Entrance Cabinet Plans
|
|
- Stanley Gray
- 5 years ago
- Views:
Transcription
1 Entrance Cabinet Plans Page 1 of 19
2 Introduction I have tried to ensure all steps are covered in these plans but if you find any errors in the plans or have a question then please me at info@andrewharriswoodwork.com to let me know. All my builds are made with pocket hole joinery. You will need a pocket hole jig tool such as a Kreg Pocket Hole Jig in order to build them. Shopping List Size Length Quantity Board Number 2 by 2 6 feet 2 1, 2 1 by 2 8 feet 4 3, 4, 5, 6 1 by 3 8 feet 2 7, 8 1 by 4 8 feet 4 9, 10, 11, 12 1 by 4 6 feet by 6 6 Feet 1 14 Drawer slides 14 inch 2 pairs ¼ inch plywood 24 ¾ by 11 ¾ minimum for back panels Quantity 2 ¼ inch plywood ¾ inch plywood ¾ inch plywood For drawer bottoms and back panels. See build notes as will depend on method of drawer construction 14 by Quantity 2 for side inserts. 34 ½ by 15 ½ for bottom shelf. You will also need: Pocket Hole Tool such as a Kreg Pocket Hole Jig 1.25 inch pocket screws 1.25 inch wood screws ¾ inch finishing nails Wood glue Drawer/Door pulls 4 door hinges Estimated Material Cost: $200 plus cost of door/drawer pulls and hinges Page 2 of 19
3 Cut list Please read all instructions before cutting wood as shown below. I suggest some pieces are cut as you go to ensure a tight fit. Size Length (inches) Quantity Used For Board Number 2 by Legs Two from board 1 and two from board 2 1 by Front top rail and middle rails and rail for screwing top to 1 by Top rails for sides 4 1 by Vertical front support 3 1 by Vertical support between drawers 1 by Drawer rail supports 4 1 by Drawer rail supports 6 1 by Bottom rail for sides 7 1 by Front bottom rail 7 1 by 3 19 ¾ 4 Door 8 1 by 3 10 ½ 4 Door Three from 7 and one from 8 1 by Back top and bottom rails One from 9 and one from 12 1 by 4 24 ¼ 1 Back vertical support 9 1 by 4 14 ¾ 4 Drawer sides One from 12 and three from13 1 by 4 13 ¼ 4 Drawer front and back One from 12 and one from 13 1 by Top Two from 10, two from 11 and two from 12 1 by 6 15 ¾ 2 Drawer Fronts by 0.5 inch 1.5 by 0.5 inch 15 ¾ 4 Poplar for drawer trim. Cut to fit once drawer is made and drawer front fitted. 5 ¾ 4 Poplar for drawer trim. Cut to fit once drawer is made and drawer front fitted. ¼ by 1 ½ trim 16 4 Back of door trim ¼ by 1 ½ trim 8 3/4 4 Back of door trim Page 3 of 19
4 Size ¾ inch plywood ¾ inch plywood ¼ inch plywood ¼ inch plywood ¼ inch plywood Length (inches) Quantity Used For Board Number 14 by For side inserts 34 ½ by 15 ½ 1 Bottom shelf 11 ¾ by 16 2 Door backs 14 ¾ by 14 ¾ 2 Drawer bottoms 24 ¾ by 11 ¾ 2 Back Panels Page 4 of 19
5 Step 1 Make the two Side frames Join two of the legs together using the 1 ½ by 14 for the top rail and the 2 ½ by 14 for the bottom rail. Make sure the gap between the rails is 27 ¼ inches. Page 5 of 19
6 Step 2 Add side inserts The sides in the plan are slightly different to the picture shown and are just solid panels as easier to make. I actually like to use 1 by 4s joined together with a 45 degree bevel if you have a router. That is more work though and depends if you want to do it but does give a nicer look. Note if you took this approach then as the 1 by 4s may not be exactly 1 by 4 then do not use glue in the first step incase you need to trim the length of the side top and bottom rails. Page 6 of 19
7 Step 3 Add front Rails Add the two 1 by 2 and the one 1 by 3 horizontal front rails as shown and then the two 1 by 2 vertical rails. I would suggest cutting those vertical rails once the horizontal ones are in place to ensure a tight fit. Page 7 of 19
8 Step 4 Add Back rails and support Add the two horizontal three vertical 1 by 4 rails as shown below. Page 8 of 19
9 Step 5 Add the bottom Shelf Cut a ¾ inch square notch out of each corner of the plywood measuring 34.5 inches by 15.5 inches. Drill pocket holes at the edge of each side and approximately 6 inches apart equally spaced along each side. Fix the bottom shelf using pocket hole screws from flush with the top of the rails using pocket hole screws. Make sure the pocket hole screws are on the bottom. Leave a 1 inch gap between the bottom edge of the shelf and the bottom of the rail. Page 9 of 19
10 Step 6 Make the Doors Drill pocket holes at both ends of the two shorter pieces and make the doors as shown below. Remember the total width of the door should be ¼ inch less than the width of the opening for the door. Same applies to the height of the door and the height of the opening for. Page 10 of 19
11 Step 7 Door Insert Fix ¼ inch thick ply to the back of the door overlapping the frame by at least ½ inch to allow fixing. I like to overlap sufficiently to try to cover the pocket holes and then add 1 ½ inch trim around the edge of the back just to tidy it up but the diagram below shows the minimum size you would need. Page 11 of 19
