FLEXITEEK INSTALLATION INSTRUCTIONS
|
|
- Maud Wilson
- 5 years ago
- Views:
Transcription
1 an Advanced Plastic Fabrications Company 99 marcus Blvd., fax FLEXITEEK INSTALLATION INSTRUCTIONS Before you begin, take your new Flexiteek deck out of the shipping package and lay it out flat in indirect sunlight for at least 60 minutes to allow the deck to relax and flatten out. In extreme temperature variances between the warm weather in South Florida, and the colder weather North of us the panel may shrink a little, placing panel in the warmth of the sun will allow the panel to return to it s proper size. Installation of your deck should not be done in the heat of the day. The ideal time would be in the morning or late afternoon, or under cover. Excessive heat will dry the glue out to quickly, not giving you time to position panels properly. 1
2 Installation of your deck should not be done in the heat of the day. The ideal time would be in the morning or late afternoon, or under cover. Excessive heat will dry the glue out to quickly, not giving you time to position panels properly. Remove all deck fittings if possible; this will give you an unobstructed work area. All surfaces must sound, smooth, and dry. All uneven areas and holes should be faired with suitable filler. Sand smooth any excess filler, loose paint or uneven areas with 60 grit sandpaper. Uneven areas left on the deck could show though the finished Flexiteek deck leaving unsightly high and low spots in those areas. Use denatured alcohol to clean the boat surface and the back of the Flexiteek panel if not free from dirt or dust just prior to cleaning. 2
3 Lay down the Flexiteek section that you plan to glue down, dry fit all panels into position making sure the panel fits correctly. Using a pencil trace along the entire outside of the panel, remove the panel and you will be left with a pencil mark as shown in the picture around the perimeter of the area requiring glue. Flexiteek can be trimmed to fit using a sharp utility knife or sand paper. Plan your cut and take the time to be as precise as possible, sand cut edges with 60 grit sandpaper to match texture of the panel face. 3
4 When multiple panels will be glued down within the same area make sure that the caulk lines line up from one panel to the next before gluing. Matching the caulk lines will give your deck a very professional look. Sdfsdfsdfsdfsdfsdfas Place masking tape along the outside of the pencil line you have drawn, also place tape across any corners that have a radius. Pencil Line Radius 4
5 Once more fit the panel onto the masked area and trace out the corners that have a radius. Cut out the traced portion of the radius, this completes preparing this area for applying the adhesive. 5
6 After tracing out the radius s, remove panel and trim the excess tape off with your utility knife. This area is completely taped off, clean and ready for gluing. Here is another example of how to tape the area for gluing, bending the tape to match the radius. 6
7 Place panel over area to be glued and fit into position. Place a weight on the middle of the panel and flip over one end, apply glue with a 1/16 notched trowel. Apply only one or two tubes of glue at a time or the glue may dry before the panel is laid back down. Panel is now glued into position, the tape will catch any excess glue, this will make clean up much easier. It may be necessary to weigh down the edges of the panel if the glue is not holding them tight to the deck, 2x4 s, bottles of water, etc. work well. Leave overnight. 7
8 Let glue dry for several hours prior to removing tape, this will prevent glue from getting on other boat surfaces. Keep a trash bag handy to put all the used tape in as you work. Use a floor roller or something similar to roll out excess glue and any air bubbles between the panel and the boat deck. Trapped air could result in bubbles in the face of the panel. Do not walk or kneel on the deck after you have rolled it out, lay a board down to distribute your weight if you must be on the glued deck. Keep traffic off the deck for at least a full 24 hours. 8
