Assembly Instructions to make the box organiser for the board game Perditions Mouth
|
|
- Millicent Reed
- 5 years ago
- Views:
Transcription
1 Assembly Instructions to make the box organiser for the board game Perditions Mouth With a craft knife and sandpaper, remove the pieces from the sheets of plywood as you do each tray. The pieces are almost fully cut out and have tiny joints to hold them in place while in transit. Remove the required pieces and then lightly sand any rough edges that may occur when removed. This will help to gain a better fit with the joints and make your insert stronger and smarter. Identify the pieces from the plan above. TIP. Sometimes parts of the plywood kit can be bent or warped, a weight such as a heavy book is all that s needed together with rubber bands to hold the assembly flat while the glue sets, clamps are great if you have some. Follow the instructions and you will find it much easier than removing all the pieces first into a heap. Layout the pieces of the map board holder as shown. These pieces will be found on sheets 3,18,19 and 20. Fit the four sides together and strap with rubber bands while the glue sets. Lay out the pieces of the token tray. The pieces can be found on sheets 4,5,6,7 and 8. Now fit the sides. Fit the four dividers as shown. Fit the central divider. Now fit the short divider and the tiny one, as shown.
2 Finish the tray by fitting the final two dividers as pictured. keep the contents in place. NOTE When the glue has set, there is a small adjustment that is required to allow the lid to fit. Place the lid into the locating cutouts and you will see a small piece needs to be removed with a sharp craft knife. Mark the edge with a pencil or pen. Mark with the pencil the extension of the horizontal cutout, as pictured. The plywood will cut easily. It is best to make the small cut down first, as pictured above, before the horizontal cut but please take care by removing a small amount at a time. Lay out the next box and its parts as shown. The pieces are found on sheets,11 and 12. Carefully dab small amounts of glue between the cut out holes. Now locate the sheet with glue applied onto the base. keep the contents in place.
3 Lay out the next box and its parts as shown. The parts are found on sheets, 1,3,4,8,11 and 16. Apply glue as shown on last box and locate it on the base as shown. Apply glue carefully to the underside of the cut out frame and locate as shown. keep the contents in place. Layout the pieces as shown. Parts are found on sheets, 16 and 17 Fit the four sides to complete Lay out the parts as shown, these parts are found on sheets,13,15,17 and 20 As previously done apply glue to the underside of the cut out frame and locate on the base.
4 Fit the four sides as shown. Apply glue between the five shapes pictured and fit the piece with the cutouts on the top as shown. Fit the assembled Rotikka holder into the slot on the side then fit the divider that keeps the Demon in its space. keep the contents in place. The Foam needs to be laid in the top of the tray marked where the divider is, for the demon space, then cut just enough to allow the divider to pass through. Lay out as shown, these are found on sheets, 8,9 and 10 Apply glue and fit the three overlays together, making sure the locating lugs are aligned together, then fit them onto the main base of the box. keep the contents in place. You will find that the Lay out the pieces as shown for Victims and kickstarter. Pieces can be found on sheets,14,15 and 17.
5 Apply glue and fit the cutout section as show keeping the locating lugs in position on the base Fit the four sides. Finish by fitting the divider as shown. This box has the small piece of foam to help keep the contents in place. Layout the parts of the small card holder as shown. Now do the same with the four larger card holders. Glue the ends and sides together as pictured.
