Wood Sawhorse. Description: Materials: Tools: Drawing/Photo: Name: Date:
|
|
- Annis Cook
- 6 years ago
- Views:
Transcription
1 Wood Sawhorse Name: Date: Description: The project is a wood sawhorse that can be used for workspace for future projects. It requires layout and wood working/construction skills. Materials: 4-1x6x30 DF (or equivalent) - Legs 2- ½ x 10 x 12 Plywood - End Gussets 1-2x6x30 DF Top /8 Drywall Screws Glue Sand Paper Stain or Other Finish Tools: Compound Miter Saw Cordless Hand Drill and Drill Bits #10 Countersink Drill Bit #2 Phillips Bit Driver and Bits Cordless Circular Saw Palm Sander Steel Tape Protractor Sliding T Bevel Framing Square Pencil Assorted Clamps Drawing/Photo: Revised: 6/27/2011 1
2 Directions: 1. Identify the materials and tools. 2. Review the plan. Select your lumber and determine the best layout. 3. Rip cut the 2 x 6 top piece so that both long edges are at a 15 o bevel. The edges should slope away from each other (not parallel). With the same side facing up, crosscut the ends of the 2 x 6 top so that the short edges are at a 15 o bevel (again, sloping away from each other), and the overall length is Cut the legs from 1 x 6 stock on the Compound Miter Saw set to the desired angles The ends of the legs are cut at a compound angle which means that you will cut through the wood with the saw set at two angles (15 bevel and 15 angle). Cut to the correct length (see plans). It is important that all 4 legs are the same. 5. Rip plywood to 10 (gusset height) on the table saw and layout the gusset angles and cut angles on the Compound Miter Saw. 6. Layout and countersink the screw holes as per the plans. 7. Attach the legs using glue and Drywall Screws. Use 3 screws per leg. Once all 4 legs are attached, place the sawhorse on a flat portion of the floor to check if the sawhorse rocks. 8. Layout and countersink the holes for the end gussets. 9. Attach to the legs on each end. Use 13 screws per end gusset. 10. Sand smooth. Finish with stain or paint if desired. Notes: Revised: 6/27/2011 2
3 Plans: Revised: 6/27/2011 3
4 Wood Sawhorse #2 Student Worksheet: Name: Date: Complete this worksheet prior to starting the project. 1. What angle do you set the compound miter saw to cut the legs for the sawhorse? 2. What is a compound angle? 3. How long should the legs be once they are cut? 4. What part of the sawhorse is assembled first? 5. What size and type of fastener is used? 6. How many screws are used in the whole project? 7. Why is it important that the 4 legs are the same? Grading Rubric: Criteria (tolerance 1/8") Possible Score Top Piece - Accurate Dimensions 5 Legs, All 4 are the same 5 Angles - Correct (15 ) 5 Fit up of the legs - Accurate and flush 5 Countersinks and screw installation on legs 5 End Gussets - Accurate and Flush 5 Countersinks and screw installation on Gussets 5 Cuts clean and square 5 Workmanship (fit, screws, finish) 5 TOTAL 45 Revised: 6/27/2011 4
5 Wood Sawhorse #2 Teaching Notes: Agricultural Standards Met: 4.0 Technology - Students know how to use contemporary and emerging technological resources in diverse and changing personal, community, and workplace environments: 4.6 Differentiate among, select, and apply appropriate tools and technology. 5.0 Problem Solving and Critical Thinking - Students understand how to create alternative solutions by using critical and creative thinking skills, such as logical reasoning, analytical thinking, and problem-solving techniques: 5.1 Apply appropriate problem-solving strategies and critical thinking skills to work-related issues and tasks. 5.3 Use critical thinking skills to make informed decisions and solve problems. 6.0 Health and Safety - Students understand health and safety policies, procedures, regulations, and practices, including the use of equipment and handling of hazardous materials: 6.1 Know policies, procedures, and regulations regarding health and safety in the workplace, including employers and employees responsibilities. 6.2 Understand critical elements of health and safety practices related to storing, cleaning, and maintaining tools, equipment, and supplies. 6.4 Maintain safe and healthful working conditions. 6.5 Use tools and machines safely and appropriately. 