions( mm) Designation Part no. Hull 1 280x100 Hull 1 Plywood 2 300x210x3 Base & individual parts 2 Wooden bar 2 250x5x5 Frame 3 Wooden bar 1 50x10x5 Engine bracket 4 Aluminium sheet 1 200x200x0,3 Aluminium parts 5 Brass pipe 1 ø3x100 Brass pipe 6 Round brass bar 1 ø2x245 Round brass bar 7 Propellor (clockwise-turning) 1 Propellor 8 Wire connectors 1 Fastening rudder 9 Washers 12 7/3,2 Fastening rudder 10 Silicon tube 1 1/3 Connection motor & shaft 11 Mounting bracket 1 ø21 Engine fastening 12 Motor 1 Motor 13 1
2 Content Quantity Dimensions( mm) Designation Part no. Wire, red 1 Cabling 14 Metal axle 1 ø3x70 Fastening rudder 15 Phillips metal screw 2 2,9x13 Fastening 16 Cylinder head bolt 1 25xM3 Fastening 17 Cap nut M3 1 Fastening person 18 Cylinder head bolt 2 3x6 Fastening 19 Battery holder 1 Battery holder 20 Rocker switch 1 15x10,5 Switch Drill holes ø 3mm x 5x Draw a 5mm rim round the hull (1) and cut off any excess material. Measure and centre 2 drill holes at the stern of the hull and drill two ø 3mm holes. Attach the wire connectors (9) with 5 washers (10- upper screw), 4 washers (10- lower screw) and 2 screws (19). Do not tighten just yet. 3 4 ø4 ø3 c I A F D J E L G K H M B Glue the template for the individual pieces (pages 9+11) together and glue to the plywood (2). Drill the ø 4mm holes and saw out all pieces as accurately as possible. Tidy up the sawn edges with sandpaper. 2 Glue the template (page 7) on to the second piece of plywood (2), drill a ø 3mm hole and cut out. Tidy up the sawn edges with sandpaper.
3 5 6 H 5a E A C B 5b I 5c Glue the template (page13+15) together, copy on to the aluminium sheet and cut out the individual parts with metal cutters. Clean up the edges with an engineer s file. Glue the individual pieces A, B,C,E, H + I together as shown. Let the glue dry properly. 7 D F G 8 5a J K L Glue parts E,F,G together as shown. Let the glue dry properly. Then connect both arms (L+K) and the head to the body (J) using the screw (17), the washers (10) and the cap nut (18)! Using super glue, stick the piece of aluminium (5a) to the top as shown, one piece at a time. Then cut off the excess with the metal cutters and file the edges flush b 7 6 Bend the aluminium parts (5b) on one end approx.15mm by 90 and fit in. Cut off the excess at the end and deburr the edge. Glue in with super glue to create the seat as shown. Shorten the brass bar (7) to 115mm and deburr properly. Deburr the brass pipe (6) as well. Insert the bar to test whether it works. Add the propeller to one end. 3
4 11 12 ø3 15 5c Drill a hole (ø3 mm) in the bottom of the hull, 75mm away from the edge of the stern. File it with the a round file until the brass pipe can be glued into its future position without tension. Shorten the metal axle (15) to approx. 40mm. Wrap the rudder (5c) around the axle as shown above and glue it on. Then insert into the wire connectors (9) and tighten the screws. For measurements see point 11! positive pole mm Pull the silicon tube (11) over the motor shaft. Screw the motor (13) with the mounting bracket (12) and the metal screws (16) to the wooden bar (4). Strip the insulation from both sides of an approx. 120mm length of wire (14) and connect one end to the positive pole of the motor (marked red). Connect the black cable from the battery holder to the negative pole of the engine. Fit the unit to the hull in such a way, that the motor axle can be connected to the round brass bar through the silicon tube (11). Glue the motor in place with super glue. Align the pipe with the axle and glue in place (see illustration point 11), using 2 component glue! Make sure that the propeller can rotate M Centre the deck (M) and glue to the hull (1) with super glue. Measure and build a frame for the deck opening from the pine bars (3), fit into the deck opening and glue in, so that the strips protrude over the deck by 2mm. 4
