Pachinko Machine. Supplies: Part One: Construction. Optional: (1) 21" x 15.5" piece of wood. jumbo craft sticks. (2) 17" x 1" pieces of wood
|
|
- Stephany Lindsay Perry
- 6 years ago
- Views:
Transcription
1 Supplies: (1) 21" x 15.5" piece of wood jumbo craft sticks (2) 17" x 1" pieces of wood standard craft sticks (2) 14.5" x 1" pieces of wood 1" wooden craft circles (2) 4" x 2" pieces of wood drill (1) 14.5 x 2" piece of wood 1/2", 15/64",1/8" drill bits (1) 15.5" x 2" piece of wood hot glue or wood glue 14" embroidery hoop craft knife 1/8" dowel ruler 3/16" dowel pencil 1" escutcheon pins, #18 hammer 50mm split plastic tree ornament hand saw 3/4" L x 1/4" W aluminum spacers sandpaper 1/2" ball bearings or marbles Optional: paint template transfer paper 1
2 1.. Measure and cut 2" from both ends of a jumbo craft stick. Measure 1.25" of the remaining craft stick and cut it to have one 1.25" piece and one 0.75" piece. 2. Measure and mark 5/8" away from the left edge on both the top and bottom edges of the 1.25" piece. Connect each mark to the center of the left edge to form a point. 3. Cut out the shape that you just made. It should be a rectangular shape with a pointed end. 4. Apply glue to the bottom of one of the first pieces that you cut out in step one. 5. Glue the two end pieces together to form a V shape that has a 2" opening. The rounded edges should be at the opening. 6. Glue the pointed piece on top of the V shape to make a basket. 7. Add a small pile of hot glue to the bottom of the inside of the basket. 8. Place the 0.75" piece at an angle on top of the glue to make a small ramp. This will guide the ball into the hole if it lands in a basket. 9. Now make three more baskets! 2
3 10. Glue one end of the aluminum spacer to the center of a craft circle. This will be a spinner on your board. 11. Measure from the spacer to the end of the circle. Ours is about 0.25". 12. Measure and cut the ends off of two popsicle sticks so that they are the same length as the distance measured in step Glue the four ends to the spacer so that they are perpendicular to each other. 14. Make three more spinners! 15. Measure and cut a 1" piece from your 3/16" dowel. 16. Sand the ends so that they are smooth and flat. 17. Glue two jumbo craft sticks together so that they are about 0.5" off center. 18. Glue the 1" piece of dowel to the end of one of the craft sticks from step 17. 3
4 19. If you are using our template, cut a piece of transfer paper to match its size. 20. Find where you want the center of your pachinko game to be and drill a 15/64" hole. 21. Lay the transfer paper down with the template on top so that the center hole is above the hole that you drilled. 22. Now trace all of the other drill holes. They are the green circles on the template. 23. Drill the holes that you traced. Make sure to sand each hole so that the balls can freely roll in and out of the holes. 24. Measure 5/8" from the edge of one of the side bumper pieces of wood. Drill a hole there using the 1/2" bit. 25. Glue the bumpers of your game onto the board. Make sure the hole that you drilled in one of the bumpers is on the bottom right when your game is standing straight up. 26. Remove the clasp from the embroidery hoop with the hand saw. 27. Glue a small cube of scrap wood on top of the center of your bottom bumper. 5
5 28. Bend the embroidery hoop so that it touches the top, left, and right bumpers. Mark where there is excess hoop on the right side of your board. 29. Cut off the excess hoop and glue your embroidery hoop down. Glue the bottom edge to the scrap cube. 30. Measure and cut the other hoop so that it connects to the end of the first hoop on the right side of the board and curves to the top. Glue it down. 31. Cut the 1/8" dowel into four 1" pieces. 32. Put the pieces of dowel into the aluminum spacers on the wheels and mark how far they go in. 33. Add a small amount of glue to the four wheel holes and hammer each dowel piece in until they reach the marks that you made in step Trace the remaing portion of your template onto the board. 35. Glue the ball baskets over each ball hole. Be careful not to obscure the holes with glue! Lightly sand the plastic ornament and glue it to the center of your board. You might have to make the ornament shorter using the hand saw. 36. Place one spinner on top of each of the four dowels. 6
