ALIEN ENCLOSURES CAMARO AND FIREBIRD Trunk Panel Kit Instructions
|
|
- Franklin Bates
- 5 years ago
- Views:
Transcription
1 ALIEN ENCLOSURES CAMARO AND FIREBIRD Trunk Panel Kit Instructions TYPICAL TOOLS & MATERIALS NEEDED FOR UPHOLSTERY 2 Yards of Main Panel Material 1.5 Yards of Backer Material 3 yards of foam backing material (Optional) headliner material suggested 2 Yards of automotive carpet Tools need would include: Razors, Sandpaper, #2 Phillips screwdriver, Heat Gun/Hair Dryer, Spray Adhesive, Staple Gun LIGHT KITS WILL REQUIRE: 1 Piece of 1/2 finish grade plywood. Final piece will be 56 1/2 x 14 1/4. Approx. (30) 7-7/16 backing panel framing screws (For attaching inserts, and / or backing panels with associated kit. Approx. (30) 1 Fine Thread Drywall screws (for attaching braces and mounting blocks). Approx. 8.5 ft. of Hook & Loop strips enough for (15) 6 strips and (1) 12 strip (B&C).
2 Congratulations and thank you for the purchase of your new Camaro / Firebird custom trunk panel kit! As you can see there are multiple pieces to your kit. You will want to verify that no pieces are missing and none of them are damaged. Please let us know if there are any discrepancies. Also, you will notice there are holes on each panel without obvious purpose. These are necessary screw wholes required during the CNC process to secure panels to the cutting bed. They are placed where they will not interfere with the assembly or the finished product. Finally take care removing items from the package and handling the. We try to lightly sand the edges of all pieces; however you may still be susceptible to splinters if you run your hand or fingers along the edges. A more detailed sanding may be preferred. UPHOLSTERED & UN-UPHOLSTERED KITS - INCLUDED MATERIALS: (SOME QUANTITIES AND ITEMS MAY DIF- FER DEPENDING ON DESIGN) 1) One Front Design Panel (towards front of vehicle) Marked A 2) Two Rear Panels (Rear of vehicle) Marked B & C 3) Two Side Panels Marked D & E 4) One Floor Panel Marked Floor 5) Six 6 X 1 Square braces for the ends of the floor Panel, Panel A & Panel B 6) One 12 X 1 Angled brace for the center of the C Panel, (Handle C Panel with care until 12 brace is attached) 7) Ten 6 X 1 Angled braces. Two for the C Panel, Eight for the floor Panel 8) One Package of 1 Fine Thread Drywall screws (for attaching braces) UN-UPHOLSTERED KITS - INCLUDED MATERIALS: (SOME QUANTITIES AND ITEMS MAY DIFFER DEPENDING ON DESIGN 1) Backing Panels / Inserts with letters the same as their coordinating panels (i.e. A-BP = Panel Backing Panel, AN = Panel A Insert) (Quantity may differ by design) 2) One Package of (30) 7-7/16 backing panel framing screws (For attaching inserts, and / or backing panels with as sociated kits 3) 9 ft. of Hook & Loop strips enough for (15) 6 strips and (1) 12 strip (B&C). (Panels can also be permanently attached) UN-UPHOLSTERED LIGHT KITS Light kits will include most of the previously mentioned items. Items not included are: 1) One Floor Panel Marked Floor 2) All mounting hardware * Instructions for Floor Fabrication are included in the next section with diagrams at the end of the instructions. *A-BODY IMAGES USED IN MOST OF THE INSTRUCTIONS - ASSEMBLY IS SIMILAR
3 LIGHT KIT FABRICATION: If you have purchased one our Light kits, you will need to fabricate the Floor panel. Please refer to last page of instructions for hole drilling diagram and brace layout. You will need to cut or have cut a piece of 1/2 finish ply plywood for the floor. The floor size is: 56-1/2 X 14-1/4 ASSEMBLY: Some kits will be partially assembled. You will need to complete the assembly of Panel A, B & Floor Panel Panel A has two 6 Square Braces. Use the 1 Fine Drywall screws for this installation. (Figure 1). Blocks will be mounted to the upholstered side of the panel, with the Velcro facing inward. Panel B has two 6 Square Braces. Use the 1 Fine Drywall screws for this installation. (Figure 2). Blocks will be mounted to the upholstered side of the panel, with the Velcro facing inward. (Figure 1) The Floor Panel has two 6 Square Braces. Use the 1 Fine Drywall screws for this installation. (Figure 3). The floor panel also has 4 angled block on each side. Blocks will be mounted to the carpeted side of the panel, with the Velcro facing inward.