5 16 17 Fit the switch (22) into the designated opening in the construction as shown. Connect the red cable from the battery holder to the central switch connector. Connect the red cable from the motor (13) to the outer switch connector. Then insert the batteries and place the top of the jet-ski on to the frame in the deck. 18 Place the figure you constructed in point 7 on the jet-ski and it s all done! 5
6 6
7 Template Scale 1:1 7
8 8
9 Template individual pieces Scale 1:1 Dividing line 9
10 10
11 Template individual pieces Scale 1:1 Dividing line 11
12 12
13 Template aluminium sheet Scale 1:1 Dividing line 13
14 14
15 Template aluminium sheet Scale 1:1 Dividing line 15
Celtic door harp Necessary tools:
.004 Celtic door harp Necessary tools: Fretsaw Drill ø/5mm Sandpaper/ file Wood glue Side cutters Pencil,ruler Scissors Bradawl Double sided tape Machine vice Please Note The OPITEC range of projects is
More informationVehicle with robotic arm
1 0 6. 2 0 2 Vehicle with robotic arm Please Note The OPITEC range of projects is not intended as play toys for young children.they are teaching aids for young people learning the skills of Craft, Design
More informationPremium-Line Solar-Motor
11.727 PremiumLine SolarMotor Necessary tools: Please Note The OPITEC range of projects is not intended as play toys for young children. They are teaching aids for young people learning the skills of Craft,
More informationSavonius Wind Generator
114.664 Savonius Wind Generator The OPITEC handicraft packs are not toys in a typical offthe-shelf sense, but rather additional teaching and learning material for educational purposes. This craft pack
More informationThermo fan. Important Notice:
105.434 Thermo fan Important Notice: Beware of fire, never leave a burning candle unattended!! Please Note The OPITEC range of projects is not intended as play toys for young children.they are teaching
More informationMetal steam roller. Necessary tools. Parts list
10.15 Metal steam roller Please Note The OPITEC range of projects is not intended as play toys for young children.they are teaching aids for young people learning the skills of Craft, Design and Technology.These
More informationChopper Motorcycle. Warning! This product contains small parts that can be swallowed. There is a danger of choking E101980#1
1 0 1. 0 Chopper Motorcycle Please Note The OPITEC range of projects is not intended as play toys for young children.they are teaching aids for young people learning the skills of Craft, Design and Technolo-
More informationReed Contact-Motor
105.10 Reed Contact-Motor Please Note The OPITEC range of projects is not intended as play toys for young children.they are teaching aids for young people learning the skills of Craft, Design and Technolo-
More informationʻ L e o n a r d o d a V i n c i ʼ s gear machineʼ
1 0 0. 9 1 7 ʻ L e o n a r d o d a V i n c i ʼ s gear machineʼ Autore Covolan Girolamo Please Note The OPITEC range of projects is not intended as play toys for young children.they are teaching aids for
More informationWater Wheel. Autore Covolan Girolamo
1 0 0. 9 0 6 Water Wheel Autore Covolan Girolamo Please Note The OPITEC range of projects is not intended as play toys for young children.they are teaching aids for young people learning the skills of
More informationCompass with sundial
115.420 Compass with sundial Necessary tools: Scissors Craft knife Pencil + ruler Fretsaw Hammer Wood glue All purpose glue Sandpaper Please Note The OPITEC range of projects is not intended as play toys
More informationPremium-Line "Water pump"
111.471 Premium-Line "Water pump" Necessary tools Fresaw or hacksaw Pillar drill Screwdriver llen keyl M3 Drills ø3, 3,, 6, 6, mm Scriber Emery cloth, file Oil for drilling acrylic ll purpose Hammer Please
More informationCorvus Racer CC
Corvus Racer 540 35CC Item No:L-G035008 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio mm mm 1200sq in (77.4sqdm) 9.9-12lbs(4.5-5.5kg) 91-1.20(2C) 1.10-1.40(4C) 20-40cc
More informationTOYOTA MOTOR EUROPE CA Products Division Tel : Fax :