12 Step 8 Drawer rail supports Add drawer rails supports as shown using the 14 inch lengths of 1 by 2 for the outer ones and the 15 ½ inch 1 by 2 s for the two inner ones. The bottom of the support rail should be flush with the top of the front horizontal rail. Page 12 of 19
13 Step 9 Drawers Drill pocket holes in the both ends of the 13 ¼ inch length 1 by 4 drawer pieces. Join 13 ¼ inch pieces to the 14 ¾ inch lengths of 1 by 4 to form the drawers. Cut two 14 ¾ by 14 ¾ pieces of ¼ inch plywood for the bases. Fix the plywood base to the bottom with ¾ inch finishing nails and glue. I prefer to use a router to make the base inserted into the sides but nailing to the bottom will work fine. Page 13 of 19
14 Fix the drawer part of the drawer slide to the bottom of the drawer. I suggest you make the front edge of the slide sit flush as shown in the photograph below. Page 14 of 19
15 Step 10 Fitting the drawer rails Fit the outer side parts of the drawer rails so that the leading edge is flush with the back edge of the front lower rail and the bottom edge of the rail is half an inch above the top of the rail. (excuse the basic block drawing for the rail) Step 11 Fitting the drawer The drawer should then sit with half inch clearance from the bottom rail. Page 15 of 19
16 Step 12 Fit Drawer Front The drawer fronts are the 1 by 6 pieces measuring 15 ¾ inches long. Drill two holes through the inner drawer front shown in the picture in step 10 and then fix the outer drawer front by screwing through the inner drawer front into the outer drawer front using 1 ¼ inch screws. Tip clamp the drawer front in position when happy with the spacing and then screw it in place. There should be a 1/8 inch gap all around the outer drawer front. Step 13 Fit backing Cut two pieces of ¼ inch plywood at least 12 ¼ by 25 ¼ and use ¼ inch finishing nails to nail them to the back of the cabinet from the inside. Page 16 of 19
17 Step 14 Making the Top Use 5 pieces of 1 by 4 measuring 38 inches length and join them together with pocket hole screws to make the top. The top will be 17.5 inches deep. Tip Make sure you place the outermost pocket holes at least an inch from the edge so that they do not protrude outside the edge of the cabinet and can t be seen. Sand the top so that the boards are flush with each other and joins not visible (unless you want them to be). Page 17 of 19
18 Step 15 Fitting the Top On the sides and back rails drill pocket hole screws facing upwards to use to fit the top. On the front the 1 by 2 rail is not deep enough to drill pocket holes in. Instead fit another 1 by 2 behind it and screw it to the inside of the front rail and drill holes for in it for fixing the top through. Place the top with the good side down and then place the upturned cabinet on top. Make sure you have equal gap all around and then fix with 1 ¼ inch pocket hole screws on sides and back and 2 inch screws on the front edge. Page 18 of 19
19 Step 16 Drawer Trim Cut the drawer trim to fit once the drawer front is added. Fix in place with glue and 1 ¼ inch finishing nails. I like to evenly space the nails and leave the small nail head holes showing for a more rustic finish. I like to use the ½ inch thick poplar for the trim as It provides a slight contrast when stained. Step 17 Optional Shelf A shelf can also be added. If you want to add shelf then you will need 4 lengths of 1 by 4 at 34 ½ inches long each or piece of ¾ inch plywood measuring 14 by 34 ½ inches. If using 1 by 4 then join them with pocket holes. Then either fix side rails as supports at desired location or use a shelf pin jig to drill holes where you want the shelf and support it with shelf pins. The wood for the shelf is not included in the shopping list or cut list. Step 18 Finish Sand well to smooth our joints and remove any wood glue residue. Apply Pre stain and your choice of color or paint as desired. Step 19 Hardware Add hardware of your choice. I also fit magnetic latches to the inside of the doors and frame to stop the doors from going inside the cabinet. Page 19 of 19
Chest of Drawers Plans
Chest of Drawers Plans www.andrewharriswoodwork.com Page 1 of 15 Introduction This plan makes a chest of drawers that is 50 inches at the widest point, 19 inches deep and 40.75 inches high. I have tried
More informationChest of Drawers Plans
Chest of Drawers Plans www.andrewharriswoodwork.com Page 1 of 12 Introduction This plan makes a chest of drawers from 2 by 4s and 2 by 6s for the top. The cabinet is 22 ½ inches at the widest point, 22
More informationGrilling Table. Page 1 of 10