6 37. Hammer the nails according to the template, or make your own design! Just make sure that the ball cannot get stuck anywhere. 38. Hammer the nails closely together to create the walls that guide the balls into the baskets. These are represented by solid curved lines on the template. 39. Tune in next week to find out how to make a ramp, ball tray, stand, and launcher! We will also be adding lights, sounds, and an Arduino to our pachinko game. 7
Build the Spitfire: Step-By-step. Pack 7 Stages 61-71
Pack 7 Stages 61-71 1 Stage Contents Page Number 61 212-215 62 216-218 63 219-221 64 222-224 65 225-228 66 229-231 67 232-235 68 236-238 69 239-241 70 242-245 71 246-249 Editorial and design by Continuo
More informationA Total Overhaul and Playing Field Replacement on a Nishijin Model B
A Total Overhaul and Playing Field Replacement on a Nishijin Model B Supplies: Simple Green to clean all the parts. White vinegar, Painter s tape, Double sided sticky tape, Turtle Wax Chrome Polish on
More informationBig Oz. Rocket. User Guide V0313
Big Oz Rocket User Guide 59824 V0313 Materials Included The Big Oz Rocket Kit should include the following materials. If something is missing, contact Customer Service at 800-358-4983. 20-ounce plastic
More informationDIY RUSTIC HALL TREE
DIY RUSTIC HALL TREE *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever using power tools
More informationA Total Overhaul and Playing Field Replacement on a Nishijin Model B
A Total Overhaul and Playing Field Replacement on a Nishijin Model B Supplies: Simple Green to clean all the parts. White vinegar, Painter s tape, double sided sticky tape, Turtle Wax Chrome Polish on
More informationPROJECT PLANS WOODEN GIFT BOX
PROJECT PLANS WOODEN GIFT BOX Make the gifts you give even more special by presenting them in this one-of-a-kind gift box. In fact, the box may be valued more than whatever it contains. The box is sized
More informationTEMPLATE (FORM) PROCEDURE:
Paper Sculpture MATERIALS NEEDED: Sketchbook Paper/Pencil/Eraser Scissors/ Ruler Template Patterns Glue stick/ Hot Glue Gun Colored Markers REQUIREMENTS: 1. Minimum 5 shapes (Use uneven number) 2. Must
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 1
Kentucky 4H Wood Science Plans Notebook Plans Level 1 MATERIALS NEEDED: 1 piece wood 3/4" x 2 x 2 1 piece wood 3/4" x 3 x 3 1/2" 1 wooden spring-type clothespin 2-1 1/2" nails 1-1/2 woodscrew Wood Glue
More informationSheet Metal Toolbox. Tools:
Sheet Metal Toolbox Name: Date: Description: 15 long sheet metal toolbox with wood ends and a dowel for handle. Useful for tools or supplies. Combines both beginning sheet metal skills and wood working..
More information15 Dovetail Jig. Instruction Manual. Part # 3452
15 Dovetail Jig Instruction Manual Part # 3452 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools. Peachtree Woodworking
More informationWOOD TOY NEWS. July 23, 2013 Tuesday
WOOD TOY NEWS Make your own perfect turntable for spray painting toys with these useful tips. And it s fast, fun and easy to build! by Imants Udris Watch the video on our website at : http://www.toymakingplans.com/website/how-to/
More informationHubble Space Telescope Paper Model Directions Downloads, patterns, and other information at:
Hubble Space Telescope Paper Model Directions Downloads, patterns, and other information at: www.hubblesite.org/go/model Materials: model pattern printed onto cardstock/coverstock instructions printed
More informationCockpit Kit. Full Depth - Builds Quickly - Light Weight READ THROUGH THIS INSTRUCTION MANUAL FIRST. IT CONTAINS IM- laser cut wood kit
The Savage Light Sukhoi Su- 27 Cockpit Kit contains everything you need to build a full depth semi scale Su-27 cockpit, yet adds less than an ounce to your finished model s weight (not including pilot).
