Homemade Weaving Jig By David Dosser
|
|
- Buddy Neal
- 5 years ago
- Views:
Transcription
1 Homemade Weaving Jig By David Dosser Items needed for a 100 thread weaving jig: 1. 8x Plastic sheet (Optix brand or Lexan). Clear or white Plastic is easier to work with and can be found at most home improvement stores and some hobby stores. You may also use thin hobby wood, but plastic looks better and you can use dry erase markers for re-numbering if needed. 2. EVA foam, 6mm. Sheets can be glued together if needed to equal 6mm. This can be sheet foam found at a hobby store or the big auction website, even EVA grip foam will work if not too stiff. 3. Foam mounting tape or plastic glue. 4. Plastic u-channel (1/4 ) or other material such as brass or aluminum ¼. This example is plastic Plastruct styrene 1/4 deep u-channel from Tower Hobbies NEW razor blades or scalpel. Dull razor blades do not cut the foam as good and then the slots will not hold thread tension as well.
2 6. Your choice of tool for cutting plastic. I use a rotary tool with a thin diamond cutting wheel. Instructions 1. Cut the plastic according to the schematic. Both pieces, exact same size. Round the edges and sand any sharp or rough areas to protect the rod blank. 2. Cut the foam strips 6mm wide x 9mm high with razor or good scissors. 2 pieces, 14cm; 2 pieces 11cm. Note: You can cut the foam strips about 1 or 2mm longer than the u-channel. This will allow you to place a rubber band from one end to the other after you have placed it in the u-channel in order to squeeze the slots together for better thread tension. 3. Cut the u-channel with razor, rotary tool or hobby saw. 2 pieces 14cm; 2 pieces 11cm. 4. Mark out where the u-channel will be on the plastic bases with gel pen or wax pencil. 5. Cut and apply foam mounting tape to the bottom of the u-channels and press them onto the bases. Make sure to place them according to the diagram. 6. Optional: Apply thin strips of double sided tape to one side of the foam strips and insert them into the u-channels with an equal distance of foam slightly sticking out of both ends of the channel (for rubber bands to grab onto). 7. Cut the slots in the foam to the top (or close to the top) of the channel in each strip with a NEW razor or scalpel. Make the slots as straight and level as possible. The long strips need 11 slots per inch and the short strips need 10 slots per inch. This will give you
3 at least 60 slots on the long side and 40 slots on the short side. I used a fabric ruler with marks for different threads per inch to mark the foam. If you do not have one of these, you may have to do the math. A pencil will mark the foam for the slots, unless you use black colored foam. I use a silver gel pen for black foam. 8. At this point you can mark the plastic with a paint pen or something similar, mark the slots, or cut paper to match angles and lengths and mark numbers on the paper. I marked on graph paper every 5 th slot, cut it to fit the underside of the jig, then taped it underneath with the marks showing through. This way I can renumber the jig for smaller weaves by using a dry erase marker on top. I also dotted the every 5 th slot with a marker directly on the foam just to help me see a little better. 9. The rubber bands can be installed with half of the band on the channel and half on the foam and stretched from one end to the other on each channel. This will help pull the slots together and therefore give you a little more tension on the thread while in the slots. 10. I recommend marking each jig Left or Right (L or R). Tape the weaving jigs to the rod weave! You can make a weaving jig that holds any amount of threads you need by simply changing the number of slots per inch or shortening the whole thing. This wasn t meant to limit anyone to a 100 thread jig. I have made several of these and they work well. I use a 60 thread jig most of the time that was made the same way, just a little shorter. I use the 100 thread jig for large patterns. I have included a picture of a 100 thread jig with brass channels and graph paper taped underneath and a 60 thread jig on white plastic using equal size channel pieces and foam strips. The slots in this one were cut at 8 slots per inch. Enjoy!