6.6 Know how to both prevent and respond to accidents in the agricultural industry. B1.0 Students understand personal and group safety: B1.1 Practice the rules for personal and group safety while working in an agricultural mechanics environment. B1.2 Know the relationship between accepted shop management procedures and a safe working environment. B2.0 Students understand the principles of basic woodworking: B2.3 Know how to identify, select, and implement basic fastening systems. B2.4 Complete a woodworking project, including interpreting a plan, developing a bill of materials and cutting list, selecting materials, shaping, joining, and finishing. Objectives: By successfully completing this project students will be able to: Read a plan to obtain critical dimensions Measure and layout a wood project Identify by name common woodworking tools Select and properly used hand and power tools used for wood work Cut and assemble wood components successfully Alternate Tools: A hand saw can be used to cut the wood to replace the compound miter saw and the circular saw. A band saw can replace the compound miter saw on some cuts. Revised: 6/27/2011 5
6 Safety Review: Use of the hand power drill. User of the compound miter saw. Use of the circular saw. Project Time: Demonstration: minutes Build: 3-5 hours Demonstration Notes: (Tips, methods to stage the project) 1. Begin by reviewing materials and tools used for the project. 2. Review the plan and show how the plan describes the project. 3. Demonstrate the proper use of compound miter saw and a circular saw. 4. Demonstrate how to measure and mark the cuts you need, especially the angles. 5. Demonstrate cutting the wood and accounting for the amount the saw takes out of the wood. 6. Demonstrate how to layout and install the legs. 7. Review hand power drill safety as you demonstrate drilling and countersinking the screw holes for the legs and gussets. 8. Remind students of workmanship. Final project should be clean and free of sharp edges. Bill of Materials (Excel, update with local prices) Projects: 20 Size Description Units Qty/Project Cost/Unit Order Amount 2 x 6 DF Top 10' Length 0.25 $ $ x 6 DF Legs (4) 10' Length 1 $ $ /2" Ext. Plywood - Gusset Sq Feet 2 $ $ /8" x 1/2" Drywall Screws 5lb Box 1 $ $ $ - 0 $ - 0 $ - Cost Per Project: $ TOTAL $ Project from: Dick Piersma Revised: 6/27/2011 6
Step Stool. Description: Materials: Tools: Directions: Name:
Step Stool Name: Description: This project provides students the opportunity to work on wood working skills. Use of dimensional lumber is good practice for construction projects. Cutting angles and notches
More informationRafter. Cut a rafter using appropriate construction tools and learn to use a framing square to layout a common rafter angle and length.
Rafter Name: Date: Description Cut a rafter using appropriate construction tools and learn to use a framing square to layout a common rafter angle and length. Materials: 2x4x Fir (36 ) Tools: Sliding T-bevel
More informationTool Tote Project. Tools:
Tool Tote Project Name: Date: Description: This project consists of building a small tool tote that is useful in the shop or garden. General skills used to build this project include drawing, measuring,
More informationPaper Towel Holder Project
Paper Towel Holder Project Name: Date: Description: Construction of the towel holder utilizes scrap lumber to make a useful project. Workmanship is a key part of the project. In Building this project you
More informationSaw Guide and Rafter Square
Saw Guide and Rafter Square Name: Description: The project is a tool for guiding a circular saw as well as a functional square and rafter layout tool. Useful cold metal skills are used to construct the
More informationWood Planter Box. Description: Materials: Procedure: Name: Date:
Wood Planter Box Name: Date: Description: Students will complete a wood working project by building a wood planter box. The planter box will be big enough to hold 4 4 square pots or can be filled with
More informationWoodworking Boot Jack
Woodworking Boot Jack Name: Date: Description: Students will create boot jacks from wood supplied by the shop. The proper tools used for this project will be listed and demonstrated for proper use by the
More informationWoodworking Clay Pot Hanger
Woodworking Clay Pot Hanger Name: Date: Description: A useful small project that demonstrates layout skills using a grid. Hanger holds a 6 clay pot.. Materials: 2 x 4 redwood or cedar 120 grit sandpaper
More informationSheet Metal Toolbox. Tools:
Sheet Metal Toolbox Name: Date: Description: 15 long sheet metal toolbox with wood ends and a dowel for handle. Useful for tools or supplies. Combines both beginning sheet metal skills and wood working..