9 Only simple tools are required to apply the adhesive, these are available at any hardware store, use only a 1/16 notched trowel, this is plenty of glue to hold down Flexiteek and aids in drying. Use denatured alcohol to clean boat surfaces while the glue is still wet. You may also use denatured alcohol to wipe up any glue that may have soiled the surface of the deck. Plain white paper towel works best, cloth can leave lint attached to the glued edges 9
10 of the panels. It may be easier and quicker to sand the glue off the deck surface with 60 grit paper after the glue has dried. 10
11 Wear disposable gloves and change often while gluing; this will help keep glue from being tracked by your hands on to other boat surfaces. It may be necessary to lightly sand the edges of the panels to remove any excess dry glue, use a small piece of 60 grit paper to do this. It is not necessary to caulk the edges of the panels. If you elect to do so you may use black or white polyurethane or silicone caulk. 11
12 After all panels have been installed and the glue has dried you may wish to lightly sand the face of the deck panels with 60 grit sandpaper to remove any soil or scuff marks left during installation. Your installation is now complete, we know you will enjoy Flexiteek deck for many years to come. Thank you for choosing Flexiteek Deck Systems. 12
Darin Pitts Phoenix Arcade: How To - Tron Control Panel Overlay October 31, 2011
Step 1: Flattening the Artwork Tron artwork purchased from Phoenix Arcade will be shipped rolled. At least one week prior to application the artwork should be laid out on a flat surface in order for the
More informationContents. pages 20-24: Installing Edge sinks into. custom laminate countertops page 8: Installing Edge sinks into postform laminate countertops
Contents pages 2-8: Installing Edge sinks into custom laminate countertops page 8: Installing Edge sinks into postform laminate countertops pages 9-14: Installing Acrylic sinks into custom laminate countertops
More informationBUILD THE. Soleil Royal. Pack 1. The flagship of King Louis XIV.
BUILD THE Soleil Royal The flagship of King Louis XIV www.model-space.com Pack 1 Stage 1 Assembly Guide Hull frame, false keel and first deck half A 4 2 5 1 6 7 1A Smooth the surfaces of all the pieces
More informationInsta-DE Series Soft- padded Dry- erase Whiteboard Projection Screen
Insta-DE Series Soft- padded Dry- erase Whiteboard Projection Screen User s Guide Product Features Ø Award winning and GREENGUARD certified VersaWhite material. Ø 1.1 gain with 180 degree wide viewing
More informationInstallation Instructions for easy to install Texture Plus faux wall panels
Installation Instructions for easy to install Texture Plus faux wall panels Questions? Web chat, phone or email us. Easy Instructions For Use We make easy to install faux wall panels that look amazingly
More informationVERTICAL STILE ABOVE HORIZONTAL TRIM VERTICAL STILE BELOW COVE BASE ADHESIVE. 1" [25.4mm] BASE DETAIL
Please Read All sheet will be provided in stock sizes for field cutting. All trims will be provided in 8-0 stock lengths for field cutting. CEILING TRIM 1" [25.4mm] Acrovyn Interiors vinyl acrylic wall
More informationGet the benefits of oil with the ease of latex
One of the most rewarding home improvement projects is putting a fresh coat of paint on your kitchen cabinets. A new color brightens up your kitchen, and can give it a complete updated look. But at the
More informationNanton Grain Mill Assembly
( 1 ) Nanton Grain Mill Assembly Locate package for assembling storage building. These are cut from 1/8 masonite. Inspect and lightly sand edges where it will be bonded. Use white glue or CA glue to bond.
