Absco Space Saver Shed Assembly Instructions Model: 15081S

Transcription

1 Assembly Instructions FRONT BASE LENGTH:.5m SIDE BASE LENGTH: 0.78m FRONT WALL HEIGHT:.8m REAR WALL HEIGHT:.95m CONCRETE SLAB 60mm 880mm WHEN LAYING YOUR CONCRETE SLAB, CHAMFER THE 50mm EDGES DOWNWARDS BY 0mm. 50mm 0mm 50mm THIS WILL ENSURE THAT WATER RUN OFF IS KEPT CLEAR FROM YOUR SHED We thank you for choosing an Australian Made Shed. For further assistance please visit our detailed instructional video library at At ABSCO Industries we are always looking to be number ONE, so please let us know what you think of our instructions. Feedback makes us better. PAGE

2 GENERAL INSTRUCTIONS Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details. Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on pages three and four. SITE PREPARATION The site for the shed must be level. It is recommended that the shed be set on a 00mm concrete slab and anchored down appropriately (refer page 5 for details). Anchor sets are not supplied as standard items with this product. TOOLS REQUIRED 3mm 4mm A NOTE ON SAFETY OPTIONAL Some parts may have sharp edges. It is advisable to wear gloves when handling these items and safety glasses if drilling holes. Sensible shoes are highly recommended. Do not erect your shed in windy conditions, ensure that the shed is securely anchored to a solid foundation immediately after construction is completed. It is highly recommended to erect the shed with two or more people. PAGE

3 COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK STEEL SHEET 95 X 773mm 43B L = 53mm 53C STEEL SHEET 95mm X 773mm X4L L = 53mm 8F STEEL SHEET 95mm X 773mm XR L = 53mm 8E STEEL SHEET 865mm X 773mm 43D L = 785mm 80A STEEL SHEET 785mm X 7mm 34A L = 786mm 6B STEEL SHEET 75mm X 773mm B L = 773mm 8J 53A L = 53mm L = 783mm 79C 53B L = 53mm PAGE 3

4 COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK WITH HINGES L = 75mm 58A JAMB L= 785mm 89B L = 75mm 58B JAMB L= 783mm 90C L = 773mm 58C JAMB L= 0mm 9A JAMB L= 785mm 89A LIP TRIM L= 865mm 88B CONTENTS OF FITTINGS PACKET 0 SELF TAPPING SCREWS (0mm) DOOR PADBOLT A 6 4mm CSK SCREW & NUT SECURE HINGES TO DOOR DOOR PADBOLT HASP ASSEMBLY INSTRUCTIONS 6 3mm POP RIVETS SECURE HINGES TO DOOR (ALTERNATIVE FIXING METHOD) 6 SELF TAPPING SCREWS (0mm) DOOR STRAP L: 65mm A PAGE 4

5 VIEW OF ROOF COMPONENTS PAGE 5

6 VIEW OF WALL COMPONENTS PAGE 6

7 ABSCO ASSEMBLY INTRODUCTION The snap-tite assembly system locks all perimeter channels to all roof and wall sheets without the need for tools and fasteners. To pre-assemble the four wall panels and two roof panels, the perimeter channels are secured to the top and bottom of each panel using the snaptite system, as detailed on the following pages wherever you see the symbol. SNAP T TE i HIGH SIDE PUSH HIGH SIDE HIGH SIDE HIGH SIDE PUSH After joining sheets together, position channel over one end of the sheets, gently tapping it over the snaptite lugs, working along the sheets to the other end. PUSH Position sheets on timbers, trestles or partly over edge of concrete slab. FASTENING SYMBOLS HIGH SIDE Each perimeter channel must finish flush with the edges of the sheets. the snap-tite system allows adjustment for this process by simply tapping the channel along the sheets until each end is neatly flush. Join components together with one screw at this location only, as some channel sections have extra holes that are not required for this model of garden shed 3mm POP RIVETS 4mm NUT & BOLT SET Do not join components together at this location yet, as the screw may obstruct further assembly of other components PAGE 7

8 DOOR PANEL ASSEMBLY 58C 58A 58B B A 58C 0mm FLANGE B 5mm FLANGE PAGE 8

9 REAR PANEL ASSEMBLY 43B 43B 53C 8F PAGE 9

10 SIDE PANEL ASSEMBLY (TWO REQUIRED) 6B 80A XR X4L 8J PAGE 0

11 ROOF ASSEMBLY 43D 43D 88B 8E 8E 88B PAGE

12 FRONT PANEL ASSEMBLY 53A 34A 89A 53B 90C 89B 79C PAGE

13 DOOR PANEL ASSEMBLY 9A B 9A B NOTE: NUTS AND BOLTS (SUPPLIED) MAY BE USED INSTEAD OF POP RIVETS (SUPPLIED) BY SIMPLY ENLARGING THE HINGE HOLE SETS IN THE JAMB USING A 4MM DRILL BIT NOTE: The two holes required to connect the padbolt hasp for each door have not been pre-punched, to allow for proper alignment. position each hasp centrally over the padbolt shaft, and drill 3mm holes and secure with screws PAGE 3

14 PANEL CONSTRUCTION SIDE WALL PANEL S FIT INTO THE NOTCHED FRONT AND REAR WALL PANEL S REPLACE PADBOLT HASP 0mm SCREWS WITH 0MM SCREWS CONNECT DOOR MULLION SECTIONS WITH SIX 0mm SCREWS PAGE 4

15 FINAL CONSTRUCTION ANCHORING OF SHED LOCATION OF 8 CONCRETE ANCHORS - EACH ANCHOR CONSISTS OF ONE NUT, BOLT, DYNABOLT AND STEEL ANGLE - DRILL A 0mm HOLE INTO THE WALL SHEET BOLT & NUT STEEL ANGLE WALL SHEET SLAB - DRILL A 0mm HOLE INTO THE CONCRETE DYNABOLT PAGE 5