4
5
6
7
8
9
10
Homemade Sanding Tools David Hoehns
Homemade Sanding Tools David Hoehns allskewedup@gmail.com 806 789 5108 My demonstration will focus on two types of homemade sanding devices, a foam ball sander that may be used for power sanding concave
More informationCurved Metal Segmenting
Curved Metal Segmenting A Tutorial by: David Washburn A.K.A djwood1 This tutorial was downloaded from The International Association of Penturners Introduction As I continue to learn about pen turning,
More informationNASTY Build Guide. Supplies needed
NASTY Build Guide Supplies needed Blucore or Depron Foam. Blucore (Fan Fold Foam) is available at Lowes. Approximately $25 for 50 feet of Blucore. Depron can be ordered on the internet for slightly more.
More information3Insert the second rod no. 4
Yamato: Step-by-step 37 The stern block and searchlight control towers a b c d e f Recommended tools and materials Wood glue Sandpaper (no. 800 grain) Metal file Putty Craft knife For metal: Super Glue
More informationHubble Space Telescope Paper Model Directions Downloads, patterns, and other information at:
Hubble Space Telescope Paper Model Directions Downloads, patterns, and other information at: www.hubblesite.org/go/model Materials: model pattern printed onto cardstock/coverstock instructions printed
More informationModern Gas Station backdrop building kit in HO scale
Modern Gas Station backdrop building kit in HO scale This kit includes all building parts, pumps, signs, and base milled in white styrene plastic, clear window glazing, Plastruct Ridgid Clay Tile roofing,
More informationCopyright 1998 KDE Technologies
Modular Computer Corner Desk Unit Copyright 1998 KDE Technologies http://members.tripod.com/~kdetech/ 1. Introduction 2. Plans Sheet one - Isometric Sheet two - Top Detail / Corner Unit Sheet three - Leg
More informationHow to Make a Hat Bending Jig
How to Make a Hat Bending Jig MATERIALS One 2" x 8" x 11" long (Base Block) exact measurements are 7 ½" x 1 ½" x 11" (Pine is OK to use, I have used scrap Walnut for my benders) Four pieces of Oak 1" x
More informationCRAFTS. London Double Decker Bus Craft
London Double Decker Bus Craft CRAFTS A double-decker bus has two levels or 'decks'. Red doubledecker buses are usually associated with London and have become a national symbol of England. This cardboard
More informationHand-Laying Turn-outs. By Brad Morneau
Hand-Laying Turn-outs By Brad Morneau 1 Index Section: Page(s) Introduction 3 Turnout basics 3 Fast-Track Templates 4 First Step: Plot the turnout 5 Drilling pilot holes 5 Lining up the Switch Machine
More informationHardee s Restaurant kit in HO scale
Hardee s Restaurant kit in HO scale Parking lot base and cars not included This kit includes all building parts milled in white styrene plastic and laser cut white acrylic, clear acrylic window glazing,
More informationMaking Double Fold Straight of Grain Quilt Binding
Making Double Fold Straight of Grain Quilt Binding Tools and Supplies: Cutting mat, rotary cutter with a sharp blade, walking foot, 6x24 ruler, seam allowance guide, pencil, quilting gloves Be sure your
More informationPATH Supply List th Grade
PATH Supply List 2018-19 8th Grade 2 boxes of tissues 2 packs of 100 3x5 index cards (Homework Binder) 16-20 tab dividers 1 spiral or composition notebook (for MG) 1 pack of at least four whiteboard markers
More informationFrom "American Woodturner" the Journal of the American Association of Woodturners, April 2015, vol 30, no 2 - CUSTOM - TOOL HANDLES