Scissor Stool. Written By: Feitan
Scissor Stool If the stool is going to be kept indoors simply rub all the pieces with a Minwax WipeOn Poly before assembling the stool. If it is going to go outdoors use Minwax SparUrathane and coat all
More informationBuild the Spitfire: Step-By-step. Pack 3 Stages 21-30
Pack Stages 2-0 Contents Stage Page Number 2 72-74 22 75-78 2 79-8 24 82-84 25 85-88 26 89-9 27 92-94 28 95-97 29 98-00 0 0-05 Editorial and design by Continuo Creative, 9-4 North Road, London N7 9DP All
More informationPiper Cherokee /3 scale. Construction Manual
Piper Cherokee 140 1/3 scale Construction Manual STAB CONSTRUCTION 1. Remove foam cores from cradle and place on flat surface. Inspect pieces before you epoxy halves together making sure leading and trailing
More information(Build Instructions)
(Build Instructions) Specifications * Wingspan: 58cm * Length: 50cm * Flying Weight: 59 grams * Channels: 3 (Rudder Elevator Throttle) * Suggested Receiver: 4Ch Micro * Motor: 8mm GearDrive * Prop: GWS
More informationBuild the Spitfire: Step-By-step. Pack 7 Stages 61-71
Pack 7 Stages 61-71 1 Stage Contents Page Number 61 212-215 62 216-218 63 219-221 64 222-224 65 225-228 66 229-231 67 232-235 68 236-238 69 239-241 70 242-245 71 246-249 Editorial and design by Continuo
More informationSky Eagle. User Guide. Cautionary and Warning Statements
Sky Eagle User Guide 60089 V0613 Cautionary and Warning Statements This kit is designed and intended for educational purposes only. Use only under the direct supervision of an adult who has read and understood
More informationRESolution V2 Manual
RESolution V2 Manual Note for the German Manual: Yellow Bottle thick CA Pink Bottle Med CA Blue tube 5 minute Epoxy Green tube 90 Minute Epoxy Construction of the Fuselage Step 1: Cover the plan with a
More informationthe wire, less is better. And make sure the bends on each truss wire are in line with the other. See the next photo.
The following information and photographs are what I did to build the kit. Your methods and needs may differ from this which is fine. There is no right or wrong way if you are used to scratch building.
More informationSection # /2" x 1 1/2" x 20" /4" x 15 3/4" x 82 1/2" /4" x 1 5/8" x 82 1/2"
Hardware & Miscellaneous Items: A 2 3 1/2" chest handles B 7 3" T-hinges and screws C 4 1/4" T nuts D 4 1/4" x 2 1/2" Carage bolts E 2 1/4" x 2" Barrel Bolts F 2 1" x 5' Straps G 8 1/4" 3 1/2" Carage Bolts
More informationBig Oz. Rocket. User Guide V0313
Big Oz Rocket User Guide 59824 V0313 Materials Included The Big Oz Rocket Kit should include the following materials. If something is missing, contact Customer Service at 800-358-4983. 20-ounce plastic
More informationFLITZEBOGEN-2 Assembly instructions
FLITZEBOGEN-2 Assembly instructions Trim the end of the fuselage to the length of 925mm from the nose. Be careful to avoid splitting the carbon fibers. Sand the base of the stab mount in preparation for
More informationBUILD THE. Soleil Royal. Pack 1. The flagship of King Louis XIV.
BUILD THE Soleil Royal The flagship of King Louis XIV www.model-space.com Pack 1 Stage 1 Assembly Guide Hull frame, false keel and first deck half A 4 2 5 1 6 7 1A Smooth the surfaces of all the pieces
More informationModern Gas Station backdrop building kit in HO scale
Modern Gas Station backdrop building kit in HO scale This kit includes all building parts, pumps, signs, and base milled in white styrene plastic, clear window glazing, Plastruct Ridgid Clay Tile roofing,
More informationPrecut Wingola Kit Instructions
Precut Wingola Kit Instructions Below is the precut option. Battery compartment, Receiver and Servo Trays are cut for mini radio gear. This is the uncut version. It has the placement laid out for the radio,
More informationContents. Build the Spitfire: Step-By-step
Pack 2 Stages -20 Contents Stage Page Number 8-0 2 - - 7 8-50 5 5-5 6 5-57 7 58-60 8 6-6 9 6-67 20 68-7 Editorial and design by Continuo Creative, 9- North Road, London N7 9DP All rights reserved 20 De
More informationInvisible Clip Tutorial