TOYOTA MOTOR EUROPE CA Products Division Tel : + 32 2 745 26 77 Fax : + 33 2 745 26 99 Ordering part numbers Comments Part Numbers Wooden floor one hatch PZ449-D3C42-11 one hatch with carpet PZ449-D3C42-01
More informationCitabria Pro. Aerobatic Parkflyer. by Joel Dirnberger
Citabria Pro Aerobatic Parkflyer by Joel Dirnberger Revision C: December 21, 2004 Citabria Pro Building Instructions Length: Wingspan: Wing Area: Flying Weight: Wing Loading: Functions: Specifications:
More informationSpeedboat with wind up motor
109.427 Speedboat with wind up motor Note The OPITE range of products is not primarily intended as toys for young children.it is for teaching, designing and making to ensure that pupils experience a range
More informationTECHNICAL FILE FOR THE STIRLING ENGINE
TECHNICAL FILE FOR THE STIRLING ENGINE FABRICATION RANGE ELEMENT: Support ring SET: Stirling engine RANGE: 1 SHEET: 1 of 1 DRAWING: N 11 MATERIAL: white NUMBER: 1 PVC N o PHASE, SUB-PHASE OR 10 MAKING
More informationReady To Go SimpleSpec tm. Installation Manual. For more information, please visit 3-form.com or call
Contents Overview ( 1) 3/8" Varia Panel = Cable Tensioner with Cover Plate KIT Stainless Steel: 3-15-1636-K Black Oxide: 3-15-2005-K Cable Tensioner with Cover Plate SS: 3-15-1636 BO: 3-15-2005 + M8 Thread
More informationRESolution V2 Manual
RESolution V2 Manual Note for the German Manual: Yellow Bottle thick CA Pink Bottle Med CA Blue tube 5 minute Epoxy Green tube 90 Minute Epoxy Construction of the Fuselage Step 1: Cover the plan with a
More informationLED-Reading lamp Metal
111.264 LED-Reading lamp Metal Necessary tools: Metal drills ø2,/3/4/6 mm Thread Tap M3mm 90 -Countersink Fretsaw with blade for metal File assortment Vice with jaw protectors Pencil Ruler Soldering iron
More informationPneumatic Robot arm/digger
1 0 6. 1 8 6 Pneumatic Robot arm/digger Please Note The OPITEC range of projects is not primarily intended as toys for young children. It is for teaching, designing and making to ensure that pupils experience
More informationEdge 540 V3 35CC. Scheme A. Item No:L G Specifications. Flying Weight
Edge 540 V3 35CC Item No:L G035016 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio Description 76 (1930mm) 74 (1879mm) 1200sq in(77.4sqdm) 9.9 12lbs(4.5 5.5kg) 91 1.20(2C)
More informationSuper Sky Surfer 2000 Assembly Instructions
Super Sky Surfer 2000 Assembly Instructions Note: Plug and Play version of the Sky Surfer comes with fuselage pre-glued and motor/servos installed. If you wish to route antennas or wires through the tail,
More informationTechnicians of Terror. This is the air valve we make to use with our air
These are pictures of our scissor prop. Technicians of Terror http://www.halloweenfear.com/scissorprop.html props. This is the air valve we make to use with our air This pictures the duel door closer cylinders
More informationCheeper Assembly instruction
1. Equipment, materials and tools for assembly.......2 2. Assembly.....3 3. Setting of the model.....11 1. Equipment, materials and tools for assembly 1 Wing; 2 Fuselage; 3 Stabilizer; 4 Fin; 5 Dowel for
More informationAssembly Instructions. Important!
Play Action Spiral Tube Slide Assembly Instructions Important! Intended for residential use by children ages 2 to 10, only on properly installed PlayStar playsets. Before use refer to complete safety guidelines
More information43in EPP Acrocub Instruction Manual
43in EPP Acrocub Instruction Manual Specifications Wingspan: 43.3in (1100mm) Length: 41.3in (1050mm) Flying Weight: Approx. 1.5lb (670g) Dear Customer, Congratulations on your purchase of 43in EPP Acrocub
More informationThe Mind Project s Iris 1 Robotic Arm. Assembly instructions Step 1
The Mind Project s Iris 1 Robotic Arm Assembly instructions Step 1 Packing list Below you will find pictures and descriptions of each part. It may be helpful to take each piece out of the bag and place
More informationMXS R 30CC. Item No:L G Specifications. 67 1/2"(1720mm) (2C) (4C) 26 35cc gas DLE 30/35RA MLD35 JC30Evo.