From "American Woodturner" the Journal of the American Association of Woodturners, April 2015, vol 30, no 2 - CUSTOM - TOOL HANDLES Carl Ford I have found most commercially available tool handles uncomfortable
More informationElastic-powered Bus : Assembly Instructions
Elastic-powered Bus : Assembly Instructions Assembly Instructions 1. Carefully cut out the parts. 2. Fold along the dotted lines, making mountain or valley folds as indicated. 3. Attach the glue spots
More informationBuilding the Gothic Church
Building the Gothic Church Mold #54 does not contain all of the blocks to build this church. You will need extra regular blocks (1/2" x 1/2" x 1") and square blocks (1/2" x 1/2" x 1/2"). These blocks can
More informationTips & Tricks using Part 2
Tips & Tricks using Part 2 Using the cobblestone mold #210...1 Making a dungeon diorama...2 Making torches...3 Making a textured door...4 Making a portcullis...5 Adding moss...6 Tips & Tricks using Bruce
More informationAirport Terminal Building #1 (AD-TB01-0A)
Thank you for purchasing the Airport Terminal Building #1. I know you will be pleased with the final product. Before you get started, here is a list of what you ll need: Paper. For best results I recommend
More informationSwift assembly guide
Swift assembly guide Download the assembly guide at www.scihighmodels.com/swift.pdf Sample kit shown with aluminium bells (available with the Deluxe kit) Shown here without main tanks Version 10/12/2010
More informationHow to Rip Out a Seam
Published on Sew4Home How to Rip Out a Seam Editor: Liz Johnson Friday, 07 August 2015 1:00 Mistakes happen to the best of us. Anyone who sews understands that some seams just weren't meant to be. The
More informationHow to: Steering wheel binding
How to: Steering wheel binding For Citroen D Models with bound steering wheels as fitted before 1972. By Darrin Brownhill at Citroen Classics, UK. www.citroenclassics.co.uk READ ALL OF THIS GUIDE TO MAKE
More informationSword Blade. Leave the bottom of the blade untouched so you can fit it to the crossguard perfectly.
Sword Blade Trace the pattern onto the wrong side of your foam (if there is a rougher edge) twice and use a sharp knife to cut it out. You will save foam if you make the blade fit twice onto once piece
More informationMax Launch Abort System Prod. No *Kevlar is a registered trademark of Dupont
Flying Model Parts List Max Launch Abort System Prod. No. 3014 A 11820 - Body Tube 3.5 Diam x 5.5" Long B 11824 - Orange Capsule Base Shoulder Ring C 16032 - Laser-cut Ring motor mount rear D 16033 - Laser-cut
More informationKINISTINO SCHOOL KINDERGARTEN SUPPLY LIST
KINISTINO SCHOOL KINDERGARTEN SUPPLY LIST - 1 Backpack - 1 Space Saver Pencil Case - 4 dry erase markers do not label - 1 set headphones - 1 eraser - 1 pair of children s scissors with a metal blade -
More informationA Pictorial of David Dawes AA400 HFT Thumbhole Stock in the Making
A Pictorial of David Dawes AA400 HFT Thumbhole Stock in the Making From This This To Part 1 By James Mitchell (a.k.a. mitchejc) Note: Building rifle stocks is super fun and the idea with this pictorial
More informationJohn Rumming. Making Custom Foam Inserts.
John Rumming. Making Custom Foam Inserts. I, like plenty of people out there, need foam holders for quite a few of my models that sometimes come without boxes, or just to keep them in one area in groups.
