MLCS Instructions for Bowl and Tray Template Kit #9176/#9179
|
|
- August Chambers
- 6 years ago
- Views:
Transcription
1 MLCS Instructions for Bowl and Tray Template Kit #9176/#9179 Tools Needed: Router 1-1/2 h.p. Minimum recommended with a 1/2 collet Forstner bit 3/4-2 recommended depending on template used Drill Press to use with the Forstner bit to reduce overall time and stress on the router Compass to lay out the exterior of the bowl/tray Bandsaw or Jigsaw to cut the exterior shape of the bowl/tray 3/8 (or preferred) radius Round Over Router Bit to ease the bowl/tray edges Getting Started: Glue up a minimum 18 x 18 (for a round bowl/tray) or an 18 x 24 (for an elliptical bowl/tray) blank out of stock, the thickness of your total bowl/tray height. You may use a stack of laminations to achieve the final thickness (2-3/4 is the maximum recommended thickness with this router bit collet extension combination) if thicker stock is not available or if you want a fancier look. In that case you may also consider using different species of woods to vary the color of the bowl/tray. Do not use biscuit joinery for this as Copyright MLCS Woodworking. Page 1
2 the biscuit slots may show when the material is removed around the interior and exterior of the blank. A simple edge-to-edge glue joint of boards that have been properly jointed is sufficient for this project. Just make sure to thoroughly cover all the mating surfaces with a sufficient amount of glue and avoid applying too much clamping pressure that could squeeze out enough glue to cause the bond to fail prematurely. Clamp this assembly up and allow the glue to completely dry before attempting to machine it. Using the template of your choice, layout the pattern on your stock and trace around the inside of the template (see figures A & B). If you are using a multi-section template reposition the template to complete each section of the bowl/tray until you have the full layout of your bowl/tray drawn on the top of your stock. Temporarily remove the template from the stock. figure A figure B Install the forstner bit in your drill press and remove the bulk of the interior area of your bowl/tray by making overlapping holes with the forstner bit. You do not need to cut right up to the layout lines, you will remove any remaining stock using the dish cutting router bit. Set the drill stop depth to allow the forstner bit to cut to a depth approximately 3/8 1/2 from the final intended depth of your bowl recess (see figures C & D). Fig. C Fig. D figure C figure D Copyright MLCS Woodworking. Page 2
3 Because of the large open areas in the template, you will need to add a large base to your router. This can be made from acrylic, MDF, hardwood or plywood. The base needs to be made out of a thickness of material that will remain stiff and not allow excessive flex with the router attached. This will keep the bottom of the recess flat and smooth and require less sanding at the end of the project. The size needed for this should be large enough so the router plate can span the template and be in contact with at least two opposing sides of the template, so that the router plate does not fall into the recess which would allow the bit to cut too deep ruining the bowl/tray. You will need to make a through hole in this for the router bit to fit through. You can use a forstner bit that is at least 1-3/8 in diameter to make the hole to allow the 1-1/4 diameter bit to fit through the plate (see figure E). You will need to drill and countersink mounting holes in this to attach the router to this new large router base. figure E Before you can rout to remove the remaining material from the interior sections of your bowl/tray, you need to secure the template to your blank. You can either use double sided tape or the templates have two countersunk screw holes in them to allow you to securely fasten them using screws. Align the template with your original layout lines and secure them using one of the above methods (see figure F). figure F Copyright MLCS Woodworking. Page 3