More informationInstallation Instructions
www.marlite.com Effective Date 03/01/2018 ARTIZAN FRP, SYMMETRIX FRP, ENVUE FRP, STANDARD FRP Installation Instructions Statements expressed in this technical bulletin are recommendations for the application
More informationHOW TO SELECT & USE A ROLLER
HOW TO SELECT & USE A ROLLER www.paintaids.co.nz 1 select the right roller The two most important things for a great paint finish are: a good quality paint, and the right roller sleeve to match the paint
More informationPROJECT PLANS WOODEN GIFT BOX
PROJECT PLANS WOODEN GIFT BOX Make the gifts you give even more special by presenting them in this one-of-a-kind gift box. In fact, the box may be valued more than whatever it contains. The box is sized
More informationSeamed Undermount Bowls
CUTOUT TEMPLATES MAKING CUTOUT TEMPLATES 7.1 CUTOUT TEMPLATES The use of an accurate template is one of the most essential elements to the successful completion of a cutout in Corian. For the completion
More informationWallgard 1,3 product
INSTALLATION INSTRUCTIONS Wallgard 1,3 product October 2015 GENERAL Application can be done to smooth, dry, clean, sound walls of concrete, plaster, hardboard, plywood and fibreboard. Board material must
More information675 Quick N Stall Neo Angle Framed Hinge Shower Enclosure
INSTALLATION INSTRUCTIONS 675 Quick N Stall Neo Angle Framed Hinge Shower Enclosure Call Technical Dept @ 1-800-452-2726 QCI1003 Page 1 of 9 Certified 10/01/09 INSTALLATION NOTES: Unpack your unit carefully
More informationSLAT/RUSH/CANE ROCKING CHAIR ASSEMBLY INSTRUCTIONS
SLAT/RUSH/CANE ROCKING CHAIR ASSEMBLY INSTRUCTIONS COMPLETE INSTRUCTIONS FOR THE FOLLOWING ROCKERS Ashton 700 Bradley 200/1200 Cross Creek 300 Collegiate 200SC Cumberland 250/1250 Highland Rim 7 Kensington
More informationBONDO PROCESS. Installation Guide.
BONDO PROCESS Installation Guide www.karran.com BONDO PROCESS This Installation Guide demonstrates simple methods and proven techniques for seamlessly installing Karran undermount sinks in laminate countertops.
More informationBLADE REPAIR INSTRUCTION BOOKLET
BLADE REPAIR INSTRUCTION BOOKLET Contents Section I: Section II: Section III: Section IV: Section V: Section VI: Removing a Blade Refer to this section if you need to remove the blade from an oar shaft.
More informationShutter Installation Instructions
Shutter Installation Instructions ITEMS YOU WILL NEED: Tape measure Framing square Screw gun Circular saw Caulk gun PL premium adhesive Exterior grade screws 1 ¾" Safety glasses Putty knife Window and
More informationStoring, Handling, and Cleaning dekō Markerboards Storing Markerboards. Handling. Cleaning
Storing, Handling, and Cleaning dekō Markerboards Storing Markerboards dekō markerboards must be stored inside, and stacked horizontally to avoid bowing. Do not store or transport dekō markerboards outdoors
More informationIncluded in Hardware Kit. Jeep Cut-Out Fender Flare Set of 4 Set Part # Rev STEP 1 PRIOR TO INSTALLATION
Jeep Cut-Out Fender Flare Set of 4 Set Part #10926-07 Rev-01 09-11-12 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware
More informationWallpaper. the Right Way. Wallpaper is trendy again, both with designers, who are speccing it more often, and
Wallpaper the Right Way Installed correctly, this wall covering should last a lifetime and come off easily once it has worn out its welcome By John Clift Wallpaper is trendy again, both with designers,
More informationChapter 5. Installation procedures. Installation procedures 24. Topics. Notes. 5.5 Flash coving General recommendations 25
Installation procedures 24 Chapter 5 Installation procedures Topics 5.1 General recommendations 25 5.2 Preparation 25 5.3 Seaming 25 5.5 Flash coving 26 5.6 Forming corners 26 5.7 Seam grooving 28 5.4
More informationRepairs. Chapter 10 Repairs 10. 1
10 Repairs Chapter 10 Repairs 10. 1 Repairs As an installer, you will probably be called upon to repair damage to a resilient floor. Here are some of the most common problems and the recommended repairs
More informationInstallation Instructions
Aspex Digitally Printed Wall Art PL PREMIUM HEAVY DUTY ADHESIVE ASPEX WALL ART DOUBLE SIDED FOAM TAPE Installation of Aspex Digitally Printed Wall Art with Foam Tape and PL Premium Adhesive. Maximum size
More informationSeascape Bungalow Assembly instructions. Laser Dollhouse Designs
Seascape Bungalow Assembly instructions Laser Dollhouse Designs NOTE: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also
More informationStep by Step Wing Bagging