More informationHose Hanger Cold Metal Work
Hose Hanger Cold Metal Work Name: Date: Description: A cold metal project that gives students practice sheering, bending, drilling, and fastening steel. The hose hanger can be used for proper storage of
More informationOxy-Fuel Cutting Skill Assignment
Oxy-Fuel Cutting Skill Assignment Name: Date: Description: This project will help you evaluate your Oxy-Fuel cutting skills. Knowledge of project layout and the ability to follow directions will be tested
More informationMeat Hook. Tools: Materials: Directions: Name: 1/4 round cold rolled steel 20 long 1 wooden dowel 5 long Epoxy Wood Stain Sand Paper Emery Cloth
Meat Hook Name: Description: This project allows students to use hot and cold metal working skills and wood working skills to construct a meat hook. Hot metal working skills are also useful for making
More informationBirdhouse. Materials: Tools: Procedure: Name: Date: Description:
Birdhouse Name: Date: Description: Students will build a traditional cedar birdhouse using a layout, wood, hammer, glue, and wood dowel. Agriculture mechanic shop tools such as a miter saw, table saw,
More informationBattery Terminal Puller
Battery Terminal Puller Name: Date: Description: Students will be able to construct a Battery Terminal Puller. Students will focus on using cold metal skills, layout skills, and forming the metal into
More informationFence Wire Bender. Description: Tools: Materials: Procedure: Notes: Name: Date:
Fence Wire Bender Name: Date: Description: Small tool used to bend wire around another piece of wire for a fence. Processes used to build a wire bender are drilling, cutting and bending. Practices hot
More informationBoot Scraper. Description: Materials: Tools: Procedure: Name: Date:
Boot Scraper Name: Date: Description: This boot scraper will be constructed out of mild steel. This project will utilize cold metal cutting with the hydraulic ironworker. Shielded Metal Arc welding will
More informationNote Pad Holder. Tools:
Note Pad Holder Name: Date: Description: The note pad holder is a cold metal project that involves layout skills and sheet metal fabrication skills Materials: 3 1/8 x ¼ Aluminum Pop Rivet 18 ga. Galvanized
More information1 ¼-inch Pocket Screws Brad Nailer or Hammer 1 ¼-inch Brad Nails Clamps
MATERIALS: TOOLS: (4) 2 x 6 x 8 Ft. Boards Tape Measure (2) 2 x 4 x 8 Ft. Boards Carpenter s Square (7) 1 x 4 x 8 Ft. Boards Pencil (2) 1 x 3 x 8 Ft. Boards Drill (1) Half Sheet of ¾-inch Thick Plywood
More informationSimple Woodworking: Outdoor Pitch Chair
Parts Lumber Front Front Leg Front Leg Drill three pocket holes on each end of the Front - one centered and two 3/4" from each side. Cut a 15-degree miter on one end of the Front Legs. It will be easier
More informationChief s Shop: Simple Woodworking Bench
Chief s Shop: Simple Woodworking Bench Be sure to read the instructions and review the illustrations and accompanying video for this project BEFORE you start. Follow ALL SAFETY GUIDELINES AND RECOMMENDATIONS
More informationThis indicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
S i m p le Woodworking: What You'll Need v lumber 2-1 x 12 x 6 hardware/supplies (availability will vary) 1 1/4" pocket hole screws #18 x 1 1/2 brads or pocket hole plugs 12-inch continuous hinge magnetic
More informationDIY Wine Storage Cabinet
DIY Wine Storage Cabinet ADDICTED2DIY.COM *Before beginning this project, please read through all of the plans and the blog post. When building this project, be sure to measure your wood and cut to fit.
More informationGarden Trellis. This project was developed from an example provided by Dick Piersma, Hilmar High School.
