Build the Spitfire: Step-By-step. Pack 3 Stages 21-30
|
|
|
- Alexandra Wells
- 5 years ago
- Views:
Transcription
1 Pack Stages 2-0
2 Contents Stage Page Number Editorial and design by Continuo Creative, 9-4 North Road, London N7 9DP All rights reserved 204 De Agostini Publishing USA, 95 Broadway, Suite 609, NEW YORK, NY 000 BUILD THE SPITFIRE complies with CE regulations. Items may vary from those shown. NOT SUITABLE FOR CHILDREN UNDER THE AGE OF 4. THIS PRODUCT IS NOT A TOY AND IS NOT DESIGNED OR INTENDED FOR USE IN PLAY. ITEMS MAY VARY FROM THOSE SHOWN.
3 Stage This stage s parts - Wing rib 2 - Wing rib 4 - Wing rib Wooden strip 4 x 4 x 00mm You will need Pencil Sandpaper Glue Triangle or T-square 2 2 Remove any burrs or splinters from the ribs and then mark their numbers (, 4 and 5) on them. Apply glue to the corresponding notch of the spar after test-fitting rib. 72
4 4 Place the rib into the notch. Make sure the projections at the bottom of the rib are flush with the work surface. Also check that the upper part of the rib is flush with the upper side of the spar º 2 Hold a triangle up against the rib and the spar to ensure that it dries at a right angle. Test-fit rib 4 in the notch two along from rib. Then apply glue. 7
5 7 8 Place rib 4 into the notch, checking that the projections and the top are flush, and that it is positioned at a right angle. 9 Test-fit rib 5 in the spar, two notches along from rib 4, then apply glue to the notch. 0 Place the rib into the notch and check the position, as with the previous ribs. Ensure that the distances between the ribs are equal at the front and back. Here is how the wing should look. Set aside any parts supplied but not used. 74
6 Stage This stage s parts - Wing rib Wing rib - Rib 5 reinforcements 4 - Wooden strip 4 x 4 x 00mm You will need Pencil Knife Sandpaper Glue Triangle or T-square 2 2 Sand the two ribs to remove any burrs or splinters. Mark their numbers (6 and ) on them to identify them later. 75 Test-fit rib 6 in the notch two down the spar from rib 5. Adjust the fit if necessary and then glue into place on the spar.
7 4 90º Check that the top and bottom of the rib are properly positioned, then hold a triangle up against the rib and the spar to ensure that it dries at a right angle. Now remove the two reinforcements shown in the picture from the reinforcement sheet. 5 6 Sand the reinforcements to remove any burrs or splinters. Apply glue to the front of the ninth rib of the right wing. Place the two reinforcements into position, slotting them into the spar and aligning them with the outer edge of the rib. 76
8 7 Now remove the shorter of the remaining reinforcements. Apply glue at the back of the ninth rib, along the dotted line, on the same side as the reinforcements at the front. 8 Fit the reinforcement at the back of the rib, aligning it with the top edge of the rib. 77
9 9 0 Remove the last reinforcement and sand it smooth. Apply glue to the underside of the rib, on the same side as the other reinforcements. Place the reinforcement onto the side of the ninth rib. Try to align the edges of both as best you can. This is how the wings should appear after this stage. Don t forget to set aside any parts that haven t been used. 78
10 Stage 2 2 This stage s parts - Wing rib Rib 6 reinforcements - Rib 5 reinforcements You will need Knife Sandpaper Glue Wooden block Pencil 2 2 Remove the two parts from the reinforcement sheet, as shown. Sand them lightly to remove burrs and splinters. 79 Apply glue to the lower half of the front of the rib shown (dotted line).
11 4 Place the reinforcement flush with the edge of the rib, as shown. Test-fit the reinforcement up against the rib, make any necessary adjustments, and then apply glue along the dotted line. 5 6 Place the reinforcement up against the side of the rib. Make sure it is flush with the top edge. Place the left wing on a block of wood, in the same way as you did with the right at Stage 2. 80
12 7 8 Apply glue to the notch between the first two ribs of the left wing. 9 Fit rib 2 into the glued notch, resting the back end on the block of wood. 0 Before the glue dries check that the spacing between the first three ribs is equal. Make sure that the top of the rib is aligned with the spar. This is how the wings should appear after this stage. Don t forget to set aside any parts that haven t been used and mark the identifying number on any ribs. 8
13 Stage 24 2 This stage s parts - Wing rib 2 - Wing rib 4 - Rib reinforcements You will need Wooden block Pencil Sandpaper Glue Knife 2 Position a block of wood underneath the back of the left wing. Test-fit rib in the highlighted notch in the main spar of the left wing. Then apply glue to the notch. 82
14 4 2 Place rib into the notch, making sure that it is evenly spaced between the two adjacent ribs and that it is flush with the top of the spar. Now take rib 4 and test-fit it in the next available notch in the main spar. Apply glue to the notch Place the rib into the notch, evenly spaced between the two adjacent ribs, and flush with the top of the spar. Remove the two rib reinforcements from the sheet and smooth with sandpaper. 8
15 7 8 Position the right wing with the underside facing up. Apply glue to the outside of the second rib. 9 Place the reinforcement onto the side of the rib, aligning the outer edges of both. 0 Test-fit the reinforcement along the bottom of the rib, make any necessary adjustments, and then apply glue. Now fit the reinforcement in place. Make sure, as with all other reinforcements, that it is flush with the edge of the rib. The wings should now look like this. Keep any unused material to the side. 84
16 Stage 25 2 This stage s parts - Wing rib Rib reinforcements - Wooden strip 4 x 4 x 00mm You will need Glue Ruler Pencil Saw 2 Raise the back half of the left wing. 85 Test-fit rib 5 in the wing, adjust the fit if necessary and then apply glue to the notch in the main spar, as shown.