Grilling Table www.andrewharriswoodwork.com Page 1 of 10 Introduction This plan makes a table 47 inches wide, 22 inches deep and 36 inches high with the top added. All my builds are made with pocket hole
More informationMudroom Unit. Page 1 of 25
Mudroom Unit www.andrewharriswoodwork.com Page 1 of 25 Introduction This plan makes a unit which is 66 ¾ inches tall, 39 ½ inches wide and 18 ½ inches deep. It was custom made for some friends to fit the
More informationFull Size Bed The Jocelyn
Full Size Bed The Jocelyn www.andrewharriswoodwork.com Page 1 of 14 Introduction This plan makes a bead frame for a full size mattress. Although a full size mattress should be standard size. Please make
More informationCastle Bed. Page 1 of 24
Castle Bed www.andrewharriswoodwork.com Page 1 of 24 Introduction This plan makes a twin bed that is 91 inches long and 60 inches wide. I have tried to ensure all steps are covered in these plans but if
More informationPatio Table. Page 1 of 16
Patio Table www.andrewharriswoodwork.com Page 1 of 16 Introduction This plan makes a table that is unit which is 95 ½ inches long and 49 inches wide. The distance from the underside of the top edging to
More informationHow to Build a Recessed Medicine Cabinet
How to Build a Recessed Medicine Cabinet See post for install info http://www.hertoolbelt.com/recessed-medicine-cabinet/ Materials 6 Inset Cabinet Door Hinges 3 Latches 1 sheet Beadboard or 1/4 plywood
More informationCode Description Qty. Material Dimensions A Long Inner 4 2 x 4 pine 34-1/2 long
B utler s Chest Because it s designed to suit a variety of purposes, this butler s chest is a piece of furniture that absolutely anyone can appreciate. Used by itself, it can serve as an end table or can
More informationDIY Rustic Dresser Addicted2DIY.com
DIY Rustic Dresser Addicted2DIY.com *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever using
More informationMaterials. Special Tools and Techniques Chisel Long pipe clamps Miters Router with 1/2" rabbet cutter Rabbets Dadoes. Hardware
D esk Our executive desk was built with specific needs in mind. We wanted a large desktop, large drawers, and a cubbyhole to house a rollaway hanging file cabinet. We are thrilled with our finished project.
More information(1) 2x4 Ft. Sheet of ¼-inch Plywood. 1 ¼-inch Wood Screws. 1 ¼-inch Brad Nails ¾-inch Brad Nails Wood Glue CUT LIST:
MATERIALS: (5) 1x3x8 Ft. Boards (3) 2x4x8 Ft. Boards (10) 1x4x8 Ft. Boards (1) 1x2x10 Ft. Board (1) 2x2x4 Ft. Board (2) 1x6x8 Ft. Boards (1) 4x8 Ft. Sheet of ¾-inch Plywood (1) 2x4 Ft. Sheet of ¼-inch
More information129 KITCHEN BASE CABINET 480
129 KITCHEN BASE CABINET 480 There are two sorts of kitchen cabinets: base cabinets, which sit on the floor, and wall cabinets. Base cabinets provide both storage space and work surfaces. They often house
More informationModern Farmhouse Printer Cabinet. Addicted2DIY.com
Modern Farmhouse Printer Cabinet Addicted2DIY.com Before beginning this project please read through all of the plans as well as the blog post associated with this project. Always use safety precautions
More informationPROJECT PLANS MULTIPURPOSE WORK CENTER
R PROJECT PLANS MULTIPURPOSE WORK CENTER This handy project can provide the work space you need anywhere in your home. Whether you need that work space in the shop, the garage, the basement, or in a laundry
More informationThis indicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
S i m p le Woodworking: What You'll Need v lumber 2-1 x 12 x 6 hardware/supplies (availability will vary) 1 1/4" pocket hole screws #18 x 1 1/2 brads or pocket hole plugs 12-inch continuous hinge magnetic
More informationirdhouse Table Special Tools and Techniques Materials and Supplies Hardware
B irdhouse Table This whimsical table is one of our favorite projects, because it never fails to produce a smile on the faces of our backyard guests. Not only is it cheerful to behold but the glass top
More informationrmoire Materials Hardware
A rmoire No house ever has enough storage space, and I built this armoire to satisfy a couple of needs. Inside the armoire is a shelf large enough for the television. Under the shelf are six drawers that
More informationDIY Wine Storage Cabinet
DIY Wine Storage Cabinet ADDICTED2DIY.COM *Before beginning this project, please read through all of the plans and the blog post. When building this project, be sure to measure your wood and cut to fit.
More informationrmoire This attractive and practical two-door armoire takes up very little floor space in a bedroom but provides lots of storage. Because it is only
A rmoire This attractive and practical two-door armoire takes up very little floor space in a bedroom but provides lots of storage. Because it is only a little over 1 foot deep, it s easy to incorporate
More informationKreg Tool Co. All Rights Reserved.