MXS R 30CC Item No:L G030008 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio Description Covering Material Carbon Fibre : 75"(1915mm) 67 1/2"(1720mm) 1023sq in(66sq
More informationTECHNICAL FILE OF THE REED SWITCH MOTOR (RSM)
TECHNICAL FILE OF THE REED SWITCH MOTOR (RSM) TABLE OF CONTENTS 1. Nomenclature of the RSM 2. Rotor template 3. Fabrication of the base of the motor 4. Fabrication of the rotor shaft brackets 5. Fabrication
More informationTOOLS REQUIRED Metal Wood Wood and Metal Screws. #16 Drill #12-24 Tap. 1/8 Drill
DEVICES COVERED IN THIS DOCUMENT: 4700S Surface Vertical Rod Device 4700SF Fire Exit Surface Vertical Rod Device TOOLS REQUIRED Metal Wood Wood and Metal Screws Sex Bolts #7 Drill ¼ -20 Tap #16 Drill #12-24
More informationIDR assembly instructions:
IDR assembly instructions: Required Tools: 2 X 12mm Open End Wrench 14mm open end wrench #2 Phillips Head Screw Driver (Drill with adjustable torque clutch recommended) 8mm nut driver (Supplied in IDR-AK)
More informationSellotape Dispenser E112134#1
2. 4 Sellotape Dispenser Please Note The OPITEC range of projects is not primarily intended as toys for young children. It is for teaching, designing and making to ensure that pupils experience a range
More informationBuilding Instructions Diva cabin boat
Building Instructions Diva cabin boat Order no. 3093/00 aero-naut Modellbau Stuttgarterstr. 18-22 D-72766 Reutlingen / Germany http://www.aero-naut.com 1 For pictured building instructions please see the
More informationINSTRUCTIONS for fire lamps 1-8
INSTRUCTIONS for fire lamps 1-8 1. Lamp from wooden pen holder: Material used: Article Number Quantity:: Pendant lamp holder, 100cm lamp cable with ceiling rose and pendant lamp holder 116013 1 Wooden
More informationThe Useless Machine. Parts Only - Build Guide v0001
TM The Useless Machine Parts Only - Build Guide v0001 For the best outcome, follow each step in order. We recommend reading this guide entirely before you get started. Tools required: One phillips screwdriver,
More informationWritten By: Brook Drumm
Simple 1401 Assembly For kits produced between 1/15/14-6/1/14. This guide is for kits with the Fan Shroud. Instructions for metal and wood extruder (and bed) included below. Written By: Brook Drumm TOOLS:
More informationEPPA2-KIT DUAL MONITOR ARM CONVERSION
EPPA2-KIT DUAL MONITOR ARM CONVERSION EPPA2-KIT Rev A 10/17 Model EPPA2-KIT-XXX ASSEMBLY AND ADJUSTMENT EPPA2-KIT PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment
More informationADULT. Adirondack / Muskoka Chair Plans
ADULT Adirondack / Muskoka Chair Plans Materials List 3/4" x 9 1/2" (1.9cm x 24.1cm) redwood, cedar or pine boards. Six, 8' (2.44m) boards should make one chair depending on knots and layout. You can also
More informationLANDING GEAR. 1. Fit landing gear into slots on bottom of fuselage.
LANDING GEAR 1. Fit landing gear into slots on bottom of fuselage. 4. Use channel-lock pliers to press blind nuts into position (note: drilled hole should be slightly smaller than shaft of blind nut for
More informationPrepare Base Assembly. (If pump is pre-assembled on base, go to step#8.)
F L Instructions Maxim 3000 Turbo Flush Installation INTRODUCTION Satellite portable restrooms and accessories must be assembled according to approved assembly procedures. Avoid variations in assembly
More information(Build Instructions)
(Build Instructions) Specifications * Wingspan: 58cm * Length: 50cm * Flying Weight: 59 grams * Channels: 3 (Rudder Elevator Throttle) * Suggested Receiver: 4Ch Micro * Motor: 8mm GearDrive * Prop: GWS
More information/ Rudder Installation Guide
/ Rudder Installation Guide Parts List Part # Part Description Qty Part # Part Description Qty 1030 Plastic Bead 1 1195 Rope; 1/8" Black Nylon 1 @ 9 1044 1/4-20 x 5/8" Pan Head Bolt 2 1353 Sliding Track
More informationCONTINUED. TABLE TOPS: 1. Sort one 2x6x8 piece from your lumber. 2. Measure and mark two 48 pieces from each, then cut.