More informationSnowman Gift Box Tower Designed By: Amanda Corbet December 2011
Snowman Gift Box Tower Designed By: Amanda Corbet December 2011 This adorable snowman gift box tower is the perfect way to shower someone special with gifts. Finished as shown this box is over 16 inches
More informationSection 1, Center Section Make One. Fabric Fabric # of Cutting Directions ID Location Strips
Please read all instructions carefully prior to beginning quilt. All piecing uses a very accurate scant quarter inch seam allowance. In this quilt, accuracy is absolutely critical, so sew several sample
More informationGENERAL NOTES: Page 1 of 9
Laminating A Zia Into A Turning Blank by W. H. Kloepping, Jan. 2009 This describes how a zia (the New Mexico state symbol) can be laminated into a turning blank. Materials needed: Square Turning Block
More informationSellotape Dispenser E112134#1
2. 4 Sellotape Dispenser Please Note The OPITEC range of projects is not primarily intended as toys for young children. It is for teaching, designing and making to ensure that pupils experience a range
More informationmarbles (16mm) marbles (25mm) meter stick 10 1 sorting circle 10 1 tape (only necessary if using string) 10 rolls 1 roll
Grade 5 Teachers Group of 3 Engage marbles (16mm) 90-130 9-13 marbles (25mm) 10-30 1-3 meter stick 10 1 sidewalk chalk (optional) 10 sticks 1 stick sorting circle 10 1 string (optional) 20 meter length
More informationThe Weight of Success: OT in the Classroom. Created by: Rebecca Ritter, OTS Milligan College Occupational Therapy Program
1 The Weight of Success: OT in the Classroom Created by: Rebecca Ritter, OTS Milligan College Occupational Therapy Program 2 Table of Contents Purpose... 3 Activities..4 Loops Lap Pad..5 Felt Letter Puzzles
More informationEcole BEAU MEADOW School
GRADE ONE STUDENTS SUPPLIES FRENCH IMMERSION 4 ½ plain ½ INTERLINED project books --------- ( PLEASE DO NOT SEND ½ PLAIN, ½ RULED) 6 Duo-tangs (1 each Red, Blue, Green, Yellow, Black, Orange) Large scrapbook
More informationWind Turbine Experimenter s Kit User Guide
Wind Turbine Experimenter s Kit User Guide 42284 V0116 Cautionary and Warning Statements This kit is designed and intended for educational purposes only. Use only under the direct supervision of an adult
More informationSlicing Jig For Pen Inlays
Slicing Jig For Pen Inlays By Randall Smith (randyrls) May 2008 This article has been downloaded from the library of the International Association of Penturners. www.penturners.org You are welcome to reproduce
More informationSpecifications Wingspan: 43cm Flying Weight: 33 grams (with battery) Channels: 3 Suggested Receiver: 4Ch Micro Motor: 7mm Brushed Geardrive
Specifications Wingspan: 43cm Flying Weight: 33 grams (with battery) Channels: 3 Suggested Receiver: 4Ch Micro Motor: 7mm Brushed Geardrive Airframe Kit (Included Contents) * Airframe Parts Sheets (Depron)
More informationAfter printing these plans, several pages will need to be taped together to form a larger plan. Below is a diagram of which pages need assembled.
Watermill Building Plans For complete building instructions and instructional videos, please visit the main web site at www.hirstarts.com/watermill/watermill.html. Using these plans alone will not give
More informationAdjustable Box Joint Jig. Richard Hicks on 8/24/2015. Box or Finger Joints
Adjustable Box Joint Jig Richard Hicks on 8/24/2015 Box or Finger Joints Adjustable Box Joint Jig Richard Hicks on 8/24/2015 Box Joints are also called Finger Joints Because they have interlocking fingers
More informationFOX VALLEY CHRISTIAN ACADEMY SUPPLY LIST
FOX VALLEY CHRISTIAN ACADEMY 2017-2018 SUPPLY LIST PRESCHOOL LARGE ZIPPERED backpack (labeled with name) 1 pkg. Crayola WASHABLE BROAD TIP markers (8 count, classic colors) 1 pkg. Crayola WASHABLE FINE
More informationJAGUAR XKR : Assembly Instructions