Invisible Clip Tutorial I first saw what I call the Invisible Clip in Russ Fairfield s PMG gallery and fell in love with it. I could not figure out how he made them so I sent him an e-mail and he was kind
More informationEXTREME LOAD no. TWO
1602 - EXTREME LOAD no. TWO Kit Features: 22' 4 " x 14' x 3'-6 Oversize Load 49mm (1.9") actual height Bolt Head Details Welded Load Mounting Fins Painting Handles Tools Required: Hobby Knife Tweezers
More informationSASKATOON, Saskatchewan
CONSTRUCTION GUIDE AVRO ARROW (CONTEST VERSION) Copyright, Bill Jones, 2004 SASKATOON, Saskatchewan This is a work in progress, so there are a couple of rough areas ( I ll point out those that I m aware
More informationMousetrap Catapult. About this project:
Designed by: Ritchie Kinmont Project #44 Page 1/19 About this project: The is fun for ages four and up. Using a mousetrap for the spring, this catapult is designed to throw objects such as practice golf
More informationModel Grandma and Grandpa s cozy cottage, a. Country Cottage Instructions HO Scale 1:87 WOODLAND SCENICS PF5186
PF586 Country Cottage Instructions HO Scale :87 Model Grandma and Grandpa s cozy cottage, a young family s first home or give this vintage Victorian cottage the run-down look of an abandoned shack. This
More information#P570 - Leavenworth Requires a pendulum movement kit (#A309 - #A312) 24 H x 14 W
- Leavenworth Requires a pendulum movement kit (#A309 - #A32) 24 H x 4 W Cut on dashed line for Back Cut on solid line for Frame only. Stock: /8 - /4, cut each Left pattern piece. GENERAL SCROLLSAW TIPS
More informationGeneral Purpose Flat Wagon
General Purpose Flat Wagon This is a freelance model of a flat wagon used by any number of railways for transporting large and awkward loads. The kit includes optional load securing rings and a pair of
More informationHow to Construct the 8-Point Star by Jay S. Helland
How to Construct the 8-Point Star by Jay S. Helland 1-5-2013 The photos in these instructions were not taken in consequential order but provide the reader the general idea of the processed used. The process
More informationSeascape Bungalow Assembly instructions. Laser Dollhouse Designs
Seascape Bungalow Assembly instructions Laser Dollhouse Designs NOTE: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also
More informationSZD-10 bis CZAPLA ASSEMBLY MANUAL IN PICTURES
1 RUDDER Plan and parts: 2 Assembly steps: Photo above: glue together rudder spar, ribs and trailing edge. Clamp spar to a flat surface (chipboard on the photo) and make sure the straight aligment of the
More informationFireFighter.21 Building Instructions
A Tom Moorehouse design. Thank-you for purchasing the FireFighter.21. I believe that you will find it to be the best.21 rigger kit available. It has won 1 st place in the 2006 AMPBA nationals! It was designed
More informationCA to each one. You may have to hold the end down while to glue sets or use an accelerator like I did.
The following information and photographs are what I did to build the kit. Your methods and needs may differ from this which is fine. There is no right or wrong way if you are used to scratch building.
More informationHobby Lobby Zip Supplementary instructions Please refer to the included drawings while using these assembly instructions
Materials needed: 15 or 30 minute epoxy Medium CA Masking tape Scotch tape Servo Tape Wax paper Tools Needed: Pencil or marker Flat building surface Hobby knife or razor blade 7/64" or 3mm drill bit 3/16"
More informationFidelity & Guaranty Building
Fidelity & Guaranty Building N Scale Model Kit Instructions for Assembly of the Fidelity & Guaranty Building Kit Contents: 69 each laser cut acrylic parts. Sidewalk material 1 each Window Glass Templates
More informationHudson Dresser [1] Hudson Dresser Published on Ana White ( Submitted by dan-k [2] on Fri, :43 [1]
[1] Submitted by dan-k [2] on Fri, 2011-03-11 11:43 [1] If you plan on staining this piece, it is recommended that you stain all of the drawer face materials before assembly for a more professional look.