Garden Trellis This project was developed from an example provided by Dick Piersma, Hilmar High School. Description: A sturdy trellis made from part of a hog panel. Dimensions can be easily altered to
More informationDIY X Panel Side Table
DIY X Panel Side Table *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever using power tools
More informationWOOD MANUFACTURING 30
WOOD MANUFACTURING 30 Description This course is designed to introduce to the student the processes and techniques of leg and rail construction. Student skills will be developed through tool and machine
More informationMyOutdoorPlans.com. By Julian King [2X4 GARDEN BENCH]
MyOutdoorPlans.com By Julian King [2X4 GARDEN BENCH] CUT LIST A 2 pieces of 2 4 lumber 24 long, 2 pieces 32 1/2 long LEGS B 2 pieces of 2 4 lumber 45 long, 2 pieces 15 1/2 long, 1 piece 12 1/2 long SEAT
More informationindicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
f a r m h o u s e d i ni ng c h a i r What You'll Need lumber Beginner 1-1 x2x4 1-1 x2x8 3-2x3x8 1-2x4x8 1-3/4 x 2 x 4 sheet of plywood (availability will vary) Intermediate Intermediate Beginner About
More informationWhat we ll be learning today
Set Construction What we ll be learning today The use, construction of, and terminology of typical scenic elements The lumber, tools, and hardware used to build these scenic elements Stock Scenery Stock
More informationConstruction III Curriculum Maps
Curriculum Maps Unit 1: Shop Safety Unit 2: Shop Equipment and Tool Review Unit 3: Project I Unit 4: Building Plans and Materials Unit 5: Footings and Foundations Unit 6: Floor Framing Unit 7: Wall Framing
More informationDIY Outdoor Console Table Addicted2DIY.com
DIY Outdoor Console Table Addicted2DIY.com *Before beginning this project, please read through all of the plans. Always use safety precautions whenever using power tools and follow the manufacturer s suggested
More informationThis indicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
S i m p le Woodworking: Bath Side Table What You'll Need v lumber 4-1- x 36-inch square dowels 1-1 x8x8 1-3/4-inch x 2- x 4-foot sheet of plywood hardware/supplies 1 1/4" pocket hole screws #18 x 1 1/2
More informationindicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
ho m e o f f i c e de s k What You'll Need lumber 1-1 x2x4 4-1 x2x8 8-1 x3x8 1-3/4 x 4 x 8 sheet of plywood hardware/supplies (availability will vary) 1 1/4" brads Kreg 1 1/4" pocket hole screws wood glue
More informationWhat we ll be learning today
Set Construction What we ll be learning today The use, construction of, and terminology of typical scenic elements The lumber, tools, and hardware used to build these scenic elements How to build these
More informationReceiver Hitch and Pin
Receiver Hitch and Pin Description: The hitch is used with a standard 2 receiver hitch commonly found on trucks and SUVs. It can be fitted with any size ball. It may be mounted up or down depending on
More informationWooden Christmas Tree
Wooden Christmas Tree Created by DIY hacker, woodworker and teacher, Kerryn Carter of Toolschool, take your Christmas tree to a whole new level, with this wooden Christmas Tree project. PROJECT INFORMATION
More informationindicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
What You'll Need lumber 1-1 x3x4 1-1 x3x8 2-1 x6x8 1-1 x 10 x 4 hardware/supplies (availability will vary) 2" wood screws 1 1/4" pocket hole screws wood glue paint/stain tools table saw miter saw jigsaw
More informationindicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
f a r m h o u s e d i ni ng b e nc h What You'll Need lumber 6-2x3x8 6-1 x6x8 (availability will vary) Intermediate or equivalent 8/4 lumber planed to 1 1/2" for the 2x hardware/supplies 1 1/4" pocket
More informationKreg Tool Co. All Rights Reserved.
Version 1 p. 1 Materials: Lumber: Qty: Board 2 2x2s 3 ft. long 2 1x2s 8 ft. long 2 1x3s 8 ft. long 6 1x6s 10 ft. long INSTRUCTIONS: Supplies: 1 1 / 4" Kreg Screws (coarse thread for softwoods, fine thread
More informationThe WoodWorker s Edge