More informationCoat Rack. Materials: Directions:
Coat Rack 2x2 wooden poplar (foundation of the rack) 3/4 inch diameter wood dowels (5-8 depending on how many arms you want) 1/4 inch dowel screw 1/4 inch drill bit Power drill Ruler Pencil Paint/spray
More informationPaper Pinwheel. Supplies
Paper Pinwheel 1. Draw some lines. Measure and cut a square piece of paper.» Use the ruler and pen to draw lines from each corner of the paper towards the center. These lines should be half the size of
More informationNATURE camp Engines. By: Daniel Tuhy
NATURE camp 2015 Engines By: Daniel Tuhy Description: In this lesson students will gain a general knowledge of what an engine is and the different types of engines. Students will participate in 3 activities
More informationgravity feeder GRAVITY FEEDER
Z5979i_pg066-077.indd 68 3//10 4:09:48 PM gravity feeder USING A TRIED-AND-TRUE DESIGN, GRAVITY feeders can hold a large amount of chow. The wide opening at the bottom accommodates a seed mix containing
More informationWEBELOS CRAFTSMAN SUGGESTED DEN ACTIVITIES
SUGGESTED DEN ACTIVITIES Visit furniture factory, lumber mill or lumberyard. Some local home centers offer special weekend classes for Webelos age children. Invite someone to give a demonstration on the
More informationBuilding Tips This model can be built using the following types of adhesives:
Page 1 Building Tips This model can be built using the following types of adhesives: Epoxy (with or without microballons) Odorless cyanoacrylate (CA) with accelerator UHU Creativ for Styrofoam (or UHU
More informationSan Felipe: Step by Step Pack 3
Pack 3 Your parts Bulwarks Gun port covers x 2 Tools and equipment Wood glue Sandpaper Brushes Wood stain Hammer Pin pusher/nails Razor saw a Remove the longer bulwark and test-fit it in place at the bow
More informationEND FRAMES. End frames built using pressure treated 2x4 (1 1/2" x 3 1/2") 36" 34" 7/16" pilot hole. 5 1/2" x 1/2" lag bolt 8" wheel 23"
END FRAMES End frames built using pressure treated 2x4 (1 1/2" x 3 1/2") 23" 17 1/2" (B) (B) Measure from the bottom of your stone to 1" below the lip to get your measurement. 17 1/2"(B) 36" 34" 1/2" flat
More informationExtendable Large Dovetail Jig
Extendable Large Dovetail Jig Instruction Manual Part # 3458 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools.
More informationCedar 2-Drawer Desktop Storage Cube
Cedar 2-Drawer Desktop Storage Cube 5 ½ Dimensions 5 ½ 5 ½ 2 2 1 7/8 4 ¼ 4 ½ Author s Notes: Build a Cedar 2-Drawer Desktop Storage Cube from just 1 cedar fence picket. No angles, special cuts or rips
More informationSLIM TRIM MOULDING INSTALLATION METHODS
Slim Trim as a reducer Use SlimTrack (Metal Track) for up to 4 mm floors. Up to 4 mm Floors 3/8 *If the flooring manufacturer suggests/permits the use of underlayments you may need to shim the track to
More informationSHAPES & COLORS. Copyright by The Adventures of Scuba Jack, Inc., All rights reserved.
SHAPES & COLORS CIRCLE DIAMOND RECTANGLE SQUARE STAR TRIANGLE COLORING SHAPES CIRCLE SQUARE Color the circle red. RECTANGLE Color the square green. TRIANGLE Color the rectangle blue. DIAMOND Color the
More informationDress Form Pincushion (In-the-Hoop)
Dress Form Pincushion (In-the-Hoop) Craft a tribute to your favorite hobby with this classic dress form design. Stitch each piece in-the-hoop in your choice of fabric, then assemble and stuff to create
More informationSky-in-a-Box Instructions
Strand 1 Activity 7 The Shifting Stars Sky-in-a-Box Instructions Large or Small? The Sky-in-a-Box designs are provided ready to print on A4 or US Letter size paper. Used at this size they will require
More informationDIY X Panel Side Table
DIY X Panel Side Table *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever using power tools
More informationSmall Town Buildings. Scaled and easy to read patterns and instructions. Shoe / Western Union (with and without porch)
1 /24 th Scale Patterns kiva design G R O U P E 1 Story Flat Roof Yard and Garden Buildings Compatible with Garden Railroads or a delight for any child's collection Overall Dimensions Foundation: 10" x
More informationCO 2 DRAGSTER DESIGN AND CONSTRUCTION Notes for Students
CO 2 DRAGSTER DESIGN AND CONSTRUCTION Notes for Students EXAMPLES OF DRAGSTER SHAPES AND STYLES 1. Shell Cars the wheels hidden inside the body 2. Rail Cars the wheels outside the body 3. Shell Reveal
More informationSASKATOON, Saskatchewan
CONSTRUCTION GUIDE AVRO ARROW (CONTEST VERSION) Copyright, Bill Jones, 2004 SASKATOON, Saskatchewan This is a work in progress, so there are a couple of rough areas ( I ll point out those that I m aware
More informationU. M. ARMY Texas Conference. Wheel Chair Ramp Manual
U. M. ARMY Texas Conference Wheel Chair Ramp Manual June 2014 U. M. ARMY Texas Conference Building & Repair Tips Wheelchair Ramps Complete a site survey to determine the design and layout of the ramp.