View of compleate model(side view) View of compleate model(front view) JAGUAR XKR The Jaguar XKR brings the Jaguar Sports Car tradition that began with the XK 120, into the modern era. The sleek curves
More informationSky Eagle. User Guide. Cautionary and Warning Statements
Sky Eagle User Guide 60089 V0613 Cautionary and Warning Statements This kit is designed and intended for educational purposes only. Use only under the direct supervision of an adult who has read and understood
More informationEngineering Directive
Thing-a-ma-Jig Finishing To Finish a model means to apply paint and other decorations to complete the look of your model. Meaning to apply a finish. That is what we will discuss in this section. Applying
More informationSingle MJ Splitter Installation Manual - 1Si
SP1 Single MJ Splitter Installation Manual - 1Si Micro Jig, Inc. PO Box 195607 Winter Springs, FL 32719, USA. Tel: 1-407-696-6695 Web site: www.microjig.com Email: sales@microjig.com Copyright 2004 Micro
More informationFOX VALLEY CHRISTIAN ACADEMY SUPPLY LIST
FOX VALLEY CHRISTIAN ACADEMY 2018-2019 SUPPLY LIST PRESCHOOL LARGE ZIPPERED backpack (labeled with name) 1 pkg. Crayola WASHABLE BROAD TIP markers (8 count, classic colors) 1 pkg. Crayola WASHABLE FINE
More informationSilverware Chest Plan
Silverware Chest Plan 05L14.01 Introduction 1. Measure the space required for your cutlery before beginning this project to be sure that it will fit in the drawers and top compartment. The best way to
More informationPlastic Supply Box (snap lid) 1. Large Erasers 2. Jumbo Glue Sticks 2. Blunt Tip 5" Kid's Scissors 1. Crayola brand BIG Crayons
Plastic Supply Box (snap lid) 1 Large Erasers 2 Jumbo Glue Sticks 2 Blunt Tip 5" Kid's Scissors 1 Crayola brand BIG Crayons Plastic pocket folders 2 Large pack of baby wipes Paper Towel Roll Pillow, blanket
More informationSupply List for Pre-Kindergarten
2017-18 Supply List for Pre-Kindergarten 4-12 count boxes of Crayola jumbo crayons Crayola brand only 1-10 count washable Crayola thick classic markers Crayola brand only 2-8 count of watercolors 1-12
More informationThe following is the process of preparing the making the wedge ornament
Wedge Christmas Ornament The following is the process of preparing the making the wedge ornament Setting up your saw to cut true 11.25 degree angles for a 16 piece to make a circle that will form the globe
More informationThe Park Hotel Instructions for Assembly of N Scale Kit
The Park Hotel Instructions for Assembly of N Scale Kit Kit Contents: 198 ea. Laser Cut Acrylic Parts, 2 ea. Chimney Parts Sheets, 1 ea.2".040 styrene rod, 5 ea. Sidewalk Parts, 14 ea. Cast Resin Dormers,
More informationBig Oz. Rocket. User Guide V0313
Big Oz Rocket User Guide 59824 V0313 Materials Included The Big Oz Rocket Kit should include the following materials. If something is missing, contact Customer Service at 800-358-4983. 20-ounce plastic
More informationKindergarten Supply List
Kindergarten throughout school year especially pencils, crayons, and glue sticks. Please label all personal items and all 4 - #2 pencils with erasers (sharpened) 1 - box of regular sized crayons (no more
More informationHoly Redeemer Fundraiser! Order Your School Supplies
Holy Redeemer Fundraiser! Order Your 2017-18 School Supplies You can now start ordering supplies from Sprout for the 2017-18 school year! HR is partnering with a new school supply provider this year that
More informationInvisible Clip Tutorial
Invisible Clip Tutorial I first saw what I call the Invisible Clip in Russ Fairfield s PMG gallery and fell in love with it. I could not figure out how he made them so I sent him an e-mail and he was kind
More informationA Day House. A View of One Way to Finish the Exterior of The Day House. Read these instructions all the way through before beginning this project.