The WoodWorker s Edge Draw-leaf Game Table 1. 2. Layout the area for the tenons. The tenons are 3/8 thick x 4-1/2 long x 1-1/4 deep and offset to the inside. Create the tenons using the step method to
More informationDresser. Materials & Tools FEATURING FORMALDEHYDE-FREE TECHNOLOGY. Free Plans to build a Dresser
Free Plans to build a Dresser Materials & Tools Materials: 1-1/4 pocket hole screws 1-1/4 brad nails 3 sets of 18 drawer slides Drawer pulls Edge banding, optional Wood glue Sandpaper (100, 150, 220 grits)
More informationThis indicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
S i m p le Woodworking: What You'll Need v lumber 1-2x4x8 9-2 x 4 x 10 1-2x6x8 2-2 x 6 x 10 1-2 x 10 x 8 2-4x4x8 hardware/supplies (availability will vary) 2 1/2" pocket hole screws 2 1/2" deck screws
More informationHow to Build a DIY Extra Long Wood Bench
How to Build a DIY Extra Long Wood Bench Free woodworking plans for building a large, extra-long wood bench. This bench measures 9 in length and is designed to match the DIY Large Outdoor Dining Table,
More information(1) 2x4 Ft. Sheet of ¼-inch Plywood. 1 ¼-inch Wood Screws. 1 ¼-inch Brad Nails ¾-inch Brad Nails Wood Glue CUT LIST:
MATERIALS: (5) 1x3x8 Ft. Boards (3) 2x4x8 Ft. Boards (10) 1x4x8 Ft. Boards (1) 1x2x10 Ft. Board (1) 2x2x4 Ft. Board (2) 1x6x8 Ft. Boards (1) 4x8 Ft. Sheet of ¾-inch Plywood (1) 2x4 Ft. Sheet of ¼-inch
More informationindicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
p a r t o ne : B a s e What You'll Need lumber 2-2x4x8 4-2x6x8 1-3/4-inch x 4- x 8-foot sheet of plywood hardware/supplies (availability will vary) 2 1/2" pocket hole screws 1 1/4" pocket hole screws 1
More informationPRO CYCTM PRO CYC, INC. SYSTEM 1.5 FS
ASSEMBLY INSTRUCTIONS Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship your cyc, so please take
More informationWoodworking. EXAM INFORMATION Items. Points. Prerequisites. Grade Level. Course Length EXAM BLUEPRINT. Career Cluster. Performance Standards
EXAM INFORMATION Items 66 Points 66 Prerequisites NONE Grade Level 10-12 Course Length ONE SEMESTER Career Cluster ARCHITECTURE AND CONSTRUCTION MANUFACTURING Performance Standards INCLUDED Certificate
More informationPage 1 C & C 30 MK II. Building the bulkhead Liquor Cabinet. 1. This package contains pages of instructions and sketches.
Page 1 C & C 30 MK II Building the bulkhead Liquor Cabinet 1. This package contains pages of instructions and sketches. 2. Woodworking skills and equipment are essential to make the 33 pieces and assemble
More informationCabinetmaking & Millwork CIP Task Grid
1 Secondary Task List 100 FOLLOW RULES FOR WORKING IN THE CABINETMAKING LAB. 101 Review and discuss school rules. 102 Review and demonstrate knowledge of cabinetmaking lab rules. 103 Complete all theory
More informationProject 12231EZ: Country Curio Clock
Project 12231EZ: Country Curio Clock This good-looking clock not only reminds you of the time, it also provides a couple of shelves to display favorite curios. No fancy joinery is needed here, just butt
More informationPorch. Swing. Build A. farmstead: project
farmstead: project Porch Build A Swing Instructions Cut all parts to fit as you assemble the project and use the Parts List and Cutting Diagram as a guide for dimensions. When gluing pieces together, you
More information(28) 2 x 4 x 8 Ft. Boards Tape Measure (9) 2 x 6 x 8 Ft. Boards Pencil (6) 2 x 2 x 8 Ft. Boards Carpenter s Square (9) 1 x 3 x 8 Ft.
MATERIALS: TOOLS: (28) 2 x 4 x 8 Ft. Boards Tape Measure (9) 2 x 6 x 8 Ft. Boards Pencil (6) 2 x 2 x 8 Ft. Boards Carpenter s Square (9) 1 x 3 x 8 Ft. Boards Drill 2 ½-inch Pocket Screws Circular Saw 2
More informationProject Skill Level: INTERMEDIATE Plywood Used: CANPLY EXTERIOR Good Two Sides (G2S) or precision sanded Aspen
Project Skill Level: INTERMEDIATE Plywood Used: CANPLY EXTERIOR Good Two Sides (G2S) or precision sanded Aspen MATERIALS LIST: (1) ¾" x 4 ft x 8 ft plywood panel (20) #8 x 2" Robertson or Phillips wood
More informationFortress Al Posts must always be secured to the deck framing. Fortress Al Posts should never be attached to only the deck boards.