17 Place the rib into the notch in the spar. Check that the back of the rib is spaced evenly between the two adjacent ribs. 4 Place the fuselage on its right side. Mark a line 20mm from the upper edge of the left lateral fuselage, as shown in the picture. 20mm 86
18 5 Mark another line 20mm from the edge, located further toward the rear of the fuselage, as shown. 20mm 6 Take a x 5 x 00mm wooden strip from a previous stage and glue it below the marks made in Steps 4 and 5, up against the join between the two fuselage side pieces (dotted line). 87
19 7 8 Cut off the excess strip once it s dry so that it is flush with the first frame. 9 File the end of the strip to make sure that it is perfectly flush with the frame. 0 20mm 20mm Repeat Steps 4-6 for the right side of the fuselage. Cut off and file the end of the strip so that it is flush with the first frame of the fuselage. The left wing and fuselage should now look like this. Keep any unused materials to the side for later use. 88
20 Stage This stage s parts - Wing rear spar 2 - Wing rib 7 - Wing rib Wooden strip 4 x 4 x 00mm You will need Pencil Glue Triangle or T-square Mark the rib numbers (7 and 6) on the corresponding ribs. Take rib 7 and test-fit it in the highlighted notch on the left wing. Then, apply glue to the notch. 89 Place the rib into the notch, checking that it is aligned at the top and bottom with the other ribs.
21 4 90º Hold a triangle up against the rib and the spar to check that the rib dries at a right angle. Retrieve rib provided with Stage 22. Place the rib into the spar, as shown, but do not glue. 5 6 Apply glue to the notches of the ribs that have projections on the underside of them (arrows). Place the rear spar over the notches on the tops of the ribs, as shown. Before fitting into position, look at the next step. 90
22 7 8 The position of the notch in the rear spar causes the first rib to sit diagonally to the others. 9 Raise the back of the wing up and make sure that the tops of the ribs are all aligned with the rear spar. Apply glue to rib to secure it to the spars. 0 Now take the rib provided with Stage 20 and apply glue to the ends of the two wing spars. Place rib onto the ends of the spars. Note that the ends of the spars are angled, so the rib won t sit perfectly vertically. Your wing should now look like this. Don t forget to set aside unused materials and mark any ribs with their numbers. 9
23 Stage This stage s parts - Wing rib Rib 6 reinforcements - Wing rib Wooden strip x x 00mm You will need Pencil Triangle or T-square Glue 2 Take rib 6 provided with Stage 26. Test-fit in the highlighted notch, adjust the fit if necessary and then apply glue to the notch. 92 Slide the rib down into the notch in the spar, making sure that it is evenly spaced between the adjacent ribs.
24 4 Test-fit and glue rib 8 into place in the highlighted notch on the main spar. Make sure the projection on the underside of the rib is resting on your work surface and that it is aligned with the top of the spar. 5 6 Before the rib dries in place, ensure that it is positioned at a right angle. Test-fit and glue rib 9 into place in the highlighted notch on the main spar. 9
25 7 8 Make sure the rib is aligned with the other ribs and spar at the top and bottom, and that it dries at a right angle to the spar. 9 Test-fit a 4 x 4mm wooden strip from a previous stage in the groove along the tops of the ribs, behind the spar. Apply glue to the highlighted notches of the ribs. 0 Insert the strip into the groove along the top of the ribs. Look at the next step to see the correct position of the strip. The end of the strip should be positioned halfway across the rib, as shown. Keep any unused pieces to the side and check that your wing looks the same as the one shown here. 94
26 Stage 28 2 This stage s parts - Wing rib Rib 8 reinforcements - Wooden strip x x 00mm You will need Pencil Knife Saw Glue 2 Take a 4 x 4mm wooden strip supplied with a previous stage and place it in the channel in the underside of the ribs, behind the main spar. At the other end of the strip, make a mark at the point shown above. Look at Step 4 to see the correct place. Then cut the strip at this point. 95
27 4 Apply glue to the notches of the ribs where the strip will be positioned (dotted red line). Insert the strip into position in the notches of the ribs, in the same way as Steps and Take the rest of the 4 x 4mm strip and apply glue along the highlighted area of the spar. Place the strip into the notch of the first rib, up against the end of the strip in the second rib. 96
28 7 8 Leave to dry, making sure that the strip remains flush with the strip in the second rib. 9 Cut off the excess strips past the first rib. 0 Test-fit rib 0 at the end of the wing and adjust the fit if necessary. Then apply glue to the end of the spar. Fit the rib onto the end of the spar, making sure that it is parallel with the next rib. Your wing should now look like this. Don t forget to set aside any spare material and identify any leftover parts. 97
29 Stage This stage s parts - Wing rib Wing rib 8 - Wing rib Wing tip You will need Pencil Knife Sandpaper Glue Triangle or T-square 2 Test-fit rib 7 in place on the left wing, in the third remaining notch from the end. Adjust the rib or spar if necessary and then apply glue to the notch. 98 Insert rib 7 into the spar, making sure that it is parallel to the adjacent ribs.