4 ASSEMBLY: Some kits will be partially assembled. You will need to complete the assembly of Panel A, B & Floor Panel Un-upholstered kits Panels B&C can be permanently attached or left separate by using Velcro strips. Most kits will be partially assembled. Screws and Velcro is provided. (Figure 4). 67/68 Kits will require additional assembly of the fuel filler hump that is attached to the B Panel. See 67/68 Addendum for details TEST FIT / INSTALLATION SEQUENCE: You will quickly learn the sequence of the panel assembly. The first few times follow these easy steps: Place your floor panel in the trunk first. 67/68 models have a fuel filler recess that will need to be aligned with the fuel neck hump. (Figure 5) Second install the front panel (A). This may be the trickiest panel to install. You will want to center between the deck lid hinges with the TOP FIRST. The top edge goes just under the deck lid seal channel. (Figure 6) (Figure 5) (Figure 6)
5 The panel must be aligned on the left and right with the floor panel. (Figure 7) Next install the rear panels (B&C). These should already be attached. This panel installs easily from the rear of the vehicle by inserting one side first into side quarter panel cavity. Align with the floor panel on the ends (Figure 8) (Figure 7) (Figure 8) Finally install each of the side panels. These must be installed top rear first (thin pointed end of side panel). You may need to shift the floor and rear panels slightly to make each of the edges touch (they will touch with adjustment). (Figure 9) (Figure 9) *Un-upholstered Kits Once you have finished the test fit of the panels, you may need to trim some of the panels. This can be done with a sharp utility knife or power saw and/or sander. Trim as necessary. Remove bracing blocks before upholstery. Mark each of the blocks with identifying marks for proper re-attachment.
6 UPHOLSTERY: There are actually several different ways to upholster the panels. In the photos shown; the inserts (N) were left out and the backing panels (BP) were covered with an alternate fabric. You may prefer to cover the panel and backing panel together with a tight wrapped and glued style where the covering material is stretched and pressed into the recesses. Another method would be to cover the inserts with an alternate material or with the same material as the main panel to give it a tucked look. Depending on your chosen upholstery style, you will need to upholster backing panels. Evenly space over opening from behind and use the 7-7/16 framing screws to attach approx 6 apart from each other. We have also found the addition of a permanent glue, (like Gorilla Glue) works great! (Figure 10) (Figure 10) After all pieces are upholstered, affix hook & loop strips to the bracing blocks with both sides affixed (the opposite piece attached). This will align the opposite piece with the fixed piece. (Figure 11) Remove the panels slowly to keep second hook & loop piece attached. If it comes loose, you may need to measure and re-fix. We strongly suggest using staples to aid in the attachment of the hook & loop to each of the blocks and panels. (Figure 11 ) (Figure 11)
7 UPHOLSTERY TIPS: 1. Test fit your pieces first to check for trimming (DO NOT ADHERE HOOK & LOOP AT THIS TIME) 2. It may be necessary to place shims or rubber feet under floor braces to ensure a firm fit of panel A 3. If you are covering with a thick material, you may need to trim the bottoms of the panels check first 4. Remove attached support blocks before covering 5. Check the penetration of your staples on a test piece of material we suggest ¼ or shorter - preferably 5/32 (available online) 6. We might suggest using a professional strength hot-glue or wood glue when re-attaching bracing blocks. You may also want to consider staples as well. 7. We strongly suggest stapling the hook & loop in several spaces on each side of each tape to prevent the release of the tape 8. You may want to consider using smaller pieces of hook & loop on the side panels for easier release. These panels can be somewhat difficult to remove when completely adhered. 9. When removing side panels place one hand on the top of the panel and another at he bottom rock the panel bottom out first (reverse of install). You may want to use a paint key to grasp the bottom of the panel to pull outward. 10. We suggest using a foam backed vinyl (thin 1/4 or less). It tends to keep the vinyl tight and can hide imperfections. However, our first kit did not have it. If you decide not to use the foam, we suggest spraying your material with spray adhesive prior to stretching over panels to prevent sag 11. You may want to reinforce the backer panels to the main panels with hot glue in addition to the 7/16 screws with small beads approx 6 apart.
8 67-68 Fuel Hump Instructions: The 67 and 68 F-Bodies had the fuel filler in the rear tail panel vs. behind the license plate in 69. So in order to allow for that, you will find additional pieces to assemble and upholster. Below are the diagrams of how the three pieces of the hump are assembled. We recommend glue and staples, however drywall type screws can be used to assemble. This hump and the B panel will need to be upholstered first then assembled together by using drywall style screws from the back of the B panel. We strongly recommend a test fit with hardware prior to upholstering. Be sure to align B Panel with floor to confirm proper alignment before attaching hump, as the floor hump is not centered.