More informationFidelity & Guaranty Building
Fidelity & Guaranty Building Instructions for Assembly of the Fidelity & Guaranty Building Kit Contents: 69 each laser cut acrylic parts. 1 each sheet of AC roof unit parts. 1 each sidewalk base. 4 each
More informationCorona Concepts presents The Laurel All Wood Dollhouse. Instructions and Assembly Guides
Corona Concepts presents The Laurel All Wood Dollhouse Instructions and Assembly Guides Introduction In Short... Welcome to the exciting world of dollhouses and miniatures. Since the first tab and slot
More informationInstallation Guide 1
1 2 Contents Before you begin Storage & preparation Tools & materials you may need Getting started Sink & cooktop cut-outs Cabinet Joins for 20mm benchtops Joining & installation of 20mm benchtops Joining
More informationFUSELAGE CONSTRUCTION
FUSELAGE CONSTRUCTION Note: prior to building and gluing on the work surface use protective covering on your building surface. (wax paper or clear wrap) Fit the laser cut Fuselage Front and Fuselage Rear
More informationALIEN ENCLOSURES CAMARO AND FIREBIRD Trunk Panel Kit Instructions
ALIEN ENCLOSURES 67-69 CAMARO AND FIREBIRD Trunk Panel Kit Instructions TYPICAL TOOLS & MATERIALS NEEDED FOR UPHOLSTERY 2 Yards of Main Panel Material 1.5 Yards of Backer Material 3 yards of foam backing
More informationCABINETRY Assembly Instructions
www.hdicabinetry.com Assembly Instructions TABLE OF CONTENTS Category Page(s) Section 1: Framed Series Base Cabinet Instructions Wall Cabinet Instructions Easy Reach Cabinet Instructions 1.01-1.04 1.05-1.06
More informationCopyright 2010 Springbok Publishing All Rights Reserved- Page 1
Copyright 2010 Springbok Publishing All Rights Reserved- www.woodensaddlerackplans.com Page 1 Legal Information All contents copyright 2010 by Springbok Publishing. All rights reserved. No part of this
More informationProject Skill Level: INTERMEDIATE Plywood Used: CANPLY EXTERIOR Good Two Sides (G2S) or precision sanded Aspen
Project Skill Level: INTERMEDIATE Plywood Used: CANPLY EXTERIOR Good Two Sides (G2S) or precision sanded Aspen MATERIALS LIST: (1) ¾" x 4 ft x 8 ft plywood panel (20) #8 x 2" Robertson or Phillips wood
More informationSlide the stock rubber tank mount caps onto the ends of the CS-1 tank mount:
RYCA CS-1 BODY PARTS INSTALLATION GUIDE [The CS-1 installation guides should be used as supplements to the videos found on our Youtube Channel. There is no strict order to the build process, but it is
More informationLittle Briana Cottage Dollhouse assembly instructions
Little Briana Cottage Dollhouse assembly instructions NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also gives
More informationLUNAR EXPRESS. Little
Little LUNAR EXPRESS The Little Lunar Express kit contains all the parts necessary* to build a flying high power rocket: 1) Pre-slotted boattail 1) Airframe 5.5" long 1) Nose cone 2) Main fins 2) Stabilizer
More informationSPORTSTER BY FRED TUXWORTH
SPORTSTER BY FRED TUXWORTH For those who like gas models to look like real airplanes, this sturdy performer is just about tops. Best -looking model of the year Biplane wings may be fitted. This gives you
More information1Take the keel (3) and
1 The hull and the bridge 1Take the keel (3) and apply PVA wood glue in the second slot from the left: a toothpick may make it easier. Take care: the left end is the one that has a projection. THE HULL
More informationDIY CROWN MARACAS DISNEY
DIY CROWN MARACAS YOU WILL NEED: For the crowns: 3 clean tea tins (or hot cocoa tin, seasoning containers, etc. Anything cylindrical with a lid) Gold glitter paper or vinyl Various jewels & gems Filling:
More informationModel the hub of your layout s rural setting. Planters Feed and Seed Supply Instructions N Scale 1:160 WOODLAND SCENICS
PF5201 Planters Feed and Seed Supply Instructions N Scale 1:10 Model the hub of your layout s rural setting. Planters Feed and Seed Supply presents a vintage agricultural center where farmers and rural
More informationOption 1: False Frame Bent
Black Bear Construction Co. www.blackbearcc.com Standard and Narrow Gauge railroads are often used in industrial or short line operations. These areas often require drainage that can be provided by trestles.