4 Depending on how much travel your router has, you may find the collet extension will cause the bit to protrude too far out of the router base for the first few passes. The cuts should be made using multiple passes, lowering the bit height between each pass and a safe depth for the first cuts should be about 1/4 increments. The top mounted ball bearing will follow the template and then the recess as you get deeper down into your bowl/tray. Only use the collet extension if and when you reach the travel limitations of your router, and need the extra reach the collet extension provides. Start routing and continue routing until you have reached the final depth of your recess, which should leave about 1/2 of material on the bottom of your bowl/tray. If you are using a multi-section template, reposition the template at the other recess locations and repeat the routing operations at all recess locations until you have completed all of the routing of the bowl/tray. You will now need to remove the outside area from around your bowl/tray. Use a standard compass to trace an outline of your bowl/tray. Set the compass for the thickness you would like the outer wall of your bowl/tray to be. Use the compass by running it along the inside edge of your recess and trace around the outside edges of each of the recesses to produce a uniform line around the exterior of your bowl/tray (see figure G). figure G Use a bandsaw (or jigsaw if you do not have a bandsaw) to carefully cut just to the outside of the line to make the exterior wall of your bowl/tray. The more accurate and careful you are with this step, the less sanding you will have to do to create a smooth even exterior to your bowl/tray. Use a sanding drum or palm sander, if available to smooth out the exterior of your bowl/tray. This will be much faster than hand sanding (see figure H). To finish the inside of the bowl/tray, a bowl sanding disc on a hand drill or drill press will allow you to finish sand the interior of your bowl/tray (see figure I). Copyright MLCS Woodworking. Page 4
5 figure H figure I You can choose to use a round over or chamfer profile around the inside and outside perimeter of your bowl/tray if you wish to relieve the sharp corners (see figure J). figure J Finish your bowl/tray with a food safe finish such as mineral oil, salad bowl oil or shellac. Copyright MLCS Woodworking. Page 5
Cactus Routed Bowl. MLCS Items Needed:
Cactus Routed Bowl MLCS Items Needed: Cactus Bowl and Tray Template #9188 Top Mounted Bearing Dish Cutter Router Bit #7817 1/2 Router Collet Extension and Wrenches #9465 45* Degree Chamfer Bit #7676 1-3/8
More informationChili Pepper Routed Bowl
Chili Pepper Routed Bowl MLCS Items Needed: Chili Pepper Bowl and Tray Template #9189 Top Mounted Bearing Dish Cutter Router Bit #7817 1/2 Router Collet Extension and Wrenches #9465 3/16 Radius Round Over
More informationCOFFEE TABLE WITH RECESSED TRAY
COFFEE TABLE WITH RECESSED TRAY Why not treat your guests to a tray laid with delicacies and then remove it from sight in your new coffee table. There's no easier way to show that you are a thoughtful
More informationSeamed Undermount Bowls
CUTOUT TEMPLATES MAKING CUTOUT TEMPLATES 7.1 CUTOUT TEMPLATES The use of an accurate template is one of the most essential elements to the successful completion of a cutout in Corian. For the completion
More informationCoffee table with recessed tray
Coffee table with recessed tray Dinner is served Coffee table with recessed tray This coffee table has it all: it contains a recessed tray, so that you can treat your guests to various delicacies. 1 Introduction
More informationProject 19496EZ: Rocking Horse. Rocking Horse Materials List
Project 19496EZ: Rocking Horse A delightful must gift for preschoolers, our rocking horse is made from sturdy stock like maple or birch. Easy to build with optional detailing: if you don t want to paint
More informationA Unique Cutting Board
A Unique Cutting Board When I was asked to make a cutting board as a special gift, I wanted to do something new and eye-catching. Tired of squares and straight lines, I envisioned curving accents not shallow
More informationSilverware Chest Plan
Silverware Chest Plan 05L14.01 Introduction 1. Measure the space required for your cutlery before beginning this project to be sure that it will fit in the drawers and top compartment. The best way to
More informationWays to get the most out of your
5 Ways to get the most out of your router table When you mount a router on a table, you expand your shop s potential. To help you take advantage of this potential, we assembled five router table techniques
More informationTraditional Undermount: S Method (Undermount):
TOOLS REQUIRED 15.1 TOOLS REQUIRED The installation of Corian shape product must be a precise and exacting process to ensure that a good fit is always created. Using the correct tools is essential. In
More informationDisplay Case (for J&S)
Display Case (for J&S) This is constructed of maple plywood with solid maple (soft maple) edge banding. It was made to fit between a door and a kitchen cabinet, and has an elegant circular taper between
More informationInstructables Butcher Block Top
Instructables Butcher Block Top Project Overview: This project requires basic woodworking skills and access to woodworking machines. Woodworking machines have sharp cutting edges and are NOT forgiving.