Installation Instructions for Fortress Railing Traditional Panels with s and Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain all required building
More informationElectrical Wiring Projects
Electrical Wiring Projects Name: Date: Description: Students will learn how to properly install and wire using common industrial devices on an Electrical Board. Students will practice using common electrical
More informationThis indicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
S i m p le Woodworking: R u s t i c s i d e t ab l e What You'll Need v lumber 4-1 x 6 x 6 or reclaimed 1 x 6 x 6 fence pickets hardware/supplies (availability will vary) 1 1/4" pocket hole screws 1 1/4"
More informationmake something original Mobile Workstand Shelf support (2) Caster extension (2) Leveling feet (4) Rigid caster (2)
Mobile Workstand Panel (2) Leg (4) Long frame member (2) Crossmember (6) Shelf (1) Shelf support (2) Caster extension (2) Leveling feet (4) Rigid caster (2) THIS IS NOT THE COMPLETE PLAN: it is merely
More informationCedar 2-Drawer Desktop Storage Cube
Cedar 2-Drawer Desktop Storage Cube 5 ½ Dimensions 5 ½ 5 ½ 2 2 1 7/8 4 ¼ 4 ½ Author s Notes: Build a Cedar 2-Drawer Desktop Storage Cube from just 1 cedar fence picket. No angles, special cuts or rips
More informationPLANS BY KELLEY FARMHOUSE DESIGNS LOFTED DORM ROOM BED
PLANS BY KELLEY FARMHOUSE DESIGNS LOFTED DORM ROOM BED DIMENSIONS: 82" X 70" X 45" DIFFICULTY LEVEL: INTERMEDIATE TOOLS REQUIRED ONE+ Circular Saw ONE+ AirStrike 16GA Finish Nailer ONE+ Impact Driver ONE+
More informationDEPARTMENT: Applied Technology. COURSE: Woodworking I. Marking Period 1 or 3. Special Safety 2 Introduction to Measurement, Problem Solving,
DEPARTMENT: Applied Technology COURSE: Woodworking I Week Marking Period 1 or 3 1 Course Intro, General Safety, Hand Tools and Special Safety 2 Introduction to Measurement, Problem Solving, Design 3 Design
More informationCourse Outline CIAO 123 Cleveland Street Orange, NJ 07050
Course Outline CIAO 123 Cleveland Street Orange, NJ 07050 Teacher: Mr. Daniel Email: danielra@orange.k12.nj.us Phone: 973-673-0746 Course Syllabus Woodworking I Full Year Course COURSE DESCRIPTION: Woodshop
More informationLocker Pedestal Installation Instructions
Locker Pedestal Installation Instructions LK-PED-INST-0314r1 Parts List Single Pedestal Back to Back Pedestal Horizontal Support Tube TS-169 Post Flange TS-190 Post Cap Fasteners Provided: #8 x ¾ round
More informationCabinetmaking & Millwork CIP Task Grid
1 Secondary Task List 100 DEMONSTRATE PERSONAL SAFETY. 101 Demonstrate knowledge of general safety rules for working in the cabinetmaking lab. 102 Identify cabinetmaking lab tools and equipment. 103 State
More informationindicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
What You'll Need lumber 1-1 x 3 x 6 2-1 x3x8 1-1 x8x6 1-1 x 12 x 6 2-2 x 2 x 8* (availability will vary) *if2x2s ofthis size are not available, laminated two 1x2s to create 2x2s) hardware/supplies Kreg
More informationCUSTOM SHUTTERS IN-A-BOX
CUSTOM SHUTTERS IN-A-BOX SHUTTER ASSEMBLE INSTRUCTIONS & INSTALLATION INSTRUCTIONS 1. Inspect the contents of your package. Do not discard the shutter packaging box until you have started painting your
More informationStudy Guide: Agriscience Technology Mechanics
Study Guide: Agriscience Technology Mechanics Matching - Safety Colors: 1. Danger A. Yellow 2. Information B. Green 3. Safety C. Red 4. Warning D. Blue 5. Caution E. Orange Matching - Tool Categories 6.
More informationSkillsUSA Wisconsin CABINETMAKING
SkillsUSA Wisconsin CABINETMAKING The following rules are for the Wisconsin state contest only. Students/Teams that qualify for the national contest need to adhere to the rules and guidelines for that
More informationAgricultural Mechanics and Technology Power Tool Safety Rules
Agricultural Mechanics and Technology Power Tool Safety Rules Name: BAND SAW Use: Cutting curves, circles and irregular shapes. 1. Use clean SHARP blades. 2. The teeth should always point DOWN. 3. Adjust
More informationPRO CYC PRO CYC, INC. SYSTEM SUPER 3EZ
ASSEMBLY INSTRUCTIONS SYSTEM SUPER 3 EZ Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship your
More informationWant to reach a captive woodworking and crafting audience?