More informationHow to assemble the Reims Gueux Pit Centre Module #005
How to assemble the Reims Gueux Pit Centre Module #005 We recommend quick drying super glue for our models. Just a few drops on the joining edges, press and hold them for a few seconds and the connection
More informationAssembly Instructions for Busted Bricks Marble Machine #1
Assembly Instructions for Busted Bricks Marble Machine #1 Ver. 2 instructions Page number 1 Required for assembly: Wood glue (PVA or aliphatic resin recommended) and/or Cyanoacrylate (CA) glue Clamps or
More informationINCLUDED IN THIS KIT: SPECIFICATION: NEEDED BUILDING TOOLS: REQUIRED EQUIPMENT:
Please review this entire manual before beginning assembly. By doing so it will help you better understand each step as you progress in the actual building of your kit, and you will do a better job in
More informationEXTREME LOAD no. ONE
P R E C I S I O N D E S I G N C O 1601 - EXTREME LOAD no. ONE in HO scale Kit Features: 18'-8" x 7'-1" x 18'-9" Oversize Load 65.62mm (2.583") actual height Bolt Head and Bolt Hole Details Welded Load
More information3Insert the second rod no. 4
Yamato: Step-by-step 37 The stern block and searchlight control towers a b c d e f Recommended tools and materials Wood glue Sandpaper (no. 800 grain) Metal file Putty Craft knife For metal: Super Glue
More informationHRMLaserModels.com T.W. SNOW 25 TON COALING TOWER S SCALE AS USED ON THE MILWAUKEE ROAD
HRMLaserModels.com T.W. SNOW 25 TON COALING TOWER S SCALE AS USED ON THE MILWAUKEE ROAD HRM-61 S SCALE COAL TOWER T.W.Snow 25 Ton Coaling Tower General Instructions Check out HRMLaserModels.com for construction
More informationSan Felipe: Step by Step Pack 3
Pack 3 Your parts Bulwarks Gun port covers x 2 Tools and equipment Wood glue Sandpaper Brushes Wood stain Hammer Pin pusher/nails Razor saw a Remove the longer bulwark and test-fit it in place at the bow
More informationULTRA-TOTE BASIC INSTRUCTION MANUAL
ULTRA-TOTE BASIC INSTRUCTION MANUAL Thank you for purchasing the Ultra-Tote Basic! You have purchased one of the finest values available in field support equipment. We think you will be impressed with
More informationSeamed Undermount Bowls
CUTOUT TEMPLATES MAKING CUTOUT TEMPLATES 7.1 CUTOUT TEMPLATES The use of an accurate template is one of the most essential elements to the successful completion of a cutout in Corian. For the completion
More informationThis article was written by Phill Brander (AUS), who has built many timber catamarans including a Paper Tiger.
Building a Paper Tiger Catamaran Scarfing Plywood Paper Tiger Catamaran GUIDES Warnings/Cautions As always, using any power tools, cutting implements or adhesives carries certain risks. Make sure you understand
More information1999 Combat Wing Trick R/C Products LLC 938 Victoria Ave. Venice, California 90291
1999 Combat Wing Wing Span 48" Wing Area 2.83 SqFt Airfoil Zagi 99 Weight 18/23 oz Loading 7 oz/sq.ft Radio 2 channel or mixer Speed Range Wind: 6 to 45 mph Visit: ZAGI.com Email: Zod@Zagi.com Voice: (310)
More informationThe Saint Paul Building
The Saint Paul Building Instructions for Assembly of The Saint Paul Building. Kit Contents: 65 each laser cut acrylic parts. 1 each sheet of AC roof unit parts. 1 each sidewalk. 3 each Window Glass Templates,
More informationFor Barrel Tapers. Installation and Operating Instructions For use with small combination belt & disk sanders. Assembled Taper Tool
Tim s Taper Tool For Barrel Tapers Installation and Operating Instructions For use with small combination belt & disk sanders Assembled Taper Tool Your taper tool is capable of making barrel tapered shafts.