More informationThe WoodWorker s Edge
The WoodWorker s Edge Draw-leaf Game Table 1. 2. Layout the area for the tenons. The tenons are 3/8 thick x 4-1/2 long x 1-1/4 deep and offset to the inside. Create the tenons using the step method to
More informationARTS AND CRAFTS CHAIR
ARTS AND CRAFTS CHAIR 491 MATERIALS LIST--DINING CHAIR Key No. Size and description (use) A 2 1-3/4 x 1-3/4 x 16-1/4'' oak (front leg) B 2 1-3/4 x 3-3/4 x 40-1/2'' oak (rear leg) C 1 1-3/4 x 3-3/16 x 15''
More informationKitchen Step Stool. Premium Plan. In this plan you ll find: America s leading woodworking authority
America s leading woodworking authority Premium Plan In this plan you ll find: Step-by-step construction instruction. A complete bill of materials. Construction drawings and related photos. Tips to help
More informationCopyright MLCS 1
Copyright 2007. MLCS 1 WORKING WITH BOX JOINTS Box joints (AKA "Finger Joints") provide a simple, yet equally effective, alternative to dovetail joinery. In particular, they serve well for applications
More informationMATERIALS: TOOLS: CUT LIST:
MATERIALS: (3) 4x4x8 Ft. Boards (8) 2x4x8 Ft. Boards 2 ½-inch Pocket Screws 2 ½-inch Wood Screws 1-inch Wood Screws (16) Figure 8 Tabletop Fasteners Wood Glue Wood Filler TOOLS: Tape Measure Pencil Carpenter
More informationCopyright 2007 MLCS 1
Copyright 2007 MLCS 1 REFERENCE GUIDE and SPECIFICATIONS: Edge Guides: This 12 Dovetail Template comes complete with 2 Edge Guide Sets one set for Half Blind and one set for Rabbeted Half Blind Dovetails.
More informationCOMPLIMENTARY WOODWORKING PLAN
COMPLIMENTARY WOODWORKING PLAN COFFEE TABLE PLAN This downloadable plan is copyrighted. Please do not share or redistribute this plan in any way. It has been paid for on your behalf by JET Tools, a division
More informationServing Tray. When some good friends got married recently, An exercise in template-making yields a great gift project that s easy to duplicate
Serving Tray An exercise in template-making yields a great gift project that s easy to duplicate END Create from 3 8 2 8" piece. By Geoff Noden When some good friends got married recently, I decided to
More informationThis is a solid wood cabinet. The only plywood used is for the back and drawer bottoms.
Sideboard Sideboard Overview: This project requires basic woodworking skills and access to woodworking machines. Woodworking machines have sharp cutting edges and are NOT forgiving. You should be properly
More informationPROJECT PLAN TRAVEL CRIBBAGE BOARD
BUILD IT WITH ROCKLER PROJECT PLAN TRAVEL CRIBBAGE BOARD BUILD Stock # Item Stock # Item 59160 Small Cribbage Board Template, 2-Player, Straight Track 90638 3/4" Dia. Straight Router Bit (1/2" shank) 21026
More informationProject Skill Level: INTERMEDIATE Plywood Used: CANPLY EXTERIOR Good Two Sides (G2S) or precision sanded Aspen
Project Skill Level: INTERMEDIATE Plywood Used: CANPLY EXTERIOR Good Two Sides (G2S) or precision sanded Aspen MATERIALS LIST: (1) ¾" x 4 ft x 8 ft plywood panel (20) #8 x 2" Robertson or Phillips wood
More informationROUTER BITS. Rabbeting Bits. Rabbeting Bits with Bearing Set Comes with interchangeable bearings to cut rabbets of different depths.