Version 1 p. 1 Materials: Lumber: Qty: Board 2 2x2s 3 ft. long 2 1x2s 8 ft. long 2 1x3s 8 ft. long 6 1x6s 10 ft. long INSTRUCTIONS: Supplies: 1 1 / 4" Kreg Screws (coarse thread for softwoods, fine thread
More informationMaterials and Tools: Printer s Triple Console Cabinet. Free Plans to build a Triple Console Cabinet
Materials and Tools: Materials: 3 sets euro style bottom corner mount drawer slides, 16 length 3 sets inset hinges 24 cup style handles 8 2x2 @ 8 feet long 6 1x3 @ 8 feet long 6 1x2 @ 8 feet long 1 sheet
More informationHudson Dresser [1] Hudson Dresser Published on Ana White ( Submitted by dan-k [2] on Fri, :43 [1]
[1] Submitted by dan-k [2] on Fri, 2011-03-11 11:43 [1] If you plan on staining this piece, it is recommended that you stain all of the drawer face materials before assembly for a more professional look.
More informationIndustrial Cart. Materials. With High Style Restyle
1 Industrial Cart With High Style Restyle Materials 1 sheet 3/4" plywood 1-1" x 2" x 8' board 2-1" x 3" x 8' board 1-2" x 8" x 10' board 1-2" x 6" x 8' board 3-1/4" x 2 1/2" x 4' poplar hobby boards, or
More informationDIY Farmhouse Cabinet
DIY Farmhouse Cabinet Addicted2DIY.com *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever
More informationPlans. Easy-to-Build Full-size Deluxe Murphy Bed Plan. For more plans, tools and hardware visit rockler.com
Easy-to-Build Full-size Deluxe Murphy Bed Plan Build a full-size Deluxe Murphy Bed complete with decorative molding and matching side cabinets! Plans For more plans, tools and hardware visit rockler.com
More informationPROJECT PLANS EXPANDABLE CRAFT CENTER
R PROJECT PLANS EXPANDABLE CRAFT CENTER Whether you re working on craft projects, sewing, or pursuing another hobby, this craft center offers a great place to work. It features a large work surface that
More informationJewelry Cabinet. Materials: 5/8" brad nails 5-1" x 3" x 8' boards (or if not 2 1/2" wide. 1-4' x 8' sheet - 3/4" plywood. wood glue get 1x4's)
1 Jewelry Cabinet Materials: 1-4' x 8' sheet - 3/4" plywood 5/8" brad nails 5-1" x 3" x 8' boards (or if not 2 1/2" wide wood glue get 1x4's) sand paper 1-1" x 6" x 8' board wood filler 1/2 sheet - 3/16"
More informationDIY Full-Size Captain s Bed with Storage. Addicted2DIY.com
DIY Full-Size Captain s Bed with Storage Addicted2DIY.com Before beginning this project Please read through all of the plans as well as the blog post associated with this project. Always use safety precautions
More informationJeff Branch WOODWORKING YOU CAN BUILD A. By adding subtle design elements, a traditional furniture style becomes decidedly modern.
Jeff Branch WOODWORKING YOU CAN BUILD A By adding subtle design elements, a traditional furniture style becomes decidedly modern. Jeff Branch WOODWORKING Publisher: Jeff Branch Editor: Jeff Branch Art
More informationWoodline USA Woodline Spacer Fence System
Woodline USA Woodline Spacer Fence System MADE IN THE USA Includes: (1) ¼ Spacer Fence (1) 3/8 Spacer Fence (1) ½ Spacer Fence (1) Hardware Package (1) 3 Piece Brass bar set (2) Setup Blocks Visit Us Online
More informationCUT LIST. Hidden Study: The Towers - Page 2. ¾" x 4' x 8' plywood. ¾" x 4' x 8' plywood. ¾" x 4' x 8' plywood. ¾" x 4' x 8' plywood. SHanty-2-Chic.
Copyright 2015 Shanty-2-Chic.com Hidden Study W THE Towers hat a magnificent personification of your DIY skills. The catch? It doesn't need anything more than a little patience and basic hands on approach.