More informationTools and Tips: ( 1 )
Tools and Tips: As you build instructions will show in my many picture manual how to assemble. You can use your own methods as you desire, my results are very good. A smooth, flat work surface is very
More information1Smooth pieces 4, 5 and 6, using
Yamato: Step-by-step 109 Machine-guns, anti-aircraft guns and decking h e f a b c g d e f a Anti-aircraft gun base x 2 b Anti-aircraft gun (bottom) x 2 c Anti-aircraft gun (top) x 2 d Machine-gun base
More information(56501) Corona Concepts presents The Willow All Wood Dollhouse. Instructions and Assembly Guide RTD AA
(56501) Corona Concepts presents The Willow All Wood Dollhouse Instructions and Assembly Guide RTD10000572AA Introduction In Short... Welcome to the exciting world of dollhouses and miniatures. Since the
More informationAssembly instructions for the Simple Marble Machine
Assembly instructions for the Simple Marble Machine Page number 1 Parts layout Page number 2 Please note: All the assembly can be done with PVA glue. Don't apply it from the bottle or tube but put a blob
More informationSmall 45 Roof Houses 1 or 2 Story 1 /24 th Scale Patterns
BA GARDEN TOWNS 45 Roof Houses 10" x 10" 1 or Story Scaled and easy to read patterns and instructions for wood houses. Yard and Garden Buildings Compatible with Garden Railroads or a delight for any child's
More informationWooden Plane. Hardware Kit. 05P Blade packaged separately.
Wooden Plane Hardware Kit Veritas Tools Inc. Ottawa ON K2H 1C2 Canada Ogdensburg NY 13669-2205 United States www.veritastools.com 05P40.45 W22356p@AEBHe Blade packaged separately. Introduction The following
More informationBuild the Spitfire: Step-By-step. Pack 4 Stages 31-40
Pack 4 Stages 31-40 1 Contents Stage Page Number 31 106-108 32 109-111 33 112-115 34 116-118 35 119-122 36 123-125 37 126-128 38 129-132 39 133-136 40 137-139 Editorial and design by Continuo Creative,
More informationTrumpet : Assembly Instructions
A trumpet is a brass instrument which is played by blowing air into the mouthpiece and causing vibrations with the lips, while operating piston or rotary valves. A trumpet's shape and the length of its
More informationPachinko Machine. Supplies: Part One: Construction. Optional: (1) 21" x 15.5" piece of wood. jumbo craft sticks. (2) 17" x 1" pieces of wood
Supplies: (1) 21" x 15.5" piece of wood jumbo craft sticks (2) 17" x 1" pieces of wood standard craft sticks (2) 14.5" x 1" pieces of wood 1" wooden craft circles (2) 4" x 2" pieces of wood drill (1) 14.5
More informationOutdoor Cooler Cart. Outdoor Cooler Cart Construction Instructions
Outdoor Cooler Cart Outdoor Cooler Cart Construction Instructions Make the Legs and Side Panels. Cut the eight long and short leg pieces to length. See Material List on next page.. Apply a bead of glue
More informationCentral New York Rocket Team Challenge 2018 Rocket Assembly Instructions
Central New York Rocket Team Challenge 2018 Rocket Assembly Instructions Note: These instructions vary from those provided by the manufacturer of the rocket kits. There is also considerable varying discussion
More informationHotel Belvedere Instructions for Assembly of the HO scale kit. v1.1
Hotel Belvedere Instructions for Assembly of the HO scale kit. v1.1 Kit Contents: 319 ea. laser cut.090" acrylic parts. 132 ea. laser cut.060" acrylic parts. 8 ea. window glass templates 8 ea. window glazing
More informationHomemade Weaving Jig By David Dosser
Homemade Weaving Jig By David Dosser Items needed for a 100 thread weaving jig: 1. 8x10 -.080 Plastic sheet (Optix brand or Lexan). Clear or white Plastic is easier to work with and can be found at most
More informationSmall Town Buildings. Scaled and easy to read patterns and instructions. Shoe / Western Union (with and without porch)
1 /24 th Scale Patterns kiva design G R O U P E 1 Story Flat Roof Yard and Garden Buildings Compatible with Garden Railroads or a delight for any child's collection Overall Dimensions Foundation: 10" x
More informationAmerica s leading woodworking authority To download these plans, you will need Adobe Reader installed on your computer. If you want to get a free copy, visit: http://adobe.com/ reader. Having trouble downloading
More informationBlock Frame Inovo Patio Door/Transom/Sidelite Field Mulling Instructions. simonton.com/installation. If mulling sidelites, skip to Step 5.