Want to reach a captive woodworking and crafting audience? Then be a sponsor of Chief's Shop Plan of the Week Contact Chris Hill for more details chief@chiefs-shop.com 205-432-801 3 S i m p le Woodworking:
More informationCopyright 2010 Springbok Publishing All Rights Reserved- Page 1
Copyright 2010 Springbok Publishing All Rights Reserved- www.woodensaddlerackplans.com Page 1 Legal Information All contents copyright 2010 by Springbok Publishing. All rights reserved. No part of this
More informationTrestle Table and Benches Materials List
Project 18444EZ: Trestle Table and Benches In the early days of our country, trestle tables were popular because they could easily be disassembled and moved out of the way when not in use no small advantage
More informationGrade 11 Woods Lift Lid Coffee Table. Based on Under the big Top from Popular Mechanics Website
Grade 11 Woods Lift Lid Coffee Table Based on Under the big Top from Popular Mechanics Website TABLE TOP 1. Select enough lumber to construct a top that is between 22 ½ and 24 wide after jointing. Ensure
More informationAmerica s leading woodworking authority To download these plans, you will need Adobe Reader installed on your computer. If you want to get a free copy, visit: http://adobe.com/ reader. Having trouble downloading
More informationPremium Single Dutch Doors Assembly & Installation Instructions
Premium Single Dutch Doors Assembly & Installation Instructions Premium Single Dutch Door Instructions General Notes; -Read the entire instructions before you begin. -Wear appropriate safety gear when
More informationBuilding Sturdy Sawhorses
Save up to 52%! Give a Gift How-To Building Sturdy Sawhorses by Patrick McCombe Share this with friends! Email Twitter Facebook Pinterest I once had a coworker who described his favorite sawhorses as Clydesdales.
More informationMATERIALS: TOOLS: CUT LIST:
MATERIALS: (3) 4x4x8 Ft. Boards (8) 2x4x8 Ft. Boards 2 ½-inch Pocket Screws 2 ½-inch Wood Screws 1-inch Wood Screws (16) Figure 8 Tabletop Fasteners Wood Glue Wood Filler TOOLS: Tape Measure Pencil Carpenter
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 2
Kentucky 4H Wood Science Plans Notebook Plans Level 2 MATERIALS NEEDED: JEWELRY BOX WS201 1 piece wood 1/4" x 4 x 4 1/2" (bottom) 1 piece wood 1/4" x 4 1/2" x 5 (top) 2 pieces wood 1/4" x 2 x 5 (front
More informationWorkstation. Multipurpose. Shop Project
Shop Project Multipurpose Workstation Rock-solid, practical, and inexpensive it s tough to beat this versatile workstation that you can make from one sheet of plywood.. I don t think a woodworker can ever
More informationWAYNESBORO AREA SCHOOL DISTRICT CURRICULUM MATERIALS AND MANUFACTURING I
UNIT: Workplace Safety NO. OF DAYS: 2 KEY LEARNING(S): Appropriate conduct while present in an industrial environment Accidents are preventable in an industrial setting UNIT : Why is it important to be
More informationHow to build a Ram for Challenge E: Twist-O-Rama
How to build a Ram for Challenge E: Twist-O-Rama Notes The Ram is like the Structure Tester it is not Interference for a Team Manager or other non-team members to build it. Construction time is approximately
More information2. Sanding the Modules Sand the entire surface of each cyc module with 60-grit sandpaper. This will provide for better paint adhesion.
ASSEMBLY INSTRUCTIONS SYSTEM 4 BI (Built-In) Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship
More informationCopyright 1998 KDE Technologies
Modular Computer Corner Desk Unit Copyright 1998 KDE Technologies http://members.tripod.com/~kdetech/ 1. Introduction 2. Plans Sheet one - Isometric Sheet two - Top Detail / Corner Unit Sheet three - Leg
More informationCopyrighted Material Page 1
Compare to: Pottery Barn Teen Storage Bed System Skill Level: Beginner Working with the rest of the components in the Storage Bed Collection, the Small Hutch fits on top of the Storage Headboard and will
More informationEND FRAMES. End frames built using pressure treated 2x4 (1 1/2" x 3 1/2") 36" 34" 7/16" pilot hole. 5 1/2" x 1/2" lag bolt 8" wheel 23"
END FRAMES End frames built using pressure treated 2x4 (1 1/2" x 3 1/2") 23" 17 1/2" (B) (B) Measure from the bottom of your stone to 1" below the lip to get your measurement. 17 1/2"(B) 36" 34" 1/2" flat
More informationU. M. ARMY Texas Conference. Wheel Chair Ramp Manual
U. M. ARMY Texas Conference Wheel Chair Ramp Manual June 2014 U. M. ARMY Texas Conference Building & Repair Tips Wheelchair Ramps Complete a site survey to determine the design and layout of the ramp.