Step by Step Wing Bagging By Evan Shaw 073 589 9339 evanevshaw@gmail.com Preparing the Leading Edge 1. Cut cores. (Cutting of wing cores is covered in another article elsewhere) 2. Sand the LE to a nice
More informationPRO CYC PRO CYC, INC. SYSTEM SUPER 1.5QS
Assembly Instructions System Super 1.5QS Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship your
More informationInstallation Instructions Palladium 3D Hi Impact Wall System, Partial Height with Color Matched Caulk Joints
Please read all instructions before installing Palladium 3D Hi Impact Wall System.. Before installation: a. Acclimate rigid sheet, Palladium 3D boards, adhesives and wall substrates to room temperature
More informationAll Terrain Flares 2014 Chevy Silverado
Page 1/8 Components: 1. Front Flares (2) 2. Rear Flares (2) Tools required: - Utility knife - #2 Phillips driver - Socket wrench - 13 mm Socket - 6 mm Allen Wrench - T-15 Torx bit - Trim Removal Tool -
More informationThe Lansdowne One Car Garage Assembly Instruction by Laser Dollhouse Designs
The Lansdowne One Car Garage Assembly Instruction by Laser Dollhouse Designs NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and
More informationHow to make a template to mount your plaque to a surface
How to make a template to mount your plaque to a surface A piece of heavy paper 3 4 wider than your plaque on all four sides (paper grocery bag works great too) Small amount of paint (latex dries the fastest)
More informationPRO CYCTM PRO CYC, INC. SYSTEM 1.5 FS
ASSEMBLY INSTRUCTIONS Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship your cyc, so please take
More informationINSTA-DE2 SCREEN SERIES
Section 1: Screen Design 1.1 What is it for? INSTA-DE2 SCREEN SERIES Convert entire walls into a dry-erase whiteboard projection screen: The Insta-DE 2 is a wall covering film material that instantly converts
More information1983 Jaguar XJS Interior Wood Trim Repair and Refinishing
The following describes and shows one method of wood trim repair/restoration/refinishing for wood trim on Jaguar cars, specifically this 1983 Jaguar XJS, although the wood trim should be the same in all
More informationLoose Lay Luxury Vinyl Plank
Loose Lay Luxury Vinyl Plank FLEX COLLECTION Installation & maintenance * PLEASE READ CAREFULLY * Installation, maintenance & warranty guideline for loose lay luxury vinyl products. Adherence to This guideline
More informationCraftman One Car Garage Assembly Instruction by Laser Dollhouse Designs
Craftman One Car Garage Assembly Instruction by Laser Dollhouse Designs NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit.
More information3Insert the second rod no. 4
Yamato: Step-by-step 37 The stern block and searchlight control towers a b c d e f Recommended tools and materials Wood glue Sandpaper (no. 800 grain) Metal file Putty Craft knife For metal: Super Glue
More informationTools and Tips: ( 1 )
Tools and Tips: As you build the book will show in my many picture manual how to assemble. You can use your own methods as you desire, but these worked best for me. A smooth, flat work surface is very
More informationThe Hamlin Assembly Instruction By Laser Dollhouse Designs
The Hamlin Assembly Instruction By Laser Dollhouse Designs NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also gives
More information176 S. New Holland Road Gordonville, PA Tel: Fax: Castle Loft
176 S. New Holland Road Gordonville, PA 17529 Tel: 717-768-0066 Fax: 717-768-8569 A S S E M B LY M A N U A L Castle Loft Castle Loft Assembly Manual revised 08/31/05 Dear Customer, Thank you for your purchase
More informationInstructions for Installing Vinyl Stair Treads with Musson 3 Wide Double-Face Tape
Instructions for Installing Vinyl Stair Treads with Musson 3 Wide Double-Face Tape (For No. 300 & No. 334 treads see special note in the Installation of Vinyl Stair Tread section below) Where To Install
More informationCardboard Model Buildings
Cardboard Model Buildings Get more model kits from http://www.modelbuildings.org PRINTING & ASSEMBLY TIPS: These OO designs can easily be resized by reducing the print percentage as follows: OO scale is
More informationInstallation Guide. Aspect Stone Peel & Stick Tile. proper surface preparation is essential for a successful project. Installations Methods
Aspect Stone Peel & Stick Tile Installation Guide E proper surface preparation is essential for a successful project Failure to follow recommended surface preparation instructions may void the warranty.