Effective Date: 10/1/17 Tools Needed Kit Contents Safety Glasses Cordless Drill Phillips Screw Bit Two-step Drill Bit (3/8-1/8 ) Utility Knife Interior Mullion Exterior Mullion Cover Hardware Kit Clamps
More informationAFCO-Rail Post INSTALLATION INSTRUCTIONS AFCO-RAIL POST
AFCO-Rail Post INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Drill Bits (for the appropriate fastener) Drill (with adjustable clutch, recommended) Level String Line Tape Measure Tools to install fasteners
More informationHubble Space Telescope Paper Model Directions Downloads, patterns, and other information at:
Hubble Space Telescope Paper Model Directions Downloads, patterns, and other information at: www.hubblesite.org/go/model Materials: model pattern printed onto cardstock/coverstock instructions printed
More informationThe Rubley Building Instructions for Assembly of the N scale kit. v1.1
The Rubley Building Instructions for Assembly of the N scale kit. v1.1 Kit Contents: 197 ea. laser cut 1/16" acrylic parts. 1ea. adhesive backed.020 styrene part. 10 ea..060 x 1" styrene alignment pins.
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 1
Kentucky 4H Wood Science Plans Notebook Plans Level 1 MATERIALS NEEDED: 1 piece wood 3/4" x 2 x 2 1 piece wood 3/4" x 3 x 3 1/2" 1 wooden spring-type clothespin 2-1 1/2" nails 1-1/2 woodscrew Wood Glue
More informationSE5a Wing Panels rev 1.0
SE5a Wing Panels rev 1.0 The top and bottom wings are different. They might look the same but the bottom wing has one less rib and some rib spacing difference. This is due to where the wooden interplane
More informationSpiderbeam Balun Construction Guide
BALUN CONSTRUCTION GUIDE Ver. 1.0 1 The components of the Balun Kit are in a plastic bag. Most of the components are inside the plastic case of the balun. The aluminum U-profile and the RG-142 Teflon Coax
More informationPROJECT PLANS WOODEN GIFT BOX
PROJECT PLANS WOODEN GIFT BOX Make the gifts you give even more special by presenting them in this one-of-a-kind gift box. In fact, the box may be valued more than whatever it contains. The box is sized
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 3
Kentucky 4H Wood Science Plans Notebook Plans Level 3 MATERIALS: 2 pieces wood 3/4 x 10 x 4 1 piece wood 3/4 x 12 x 4 2 pieces wood 3/4 x 3 x 2 5 1/2" 2 pieces wood 3/4 x 3 x 1 8 1 piece wood 2 x 4 x
More informationC-Series & S-Series Classic Frame with Transom (Single or Pair)
1. TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Safety Glasses Screw gun #2 Screwdriver tip #3 Screwdriver tip Philips Head screwdriver (Used to move frame on wall using oval slots on
More informationInstalling your new Bevella Top. L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls)
Installing your new Bevella Top L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls) Bevella RTI Countertops are engineered and manufactured to the highest quality standards, built
More informationDesk/Wall-Mount Rack
Desk/Wall-Mount Rack Patent(s) Pending Installation Instructions Post P/N: 119-1752 119-1781 119-1782 119-4014 Frame P/N: 119-1591 119-1754 119-1755 Kit Contents (2) Frames (4) Posts Assembly Hardware
More informationPILOT SEAT AND HARNESS
1. Locate the following parts PILOT SEAT AND HARNESS #84 threading needle, 1 each #88 lacing cord, 1 each #119 aluminum seat, 1 each #120 plywood, pilot seat bottom, 1 each #121 wood screw, 3 each #293
More informationMLCS Instructions for Bowl and Tray Template Kit #9176/#9179