More informationThe Q Frame PROJECT. a picture frame with secrets created exclusively for the Router Forum
The Q Frame PROJECT a picture frame with secrets created exclusively for the Router Forum 007 OR RELEASE FPLANS APPROVED The Q Frame: Project Overview LIST OF MATERIALS Frame Sides & Face 3/4 x 5 1/2 x
More informationEntryway Locker 17 ½ 25 ½
Copyright 2015 Shanty-2-Chic.com T Entryway Locker his old world entryway locker is loaded with possibilities. Two adjustable shelves allow you to customize the storage to fit your needs. Even better,
More informationDrill Press Storage Cart
Drill Press Storage Cart Richard Hicks on July 22, 2013 Drill Press Storage Cart Drill Press Storage Cart My Inspiration ShopNotes Issue 128 Changes Used casters instead of wheels Didn t build the drill
More informationFarmhouse Vanity 24-¼ 21-½
opyright 2015 Shanty-2-hic.com I Farmhouse Vanity nspired by simpler days of the past, this vanity is built with sophisticated charm and character. ozy and freestanding, this base can be paired with any
More informationI love the outdoors. And I m impressed with whatever forces in the universe have made it possible for me to purchase a collapsible canvasand-metal
Limbert Chair 9 I love the outdoors. And I m impressed with whatever forces in the universe have made it possible for me to purchase a collapsible canvasand-metal camp chair for under $20. But when you
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 3
Kentucky 4H Wood Science Plans Notebook Plans Level 3 MATERIALS: 2 pieces wood 3/4 x 10 x 4 1 piece wood 3/4 x 12 x 4 2 pieces wood 3/4 x 3 x 2 5 1/2" 2 pieces wood 3/4 x 3 x 1 8 1 piece wood 2 x 4 x
More informationining Table Materials *Notes on Materials
D ining Table We looked around for the perfect table for the dining room. Some were too big, some too small, and most were just too expensive. So we built this one, and we are happy with the result. It
More information1 ¼-inch Pocket Screws Brad Nailer or Hammer 1 ¼-inch Brad Nails Clamps
MATERIALS: TOOLS: (4) 2 x 6 x 8 Ft. Boards Tape Measure (2) 2 x 4 x 8 Ft. Boards Carpenter s Square (7) 1 x 4 x 8 Ft. Boards Pencil (2) 1 x 3 x 8 Ft. Boards Drill (1) Half Sheet of ¾-inch Thick Plywood
More informationPLANS BY TOM BURY MURPHY WORKTABLE TOTAL DIMENSIONS: FOLDED UP 30 X 48 X 0 FOLDED DOWN 30 X 58 X 84
MURPHY WORKTABLE TOTAL DIMENSIONS: FOLDED UP 30 X 48 X 0 FOLDED DOWN 30 X 58 X 84 MATERIALS LIST: (2) 2 x8 x8 (3) 2 x4 x8 (1) 1 x2 x8 (1) 48 x96 3/4 plywood (2) 1-1/2 x30 continuous hinge (1) Left-side
More informationPROJECT PLAN TOOL CHEST
BUILD IT WITH ROCKLER PROJECT PLAN TOOL CHEST FEATURING ROCKLER S BUILD QUESTIONS? Go to www.rockler.com or call 800-279-4441 Stock # Item 63420 1/4" x 24" x 30" Baltic Birch Plywood 63446 1/2" x 24" x
More informationPatrol Box Plans by David J. Yarusso Troop 609
Patrol Box Plans by David J. Yarusso Troop 609 Materials List: 1. One 4 x8 sheet of ½ thick cabinet grade (birch or oak) or AC plywood. If using AC grade, use the A grade surface on the outside for a clean
More informationwoodworkersjournal.com MATERIAL LIST
MATERIAL LIST T x W x L 1 Legs (2) 1 1 2" x 3 1 2" x 36 7 16" 2 End Uprights (2) 1 1 2" x 3 1 2" x 32 1 2" 3 Stringers (4) 1 1 2" x 3 1 2" x 42" 4 Top Cladding, Long (2) 3/4" x 7 1 4" x 65 3 4" 5 Side
More informationCounter Height Bar Stool [1]
Counter Height Bar Stool [1] Submitted by AndyH [2] on Wed, 2015-03-11 09:58 These stools are ideal for a kitchen counter and I made them to fit ours [1] Page 1 of 10 which is about 36 inches from the
More informationMODERN BED FRAME ROCKLER BUILD IT WITH BUILD SIMPLIFY CUSTOMIZE. Plan Value $14.99
BUILD Stock # Item 63446 Baltic Birch Plywood /2" x 24" x 30" (2 qty) Stick veneer - Maple 24" x 96" 3/8" Dowels - Birch Bed Connector Hardware I-Semble Platform Bed Frame - Queen 3/8" Beadlock Basic Starter
More informationMedia Console Table 38"
Copyright 2016 Shanty-2-Chic.com Media Console Table A sleek, modern take on a traditional concept; this console table is as stylish as it is functional and you'll have it done in a weekend. And versatile
More informationComputer Desk. Project designed by April Wilkerson
Project designed by April Wilkerson Copyright WilkerDos.com 2018 Project plan Desk Page 2 of 16 Page 3 of 16 File cabinet Page 4 of 16 Metal base Page 5 of 16 Glue up Get started by gluing up boards for
More informationEmpire Dresser Plans
1 Empire Dresser Plans Materials 1 sheet 3/4" plywood (cabinet grade 4' x 8') 1 sheet 5 mm (3/16") underlayment plywood 4'x 8', buy another 1/2 sheet if you want to put a back on the dresser. 1-2" x 4"
More informationULTIMATE ROUTER TABLE PLANS. By Dan Phalen
ULTIMATE ROUTER TABLE PLANS By Dan Phalen January 2017 Ultimate Router Table Plans. Copyright 2012-2017 by Daniel Phalen. Published by Creston Hall Publishing Company. All rights reserved. No part of this
More informationMaking Pocket-Hole Joints
Tips and Techniques 8 SAFETY FIRST Making Pocket-Hole Joints Before doing this activity, make sure you understand how to use all of the tools and materials safely. Adding pocket-hole screws to strengthen
More informationThis indicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
S i m p le Woodworking: Bath Side Table What You'll Need v lumber 4-1- x 36-inch square dowels 1-1 x8x8 1-3/4-inch x 2- x 4-foot sheet of plywood hardware/supplies 1 1/4" pocket hole screws #18 x 1 1/2
More informationKnobsandPulls.com. Presents. A Simplified Approach to Building Cabinets Using the 32mm System
KnobsandPulls.com Presents the KISS II system. A Simplified Approach to Building Cabinets Using the 32mm System Available online at www.cabsystems.com Revised September 2007 by Joel Ketner or www.kissii.com
More informationChapter 22 - Cabinets & Vanities
Chapter 22 - Cabinets & Vanities Contents Chapter 22 - Cabinets & Vanities... 22-1 Timing & Prerequisites... 22-2 Cabinets... 22-3 Cabinet Layout... 22-3 Wall Cabinets... 22-4 Assemble the Wall Units...
