Absco EZISLIM Shed Model: 08151F

Size: px

Start display at page:

Download "Absco EZISLIM Shed Model: 08151F"

Melissa Ellis
5 years ago
Views:

1 FRONT: 0.78m SIDE: 1.52m HEIGHT: 1.80m CONCRETE SLAB 1620mm 880mm WHEN LAYING YOUR CONCRETE SLAB, CHAMFER THE 50mm EDGES DOWNWARDS BY 10mm. 50mm 10mm 50mm THIS WILL ENSURE THAT WATER RUN OFF IS KEPT CLEAR FROM YOUR SHED We thank you for choosng an Australan Made Shed. For further assstance please vst our detaled nstructonal vdeo lbrary at At ABSCO Industres we are always lookng to be number ONE, so please let us know what you thnk of our nstructons. Feedback makes us better. PAGE 1

GENERAL INSTRUCTIONS Before commencng any

to gan a thorough understandng of assembly

Unpack the carton and carefully dentfy and

descrbed and llustrated on pages three and four.

Anchor sets are not suppled as standard tems

It s advsable to wear gloves when handlng these

2 GENERAL INSTRUCTIONS Before commencng any assembly, read through these nstructons n detal to gan a thorough understandng of assembly methods and assocated detals. Unpack the carton and carefully dentfy and check off all the parts aganst the parts descrbed and llustrated on pages three and four. SITE PREPARATION The ste for the shed must be level. It s recommended that the shed be set on a 100mm concrete slab and anchored down approprately (refer page 16 for detals). Anchor sets are not suppled as standard tems wth ths product. TOOLS REQUIRED 3mm 4mm A NOTE ON SAFETY OPTIONAL Some parts may have sharp edges. It s advsable to wear gloves when handlng these tems and safety glasses f drllng holes. Sensble shoes are hghly recommended. Do not erect your shed n wndy condtons, ensure that the shed s securely anchored to a sold foundaton mmedately after constructon s completed. It s hghly recommended to erect the shed wth two or more people. PAGE 2

3 COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK 2 STEEL SHEET 1785mm X 773mm 30A 2 CHANNEL L = 1513mm 81E 2 STEEL SHEET 1785mm X 773mm 31A 1 CHANNEL L = 720mm 54G 1 STEEL SHEET 1592mm X 773mm 43A 2 CHANNEL L = 773mm 81J 1 STEEL SHEET 1785mm X 773mm 30F 2 CHANNEL L = 1785mm 80A 1 DOOR SHEET 1725mm X 711mm 37A 1 CHANNEL L = 1725mm 58B 2 CHANNEL L = 766mm 54H 2 CHANNEL L = 712mm 58M 2 CHANNEL L = 773mm 54F 1 JAMB L= 1785mm 89A 2 CHANNEL L = 1513mm 61A 1 JAMB L= 1785mm 89B PAGE 3

4 COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK 1 91D 2 88A JAMB L= 720mm LIP TRIM L= 1592mm 1 58A DOOR TRIM SIDE CHANNEL WITH HINGES FITTED L = 1725mm 2 91E JAMB L= 1080mm CONTENTS OF FITTINGS PACKET 120 SELF TAPPING SCREWS 10mm 1 DOOR PADBOLT 22A 6 4mm CSK SCREW & NUT SECURE HINGES TO DOOR 1 DOOR PADBOLT HASP 12 SELF TAPPING SCREWS 20mm REFER TO PAGE mm POP RIVETS SECURE HINGES TO DOOR (ALTERNATIVE FIXING METHOD) 1 ASSEMBLY INSTRUCTIONS 1 DOOR STRAP L: 165mm 12A PAGE 4

5 VIEW OF ROOF COMPONENTS 81J 88A 43A 88A 81J PAGE 5 NO.

6 54F 61A Absco EZISLIM Shed 61A 30F 30A 80A 30A 31A 54H 31A 91D 89A 58M 54F 54G 91E 37A 58A 81E 81E 80A 89B 54H VIEW OF WALL COMPONENTS 58B 58M PAGE 6

ABSCO ASSEMBLY INTRODUCTION The snap-tte assembly system locks most permeter channels to all roof and wall sheets wthout the need for tools and fasteners.