# Materials: Quantity Each: Total Quantity: x4x8 7 x6x8 1 TIPS FOR SUCCESSFUL PREP WORK: Before starting, carefully read through the entire instruction sheet. Refer to the material list to the left and
More informationCabinet Mount Lifter Instructions
PART LIST 2 @ Side Pivot Arms 1 @ Coupler Tube 1 @ Left Hand Bracket 1 @ Right Hand Bracket 2 @ Cover Support Arms w/ Foam Grip 1 set of Cover Saver 4 @ 4 Wood Screw 8 @ 1 Wood Screw 12 @ 1 Black Tek Screw
More informationTin Lizzie 18 Assembly Instructions
Tin Lizzie 18 Assembly Instructions Revision: 07/29/16 Table of Contents Aides 3 Before You Begin 5 Aides 5 Tools 6 Perfect Stitch Parts 2 12 Modify the Machine 12 Prepare Drill Templates 12 Front Display
More informationTraditional Undermount: S Method (Undermount):
TOOLS REQUIRED 15.1 TOOLS REQUIRED The installation of Corian shape product must be a precise and exacting process to ensure that a good fit is always created. Using the correct tools is essential. In
More informationWallbeds Northwest ENDURA CABINET PLANS AND INSTRUCTIONS
Thank you for purchasing your Wall Bed from Wallbeds Northwest. If you have purchased a complete "Endura DIY Kit," then much of the work is already done for you. Please skip to assembly instructions. Note
More information4600 Series Rim Narrow Stile Exit Device Installation Instructions I-ED01162
DEVICES COVERED IN THIS DOCUMENT: 4600 Series Rim Panic Narrow Stile Exit Device 4600 Series Rim Fire Narrow Stile Exit Device OVERVIEW Outside of Door RHR LHR Inside of Door APPLICATIONS 4950 BLADE STOP
More informationPARTS INCLUDED IN FIXED STAIR CABLE RAIL KIT:
175 SERIES FIXED STAIR CABLE RAIL - INSTALLATION INSTRUCTIONS PARTS INCLUDED IN FIXED STAIR CABLE RAIL KIT: FIXED STAIR TOP RAIL (1) A FIXED STAIR BOTTOM RAIL (1) B D UPPER SADDLE BRACKET (1) C BRACKET
More informationInterior CHAPTER 21. Phantom Roadster Instruction Manual 273
CHAPTER 21 Interior When you get to this chapter you are now starting on the finish that will make your car one that will be complete your hard work. This chapter will cover the installation of the door
More informationAssembly Instructions
Assembly Instructions Note: Prior to assembly, be sure to remove all printing pads from the printed parts and also be sure to sort through and organize all of your hardware before assembly this will help
More informationWind Turbine Experimenter s Kit User Guide
Wind Turbine Experimenter s Kit User Guide 42284 V0116 Cautionary and Warning Statements This kit is designed and intended for educational purposes only. Use only under the direct supervision of an adult
More informationInstallation Instructions for. Before You Begin TOOLS REQUIRED
Composite Railing System STEP-BY-STEP Installation Instructions for Spectrum Composite Railing Virtually maintenance free 20-year warranty EverNew Spectrum Railing system is designed to work with a number
More informationC-180 Builder s Manual
C-180 Builder s Manual. May 20, 2002 Last revised July 11, 2002 Copyright! 2002 Douglas Binder, Mountain Models www.mountainmodels.com sales@mountainmodels.com (719) 630-3186 1 Required Equipment! Xacto
More informationBT-55 KIT # Ebay Parts List P/N Description Qty. Fits diameter rockets (33mm or BT-55)
KIT #10543 BT-55 Ebay Parts List P/N Description Qty 15403 33mm Ebay Laser-cut Sheet 1 13016 AC-33 (single) 1 13004 33mm Coupler with hole 1 10129 AT-33mm/2 with hole (for Ebay) 1 13066 Weld Nut for Rail
More informationSport-Thieme Handball Goal, 3x2 m, Free-Standing or socketed
Assembly instructions Art.-Nr.: 201 0915 203 4502 Sport-Thieme Handball Goal, 3x2 m, Free-Standing or socketed 0218214 2018 Sport-Thieme GmbH D-38367 Grasleben Germany sport-thieme.com info @sport-thieme.com
More information105" TIGER MOTH ARF INSTRUCTION MANUAL VERSION 1.0
105" TIGER MOTH ARF INSTRUCTION MANUAL VERSION 1.0 Step 1. Installation of the aileron servos 1) Mount aileron servo to servo mounting blocks with servo s screws. Install servo mounting plate with screws.