32-098 ROUTER BITS 42 32-504 Rabbeting Bits Produces super smooth cuts on both surfaces of the rabbet. Can be used for joining boards and for letting in back panels. Steel pilots can be removed from bits
More informationSMART ROUTING KIT. Sliding Arm. Perpendicular Stops* Control the movement along the Y-axis. Traveler Two slots for positioning on the Guide Rail
SMART ROUTING KIT The EZ SMART Smart Routing Kit (SRK) is the original routing kit for the EZ SMART system. It turns the average router into a production tool capable of multiple axis routing with CNC-like
More informationTurning a Fast Joint dovetailed vase on a lathe
Turning a Fast Joint dovetailed vase on a lathe Contributed by customer Brian H from Knoxville TN The MLCS Fast Joint precision joinery system offers a broad range of dovetail patterns that can be created
More informationPaper Towel Holder Project
Paper Towel Holder Project Name: Date: Description: Construction of the towel holder utilizes scrap lumber to make a useful project. Workmanship is a key part of the project. In Building this project you
More informationBUILDING A STORM DOOR
BUILDING A STORM DOOR BY NEAL BARRETT Illustrations by George Retseck If you're in the market for a storm door, you probably know that there are many styles and models available. However, most of them
More informationSINKS AND LAVATORIES. Steps to completion: These items are essential for installing all sinks:
DUPONT CORIAN SOLID SURFACE FABRICATION/INSTALLATION FUNDAMENTALS NA/ENGLISH SINKS AND LAVATORIES INTRODUCTION This bulletin discusses installing DuPont Corian solid surface sinks and lavatories. OVERVIEW
More informationStand & Bowls. optional. Online Extra
Online Extra optional Stand & Bowls Once you make a bowl using the jig and technique from Woodsmith No. 229, it s only natural to see what else you can do with it. The starting point is to make copies
More informationwoodworkersjournal.com MATERIAL LIST
MATERIAL LIST T x W x L 1 Legs (2) 1 1 2" x 3 1 2" x 36 7 16" 2 End Uprights (2) 1 1 2" x 3 1 2" x 32 1 2" 3 Stringers (4) 1 1 2" x 3 1 2" x 42" 4 Top Cladding, Long (2) 3/4" x 7 1 4" x 65 3 4" 5 Side
More informationADULT. Adirondack / Muskoka Chair Plans
ADULT Adirondack / Muskoka Chair Plans Materials List 3/4" x 9 1/2" (1.9cm x 24.1cm) redwood, cedar or pine boards. Six, 8' (2.44m) boards should make one chair depending on knots and layout. You can also
More informationRouter Table. Construction
Router Table A router table is an invaluable tool. The problem, however, is that ready-built router tables are usually relatively expensive and too narrow for many projects. This router table provides
More informationArched. Building an. Passageway. Although my company specializes in high-end jobs
Building an Arched Passageway All photos by Brian Striegler This straightforward approach combines basic shop methods with simple site joinery to create an elegant frame-and-panel archway by Gary Striegler
More informationApartment Dining Table
Jeff Branch WOODWORKING You Can Build an Apartment Dining Table By JEFF BRANCH H ave you ever found yourself wanting a new piece of furniture, but everything you see in stores is too big? Big furniture
More informationGreene & Greene. Mailbox. by Seth Keller. Signature details create an elegant box. 2 AmericanWoodworker.com
Greene & Greene Mailbox by Seth Keller Signature details create an elegant box. 2 AmericanWoodworker.com We needed a new mailbox, but I couldn t find an off-the-shelf version that I liked. So I decided
More informationTall Outdoor Chair Set March/April 2018
Tall Outdoor Chair Set March/April 2018 Traditional, low-slung Adirondack chairs are an enduring favorite among woodworkers, because their casual styling makes them easy to build. But, once you re seated
More information30 FINE woodworking. Photo, this page: Michael Pekovich
30 FINE woodworking Photo, this page: Michael Pekovich Arts & Crafts Bed White-oak bed is loaded with Stickley style and topped off with traditional inlay by Kevin Rodel This bed design is a close copy
More informationAmerica s leading woodworking authority To download these plans, you will need Adobe Reader installed on your computer. If you want to get a free copy, visit: http://adobe.com/ reader. Having trouble downloading
More informationTen Essential. These bits will conquer the majority of woodworking tasks. b y G a r y R o g o w s k i. Operating: handheld vs.