30 4 2 2 Test-fit rib 8 in place. Apply glue to the notch. Insert rib 8 into the notch in the spar, parallel to the adjacent ribs. 5 6 Test-fit rib 9 in place. Apply glue to the notch. Place rib 9 into the final notch of the wing, parallel to the adjacent ribs. 99
31 Check the fit of the wing tip in the last rib on the wing. Apply glue along the dotted line. 9 Glue the wing tip onto the wing, pushing it into the rib, as shown. 0 90º Check that the wing tip is at an angle of 90 to the last rib. Make sure the wing tip dries parallel to your work surface. This is how the left wing should now look. Store and identify any leftover materials. 00
32 Stage This stage s parts - Rear spar 2 - Wing tip ribs (upper) - Rib 9 reinforcements 4 - Wooden strip x x 00mm You will need Pencil Knife Sandpaper Glue Clamp 2 Test-fit the spar into place against the ribs shown, make any adjustments and then apply glue to the contact points. Re-fit the spar, making sure that it is fully engaged with the ribs. 0
33 Take a strip of 4 x 4mm wood provided in a previous stage and place it on top of the wing up against the existing 4 x 4mm strip. Make a mark on the strip, in line with the last rib. 4 Cut the strip to length and apply glue to the cutouts in the ribs behind the main spar. 02
34 5 Glue the strip into position. You may want to hold it there with a clamp while it dries. 6 Take another 4 x 4mm wooden strip and place it along the groove behind the main spar on the underside of the wing, up against the existing 4 x 4mm wooden strip. Make a mark in line with the last rib. Cut the strip to length, apply glue to the contact points and fix into place. 0
35 7 8 E C D G A B 2 F D C B A F E Take the upper wing tip rib sheet that came with this stage. Identify the parts and mark with a pencil, as shown. Remove the pieces from the sheet. Test-fit ribs A-D in the wing tip, adjust if necessary and then glue into place. 9 Test-fit ribs E and F in place in the larger holes at the front of the wing tip. Apply glue to the contact areas and glue into place. F E 04
36 0 Test-fit rib G in the notches of A-F. Apply glue along the line. Then place rib G firmly into position on the wing tip. G The wing should now look like the one shown here. Identify and store any unused parts. 05
Contents. Build the Spitfire: Step-By-step
Pack 2 Stages -20 Contents Stage Page Number 8-0 2 - - 7 8-50 5 5-5 6 5-57 7 58-60 8 6-6 9 6-67 20 68-7 Editorial and design by Continuo Creative, 9- North Road, London N7 9DP All rights reserved 20 De
Build the Spitfire: Step-By-step. Pack 4 Stages 31-40
Pack 4 Stages 31-40 1 Contents Stage Page Number 31 106-108 32 109-111 33 112-115 34 116-118 35 119-122 36 123-125 37 126-128 38 129-132 39 133-136 40 137-139 Editorial and design by Continuo Creative,
Build the Spitfire: Step-By-step. Pack 7 Stages 61-71
Pack 7 Stages 61-71 1 Stage Contents Page Number 61 212-215 62 216-218 63 219-221 64 222-224 65 225-228 66 229-231 67 232-235 68 236-238 69 239-241 70 242-245 71 246-249 Editorial and design by Continuo
BUILD THE. Soleil Royal. Pack 1. The flagship of King Louis XIV.