9 We are always looking to improve this product and instructions. Please let us know if you may have suggestions. We also would love to see photos of your installed upholstered kits! We can be reached at anytime with questions or concerns (photos) at: OR We hope you enjoy your new trunk kit Thanks! Keep an eye out for our new custom package tray kits
10
ALIEN ENCLOSURES GM A-BODY Trunk Panel Kit instructions
ALIEN ENCLOSURES 68-72 GM A-BODY Trunk Panel Kit instructions TYPICAL TOOLS & MATERIALS NEEDED FOR UPHOLSTERED KITS 2 Yards of Main Panel Material 1.5 Yards of Backer Material 3 yards of foam backing material
More informationInterior CHAPTER 21. Phantom Roadster Instruction Manual 273
CHAPTER 21 Interior When you get to this chapter you are now starting on the finish that will make your car one that will be complete your hard work. This chapter will cover the installation of the door
More information15 - Interior. Interior. February GGG Page 15-1
Interior February 2003 15-GGG Page 15-1 15 - Interior This Page Intentionally Left Blank Page 15-2 15-GGG February 2003 Contents 15.0 - Chapter Preface...15-4 15.0.1 - Parts List...15-4 15.0.2 - Tools
More informationWood Duck Nest Box Design & Assembly Directions
Wood Duck Nest Box Design & Assembly Directions Instructions, Illustrations & Photos Courtesy of MWDI and Scott Jasion, Harford County Chapter, Ducks Unlimited Side door opening design for easy mounting
More informationChapter 18. Interior Doors
Chapter 18. Interior Doors 18.1 SWINGING DOORS 18.2 SLIDING DOORS 18.3 BIFOLD DOORS Tools needed by volunteers: Hammer Nail apron Tape measure Square Pencil Tools and equipment needed: Extension cords
More informationProduct must be installed as shown using the screws and brackets provided. Use of incorrect hardware could result in damage to the product.
General Notes These installation instructions are intended to be comprehensive for a typical Keyeira/Presto configuration. Your configuration may differ. If you have questions contact Geiger Customer Service
More informationFrameless Inline Door With Return QCI5263
INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges
More information3Insert the second rod no. 4
Yamato: Step-by-step 37 The stern block and searchlight control towers a b c d e f Recommended tools and materials Wood glue Sandpaper (no. 800 grain) Metal file Putty Craft knife For metal: Super Glue
More informationSlide the stock rubber tank mount caps onto the ends of the CS-1 tank mount:
RYCA CS-1 BODY PARTS INSTALLATION GUIDE [The CS-1 installation guides should be used as supplements to the videos found on our Youtube Channel. There is no strict order to the build process, but it is
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS For Wallbed models: Do-It-Yourself BOOKLET #C90 WARNING! ALL MURPY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationWILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount
WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount For Wallbed models: Do-It-Yourself Insturction booklet C92 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE
More information3555 Scarlet Oak Blvd. St. Louis, MO FAX:
I. INSTALLATION TOOLS A. Utility Knife B. Scissors C. Sand Paper and/or File D. Fabric Tucking Tools (available from Fabric Wall) 1. Rocker Tool 2. Flat Blade with round edge 3. Bent Blade with round edge
More informationInstallation Instructions
Installation Instructions Targa Top Restoration Kit Porsche 911 1965-1992 About Us: ClassicCarCarpets develops, manufactures and markets premium quality carpet sets for classic cars. Our handcrafted carpet
More informationBuild your own Drawer unit. D3 / D4
Page1 Build your own Drawer unit. D3 / D4 1: Introduction. This guide will give you the plans, materials and how to information to build your own drawer unit. The dimensions given will fit a D3 or D4,
More informationTech Sheet. T4 Interior conversion kit how to - fitting instructions. 1. Rear seat belts. 2.
Page 1 of 8 T4 Interior conversion kit how to - fitting instructions Thank you for purchasing our T4 interior conversion kit. This kit will enable you to convert any SWB left hand loading door T4 into
More informationAll Terrain Flares 2014 Chevy Silverado
Page 1/8 Components: 1. Front Flares (2) 2. Rear Flares (2) Tools required: - Utility knife - #2 Phillips driver - Socket wrench - 13 mm Socket - 6 mm Allen Wrench - T-15 Torx bit - Trim Removal Tool -
More informationChapter 20. Exterior Finish Work
Chapter 20. Exterior Finish Work 20.1 INSTALLING STORM DOORS 20.2 INSTALLING TOE KICK BOARD 20.3 INSTALLING PORCH RAILS 20.4 INSTALLING HOUSE NUMBERS 20.5 INSTALLING MAILBOX 20.6 AIR SEALING EXTERIOR PENETRATIONS
More informationMaking Simple Bookbinding Equipment. A Lying Press. Making Simple Bookbinding Equipment. A Lying Press. Tony Firman
Making Simple Bookbinding Equipment Tony Firman 28 1 2 27 Notes Making Simple Bookbinding Equipment Tony Firman Tony Firman Bookbinding 26 3 Making Simple Bookbinding Equipment: 2012 Tony Firman Bookbinding
More information4. Partially open the operating panel and tilt the top toward the interior of the door (Figure 4). Lift the panel off the sill and set it aside.