More informationBuilding Instructions
Building Instructions Tools Required Tape measure Straight edge Pencil/pen Jigsaw Table Saw Circular Saw Electric drill 1 Hole saw bit Saw horses/table Protractor Staple gun Caulk gun Paint brush Wrenches
More informationAmerica s leading woodworking authority To download these plans, you will need Adobe Reader installed on your computer. If you want to get a free copy, visit: http://adobe.com/ reader. Having trouble downloading
More informationTongue & Groove Cabinet Doors Copyright 2014 JaysCustomCreations.com
Tongue & Groove Cabinet Doors Copyright 2014 JaysCustomCreations.com A tongue and groove cabinet door is made up of at least 5 pieces. Two horizontal rails (blue), two vertical styles (green), and one
More informationBenchmark Media Console [1]
[1] Submitted by Ana White [2] on Fri, 2011-10-07 13:31 [1] Here she is!!!! Excited to post this plan for you, enjoy the plans! Happy Buiding, Ana Summary: Make your own Pottery Barn inspired Benchwright
More informationOffice Towers 83 ¼ 35 ½ 18 ¼
Copyright 2015 Shanty-2-Chic.com T Office Towers his towering hutch will be admired for years to come. Inspired by rustic, high end furniture found in boutique showrooms it will impress all who see it...especially
More informationReclaimed Wood Look Bedside Table [1]
[1] Submitted by Ana White [2] on Thu, 2011-06-23 12:27 Page 1 of 18 [1] Additional Photos Page 2 of 18 [3] Featured photo by brick [4] This rustic three drawer nightstand is easy to build with off the
More informationDisplay Case (for J&S)
Display Case (for J&S) This is constructed of maple plywood with solid maple (soft maple) edge banding. It was made to fit between a door and a kitchen cabinet, and has an elegant circular taper between
More information136 PLYWOOD DESK 522
136 PLYWOOD DESK 522 Simple in design and inexpensive, this plywood desk is made from a single 4- x 8-foot panel. Plywood is available with many hardwood veneers; it can also be covered with plastic laminate,
More informationRouter bit cabinet August Home Publishing Co.
Router bit cabinet 2011 ugust Home Publishing Co. Feature Project Router Bit Cabinet Dovetail keys at the corners reinforce the joints to make a stronger cabinet. Plus, a clear, plastic door panel lets
More informationBuild a Rolling Tool Tote
The rolling tool tote design calls for readily available materials: a cheap hand truck (it could be an axle and two wheels), 3/4 and 1/2 thick plywood, 1/4 thick MDF (you could use plywood or hardboard)
More informationSilverware Chest Plan
Silverware Chest Plan 05L14.01 Introduction 1. Measure the space required for your cutlery before beginning this project to be sure that it will fit in the drawers and top compartment. The best way to
More information(2) 4 x 8 Ft. Sheets of ¾-inch Purebond Plywood Tape Measure (2) 4 x 8 Ft. Sheets of ¼-inch Purebond Plywood Pencil (1) 1 x 8 x 8 Ft.