More informationContinue gluing the remaining top parts ensuring the angled piece is glued well. Set aside and let dry. See photo below
Radiator rev 1.1 The SE5a s radiator is one of the most recognized radiators in WW1. It is one of the components that defines the SE5a. The original SE5a has seen multiple radiator designs used during
More informationwoodworkersjournal.com MATERIAL LIST
MATERIAL LIST T x W x L 1 Legs (2) 1 1 2" x 3 1 2" x 36 7 16" 2 End Uprights (2) 1 1 2" x 3 1 2" x 32 1 2" 3 Stringers (4) 1 1 2" x 3 1 2" x 42" 4 Top Cladding, Long (2) 3/4" x 7 1 4" x 65 3 4" 5 Side
More informationSmall 45 Roof Houses 1 or 2 Story 1 /24 th Scale Patterns
BA GARDEN TOWNS 45 Roof Houses 10" x 10" 1 or Story Scaled and easy to read patterns and instructions for wood houses. Yard and Garden Buildings Compatible with Garden Railroads or a delight for any child's
More informationMaking a Cement Upper Molding Surface for Compression Molding of Shape&Roll Prosthetic Foot Cores
Making a Cement Upper Molding Surface for Compression Molding of Shape&Roll Prosthetic Foot Cores Andrew Hansen, PhD Steven Steer, MS Kerice Tucker Elizabeth Klodd Craig Heckathorne, MS Northwestern University
More informationHow to Assemble the Vacuum Formed Plastic 7/8 Scale Lewis Gun
How to Assemble the Vacuum Formed Plastic 7/8 Scale Lewis Gun 1. Read ALL the instructions before starting assembly. 2. Begin assembly by thoroughly washing the inside and outside surfaces of the vacuum
More informationProject: Trebuchet Overview: This medieval launcher would reek. Materials: 3/4 plywood, 2 of 5/8 threaded. Minimum Cutting Area: 2 sheets of plywood
Project: Trebuchet Overview: This medieval launcher would reek havoc on enemies castles. However, the modern day conversion using 20lbs of weight will easily through a tennis ball the length of a gymnasium.
More informationCollage Pendant from Recycled Tin
PROJECT BEGINNER METAL Construct a Collage Pendant from Recycled Tin Cut, stack, and rivet elements from colorful tin containers to create a reversible pendant with a wooden core. by Christine Terrell
More informationTECHNICAL FILE FOR THE STIRLING ENGINE
TECHNICAL FILE FOR THE STIRLING ENGINE FABRICATION RANGE ELEMENT: Support ring SET: Stirling engine RANGE: 1 SHEET: 1 of 1 DRAWING: N 11 MATERIAL: white NUMBER: 1 PVC N o PHASE, SUB-PHASE OR 10 MAKING
More information4. Bevel the LE face of HS1-HS11 to match the horizontal stab leading edge sweep angle.