Ten Essential Router Bits These bits will conquer the majority of woodworking tasks b y G a r y R o g o w s k i You ve bought a new router, unpacked it, and even found the switch on it. But that s only
More informationContents. pages 20-24: Installing Edge sinks into. custom laminate countertops page 8: Installing Edge sinks into postform laminate countertops
Contents pages 2-8: Installing Edge sinks into custom laminate countertops page 8: Installing Edge sinks into postform laminate countertops pages 9-14: Installing Acrylic sinks into custom laminate countertops
More informationMortisting Stand. Premium Plan. In this plan you ll find: America s leading woodworking authority
America s leading woodworking authority Premium Plan In this plan you ll find: Mortisting Stand Step-by-step construction instruction. A complete bill of materials. Construction drawings and related photos.
More informationA candle stick addresses transferring and reproducing dimensions from a plan and breaking the project into steps.
Activities Discussion These projects allow more skill development including making items to match a drawing, sizing projects to specific dimensions, and just trying fun stuff for the first time! A candle
More informationFloating-Top Table. Creative joinery adds spark to this versatile piece
Floating-Top Table Creative joinery adds spark to this versatile piece By Michael Pekovich 28 FINE woodworking This is one of those projects that almost wasn t. Rachel, my wife, had asked for a small,
More informationCopyright 1998 KDE Technologies
Modular Computer Corner Desk Unit Copyright 1998 KDE Technologies http://members.tripod.com/~kdetech/ 1. Introduction 2. Plans Sheet one - Isometric Sheet two - Top Detail / Corner Unit Sheet three - Leg
More informationProject 12231EZ: Country Curio Clock
Project 12231EZ: Country Curio Clock This good-looking clock not only reminds you of the time, it also provides a couple of shelves to display favorite curios. No fancy joinery is needed here, just butt
More informationAsk your DIY store or carpenter to cut the required boards to size. Instructions. 1. Cut out the opening for the bottles
KITCHEN TROLLEY Next time you're whipping up some magic in the kitchen, take advantage of our willing assistant. Fixed on rollers to provide easy mobility, our kitchen trolley can be stationed wherever
More informationProject Plans Kreg Tool Company/BuildSomething. All Rights Reserved.
BY Project Plans ONE-OF-A-KIND CUTTING BOARD This solid-maple cutting board offers ample space for cutting and a comfortable handle, but the most-unique feature lies underneath. A cutout in the lower layer
More informationDIY CHILD S STOOL. Instructions
DIY CHILD S STOOL Children have their own special world. And having the right furniture is part of that world. We have designed an easy-to-assemble child's stool that you can paint in a selection of bright
More informationHinge Mortising Jig. One of the make it or break it parts of building a. 6 ShopNotes No. 74
Hinge Mortising Jig A Mortise for a Hinge. Quick, clean, and accurate that s the only way to describe the mortise you get with a trim router and this hinge mortising jig. One of the make it or break it
More informationWoodline USA Woodline Spacer Fence System
Woodline USA Woodline Spacer Fence System MADE IN THE USA Includes: (1) ¼ Spacer Fence (1) 3/8 Spacer Fence (1) ½ Spacer Fence (1) Hardware Package (1) 3 Piece Brass bar set (2) Setup Blocks Visit Us Online
More informationMail Truck Bank Plan. Rockler Mail Truck Bank Plan
Mail Truck Bank Plan Build this nostalgic Mail Truck Bank and capture the imagination of a child! This easy-to-build plan uses our Solid Brass Mailbox Door (#55358) to commemorate the stalwart little truck
More informationJigsaw Puzzle Tray. Premium Plan. In this plan you ll find: America s leading woodworking authority
America s leading woodworking authority Premium Plan In this plan you ll find: Step-by-step construction instruction. A complete bill of materials. Construction drawings and related photos. Tips to help
More information15 Dovetail Jig. Instruction Manual. Part # 3452
15 Dovetail Jig Instruction Manual Part # 3452 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools. Peachtree Woodworking
More informationCurved Pieces are a Common Woodworking Challenge