More informationRepairing Sheet-Molded Compound (SMC) With Epoxy
Repairing Sheet-Molded Compound (SMC) With Epoxy 1. Properties: A. It does not dent. B. It does not rust C. Panels are formed using a flat sheet or compound that is heat molded in a press. 2. Preparation
More informationSupplies required to build a cardboard boat. (SAMPLE BOAT)
! 1 Supplies required to build a cardboard boat. (SAMPLE BOAT) 1. A sharp cutting tool 2. 1 quart (or more) of contact cement - (Gallon size shown) 3. 2 tubes (or more) of construction adhesive (like Liquid
More informationLittle Briana Cottage Dollhouse assembly instructions
Little Briana Cottage Dollhouse assembly instructions NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also gives
More informationThe Fyfe Building Instructions for Assembly of the N scale kit.
The Fyfe Building Instructions for Assembly of the N scale kit. Kit Contents: 150 each laser cut 1/16" acrylic parts. 6 each 020 adhesive backed part 6 each column caps 2 each decorative canopy 1 each.125"
More informationBig Oz. Rocket. User Guide V0313
Big Oz Rocket User Guide 59824 V0313 Materials Included The Big Oz Rocket Kit should include the following materials. If something is missing, contact Customer Service at 800-358-4983. 20-ounce plastic
More informationINSTALLATION GUIDE VERSION 11/14
INSTALLATION GUIDE VERSION 11/14 In this guide we will demonstrate effective techniques and methods for installing EDGE stainless steel sinks seamlessly in both laminate and solid surface. These techniques
More informationINSTALLATION INSTRUCTIONS
VESDURA VINYL PLANKS 3MM PVC GLUE DOWN - OAK COLLECTION Safety First CAUTION Asbestos Warning in existing floor. Do not sand, dry scrape, bead blast or mechanically pulverize existing resilient flooring.
More information5If the protruding part is. 6Place 1 as is shown in the. 7Place what was assembled
Yamato: Step-by-step 49 The base of the bridge and strakes a c b d a Base of the bridge b Base of the bridge c Base of the bridge d Strakes x 10 THE BASE OF THE BRIDGE 1Smooth 1 to 3, first using the metal
More informationThree layer Felt Roofing using cold applied adhesive
Three layer Felt Roofing using cold applied adhesive Useful tips - Skill level - Safety - Felt Roofing Materials - Tools and Equipment Laying a felt roof is within the capabilities of most diy people providing
More informationHandrail H Series. Product Installation. Instructions. Installation Instructions For. Wall Mounted and Freestanding Round Handrails
Product Installation Installation Instructions For Instructions Handrail H Series Installation Instructions for Wall Mounted and Freestanding Round Handrails Step Nosing F Series Concrete and Timber Step
More informationInstallation Guide. Pionite Decorative Surfaces One Pionite Road, Auburn, Maine PIONITE ( )
Installation Guide A Subsidiary of Panolam Surface Systems SMPBRO00-012 6/14 Pionite decorative laminates are designed for finished interior surfaces which require high impact, wear and stain resistance
More informationThe Saint Paul Building
The Saint Paul Building Instructions for Assembly of The Saint Paul Building. Kit Contents: 65 each laser cut acrylic parts. 1 each sheet of AC roof unit parts. 1 each sidewalk. 3 each Window Glass Templates,
More informationBasic Instructions. Preparing the Moulds
Preparing the Moulds Basic Instructions 1. Make sure the moulds are clean and free of plaster residue (see our CARE & CLEANING instructions for more information). 2. Rinse the moulds in warm water and
More informationInsta-DE2a/2aF Series
Insta-DE2a/2aF Series Self-Adhesive Dry-EraseFront Projection Screen Film with Frame Border and Pen Tray User s Guide Thank you for choosing the Insta-DE2a Series dry-erase whiteboard projection screen!