BEFORE YOU BUILD 1. Unroll each sheet of the plans. Roll them inside out so that they will lie flat on the building surface. 2. Assemble the tools that you will need to build each section so that they
More informationValentine Boy. Pattern and Instructions. By Cutest Voodoo
Valentine Boy Pattern and Instructions By Cutest Voodoo Before we start... This pa ern is copyrighted by Cutest Voodoo. This is an original design and is made for personal use only. Mass produc on of this
More informationPROJECT PLANS EXPANDABLE CRAFT CENTER
R PROJECT PLANS EXPANDABLE CRAFT CENTER Whether you re working on craft projects, sewing, or pursuing another hobby, this craft center offers a great place to work. It features a large work surface that
More informationSAN FELIPE: Step by Step Pack 2
Pack 2 Your parts Stern reinforcement Bulkheads The poop deck Bulkhead planks Planks Tools and equipment Knife Pencil Wood glue Sandpaper File a Using leftover 5 x 5-mm wooden strips, measure and cut beams
More informationSeamed Undermount Bowls
CUTOUT TEMPLATES MAKING CUTOUT TEMPLATES 7.1 CUTOUT TEMPLATES The use of an accurate template is one of the most essential elements to the successful completion of a cutout in Corian. For the completion
More informationHollow metal clay forms are typically built over organic cores like. Coreless Construction: Rethinking the Metal Clay
PROJECT INTERMEDIATE METAL CLAY Coreless Construction: Rethinking the Metal Clay Build this four-sided pendant using forethought and a 3-D template. by Cindy Ambrose FCT-MWON0216_ART17 Hollow metal clay
More informationCar Construction E-Book
Physics Lecture 14 - Building the Simple But Fast (SBF) Car-Part 1 Introduction The following lecture uses information from the Car Construction E-Book on the Virtual Race CD. This Lecture does not, however,
More informationMOVING TO THRIVE: ACTIVITIES FOR AGES 10 TO 18 YEARS
WHO AM I One pack of post it notes, a timer, and a pen to write. Write down any famous characters or celebrities on a post it note. Stick the post it note on one person s forehead, making sure that everyone
More information#P570 - Leavenworth Requires a pendulum movement kit (#A309 - #A312) 24 H x 14 W
- Leavenworth Requires a pendulum movement kit (#A309 - #A32) 24 H x 4 W Cut on dashed line for Back Cut on solid line for Frame only. Stock: /8 - /4, cut each Left pattern piece. GENERAL SCROLLSAW TIPS
More informationBUILD THE. Soleil Royal. Pack 1. The flagship of King Louis XIV.
BUILD THE Soleil Royal The flagship of King Louis XIV www.model-space.com Pack 1 Stage 1 Assembly Guide Hull frame, false keel and first deck half A 4 2 5 1 6 7 1A Smooth the surfaces of all the pieces
More informationBeautiful Bouquet. Designed by Heidi Pridemore. Page All Rights Reserved The Whimsical Workshop
O - 3/5/12 Designed by Heidi Pridemore #FR-032 Fabric Requirements: 1/3 yard of Green- for all 1/3 yard of Yellow- Daisy 1/3 yard of Orange- Daisy 1/4 yard of Pink- Poppy 1/4 yard of Yellow Print- Poppy
More informationBUILDING A GOAL WALL DO IT YOURSELF! INSTRUCTIONS FOR A GOAL WALL
INSTRUCTIONS FOR A In just a few steps, we show you how to build your own goal wall and paint it perfectly. COMPILED BY 1 PREPARING Purchase the materials from the enclosed list. The DIY store should be
More informationZiroli D-17 Beech Staggerwing
Ziroli D-17 Beech Staggerwing Parts List Vacuform Parts: Miscellanous Pieces 1 Four Side Panels 1 3/16" Tube, 2" Long 2 Lower Dash - Back Dash 2 Felt, 12x24 3 Dash 3 Cordury 12x24 4 Dash Hood 4 Aluminum
More informationHow to Mitre Mouldings
How to Mitre Mouldings About Window and Door Mouldings Mitre cuts are a basic operation in most moulding installation. Mitre cuts are typically 45 degree angles, however many installations require minor
More informationWays to get the most out of your
5 Ways to get the most out of your router table When you mount a router on a table, you expand your shop s potential. To help you take advantage of this potential, we assembled five router table techniques
More informationHinge Mortising Jig. One of the make it or break it parts of building a. 6 ShopNotes No. 74
Hinge Mortising Jig A Mortise for a Hinge. Quick, clean, and accurate that s the only way to describe the mortise you get with a trim router and this hinge mortising jig. One of the make it or break it
More informationMerry Mailbox. Store all of your holiday cards in this Merry Mailbox!