More informationAssembly Instructions. Important!
Play Action Spiral Tube Slide Assembly Instructions Important! Intended for residential use by children ages 2 to 10, only on properly installed PlayStar playsets. Before use refer to complete safety guidelines
More informationName Standard or Description QTY.
Part List Part Number Name Standard or Description QTY. 1 Base - 1 2 Nut Hexagon Nut ISO - 4032 - M3 19 3 Motor/Encoder Assembly Mabuchi RS-645VA and Encoder 1 1 4 M3x10 Screw ISO 7045 - M3 x 10 2 5 Steel
More informationELECTRIC RACER BASIC BUILD
Page 1 Name: Set: Date: This guide will take you through the process of creating a basic electric racer. After you finish this build, you should be able to experiment, design and engineer your own racer.
More informationSpiderbeam Balun Construction Guide
BALUN CONSTRUCTION GUIDE Ver. 1.0 1 The components of the Balun Kit are in a plastic bag. Most of the components are inside the plastic case of the balun. The aluminum U-profile and the RG-142 Teflon Coax
More informationDresser. Materials & Tools FEATURING FORMALDEHYDE-FREE TECHNOLOGY. Free Plans to build a Dresser
Free Plans to build a Dresser Materials & Tools Materials: 1-1/4 pocket hole screws 1-1/4 brad nails 3 sets of 18 drawer slides Drawer pulls Edge banding, optional Wood glue Sandpaper (100, 150, 220 grits)
More informationHawko LED Flex & Accessories Installation Instructions
LED Flex & Profiles Hawko LED Flex & Accessories Installation Instructions Contents Installation of IP20 LED Flex 4 Installation of IP67 LED Flex 6 Mounting Channel Installation 8 Mounting Clip Installation
More informationGeneral Prisoner Transport Install Instructions PT-2-INST
General Prisoner Transport Install Instructions PT-2-INST 50 or 60 high x 80, 100 & 120 inch long / Double Compartment Inserts Also refer to PT-A-3XX instructions for vehicle specific mounting measurements
More informationWARNING! ETCHED PARTS CONTAINED IN THIS KIT HAVE SHARP POINTS, EDGES AND CORNERS.
MPD18 chassis build instructions K A (see below for details) J I G H L C D F E B M Parts list: Ident Quantity A Etched Nickel/Silver fret 1 B Wheel sets 2 C Worms 2 D Worm gears 2 E Shaft adapters 2 F
More informationAUTOMATIC ADVANCE MANUAL
AUTOMATIC ADVANCE MANUAL AVL Looms, Inc. 3851 Morrow Lane, Suite #9 Chico, CA 95928-8305 530 893-4915 530 893-1372 fax # info@avlusa.com www.avlusa.com Copyright 2009 TABLE OF CONTENTS Page # I. Parts.........................
More informationInstallation for Full Size Polaris Ranger Crew Doors
Installation for Full Size Polaris Ranger Crew Doors Order of Installation: Heater Doors Wiper on to Windshield Windshield Top & Back Panel Note: Most of the steps in these instructions need to be repeated
More informationThe Useless Machine. DIY Soldering Edition. Instruction Guide v0004
The Useless Machine DIY Soldering Edition Instruction Guide v0004 TM For the best outcome, follow each step in order. We recommend reading this guide entirely before you get started. Tools required: Soldering
More information1.9 KIT # Fits Aerotech 1.9 diameter rockets. Uses coupler and payload tube included with select Aerotech Kits. Ebay Parts List Description.