Effective Date: 10/1/2017 Tools Needed Kit Contents Hardware Kit Safety Glasses Cordless drill Phillips screw bit Two-step drill bit (3/8-1/8 ) utility knife Interior Mullion Exterior Mullion Cover clamps
More informationInstalling your new Bevella Top. L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls)
Installing your new Bevella Top L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls) Bevella RTI Countertops are engineered and manufactured to the highest quality standards, built
More informationHAND TOOL NOTES For each tool picture and name, please write what it s used for. You will have a quiz on this.
HAND TOOL NOTES For each tool picture and name, please write what it s used for. You will have a quiz on this. Tool (Name & Nut drivers Speed Square Adjustable Bevel Square CONSTRUCTION TOOLS: Tool (Name
More informationCobra X Q Construction Tips Construction: Bel y pan
Cobra X Q Construction Tips : The white plastic in this kit is high impact styrene. It can be painted with most types of coatings if light coats are applied this is necessary due to the thickness of the
More informationFrameless Inline Door QCI5248
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5248 FRAMELESS PANEL / DOOR / PANEL QCI5248 REV. 0 Page 1 Certified 06/16/2016 Parts List with glass to glass hinges *Quantities may vary. **Support Bar
More informationTux chair & half. assembly instructions
Tux chair & half assembly instructions Smooth & Wrinkle-Free Fabric Covers: In addition to these printed instructions, you may want to watch our beauty tips videos on the customer service page of our website.
More informationSTACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS
STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS 1290363 Revision 1 12/16 Page 1 Weather Shield Mfg., Inc. NOTICE CAUTION! Failure to install and maintain our product according to these instructions
More information3. Be careful not to cut off all of the adjustment screws. It may be better to take a little off of each end rather than all off one side.
QUIET DOOR KITS Description Quiet Door Soundproofing Kits are specifically designed for all your door soundproofing needs. The Quiet Door Perimeter Seal and Quiet Door Sweep are engineered to create a
More informationFrameless Heavy Glass Door with Header
INSTALLATION INSTRUCTIONS Frameless Heavy Glass Door with Header QCI5243 QCI5243 REV. 0 Page 1 Certified 06/16/16 Frameless Heavy Glass Door with Pivot Hinges ITEM NUMBER DESCRIPTION QUANTITY 1 DOOR GLASS
More informationSTYLE BAR & TONNEAU COVER INSTALLATION
STYLE BAR & TONNEAU COVER INSTALLATION INSTALLATION MANUAL: 2005 to '09 Mustang P/N: 10-8002-C12071B Saleen Performance, Inc. 1225 East Maple Rd., MI 48083 800-888-8945 www.saleen.com 1 IF YOU ARE NOT
More informationVinyl Gazebo Instructions
P a g e 1 Vinyl Gazebo Instructions 10 Vinyl Gazebo Shown Thank you for the purchase of your New Gazebo. Depending on the size of your Gazebo, installation can usually be completed in 1 to 2 days. These
More informationVinyl Installation Guide and Tips
Vinyl Installation Guide and Tips Tools Needed: Squeegee; Grease Pencil (white or blue only!); 2" & 1/4" Masking Tape Prepare your surface and vinyl as outlined on back cover prior to employing this technique
More informationMudroom Unit. Page 1 of 25
Mudroom Unit www.andrewharriswoodwork.com Page 1 of 25 Introduction This plan makes a unit which is 66 ¾ inches tall, 39 ½ inches wide and 18 ½ inches deep. It was custom made for some friends to fit the
More informationRESolution V2 Manual
RESolution V2 Manual Note for the German Manual: Yellow Bottle thick CA Pink Bottle Med CA Blue tube 5 minute Epoxy Green tube 90 Minute Epoxy Construction of the Fuselage Step 1: Cover the plan with a
More information10 x 12 home air pro. VISIT LINK BELOW FOR INSTALL VIDEO
in-ground installation instructions & user guide 10 x 12 home air pro VISIT LINK BELOW FOR INSTALL VIDEO https://www.maxairtrampolines.com/pages/support-information-videos Page 2 TABLE OF CONTENTS Materials,
More information7 x 14 flybed tramp. VISIT LINK BELOW FOR INSTALL VIDEO
in-ground installation instructions & user guide 7 x 14 flybed tramp VISIT LINK BELOW FOR INSTALL VIDEO https://www.maxairtrampolines.com/pages/support-information-videos Page 2 TABLE OF CONTENTS Materials,
More informationCurium 19H Installation Instructions & Parts List
Curium 19H Installation Instructions & Parts List Illustration Curium 19H Right Hand Page 1 of 15 01/07/2016 Revision 2.1 IMPORTANT This shower screen / enclosure must be installed by suitably qualified
More information14 x 14 super quad. VISIT LINK BELOW FOR INSTALL VIDEO
in-ground installation instructions & user guide 14 x 14 super quad VISIT LINK BELOW FOR INSTALL VIDEO https://www.maxairtrampolines.com/pages/support-information-videos Page 2 TABLE OF CONTENTS Materials,
More informationFOLDING DOOR - FOR FACTORY ASSEMBLED JAMBS WITH APPLIED SILL
FOLDING DOOR - FOR FACTORY ASSEMBLED JAMBS WITH APPLIED SILL READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according to
More informationRay chair & half. assembly instructions
Ray chair & half assembly instructions Smooth & Wrinkle-Free Fabric Covers: In addition to these printed instructions, you may want to watch our beauty tips videos on the customer service page of our website.