MATERIALS: TOOLS: (2) 4 x 8 Ft. Sheets of ¾-inch Purebond Plywood Tape Measure (2) 4 x 8 Ft. Sheets of ¼-inch Purebond Plywood Pencil (1) 1 x 8 x 8 Ft. Board Carpenter s Square (1) 1 x 6 x 8 Ft. Board
More informationKitchen Step Stool. Premium Plan. In this plan you ll find: America s leading woodworking authority
America s leading woodworking authority Premium Plan In this plan you ll find: Step-by-step construction instruction. A complete bill of materials. Construction drawings and related photos. Tips to help
More informationDresser. Materials & Tools FEATURING FORMALDEHYDE-FREE TECHNOLOGY. Free Plans to build a Dresser
Free Plans to build a Dresser Materials & Tools Materials: 1-1/4 pocket hole screws 1-1/4 brad nails 3 sets of 18 drawer slides Drawer pulls Edge banding, optional Wood glue Sandpaper (100, 150, 220 grits)
More informationClassic Kitchen Island
America s leading woodworking authority Step by Step construction instruction. A complete bill of materials. Classic Kitchen Island Exploded view and elevation drawings. How-to photos with instructive
More informationWallbeds Northwest ENDURA CABINET PLANS AND INSTRUCTIONS
Thank you for purchasing your Wall Bed from Wallbeds Northwest. If you have purchased a complete "Endura DIY Kit," then much of the work is already done for you. Please skip to assembly instructions. Note
More informationLARGE PLYWOOD CUTTING GUIDE
Copyright 2015 Shanty-2-Chic.com Workbench I f you are tight on space but large on ideas this bench is just what you need. Sturdy and mobile this bench has an ingenious fold out wing that gives you over
More informationDIY Outdoor Console Table Addicted2DIY.com
DIY Outdoor Console Table Addicted2DIY.com *Before beginning this project, please read through all of the plans. Always use safety precautions whenever using power tools and follow the manufacturer s suggested
More informationKitchen Upper Cabinet: Double Doors Cabinets from Scratch
Kitchen Upper Cabinet: Double Doors by Cabinets from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for any loss, damage,
More informationSINGLE TRACK BYPASS (patent pending) barn door hardware
SINGLE TRACK BYPASS (patent pending) barn door hardware Installation Manual What is included in your kit: Part number Part name Quantity 1 Inner door hanger 2 2 Outer door hanger 2 3 5/16 x 1.5 lag bolts
More informationHow To Create An Entertainment Unit
How To Create An Entertainment Unit Materials required: 2 x Pine Panels - 1800mm x 450mm x 18mm 4 x Pine Panels - 310mm x 450mm x 18mm 1 x Pine Panels - 650mm x 450mm x 18mm 6 x Bun feet (your choice of
More informationNEXUS SERIES CABINETS
NEXUS SERIES CABINETS STANDARD BASE ASSEMBLY INSTRUCTIONS Also applies to: Galaxy Series, Nexus Series, Ridgeline Series, Statesman Series, and Waterford Series FOR YOUR INFORMATION: These assembly instructions
More information786 Kurka Jig Owners Manual
7 Kurka Jig Owners Manual Please Read Carefully! 7 Parts List Parts listed in this box are shown in photos in the instructions. Part Description Quantity 7B Jig Plate Set, pieces..................... Six
More informationThis photo more clearly shows how locating pins are used to transfer the dowel holes from the edge to front of frame. Use bar clamps till glue dries.
CHINA HUTCH 266 The frame sections of the china hutch are assembled with the aid of glue and spiral dowels. Dowel centers are recommended to ease matching of dowel holes. gant chinaware, antique vase,
More informationPULLOUT SHELF ROCKLER BUILD IT WITH BUILD CUSTOMIZE
BUILD Stock Item 12229 Drawer s, 2 1 2" x 48" 63420 Baltic Birch Ply, 1/4" x 24" x 30" 38742 Maple, 3/4" x 3" x 24" 45953 100# Zinc Over-Travel Drawer Slides - Centerline 757-20" 30254 #8 x 1 1 4" Square
More informationPROJECT PLAN OUTFEED TABLE
BUILD IT WITH ROCKLER PROJECT PLAN OUTFEED TABLE BUILD Stock # Item 00 ' Universal T-Track () 0 T-Track Intersection Kit 70 JIG IT Universal Drawer Slide Jig 0 " Drawer Slides () 77 Auto-Adjust Jig Clamp
More informationClassic Storage Wall, Extra Wide Media Unit [1]
[1] Submitted by Ana White [2] on Wed, 2010-01-20 00:40 [1] Summary: This extra wide media base is sturdy and solid, featuring ample storage. If you need more storage, simply add storage bases and hutches
More informationMedia Console with DVD Drawer Storage, Cyndi Collection [1]
Media Console with DVD Drawer Storage, Cyndi Collection [1] Submitted by Ana White [2] on Thu, 2011-05-12 15:32 [1] You see, I'm really quite greedy. I want to build everything, EVERYTHING for myself.