Curved Pieces are a Common Woodworking Challenge I recently created a set of four dining chairs that required three curved back rest pieces each. On the top piece of each chair I wanted to inlay a marquetry
More informationRouter Table. In a recent article, I wrote about the router table I built for the Center. 5 Essential Jigs for the
5 Essential Jigs for the Router Table Great fixtures and fences offer better control and new possibilities BY PETER SCHLEBECKER In a recent article, I wrote about the router table I built for the Center
More information(1) C & C 30 MK I I. Building the Wine Glass Holder
(1) C & C 30 MK I I Building the Wine Glass Holder 1. This package contains instructions and sketches plus scanned pictures. 2. Woodworking skills and equipment are essential to make the pieces and assemble
More informationEssential BOX JOINT JIG
Essential BOX JOINT JIG Home in on precise finger joints with this table saw sled. By Ken Burton The box (or finger) joint is a remarkably strong, interlocking corner joint that can be quickly made on
More informationWOODWORKING GUIDE: BASIC JOINERY
WOODWORKING GUIDE: BASIC JOINERY Close isn't really good enough. A perfect fit is what counts. When building furniture, there are many ways to construct joints. The simplest are those that use mechanical
More informationBuild a Rolling Tool Tote
The rolling tool tote design calls for readily available materials: a cheap hand truck (it could be an axle and two wheels), 3/4 and 1/2 thick plywood, 1/4 thick MDF (you could use plywood or hardboard)
More informationA Shaker Sewing Stand
America s leading woodworking authority Step by Step construction instruction. A Shaker Sewing Stand A complete bill of materials. Exploded view and elevation drawings. How-to photos with instructive captions.
More informationDenise M. DeRose Handled Clamshell Handbag
Denise M. DeRose Handled Clamshell Handbag Materials: Wood 2 discs between 6 and 9 in diameter -- 4/4, 6/4 or 8/4 1 piece of thin hardwood ¼ inch thick and 4 x 10 Wood for waste blocks Supplies Small piece
More informationProject 11010EZ: Gun/Bookcase/Curio Cabinet
Project 11010EZ: Gun/Bookcase/Curio Cabinet No man can be all things to all people, but this cabinet comes as close to fitting multiple uses as any inanimate object can. We ve pictured it as a gun cabinet
More informationgravity feeder GRAVITY FEEDER
Z5979i_pg066-077.indd 68 3//10 4:09:48 PM gravity feeder USING A TRIED-AND-TRUE DESIGN, GRAVITY feeders can hold a large amount of chow. The wide opening at the bottom accommodates a seed mix containing
More informationShaker Classic Change the legs to change the look
Shaker Classic Change the legs to change the look 2 Ways B Y C H R I S T I A N BECKSVOORT not long ago, a couple ordered a set of cherry side tables from me, one for each side of their pencil-post bed.
More informationA Slim,Comfortable. In 1979 I spent five months designing. This system works for most chairs and uses common materials
A Slim,Comfortable This system works for most chairs and uses common materials An upholstered slip seat complements a beautiful chair. Using modern materials, it s not difficult to construct an elegant
More informationCowper From Steve Wolverton on the T&TTT forum, Feb 2005 For Reference Only Do not use to build a trailer. Check on Teardrop and Tiny Travel Trailers
Cowper From Steve Wolverton on the T&TTT forum, Feb 2005 For Reference Only Do not use to build a trailer. Check on Teardrop and Tiny Travel Trailers for up to date building information; http://www.mikenchell.com/forums
More informationThree Legged Stool. Randy Cordle / 2016
Three Legged Stool Randy Cordle / 2016 This stool could easily qualify as fine furniture, being equally at home in the living room or featured at the local arts and crafts fair. A few unique construction
More informationDewalt Organizer Storage Cabinet Plans
Dewalt Organizer Storage Cabinet Plans Version 1.0 How to build a system to perfectly organize you Dewalt storage organizers. With easy to follow step-by-step instructions, you will be able to cut, assemble,
More informationProject 17884EZ: Shaker End Table
Project 17884EZ: Shaker End Table With its clean, simple lines, this piece is unmistakably Shaker style. Ours is made from cherry, a wood commonly used by Shaker craftsman, but we ve also seen this piece
More informationPlans. Easy-to-Build Full-size Deluxe Murphy Bed Plan. For more plans, tools and hardware visit rockler.com