Merry Mailbox Store all of your holiday cards in this Merry Mailbox! A great addition to any Christmas decor, this mailbox is a fun and festive way to display all your holiday greetings. Read below for
More informationPITTS S2S CONSTRUCTION
PITTS S2S CONSTRUCTION FUSELAGE CONSTRUCTION 1) Place the right fuselage side over the plan and mark the former positions. Place the left side over the right side and mark the former positions. Glue F1
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 2
Kentucky 4H Wood Science Plans Notebook Plans Level 2 MATERIALS NEEDED: JEWELRY BOX WS201 1 piece wood 1/4" x 4 x 4 1/2" (bottom) 1 piece wood 1/4" x 4 1/2" x 5 (top) 2 pieces wood 1/4" x 2 x 5 (front
More informationBleeding Control Prop for Tourniquet Practice Advanced Bleeding Control
Do It Yourself Bleeding Control Prop for Tourniquet Practice Advanced Bleeding Control Introduction Hands-on skill practice is necessary to developing competence in using commercial or improvised tourniquets.
More informationWRIGHT FLYER 1 INSTRUCTIONS FOR THE D10LC KIT
WRIGHT FLYER 1 INSTRUCTIONS FOR THE D10LC KIT Manufactured in the USA by Easy Built Models PO Box 681744, Prattville, AL 36068-1744 Visit us at www.easybuiltmodels.com Easy Built Models GLUE METHODS Always
More informationTools and Tips: ( 1 )
Tools and Tips: As you build instructions will show in my many picture manual how to assemble. You can use your own methods as you desire, my results are very good. A smooth, flat work surface is very
More information3Position the hull of the ship as
Yamato: Step-by-step 25 The hull and stern deck c b d a b d c e e f a Rear frame b Stern deck x 2 c Stern deck x 2 d Side wall x 2 Wood glue Sandpaper (no. 400 grain) Craft knife Pliers d Side wall x 2
More informationThe finished ornaments.
Introduction I like to make different Christmas Ornaments every year to give to my relatives. This article describes the rnaments that I m making this year. The ornaments use a split turning of either
More informationMousetrap Catapult. About this project:
Designed by: Ritchie Kinmont Project #44 Page 1/19 About this project: The is fun for ages four and up. Using a mousetrap for the spring, this catapult is designed to throw objects such as practice golf
More informationWanderlust Suitcase Vanity
Wanderlust Suitcase Vanity If you re like me, you re always up for an adventure. When I saw some examples of DIY reclaimed suitcases, paired with the exciting new Wanderlust embroidery design collection,
More informationBasic Directions for Preparing. And Aligning Split Designs for. Multi-Hoop Sew-outs
Basic Directions for Preparing And Aligning Split Designs for Multi-Hoop Sew-outs Prepared and copyrighted by Barbara Carlson February 5, 2003 Using Victoria design from Machine Cross Stitch Victorian
More informationFryer's Trebuchet Paper Kits
Fryer's Trebuchet Paper Kits Things you will need 7 sheets of card approx. 0.3 mm or 0.01 inches thick 1 sheet of paper to print out to download. 2 x 6-7 mm dowel or pencils 1 paper clip String 6 cms (2.5
More informationDesktop Trebuchet Kit Assembly Instructions
Desktop Trebuchet Kit Assembly Instructions Contents of package (drawings are not to scale for clarity, parts that have duplicates are indicated with total number of that part to be found, example: 2X
More informationFLEXITEEK INSTALLATION INSTRUCTIONS
an Advanced Plastic Fabrications Company 99 marcus Blvd., 631.244.3620 631.231.4466fax FLEXITEEK INSTALLATION INSTRUCTIONS Before you begin, take your new Flexiteek deck out of the shipping package and
More informationTriangles. Pendulum. Dangling from handmade curvilinear ear wires, Construct earrings from carefully fitted panels. METAL CLAY EARRINGS
The front of each earring is impressed with a slightly different pattern than those used on the sides and backs. 1¾ in. (44mm). beginner/intermediate metal clay METAL CLAY EARRINGS Pendulum Triangles Construct
More informationTOOLS 2 ½ hole saw (a good sharp one. You re going to make 36 holes.) Sharp pencil Yard stick Compass Protractor Sandpaper Rasp Drill Motor Jig Saw
My version of this upright rifle rack does not have a turntable or lazy Suzan on it. I need to be able to move my rifles around so I opted to put casters on the bottom of the rack. With four casters, it
More informationAerospace Speciality Products
Specifications:! Length: 18.75"/47.6 cm! Diameter: 0.98"/24.9 mm! Weight: 1.5 oz/44 gm! Streamer Recovery! Recommended Engines:!! A8-3; B4-4; B6-4; C6-5! Skill Level: Beginner This is a model rocket kit
More informationUsing the star template provided, trace out half the star shape on the pegboard sheet. Flip template over and trace out other side of star.