7 ABSCO ASSEMBLY INTRODUCTION The snap-tte assembly system locks most permeter channels to all roof and wall sheets wthout the need for tools and fasteners. The front door frame and door assembly wll requre 3mm holes to be drlled where necessary. To pre-assemble the four wall panels and two roof panels, the permeter channels are secured to the top and bottom of each panel usng the snaptte system, as detaled on the followng pages wherever you see the symbol. HIGH SIDE PUSH HIGH SIDE HIGH SIDE HIGH SIDE PUSH After jonng sheets together, poston channel over one end of the sheets, gently tappng t over the snaptte lugs, workng along the sheets to the other end. PUSH Poston sheets on tmbers, trestles or partly over edge of concrete slab. FASTENING SYMBOLS HIGH SIDE Each permeter channel must fnsh flush wth the edges of the sheets. the snap-tte system allows adjustment for ths process by smply tappng the channel along the sheets untl each end s neatly flush. Jon components together wth one screw at ths locaton only, as some channel sectons have extra holes that are not requred for ths model of garden shed 3mm POP RIVETS 4mm NUT & BOLT SET Do not jon components together at ths locaton yet, as the screw may obstruct further assembly of other components PAGE 7

8 SIDE PANEL ASSEMBLY LEFT SIDE PANEL 80A 31A 30A 61A 81E PAGE 8

9 SIDE PANEL ASSEMBLY RIGHT SIDE PANEL 30A 31A 80A 61A 81E PAGE 9

10 REAR PANEL ASSEMBLY 30F 54F 54F PAGE 10

11 ROOF PANEL ASSEMBLY 43A 81J 88A 88A 81J PAGE 11

12 FRONT FRAME ASSEMBLY 54H 89A TOP 91D 89B 54G BOTTOM 54H PAGE 12

13 DOOR PANEL ASSEMBLY NOTE: THIS SHEET (37A) IS 711mm WIDE BY 1725mm HIGH 58M NOTE: USE THE PRE-PUNCHED COMPONENTS (58A, 58B, 12A) AS TEMPLATES FOR DRILLING 3mm HOLES INTO THE SHEET (37A) 58A 58B 37A NARROW PAN THIS SIDE 12A 715mm MAXIMUM WIDTH 58M 20mm FLANGE 37A 15mm FLANGE PAGE 13

14 FRONT PANEL AND DOOR CONNECTION ASSEMBLY PHOTOS CORNER DOOR JAMB ASSEMBLY DOOR CONNECTION & JAMB ASSEMBLY PADBOLT & HASP CONNECTION PADBOLT TO DOOR CONNECTION DOOR BRACE CONNECTION NOTE: PLEASE REFER TO THE FOLLOWING PAGES FOR FURTHER DETAIL PAGE 14

15 PANEL CONSTRUCTION NOTE: Take care to ensure that both front and rear wall panels are not postoned upsde down. The top channel of each panel s pre-punched for attachng roof sheets. The base channels are not pre-punched. 31A 80A 89B CONNECT BOTH DOOR MULLION SECTIONS WITH SIX 20mm SCREWS EACH SIDE. REMOVE AND REPLACE CORNER SCREWS ONE AT A TIME DURING CONSTRUCTION SIDE WALL PANEL CHANNELS FIT INTO THE NOTCHED FRONT AND REAR WALL PANEL CHANNELS PAGE 15

16 ROOF CONSTRUCTION AND ANCHORING OF SHED NOTE: IT IS IMPORTANT TO COMPLETE THE STEPS ON THIS PAGE BEFORE PROGRESSING ANY FURTHER ANCHORING OF SHED LOCATION OF 8 CONCRETE ANCHORS - EACH ANCHOR CONSISTS OF ONE NUT, BOLT, DYNABOLT AND STEEL ANGLE - DRILL A 10mm HOLE INTO THE WALL SHEET BOLT & NUT STEEL ANGLE WALL SHEET SLAB - DRILL A 10mm HOLE INTO THE CONCRETE DYNABOLT PAGE 16

17 DOOR PANEL ASSEMBLY 91E 37A 91E USING THE JAMBS AS TEMPLATES, DRILL 3mm HOLES INTO THE SHEET AND SECURE WITH SCREWS 37A PAGE 17

18 FINAL CONSTRUCTION CONNECT DOOR TO FRONT FRAME NOTE: NUTS AND BOLTS (SUPPLIED) MAY BE USED INSTEAD OF POP RIVETS (SUPPLIED) BY SIMPLY ENLARGING THE HINGE HOLE SETS IN THE JAMB USING A 4MM DRILL BIT NOTE: The two holes requred to connect the padbolt hasp for each door have not been pre-punched, to allow for proper algnment. Poston the hasp centrally over the padbolt shaft, and drll 3mm holes and secure wth screws. PAGE 18

Absco Space Saver Shed Assembly Instructions Model: 23081SK

Absco Space Saver Shed Assembly Instructions Model: 23081SK Assembly Instructons Model: 2308SK FRONT BASE LENGTH: 2.26m SIDE BASE LENGTH: 0.78m FRONT WALL HEIGHT:.80m REAR WALL HEIGHT:.95m CONCRETE SLAB 880mm 2360mm WHEN LAYING YOUR CONCRETE SLAB, CHAMFER THE 50mm