More informationStream NXT - assembly instructions
Stream NXT - assembly instructions Recommended settings CG (measured from root leading edge): Speed/launch camber (+down, near the wing root): Cruise camber (+down, near the wing root): Thermal camber
More informationWater Rocket Launcher
Rocket Activity Water Rocket Launcher Objective Construct a launch platform for launching water rockets. National Science Content Standards Physical Science Position and motion of objects Motions and forces
More informationGeneral Features. Low Profile. The SMART BOXX stands only 1.5 off of the bed of your truck so cargo space is maximized
General Features Low Profile. The SMART BOXX stands only 1.5 off of the bed of your truck so cargo space is maximized Two Sizes Short Box :74 L X 47 W X 7 T and Long Box 92 L X 47 W X 7 T All Aluminium
More informationDouble Frameless Swing Door QCI5247
INSTALLATION INSTRUCTIONS Double Frameless Swing Door QCI5247 WALL MOUNT HINGES QCI5247 REV. 0 Page 1 Certified 06/16/2016 Parts List with wall mount hinges *Quantities may vary **Quantities double where
More informationCurium 19.4H Installation Instructions & Parts List
Curium 19.4H Installation Instructions & Parts List Illustration Curium 19.4H Right Hand Page 1 of 21 30/06/2016 Revision 1.0 IMPORTANT This shower screen / enclosure must be installed by suitably qualified
More information3/16 OR 1/4 FRAMELESS SWING DOOR WITH SINGLE INLINE PANEL OR TWO INLINE PANELS
/ OR / FRAMELESS SWING DOOR WITH SINGLE INLINE OR TWO INLINE S This instruction sheet applies to the following units with a magnetic handle. C7, C7, C79 This instruction sheet also applies to the following
More informationGallium 03 Installation Instructions & Parts List
Gallium 03 Installation Instructions & Parts List Illustration Gallium 03, H1 Handle Left Hand: Open Out 04/05/2016 Revision 1.1 Page 1 of 19 IMPORTANT This shower screen / enclosure must be installed
More information1Take the keel (3) and
1 The hull and the bridge 1Take the keel (3) and apply PVA wood glue in the second slot from the left: a toothpick may make it easier. Take care: the left end is the one that has a projection. THE HULL
More informationFrameless Inline Door QCI5254
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5254 FRAMELESS DOOR / PANEL QCI5254 REV. 0 Page 1 Cer fied 06/16/2016 Parts List with wall mount hinges *Quanes may vary QCI5254 REV. 0 Page 2 Cer fied
More informationTHE GREEN CLUB PROJECT
tennis ball end cap finishing tape THE GREEN CLUB PROJECT duct tape How to make the ultimate recycled juggling club at home. BY JONATHAN POPPELE 16 or 20 oz bottle club body hardwood dowel collar finishing
More information'Mutiny' Ozone Reactor Kit
'Mutiny' Ozone Reactor Kit Skill Level: Beginner Tools Required: Scissors or razor blade Other Materials: Teflon tape Time to Build: Approximately 1 hour not including drying time Version: 2012 spray nozzle
More informationI n s t a l l a t i o n I n s t r u c t i o n s
HInged PAtio Door Systems I n s t a l l a t i o n I n s t r u c t i o n s IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation.