KIT #0545.9 Fits Aerotech.9 diameter rockets. Uses coupler and payload tube included with select Aerotech Kits. Ebay Parts List P/N Description Qty 5405.9 Ebay Laser Cut Sheet Thin 5406.9 Ebay Laser Cut
More informationTRUE TECHNICAL SERVICE MANUAL - ALL MODELS. DOORS/DRAWERS/LIDS
DOORS/DRAWERS/LIDS 55 56 NOTES DOORS/DRAWERS/LIDS Swing s 73 74 NOTES INSTALLATION OF A GDM-SWING DOOR Phillips Head Screwdriver (2) - 1/8" Drift Punches (forged) Top Bracket NOTE: It may be necessary
More informationSwingSafe Swing-Away Mailbox Support Diagram
SwingSafe Swing-Away Mailbox Support Diagram Wood Mounting Plates Top Arm (B) Muffler Clamps (A) Carriage Bolts and Nuts Bottom Arm 4-Foot U-Channel Post USPS Recommended 42-44 Height Ground Slope Hex
More information12. Wings, Flaps, Ailerons and Struts
12. Wings, Flaps, Ailerons and Struts Fit Aileron Hinges Reference: Drawing 20270K2 Photo 12.1 Parts Required: 2007092 Aileron LS 200809N Aileron RS 2001394 Hinge 3/16 A1 (4) 2001694 Hinge Pin (4) PH0059N
More informationNew Jersey Electric Guitar DIY Kit
New Jersey Electric Guitar DIY Kit Thank you for purchasing this DIY Guitar Kit. The following instructions specify how to assemble your guitar. There are a variety of finishes that can be applied to the
More informationInstallation Instruction
Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry
More informationBaby Grande or Grande Crank Shade with Cables and Housing Installation Instructions
Baby Grande or Grande Crank Shade with Cables and Housing Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit Screwdriver (Flat & Phillips) Measuring Tape Pencil 4 Level Plumb Line ¼ Masonry
More informationPanavia TORNADO F 3. Electric fan powered model. Producer: Jiri Bacinsky
Panavia TORNADO F 3 Electric fan powered model Producer: Jiri Bacinsky Panavia TORNADO F3 is model for experienced modellers. It requires fast reactions and slow heart rate. Model is powered by ducted
More informationINSTALLATION INSTRUCTIONS LARGE FLAT PANEL IN WALL ENCLOSURE Model: PAC-500
INSTALLATION INSTRUCTIONS LARGE FLAT PANEL IN WALL ENCLOSURE Model: PAC-500 Specifications: Designed for in-wall installation spanning a minimum of 3 wood studs, 16" on center. Accomodates MWR, PWR and
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationHigh performance 90mm fiberglass jet
High performance 90mm fiberglass jet Assembly manual For intermediate and advanced fliers only! Specs Wingspan: 1255mm Fuselage length: 1250mm Flying weight: 2600-3000g Wing area: 22.6 dm² Wing loading:
More informationEND FRAMES. End frames built using pressure treated 2x4 (1 1/2" x 3 1/2") 36" 34" 7/16" pilot hole. 5 1/2" x 1/2" lag bolt 8" wheel 23"
END FRAMES End frames built using pressure treated 2x4 (1 1/2" x 3 1/2") 23" 17 1/2" (B) (B) Measure from the bottom of your stone to 1" below the lip to get your measurement. 17 1/2"(B) 36" 34" 1/2" flat
More informationBushwacker Jeep Flat Style Fender Flares Front Pair
Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:
More informationFortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.