More informationPROJECT PLANS ROLLING LAUNDRY SORTER
R PROJECT PLANS ROLLING LAUNDRY SORTER Sorting laundry certainly doesn t rank high on anyone s list. So, anything that makes this task easier is welcome. If that functionality can be mixed with a bit of
More informationClassic Storage Wall Side Base Units [1]
[1] Submitted by Ana White [2] on Thu, 2010-01-21 00:18 [1] Summary: All the beauty and functionality of expensive built-ins, but none of the cost or limitations. Build this base cabinet to keep your media
More informationMaking a Massive Bookcase Step-by-Step
Making a Massive Bookcase Step-by-Step Jeff Branch WOODWORKING The only thing challenging about this project is its huge size. By JFF BRANCH A t right is a rendering of my first woodworking project completed
More informationHinge Mortising Jig. One of the make it or break it parts of building a. 6 ShopNotes No. 74
Hinge Mortising Jig A Mortise for a Hinge. Quick, clean, and accurate that s the only way to describe the mortise you get with a trim router and this hinge mortising jig. One of the make it or break it
More informationProject 11355EZ: Wall Cabinet with Louvered Doors and Shelf
Project 11355EZ: Wall Cabinet with Louvered Doors and Shelf This Early American style cabinet will look good in any room, although it seems particularly well suited for the kitchen or bathroom. To make
More informationCopyright 2010 Springbok Publishing All Rights Reserved- Page 1
Copyright 2010 Springbok Publishing All Rights Reserved- www.woodensaddlerackplans.com Page 1 Legal Information All contents copyright 2010 by Springbok Publishing. All rights reserved. No part of this
More informationindicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
p i r at e ' s c he s t t oy box What You'll Need lumber 1-1x2x4 1-1x2x8 1-1x3x2 2-1x3x8 1-1x6x4 1-3/4 x 2 x 4 sheet of plywood 1-3/8 or 11/32 x 4 x 8 sheet of beadboard paneling 1-9/16 x 8 feet quarter
More informationBathroom Storage Unit. Wilkerdos.com
Bathroom Storage Unit Wilkerdos.com Copyright 2015 Material List Quantity Item Notes 1 4 x 8 x 3/4 plywood Construction grade 1 2 x 4 x 1/2 plywood Construction grade 11" 7-1/2" Page 1 Some 1 1/4" brad
More informationDesign Update /29/2006
Design Update 3 -- 8/29/2006 Since our first design we ve made many minor changes to key areas of the prayer bench, especially the folding hinge geometry. The general design remains the same, though the
More informationKitchen Upper Cabinet: Single Door Cabinets from Scratch
Kitchen Upper Cabinet: Single Door by Cabinets from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for any loss, damage, disappointment,
More informationKlamp Trak. Instructions (39052)
Klamp Trak TM Instructions (39052) ITEM# KKS1020 - Klamp Trak TM Getting Started There are three main methods for installing Klamp Trak in your workshop. In all three methods, your goal will be to construct
More informationYOU CAN BUILD THE JACKSON DRESSER. Combining traditional styling with rustic materials leads to a classic, yet casual look.
YOU CAN BUILD THE JACKSON DRESSER Combining traditional styling with rustic materials leads to a classic, yet casual look. Jeff Branch CONTENTS Jeff Branch Publisher: Jeff Branch Editor-in-Chief: Jeff
More informationDESIGN TO BUILD = BUILD TO DESIGN
DESIGN TO BUILD = BUILD TO DESIGN The following represents five days of work from demolition through layout of new flooring and wall frame and cabinetry Paul C. King, RA Associate Professor Department
More informationCUSTOM SHUTTERS IN-A-BOX
CUSTOM SHUTTERS IN-A-BOX SHUTTER ASSEMBLE INSTRUCTIONS & INSTALLATION INSTRUCTIONS 1. Inspect the contents of your package. Do not discard the shutter packaging box until you have started painting your
More informationThe Ultimate Storage Cart Tutorial
The Ultimate Storage Cart Tutorial TOOLS Table saw (or circular saw and straight edge) (alternatively, a good hardware store could make these cuts for you) Router with 1/2 bit Straight edge Clamps Screwdriver
More informationMATERIALS: TOOLS: CUT LIST:
MATERIALS: TOOLS: (2) 2x2x8 Ft. Boards Tape Measure (2) 1x4x8 Ft. Boards Pencil (4) 1x2x8 Ft. Boards Carpenter s Square (1) 4x4 Ft. Sheet of ¾-Inch Plywood Drill with 5/16-inch Drill Bit (1) 1 ½-inch Thick
More informationCowper From Steve Wolverton on the T&TTT forum, Feb 2005 For Reference Only Do not use to build a trailer. Check on Teardrop and Tiny Travel Trailers
Cowper From Steve Wolverton on the T&TTT forum, Feb 2005 For Reference Only Do not use to build a trailer. Check on Teardrop and Tiny Travel Trailers for up to date building information; http://www.mikenchell.com/forums
More informationDress up your dining room with this Southern delicacy. that was used to serve drinks after a hunt. Breeches and jodhpurs are optional.
Dress up your dining room with this Southern delicacy that was used to serve drinks after a hunt. Breeches and jodhpurs are optional. Huntboard Classic Six-Legged My dad has been making this six-legged
More information