More informationHow to install Magic Metal
How to install Magic Metal First you need the following tools: Glue: Indoor Out Door Carpet Glue 3 gallon pail. A few rollers (the thinner nap the better) a pan with liner. A good utility knife with extra
More informationBuilding the Gothic Church
Building the Gothic Church Mold #54 does not contain all of the blocks to build this church. You will need extra regular blocks (1/2" x 1/2" x 1") and square blocks (1/2" x 1/2" x 1/2"). These blocks can
More informationMustang Eleanor Style Louvers - Pre-painted (05-10) - Installation Instructions
Mustang Eleanor Style Louvers - Pre-painted (05-10) - Installation Instructions The below installation instructions work for the following products: Mustang Eleanor Style Louvers - Pre-painted (05-10)
More informationINSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5232
INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5232 QCI5232 Rev 0 Page 1 Certified 06/20/2016 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay
More informationDASH KIT INSTALLATION
ÿÿÿÿÿ ÿÿÿÿÿÿÿÿÿÿÿÿ ÿÿÿ ÿÿÿÿÿ ÿÿ ÿÿÿ ÿÿÿÿÿÿÿÿÿÿÿÿÿÿ ÿÿÿÿÿÿÿÿÿÿ ÿÿÿÿ ÿÿÿÿ ÿÿ ÿÿÿÿÿ ÿÿÿÿÿÿÿÿ PROUDLY MADE IN THE USA DASH KIT INSTALLATION These instructions are aimed at the do-it-yourself installer. Read
More informationCUSTOM SHUTTERS IN-A-BOX
CUSTOM SHUTTERS IN-A-BOX SHUTTER ASSEMBLE INSTRUCTIONS & INSTALLATION INSTRUCTIONS 1. Inspect the contents of your package. Do not discard the shutter packaging box until you have started painting your
More informationMax Launch Abort System Prod. No *Kevlar is a registered trademark of Dupont
Flying Model Parts List Max Launch Abort System Prod. No. 3014 A 11820 - Body Tube 3.5 Diam x 5.5" Long B 11824 - Orange Capsule Base Shoulder Ring C 16032 - Laser-cut Ring motor mount rear D 16033 - Laser-cut
More information1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A
1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com
More informationSurf-N-Skim and Surf Pad System Installation Instructions
Surf-N-Skim and Surf Pad System Installation Instructions Tools & Materials: Warm, clean, dry and well lit working environment; flexible straight edge or chalk line; single edge razor; plastic squeegees;
More informationQWALL 5.2 (2 Back Panels)
QWALL 5. ( Back Panels) SHOWER ACRYLIC WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date
More information2. Sanding the Modules Sand the entire surface of each cyc module with 60-grit sandpaper. This will provide for better paint adhesion.