BUILD THE Soleil Royal The flagship of King Louis XIV www.model-space.com Pack 1 Stage 1 Assembly Guide Hull frame, false keel and first deck half A 4 2 5 1 6 7 1A Smooth the surfaces of all the pieces
USS. Build the CONSTITUTION. The world s oldest commissioned naval vessel afloat
USS CONSTITUTION Build the The world s oldest commissioned naval vessel afloat 04 Build the USS STAGE CONSTITUTION Contents PAGE Wooden strips and a ladder 63 9 Wooden strips and nails 6 30 Wooden strips
SAN FELIPE: Step by Step Pack 2
Pack 2 Your parts Stern reinforcement Bulkheads The poop deck Bulkhead planks Planks Tools and equipment Knife Pencil Wood glue Sandpaper File a Using leftover 5 x 5-mm wooden strips, measure and cut beams
(Build Instructions)
(Build Instructions) Specifications * Wingspan: 58cm * Length: 50cm * Flying Weight: 59 grams * Channels: 3 (Rudder Elevator Throttle) * Suggested Receiver: 4Ch Micro * Motor: 8mm GearDrive * Prop: GWS
USS. Build the CONSTITUTION. The world s oldest commissioned naval vessel afloat
USS CONSTITUTION Build the The world s oldest commissioned naval vessel afloat 05 Build the USS STAGE CONSTITUTION Contents PAGE 39 Bow frames 87 40 Stern frames 89 4 Grating strips, wooden strips and
San Felipe: Step by Step Pack 6
Pack 6 Your parts Framing Tools and equipment Glue Knife Sandpaper Superglue Tweezers Clear varnish a Retrieve the grating that you assembled on Page 100. Cut two pieces of 2 x 3 mm wooden strip to fit
San Felipe: Step by Step Pack 3
Pack 3 Your parts Bulwarks Gun port covers x 2 Tools and equipment Wood glue Sandpaper Brushes Wood stain Hammer Pin pusher/nails Razor saw a Remove the longer bulwark and test-fit it in place at the bow
USS. Build the CONSTITUTION. The world s oldest commissioned naval vessel afloat
USS CONSTITUTION Build the The world s oldest commissioned naval vessel afloat 08 Build the USS STAGE CONSTITUTION Contents PAGE 7 Gun port lids, wooden strips and guns 7 7 Gun port lids, wooden strip
BUILD YOUR OWN. Pack 01
BUILD YOUR OWN TM Pack 01 01 CONTENTS Assembly Guide 03 Stage 1: The fuel tank Stage 2: The cylinder head cover and breather Stage 3: The front wheel and the instruments Stage 4: The handlebars Editorial
BUILD YOUR OWN. Pack 12
BUILD YOUR OWN TM Pack 12 177 CONTENTS Assembly Guide 179 Stage 38: The right crankcase half Stage 39: The IR sensor board Stage 40: The left crankcase half Editorial and design by Continuo Creative, 39-41
SE5a Wing Panels rev 1.0
SE5a Wing Panels rev 1.0 The top and bottom wings are different. They might look the same but the bottom wing has one less rib and some rib spacing difference. This is due to where the wooden interplane
STAGE PAGE. 6 The left front door interior The right front wheel The right front seat back The right front wheel 37
Pack 2 STAGE PAGE 6 The left front door interior 25 7 The right front wheel 29 8 The right front seat back 33 9 The right front wheel 37 10 The right front door 41 11 The right front door window 45 12
The Lansdowne One Car Garage Assembly Instruction by Laser Dollhouse Designs
The Lansdowne One Car Garage Assembly Instruction by Laser Dollhouse Designs NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and
3Position the hull of the ship as
Yamato: Step-by-step 25 The hull and stern deck c b d a b d c e e f a Rear frame b Stern deck x 2 c Stern deck x 2 d Side wall x 2 Wood glue Sandpaper (no. 400 grain) Craft knife Pliers d Side wall x 2
USS Enterprise Instructions
USS Enterprise Instructions If things don t fit right, double check the placement. Because all lasers are different, you may have to sand or file for a perfect fit. Clamp these pieces together and glue
5If the protruding part is. 6Place 1 as is shown in the. 7Place what was assembled
Yamato: Step-by-step 49 The base of the bridge and strakes a c b d a Base of the bridge b Base of the bridge c Base of the bridge d Strakes x 10 THE BASE OF THE BRIDGE 1Smooth 1 to 3, first using the metal
EXTREME LOAD no. TWO
1602 - EXTREME LOAD no. TWO Kit Features: 22' 4 " x 14' x 3'-6 Oversize Load 49mm (1.9") actual height Bolt Head Details Welded Load Mounting Fins Painting Handles Tools Required: Hobby Knife Tweezers
1Take the keel (3) and
1 The hull and the bridge 1Take the keel (3) and apply PVA wood glue in the second slot from the left: a toothpick may make it easier. Take care: the left end is the one that has a projection. THE HULL
Hobby Lobby Zip Supplementary instructions Please refer to the included drawings while using these assembly instructions
Materials needed: 15 or 30 minute epoxy Medium CA Masking tape Scotch tape Servo Tape Wax paper Tools Needed: Pencil or marker Flat building surface Hobby knife or razor blade 7/64" or 3mm drill bit 3/16"
F100 Super Sabre instructions.