A Day House A View of One Way to Finish the Exterior of The Day House Read these instructions all the way through before beginning this project. General Comments For the purposes of this project, the standard
More informationCardboard Model Buildings
Cardboard Model Buildings Get more model kits from http://www.modelbuildings.org PRINTING & ASSEMBLY TIPS: These OO designs can easily be resized by reducing the print percentage as follows: OO scale is
More informationNoville School Diorama Part 4 Making the Floors and Plastering the Walls and Ceilings
Noville School Diorama Part 4 Making the Floors and Plastering the Walls and Ceilings Moulds and Materials Making the Floors Plastering the Ceiling Plastering the Walls Installing the Ceiling and Floor
More informationApplying Fret Space Numbers and/or the Label Set to a Fretted Fingerboard
Jixis TM Graphical Music Systems Applying Fret Space Numbers and/or the Label Set to a Fretted Fingerboard The Jixis system was designed so that you would not need to apply the Jixis labels directly to
More informationNote. One - point Advice. To begin. Basic working method and markings. Fold along these lines. The printed surface should be
Note To begin Basic working method and markings Tools and materials needed -Ruler - scissors - blade cutter or "Exacto-knife" - awl or other pointed tool (for making a folding crease) - felt pen - pin
More informationStudent Stationery Pack Academic Year
Student Stationery Pack -2017-2018 Academic Year KG1 For 3 Terms White Board Markers 16 Chunky Triangular Pencils 12 Regular HB Pencils 20 Flexible White Board 1 Triangular Pencil grip 1 Chunky Colouring
More information15 Dovetail Jig. Instruction Manual. Part # 3452
15 Dovetail Jig Instruction Manual Part # 3452 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools. Peachtree Woodworking
More informationSt. Michael School Supply List School Year 1st Grade 1B and 1G
1st Grade 1B and 1G 3 ea 2 Pocket Folders Pockets Only (1 for Music) (no plastic) - **do not mark with subject 1 ea 2 Pocket Folder for Spanish (Blue) (no plastic) - **do not mark with subject 3 ea 2 Pocket
More informationJAGUAR XKR : Assembly Instructions
JAGUAR XKR : Assembly Instructions View of compleate model(side view) View of compleate model(front view) JAGUAR XKR The Jaguar XKR brings the Jaguar Sports Car tradition that began with the XK 120, into
More informationThe Astronomical League
The Astronomical League www.astroleague.org Library Telescope Modifications Check the collimation with the eyepiece cap provided (the one with the hole in its center) before starting on any modifications.
More informationELMER S. GISH SCHOOL Supply List. GRADE THREE Please no liquid paper. Please submit $8.00 in a labeled envelope to
Global GRADE ONE Unlabeled: We will group these supplies and share them. Do not label them. 3 Boxes of tissues (150-200 per box) 4 Dry erase markers 2 containers disinfectant wipes 1 Box large zip lock
More informationBuilding Instructions
Building Instructions Tools Required Tape measure Straight edge Pencil/pen Jigsaw Table Saw Circular Saw Electric drill 1 Hole saw bit Saw horses/table Protractor Staple gun Caulk gun Paint brush Wrenches
More informationThreads n Scissors. Easy Flip Flops
Easy Flip Flops Method Hoop 2 layers of water soluble stabilizer. Cut a piece of 1 mm thick 3D foam to fit the inside of the hoop. Put the foam onto the stabilizer and stitch out the design. Materials
More informationWRIGHT FLYER 1 INSTRUCTIONS FOR THE D10LC KIT
WRIGHT FLYER 1 INSTRUCTIONS FOR THE D10LC KIT Manufactured in the USA by Easy Built Models PO Box 681744, Prattville, AL 36068-1744 Visit us at www.easybuiltmodels.com Easy Built Models GLUE METHODS Always
More informationEcole BEAU MEADOW School
GRADE ONE STUDENTS SUPPLIES FRENCH IMMERSION 2 ½ plain ½ INTERLINED project books --------- ( PLEASE DO NOT SEND ½ PLAIN, ½ RULED) 2 Complete page INTERLINED scribbler 5 Duo-tangs (1 each Red, Blue, Green,
More informationAssembly Instructions to make the box organiser for the board game Perditions Mouth
Assembly Instructions to make the box organiser for the board game Perditions Mouth With a craft knife and sandpaper, remove the pieces from the sheets of plywood as you do each tray. The pieces are almost
More informationSCULL HANDLES AND GRIPS INSTRUCTION BOOKLET
SCULL HANDLES AND GRIPS INSTRUCTION BOOKLET Contents Section I: Scull Grip Replacement: Fixed Handle or 10 cm Length Adjustment System Refer to this section if you need to replace the grips on your fixed
More informationTrumpet : Assembly Instructions
A trumpet is a brass instrument which is played by blowing air into the mouthpiece and causing vibrations with the lips, while operating piston or rotary valves. A trumpet's shape and the length of its
More informationSupply List
2017-2018 Supply List Please note that there may be items not on this list that teachers notify students about after school begins but this is designed to be a fairly comprehensive list of what is needed
More informationHOW TO MAKE A R2D2 PENCIL HOLDER
HOW TO MAKE A R2D2 PENCIL HOLDER By Kaicie Messer 1 Introduction This set of instructions explains how to make a R2D2 pencil holder. It will not detail other characters. Any person of any age and skill
More informationSOUTH PARK FAMILY SCHOOL
GRADE: Kindergarten 1 Erasers NOT Labelled 4 Glue sticks large 40 g NOT Labelled 8 12 Thick felt pens (washable) NOT Labelled 12 24 Crayons NOT Labelled 2 Blank exercise books NOT Labelled 2 Duo tangs
More informationThis book, or portions of it, may not be duplicated, resold, or redistributed in any way, without the expressed written consent of Stay Tooned, Inc.