ASSEMBLY INSTRUCTIONS SYSTEM SUPER 2.5 EZ Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship your
More informationCobra X Q Construction Tips Construction: Bel y pan
Cobra X Q Construction Tips : The white plastic in this kit is high impact styrene. It can be painted with most types of coatings if light coats are applied this is necessary due to the thickness of the
More informationCIRRUS AIRPLANE MAINTENANCE MANUAL MODELS SR22 AND SR22T CHAPTER 56-30: DOOR GENERAL. Door 56-30: DOOR. 1. General
CIRRUS AIRPLANE MAINTENANCE MANUAL Door CHAPTER 56-30: DOOR GENERAL 56-30: DOOR 1. General The cabin door windows are manufactured of acrylic and adhesive bonded to the door structure. Replacement is accomplished
More informationCoat Rack. Materials: Directions:
Coat Rack 2x2 wooden poplar (foundation of the rack) 3/4 inch diameter wood dowels (5-8 depending on how many arms you want) 1/4 inch dowel screw 1/4 inch drill bit Power drill Ruler Pencil Paint/spray
More informationUNIT No. 15 & 16 SHOWER DOOR INSTALLATION INSTRUCTIONS
UNIT No. 15 & 16 SHOWER DOOR INSTALLATION INSTRUCTIONS Page 2 of 7 MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure; tempered glass and anodized aluminum. To assure a
More informationFidelity & Guaranty Building
Fidelity & Guaranty Building N Scale Model Kit Instructions for Assembly of the Fidelity & Guaranty Building Kit Contents: 69 each laser cut acrylic parts. Sidewalk material 1 each Window Glass Templates
More informationArtificial Grass. Fitting Guide
Artificial Grass Fitting Guide Quick Start Artificial grass is quick and easy to fit, we have a quick-start guide below or continue on for a more in depth how-to guide. We recommend you have a quick read
More informationCockpit Kit. Full Depth - Builds Quickly - Light Weight READ THROUGH THIS INSTRUCTION MANUAL FIRST. IT CONTAINS IM- laser cut wood kit
The Savage Light Sukhoi Su- 27 Cockpit Kit contains everything you need to build a full depth semi scale Su-27 cockpit, yet adds less than an ounce to your finished model s weight (not including pilot).
More informationSawn Baluster Sizing and Installation Guide
Sawn Baluster Sizing and Installation Guide Welcome to the Durabrac sizing and installation guide for Sawn Balusters. This guide has been prepared to answer any questions you may have about our Sawn Balusters
More informationWall Panel Installation
Wall Panel Installation Special care must be taken in handling of panels with grout lines, especially in cold weather. The indented grout lines are by necessity a little thinner than other areas of the
More informationPRO CYC PRO CYC, INC. SYSTEM SUPER 3EZ
ASSEMBLY INSTRUCTIONS SYSTEM SUPER 3 EZ Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship your
More informationVinyl Installation Guide and Tips
Vinyl Installation Guide and Tips Tools Needed: Squeegee; Grease Pencil (white or blue only!); 2" & 1/4" Masking Tape Prepare your surface and vinyl as outlined on back cover prior to employing this technique
More informationQuality Marine Equipment Since Antifouling Paint For Metal Under The Waterline ROLLER. Application Instructions.
Quality Marine Equipment Since 1981 Antifouling Paint For Metal Under The Waterline ROLLER Application Instructions www.antifoulingpaint.net THANK YOU! Thank you for selecting Velox Plus Antifouling Paint
More informationRoll Out Vinyl Installation Guide
Sub-floor Requirements The contractor performing the installation of the performance vinyl flooring must ensure the proper quality of the sub-floor. The sub-floor must be clean, smooth, permanently dry,
More informationFRAMED SLIDING DOOR FOR TUB OR SHOWER ENCLOSURE 6150A-7150A
FRAMED SLIDING DOOR FOR TUB OR SHOWER ENCLOSURE 6150A-7150A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com
More informationInstallation Instructions
Please read all instructions before installing products. STORAGE: Keep crates in the upright position. When unpacking, store panels flat in a clean dry place. BEFORE INSTALLATION: Check for damage that
More informationTools: Drill/Driver Kreg Jig Miter Saw Jigsaw Circular Saw Adjustable Square Tape Measure Veneer Trimmer Sandpaper and Sander
R PROJECT PLANS DROP-FRONT DESK Create a workspace almost anywhere with this drop-front desk. Mounted to a wall, it doesn t take up any floor space, which means you can hang it wherever you need to work.