F100 Super Sabre instructions. The F100 is a Jet model for the Wemotec 480 Minifan. Start with taking the parts out of the sheet and sand of the connection tabs. Instructions RBCkits F100 Super Sabre 1
PROJECT PLANS WOODEN GIFT BOX
PROJECT PLANS WOODEN GIFT BOX Make the gifts you give even more special by presenting them in this one-of-a-kind gift box. In fact, the box may be valued more than whatever it contains. The box is sized
Articulated Ladder Truck
Special Vehicle Series : 05 Articulated Ladder Truck View of completed model * This model was designed for Papercraft and may differ from the original in some respects. Tools tip Scissors Ruler, set square
BUILD YOUR OWN. Pack 02
BUILD YOUR OWN TM Pack 02 17 CONTENTS Assembly Guide 19 Stage 5: The headlight case Stage 6: The left fork Stage 7: The right fork Editorial and design by Continuo Creative, 39-41 North Road, London N7
Build the. Steam Locomotive. Pack 06
Build the Steam Locomotive Pack 06 Build the Steam Locomotive Contents Step by step Stage 38: The boiler band Stage 39: Sand spreader pipe main cocks Stage 40: Building up the dome Stage 41: The sand spreader
The Olympic DLG. (Discus launch glider) by Chris Brislin
The Olympic DLG (Discus launch glider) by Chris Brislin 1 Contents Parts List/ What you need 3 Before you begin 4 Wing Construction 5-9 Pod Construction 9-13 Tail assembly 13-? Control linkages 9-10 Finishing
RESolution V2 Manual
RESolution V2 Manual Note for the German Manual: Yellow Bottle thick CA Pink Bottle Med CA Blue tube 5 minute Epoxy Green tube 90 Minute Epoxy Construction of the Fuselage Step 1: Cover the plan with a
BUILD AND DRIVE THE RADIO-CONTROLLED MODEL SCALE 1:16
BUILD AND DRIVE THE RADIO-CONTROLLED MODEL 6 SCALE 1:16 CONTENTS STAGE PAGE 28 The second stowage pannier and track 67 29 The right skirt 69 30 The third stowage pannier and track 71 31 The smoke mortars
3Insert the second rod no. 4
Yamato: Step-by-step 37 The stern block and searchlight control towers a b c d e f Recommended tools and materials Wood glue Sandpaper (no. 800 grain) Metal file Putty Craft knife For metal: Super Glue
uin RC FPRC ZERO Specificationss Empty Weight
Flying Pengu uin RC FPRC ZERO Specificationss Wing Span 42.75 (1085 mm) Fuselage length 30.5 ( 775 mm) Empty Weight 9.5 10 oz. (150 160g) Estimated Flying Weight 20 255 oz. (320 400g) Wing Area: 151 sq.
GENERAL NOTES: Page 1 of 9
Laminating A Zia Into A Turning Blank by W. H. Kloepping, Jan. 2009 This describes how a zia (the New Mexico state symbol) can be laminated into a turning blank. Materials needed: Square Turning Block
Build your own. Stages 7-10: See Robi s head move for the first time
Build your own Pack 03 Stages 7-10: See Robi s head move for the first time Build your own All rights reserved 2015 Published in the UK by De Agostini UK Ltd, Battersea Studios 2, 82 Silverthorne Road,
1Use the metal file to smooth
Yamato: Step-by-step 85 Parts of the bridge and the hull a b c d e f a Part of the bridge b Part of the bridge c Part of the bridge d Radar x 2 e Part of the bridge x 2 f Wire Recommended tools and materials
WRIGHT FLYER 1 INSTRUCTIONS FOR THE D10LC KIT
WRIGHT FLYER 1 INSTRUCTIONS FOR THE D10LC KIT Manufactured in the USA by Easy Built Models PO Box 681744, Prattville, AL 36068-1744 Visit us at www.easybuiltmodels.com Easy Built Models GLUE METHODS Always
SZD-10 bis CZAPLA ASSEMBLY MANUAL IN PICTURES
1 RUDDER Plan and parts: 2 Assembly steps: Photo above: glue together rudder spar, ribs and trailing edge. Clamp spar to a flat surface (chipboard on the photo) and make sure the straight aligment of the
Citabria Pro. Aerobatic Parkflyer. by Joel Dirnberger
Citabria Pro Aerobatic Parkflyer by Joel Dirnberger Revision C: December 21, 2004 Citabria Pro Building Instructions Length: Wingspan: Wing Area: Flying Weight: Wing Loading: Functions: Specifications:
1/16" Square balsa strip stock is used for the fuselage and tail surfaces structure. 10T 11T 11B (2) 10B. Pec Bea. Wingspan - 18"
1/16" Square balsa strip stock is used for the fuselage and tail surfaces structure. 10T 9T 8 11T 12 7T 6T F-1 7 11 (2) 10 9 6 13 Pec ea CAD Drawing by Paul radley Sheet 1 of 8 Nose plug is a lamination
Assembly Instructions to make the box organiser for the board game Perditions Mouth
Assembly Instructions to make the box organiser for the board game Perditions Mouth With a craft knife and sandpaper, remove the pieces from the sheets of plywood as you do each tray. The pieces are almost
The Hamlin Assembly Instruction By Laser Dollhouse Designs
The Hamlin Assembly Instruction By Laser Dollhouse Designs NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also gives
Australian Vintage Radio Society Inc.
Australian Vintage Radio Society Inc. (Incorporated in Victoria A0050003S) P.O. Box 3099, Syndal L.P.O., Victoria, 3150, Australia. Cabinet assembly instructions for the AVRS 10 th Anniversary construction
Assembly Manual - Flamenco Guitar Kit
Assembly Manual - Flamenco Guitar Kit Index Contents (pg. 3) Soundboard assembly (pg. 4) Neck to top assembly (pg. 5) Preparation of the sides (pg. 6) Preparation of the back (pg. 7) Body assembly (pg.