Installation Instructions for FortressCable H-Series Stair Panels with Simplified Stair Bracket SSB-05 and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and
More informationAssembly Instructions
Assembly Instructions Note: Prior to assembly, be sure to remove all printing pads from the printed parts and also be sure to sort through and organize all of your hardware before assembly this will help
More informationINSTALLATION INSTRUCTION RRU DOUBLE LIGHT POLE MOUNT
INSTALLATION INSTRUCTION RRU Double Light Pole Mount for installation of two RRU units on mast, towers or other vertical structures. CUE DEE YOUR INNOVATIVE PARTNER 1 CONTENTS 1. PRODUCT COVERED IN THIS
More informationMounting Accessories. Installation Guide. VIVOTEK SD83XXE Speed Dome
VIVOTEK SD83XXE Speed Dome Mounting Accessories AM-116/117 Pendant Pipe AM-118 Pendant Head AM-221 Gooseneck AM-231 Parapet Mount AM-519 Pendant Adaptor Installation Guide Corresponding part numbers: AM-116:
More informationCOWO. Customer Wall Outlet. 1 General. 2 Kit content. 3 Handling of the box. TC-1203-IP Rev A, Apr
COWO I N S T A L L A T I O N I N S T R U C T I O N TC-1203-IP Rev A, Apr 2017 www.commscope.com Customer Wall Outlet 1 General Customer Wall Outlet 2 Fiber for max. 2 bend reduced fibers, 2 SC-adapters
More informationPORTA-DOCK, INC. AP17 APD DS 4 X 16 T12 AW17 CPD DS 4 X 16 T12
Page 1 of 7 PORTA-DOCK, INC. AP17 APD DS 4 X 16 T12 AW17 CPD DS 4 X 16 T12 *For Beige Decking Add the Letter B to Model* Thank you for purchasing out product! *Please read these instructions and follow
More informationSE5a Instrument Board part 2 - rev 1.1
SE5a Instrument Board part 2 - rev 1.1 Fuel (Petrol) Valve This valve uses two circular name plates, eight brass screws, one black plastic base, copper wire and two black plastic risers. You can pick any
More informationHARDWARE KIT # KKM or Rear Compartment: (Some hardware not used in all applications)
PRISONER TRANSPORT INSTRUCTIONS for CHEVROLET EXPRESS VAN PT-C01-100-2A TOOLS REQUIRED: Standard and Metric Socket Sets Awe or Scribe Tape Measure Impact Gun (recommended) Pry-bar Caulk gun Drill & drill
More informationRugged Ridge Body Armor Guard Kit, 5 Pieces, Black (07-Current JK 4-door)
Rugged Ridge Body Armor Guard Kit, 5 Pieces, Black (07-Current JK 4-door) Installation Time: 60 Minutes Tools Required: Notes: Phillips head screwdriver 3/8 socket or Flat head screwdriver 1/2 socket 7
More informationThe Mind Project s Iris 1 Robotic Arm. Packing List Assembly instructions
The Mind Project s Iris 1 Robotic Arm Packing List Assembly instructions Packing list Below you will find pictures and descriptions of each part. It may be helpful to take each piece out of the bag and
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS GLI POOL PRODUCTS / 1100 PERFORMANCE PLACE / YOUNGSTOWN, OH 44502 PH. 800-448-2343 FAX 330-744-1228 www.glipoolproducts.com WARNING THERE IS NO SUBSTITUTE FOR COMPETENT ADULT
More informationObtained from Omarshauntedtrail.com
DaveintheGrave's Halloween Props Animated Crawling Skeleton Build a life-size skeleton torso that realistically crawls across the lawn one arm at a time. 1. Motor Base and Linkage Assembly BASE - I used
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationV4 Premium Kit. Prusa i3 Build Guide
V4 Premium Kit Prusa i3 Build Guide Hi! Congratulations on your purchase of the DIYElectronics.co.za Prusa I3 kit, the best South African 3D Printer Kit! Hopefully this should serve as complete guide to
More information-1- Coach Instructions.
-1- Coach Instructions. Insert the bogie pivot pins through the bottom of the coach body ensuring the dimples fit into the recesses. Glue the.06 x.25 short strips each side of the pivot head, bridge the
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationPick-up Truck. Four Ferry-Boat Vehicles 135 FULL-SIZE PATTERNS
2MA.PAG_2MA.PAG /20/ :9 PM Page Pick-up Truck The main body can be made in two sections; the location of the joint is indicated in the drawing. Glue these sections together before adding the Pick-up s
More informationTools: Sharpie, Square, Vise, Hack saw, Ruler, Punch, Hammer, File. 2. Cut the stock Place stock in vise and cut with hack saw
Purpose: MAKE CATAPULT ARM Step 1 Tools: Sharpie, Square, Vise, Hack saw, Ruler, Punch, Hammer, File Materials: Flat aluminum ½ inch stock (see picture below) Gloves required 1. Pick up the aluminum ½
More information