More informationPRO CYC PRO CYC, INC. SYSTEM SUPER 1.5 EZ
ASSEMBLY INSTRUCTIONS SYSTEM SUPER 1.5 EZ Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship your
More informationBrookfield Storage Bed Frame. Copyrighted Material. Page 1
Compare to: Pottery Barn Kids Brookfield Storage Bed Frame Skill Level: Intermediate Brookfield Storage Bed Frame Matching the Brookstone Headboard, the storage bed takes advantage of ALL the space under
More informationINSTALLATION INSTRUCTIONS MILLENNIUM DECKING Before Installing Millennium Decking, please read these instructions in their entirety.
INSTALLATION INSTRUCTIONS MILLENNIUM DECKING Before Installing Millennium Decking, please read these instructions in their entirety. Safety PRE-INSTALLATION Compliance with all applicable local, state
More informationPRO CYC PRO CYC, INC. SYSTEM SUPER 1.5QS
Assembly Instructions System Super 1.5QS Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship your
More information2. Sanding the Modules Sand the entire surface of each cyc module with 60-grit sandpaper. This will provide for better paint adhesion.
ASSEMBLY INSTRUCTIONS SYSTEM SUPER 2.5 EZ Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship your
More informationPerkins Statewide Articulation Agreement. Documentation item: Secondary Competency Task List Coversheet
Perkins Statewide Articulation Agreement Documentation item: Secondary Task List Coversheet The Secondary School agrees to: A. Implement the approved PDE Program(s) of Study. B. Provide assessment of student
More informationTools: Drill/Driver Kreg Jig Miter Saw Jigsaw Circular Saw Adjustable Square Tape Measure Veneer Trimmer Sandpaper and Sander
R PROJECT PLANS DROP-FRONT DESK Create a workspace almost anywhere with this drop-front desk. Mounted to a wall, it doesn t take up any floor space, which means you can hang it wherever you need to work.
More informationUsing the star template provided, trace out half the star shape on the pegboard sheet. Flip template over and trace out other side of star.
Shining Star PROJECT INFORMATION Created by DIY hacker, woodworker and teacher, Kerryn Carter of Toolschool, brighten up your Christmas with this shining Star, complete with LED lights for extra twinkle.
More informationDIY RUSTIC HALL TREE
DIY RUSTIC HALL TREE *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever using power tools
More informationWOOD TOY NEWS. July 23, 2013 Tuesday
WOOD TOY NEWS Make your own perfect turntable for spray painting toys with these useful tips. And it s fast, fun and easy to build! by Imants Udris Watch the video on our website at : http://www.toymakingplans.com/website/how-to/
More informationDECKING INSTALLATION GUIDE
STAIR TREAD INSTALLATION GUIDE Step 7: Install the Remaining Treads Repeat steps 2 to 6 for the remaining stair treads. Step 8: Install the Fascia 1. Measure the riser height. 2. Rip the fascia to the
More informationBuild It: The Most Amazing Cooler Bench Ever
Build It: The Most Amazing Cooler Bench Ever wooditsreal.com/2017/04/28/build-it-cooler-bench-free-plans/ A bench. A cooler. Put them together and what do you get? The most amazing Cooler Bench you ve
More informationProject 17884EZ: Shaker End Table
Project 17884EZ: Shaker End Table With its clean, simple lines, this piece is unmistakably Shaker style. Ours is made from cherry, a wood commonly used by Shaker craftsman, but we ve also seen this piece
More informationPatio Table. Page 1 of 16
Patio Table www.andrewharriswoodwork.com Page 1 of 16 Introduction This plan makes a table that is unit which is 95 ½ inches long and 49 inches wide. The distance from the underside of the top edging to
More informationEasy Five Cube Tower Bookshelf. Copyrighted Material. Page 1
Compare to: Land of Nod Cube Collection, 5 Cube Tower Bookshelf Skill Level: Beginner Easy Five Cube Tower Bookshelf This fully framed five cube tower can hold everything from towels to boots to books
More information