Shining Star PROJECT INFORMATION Created by DIY hacker, woodworker and teacher, Kerryn Carter of Toolschool, brighten up your Christmas with this shining Star, complete with LED lights for extra twinkle.
More informationFORWARD FUSELAGE SIDES & REAR TOP SKINS
FORWARD FUSELAGE SIDES & REAR TOP SKINS WORK REPORT Step No. Check Parts / Tools Qty Preparations. 1 [ ] 6F5-3 Upper Front Longerons 2 2 [ ] 6F5-5 Heel Support 1 3 [ ] 6F5-2 Front Floor Skin 1 3 [ ] Firewall
More informationAssembly Instructions to make the box organiser for the board game Perditions Mouth
Assembly Instructions to make the box organiser for the board game Perditions Mouth With a craft knife and sandpaper, remove the pieces from the sheets of plywood as you do each tray. The pieces are almost
More informationRosalina Accessories Tutorial Version March 2011 Martyn
Rosalina Accessories Tutorial Version 1.0 - March 2011 Martyn Star Brooch Feel free to experiment with these dimensions, you should make a template you are happy with, the method still works. 1) Creating
More informationFancy Keepsake Box. Premium Plan. In this plan you ll find: America s leading woodworking authority
America s leading woodworking authority Premium Plan In this plan you ll find: Step-by-step construction instruction. A complete bill of materials. Construction drawings and related photos. Tips to help
More informationGnome Bottle Topper. Project Needs & Notes:
Gnome Bottle Topper Make holiday celebrations a little merrier when you invite this jolly little fellow! Just stitch and turn the hat, then add a faux fur beard and finishing details to turn any wine bottle
More informationSan Felipe: Step by Step Pack 6
Pack 6 Your parts Framing Tools and equipment Glue Knife Sandpaper Superglue Tweezers Clear varnish a Retrieve the grating that you assembled on Page 100. Cut two pieces of 2 x 3 mm wooden strip to fit
More information3Insert the second rod no. 4
Yamato: Step-by-step 37 The stern block and searchlight control towers a b c d e f Recommended tools and materials Wood glue Sandpaper (no. 800 grain) Metal file Putty Craft knife For metal: Super Glue
More information#P571 - Victorian Queen Fretwork Clock inspired by 18th century Victorian elegance. 17 H x 21 W. Requires a 3 1/2 clock insert.
- Victorian Queen Fretwork Clock inspired by 8th century Victorian elegance. 7 H x 2 W. Requires a 3 /2 clock insert. Cut on dashed line for Back Cut on solid line for Frame only. Stock: /8 - /4, cut each
More informationPROJECT PLANS ROLLING LAUNDRY SORTER
R PROJECT PLANS ROLLING LAUNDRY SORTER Sorting laundry certainly doesn t rank high on anyone s list. So, anything that makes this task easier is welcome. If that functionality can be mixed with a bit of
More informationThe odometer TEACHER S GUIDE
The odometer TEACHER S GUIDE April 2009-1- PREPARATION Activity 1 Objective: Context Peg-Leg Max s letter (2 versions) Mathematical lexicon Duration: 10 minutes Read or have the students read the messages
More informationEXPLORING SCIENTIFIC PROCEDURES. Freebies!!!!
EXPLORING SCIENTIFIC PROCEDURES Freebies!!!! Box of spaghetti, Two feet of string, Small paper cup, Paperclip, 50-60 pennies (other items will work such as paperclips, marbles, etc.) Place the piece of
More informationDeck the Door Holiday Decor
Deck the Door Holiday Decor Deck your home for the holidays, and greet visitors at the door with colorful, seasonal messages. This door or wall hanging combined embroidery with Christmas foliage for a
More informationpolymer clay. by Jill Erickson
intermediate polymer clay You ought to be in pictures... Transfer your favorite photographs to jewelry using polymer clay. by Jill Erickson This direct image-transfer technique is easy to master and does
More informationHAND TOOL NOTES For each tool picture and name, please write what it s used for. You will have a quiz on this.