More informationMousetrap Catapult. About this project:
Designed by: Ritchie Kinmont Project #44 Page 1/19 About this project: The is fun for ages four and up. Using a mousetrap for the spring, this catapult is designed to throw objects such as practice golf
More informationInstallation Instructions
Installation Instructions The instructions below are recommendations from Deziner Panels on how to install our Recycled Timber mosaic tiles and interlocking panels. Deziner Panels would like to recommend
More informationINSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233
INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233 QCI5233 Rev 0 Page 1 Certified 06/20/2016 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay
More informationBPF Toyota Tundra Mesh Installation Guide
BPF 2007-2009 Toyota Tundra Mesh Installation Guide www.bpfabricating.com Tools Required Philips Screw Driver Flat Head Screw Driver Dremel or Rotary Tool Hand Saw or Multi Max Adjustable Square Tape Measure
More informationProduct number TS-CS/12 x 12. Please read the following before attempting to install your new 12 x 12 Contemporary cast marble panel system
Mincey Marble Mfg., Inc. 4321 Browns Bridge Road Gainesville, GA 30504 Ph: 800.533.1806 Fx: 770.531.0935 www.minceymarble.com Installation Instructions for Mincey Marble Manufacturing s 12 x 12 Contemporary
More informationClay Modeling Film. Features of Clay Modeling Film. Use Clay Modeling Film
Clay Modeling Film The series of Clay Modeling Film, originally developed by TOOLS INTERNATIONAL Corp, is mainly used for interior/exterior shape confirmation, checking highlights and qualification studies
More informationPower Tape Rubber and Vinyl Stair Treads
Power Tape Rubber and Vinyl Stair Treads Installation and Maintenance Instructions Introduction Johnsonite Power Tape is a high strength, polyester thread reinforced, double-sided adhesive tape system
More informationPAINTING AND DECORATING E2
Unit no: 280 Unit title: Prepare a work area ready to commence decorating Credit Value 1 Guidance: For this unit, any area that is suitable for painting and decorating may be used. Safely prepare a work
More informationGrade 11 Woods Lift Lid Coffee Table. Based on Under the big Top from Popular Mechanics Website
Grade 11 Woods Lift Lid Coffee Table Based on Under the big Top from Popular Mechanics Website TABLE TOP 1. Select enough lumber to construct a top that is between 22 ½ and 24 wide after jointing. Ensure
More informationQWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS
QWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationBuilding Instructions
Building Instructions Tools Required Tape measure Straight edge Pencil/pen Jigsaw Table Saw Circular Saw Electric drill 1 Hole saw bit Saw horses/table Protractor Staple gun Caulk gun Paint brush Wrenches
More informationPART NUMBER: T-R20 PACKAGE CONTENTS: GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Scuff Plate TOOLS REQUIRED: APPLICABLE MODELS: 2013 MAZDA CX-
PART NUMBER: 0000-8T-R20 PACKAGE CONTENTS: GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS TOOLS REQUIRED: APPLICABLE MODELS: 2013 MAZDA CX-5 FRONT SCUFF PLATE (Qty 2) 50% ISOPROPYL ALCOHOL/RESIDUE FREE
More informationEZYSTONE WORKSURFACES
EZYSTONE WORKSURFACES Installation & Maintenance Instructions 1. Tools Required Worktop Edge Finishing Kit Pack 1-100mm Velcro Backing Pad Pack 2-100mm Diamond Dry Cut Velcro Discs (100 Grit Yellow) (200
More informationGENERAL INSTRUCTIONS. Woodland Scenics PO BOX 98, LINN CREEK, MO woodlandscenics.com PREPARE PLASTIC PARTS PREPARE METAL CASTINGS
#40700 Popa Weelie's Saloon INSTRUCTIONS CAUTION: Cutting tools recommended. Use with care. This item is not a Children s Product and is not intended for use by Children. Conforms to Health Requirements
More informationKam Aero 43% Extra 300.
Stab Sheeting Kam Aero 43% Extra 300. Stabs / Elevator: Make your skins using the same method as you did for the fuselage foam parts. The stabs require 8 sheets (4 per stab) of 4 x 48 A grain sheeting.
More information340 & 350 SERIES DELUXE FRAMELESS BYPASS
BATH ENCLOSURES An Alcoa Company Tel: 800-643-1514 Fax: 870-234-3181 www.alumaxbath.com INSTALLATION INSTRUCTIONS 340 & 350 SERIES DELUXE FRAMELESS BYPASS BATH ENCLOSURES Copyright Alumax Bath Enclosures
More information