More information176 S. New Holland Road Gordonville, PA Tel: Fax: Playhouse Loft
176 S. New Holland Road Gordonville, PA 17529 Tel: 717-768-0066 Fax: 717-768-8569 A S S E M B LY M A N U A L Playhouse Loft Playhouse Loft revised 9/6/05 Assembly Manual Dear Customer, Thank you for your
More informationRadon 07 Installation Instructions & Parts List
Radon 07 Installation Instructions & Parts List Illustration Radon 07, H1 Handle Right Hand: Open Out 14/06/2016 Revision 1.1 Page 1 of 21 IMPORTANT This shower screen / enclosure must be installed by
More informationBlock Frame Inovo Patio Door/Transom/Sidelite Field Mulling Instructions. simonton.com/installation. If mulling sidelites, skip to Step 5.
Effective Date: 10/1/17 Tools Needed Kit Contents Safety Glasses Cordless Drill Phillips Screw Bit Two-step Drill Bit (3/8-1/8 ) Utility Knife Interior Mullion Exterior Mullion Cover Hardware Kit Clamps
More informationFrameless Heavy Glass Door with Wall Mount Hinges
INSTALLATION INSTRUCTIONS Frameless Heavy Glass Door with Wall Mount Hinges QCI-5245 QCI5245 REV. 0 Page 1 Certified 06/16/16 Frameless Door with Wall Mount Hinges ITEM NUMBER DESCRIPTION QUANTITY 1 DOOR
More informationDayton Audio 10" Dual Passive 500 Watt Subwoofer Kit
Dayton Audio 10" Dual Passive 500 Watt Subwoofer Kit Thank you for purchasing the Dayton Audio 10" with Dual Passive Radiator 500 Watt Subwoofer Kit with Built-In DSP. This subwoofer kit was precision
More informationPROMASTER 136 WB LOW ROOF WALL LINERS INSTALLATION INSTRUCTIONS
PROMASTER 136 WB LOW ROOF WALL LINERS INSTALLATION INSTRUCTIONS NOTES: 1. Before commencing, remove all wall liners and D Rings already installed in the vehicle. 2. Consult layout PDF and compare vehicle
More informationLaney loveseat. assembly instructions
Laney loveseat assembly instructions Smooth & Wrinkle-Free Fabric Covers: In addition to these printed instructions, you may want to watch our beauty tips videos on the customer service page of our website.
More informationFrameless Inline Door QCI5250
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5250 FRAMELESS PANEL / DOOR / PANEL QCI0249 REV. 3 Page 1 Certified 10/12/12 Parts List with pivot hinges *Quantities may vary. QCI0249 REV. 3 Page 2
More informationKam Aero 43% Extra 300.
Stab Sheeting Kam Aero 43% Extra 300. Stabs / Elevator: Make your skins using the same method as you did for the fuselage foam parts. The stabs require 8 sheets (4 per stab) of 4 x 48 A grain sheeting.
More informationDubnium 11 Installation Instructions & Parts List
Dubnium 11 Installation Instructions & Parts List Illustration Dubnium, H1 Handle Right Hand: Open Out Page 1 of 25 IMPORTANT This shower screen / enclosure must be installed by suitably qualified individuals.
More informationInstallation for Full Size Polaris Ranger Crew Doors
Installation for Full Size Polaris Ranger Crew Doors Order of Installation: Heater Doors Wiper on to Windshield Windshield Top & Back Panel Note: Most of the steps in these instructions need to be repeated
More informationINSTALL INSTRUCTIONS
Jeep JK Rear Corner Skins Product : JK200,JK201,JK202,JK203 Applica on : 2007+ Jeep Wrangler JK ( 2 Door and 4 Door ) Page ( 1 of 6 ) I WARNING Read the instruc ons completely before beginning installa
More informationThe Festival Assembly Instructions
The Festival Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown CONTACT INFORMATION: HomePlace Structures 301 Commerce Drive New
More informationFrameless Door QCI5284
Frameless Door QCI5284 F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com INSTALLATION INSTRUCTIONS Frameless
More informationFENDER FLARE INSTALLATION
: 2011-2014 Ram 2500/3500 Fleetside 76.3 inch and 98.3 inch Bed. Tools Required 1. #2 Phillips Driver 2. Socket Wrench 3. 8mm Socket 4. 1/2 Wrench 5. Utility Knife 6. Awl or Similar Pointed Tool PRIOR
More informationChapter 22 - Cabinets & Vanities
Chapter 22 - Cabinets & Vanities Contents Chapter 22 - Cabinets & Vanities... 22-1 Timing & Prerequisites... 22-2 Cabinets... 22-3 Cabinet Layout... 22-3 Wall Cabinets... 22-4 Assemble the Wall Units...