MLCS Instructions for Bowl and Tray Template Kit #9176/#9179 Tools Needed: Router 1-1/2 h.p. Minimum recommended with a 1/2 collet Forstner bit 3/4-2 recommended depending on template used Drill Press
More informationPEAK OAK OAK FLOORING, OAK DOORS & WROUGHT IRONWARE
PEAK OAK OAK FLOORING, OAK DOORS & WROUGHT IRONWARE How To Assemble An Oak Ledged Door www.peakoak.co.uk Introduction Some of you choose to order your oak ledged doors in kit form and the following guide
More informationCopyright 1998 KDE Technologies
Modular Computer Corner Desk Unit Copyright 1998 KDE Technologies http://members.tripod.com/~kdetech/ 1. Introduction 2. Plans Sheet one - Isometric Sheet two - Top Detail / Corner Unit Sheet three - Leg
More informationWOOD COUNTERTOP INSTALLATION INSTRUCTIONS
1209 Logan Circle, Atlanta, Georgia 30318 www.craft-art.com (404)352-5625 WOOD COUNTERTOP INSTALLATION INSTRUCTIONS Required Tools and Supplies Cordless Drill Belt Sander with 60 and 80 grit belts. Shur-form
More informationMaking Simple Bookbinding Equipment
Tony Firman 20 1 2 19 Notes Tony Firman Tony Firman Bookbinding 18 3 : 2012 Tony Firman Bookbinding P.O. Box 507 Haslet, TX 76052 www.tonyfirmanbookbinding.com 4. When all the tapes have been pinned in
More informationPS 5077 cu. ft. Boxcar with EOC device. 1:29 scale resin craftsman kit. by Burl Rice
PS 5077 cu. ft. Boxcar with EOC device 1:29 scale resin craftsman kit by Burl Rice www.burlrice.com Bill of materials (not included): Thick/medium viscosity CA PL adhesive, or Gorilla Glue Heavy Duty Construction
More informationBuilding Tips This model can be built using the following types of adhesives:
Page 1 Building Tips This model can be built using the following types of adhesives: Epoxy (with or without microballons) Odorless cyanoacrylate (CA) with accelerator UHU Creativ for Styrofoam (or UHU
More information43107 Rhino Jerry Can Holder Rhino Jerry Can Holder - Horizontal
Important: Please read these instructions carefully prior to installation. Check the contents of kit before commencing fitment and report any discrepancies. Clean the alloy tray prior to installation.
More informationInstallation Manual Using Existing Handrail Version 4.0 Oct 2017
Installation Manual Using Existing Handrail Version 4.0 Oct 2017 ORDER OF ASSEMBLY TOOLS YOU WILL NEED - Fine Saw - Sander - Wood Filler - Allen keys - Screw Driver - Drill - Suitable Screws PROTECTING
More information1/6 PA-25 PAWNEE. *Specifications are subject to change without notice.*
1/6 PA-25 PAWNEE INSTRUCTION MANUAL [ A335 Kit ] Wing Span : 72 in / 1830 mm Wing Area : 736 sq in / 47.5 sq dm Flying Weight : 6.6 lbs / 3000 g Fuselage Length : 48 in / 1220 mm Requires : "Glow Power"
More information136 PLYWOOD DESK 522
136 PLYWOOD DESK 522 Simple in design and inexpensive, this plywood desk is made from a single 4- x 8-foot panel. Plywood is available with many hardwood veneers; it can also be covered with plastic laminate,
More informationCorvus Racer Colour schemes. AeroPlus RC Copyright 2013 All Rights Reserved
Corvus Racer 540 59 Item No:A E050003 Specifications WING SPAN: 59"(1500mm) LENGTH: 54.1"(1374mm) WING AREA: 654sq.in.(42.2sq.dm.) FLYING WEIGHT: 4.6 5.3lbs(2000 2300g) Electric:Brushless outrunner 8Oz.
More informationImportant Note: Why this guidebook is FREE?
Easy DIY Murphy Bed Construction Guide 1 Important Note: This guide is a FREE SAMPLE of our Complete Construction Guidebook. With the help of this guide you will get familiar with the construction steps
More information