HAND TOOL NOTES For each tool picture and name, please write what it s used for. You will have a quiz on this. Tool (Name & Nut drivers Speed Square Adjustable Bevel Square CONSTRUCTION TOOLS: Tool (Name
More informationBuilding the Gothic Church
Building the Gothic Church Mold #54 does not contain all of the blocks to build this church. You will need extra regular blocks (1/2" x 1/2" x 1") and square blocks (1/2" x 1/2" x 1/2"). These blocks can
More information1 ¼-inch Pocket Screws Brad Nailer or Hammer 1 ¼-inch Brad Nails Clamps
MATERIALS: TOOLS: (4) 2 x 6 x 8 Ft. Boards Tape Measure (2) 2 x 4 x 8 Ft. Boards Carpenter s Square (7) 1 x 4 x 8 Ft. Boards Pencil (2) 1 x 3 x 8 Ft. Boards Drill (1) Half Sheet of ¾-inch Thick Plywood
More informationKraftyKid s Winter Holiday Projects
KraftyKid s Winter Holiday Projects Holiday Napkin Rings Happy Hanukkah Happy Hanukkah Happy Hanukkah Happy Hanukkah Easy Gingerbread Cookie Ornament Recipe (Makes 6 ornaments not for eating!) 1/2c Applesauce
More informationRIM: Use a purchased rim, or cut and drill a donut rim from plywood or MDF.
Home-made DIY e-drums These e-drums are pretty simple to make from MDF and/or plywood, inexpensive wooden embroidery hoops, purchased rims, and fiberglass window screen. They are very low profile, less
More informationTECHNIQUE. Because of the flexibility of the woven paper elements, this necklace moves nicely when worn. BEGINNER PAPER/WOOD. facetjewelry.
TECHNIQUE FCT-SR-09248-03 BEGINNER PAPER/WOOD Because of the flexibility of the woven paper elements, this necklace moves nicely when worn. 203 Kalmbach Publishing Co. This material may not be reproduced
More informationAssembly Instructions for Busted Bricks Marble Machine #1
Assembly Instructions for Busted Bricks Marble Machine #1 Ver. 2 instructions Page number 1 Required for assembly: Wood glue (PVA or aliphatic resin recommended) and/or Cyanoacrylate (CA) glue Clamps or
More information#P536 Mary Wall Plaque Create our beautiful and intricate fretwork wall plaque in honor of the Mother of our Savior. Over 17 tall.
Mary Wall Plaque Create our beautiful and intricate fretwork wall plaque in honor of the Mother of our Savior. Over 7 tall. Cut on dashed line for Back Cut on solid line for Frame only. Stock: /8 - /4,
More information#P2-21 Victorian Wall Pocket Organize and decorate all at the same time with this handy wall pocket. 12 tall.
Victorian Wall Pocket Organize and decorate all at the same time with this handy wall pocket. 12 tall. Cut on dashed line for Back Cut on solid line for Frame only. Stock: 1/8-1/4, cut 1 each Left pattern
More informationTable of Contents. Pom-Pom Bookmark Yarn covered Pencil Holder Yarn Hangers... Yarn Hair Bows
1 Table of Contents Pom-Pom Bookmark... 3-5 Yarn covered Pencil Holder... 6-8 Yarn Hangers... 9-11 Yarn Hair Bows... 12-14 Tassel Necklace or Gift Wrapping... 15-17 No Knit Infinity Scarf... 18-20 Braided
More informationBuild the Spitfire: Step-By-step. Pack 3 Stages 21-30
Pack Stages 2-0 Contents Stage Page Number 2 72-74 22 75-78 2 79-8 24 82-84 25 85-88 26 89-9 27 92-94 28 95-97 29 98-00 0 0-05 Editorial and design by Continuo Creative, 9-4 North Road, London N7 9DP All
More informationDesigned by Melissa DiRenzo thesweetescape.ca
instructions Designed by Melissa DiRenzo thesweetescape.ca YOU WILL NEED 3 -diameter foam ball Christmas sweater Hot glue gun and glue sticks 3/8 -wide satin ribbon Elastic thread: metallic Note: A child
More information1Use the metal file to smooth
Yamato: Step-by-step 85 Parts of the bridge and the hull a b c d e f a Part of the bridge b Part of the bridge c Part of the bridge d Radar x 2 e Part of the bridge x 2 f Wire Recommended tools and materials
More information