Easy-to-Build Full-size Deluxe Murphy Bed Plan Build a full-size Deluxe Murphy Bed complete with decorative molding and matching side cabinets! Plans For more plans, tools and hardware visit rockler.com
More informationHow to Construct the 8-Point Star by Jay S. Helland
How to Construct the 8-Point Star by Jay S. Helland 1-5-2013 The photos in these instructions were not taken in consequential order but provide the reader the general idea of the processed used. The process
More informationBUILDING A SELMER MACCAFERRI GUITAR
BUILDING A SELMER MACCAFERRI GUITAR A step-by-step guide to building a laminated body Selmer-Maccaferri guitar Michael Collins The Heel The heel should now be prepared to be glued to the neck shaft. Using
More informationGambling queen. This tournament-sized backgammon. I PROJECT Backgammon table
I PROJECT Backgammon table BY DUNCAN ROSE Gambling queen This commission was placed by a customer who knew exactly what he wanted in appearance, dimensions, functionality and style; a backgammon table
More informationA Pictorial of David Dawes AA400 HFT Thumbhole Stock in the Making
DRAFT Version A Pictorial of David Dawes AA400 HFT Thumbhole Stock in the Making Part 1 and finally Part 2 as well Updated: February 2008 By James Mitchell (a.k.a. mitchejc) Note: Building rifle stocks
More informationDurable Outdoor Table
54 F I N E W O O D W O R K I N G Durable Outdoor Table Ipé table will seat six and weather many seasons B Y D A V I D B E D R O S I A N Last summer brought a new pool to our backyard. With it came more
More informationTools: Drill/Driver Kreg Jig Miter Saw Jigsaw Circular Saw Adjustable Square Tape Measure Veneer Trimmer Sandpaper and Sander
R PROJECT PLANS DROP-FRONT DESK Create a workspace almost anywhere with this drop-front desk. Mounted to a wall, it doesn t take up any floor space, which means you can hang it wherever you need to work.
More informationINSTALLATION GUIDE VERSION 11/14
INSTALLATION GUIDE VERSION 11/14 In this guide we will demonstrate effective techniques and methods for installing EDGE stainless steel sinks seamlessly in both laminate and solid surface. These techniques
More informationKlamp Trak. Instructions (39052)
Klamp Trak TM Instructions (39052) ITEM# KKS1020 - Klamp Trak TM Getting Started There are three main methods for installing Klamp Trak in your workshop. In all three methods, your goal will be to construct
More informationWESTERN PISTOL.22 CALIBER SINGLE SHOT. Entire pamphlet Copyrighted by JACO Designs 1972
WESTERN PISTOL.22 CALIBER SINGLE SHOT Entire pamphlet Copyrighted by JACO Designs 1972 This pamphlet contains the plans and instructions necessary to construct the Western pistol. This pistol breaks open
More informationMake your own zero clearance throat plate.
Make your own zero clearance throat plate. A picture tutorial By Wayne Breshears One of the more important table saw accessories you can have is a zero clearance insert or throat plate. The close tolerance
More informationcraftsman rocker Classic style meets comfort in this sturdy oak rocking chair BY MICHAEL PEKOVICH 34 FiNE woodworking
craftsman rocker Classic style meets comfort in this sturdy oak rocking chair BY MICHAEL PEKOVICH 34 FiNE woodworking photo, this page: Michael pekovich shape the rear legs designing a chair can be a tough
More informationHandle Hardware Kit for Router Plane 05P38.10
Handle Hardware Kit for Router Plane 05P38.10 Introduction With this kit, you can make a set of replacement handles for the Veritas Router Plane. The following instructions describe how to make one handle
More informationRequired Tools. Installation of Hook Plates & Discs. Professional Installation Guidelines for Engineered Wood & Hardwood with LocPlate Products
Professional Installation Guidelines for Engineered Wood & Hardwood with LocPlate Products Required Tools Utility Knife Chalk Line Measuring Tape Conventional cutting tools for Engineered Wood and Solid
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 2
Kentucky 4H Wood Science Plans Notebook Plans Level 2 MATERIALS NEEDED: JEWELRY BOX WS201 1 piece wood 1/4" x 4 x 4 1/2" (bottom) 1 piece wood 1/4" x 4 1/2" x 5 (top) 2 pieces wood 1/4" x 2 x 5 (front
More informationClassic Project. Cat Push Toy. In this plan you ll find: $1.00 WJC023. Step-by-step construction instruction. A complete bill of materials.