Craftman One Car Garage Assembly Instruction by Laser Dollhouse Designs
Craftman One Car Garage Assembly Instruction by Laser Dollhouse Designs NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit.
C-180 Builder s Manual
C-180 Builder s Manual. May 20, 2002 Last revised July 11, 2002 Copyright! 2002 Douglas Binder, Mountain Models www.mountainmodels.com sales@mountainmodels.com (719) 630-3186 1 Required Equipment! Xacto
Hubble Space Telescope Paper Model Directions Downloads, patterns, and other information at:
Hubble Space Telescope Paper Model Directions Downloads, patterns, and other information at: www.hubblesite.org/go/model Materials: model pattern printed onto cardstock/coverstock instructions printed
Building Tips This model can be built using the following types of adhesives:
Page 1 Building Tips This model can be built using the following types of adhesives: Epoxy (with or without microballons) Odorless cyanoacrylate (CA) with accelerator UHU Creativ for Styrofoam (or UHU
Section 75-ZA-2. Rudder Mounting
Section 75-ZA-2 This manual has been prepared for installation of the Rudder. This photo assembly manual is intended as a supplement to the drawings. If there is any discrepancy between this manual and
BUILD AND DRIVE THE RADIO-CONTROLLED MODEL SCALE 1:16
BUILD AND DRIVE THE RADIO-CONTROLLED MODEL 7 SCALE 1:16 CONTENTS STAGE PAGE 34 The fourth stowage pannier 81 35 The gun, mantlet cover and track 83 36 The recoil mechanism 85 37 The infrared receiver 87
BUILD AND DRIVE THE RADIO-CONTROLLED MODEL SCALE 1:16
BUILD AND DRIVE THE RADIO-CONTROLLED MODEL 4 SCALE 1:16 CONTENTS STAGE PAGE 17 The air outlet and track 41 18 The external fuel tanks 43 19 The track and air inlets 45 20 The track and engine access panel
The Universal Table Saw Sled
The Universal Table Saw Sled Do Precision Work Even with Inexpensive Table Saws! Table saw blades always tend to move the wood while the cut is being made. This is why it's so difficult to get accurate
Grade 11 Woods Lift Lid Coffee Table. Based on Under the big Top from Popular Mechanics Website
Grade 11 Woods Lift Lid Coffee Table Based on Under the big Top from Popular Mechanics Website TABLE TOP 1. Select enough lumber to construct a top that is between 22 ½ and 24 wide after jointing. Ensure
Seascape Bungalow Assembly instructions. Laser Dollhouse Designs
Seascape Bungalow Assembly instructions Laser Dollhouse Designs NOTE: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also
Mold #328. Roller Bot. Nail Bot. You will need the following. pieces from mold #328 for this robot. mold #328 for this robot.
Nail Bot mold #328 for this Mold #328 Roller Bot mold #328 for this Stand the piece up and glue the tanks onto the back of the piece. Be sure to center the tanks. Lay these two pieces down on a flat surface
Little Briana Cottage Dollhouse assembly instructions
Little Briana Cottage Dollhouse assembly instructions NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also gives
Allied Tool is a freelance model of a small manufacturing company that grew from production in a home basement to a new building. Assume a gentleman starts assembling gauges in his basement and the business
FUSELAGE CONSTRUCTION
FUSELAGE CONSTRUCTION Note: prior to building and gluing on the work surface use protective covering on your building surface. (wax paper or clear wrap) Fit the laser cut Fuselage Front and Fuselage Rear
Continue gluing the remaining top parts ensuring the angled piece is glued well. Set aside and let dry. See photo below
Radiator rev 1.1 The SE5a s radiator is one of the most recognized radiators in WW1. It is one of the components that defines the SE5a. The original SE5a has seen multiple radiator designs used during
S.E.5a (Build Instructions)
S.E.5a (Build Instructions) Specifications Wingspan: 38 cm Length: 31cm Flying Weight: 41 Channels: 3 (Rudder Elevator Throttle) Suggested Receiver: 3Ch Brick Motor: 7mm Geared Motor Airframe Only Kit
BUILD YOUR OWN. Pack 22
BUILD YOUR OWN TM Pack 22 01 CONTENTS Assembly Guide 339 Stage 70: The front brake lever Stage 71: The oil hose and the twistgrip Stage 72: Fitting the front fork assembly Editorial and design by Continuo
M o b i l e " S e a g u l l "
1 0 0. 0 5 4 M o b i l e " S e a g u l l " CONTENTS 1 Plywood Sheet (A -body) 10 x 100 x 500 mm 2 Plywood Sheet (B-Wings) 5 x 200 x 590 mm 1 Dowel ø 15 x 500 mm 1 Dowel ø 6 x 50 mm 1 Wooden ball ø 30 mm
Wing. Gently bend the top of the wing over. With the paper removed, it should produce a nice curve.