Copyright 2006 - Stay Tooned, Inc. All rights reserved worldwide. This book, or portions of it, may not be duplicated, resold, or redistributed in any way, without the expressed written consent of Stay
More informationStudent Purchase List
2. #2 pencils: 24-count (preferred brand Ticonderoga) 4. 2 boxes of crayons: 24-count (preferred brand Crayola) 5. 1 set of extra undergarments (sealed and labeled by name in a ziplock bag) 6. Water bottle
More informationHOW TO MAKE A HARLEY QUINN HAMMER
4D MODELSHOP MODEL MAKING GUIDE HOW TO MAKE A HARLEY QUINN HAMMER This guide shows you how to cut, shape and stick Styrofoam and Plastazote. A video of this build is available on our website. If you make
More informationCollapsible Book Cradle These instruction copyright Tara O Brien, 2014
Collapsible Book Cradle These instruction copyright Tara O Brien, 2014 Materials: book board covering material - we ve used tyvek and buckram pva 3BT (Board Thickness) jig the height of the cradle book
More informationSchool Supply Lists
2017-2018 School Supply Lists Kindergarten (2 Day & 3 Day Classes) 1 plastic pencil box 5 x 8 2 plastic folder with pockets and brads: 1 red, 1 green 1 RED plastic folder with pockets (no brads) 2 composition
More informationEPP Rebel Z 35. White Red w/ Blue Orange w/ Blue Orange w/burgundy Other. Specs. Color - Bottom White Black Checkers Silver Checkers Other Checkers
EPP Rebel Z 35 Specs AUW ~10.0oz Width 35.28 Length 34.67 Wing Area 1.44 sqft Horz Area 2.35 sqft Vert Area.91 sqft
More informationOption 1: False Frame Bent
Black Bear Construction Co. www.blackbearcc.com Standard and Narrow Gauge railroads are often used in industrial or short line operations. These areas often require drainage that can be provided by trestles.
More informationInstructions for Turning Laminated Bracelets
Instructions for Turning Laminated Bracelets 1. Start with Design 1. Make a paper template circle for the bracelet. Use this to check the fit on the person you are making the bracelet for. After checking
More informationSCHOOL SUPPLIES St. Joan of Arc School
Kindergarten number. (Lunch box, clothing, gym clothes, school bags, school supplies, etc.) 1-2 pocket folder with name on upper right corner Markers (Washable, 10 pack primary colors) Print name on each
More informationPinwheel. Method. Materials
Pinwheel Square sheet of construction paper. Marker or pencil Scissors Tape or staple Thumbtack Pencil with an eraser on the end Start with a square piece of construction. Draw an X, from corner to corner.