More informationGrade 8 Enriched Math Catapult Project 2012 Step by Step Instructions to building a catapult
Grade 8 Enriched Math Catapult Project 2012 Step by Step Instructions to building a catapult Grade 8 Enriched Math Project INSTRUCTION SHEET FOR CATAPULT Procedures, materials and tools: below is a step-bystep
More informationLaney chair. assembly instructions
Laney chair assembly instructions Smooth & Wrinkle-Free Fabric Covers: In addition to these printed instructions, you may want to watch our beauty tips videos on the customer service page of our website.
More informationTux sofa. assembly instructions
Tux sofa assembly instructions Smooth & Wrinkle-Free Fabric Covers: In addition to these printed instructions, you may want to watch our beauty tips videos on the customer service page of our website.
More informationPatrol Box Plans by David J. Yarusso Troop 609
Patrol Box Plans by David J. Yarusso Troop 609 Materials List: 1. One 4 x8 sheet of ½ thick cabinet grade (birch or oak) or AC plywood. If using AC grade, use the A grade surface on the outside for a clean
More informationRFS Class II Rocket Assembly Instructions
RFS Class II Rocket Assembly Instructions Instructions by: Loc Precision Photos by: Great Lakes Space Port Sheboygan Education Foundation, Inc. Welcome and thank you for joining the Rockets for Schools
More informationFENDER FLARE INSTALLATION
: 2009 - UP Ram 1500 Fleetside. (Exclude R/T Models) Tools Required 1. #2 Phillips Driver 2. Socket Wrench 3. 8mm Socket 4. 1/2 Wrench 5. Utility Knife PRIOR TO INSTALLATION Hardware Kit Included 5/16
More informationA Slim,Comfortable. In 1979 I spent five months designing. This system works for most chairs and uses common materials
A Slim,Comfortable This system works for most chairs and uses common materials An upholstered slip seat complements a beautiful chair. Using modern materials, it s not difficult to construct an elegant
More informationZiroli D-17 Beech Staggerwing
Ziroli D-17 Beech Staggerwing Parts List Vacuform Parts: Miscellanous Pieces 1 Four Side Panels 1 3/16" Tube, 2" Long 2 Lower Dash - Back Dash 2 Felt, 12x24 3 Dash 3 Cordury 12x24 4 Dash Hood 4 Aluminum
More informationBMW Z3/M Roadster
Convertible Top Installation Guide 1996-2002 BMW Z3/M Roadster What s Included A new convertible top includes sewn-in plastic retainers and tinted plastic window. Also, we enclose new BMW original metal
More informationINSTALLATION GUIDE. TRANZFORM Sound TRANZFORM Space
INSTALLATION GUIDE TRANZFORM Sound TRANZFORM Space Cornell Iron Works, Inc. 100 Elmwood Ave. Crestwood Industrial Park Mountain Top, PA 18707 Phone: 800.233.8366 or 570.474.6773 Fax: 800.526.0841 INSTALLATION
More informationPRO CYCTM PRO CYC, INC. SYSTEM 1.5 FS
ASSEMBLY INSTRUCTIONS Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship your cyc, so please take
More informationPITTS S2S CONSTRUCTION
PITTS S2S CONSTRUCTION FUSELAGE CONSTRUCTION 1) Place the right fuselage side over the plan and mark the former positions. Place the left side over the right side and mark the former positions. Glue F1
More informationINSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD
For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD INSTRUCTION BOOKLET #34 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationInstallation instructions. Targa Top Restoration Kit Porsche
Installation instructions Targa Top Restoration Kit Porsche 911 1965-1993 Before you begin: Installation of your Targa top takes 6 to 8 hours. You may want to print of these installation instructions or
More informationBen Franklin 5&10 Store
Ben Franklin 5&10 Store RIVER LEAF MODELS, LLC RIVER LEAF MODELS, LLC Thank you for purchasing the Ben Franklin 5&10 structure kit. Your kit includes everything you need to assemble the final product.
More informationFRAMELESS DOOR / PANEL WITH WALL MOUNT HINGES QCI5274
FRAMELESS DOOR / PANEL WITH WALL MOUNT HINGES QCI5274 QCI0274 QCI5274 REV. Rev. 1 0 Page Page 1 1 Date Certified: Certified 06/16/2016 10/01/10 Parts List with wall mount hinges ITEM NO. Part # DESCRIPTION
More information#P571 - Victorian Queen Fretwork Clock inspired by 18th century Victorian elegance. 17 H x 21 W. Requires a 3 1/2 clock insert.