Fuselage Remove the paper in the four areas shown. Basically, from the trailing edge of the canard forward in the three nose segments and on the rear bottom of the fuse. Normal B fold for the sides but
Piper Cherokee /3 scale. Construction Manual
Piper Cherokee 140 1/3 scale Construction Manual STAB CONSTRUCTION 1. Remove foam cores from cradle and place on flat surface. Inspect pieces before you epoxy halves together making sure leading and trailing
10. Wing prep and subassembly
Date Section Objective: Construct and fabricate the sub-assemblies of the wing panel. Required Parts: Wing left 11gal PN104-300, Wing right 1gal PN104-400, Wing left 15 gal option PN104-322, Wing right
Kentucky 4H Wood Science Plans Notebook. Plans Level 1
Kentucky 4H Wood Science Plans Notebook Plans Level 1 MATERIALS NEEDED: 1 piece wood 3/4" x 2 x 2 1 piece wood 3/4" x 3 x 3 1/2" 1 wooden spring-type clothespin 2-1 1/2" nails 1-1/2 woodscrew Wood Glue
Your kit contains the following parts. Please check your kit for any missing or damaged parts before starting construction.
Your kit contains the following parts Please check your kit for any missing or damaged parts before starting construction COMPLETE KIT PARTS LIST 1 Plan Sheet #1 1 Plan Sheet #2 2 Decal Sheet 2 White Tissue
A Day House. A View of One Way to Finish the Exterior of The Day House. Read these instructions all the way through before beginning this project.
A Day House A View of One Way to Finish the Exterior of The Day House Read these instructions all the way through before beginning this project. General Comments For the purposes of this project, the standard
Installing your new Bevella Top. L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls)
Installing your new Bevella Top L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls) Bevella RTI Countertops are engineered and manufactured to the highest quality standards, built
Build your own. Pack. Stages 19-22: Continue building Robi s left arm
Build your own Pack 06 Stages 19-22: Continue building Robi s left arm Build your own All rights reserved 2015 Published in the UK by De Agostini UK Ltd, Battersea Studios 2, 82 Silverthorne Road, London
Vivian Mansion Assembly Instruction By Laser Dollhouse Designs
Vivian Mansion Assembly Instruction By Laser Dollhouse Designs NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also
GE Monogram. Installation. Instructions. Microwave Oven. Under Cabinet Installation. and. JX827 Series Built-In Kit. Models.
GE Monogram Installation Instructions Under Cabinet Installation and JX827 Series Built-In Kit Models ZEM200 Series CAUTION WARNING Before you begin Read these instructions completely and carefully. IMPORTANT:
STICK 2 IT. Fuselage Construction:
RCCD 2014 CLUB PROJECT STICK 2 IT Fuselage Construction: The fuselage is constructed without the use of a set of plans. The fuselage will be constructed on your previously prepared work surface and by
TANDY WALKER'S A 2nd CLASS BOMBER 10 to 20. FW:10 Class A Bomber LG. FW:11 Class A Bomber Pylon Primary Sructure
TANDY WALKER'S A 2nd CLASS BOMBER 10 to 20 FW:10 Class A Bomber LG I finished up the landing gear (LG) this morning and shot a couple of pictures for you to see. The first picture shows the LG with 3/32"
Stearman PT-17 KIT WARRANTY
Stearman PT-17 KIT # K-306 Assembly Instructions Version 2 02-17-16 Designed by Tom Herr WARRANTY Sig Manufacturing Co, Inc. guarantees this kit to be free from defects in both material and workmanship
Specifications Wingspan: 43cm Flying Weight: 33 grams (with battery) Channels: 3 Suggested Receiver: 4Ch Micro Motor: 7mm Brushed Geardrive
Specifications Wingspan: 43cm Flying Weight: 33 grams (with battery) Channels: 3 Suggested Receiver: 4Ch Micro Motor: 7mm Brushed Geardrive Airframe Kit (Included Contents) * Airframe Parts Sheets (Depron)
15 Dovetail Jig. Instruction Manual. Part # 3452
15 Dovetail Jig Instruction Manual Part # 3452 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools. Peachtree Woodworking
RSM DISTRIBUTION Presents
RSM DISTRIBUTION Presents MOSQUITO By Jack Sheeks Photo _ Jack Sheeks Semi Scale Twin Stunter Wing Span: 58" Length: 37-3/4 Area: 579 sq. in. Engine: Two.35 -.40 www.rsmdistribution.com Call (951) 678
Print template tiles and put together with clear tape to complete template.
Print template tiles and put together with clear tape to complete template. Cut each pattern out with scissors or use a razor and strait edge ruler. Use the ruler as a guide for the razor to get nice strait
SASKATOON, Saskatchewan
CONSTRUCTION GUIDE AVRO ARROW (CONTEST VERSION) Copyright, Bill Jones, 2004 SASKATOON, Saskatchewan This is a work in progress, so there are a couple of rough areas ( I ll point out those that I m aware
Framework joints FABRICATION - WOOD JOINTS. Corner joints. Tee joints. Worksheet 15a. Cable Educational Ltd
FABRICATION - WOOD JOINTS The word: fabricate means to join together. Most wooden products are held together with adhesive. Adhesive works very well when the edge of a piece of wood is being glued to the
Shop-Made Miter Clamps
*Editor s note: In the photos showing the table saw, the blade guard has been removed for clarity. I try to be as self-sufficient as possible, so I like to manufacture my own tools whenever I can. I designed
Extendable Large Dovetail Jig
Extendable Large Dovetail Jig Instruction Manual Part # 3458 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools.