More informationHalloween Countdown Mansion. 64 Designs. INCLUDES 43 DESIGNS FOR 4" x 4" HOOPS, 21 DESIGNS FOR 5" x 7" HOOPS. In-the-Hoop!
constructed in sections in-the-hoop on cut-away mesh stabilizer. structed individually in-the-hoop, this easy Project Halloween Countdown Mansion Create the Halloween season s must-have interactive countdown
More informationESSENTIAL TOOLS NEEDED FOR EVERY QUILTER
You ll thank me later If you are a beginner to quilting, the tools you need are few. There are, literally, thousands of tools for quilting available to the stitcher..it can be very confusing. So, to simplify,
More informationChapter Four, Fitting out the Shell
Chapter Four Fitting out the Shell This chapter outlines the process for fitting the parts that go into a round or stave back shell. Square back sound boxes usually have the cap and base of the sound box
More informationKINDERGARTEN (ENGLISH AND FRENCH) 2018 / 2019 STUDENT SCHOOL SUPPLY LIST
KINDERGARTEN (ENGLISH AND FRENCH) 4 large Elmers or Lepage glue sticks (with snap on, NOT screw on caps) 1 package of 10 Crayola broad markers (original colours, unscented) 4 blank, unlined Hilroy exercise
More informationPaper Toys The Easter Story Assembly Instructions
BIBLE Paper Toys The Easter Story Assembly Instructions TOOLS NEEDED Assembly Instructions Sharp scissors. Paper-cutting knife (recommended: X-Acto knife with a #11 blade). Sturdy tweezers with smooth
More informationFidelity & Guaranty Building
Fidelity & Guaranty Building Instructions for Assembly of the Fidelity & Guaranty Building Kit Contents: 69 each laser cut acrylic parts. 1 each sheet of AC roof unit parts. 1 each sidewalk base. 4 each
More informationStationery List for the School Year
Stationery List for the School Year 2016-2017 In order for you to catch the stationery sales during the summer, we are printing the items that may be purchased outside of school. Please do not purchase
More informationALIEN ENCLOSURES GM A-BODY Trunk Panel Kit instructions
ALIEN ENCLOSURES 68-72 GM A-BODY Trunk Panel Kit instructions TYPICAL TOOLS & MATERIALS NEEDED FOR UPHOLSTERED KITS 2 Yards of Main Panel Material 1.5 Yards of Backer Material 3 yards of foam backing material
More informationJimmy s 2 nd demonstration was what he called an African Drum style box made from Iroko with a cocobolo insert in the lid with inlaid sterling silver.
Jimmy s 2 nd demonstration was what he called an African Drum style box made from Iroko with a cocobolo insert in the lid with inlaid sterling silver. He started by roughing out the block with a roughing
More informationA Slim,Comfortable. In 1979 I spent five months designing. This system works for most chairs and uses common materials
A Slim,Comfortable This system works for most chairs and uses common materials An upholstered slip seat complements a beautiful chair. Using modern materials, it s not difficult to construct an elegant
More informationShell Gas Station & Convenience Store kit in HO scale
Shell Gas Station & Convenience Store kit in HO scale Parking lot base and cars not included This kit includes all building parts and signs milled in white and black styrene plastic, clear window glazing,
More informationCVS Pharmacy kit in HO scale
CVS Pharmacy kit in HO scale Parking lot base and cars not included This kit includes all building parts and wall-mounted signs milled in white styrene plastic, clear window glazing and pre-cut Plastruct
More information3Position the hull of the ship as
Yamato: Step-by-step 25 The hull and stern deck c b d a b d c e e f a Rear frame b Stern deck x 2 c Stern deck x 2 d Side wall x 2 Wood glue Sandpaper (no. 400 grain) Craft knife Pliers d Side wall x 2
More informationA Precision 2000 Mixed Media Project
Día de los Muertos (Day of the Dead) Panel A Precision 2000 Mixed Media Project PROJECT TITLE: Día de los Muertos (Day of the Dead) Panel DESIGNED BY: Andy Spencer SKILL LEVEL: (Adult 1-5: 1 being the
More informationInstructables Butcher Block Top
Instructables Butcher Block Top Project Overview: This project requires basic woodworking skills and access to woodworking machines. Woodworking machines have sharp cutting edges and are NOT forgiving.
More informationTaco Bell Restaurant kit in HO scale
Taco Bell Restaurant kit in HO scale Parking lot base and cars not included This kit includes all building parts milled in white styrene plastic, clear window glazing, Plastruct tile roofing, and logo
More information