- Victorian Queen Fretwork Clock inspired by 8th century Victorian elegance. 7 H x 2 W. Requires a 3 /2 clock insert. Cut on dashed line for Back Cut on solid line for Frame only. Stock: /8 - /4, cut each
More informationHatch Installation For Pygmy Solo and Double Kayaks
Introduction/Overview Hatch Installation For Pygmy Solo and Double Kayaks The hatch kit consists of several wooden lips, strapping and hardware. The hatch is constructed by cutting a hole in your deck,
More informationFUSELAGE CONSTRUCTION
FUSELAGE CONSTRUCTION Note: prior to building and gluing on the work surface use protective covering on your building surface. (wax paper or clear wrap) Fit the laser cut Fuselage Front and Fuselage Rear
More information176 S. New Holland Road Gordonville, PA Tel: Fax: Castle Loft
176 S. New Holland Road Gordonville, PA 17529 Tel: 717-768-0066 Fax: 717-768-8569 A S S E M B LY M A N U A L Castle Loft Castle Loft Assembly Manual revised 08/31/05 Dear Customer, Thank you for your purchase
More informationHONDA RIDGELINE (KIT #601) Installation Instructions (to be used in addition to owners manual)
HONDA RIDGELINE (KIT #601) Installation Instructions (to be used in addition to owners manual) IMPORTANT NOTE: Read before beginning installation. These instructions replace all of Step 1 of the instructions
More information4-Door Rear XHD Armor Fenders
Page 1/10 Part #11615.02 Page 2/10 1 4 2 3 5 Components 1. Left Rear Fender (1) 2. Right Rear Fender (1) 3. Left Rear Guard (1) 4. Right Rear Guard (1) 5. License Plate Bracket (1) OMIX-ADA TECHNICAL SUPPORT
More informationC-180 Builder s Manual
C-180 Builder s Manual. May 20, 2002 Last revised July 11, 2002 Copyright! 2002 Douglas Binder, Mountain Models www.mountainmodels.com sales@mountainmodels.com (719) 630-3186 1 Required Equipment! Xacto
More informationINSTALLATION GUIDE PREMIUM FRONT BUMPER. AEV30103AE Last Updated: 09/08/14 US PATENTS: D683281, D CHINESE PATENT: ZL
PREMIUM FRONT BUMPER US PATENTS: D683281, D697842 CHINESE PATENT: ZL 2012 3 0026081.4 AEV30103AE Last Updated: 09/08/14 INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION,
More informationPrinting and Assembly of Kwawu Arm
Printing and Assembly of Kwawu Arm Jacquin Buchanan December 2016 This work is licensed under the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License. To view a copy of this
More informationTreviso POCKET BILLIARD TABLE INSTALLATION MANUAL. SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104
Treviso TM POCKET BILLIARD TABLE INSTALLATION MANUAL www.brunswickbilliards.com SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104 51-905881-000 NOVEMBER 2008 NOTE: Please use the instructions in this manual
More informationXenon 05 Installation Instructions & Parts List
Xenon 05 Installation Instructions & Parts List Illustration Xenon 05, H1 Handle Left Hand: Open Out 26/05/2016 Revision 2.1 Page 1 of 19 IMPORTANT This shower screen / enclosure must be installed by suitably
More informationPocket Door Kit PD1 / PD2 Installation Instructions. Kit Contents.
Pocket Door Kit PD1 / PD2 Installation Instructions Kit Contents. 1, Create Rough Opening In Stud Wall Construct rough opening ensuring all sides are square and level. Rough opening should be; Height =
More informationFord F150 Rear Flares Set Part # Revision
Ford F150 Rear Flares Set Part # 20074 Revision 1 04-01-09 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided.
More informationSliding Glass Door Assembly and Installation Guide
Sliding Glass Door Assembly and Installation Guide Index Door System Components and Hardware The following components are needed to complete the installation of your Sliding Patio Door unit. Check all
More informationTOOLS REQUIRED: HARDWARE INCLUDED: 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS
1 TOOLS REQUIRED: RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RUBBER MALLET FOR INSERTING PANELS 8MM HEX BIT WITH EXTENSION FOR HEX BOLT
More informationArmless. looseback sofa. assembly instructions
Armless looseback sofa assembly instructions Smooth & Wrinkle-Free Fabric Covers: In addition to these printed instructions, you may want to watch our beauty tips videos on the customer service page of
More informationPORTA TRAK OWNERS MANUAL
PORTA TRAK OWNERS MANUAL Table of Contents: I. Rail and Frame Parts List Please read the instructions thoroughly before setting up the Porta Trak. Carefully follow how to spring the bed step by step. II.
More informationAustralian Vintage Radio Society Inc.
Australian Vintage Radio Society Inc. (Incorporated in Victoria A0050003S) P.O. Box 3099, Syndal L.P.O., Victoria, 3150, Australia. Cabinet assembly instructions for the AVRS 10 th Anniversary construction
More information