HARRISON S HARDWARE PF5891
1:48 BUILDING KIT HARRISON S HARDWARE PF5891 Model the local hardware store where layout residents can find all they need to keep their homes in tip-top shape and workshops running smooth. The positive
1. Build the bottom first - make sure your table is flat. Build the entire plane using foam safe CA and kicker. The best technique is to spray kicker
Wxá zç uç `tçué 1. Build the bottom first - make sure your table is flat. Build the entire plane using foam safe CA and kicker. The best technique is to spray kicker on one part and apply a sparing amount
Taylorcraft Indoor / Cul-De-Sac Flyer
Taylorcraft Indoor / Cul-De-Sac Flyer Taylocraft Specifications Wingspan: 28.0 in. Wing Area: 117 sq. in. Weight (Ready to Fly): 3.0 3.1 oz. Wing Loading: 3.7 3.8 oz. / sq. ft. LIABILITY RELEASE In that
ParkJet Builder s Manual
ParkJet Builder s Manual Thank you for purchasing the ParkJet. The ParkJet is a profile ducted fan airplane that can be flown in a larger park. The ParkJet was initially designed by Scott Stoops and modified
Side Light Frame Pack Assembly Instructions
Please read this complete set of assembly instructions before starting the installation and only when you understand the construction method start to follow the step by step guide. IDENTIFY THE PACK CONTENTS
Central New York Rocket Team Challenge 2018 Rocket Assembly Instructions
Central New York Rocket Team Challenge 2018 Rocket Assembly Instructions Note: These instructions vary from those provided by the manufacturer of the rocket kits. There is also considerable varying discussion
Curium 19H Installation Instructions & Parts List
Curium 19H Installation Instructions & Parts List Illustration Curium 19H Right Hand Page 1 of 15 01/07/2016 Revision 2.1 IMPORTANT This shower screen / enclosure must be installed by suitably qualified
High performance 90mm fiberglass jet
High performance 90mm fiberglass jet Assembly manual For intermediate and advanced fliers only! Specs Wingspan: 1255mm Fuselage length: 1250mm Flying weight: 2600-3000g Wing area: 22.6 dm² Wing loading:
PITTS S2S CONSTRUCTION
PITTS S2S CONSTRUCTION FUSELAGE CONSTRUCTION 1) Place the right fuselage side over the plan and mark the former positions. Place the left side over the right side and mark the former positions. Glue F1
FireFighter.21 Building Instructions
A Tom Moorehouse design. Thank-you for purchasing the FireFighter.21. I believe that you will find it to be the best.21 rigger kit available. It has won 1 st place in the 2006 AMPBA nationals! It was designed
1Smooth pieces 4, 5 and 6, using
Yamato: Step-by-step 109 Machine-guns, anti-aircraft guns and decking h e f a b c g d e f a Anti-aircraft gun base x 2 b Anti-aircraft gun (bottom) x 2 c Anti-aircraft gun (top) x 2 d Machine-gun base
Big Oz. Rocket. User Guide V0313
Big Oz Rocket User Guide 59824 V0313 Materials Included The Big Oz Rocket Kit should include the following materials. If something is missing, contact Customer Service at 800-358-4983. 20-ounce plastic
Side Light Frame Pack Assembly Instructions
Side Light Frame Pack Assembly Instructions Please read this complete set of assembly instructions before starting the installation and only when you understand the construction method start to follow
NASTY Build Guide. Supplies needed
NASTY Build Guide Supplies needed Blucore or Depron Foam. Blucore (Fan Fold Foam) is available at Lowes. Approximately $25 for 50 feet of Blucore. Depron can be ordered on the internet for slightly more.
COMET 24" HELLCAT REPRODUCTION ASSEMBLY GUIDE
COMET 24" HELLCAT REPRODUCTION A RUBBER POWERED 24" WING SPAN MODEL BY PAUL BRADLEY ASSEMBLY GUIDE AUGUST 2016 CHANGES MADE TO THE ORIGINAL The following changes were made to the original Comet kit structural
96 WING SPAN SPITFIRE (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED
96 WING SPAN SPITFIRE (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED GENERAL INSTRUCTIONS Should you elect to use the recommended Door Skin, which is 1/8 mahogany plywood measuring 36 x 88. Have it cut
Dandy Sport Builder s Manual
Dandy Sport Builder s Manual Thank you for purchasing the Dandy Sport. The Dandy Sport has been designed as an easy to build aileron trainer. Take your time and enjoy building this plane. Specifications:
Slimline Pro Single Tube Click Pen
Slimline Pro Single Tube Click Pen Contributed by: Tom Wilson A.K.A Jolly Red This tutorial was downloaded from http://www.penturners.org The International Association of Penturners - 2016 MAKING THE SLIMLINE