America s leading woodworking authority Classic Project In this plan you ll find: Step-by-step construction instruction. Cat Push Toy A complete bill of materials. Construction drawings and related photos.
More informationAhead of the curve 2 Part
F&C PROJECT Ahead of the curve 2 Part In the second part of this series, Chris Tribe constructs the table for his stylised cabinet which we looked at last month in F&C Accuracy in turning the legs for
More informationB-BENDER Do It Yourself Installation Instructions
(Parsons/Green) B-BENDER Do It Yourself The Hipshot (Parsons/Green) B-Bender is designed and manufactured to provide decades of trouble free service when it is properly adjusted and installed. These installation
More informationindicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
f a r m h o u s e d i ni ng c h a i r What You'll Need lumber Beginner 1-1 x2x4 1-1 x2x8 3-2x3x8 1-2x4x8 1-3/4 x 2 x 4 sheet of plywood (availability will vary) Intermediate Intermediate Beginner About
More informationBuild a comfortable outdoor seat in time for spring
asy lider Build a comfortable outdoor seat in time for spring by Vern rassel Our glider features metal swing arms that are easy to install and provide a smooth gliding motion. W hen you re choosing a spot
More informationJeff Branch WOODWORKING YOU CAN BUILD A. By adding subtle design elements, a traditional furniture style becomes decidedly modern.
Jeff Branch WOODWORKING YOU CAN BUILD A By adding subtle design elements, a traditional furniture style becomes decidedly modern. Jeff Branch WOODWORKING Publisher: Jeff Branch Editor: Jeff Branch Art
More informationPackage contains. Required tools and consumables:
Thank you for purchasing the TriTrix MTM Transmission Line cabinet kit. This cabinet kit was precision cut using CNC machinery for the best possible fit and finish. With a little time and patience, your
More informationI I. . i1 AD JUSTABLE SHELVES
ADJUSTABLE SHELVES HAD BEEN TRYNG TO WORK out a really simple (read "fast") way to make an elegant wooden version of the old standby, metal standards and brackets. Although have seen many commercial versions
More informationRobert Bosch GmbH. Minimalist washstand
Minimalist washstand Neat and tidy Minimalist washstand Minimalist design in the bathroom is in fashion. And rightly so, as this washstand proves: because less is more! 1 Introduction Here s an idea to
More informationFLAT TO FABULOUS Make a Bowl from a Single Flat Board - Or How to Eat Salad off of Scrap Wood
FLAT TO FABULOUS Make a Bowl from a Single Flat Board - Or How to Eat Salad off of Scrap Wood Let s face it: Woodworkers are frugal people. In fact, if you are anything like me, you have a hard time throwing
More informationA Pictorial of David Dawes AA400 HFT Thumbhole Stock in the Making
A Pictorial of David Dawes AA400 HFT Thumbhole Stock in the Making From This This To Part 1 By James Mitchell (a.k.a. mitchejc) Note: Building rifle stocks is super fun and the idea with this pictorial
More informationULTIMATE ROUTER TABLE PLANS. By Dan Phalen
ULTIMATE ROUTER TABLE PLANS By Dan Phalen January 2017 Ultimate Router Table Plans. Copyright 2012-2017 by Daniel Phalen. Published by Creston Hall Publishing Company. All rights reserved. No part of this
More informationTraditional glass-pane and wood-muntin doors highlight this free-standing piece.
Bookcase Traditional glass-pane and wood-muntin doors highlight this free-standing piece. As the saying goes, there's nothing like good books. But they can present some storage problems--especially if
More informationRouter Table-Mate. Everything you'd want in a router table for just $50.
Router Table-Mate Everything you'd want in a router table for just $50. Commercially made router tables are everywhere these days. Some of them come with more gizmos and gadgets than a 59 Edsel. By the
More informationExtendable Large Dovetail Jig
Extendable Large Dovetail Jig Instruction Manual Part # 3458 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools.
More information